JVC Computer Monitor DT V20L3GZ User Manual
The lightning flash with arrowhead  
symbol, within an equilateral triangle is  
intended to alert the user to the presence  
of uninsulated “dangerous voltage”  
within the product’s enclosure that may  
be of sufficient magnitude to constitute a  
risk of electric shock to persons.  
CAUTION  
RISK OF ELECTRICAL SHOCK  
DO NOT OPEN  
The exclamation point within an  
equilateral triangle is intended to alert  
the user to the presence of important  
operating and maintenance (servicing)  
instructions in the literature  
To reduce the risk of electric shock. Do  
not remove cover (or back). No user  
serviceable parts inside. Refer servicing  
to qualified service personnel.  
CAUTION:  
DT-V24G11Z  
DT-V20L3GZ  
accompanying the appliance.  
INSTRUCTIONS  
Table of Contents  
MULTI FORMAT LCD MONITOR  
Safety Precautions .............................................. 2  
IMPORTANT SAFEGUARDS ........................... 2  
Installation............................................................ 4  
Daily Operations / Connections ......................... 6  
Front panel ....................................................... 6  
Rear panel........................................................ 8  
Available signals............................................. 10  
Menu Configuration—MAIN MENU .................. 12  
Menu Configuration—SET-UP MENU............... 17  
External Control................................................. 21  
About the external control .............................. 21  
Using the MAKE/TRIGGER system ............... 21  
Using the serial communication ..................... 22  
Troubleshooting................................................. 24  
Self-check program ........................................ 25  
Maintenance....................................................... 25  
Specifications .................................................... 26  
General........................................................... 26  
LCD panel ...................................................... 26  
Input/output terminals..................................... 26  
Dimensions..................................................... 27  
The illustration of the monitor is of DT-V24G11Z.  
In the case that you use the monitor for many hours, we recommend that you set “NO  
SYNC ACTION” in “SYNC FUNCTION” to “P.SAVE” in MAIN MENU. This will reduce power  
consumption and relieve strain on the monitor.  
For Customer Use:  
Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference.  
Model No. : DT-V24G11Z / DT-V20L3GZ Serial No. :  
LCT2588-002A-H  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS  
APPARATUS TO RAIN OR MOISTURE.  
WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET  
WITH A PROTECTIVE EARTHING CONNECTION.  
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.  
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.  
IMPORTANT SAFETY INSTRUCTIONS  
1) Read these instructions.  
2) Keep these instructions.  
3) Heed all warnings.  
4) Follow all instructions.  
5) Do not use this apparatus near water.  
6) Clean only with dry cloth.  
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.  
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including  
amplifiers) that produce heat.  
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades  
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide  
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult  
an electrician for replacement of the obsolete outlet.  
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and  
the point where they exit from the apparatus.  
11) Only use attachments/accessories specified by the manufacturer.  
12) Use only with the cart, stand, tripod, bracket, or table specified by the  
manufacturer, or sold with the apparatus. When a cart is used, use caution when  
moving the cart/apparatus combination to avoid injury from tip-over.  
13) Unplug this apparatus during lightning storms or when unused for long periods of  
time.  
14) Refer all servicing to qualified service personnel. Servicing is required when the  
apparatus has been damaged in any way, such as power-supply cord or plug is  
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed  
to rain or moisture, does not operate normally, or has been dropped.  
15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall  
be placed on the apparatus.  
FCC NOTICE  
CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the  
equipment.  
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference when the equipment is operated in a commercial environment. This equipment generates,  
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction  
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential  
area is likely to cause harmful interference in which case the user will be required to correct the interference at  
his own expense.  
IMPORTANT RECYCLING INFORMATION  
This product has a fluorescent lamp that contains mercury. Disposal of these materials  
may be regulated in your community due to environmental considerations. For disposal  
or recycling information, please contact your local authorities or for USA, the Electronic  
Industries Alliance: http://www.eiae.org  
16) Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.  
17) When discarding batteries, environmental problems must be considered and the local rules or laws governing  
the disposal of these batteries must be followed strictly.  
The LCD panel and backlight have life expectancy. Due to the basic characteristics of the LCD panel, an  
afterimage or uneven display may occur. It is recommended that you change images occasionally, activate the  
power saving function, or often turn off the power to reduce the load on the LCD panel. Charges will apply for  
repairs resulting from deterioration due to the passage of time.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Installation  
• Do not rest your arm on the monitor or lean against the monitor.  
• Do not touch the LCD panel when installing the monitor.  
• Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the  
monitor or injury.  
CAUTION  
To detach the stand  
CAUTION  
Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged.  
Attachment screws  
You can place the monitor in the following two ways when using it on the supplied stand.  
You can tilt the monitor as follows.  
When the stand plate is attached to the higher  
position of the stand body (☞ “To adjust the stand  
height” on page 5), you can place the monitor as  
illustrated below.  
Stand body  
Screw holes for stand attachment  
1 Remove the screws on the right side of the stand  
(see the illustration below), then lift the stand up  
by about 148°.  
Monitor  
About 148°  
Screw  
(silver)  
Stand  
About 6°  
0°  
About 6°  
Monitor  
The illustration of the monitor is of DT-V24G11Z.  
2 Attach the removed screws and place the monitor  
• When the monitor is not tilted (0°), the  
guidelines align as illustrated below.  
as illustrated below.  
To install the stand  
When attaching the stand to the monitor, insert the guides of the stand into the guide holes on the monitor to  
place the stand in the correct position. Then fix the stand firmly with the attachment screws.  
Guidelines  
Guide holes  
Guides  
The illustration of the monitor is of DT-V24G11Z.  
The illustration of the monitor is of DT-V24G11Z.  
• You can select the stand height—higher position  
or lower position (☞ “To adjust the stand height” on  
page 5).  
• To place the monitor as illustrated on the left again,  
remove the screws on the right side of the stand,  
return the monitor angle to 0°, then reattach the  
removed screws.  
Screw holes  
for stand  
attachment  
CAUTION  
CAUTION  
• Be careful not to pinch your fingers in the gap  
between the monitor and the stand.  
• When the stand plate is attached to the lower  
position of the stand body, you cannot tilt the  
monitor downward.  
• When lifting up the stand...  
Stand plate  
Monitor  
– lay the monitor on a cloth with the LCD panel  
facing down to prevent the LCD panel from being  
damaged.  
– be careful not to pinch your fingers in the moving  
parts.  
• Make sure of lifting the stand up until it stops  
(about 148°); otherwise the monitor may fall over.  
• Place the monitor on a mat to avoid scratching the  
table surface.  
Stand body  
The illustration of the monitor is of DT-V24G11Z.  
• Do not lift up the stand when the stand plate is  
attached to the lower position of the stand body.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To adjust the stand height  
To change the stand height, detach the stand from the monitor (☞ “To detach the stand” on page 4). Then,  
change the position of the stand plate according to the stand height you want by choosing the screw holes to use.  
To prevent an accidental fall  
Fix the monitor to a wall by using strings.  
Fixing the monitor  
<Higher position>  
<Lower position>  
Attach the hook (not provided) to the VESA mounting holes on the rear panel (use the two holes on the upper  
side) using M4 x 10 mm screws (not provided). Bind the hooks on the rear panel of the monitor to a wall or a pillar  
using durable string.  
Screw holes for higher position  
Screw holes for lower position  
VESA mounting holes  
Stand plate  
Stand plate  
Hook and screw (M4 x 10 mm)  
(not provided)  
Hook (not provided)  
The illustration of the monitor is of DT-V24G11Z.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Daily Operations / Connections  
7 Front panel  
• “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp lights even when the function does not  
actually work).  
Tally lamp  
• The items controlled by the MAKE system cannot be controlled by the buttons on the front panel (“REMOTE ON” is displayed and the lamps do not light).  
This lamp is controlled by the tally function of the  
MAKE/TRIGGER terminal.  
• You can select the color of the tally lamp from  
“GREEN” or “RED” (☞ “TALLY SELECT” in  
“FUNCTION SETTING” on page 17 and “External  
Control” on page 21).  
5
/
/
/
buttons  
p SAFETY MARKER button/lamp  
Displays/hides the safety marker.  
t INPUT SELECT buttons/lamps  
When a menu screen is displayed  
Selects or adjusts menu items (☞ “Menu  
Operations” on page 7).  
Selects an input.  
• Adjust the area of the safety marker in “MARKER”  
of MAIN MENU (☞ page 13).  
SDI 1:  
SDI 2:  
E. AUDIO HD/SD SDI (IN 1) terminal  
E. AUDIO HD/SD SDI (IN 2) terminal  
When no menu screen is displayed  
Selects the audio channels of EMBEDDED AUDIO  
signals (☞ “Audio Channel Selection” on page 7).  
• Pressing button while holding button displays  
the SET-UP MENU (☞ “Menu Operations” on  
page 7).  
• This function does not work when displaying the  
picture in the 1:1 mode.  
• This function does not work when “SAFETY  
MARKER” or “R-SAFETY MARKER” is set to  
“OFF” in “MARKER.”  
DUAL LINK SDI:  
E.AUDIO HD SDI (IN 1, IN 2) terminal  
DVI: DVI-D (HDCP) terminal  
COMPO./RGB: COMPO./RGB terminal  
VIDEO 1: VIDEO (INPUT 1) terminal  
VIDEO 2: VIDEO (INPUT 2) terminal  
• The lamp for the selected input lights.  
• When “SDI DUAL LINK” is set to “ON” in MAIN  
q SCREENS CHECK button/lamp  
Displays only the selected element (R, G, or B) of  
the video signal.  
6 MENU button  
Activates/deactivates the display of the MAIN MENU.  
(☞ “Menu Operations” on page 7)  
The illustration of the monitor is of DT-V24G11Z.  
• Each time you press this button, the picture  
changes in the following order.  
MENU, press SDI 1 or SDI 2 to select DUAL LINK  
(☞ page 12).  
1 Speakers (stereo)  
7 COLOR OFF button/lamp  
y Power lamp  
Unlit:  
RGB (Normal screen)  
Blue screen  
Red screen  
The speakers emit the same audio signal emitted  
from the AUDIO ASSIGN (MONITOR OUT)  
terminals (☞ “ 8 AUDIO ASSIGN (MONITOR OUT)  
terminals” on page 9).  
