CASSETTE RECEIVER
KS-F184
For installation and connections, refer to the separate manual.
INSTRUCTIONS
GET0308-001A
[UI]
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF THE BUTTONS
Control panel
Display window
1
(standby/on/attenuator) button
r
t
/
buttons
(control panel release) button
2 S BASS (super bass) button
3 0 (eject) button
y EX (extra) button
4 Display window
5 Cassette compartment
6 1/¡ PROG (program) button
7 SCM (sound control memory) button
8 FM AM button
9 +/– buttons
p SEL (select) button
Display window
u FM band indicators
FM1, FM2, FM3
i AM band indicator
o Sound mode indicators
BEAT, SOFT, POP
q Number buttons
; Tuner reception indicators
MO (monaural), ST (stereo)
w MO (monaural) button
• Also functions as SSM buttons when pressed
together with DISP (display) button.
e DISP (display) button
.
a S BASS (super bass) indicator
s Main display
• Also functions as SSM buttons when pressed
together with MO (monaural) button.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
1 3
2
Turning on the power
3 Adjust the volume.
1 Turn on the power.
To increase the volume
Note on One-Touch Operation:
To decrease the volume
When you select a source in step 2 below, the
power automatically comes on. You do not have
to press this button to turn on the power.
2 Select the source.
Volume level appears.
4 Adjust the sound as you want.
(See pages 10 and 11.)
To drop the volume in a moment
To operate the tuner (FM or AM),
see pages 6 – 8.
To operate the EX (extra) button,
see page 8.
Press
briefly while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.
To play a tape,
see page 9.
To turn off the power
Press and hold
second.
for more than one
“SEE YOU” appears, then the unit turns off.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the clock
4 Finish the setting.
1 Press and hold SEL (select) for more
than 2 seconds.
“CLOCK H” or “CLOCK M”
appears on the display.
To check the current clock time or change the
display mode
Press DISP (display) repeatedly.
Each time you press the button,
the display mode changes as
follows:
2 Set the hour.
1 Select “CLOCK H” (hour) if not shown on
the display.
2 Adjust the hour.
• During tuner operation:
1
2
• During tape operation:
3 Set the minute.
1 Select “CLOCK M” (minute).
2 Adjust the minute.
1
2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
RADIO OPERATIONS
Searching for a station manually:
Listening to the radio
Manual search
You can use either automatic searching or manual
searching to tune in to a particular station.
1 Select the band (FM1 – 3, AM).
Note:
When a cassette is in the cassette compartment, you
cannot select the tuner. Be sure to eject the cassette
from the cassette compartment to listen to the radio.
Note:
Searching for a station automatically:
Auto search
1 Select the band (FM1 – 3, AM).
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
2 Press and hold
or
until
“M” (manual) starts flashing on the
display.
Selected band appears.
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
Note:
3 Tune in to a station you want while
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
“M” (manual) is still flashing.
To tune in to stations of
higher frequencies
2 Start searching for a station.
To search for stations of
higher frequencies
To tune in to stations of lower frequencies
• If you release your finger from the button,
the manual mode will automatically turns
off after 5 seconds.
• If you hold down the button, the frequency
keeps changing (in 50 kHz intervals for
FM and 9 kHz intervals for AM) until you
release the button.
To search for stations of lower frequencies
When a station is received, searching stops.
To stop searching before a station is
received, press the same button you have
pressed for searching.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2, or FM3).
These stations are preset in the number buttons
—No.1 (lowest frequency) to No.6 (highest
frequency).
When an FM stereo broadcast is hard to
receive:
Press MO (monaural), while
listening to an FM stereo broadcast.
Each time you press the button, the
MO indicator lights up and goes off
alternately.
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.
Manual preset
You can preset up to 6 stations in each band
(FM1, FM2, FM3, and AM) manually.
MO (monaural) indicator
When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved.
Ex.: Storing FM station of 92.5 MHz into the
preset number 1 of the FM1 band.
To restore the stereo effect, press the same
button again.
1 Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).
Storing stations in memory
You can use one of the following two methods to
store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strong-
station Sequential Memory)
2 Tune in to a station (in this example,
• Manual preset of both FM and AM stations
of 92.5 MHz).
To tune in to stations of
higher frequencies
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM
band (FM1, FM2, and FM3).
To tune in to stations of lower frequencies
1 Select the FM band (FM1 – 3) you
want to store FM stations into.
