9" Portable On-camera LCD Monitor
User Manual
Model:
HDSDI&HDMI, Waveform, Audio meter, Focus assist
DT-X91F
DT-X91H
DT-X91C
3GSDI&HDMI
HDMI
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
ꢀ Monitor
1. Please keep the signal terminals and the cooling vent away from knife-edge, metal or liquid in order to
avoid short-circuit and damage.
2. Please don't try to disassemble any parts of the monitor by yourself, which would probably damage the
monitor and do harm to human body, and it will cause the invalidation of product warranty.
3. Please don't touch the screen with your fingers, which would probably deface the screen.
4. Please don't press the screen; the LCD is extremely exquisite and flimsy.
ꢀ The power
Please use the provided power adapter or the battery recommended by the manufacturer in order to
avoid damage. For a third party power adapter, please make sure the voltage range, supplied power, and
polarity of power lead are fit.
Please disconnect the power cable or take off the battery under the following situations:
1. If you do not operate this monitor for a period of time;
2. If the power cable or power adaptor is damaged;
3. If the monitor housing is broken.
ꢀ Working Environment
1. Please don't lay this product on the unstable place.
2. Please don't lay this product in hot, cold or wet location.
ꢀ
Cleaning
1. Please clean the screen with dry and downy cloth or special LCD cleanser.
2. Please do not press hard when cleaning the screen.
3. Please do not use water or other chemical cleanser to clean the screen. The chemical may damage
the LCD.
4. For first time use, please tear off the factory LCD film. To protect the LCD screen, please post the LCD
protection film offered in the package.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Features
DT-X91F
High resolution 9” LCD Panel
Peaking focus assist (red/blue switch)
16:9, 1280×800, 16.77 million colors
Multiple inputs
The Peaking focus assist function is to mark the
sharpest edges of the image with red or blue color,
for users to check if the subjects are focused.
Zebra stripes
2 HD/SD-SDI, 1 HDMI and 1 Composite input.
Loop through outputs
2 HD/SD-SDI and 1 HDMI loop through output.
HDMI converted to SDI output
Zebra Stripes are used to check if the image is
over exposed or not by showing black and white
lines on the monitor. It is considered over exposed
when luminance value exceeds 90%.
False color
Supported HDMI formats: 480i / 576i / 720p (50,
59.94, 60) / 1080i (50, 59.94, 60) / 1080P (23.98
24, 25, 29.97, 30), and the output SDI will embed
the audio (48KHz) from HDMI.
The false color is used to aid in the setting of
camera exposure. Under false color mode, there’s
a false color key on the bottom of screen for
reference. The over exposed subjects (above 101
IRE) on the monitor will display as RED, and the
underexposed subjects will display as BLUE. For
correct exposed subjects, it will display as green
and pink.
Waveform (Y, Cb, Cr, R, G, B) and full scale
There are totally 6 kinds of waveform display,
available under both SDI and HDMI, to check the
Luminance (Y), Blue-difference (Cb),
Red-difference (Cr), Red (R), Green (G), Blue (B),
and the Y, Cb, Cr can be simultaneously displayed,
R, G, B can be simultaneously displayed, and
each of the waveforms can be set to full scale
display.
Blue Only
Under the Blue Only Mode, only the blue pixels
are used to generate the image, because hue and
saturation can be adjusted quicker and more
accurately.
Vector scope
The displayed vector scope pattern is available
under both SDI and HDMI, represents saturation
as distance from the center of the circle, and hue
as the angle, in standard position, around it.
Histogram (R, G, B)
DSLR scale zoom in
The Canon DSLR outputs the CMOS sensor ratio
HDMI and this zoom in mode can make the
effective image scale full screen on the monitor.
User definable function keys
The histogram is a bar graph that shows the
distribution of luminance values in the picture.
There’re R, G, B histograms that individually
displayed simultaneously, available under both
SDI and HDMI.
There are 3 function keys on the monitor front
panel, that permit users to define shortcuts for the
various functions.