Displays only the luminance signal.  
• This function does not work for RGB input signals.  
The monitor is completely off (the power  
switch on the rear panel is turned off).  
Green screen  
8 1:1 button/lamp  
w ASPECT button/lamp  
Lights in Green:  
The monitor is on.  
Lights in orange:  
The monitor is off (on standby).  
Flashes in orange:  
The monitor is in the P. SAVE (power  
Displays the picture in the original resolution of the  
input signal.  
• The aspect ratio of the picture may change  
depending on the input signal.  
Changes the aspect ratio of the picture from 4:3  
to 16:9 when the picture of 16:9 aspect ratio is  
squeezed into 4:3 format signal.  
• To return to 4:3, press the button again.  
• This function does not work when displaying the  
picture in the 1:1 mode.  
2 VOLUME adjustment knob  
Adjusts the volume.  
3 Picture adjustment knob  
PHASE: Adjusts the picture hue.  
9 AREA MARKER button/lamp  
Displays/hides the area marker.  
CHROMA: Adjusts the picture color density.  
BRIGHT: Adjusts the picture brightness.  
CONTRAST: Adjusts the picture contrast.  
• PHASE and CHROMA cannot be adjusted for  
certain signal formats.  
• When “COMPONENT PHASE” is set to  
“DISABLE” and an NTSC signal is input, PHASE  
can be adjusted (☞ page 17).  
save) mode (☞ “NO SYNC ACTION” in  
“SYNC FUNCTION” on page 15).  
• Select the style of the area marker in “MARKER”  
of the MAIN MENU (☞ page 13).  
• This function works only when displaying the  
picture in 16:9 aspect ratio.  
• This function does not work when “AREA  
MARKER” or “R-AREA MARKER” is set to “OFF”  
in “MARKER.”  
e SCOPE button/lamp  
Displays/hides the indication of the wave form  
monitor and vector scope (☞  
on page 15).  
• Each time you press this button, the window  
changes in the following order.  
u
button  
“
SCOPE SETTING  
”
Turns on and off (on standby) the monitor.  
• The power switch is equipped on the rear panel of  
the monitor (☞ 1 on page 8).  
No display  
Vector scope  
r T.C. (time code) button/lamp  
Wave form monitor  
4 MUTING button  
Turns off the sound when no menu screen is  
displayed.  
• To cancel the function, press the button again or  
turn the VOLUME adjustment knob.  
• Muting function is also canceled when  
“BALANCE” of “AUDIO SETTING” in the MAIN  
MENU is changed (☞ page 14).  
Activates/deactivates the display of the time data  
(time code) contained in the SDI signal (☞ “On the  
Information Display” on page 7).  
• Select the time code type in “INFORMATION” of  
SET-UP MENU (☞ page 19).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Operations  
Audio Channel Selection  
On the Information Display  
On the Status Display  
The monitor displays the information below.  
• Make the setting to display/hide each information  
using the MENU with the exception of 5,  
controlled with T.C. button (☞ r on page 6).  
• Select the position of the information display  
(☞ “POSITION” in “INFORMATION” on page 19).  
Select audio channels emitted from the speakers  
(L/R) and the AUDIO ASSIGN (MONITOR OUT)  
(OUT1(L)/OUT2(R)) terminals, when EMBEDDED  
AUDIO signals come in to the E. AUDIO HD/SD  
SDI terminal (IN1 or IN2) and SDI input (1 or 2) is  
selected.  
• You have to choose a group of selectable audio  
channels before the channel selection (☞  
“E.AUDIO GROUP” in “AUDIO SETTING” on  
page 14).  
If you press the INPUT SELECT button (☞ t on  
page 6) currently lit, the status of the input signal  
and setting of MUTING are displayed for about 3  
seconds.  
• Make the setting to display/hide the status in  
“STATUS DISPLAY” of the “INFORMATION” (☞  
page 19).  
• When “STATUS DISPLAY” is set to “AUTO” or  
“ON,” the status below is also displayed in the  
following cases:  
1 Display the menu.  
To display the MAIN MENU  
\ Press MENU button.  
To display the SET-UP MENU  
\ Press button while holding button.  
MAIN MENU  
• When a DUAL LINK SDI signal is input, it is  
assigned to SDI 1.  
• The setting is memorized for each input (SDI 1  
and SDI 2).  
– When you change the input  
– When the signal condition of the current input  
changes  
Selected item  
1 Audio level meter  
Operation guide  
SET-UP MENU  
• Not displayed when “LEVEL METER ch” is set  
to “OFF” (☞ “AUDIO SETTING” on page 14).  
2 Signal format  
– When you turn on the monitor  
• When “STATUS DISPLAY” is set to “ON,” the  
signal format will remain displayed 3 seconds  
after the status is displayed.  
1 Press or button when a menu  
• Displayed when “STATUS DISPLAY” is set to  
“ON” (☞ “INFORMATION” on page 19).  
• For the contents displayed, see “Available  
signals” and “On the signal format” on page  
10.  
is not displayed.  
The screen for audio channel selection is  
displayed.  
Selected item  
• The screen for audio channel selection  
automatically disappears in about 30  
seconds after the previous operation.  
3 Source name assigned in “CHARACTER  
SET.”  
Operation guide  
1 Signal format  
Audio channel selection screen  
• Displayed when “SOURCE ID” is set to “ON”  
or “AUTO.”  
• Displayed in large letters when “STATUS  
DISPLAY” is set to “OFF” or “AUTO.”  
☞ “INFORMATION” on page 19  
4 CRC error indication  
• For the contents displayed, see “Available  
signals” and “On the signal format” on page  
10.  
2 Press  
buttons to select an item,  
then press button.  
Selected item  
2 Signal format of DVI input or setting of  
“COMPO./RGB SEL.”  
• For some items, adjustments will be made by  
pressing  
.
2 Press  
buttons to select the left  
buttons to select an  
☞ “COMPO./RGB SEL.” on page 12, “DVI  
INPUT SEL.” on page 20  
Status indication of DUAL LINK/3G SDI  
signal information  
• Displayed when “CRC ERROR” is set to “ON”  
(☞ “INFORMATION” on page 19).  
• A red square is displayed when an error  
occurs.  
(L ch) or right (R ch).  
3 Press  
☞ “NOTE” on page 11  
audio channel.  
5 Time code  
3 Displayed when “SYNC INPUT SEL.” is set  
to “EXT.” (external synchronization)  
☞ “ SYNC FUNCTION” on page 15  
Detailed information of 3G SDI signal input  
• Displays the sampling structure/pixel  
resolution of the signal format.  
• Displayed when the 3G SDI signal is input.  
4 Setting of “MUTING”  
• Each time you press the button, the audio  
channel changes according to the settings of  
“E.AUDIO GROUP” (☞ “NOTE” on page 14).  
• When the input signal includes no time code,  
“TC – –:– –:– –:– –” is displayed (☞ r on  
page 6).  
Ex.: When “MARKER” in the  
MAIN MENU is selected  
6 Data format  
4 Press MENU button.  
The screen for audio channel selection  
disappears.  
• Displayed when “STATUS DISPLAY” (☞  
“INFORMATION” on page 19) is set to “ON”  
and SDI signal is input (not all SDI signals) (☞  
“CLOSED CAPTION” on page 16).  
3 Press  
then press  
adjustments.  
buttons to select an item,  
buttons to make  
• Displayed only when muting is activated (☞  
4 on page 6).  
• When any information of 1, 2, 3, 4, or 6  
above is displayed while signals come in from  
equipment other than a computer, the picture is  
displayed without overlapping the information  
display area.  
Using the audio level meter  
4 Press MENU button to finish the  
You can check the conditions of the current  
EMBEDDED AUDIO signals in the audio level meter  
(☞ “On the Information Display” on the right,“LEVEL  
METER SETTING” in “AUDIO SETTING” on page 14).  
menu operation.  
• Pressing MENU button repeatedly  
deactivates the display of the menu.  
However, the information display will overlap with  
the picture when...  
– displaying the picture with higher resolution  
than the resolution of the panel in 1:1 mode.  
– “SD4:3 LARGE” setting is “ON” (☞ “FUNCTION  
SETTING” on page 17).  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Daily Operations / Connections (cont.)  
7 Rear panel  
1 POWER switch  
Turns AC power on or off.  
• You need to press  
button (☞ u on page 6) to use the monitor after turning on the POWER switch.  
2 AC IN terminal  
AC power input connector.  
Connect the provided AC power cord to an AC outlet.  
• Attach the provided power cord holder to prevent accidental disconnection of the AC power cord (☞  
“Attaching the power cord holder” on page 9).  
CAUTION  
Do not connect the power cord until all other connections are completed.  
3 REMOTE terminal  
Terminal for controlling the monitor by an external control (☞ “External Control” on page 21).  
4 VIDEO (INPUT 1/INPUT 2) terminals (BNC)  
Input (IN) and output (OUT) terminals for the composite signals.  
5 COMPO./RGB (G/Y, B/PB/B-Y, R/PR/R-Y) terminals (BNC)  
Input (IN) and output (OUT) terminals for the analog component (color difference) or analog RGB signals.  
• Select the signal type in “COMPO./RGB SEL.” corresponding to the type of the input signal (☞ page 12).  
6 EXT.SYNC (CS) terminals (BNC)  
Input (IN) and output (OUT) terminals for the external composite sync (Cs) signals.  
• To use these terminals, set “SYNC INPUT SEL.” to “EXT.” (☞ “SYNC FUNCTION” on page 15).  
• The terminals are for all VIDEO (INPUT 1, INPUT 2) and COMPO./RGB.  
• When an external sync signal is input, external synchronization has priority over all VIDEO 1, VIDEO 2 and  
COMPO./RGB input.  
1 2  
7 AUDIO ASSIGN (IN 1/IN 2) terminals (pin jack)  
Security slot  
Attach a security wire to this slot.  
Input terminals for the analog audio signals.  
• Use this terminal for the analog audio connection of the SDI. When a superimposed signal (EMBEDDED  
AUDIO signal on an SDI signal) is input, analog audio signals cannot be input.  