3 Press and hold the number button
(in this example, 1) for more than
2 seconds.
2 Press and hold both buttons for
more than 2 seconds.
Preset number flashes for a while.
CONTINUED ON THE NEXT PAGE
“SSM” appears, then disappears when
automatic preset is over.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Repeat the above procedure to store
other stations into other preset
numbers.
1 Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).
Notes:
• A previously preset station is erased when a new
station is stored in the same preset number.
• Preset stations are erased when the power supply to
the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset
the stations again.
2 Tune in to a station (in this example,
of 92.5 MHz).
Tuning in to a preset station
You can easily tune in to a preset station.
Remember that you must store stations first. If
you have not stored them yet, see “Storing
stations in memory” on pages 7 and 8.
3 Press and hold the button for more
than 2 seconds.
“P0” flashes on the display, showing that the
station has been preset.
1 Select the band (FM1 – 3, AM).
2 Select the number (1 – 6) for the
preset station you want.
Notes:
• A previously preset station is erased when a new
station is stored in the EX button.
• The preset station is erased when the power supply
to the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset
the station again.
Storing your favorite station in
to the one-touch operation
button (EX—extra)
To tune into the favorite station
The unit automatically turns on
(if it has been off).
Your favorite station is tuned
in—except when the tape is
playing.
• If you press the button again,
the last received station will be
tuned in.
You can preset an FM or AM station (such as
your favorite station or traffic announcement
station); and recall it by one touch operation even
if the unit is turned off.
Ex.: Storing an FM station of 92.5 MHz in to the
one-touch operation button (EX).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TAPE OPERATIONS
Listening to a cassette
You can play back type I (normal) tapes.
1 Turn on the power.
To stop play and eject the cassette
Press 0.
Tape play stops, the cassette automatically
ejects from the cassette compartment. The
source changes to the previously selected one.
• You cannot change the source if the cassette is
still in the cassette compartment.
To change the source, you must eject the
cassette first.
Note on One-Touch Operation:
• You can also eject the cassette by pressing 0
while the unit is turned off.
When a cassette is already in the cassette
compartment, tape play starts automatically.
However, it is not recommended to leave the
cassette in the compartment when turning off the
power. It may damage the tape head and the
cassette.
To fast wind a tape
2 Insert a cassette into the cassette
compartment.
When one side of the tape
reaches its end during
play, the other side of the
tape automatically starts
playing. (Auto Reverse)
Press in ¡ or 1.
The tape will be wound in the direction of the
arrows (
or
).
3 Select the tape direction.
Press both buttons at the
same time.
Tape direction
Each time you press both
buttons, the tape direction
changes alternately—
forward (
reverse (
) and
).
To restart playback, lightly press the other
button which is not pressed in (1 or ¡).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SOUND ADJUSTMENTS
Adjusting the sound
2 Adjust the level.
You can adjust the sound characteristics to your
preference.
To increase the level
1 Select the item you want to adjust.
Each time you press the
button, the adjustable
items change as follows:
To decrease the level
Ex.: When you select “TRE” (treble)
3 Repeat steps 1 and 2 to adjust the
other items.
Indication
To do:
Range
BAS
(Bass)
Adjust the bass.
–6 (min.)
|
+6 (max.)
Turning on/off the super bass
function
TRE
Adjust the treble. –6 (min.)
The super bass function allows you to maintain
the richness and fullness of the bass sound
regardless of how low you set the volume.
(Treble)
|
+6 (max.)
FAD*1
(Fader)
Adjust the front
and rear speaker
balance.
R6 (Rear only)
|
F6 (Front only)
Each time you press the
button, the function turns on
and off alternately.
BAL
Adjust the left
L6 (Left only)
(Balance) and right speaker
balance.
|
.
S BASS indicator
R6 (Right only)
VOL*2
Adjust the volume. 00 (min.)
(Volume)
|
50 (max.)
*1 If you are using a two-speaker system, set the fader
level to “00.”
*2 Normally, the + and – buttons work as the volume
control buttons. So you do not have to select “VOL”
to adjust the volume level.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting preset sound modes
1 Call up the sound mode you want to
adjust.
You can select a preset sound adjustment
suitable to the music genre.
• See on the left column for
details.
Select the sound mode you want.