16-ch audio meter
User editable video title
Under HDSDI, it displays 16 channels audio bars,
with mark, and under SDSDI or HDMI, it displays
2 channels audio bars with mark. The audio bar is
green, and will turn yellow when audio exceeds
-20dB, and turn red when exceeds -10dB.
SDI timecode
User can edit a video title for the current camera,
and the title will display on the top of screen.
Front and Rear 3-color TALLY light
2 TALLY lights design, to give “live” signals to
people in front of the camera, as well as the
camera operator behind.
Under SDI input, it can display the SMPTE
timecode, which is used extensively for
synchronization, and for logging and identifying
material in recorded media.
Image Flip
Set image to rotate by 180 .
Download from Www.Somanuals.com. All Manuals Search And Download.
DT-X91H
High resolution 9” LCD Panel
16:9, 1280×800, 16.77 million colors
3Gbps SDI support
DSLR scale zoom in
The Canon DSLR outputs the CMOS sensor ratio
HDMI and this zoom in mode can make the
effective image scale full screen on the monitor.
User definable function keys
Accepts 3G/HD/SD-SDI input.
Multiple inputs
1 3G/HD/SD-SDI, 1 HDMI, 1 Composite input
and L/R stereo audio.
There are 2 function keys on the monitor front
panel, that permit users to define shortcuts for the
various functions.
Loop through outputs
1 3G/HD/SD-SDI, 1 HDMI and 1 Composite
video loop through output.
User editable video title
User can edit a video title for the current camera,
and the title will display on the top of screen.
Front and Rear 3-color TALLY light
2 TALLY lights design, to give “live” signals to
people in front of the camera, as well as the
camera operator behind.
SDI/HDMI embedded audio output
Convert SDI/HDMI embedded audio to analog
and output via speaker or 3.5mm earphone jack
Image Flip.
Set image to rotate by 180
DT-X91C
High resolution 9” LCD Panel
16:9, 1280×800, 16.77 million colors.
Multiple inputs
Image Flip
Set image to rotate by 180 .
User definable function keys
1 HDMI, 1 Composite input
There are 2 function keys on the monitor front
panel, that permit users to define shortcuts for the
various functions.
and L/R stereo audio input.
Loop through outputs
1 HDMI and 1 Composite loop through output.
HDMI embedded audio output
User editable video title
User can edit a video title for the current camera,
and the title will display on the top of screen.
Front and Rear 3-color TALLY light
2 TALLY lights design, to give “live” signals to
people in front of the camera, as well as the
camera operator behind.
Convert HDMI embedded audio to analog and
output via speaker or 3.5mm earphone jack.
DSLR scale zoom in
The Canon DSLR outputs the CMOS sensor ratio
HDMI and this zoom in mode can make the
effective image scale full screen on the monitor.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Panel Instruction
Front view
DT-X91F
PHONE: Earphone jack, for SDI embedded audio, HDMI embedded audio monitoring
POWER: Power on/off
Connect with power cable, press the “POWER” and the power indicator is turned on and the monitor
will be switched on and get into normal working status. Press the “POWER” again, the indicator is
turned off and monitor is switched off.
Disconnect with power cable or battery if the monitor will not be used for a period of time.
SOURCE: Input signal selection, revolve the “ENTER” to select the input video signal.
F1: User definable function key 1
FOCUS: Peaking Focus Assist
Press “FOCUS” once, it will display the current peaking on/off status. Press “FOCUS” again to switch
on RED line focus assist, switch on BLUE line focus assist, and switch off in turn.
F.COLOR: False color
Press “F.COLOR” once, it will display the current false color on/off status. Press “F.COLOR” again to
switch on/off the false color mode.
DISPLAY: Display current settings
Press “Display” to display safety mark, title and the current input signal information
F2: User definable function key 2
F3: User definable function key 3
WAVEFORM: Display waveform
Press “WAVEFORM” once, it will display the waveform menu as:
Revolve “ENTER” to select a waveform display mode and turn it on.
The selected waveform will display on the screen.
VECTOR: Display vector scope
Press “VECTOR” to switched on/off the Vector scope
MENU: Press to enter Menu
ENTER: Select and Apply
Under menu system, revolve “ENTER” to adjust settings and press to apply; and out of menu system,
directly revolve “ENTER” to adjust volume.
TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Speaker: Output SDI, HDMI and Analog audio
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear view
DC 12V IN: Connect with DC12V 4-pin XLR power adapter.
TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Battery mount:
Connect with SSL-JVC50 battery (optional) to power the monitor.
SDI-OUT: HDMI converted to SDI output (BNC connector)
SDI LOOP1/2: HD/SD-SDI loop through output (BNC connector)
HDMI-IN: HDMI input
TALLY controlling port (RS-232): Terminal description is as follows:
Terminal
1
2
3
4
5
6
7
8
9
Description
Y
G
R
GND GND GND
The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting.
The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting.
The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting
HDMI-LOOP: HDMI loop through output
SDI IN1/2: HD/SD-SDI input (BNC connector)
CVBS-IN: Composite video input (BNC connector)
Input formats
Input
Supported formats
CVBS
PAL / NTSC
480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
720p (60 / 59.94 / 50)
HDMI
SDI
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
1080i (60 / 59.94 / 50)
1080p (30 / 29.97 / 25 / 24 / 23.98)
1080psf (30 / 29.97 / 25 / 24 / 23.98)
720p (60 / 59.94 / 50)
SMPTE-274M
SMPTE-RP211
SMPTE-296M
SMPTE-125M
ITU-R BT.656
480i (59.94)
576i (50)
Download from Www.Somanuals.com. All Manuals Search And Download.
DT-X91H
Front view
PHONE: Earphone jack, for SDI embedded audio, HDMI embedded audio and analog audio monitoring
POWER: Power on/off
Connect with power cable, press the “POWER” and the power indicator is turned on and after 10
seconds, the monitor will be switched on and get into normal working status. Press the “POWER”
again, the indicator is turned off and monitor is switched off.
Disconnect with power cable or battery if the monitor will not be used for a period of time.
CVBS: Press to switch the input signal to Composite video
HDMI: Press to switch the input signal to HDMI
SDI: Press to switch the input signal to SDI
SCAN: Overscan / Underscan switch
MENU: Press to enter Menu
F1: User definable function key 1
F2: User definable function key 2
RATIO: 16:9 and 4:3 switch
ZOOM: Picture Zoom-in
Press “ZOOM” to switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in.
DISPLAY: Display current settings
Press “Display” to display safety mark, title and the current input signal information
ENTER: Select and Apply
Under menu system, revolve “ENTER” to adjust settings and press to apply;
and out of menu system, directly revolve “ENTER” to adjust volume.
TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Speaker: Output SDI, HDMI and Analog audio
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear view
DC 12V IN: Connect with DC12V 4-pin XLR power adapter.
Battery mount: Connect with SSL-JVC50 battery (optional) to power the monitor.
CVBS IN: Composite video input (BNC connector)
SDI-LOOP: 3G/HD/SD-SDI loop through output (BNC connector)
SDI-IN: 3G/HD/SD-SDI input (BNC connector)
HDMI-LOOP: HDMI loop through output
HDMI-IN: HDMI input
TALLY controlling port (RS-232): terminal description is as follows:
Terminal
1
2
3
4
5
6
7
8
9
Description
Y
G
R
GND GND GND
The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting.
The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting.
The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting.
AUDIO L: Stereo audio left channel input (RCA connector)
AUDIO R: Stereo audio right channel input (RCA connector)
CVBS-LOOP: Composite video loop through output (BNC connector)
TALLY Light: Red, Green and Yellow 3-color TALLY indicator.
Input formats
Input
Supported formats
CVBS
PAL / NTSC
480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
720p (60 / 59.94 / 50)
HDMI
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
1080p (60 / 59.94 / 50)
1080i (60 / 59.94 / 50)
1080p (30 / 29.97 / 25 / 24 / 23.98)
1080psf (30 / 29.97 / 25 / 24 / 23.98)
720p (60 / 59.94 / 50)
SMPTE-425M
SMPTE-274M
SDI
SMPTE-RP211
SMPTE-296M
SMPTE-125M
ITU-R BT.656
480i (59.94)
576i (50)
Download from Www.Somanuals.com. All Manuals Search And Download.