• Select the video input to assign the audio signal in “AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” (☞ “AUDIO  
SETTING” on page 14).  
The illustration of the monitor is of DT-V24G11Z.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8 AUDIO ASSIGN (MONITOR OUT) terminals (pin jack)  
Attaching the power cord holder  
Output terminals for the analog audio signal.  
The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN  
terminal.  
• The terminals output the audio signal through AUDIO ASSIGN (IN 1 or IN 2) terminals when you select the  
video input you have selected for “AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” in “AUDIO SETTING” (☞ page  
14).  
• The power cord holder consists of two parts, a case and a cover.  
• The signal is output from this terminal only when the monitor is on or in “P.SAVE” (power save) mode (☞  
“NO SYNC ACTION” on page 15).  
• The EMBEDDED AUDIO signal...  
– is decoded into an analog signal, then emitted.  
– is emitted only when “SDI 1” or “SDI 2” is selected, and when EMBEDDED AUDIO signals come in to the  
E. AUDIO HD/SD SDI (IN 1 or IN 2) terminal.  
1
2
3
To detach the cover  
AC IN  
terminal  
Cover  
Case  
– has priority over the audio signal input to AUDIO ASSIGN (IN 1 or IN 2) terminals when “SDI-1” or “SDI-2”  
is selected for “AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” and the EMBEDDED AUDIO signal is input to  
E.AUDIO HD/SD SDI (IN 1 or IN 2) terminal.  
9 E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC)  
Input terminals for the HD/SD SDI signals.  
CAUTION  
• Use only the provided screws.  
• Make sure the plug will not be pulled out after the cover is attached to the case.  
• The terminals accept also EMBEDDED AUDIO signals including up to 12 audio channels with a sampling  
frequency of 48 kHz.  
• Use both terminals when selecting DUAL LINK SDI for the input.  
p E. AUDIO HD/SD SDI (SWITCHED OUT) terminal (BNC)  
Output terminal for the HD/SD SDI signals.  
• The SDI signals of the current input (SDI 1 or SDI 2) are re-clocked, then emitted.  
• When an input other than SDI 1 and SDI 2 is selected, the SDI signal of the input selected last time is  
emitted from this terminal.  
• The signals are emitted from this terminal only when the monitor is on or in “P.SAVE” (power save) mode.  
• No signals are emitted when DUAL LINK SDI is selected for the input.  
q DVI-D (HDCP) terminal  
Input terminal for the DVI-D signal compatible with HDCP.  
• When the picture is not displayed correctly, change the setting of “DVI INPUT SEL.” (☞ page 20).  
Note for connections  
• Before making any connections, turn off all the equipment.  
• Use a cord whose plugs correctly match the terminals on this monitor and the equipment.  
• Plugs should be firmly inserted; poor connections could cause noise.  
• When unplugging a cord, be sure to grasp its plug and pull it out.  
• DO NOT connect the power cord until all connections are complete.  
• Refer also to the user manual of each piece of equipment.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Daily Operations / Connections (cont.)  
7 Available signals The following signals are available for this monitor.  
Video signals  
Input terminal  
E. AUDIO SDI (IN 1, IN 2)*2  
Signal format shown in the  
status display (☞ page 7)  
√: Acceptable  
—: Not acceptable  
No.  
Signal name  
NTSC  
VIDEO  
COMPO./RGB(Analog  
DVI-D (HDCP)  
(Digital component/Digital RGB)  
(INPUT1, INPUT2) component/Analog. RGB)*1  
SD/HD (1.5G)  
3G SDI  
—
—
—
—
—
—
—
—
—
—
—
—
√
DUAL LINK  
*1 Analog component/analog RGB  
signals are compatible with G on  
sync signal, Y on sync signals, and  
composite sync signals (CS). The  
separate sync signal (HS/VS) is  
not compatible.  
1
2
3
4
5
6
7
8
9
NTSC  
√
—
—
—
—
√
—
—
—
—
—
√
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
√
—
—
—
—
—
—
—
√
PAL  
PAL  
√
B/W50  
B/W50  
√
B/W60  
B/W60  
√
480/60i  
480/59.94i  
576/50i  
480/60p  
480/59.94p  
480/60i  
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
*2 Compatible with EMBEDDED  
AUDIO signals.  
480/59.94i  
576/50i  
√
*3 The signal is recognized as  
1080/60i, and the status is  
displayed as “1080/60i.”  
√
√
480/60p  
√
—
—
—
—
—
√
*4 The signal is recognized as  
1080/59.94i, and the status is  
displayed as “1080/59.94i.”  
480/59.94p  
576/50p  
√
√
10 576/50p  
√
√
11 640*480/60p  
12 640*480/59.94p  
13 720/60p  
640*480/60p  
640*480/59.94p  
720/60p  
—
—
√
√
√
On the signal format  
√
The following messages appear  
depending on the type of input  
signals and their conditions.  
14 720/59.94p  
15 720/50p  
720/59.94p  
720/50p  
√
√
√
√
√
√
√
√
16 720/30p  
720/30p  
√
√
√
—
—
—
—
—
√
When a DVI-D signal protected  
with HDCP is input  
17 720/29.97p  
18 720/25p  
720/29.97p  
720/25p  
√
√
√
\
“*” (at the end of the indication)  
When no video signal comes in  
\ “NO SYNC”  
√
√
√
19 720/24p  
720/24p  
√
√
√
20 720/23.98p  
21 1080/60i  
720/23.98p  
1080/60i  
√
√
√
When a noncompliant video  
signal comes in  
√
√
√
\ “Out of range”  
22 1080/59.94i  
23 1035/60i  
1080/59.94i  
1035/60i  
√
√
√
√
√
When “COLOR SYSTEM” (☞  
“FUNCTION SETTING” on  
page 17) is set to “AUTO” and  
the noncompliant composite  
video signals come in  
\ “OTHERS”  
√*3  
√*4  
√
√
—
—
√
—
—
√
√*3  
√*4  
√
24 1035/59.94i  
25 1080/50i  
1035/59.94i  
1080/50i  
√
√
26 1080/60p  
27 1080/59.94p  
28 1080/50p  
29 1080/30p  
30 1080/29.97p  
31 1080/25p  
32 1080/24p  
33 1080/23.98p  
34 1080/30psF  
35 1080/29.97psF  
36 1080/24psF  
37 1080/23.98psF  
38 1080/25psF  
1080/60p  
1080/59.94p  
1080/50p  
1080/30p  
1080/29.97p  
1080/25p  
1080/24p  
1080/23.98p  
1080/30psf  
1080/29.97psf  
1080/24psf  
1080/23.98psf  
1080/25psf  
—
—
—
√
—
—
—
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√*3  
√*4  
√
√*3  
√*4  
√
√
√
—
—
—
—
—
√
√
√
√
√
√
√
√
—
—
√
√
Download from Www.Somanuals.com. All Manuals Search And Download.  
Computer signals (preset)  
DVI-D (HDCP) terminals  
Specification of the DVI-D (HDCP) terminal  
Connect it to the DVI-D output terminal on a personal computer.  
Resolution  
Frequency  
Pin  
No.  
Pin  
No.  
Pin  
No.  
Input signal  
Input signal  
Input signal  
No.  
Signal name  
Scan system  
Horizontal  
Horizontal  
Vertical  
Vertical (Hz)  
(kHz)  
31.5  
31.5  
37.9  
48.4  
47.8  
55.9  
64.0  
65.2  
75.0  
74.0  
45.0  
67.5  
37.5  
56.25  
1
2
3
4
5
6
7
8
T.M.D.S Data 2–  
T.M.D.S Data 2+  
T.M.D.S Data 2 shield  
NC  
9
T.M.D.S Data 1–  
T.M.D.S Data 1+  
T.M.D.S Data 1 shield  
NC  
17  
18  
19  
20  
21  
22  
23  
24  
T.M.D.S Data 0–  
T.M.D.S Data 0+  
T.M.D.S Data 0 shield  
NC  
1
2
3
4
5
6
7
8
9
VGA60  
640  
852  
480  
480  
59.9  
59.9  
60.3  
60.0  
60.0  
60.0  
60.0  
60.0  
60.0  
60.0  
60.0  
60.0  
50.0  
50.0  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
10  
11  
12  
13  
14  
15  
16  
WVGA60  
SVGA60  
800  
600  
XGA60  
1024  
1280  
1440  
1280  
1680  
1600  
1920  
1280  
1920  
1280  
1920  
768  
NC  
NC  
NC  
WXGA (1280)  
WXGA+60  
SXGA60  
768  
DDC Clock  
DDC Data  
NC  
+5 V Power  
GND  
T.M.D.S Clock shield  
T.M.D.S Clock+  
T.M.D.S Clock–  
900  
1024  
1050  
1200  
1200  
720  
Hot Plug Detect  
WSXGA+60  
UXGA60*5  
10 WUXGA60*5  
NOTE  
11 720/60p  
12 1080/60p*5  
13 720/50p  
Status indication of DUAL LINK/3G SDI signal information  
When DUAL LINK and 3G SDI signals come in, the status of DUAL LINK is displayed. When “SDI DUAL  
LINK” (☞ page 12) in MAIN MENU is set to “OFF” and a 3G SDI signal comes in, the 3G SDI signal  
information is displayed.  
1080  
720  
14 1080/50p*5  
1080  
*5 For DT-V20L3GZ: When No. 9, 10, 12 or 14 signals come in, thin lines will become obscured because their  
signal resolution is higher than the screen resolution.  
Status indication of DUAL LINK  
• Non-preset signals may not be displayed normally even if their frequency is within the acceptable range (☞  
“Horizontal/vertical frequency (computer signal)” on page 26).  
• When a preset signal comes in, the signal format is shown on the status display. For other signals, the  
resolution is shown.  
When “SDI DUAL LINK” (☞ page 12) in MAIN MENU is set to “ON” and an SDI signal is selected, “DUAL  
LINK” is displayed.  
Status indication of 3G SDI signal information  
Following signal information can be displayed when a 3G SDI signal comes in.  