Each time you press the button,
the sound mode changes as
follows:
2 To adjust the bass or treble level.
1 Select “BAS” (bass) or “TRE” (treble).
2 Adjust the level.
Ex.: When you select “BEAT”
Indication
For:
Preset values
BAS TRE S.BASS
SCM OFF (Flat sound) 00
00
00
OFF
ON
BEAT
Rock or
+2
disco music
SOFT
Quiet
background
music
+1
–3
+1
OFF
OFF
To turn on or off the super bass function.
• See page 10 for details.
POP
Light music
+4
Notes:
3 Repeat step 2 to adjust the other
• You can adjust each sound mode to your preference,
and store it in memory.
items.
If you want to adjust and store your original sound
mode, see “Storing your own sound adjustments”
below.
• To adjust the bass and treble reinforcement levels or
to turn on/off the super bass function, see page 10.
4 Press and hold SCM until the sound
mode you have selected in step 1
flashes on the display.
Your adjustment made for
the selected sound mode is
stored in memory.
Storing your own sound
adjustments
5 Repeat the same procedure to store
other sound modes.
You can adjust the sound modes (BEAT, SOFT,
POP) to your preference and store your own
adjustments in memory.
To reset to the factory settings, repeat the
same procedure and reassign the preset values
listed in the table on the left column.
• There is a time limit in doing the following
procedure. If the setting is canceled before you
finish, start from step 1 again.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DETACHING THE C0NTROL PANEL
You can detach the control panel when leaving
the car.
Attaching the control panel
When detaching or attaching the control panel,
be careful not to damage the connectors on the
back of the control panel and on the panel
holder.
1 Insert the left side of the control
panel into the groove on the panel
holder.
Detaching the control panel
Before detaching the control panel, be sure to
turn off the power.
1 Unlock the control panel.
2 Press the right side of the control
panel to fix it to the panel holder.
2 Lift and pull the control panel out of
the unit.
Note on cleaning the connectors:
If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened
with alcohol, being careful not to damage the
connectors.
3 Put the detached control panel into
the provided case.
Connectors
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
What appears to be trouble is not always serious. Check the following points before calling a service
center.
Symptoms
Causes
Remedies
• Sound cannot be heard
The volume level is set to the Adjust it to the optimum level.
from the speakers.
minimum level.
Connections are incorrect.
Check the cords and
connections.
• This unit does not work at
all.
The built-in microcomputer
may have functioned
While holding SEL, press
for more than 2
incorrectly due to noise, etc.
seconds to reset the unit. (Your
preset adjustments will also be
erased.) (See page 2.)
• SSM (Strong-station
Sequential Memory)
automatic preset does not
work.
Signals are too weak.
Store stations manually.
• Static noise while listening
to the radio.
The antenna is not connected Connect the antenna firmly.
firmly.
• A cassette tape cannot be
inserted.
You have tried to insert a
cassette in the wrong way.
Insert the cassette with the
exposed tape facing right.
• Cassette tapes become
hot.
This is not a malfunction.
The tape head is dirty.
• Tape sound is at very low
level and sound quality is
degraded.
Clean it with a head cleaning
tape.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
This unit requires very little attention, but you will
be able to extend the life of the unit if you follow
the instructions below.
To keep the tape clean
To clean the head
• Always store the cassettes in their storage
cases after use.
• Do not store cassettes in the following places:
– Subject to direct sunlight
– With high humidity
– At extremely hot temperatures
• Clean the heads after every 10 hours of use
using a wet-type head cleaning tape (available
at an audio store).
When the head becomes dirty, you may realize
the following symptoms:
– Sound quality is reduced.
– Sound level decreases.
– Sound drops out.
CAUTION:
• Do not play the cassettes with peeling labels;
otherwise, they can damage the unit.
• Tighten tapes to remove slack since loose tape
may become entangled with the mechanism.
• Do not leave a cassette in the cassette
compartment after use, as the tape may become
slack.
• Do not play dirty or dusty tapes.
• Do not touch the highly-polished head with any
metallic or magnetic tools.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
CASSETTE DECK SECTION
AUDIO AMPLIFIER SECTION
Maximum Power Output:
Wow & Flutter: 0.15% (WRMS)
Fast-Wind Time: 190 sec. (C-60)
Frequency Response: 50 Hz to 14 000 Hz
(Normal tape)
Front:
Rear:
45 W per channel
45 W per channel
Continuous Power Output (RMS):
Front:
17 W per channel into 4 Ω, 40 Hz
Signal-to-Noise Ratio: 52 dB
Stereo Separation: 40 dB
to 20 000 Hz at no more than
0.8% total harmonic distortion.