DT-X91C
Front view
PHONE: Earphone jack, for HDMI embedded audio and analog audio monitoring
POWER: Power on/off
Connect with power cable, press the “POWER” and the power indicator is turned on and after 10
seconds, the monitor will be switched on and get into normal working status. Press the “POWER”
again, the indicator is turned off and monitor is switched off.
Disconnect with power cable or battery if the monitor will not be used for a period of time.
CVBS: Press to switch the input signal to Composite video
HDMI: Press to switch the input signal to HDMI
B/W: Black and White mode
SCAN: Overscan / Underscan switch
MENU: Press to enter Menu
F1: User definable function key 1
F2: User definable function key 2
RATIO: 16:9 and 4:3 switch
ZOOM: Picture Zoom-in
Press “ZOOM” to switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in.
DISPLAY: Display current settings
Press “Display” to display safety mark, title and the current input signal information
ENTER: Select and Apply
Under menu system, revolve “ENTER” to adjust settings and press to apply;
and out of menu system, directly revolve “ENTER” to adjust volume.
TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Speaker: Output HDMI and Analog audio
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear view
DC 12V IN: Connect with DC12V 4-pin XLR power adapter.
Battery mount:
Connect with SSL-JVC50 battery (optional) to power the monitor.
CVBS IN: Composite video input (BNC connector)
HDMI-LOOP: HDMI loop through output
HDMI-IN: HDMI input
TALLY controlling port (RS-232): terminal description is as follows:
Terminal
1
2
3
4
5
6
7
8
9
Description
Y
G
R
GND GND GND
The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting.
The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting.
The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting
AUDIO L: Stereo audio L input (RCA connector)
AUDIO R: Stereo audio R input (RCA connector)
CVBS-LOOP: Composite video loop through output (BNC connector)
TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Input formats
Input
Supported formats
CVBS
PAL / NTSC
480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
HDMI
720p (60 / 59.94 / 50)
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Menu Operation
Press “MENU” and it will display menu system
ꢁ
ꢁ
ꢁ
ꢁ
Revolve “OK” to select an item. The selected item will be highlighted display.
Press “OK” to enter the selected item.
Under menu system, press “MENU” to back to previous menu.
The menu will automatically save and quit if it remains idle.
4. Picture Settings Submenu
The Picture Settings Submenu includes:
CONTRAST: 0-100 value adjustment
BRIGHTNESS: 0-100 value adjustment
HUE: 0-100 value adjustment
(Only available under Composite input)
SATURATION: 0-100 value adjustment
SHARPNESS: 0-100 value adjustment
5. System Configuration Submenu
The System Configuration Submenu includes:
RATIO: Select “16:9” or “4:3” to adjust the aspect ratio.
SCAN: “UNDERSCAN” / “OVERSCAN” selection
ZOOM: “OFF”, “ZOOM1” and “ZOOM2” selection
ZOOM1: Canon DSLR scale zoom-in
ZOOM2: Pixel to Pixel zoom-in
MARKER: Select and set the safety mark
scale from 80%, 85%, 90% and 95%.
FLIP: Select “YES” to flip the image by 180 .
RESET: Revolve “OK” to RESET and press to
recover all to factory setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
6. OSD Settings Submenu
The OSD Settings Submenu includes:
LANGUAGE: Menu language English / Chinese selection
H-POSITION: Menu horizontal position (0-100) adjustment, real-time preview, default value: 50, center.
V-POSITION: Menu vertical position (0-100) adjustment, real-time preview, default value: 50, center.
DURATION: Menu timeout setting
Set a time (in seconds) in which the menu
will automatically quit if remains idle.
Default: 10 seconds; Range: 5 seconds to
60 seconds.
7. Title Settings Submenu
Revolve "OK" button to select the letters, and press "OK" to input. Select SPACE to input space and DEL to
delete the left letter. Max 10 letters are supported.