3G A-1:  
3G A-2:  
3G A-3:  
3G A-4:  
Level A mapping structure 1  
Level A mapping structure 2  
Level A mapping structure 3  
Level A mapping structure 4  
3G B-DS1: Level B data stream 1  
3G B-DS2: Level B data stream 2  
3G B-DUAL: Level B DUAL LINK  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Menu Configuration—MAIN MENU  
For the operation procedure, see page 7.  
PICTURE FUNCTION  
Setting for the picture quality  
DT-V24G11Z  
Item  
APERTURE*1  
(For DT-V24G11Z)  
To do  
Setting value  
OFF, ON  
Activates/deactivates the function at the level set in  
“APERTURE LEVEL.”  
APERTURE FREQ.*1 Select the frequency of the luminance signal compensated in  
OFF, LOW, HIGH  
(For DT-V20L3GZ)  
“APERTURE LEVEL.”  
APERTURE  
Compensate the frequency response of the luminance signal of 01 – 10  
the video signal.  
LEVEL*1  
CTI  
Adjust the clearness of the outlines of the chrominance signal.  
Adjust the clearness of the outlines of the luminance signal.  
Selects a proper mode corresponding to the input picture.  
OFF, NORMAL,  
HARD  
LTI  
OFF, NORMAL,  
HARD  
I/P MODE  
sub menu  
reset  
NORMAL, CINEMA,  
FIELD  
Operation guide  
Shows the buttons for each operation.  
Display the sub menu which enables you to adjust the items of “PICTURE FUNCTION”  
while viewing the actual picture.  
Restore the default settings for all the items in “PICTURE FUNCTION.”  
*1 Memorized for each input.  
Setting value: –20 – +20  
DT-V20L3GZ  
BACK LIGHT  
Adjusts the brightness of the display.  
• Adjust according to the ambient light conditions.  
Setting value: DS1, DS2  
3G SDI LEVEL B  
Selects the data stream from two HD SDI signals multiplexed when a 3G SDI level B signal comes in.  
Setting value: OFF, ON  
SDI DUAL LINK  
Activates/deactivates the DUAL LINK function of SDI signals.  
• “DUAL LINK” is displayed when the setting is set to “ON.” No other status indications of SDI signals are  
displayed.  
Operation guide  
Shows the buttons for each operation.  
• Set this setting to “OFF” when an SDI signal other than DUAL LINK SDI is input.  
Setting value: COMPO. (COMPONENT), RGB  
COMPO./RGB SEL.  
Selects the signal type you want to use for COMPO./RGB terminals.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MARKER*1*2  
Settings for marker functions  
1/2  
Item  
To do  
Setting value  
AREA MARKER*3  
Activate/deactivate the area marker and select the  
style of it.  
☞ “NOTE”  
MARKER ASPECT*3  
Select the aspect ratio of the area marker.  
4:3, 14:9, 13:9, 2.35:1, 1.85:1,  
1.66:1  
SAFETY MARKER  
Activate/deactivate the safety marker and select  
the style of it.  
☞ “NOTE”  
SAFETY AREA  
FRAME  
Adjust the area of the safety marker.  
80% – 100%  
Operation guide  
Shows the buttons for each operation.  
Displays/hides the frame indicating the area of the OFF, ON  
specified aspect ratio.  
CENTER MARKER  
LINE BRIGHTNESS  
Displays/hides the marker indicating the center  
position of the picture.  
OFF, ON  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
Adjust the brightness of the marker.  
HIGH, LOW  
2/2  
Item  
To do  
Setting value  
R-AREA MARKER*3  
Activate/deactivate the area marker and select the  
style of it.  
☞ “NOTE”  
NOTE  
R-MARKER ASPECT*3  
R-SAFETY MARKER  
R-SAFETY AREA  
Select the aspect ratio of the area marker.  
4:3, 14:9, 13:9, 2.35:1, 1.85:1,  
1.66:1  
Setting of “AREA MARKER”, “SAFETY MARKER”, “R-AREA MARKER”,  
“R-SAFETY MARKER”  
The setting values and features are as follows.  
OFF:  
LINE:  
HALF:  
HALF+L:  
Activate/deactivate the safety marker and select  
the style of it.  
☞ “NOTE”  
Adjust the area of the safety marker.  
80% – 100%  
Deactivate the marker.  
Displays the area with an outline.  
• The area marker or the safety marker is displayed by using AREA MARKER or SAFETY MARKER button, or  
external control.  
• Select either non-“R-” items or “R-” items to activate by using external control (☞ “External Control” on page 21).  
• When a picture is displayed in 4:3 aspect ratio, the safety marker for the 4:3 area is displayed.  
• To display the safety marker for the area of a picture displayed in 16:9 aspect ratio, hide the area marker  
(☞ “NOTE”).  
The area outside the specified aspect ratio of the screen is displayed at 50% transparency.  
The area of the specified aspect ratio of the screen is indicated by an outline, and the area  
outside of that is displayed at 50% transparency.  
The area outside the specified aspect ratio of the screen is black. Only the portion of the  
picture within the designated area is displayed.  
BLK.:  
BLK. +L:  
The area of the specified aspect ratio of the screen is indicated by an outline, and the area  
outside of that becomes black so that only the area inside the line is displayed.  
*1 Memorized for each input.  
*2 Not displayed when picture is displayed in the 1:1 mode.  
*3 Displayed only when picture is displayed in 16:9 aspect ratio.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Menu Configuration—MAIN MENU (cont.)  
For the operation procedure, see page 7.  
AUDIO SETTING  
Settings for the audio output balance, EMBEDDED AUDIO signals and level meter  
Item  
To do  
Setting value  
BALANCE  
AUDIO1 ASSIGN.  
Adjust the balance between the right and left speakers.  
L5 – L1, 0, R1 – R5  
Select the video input which the audio signal through  
AUDIO ASSIGN (IN 1) terminal is assigned to.  
SDI-1, SDI-2, DVI, COMP/  
RGB, VIDEO-1, VIDEO-2  
AUDIO2 ASSIGN.  
Select the video input which the audio signal through  
AUDIO ASSIGN (IN 2) terminal is assigned to.  
E.AUDIO GROUP*1  
Select the audio channel group of the EMBEDDED AUDIO  
signals.  
☞ “NOTE”  
☞ “NOTE”  
LEVEL METER  
Adjust the level meter display for the EMBEDDED AUDIO  
signals.  
Adjustment bar  
SETTING*1  
Displayed when selecting  
“BALANCE.”  
Operation guide  
Shows the buttons for each  
operation.  
LEVEL METER ch Select how the audio channels are displayed on the level  
OFF, LINE (Displays  
the channels 1 – 6 at  
the left of the screen  
and 7 – 12 at the right.),  
DIVIDE (Displays the odd  
channels at the left of  
the screen and the even  
channels at the right.)  
meter.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
BAR TYPE  
Select the color of the level meter display.  
3COLORS (3 colors to  
indicate variations in input  
levels), W.100 (white)  
NOTE  
REFERENCE  
LEVEL  
Select the standard input level indicated on the level meter. –20dB, –18dB  
Settings of “E.AUDIO GROUP”  
The setting values and selectable audio channels of EMBEDDED AUDIO signals are as follows.  
OVER LEVEL  
Select the input level’s lower limit indicated in red for the  
“3COLORS” display.  
–10dB, –8dB, –6dB,  
–4dB, –2dB  
(G means GROUP)  
1G:  
channel(s) 1/2/3/4/1+2/3+4/1 – 4 (1G)  
BAR  
BRIGHTNESS  
Select the brightness of the level meter.  
LOW, HIGH  
2G:  
channel(s) 5/6/7/8/5+6/7+8/5 – 8 (2G)  
1-2G:  
3G:  
channel(s) 1/2/3/4/5/6/7/8/1+2/3+4/5+6/7+8/1 – 4 (1G)/5 – 8 (2G)/1 – 8 (1G+2G)  
channel(s) 9/10/11/12/9+10/11+12/9 – 12 (3G)  
PEAK HOLD  
Activates/deactivates the peak hold function of the level  
meter.  
OFF, ON  
1-3G:  
channel(s) 1/2/3/4/5/6/7/8/9/10/11/12/1+2/3+4/5+6/7+8/9+10/11+12/1 – 4 (1G)/5 – 8 (2G)/  
9 – 12 (3G)/1 – 8 (1G+2G)/1 – 12 (1-3G)  
*1 Memorized for each input.  
Example of the level meter display—Level meter position and audio channels  
Ex.: When “LEVEL METER ch” is set to “LINE” and “BAR TYPE” is set to “3COLORS”  
OVER LEVEL  
REFERENCE LEVEL  
Red  
Yellow  
Green  
• The level meter with no audio signal input is displayed in white for “3COLORS”, and in gray for “W.100.”  
• You can select the position of the level meter display—top or bottom of the screen (☞ “POSITION” in  
“INFORMATION” on page 19).  
• When “PEAK HOLD” is set to “ON,” the maximum level meter value will remain displayed for a set period of  
time. (At the time the signal input level reaches the highest value.)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCOPE SETTING*1  
Settings for the wave form monitor and vector scope  
Item  
To do  
Setting value  
–10 – +10  
GAIN  
Adjust the gain level for the incoming wave form data.  
Select the size of the wave form monitor and vector scope window.  
SIZE*2  
POSITION*2  
NORMAL, LARGE  
Select the position of the wave form monitor and vector scope  
window.  
1 (lower right), 2  
(lower left), 3 (upper  
left), 4 (upper right)  
TRANSPARENT Activates/deactivates the function to make the window translucent.  
ON (translucent),  
OFF (normal)  
AUTO OFF  
Activates/deactivates the function to make the wave form monitor and ON, OFF  
vector scope window go off automatically 15 minutes after displaying it.  
WAVE DISPLAY Select the wave form for the wave form monitor.  
Operation guide  
Shows the buttons for each  
operation.  
Y/Pb/Pr (HD signals)  
Y/Cb/Cr (SD signals)  
R/G/B (RGB signals)  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
WAVE FILTER  
Activates/deactivates the low-pass filter for the incoming wave form  
data.  
FLAT (no filter),  
LOWPASS  
WAVE OVER  
LEVEL  
Adjust the over level for the incoming luminance (Y) and RGB  
signals.  