17 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
Rear:
GENERAL
Power Requirement:
Operating Voltage: DC 14.4 V
(11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature: 0°C to +40°C
Dimensions (W × H × D):
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:
Bass:
Treble:
10 dB at 100 Hz
10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:
Installation Size (approx.):
182 mm × 52 mm × 150 mm
Panel Size (approx.):
1.0 V/20 kΩ load (250 nWb/m)
188 mm × 58 mm × 11 mm
Mass (approx.):
TUNER SECTION
1.3 kg (excluding accessories)
Frequency Range:
FM:
AM:
87.5 MHz to 108.0 MHz
531 kHz to 1 602 kHz
[FM Tuner]
Usable Sensitivity:
11.3 dBf (1.0 µV/75 Ω)
Design and specifications are subject to change
without notice.
50 dB Quieting Sensitivity:
16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Capture Ratio: 2.0 dB
[AM Tuner]
Sensitivity: 20 µV
Selectivity: 35 dB
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
EN
© 2005 Victor Company of Japan, Limited
0105DTSMDTJEIN
Download from Www.Somanuals.com. All Manuals Search And Download.
KS-FX384/KS-F184
Installation/Connection Manual
GET0308-002A
[UI]
0105DTSMDTJEIN
EN
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at
JVC car audio dealers.
Parts list for installation and connection
The following parts are provided for this unit.
After checking them, please set them correctly.
A / B
C
D
E
Hard case/Control panel
Sleeve
Trim plate
Power cord
G
J
I
F
H
Lock nut (M5)
Rubber cushion
Handles
Washer (ø5)
Mounting bolt (M5 x 20 mm)
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Do the required electrical connections.
*1 When you stand the unit, be
careful not to damage the fuse
Bend the appropriate tabs to hold
the sleeve firmly in place.
on the rear.
Removing the unit
Before removing the unit, release the rear section.
Insert the two handles, then pull them as illustrated so
that the unit can be removed.
When using the optional stay
When installing the unit without using the sleeve
In a Toyota for example, first remove the car radio and install the unit in its place.
Fire wall
Stay (option)
* Not included for this unit.
Flat type screws (M5 x 8 mm)*
Bracket*
Dashboard
Screw (option)
Flat type screws (M5 x 8 mm)*
Pocket
Bracket*
Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer
Install the unit at an angle of less than 30˚.
screws are used, they could damage the unit.
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• This unit does not work at all.
* Have you reset your unit?
1
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.
• Maximum input of the speakers should be more than 45 W at the rear and 45 W at the front, with an impedance of 4 Ω to 8 Ω.
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
Heat sink
A
Typical Connections
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the unit.
To CD Changer—only for KS-FX384 (see diagram
)
Rear ground
terminal
1
15 A fuse
15
1
*
Not included for this unit
Ignition switch
Line out (see diagram
)
Antenna
terminal
Black
To metallic body or chassis of the car
3
Yellow*2
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
2
Red
To an accessory terminal in the fuse block
Fuse block
2
*
Before checking the operation of this unit prior to
Blue with white stripe
installation, this lead must be connected, otherwise
power cannot be turned on.
To the remote lead of other equipment or
automatic antenna if any (200 mA max.)
White with black
stripe
White
Gray with black stripe
Gray
Green with black stripe
Green
Purple with black stripe
Purple
Left speaker (front)
Right speaker (front)
Left speaker (rear)
Right speaker (rear)
Connections Adding Other Equipment
B
Amplifier
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.
• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused.
Rear speakers
Remote lead
Y-connector (not supplied for this unit)
JVC Amplifier
Remote lead (Blue with white stripe)
To the remote lead of other equipment or
automatic antenna if any
Signal cord (not supplied for this unit)
*3 Firmly attach the ground wire to the metallic body or to
the chassis of the car—to the place not coated with
paint (if coated with paint, remove the paint before
attaching the wire). Failure to do so may cause
damage to the unit.
Front speakers
CD Changer
Only for KS-FX384
Refer also to page 13 of the INSTRUCTIONS.
Connecting cord supplied for your CD changer
JVC CD changer
CAUTION:
• Before connecting the CD changer, make sure that the
unit is turned off.
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the
unit will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker
wiring in your car.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
|