After setting, press "MENU", the system will
save data to current user and quit menu. The
menu will automatically save and quit if it
remains idle.
8. Display Settings Submenu
The DISPLAY settings submenu is to select the
items to be displayed on screen when
‘DISPLAY” button is pressed. Revolve "OK" to
turn on/off the items:
(1) INFO: Including Input format, aspect ratio,
underscan/overscan, zoom status
(2) MARKER: Safety mark
(3) TITLE: User edited title
(4) MARKER4:3: The 4:3 scale mark on 16:9
image. (Only available under HD input)
Download from Www.Somanuals.com. All Manuals Search And Download.
9. FUNCTION KEY Settings Submenu
The F KEY Settings Submenu is to define Function Keys on the front keyboard.
The DT-X91F has 3 function keys:
F1, F2 and F3;
The DT-X91H and DT-X91C has 2 function keys:
F1 and F2.
The available function items of each model are:
-------------------DT-X91F-------------------
01-RATIO: Aspect ratio switch
-------------------DT-X91H-------------------
01-RATIO: Aspect ratio switch
02-SCAN: Underscan / Overscan switch
03-ZOOM: Picture Zoom-in
02-SCAN: Underscan / Overscan switch
03-ZOOM: Picture Zoom-in
04-B/W: Color / Black & white switch
05-BLUE ONLY: Blue only mode switch on/off
06-ZEBRA: Zebra over exposure switch on/off
07-VECTOR: Vector scope switch on/off
08-PATTERN: Internal colorbar switch on/off
09-RGB HIST: R, G, B Histogram switch on/off
10-TIMECODE: SDI timecode display switch on/off
11-F.COLOR: False color mode switch on/off
12-AUDIO BAR: Audio meter display switch on/off
13-FOCUS: Peaking focus assist switch on/off, and
red/blue selection
04-B/W: Color / Black & white switch
05-FLIP: Image flip
-------------------DT-X91C-------------------
01-RATIO: Aspect ratio switch
02-SCAN: Underscan / Overscan switch
03-ZOOM: Picture Zoom-in
04-B/W: Color / Black & white switch
05-FLIP: Image flip
14-FLIP: Image flip
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Specifications
LCD Performance
Size
9.0 inches
Resolution
Aspect ratio
Color system
Brightness
Contrast
1280 RGB 800
16:9/4:3
NTSC/PAL
250cd/m2
700:1
Color
16.77 million colors
H/V:140/120
Viewing angle
Video Format
SMPTE-425M **
1080p (60 / 59.94 / 50)
1080i (60 / 59.94 / 50)
SMPTE-274M
1080p (30 / 29.97 / 25 / 24 / 23.98)
1080psf (30 / 29.97 / 25 / 24 / 23.98)
720p (60 / 59.94 / 50)
SDI *
SMPTE-RP211
SMPTE-296M
SMPTE-125M
ITU-R BT.656
480i (59.94)
576i (50)
480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
HDMI
720p (60 / 59.94 / 50)
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
General
Working voltage
DC/ Battery 6.5V-17V
DT-X91F
DT-X91H
DT-X91C
18W
16W
12W
Power consumption
Working temperature
Working humidity
Storage temperature
Storage humidity
Dimensions
0
+40
10% 90%
-15 +60
10% 90%
236 171 48mm
970g
Net weight
* DT-X91C doesn’t support SDI input;
** Only DT-X91H support SMPTE-425M format.
11. Packing List
1. Monitor
1
1
1
1
1
1
1
2. User Manual
3. Power adaptor
4. Power cable
5. Sun hood
6. Screw ball head
7. LCD protection film
Download from Www.Somanuals.com. All Manuals Search And Download.
This model is manufactured, warranted and supported by SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC,
and distributed in North America by JVC Professional Video Products.
To obtain service or for further information, please contact:
SWIT Electronics USA, LLC.
Address: 4300 Stevens Creek Blvd., Suite 230, San Jose, CA 95129
Toll free: 1 866 986-SWIT (7948) • Tel: 408 260-8258 Fax: 408 228-8438
Version: 130308
Download from Www.Somanuals.com. All Manuals Search And Download.
|