☞ “NOTE”  
MARKING  
Activates/deactivates the function to change the color of a wave form OFF, ON  
when the signal exceeds the limit specified on “LEVEL” (☞ below).  
NOTE  
LEVEL  
Adjust the lower limit for the over level.  
070 – 109  
*1 Wave form monitor does not work for DVI signals (PC input). Vector scope does not work for RGB signals.  
*2 When you set “SIZE” to “LARGE,” the window is displayed in the center of the screen regardress of the “POSITION”  
setting.  
Example of the vector scope  
Ex.: When the color bar is displayed  
Example of the wave form monitor  
Ex.: When the luminance signal is Y, “MARKING” is set to “ON”  
and “LEVEL” is set to “080”  
Red  
White  
SYNC FUNCTION  
Settings for the synchronization with signals  
Item  
To do  
Setting value  
NO SYNC ACTION Select the screen status when no signal is coming in.  
OFF, P.SAVE (power save  
mode), GRAY B. (gray screen)  
DELAY TIME  
Select the period until the screen status changes as selected 30sec., 5min., 15min.  
in “NO SYNC ACTION” after signals stop coming in.  
SYNC INPUT  
Select the sync signal for the VIDEO1, VIDEO2 and  
COMPO./RGB input.  
INT. (Internal sync),  
EXT. (External sync)  
SEL.*3  
Y
LOW LATENCY  
Activates/deactivates the function to shorten the time  
taken to display the picture (low latency function).  
• If the picture is not displayed steadily while “ON” is  
selected, select “OFF.”  
ON, OFF  
Video signal  
Start  
End  
• While “ON” is selected, the displayed picture may  
become unstable when an operation using buttons on  
the front panel or the menu is performed, or when the  
signal format changes.  
• The wave which goes over the value set on “LEVEL” is  
indicated in red.  
• The display differs depending on the input signal or the  
setting of “WAVE DISPLAY.”  
• When setting “NO SYNC ACTION” to “GRAY B.,” the screen color changes to gray and the power consumption  
of the back light is saved by half. Selecting “P.SAVE” (power save mode) saves more power consumption by  
turning off the back light.  
• In the initial setting, “NO SYNC ACTION” is set to “P.SAVE”, and “DELAY TIME” set to “15min.” Change the  
settings if necessary.  
*3 Memorized for each input.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
Menu Configuration—MAIN MENU (cont.)  
CLOSED CAPTION*1  
For the operation procedure, see page 7.  
Settings for CLOSED CAPTION functions  
Video input (NTSC, B/W60)  
Item  
To do  
Setting value  
OFF, ON  
CLOSED CAPTION Activate/deactivate the closed caption.  
DATA FORMAT  
Select the data format of closed caption.  
708,  
608ANC,  
608(708),  
608VBI*2  
SDI input (DATA FORMAT: 608)  
DECODE CH  
Selects the type of closed caption.  
Selects the type of service block.  
CC1, CC2, CC3, CC4,  
TEXT1, TEXT2, TEXT3,  
TEXT4  
SERVICE BLOCK  
SERV.1, SERV.2, SERV.3,  
SERV.4, SERV.5, SERV.6  
Operation guide  
Shows the buttons for each  
operation.  
SDI input (DATA FORMAT: 708)  
• CLOSED CAPTION does not work for the video input formats PAL and B/W50.  
• CLOSED CAPTION does not work for the COMPO./RGB/DVI input.  
• CLOSED CAPTION does not work for the SDI input formats 1035/60i, 1035/59.94i, 1080/60p, 1080/59.94p,  
1080/50p and 3G SDI Level A.  
• Depending on signal format, there maybe a case that the closed captions are not displayed properly.  
• When using the 1:1 mode, closed captions may not be displayed properly.  
*1 Memorized for each input.  
*2 Displayed only when SD SDI signal is input.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Configuration—SET-UP MENU  
For the operation procedure, see page 7.  
FUNCTION SETTING  
Settings for the sub menu display, color system, color of the tally lamp, picture size, intensity of the button lamps  
and the PHASE adjustment.  
Item  
To do  
Setting value  
sub menu  
POSI.  
Select the contents and displaying position of “sub menu.”  
☞ “NOTE”  
COLOR  
SYSTEM  
Select the color system.  
• If the picture is unstable with “AUTO,” select “NTSC” or “PAL.”  
AUTO, NTSC, PAL  
TALLY SELECT Select the color of the tally lamp.  
GREEN, RED  
☞ “NOTE”  
SD4:3 LARGE  
DIMMER  
Change the picture size of 4:3 format signal.  
Select the intensity of the button lamps.  
NORMAL, DARK  
COMPONENT  
PHASE  
Deactivates the function of PHASE adjustment (Picture adjustment knob ENABLE, DISABLE  
and “PICTURE SUB ADJ.” in SET-UP MENU) except when an NTSC  
signal comes in (☞ 3 on page 6).  
Operation guide  
Shows the buttons for each  
operation.  
PICTURE SUB ADJ.  
Adjusts the standard level for the picture adjustment and selects the set-up level for the input video signal.  
Item  
CONTRAST*1  
To do  
Setting value  
–20 – +20  
Adjust the standard level for the contrast adjusted with the  
CONTRAST knob on the front panel.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
BRIGHT*1  
Adjust the standard level for the brightness adjusted with the  
BRIGHT knob on the front panel.  
–20 – +20  
CHROMA*1  
PHASE*1, *2  
NTSC SETUP  
Adjust the standard level for the chroma adjusted with the CHROMA –20 – +20  
knob on the front panel.  
Adjust the standard level for the phase adjusted with the PHASE  
knob on the front panel.  
–20 – +20  
NOTE  
Select the set-up level of the input NTSC signal.  
00 (compliant with  
0% set-up signal),  
7.5 (compliant with  
7.5% set-up signal)  
Settings of “sub menu POSI.”  
The setting values and features are as follows.  
COMPO. LEVEL Select the level of the analog component signal (480i and 576i only). B75 (compliant  
LOWER1:  
UPPER1:  
LOWER2:  
UPPER2:  
Displays the current setting and adjustment bar at the lower part of the screen.  
Displays the current setting and adjustment bar at the upper part of the screen.  
Displays the current setting at the lower part of the screen.  
with BetacamVTR  
7.5% set-up signal),  
B00 (compliant  
with BetacamVTR  
0% set-up signal),  
SMPTE (compliant  
with M2VTR signals)  
Displays the current setting at the upper part of the screen.  
• The adjustment bar is not displayed for some items.  
Settings of “SD4:3 LARGE”  
The setting values and features are as follows.  
sub menu  
reset  
Display the sub menu which enables you to adjust the items in “PICTURE SUB ADJ.” while  
viewing the actual picture.  
OFF:  
ON:  
Fit the vertical picture size into the pixel numbers of the monitor display.  
Fit the vertical picture size into that of the monitor display.  
Restore the default settings for all the items in “PICTURE SUB ADJ.”  
*1 Memorized for each input.  
*2 When “COMPONENT PHASE” is set to “DISABLE” and an NTSC signal is input, PHASE can be adjusted.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
Menu Configuration—SET-UP MENU (cont.)  
For the operation procedure, see page 7.  
SIZE/POSI. ADJ.  
Adjusts the size and position of the picture.  
Item  
H SIZE*1  
To do  
Setting value  
Setting value varies depending on the signals.  
Adjust the horizontal picture size.  
H POSITION*1 Adjust the horizontal picture position.  
V SIZE*1  
Adjust the vertical picture size.  
V POSITION*1 Adjust the vertical picture position.  
sub menu  
Display the sub menu which enables you to adjust the items of “SIZE/POSI. ADJ.” while  
viewing the actual picture.  
reset  
Restore the default settings for all the items in “SIZE/POSI. ADJ.”  
*1 Memorized for each signal format.  
WHITE BALANCE SET.  
Selects the GAMMA correction value, color temperature and adjusts the drive level and cutoff point of each color  
(R/G/B).  
Operation guide  
Shows the buttons for each  
operation.  
Item  
To do  
Setting value  
GAMMA  
Select the GAMMA correction value.  
2.2 (equivalent to Υ 2.2)  
2.35 (equivalent to Υ 2.35)  
2.45 (equivalent to Υ 2.45)  
2.6 (equivalent to Υ 2.6)  
COLOR TEMP. Select the color temperature.  
9300K, 6500K, USER  
R DRIVE  
G DRIVE  
B DRIVE*2  
Adjust the drive level of each color (red, green, and blue). MIN – 000 – MAX (in 256 grades)  
R CUT OFF  
G CUT OFF  
B CUT OFF*2  
Adjust the cutoff point of each color (red, green, and blue). MIN – 000 – MAX (in 256 grades)  
sub menu  
Display the sub menu which enables you to adjust the items in “WHITE BALANCE SET.” while  
viewing the actual picture.  
reset  
Restore the default settings for the drive levels and cutoff points of the selected color  
temperature.  
*2 Memorized for each color temperature.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(☞ “External Control” on pages 21 to 23)  
REMOTE SETTING  
Settings for the external control  
Item  
To do  
Setting value  
SERIAL TYPE  
Select the input terminal used for external control by RS232C, RS485  
serial communication.  
PARALLEL TYPE  
Select the external control method for the MAKE/  
TRIGGER terminal.  
MAKE, TRIGGER, SET  
PIN1  
PIN2  
PIN3  
PIN4  
PIN5  
Assign the control functions to the pins of the MAKE/  
TRIGGER terminal.  
• Assign a function to each pin terminal by selecting  
“SET” in “PARALLEL TYPE” mentioned above.  
(The functions are assigned for “PIN6” – “PIN8”  
and you cannot change the assignment of these  
functions.)  
☞ “Functions controlled by the  
MAKE/TRIGGER system” on  
page 22  
Operation guide  
Shows the buttons for each  
operation.  
INFORMATION  
Settings for the information display of the monitor  
Item  
To do  
Setting value  
POSITION  
UPPER, LOWER  
Select the position to show the information display (☞ “On the  
Information Display” on page 7).  
SOURCE ID  
Select whether the name assigned in “CHARACTER SET.” is  
displayed on the screen (☞ “On the Information Display” on page 7).  
• When “AUTO” is selected, the display color synchronizes with the  
color of the tally lamp while the tally lamp is lit.  
OFF, ON, AUTO  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
CHARACTER  
Assign a name to each video source as you like (10 characters at  
maximum).You can also enter a name using the RS-232C system.  
☞ “NOTE”  
SET.*1  
STATUS DISPLAY  
Select whether the status of the current input and the setting of  
MUTING are displayed on the screen (☞ “On the Status Display” on  
page 7).  
AUTO, OFF, ON  
2
TIME CODE  
CRC ERROR  
Select the type of the TIME CODE display.  
VITC  
D-VITC  
*
2, LTC  
*
,
NOTE  
Select whether the CRC error indication for the input HD SDI signal is  
displayed on the screen (☞ “On the Information Display” on page 7).  
ON, OFF  
Setting of “CHARACTER SET.”  
Assign a name for each video source.  
SUB HOUR METER Display the hours of use (unit: hour).You can reset this item.  
1 Change the input to one that you want to assign a video source name for.  
2 Select “CHARACTER SET.”  
MODEL  
Display the model name of the monitor.  
Display the version of the monitor.  
VERSION  
HOUR METER  
3 Press  
buttons to select the first character.  
• Each time you press button, the character changes as follows. Press button to reverse the order.  
Display the total hours of use (unit: hour). This item is used for maintenance of the  
monitor.You cannot reset this item.  
Space  
*1 Memorized for each input.  
*2 Ancillary time code  
4 Press button to move the arrow to the next space.  
• The characters entered before moving the arrow are memorized.  
5 Repeat steps 3 and 4 (10 characters at maximum).  
6 Press MENU button to store the name.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
Menu Configuration—SET-UP MENU (cont.)  
For the operation procedure, see page 7.  
Setting value: OFF, VOL.LOCK, ALL LOCK  
CONTROL LOCK  
Settings for disabling the buttons on the front panel.  
• The following operations are not available when “VOL.LOCK” is selected.  
– VOLUME adjustment knob  
– Picture adjustment knob  
• The “ALL LOCK” function disables to control the buttons on the front panel. But following operations are  
available.  
– Turning on/off (on standby) the monitor  
– Displaying the SET-UP MENU (by pressing button while holding button) and turning “CONTROL LOCK”  
to “OFF”  
– Operating the monitor by an external control  
If you try other operations, “  
Control lock on!” appears on the screen.  
Setting value: AUTO, COMPO., RGB, PC  
DVI INPUT SEL.  
When “AUTO” is selected, the format of signals come in to the DVI-D (HDCP) terminal is automatically  
recognized. (Normally, select “AUTO.”)  
• Select “COMPO.,” “RGB” or “PC” when the picture is not displayed correctly with “AUTO.”  
• DVI-D input of the monitor is compatible with HDCP.  
Operation guide  
Shows the buttons for each  
operation.  
Setting value: AUTO, MS1YCbCr, MS2YCbCr, MS3YCbCr, MS4YCbCr, MS2 RGB, MS3 RGB, 3G-B-DS  
SDI FORMAT  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
When “AUTO” is selected, 3G SDI/HD-SDI DUAL LINK signals are automatically recognized. (Normally select  
“AUTO.”)  
• If the picture is unstable with “AUTO”, select the setting value according to the input signal format.  
• “M” is displayed on the status display when a setting other than “AUTO” is selected.  
all reset  
Restores all the settings and adjustments of the monitor to the default.  
• “HOUR METER” and the settings done by using the adjustment knobs on the front panel will not be reset.  
• After performing “all reset,” the monitor is turned off then turned on automatically.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
External Control  
7 About the external control  
7 Using the MAKE/TRIGGER system  
This monitor has three external control terminals.  
The MAKE/TRIGGER terminal is configured as follows.You can assign a function to each pin terminal in  
“REMOTE SETTING” (☞ “PIN1, PIN2, PIN3, PIN4, PIN5” in “PARALLEL TYPE” on page 19).  
• You cannot change the functions assigned to the pin terminals from 6th to 8th.  
• MAKE/TRIGGER terminal (RJ-45): The following external control systems are available.  
(1) MAKE (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to  
the GND pin terminal, or disconnecting (opening) it.  
(2) TRIGGER (trigger) system: Controls the monitor by sending the pulse signal instantaneously to the  
corresponding pin terminal.  
☞ “Using the MAKE/TRIGGER system” on the right  
Pin No.  
Pin name  
1
2
3
4
5
6
7
8
PIN1  
PIN2  
PIN3  
PIN4  
PIN5  
TALLY*1  
• RS-485 terminals (RJ-45): Controls the monitor with the RS-485 system (☞ “Using the serial communication”  
on page 22).  
• RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS-232C system (☞ “Using the serial  
communication” on page 22).  
This is a female terminal.  
Set the following items of “REMOTE SETTING” in SET-UP MENU according to the external control terminal and  
control system (☞ “SERIAL TYPE,” “PARALLEL TYPE” on page 19).  
ENABLE*2  
GND  
The settings of this unit  
Control terminal  
Control system  
MAKE  
“PARALLEL TYPE”  
setting  
“SERIAL TYPE” setting  
*1 The 6th pin terminal controls turning on or off the tally lamp (available to control even when the 7th pin terminal  
is invalid).  
MAKE/TRIGGER  
terminal  
—
—
MAKE  
TRIGGER  
—
*2 The 7th pin terminal makes the external control valid/invalid. Make sure to control the terminal by the MAKE  
system.  
TRIGGER  
RS-485 terminal  
RS-232C terminal  
Serial  
RS-485  
RS485*1  
RS232C*1  
communication  
RS-232C  
—
To assign the functions to the pin terminals  
*1 For a monitor connected to a personal computer etc, select the terminal the equipment is actually connected to.  
For other monitors, select “RS485.”  
For the operation procedure, see page 7.  
1 Select “REMOTE SETTING” on the SET-UP MENU.  
Control priority is as follows.  
MAKE > TRIGGER = serial communication = buttons and menu on the monitor  
2 Set “PARALLEL TYPE” to “SET.”  
3 Select a pin name (“PIN1” – “PIN5”) for which you want to assign a function, then select the function you want  
to assign.  
• You can use external control even when “CONTROL LOCK” is set to “VOL.LOCK” or “ALL LOCK” (☞ page 20).  
• When the monitor is off (on standby), external control is not available. But certain external controls (starting/  
terminating communication, turning on the monitor) are available through the serial communication (☞ page 23).  
• For the selectable functions, see the table on page 22.  
<MAKE/TRIGGER system>  
Operation of the external control  
You can control the monitor by a personal computer or dedicated controller*2.  
• “Using the MAKE/TRIGGER system” on the right.  
1 Set “PARALLEL TYPE” of “REMOTE SETTING” to “MAKE” or “TRIGGER” in the SET-UP MENU.  
2 Short-circuit the 7th pin terminal (ENABLE) to the 8th pin terminal (GND) so that the monitor can be controlled  
by the external control.  
*2 The controller is not commercially available. Consult your dealer if you need it.  
3 When the “MAKE” system is selected: Operate each function by short-circuiting the corresponding pin terminal  
<Serial communication>  
to the 8th pin terminal (GND) or opening it.  
When the “TRIGGER” system is selected: Operate each function by pulse control, that is short-circuiting the  
corresponding pin terminal to the 8th pin terminal (GND) for about 1 second and opening it.  
PC, etc.  
• When changing the input with MAKE system, only one pin terminal must be short-circuited. (Other pin terminals  
must be opened.)  
• When selecting the “TRIGGER” system, you can operate only one function at a time. Operate the functions one  
by one.  
RS-485 RS-485  
OUT IN  
RS-485  
OUT  
RS-485  
IN  
RS-485  
OUT  
RS-485 IN  
or  
RS-232C  
• For the details, see page 22.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
External Control (cont.)  
*5 While controlling with the MAKE system, the wave form monitor and vector scope is switched between  
<Functions controlled by the MAKE/TRIGGER system>  
displayed (short-circuting) and hidden (opening) regardless of the “AUTO OFF” setting in the MAIN MANU.  
While controlling with the TRIGGER system, the screen is switched in the same way as when pressing the  
SCOPE button (☞ e on page 6). If the wave form monitor and vector scope are input at the same time, the  
wave form monitor is displayed.  
Display  
TALLY SEL  
Functions to be controlled  
Selects the color of the tally lamp.  
Changes the input to “SDI 1.”  
Changes the input to “SDI 2.”  
Changes the input to “DVI.”  
Changes the input to “COMPO./RGB”  
Changes the input to “VIDEO 1.”  
Changes the input to “VIDEO 2.”  
Changes the sync signal.  
Opening  
Green  
Invalid  
Invalid  
Invalid  
Invalid  
Invalid  
Invalid  
Internal sync  
DS 1  
Short-circuiting  
Red  
Valid  
Valid  
Valid  
Valid  
Valid  
Valid  
External sync  
DS 2  
On  
SDI 1  
*6 While controlling with the MAKE system, the screen is switched between normal screen (opening) and blue  
screen (short-circuiting). While controlling with the TRIGGER system, the screen changes in the same way as  
when pressing SCREENS CHECK button (☞ q on page 6).  
SDI 2  
DVI  
*7 Must be controlled with the TRIGGER system. The mode changes in the order of “NORMAL”  
“FIELD.” (This function cannot be controlled with the MAKE system.)  
\
“CINEMA”  
\
COMP./RGB  
VIDEO 1  
VIDEO 2  
EXT.SYNC  
3G-B.DS  
DUAL LINK  
A.MARKER  
S.MARKER  
FRAME  
• You cannot assign the same function to different pin terminals.  
• The TRIGGER system switches each function by short-circuiting the pin terminal for about 1 second and  
opening it.  
Selects the “3G SDI LEVEL B” data stream.  
Turns on or off “SDI DUAL LINK.”  
The area marker indication  
The safety marker indication  
Indication of the area of the specified aspect ratio  
The center marker indication  
Selects the items of “MARKER”*1  
Changes the aspect ratio.  
7 Using the serial communication  
Off  
You can control the monitor from a personal computer etc. via the RS-485 or RS-232C terminal.  
• Consult your dealer for the details of the external control specification.  
Off  
On  
Off  
On  
<Communication specifications>  
Off  
On  
Input  
terminal  
Terminal  
specification  
C.MARKER  
MARK.SEL  
ASPECT  
1:1  
Off  
On  
Cable  
Communication specifications  
Non-“R-” items  
4:3  
“R-” items  
16:9  
RS-485  
RS-232C  
A straight LAN cable  
Baud Rate: 4800 bps  
Data Bits: 8 bits  
Parity: No parity  
Stop Bits: 1 bit  
Flow Control: No control  
Communication Code: ASCII Code  
A straight cable with a D-sub  
9-pin connector (male for the  
monitor, female for the personal  
computer etc.)  
Displays in 1:1 mode.  
Off  
On  
☞ See below  
STATUS  
Status display*2  
☞ “On the Status Display” on page 7  
3
L.METER  
TIME CODE  
SOURCE ID  
WAVE FORM  
VECTOR  
C.C.  
Audio level meter display  
*
Time code display  
Off  
On  
4
5
5
*
*
*
<Specifications of the RS-485 terminal>  
Pin No.  
☞ “SOURCE ID” in “INFORMATION” on page 19  
Wave form monitor display  
Vector scope display  
IN terminal signal OUT terminal signal  
1
2
3
4
5
6
7
8
TXD +  
TXD +  
TXD –  
RXD +  
NC  
Closed caption display  
Off  
On  
TXD –  
RXD +  
NC  
COLOR OFF  
SCR CHECK  
I/P MODE  
MUTING  
DIMMER  
– – –  
Color off  
Color  
Monochrome  
6
7
Screens check  
*
*
Change a mode according to a input picture.  
Muting on/off  
NC  
NC  
Off  
NORMAL  
—
On  
DARK  
—
RXD –  
NC  
RXD –  
NC  
This is a female terminal.  
Change the intensity of the button lamps.  
No function  
GND  
GND  
*1 Selects which functions in “MARKER” are activated, non-“R-” items or “R-” items (☞ “MARKER” on page 13).  
*2 Displays the information shown when INPUT SELECT button of the current input is pressed (☞ “On the Status  
Display” on page 7). While controlling with the MAKE system, the information is displayed only at the moment of  
short-circuiting.  
<Specifications of the RS-232C terminal>  
Pin No.  
Signal  
1
2
3
4
5
6
7
8
9
NC  
*3 While controlling with the MAKE system, the level meter is switched between displayed (short-circuiting) and  
hidden (opening). When “LEVEL METER ch” is set to “OFF,” the level meter is not displayed (“NO EFFECT”  
appears).  
RXD  
TXD  
NC  
While controlling with the TRIGGER system, the pattern of the audio channel display is switched.  
*4 While controlling with the MAKE system, the available set-up options will be the setting value currently selected  
in “SOURCE ID” (“ON” or “AUTO” [short-circuiting]) and “OFF” (opening). While controlling with the TRIGGER  
system, uses the same set-up option as those in the SET-UP MENU (☞ “SOURCE ID” in “INFORMATION” on  
page 19).  
GND  
NC  
This is a female terminal.  
RTS  
CTS  
NC  
• The 7th terminal and the 8th  
terminal are connected.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
<Command outline>  
All commands consist of the following segments.  
Example of communication procedures  
1Starting the communication:  
Header  
Monitor ID  
Command ID  
Function  
Data  
Cr (0Dh)  
connection command (!00BCN1Cr)  
Monitor  
On Header  
2Monitor’s status (@00BOKCr)  
“!”: Operation commands from the personal computer, etc. For details, see <Basic command list> below.  
“?”: Reference commands from the personal computer, etc.  
“@”: Status returns from the monitor  
3Selecting “SDI 1” input (!00BINACr)  
4Monitor’s status (@00BOKCr)  
To start communication, send the connection command from the personal computer etc.  
To terminate the communication, send the termination command from the personal computer etc.  
PC, etc.  
5Terminating the communication:  
termination command (!00BCN0Cr)  
6Monitor’s status (@00BOKCr)  
<Basic command list>  
No.  
1
Commands  
Functions  
Data  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
I
N
N
D
D
D
D
E
P
O
D
D
E
W
W
N
N
N
N
N
N
I
1
0
Cr  
Cr  
E
Starts communication (connection)  
Terminates communication (termination)  
x*2 Cr Assigns the control ID  
No data  
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
2
No data  
3
S
R
D
C
N
Cr  
W
J
T
T
x
Cr  
x
01 – 99  
4
I
E
Initializes the control ID  
x*2 Cr Displays/hides the ID  
No data  
5
I
S
P
00: Hide, 01: Display  
00: Hide, 01: Display  
No data  
6
I
H
U
K
x
x*2 Cr Flashes/hides the selected ID No. of the monitor  
Displays the MAIN MENU/Quits the menu operation  
Moves the cursor upward ( )  
7
M
U
D
A
A
S
P
P
I
Cr  
8
No data  
9
N
R
Cr  
Cr  
Cr  
P
No data  
Moves the cursor downward ( )  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
Makes setting/adjustment (  
Makes setting/adjustment (  
Displays the SET-UP MENU  
Turns on the monitor  
)
)
No data  
J
L
No data  
T
U
Cr  
No data  
1
Cr  
Cr  
Cr  
Cr  
Cr  
Cr  
Cr  
Cr  
P
No data  
0
Turns off the monitor (on standby)  
Selects “SDI 1” input  
No data  
A
B
C
D
E
F
No data  
I
Selects “SDI 2” input  
No data  
I
Selects “DVI” input  
No data  
I
Selects “COMPO./RGB” input  
Selects “VIDEO 1” input  
Selects “VIDEO 2” input  
Displays the status*3  
No data  
I
No data  
I
No data  
D
A
A
S
U
P
Cr  
E
x*2 Cr  
No data  
M
S
T
x
x*2 Cr Turns muting on/off  
00: Off, 01: On  
00: 4:3, 01: 16:9  
x
Changes the aspect ratio  
• “Cr” is 0Dh.  
• The commands for starting communication (connection) (No. 1), terminating communication (termination) (No. 2), and turning on the monitor (No. 13) can be used while the monitor is off (on standby).  
*1 Enter the monitor’s ID for “ **.” The initial setting of the monitor’s ID is “00.” When connecting several monitors, “00” is a command for controlling all monitors at once.  
*2 Enter the appropriate data to “xx.”  
*3 Displays the information shown when the INPUT SELECT button currently lit is pressed (☞ “On the Status Display” on page 7).  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
Troubleshooting  
Solutions to common problems related to the monitor are described here. If none of the solutions presented here  
solve the problem, unplug the monitor and consult an authorized dealer or service center.  
Symptom  
Probable cause and corrective action  
Page  
Symptom  
Probable cause and corrective action  
Page  
6
8
8
• Adjust the picture contrast or brightness by using the adjustment  
knobs on the front panel. Or, adjust “CONTRAST” or “BRIGHT” of  
“PICTURE SUB ADJ.” in the SET-UP MENU.  
6, 17  
• Press the  
• Firmly insert the AC power plug.  
• Turn on the POWER switch on the rear panel.  
button.  
The picture becomes  
blurred.  
No power supply  
• Check whether the setting of 1:1 or ASPECT buttons is appropriate.  
• Check whether the input signal format is acceptable on the monitor.  
Wrong picture position, • Adjust the picture size (H SIZE/V SIZE) or position (H POSITION/V  
6
• Select the correct input using the INPUT SELECT buttons.  
• Connect the signal cable firmly.  
• Turn on the power of the connected component and set the output  
correctly.  
6
8
—
10, 11  
18  
No picture with the  
power on  
wrong picture size.  
POSITION) of “SIZE/POSI. ADJ.” in the SET-UP MENU.  
• For some signals, the picture cannot be displayed fully in the effective  
screen area. There is no sure method to solve this problem.  
—
—
• Check whether the input signal format is acceptable on the monitor.  
10, 11  
• Adjust the volume level.  
6
6
8
• The items which are not available for the current input or the current  
input signal are not displayed on the menu. Change the input or the  
input signal.  
• The items controlled by the MAKE system do not appear on the  
menu.  
• Deactivate the muting function.  
• Connect the signal cable firmly.  
• Turn on the power of the connected component and set the output  
correctly.  
No sound  
Some items do not  
appear on the menu.  
—
21  
“OTHERS” or “Out of  
range” appears.  
• Check whether the input signal format is acceptable on the monitor.  
10, 11  
• Set “CONTROL LOCK” in the SET-UP MENU to “OFF.”  
• You cannot use the buttons for the items controlled by the MAKE  
system. Disable the external control.  
20  
21, 22  
Buttons on the monitor  
do not work.  
• Select the correct input using the INPUT SELECT buttons.  
• Connect the signal cable firmly.  
6
8
• Turn on the power of the connected component and output video  
signals. Or, check whether the video output of the component (video  
output setting of the VCR or graphic board of the computer) is set  
correctly.  
—
“NO SYNC” appears.  
• Adjust each picture adjustment knob on the front panel or adjust the  
items of “PICTURE SUB ADJ.” in the SET-UP MENU. Or, perform  
“reset” in “PICTURE SUB ADJ.”  
6, 17  
• Check whether the setting of COLOR OFF or SCREENS CHECK  
buttons are appropriate.  
6
Wrong color, no color  
• Select the proper color system (“COLOR SYSTEM”) in “FUNCTION  
SETTING” of the SET-UP MENU.  
• Adjust the items of “WHITE BALANCE SET.” in the SET-UP MENU.  
Or, perform “reset” in “WHITE BALANCE SET.”  
17  
18  
The following are not malfunctions.  
• When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has  
changed. Though the remaining picture will disappear after a while, there may be a case that it remains  
for a long period depending on the length of time the still image was displayed for. This is due to the  
characteristics of the LCD display and is not a malfunction.  
• Red spots, blue spots and green spots on the panel surface are a normal characteristic of LCD displays,  
and not a problem. The LCD display is built with very high precision technology; however, be aware that a  
few pixels may be missing or constantly lit.  
• The following symptoms are problems only when pictures or sounds are not played back normally.  
– A slight electric shock occurs when you touch the monitor.  
– The top and/or rear panel of the monitor becomes hot.  
– The monitor emits a cracking noise.  
– The monitor emits a mechanical noise.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
Troubleshooting (cont.)  
Unplug this product from the wall outlet before cleaning.  
7 Self-check program  
This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes  
troubleshooting easier. Whenever a problem occurs, one or some of the INPUT SELECT lamps will flash. If this  
happens, follow the steps below and contact your dealer to resolve the problem.  
Screen  
To avoid irreparable change in appearance of the screen such as uneven color, discoloration, scratches, be  
careful about the following:  
• Do not paste or stick anything using any glues or adhesive tapes.  
• Do not write anything on the screen.  
• Do not strike the screen with a hard object.  
• Avoid condensation on the screen.  
• Do not wipe the screen with solvent such as alcohol, thinner, or benzine.  
• Do not wipe the screen forcefully.  
Wipe stains off the screen with a soft cloth. If the screen gets heavily stained, wipe it with a soft cloth soaked in  
water-diluted neutral detergent and wrung well, then wipe with a soft dry cloth.  
Cabinet  
To avoid the deterioration or damages of the cabinet such as its paint’s peeling away, be careful about the  
following:  
• Do not wipe the cabinet using solvent such as alcohol, thinner, or benzine.  
• Do not expose the cabinet to any volatile substance such as insecticides.  
• Do not allow any rubber or plastic in contact for a long time.  
• Do not wipe the cabinet forcefully.  
The illustration of the monitor is of DT-V24G11Z.  
Wipe stains off the cabinet with a soft cloth. If the cabinet gets heavily stained, wipe it with a soft cloth soaked in  
water-diluted neutral detergent and wrung well, then wipe with a soft dry cloth.  
When the screen goes blank, and one or some of the INPUT SELECT lamps (COMPO./RGB, VIDEO1,  
VIDEO2) on the front control panel start flashing...  
Ventilation openings  
Use a vacuum cleaner to get rid of the dust around the intakes (all the openings). If a vacuum cleaner is not  
available, use a cloth and wipe it off. Leaving the dust around the intakes may prevent proper temperature control  
and cause damage to the product.  
1 Check which lamps are flashing.  
2 Press  
button to turn off (on standby) the monitor.  
3 Turn off the power switch on the rear panel.  
4 Disconnect the AC power cord from the AC outlet.  
5 Contact your dealer with the information about which lamps were flashing.  
• If you turn on the monitor soon after turning it off (or after a short-term power failure), the INPUT SELECT  
lamps may flash and no image may be displayed.  
When this happens, turn off power and wait at least 10 seconds before turning on the monitor again.  
If the INPUT SELECT lamps do not flash, you can use the monitor as normal.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
Specifications  
7 General  
7 LCD panel  
Model name  
DT-V24G11Z  
DT-V20L3GZ  
Type 20 wide format  
Model name  
Type  
DT-V24G11Z  
DT-V20L3GZ  
Type  
Multi format LCD monitor  
Type 24 wide format  
16:10  
24˝ wide, active matrix TFT  
20˝ wide, active matrix TFT  
Screen size  
Aspect ratio  
Effective screen size  
Width:  
518.4 mm (20 1/2˝)  
Height: 324 mm (12 7/8˝)  
Width:  
433.4 mm (17 1/8˝)  
Height: 270.9 mm (10 3/4˝)  
Number of pixels displayed  
Number of colors displayed  
Viewing angle (TYP.)  
Brightness (TYP.)  
1 920 x 1 200  
1 680 x 1 050  
Horizontal/vertical frequency  
(computer signal)  
H: 31.469 kHz – 75.000 kHz  
V: 48 Hz – 65 Hz  
16.77 million  
* Some signals within this frequency range may not be displayed (“Out of  
range” is displayed).  
178° (Horizontally), 178° (Vertically)  
400 cd/m2  
178° (Horizontally), 178° (Vertically)  
470 cd/m2  
Compliant video signal format  
Format  
☞ “Available signals” on page 10  
Contrast ratio (TYP.)  
1000:1  
700:1  
3G SDI: SMPTE424M/SMPTE425M  
DUAL LINK HD SDI:  
SMPTE372M  
7 Input/output terminals  
HD SDI: BTA S-004C, SMPTE292M  
SD SDI: ITU-R BT.656: 525/625  
SMPTE259M: 525  
EMBEDDED AUDIO:  
SMPTE299M, SMPTE272M  
CLOSED CAPTION:  
Model name  
DT-V24G11Z  
DT-V20L3GZ  
VIDEO (INPUT 1)  
Input/output of composite signal:  
2 line, BNC connector x 4,  
1 V(p-p), 75 Ω  
VIDEO (INPUT 2)  
DVI-D (HDCP)  
* The input (IN) and output (OUT) terminals are bridge-  
connected (auto termination).  
EIA/CEA-608, EIA/CEA-708  
Audio output  
Internal speaker: 1.0 W + 1.0 W  
DVI-D signal input (compatible with HDCP):  
DVI-D connector x 1 (compatible with DDC2B)  
Operating conditions  
Operating temperature: 5°C – 35°C (41°F – 95°F)  
Operating humidity: 20% – 80% (non-condensing)  
(Slightly variable depending on ambient conditions for installation.)  
COMPO./RGB (G/Y, B/PB/B-Y, Input/output of analog component signal/analog RGB signal:  
R/PR/R-Y)  
1 line, BNC connector x 6  
Power requirements  
Rated current  
AC 120 V, 50 Hz/60 Hz  
G/Y: 1 V(p-p), 75 Ω (including sync signal)  
B/PB/B-Y, R/PR/R-Y: 0.7 V(p-p), 75 Ω  
* The input (IN) and output (OUT) terminals are bridge-  
connected (auto termination).  
1.15 A  
1.00 A  
External dimensions  
(excluding protruding parts)  
Width:  
Width:  
564 mm (22 1/4˝) 564 mm (22 1/4˝)  
477 mm (18 7/8˝) 477 mm (18 7/8˝)  
Height:  
394.6 mm (15 5/8˝) 354 mm (14˝)  
Depth:  
243 mm (9 5/8˝)  
EXT.SYNC (CS)  
Input/output of composite sync signal:  
Height:  
1 line, BNC connector x 2,  
0.3 V(p-p) – 4 V(p-p),  
75 Ω (tri-level sync, negative polarity sync (bi-level), and BB)  
(including no video signal)  
* The input (IN) and output (OUT) terminals are bridge-  
connected (auto termination).  
448.6 mm (17 3/4˝) 408 mm (16 1/8˝)  
Depth:  
243 mm (9 5/8˝)  
99 mm (4˝)  
99 mm (4˝)  
(with the stand)  
(without the stand)  
(with the stand)  
(without the stand)  
Weight  
11.5 kg (25.3 lbs) (with the stand)  
8.6 kg (18.9 lbs) (without the stand)  
10.6 kg (23.3 lbs) (with the stand)  
7.7 kg (16.9 lbs) (without the stand)  
E. AUDIO HD/SD SDI (IN 1)  
E. AUDIO HD/SD SDI (IN 2)  
Digital signal input (compatible with EMBEDDED AUDIO/DUAL LINK signals):  
auto detection, 2 line, BNC connector x 2  
Accessories  
AC power cord, Power cord holder x 1, Screw x 2 (for power cord holder)  
E. AUDIO HD/SD SDI  
(SWITCHED OUT)  
Digital signal output (compatible with EMBEDDED AUDIO signals):  
1 line switched out, BNC connector x 1  
Notice on transportation  
This monitor is precision equipment and needs dedicated packing material for transportation.  
Never use any packing material supplied from sources other than JVC or JVC-authorized dealers.  
AUDIO ASSIGN (IN 1)  
AUDIO ASSIGN (IN 2)  
Analog audio signal input:  
2 line, RCA connector x 4,  
500 mV (rms), high impedance  
AUDIO ASSIGN  
(MONITOR OUT)  
Analog audio signal output: 1 line, RCA connector x 2,  
500 mV (rms)  
• For easy understanding, pictures and illustrations are shown by being emphasized, omitted or composed,  
and may be slightly different from actual products.  
• Design and specifications are subject to change without notice.  
• All company names and product names mentioned herein are used for identification purposes only, and  
may be the trademarks or registered trademarks of their respective companies.  
REMOTE (MAKE/TRIGGER)  
REMOTE (RS-485)  
☞ “Using the MAKE/TRIGGER system” on page 21  
☞ “Using the serial communication” on page 22  
REMOTE (RS-232C)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications (cont.)  
Unit: mm (inch)  
7 Dimensions  
DT-V24G11Z  
<Front view>  
<Side view>  
<Rear view>  
99 (4)  
51.9 (2 1/8)  
1.3 (1/16)  
VESA mounting holes  
(Size: 4-M4, depth: 10 mm)  
564 (22 1/4)  
100  
51 (2 1/8)  
300 (11 7/8)  
243 (9 5/8)  
DT-V20L3GZ  
<Front view>  
<Side view>  
<Rear view>  
99 (4)  
52.7 (2 1/8)  
1.3 (1/16)  
VESA mounting holes  
(Size: 4-M4, depth: 10 mm)  
477 (18 7/8)  
100  
51 (2 1/8)  
300 (11 7/8)  
243 (9 5/8)  
* at the higher position  
**at the lower position  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DT-V24G11Z/DT-V20L3GZ MULTI FORMAT LCD MONITOR  
© 2011 Victor Company of Japan, Limited  
0111TMH-MW-MT  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Insignia Car Satellite TV System NS 42L260A13 User Manual
JAMO Speaker S 506 HCS 3 User Manual
JL Audio Car Amplifier J23602 User Manual
JVC Car Stereo System GET0266 003A User Manual
JVC DVR SR DVM700U User Manual
Karcher Pressure Washer 300 User Manual
Kenwood Universal Remote B60 3617 00 User Manual
KitchenAid Food Warmer 4452828 User Manual
Korg Musical Instrument KONTROL49 User Manual
Kramer Electronics Marine Radio VP 4x4 User Manual