JVC Camcorder GR AX655 User Manual
COMPACT VHS CAMCORDER  
GR-AX655  
Compact VHS  
For Customer Use:  
Enter below the Serial Nos. of the  
GR-AX655U camcorder and the  
AA-V11U AC Power Adapter/Charger.  
The serial numbers are located on the  
bottom of the GR-AX655U, and the  
AA-V11U.  
Model No.  
GR-AX655U  
AA-V11U  
INSTRUCTIONS  
Serial No.  
YU30052-602  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
5. Ventilation  
IMPORTANT PRODUCT  
SAFETY INSTRUCTIONS  
Slots and openings in the cabinet are provided for  
ventilation. To ensure reliable operation of the product and  
to protect it from overheating, these openings must not be  
blocked or covered.  
Electrical energy can perform many useful functions. But  
improper use can result in potential electrical shock or fire  
hazards. This product has been engineered and  
• Do not block the openings by placing the product on a  
bed, sofa, rug or other similar surface.  
• Do not place the product in a built-in installation such as  
a bookcase or rack unless proper ventilation is provided  
or the manufacturer’s instructions have been adhered to.  
manufactured to assure your personal safety. In order not to  
defeat the built-in safeguards, observe the following basic  
rules for its installation, use and servicing.  
6. Wall or Ceiling Mounting  
The product should be mounted to a wall or ceiling only as  
recommended by the manufacturer.  
ATTENTION:  
Follow and obey all warnings and instructions marked on  
your product and its operating instructions. For your safety,  
please read all the safety and operating instructions before  
you operate this product and keep this manual for future  
reference.  
ANTENNA INSTALLATION  
INSTRUCTIONS  
1. Outdoor Antenna Grounding  
INSTALLATION  
1. Grounding or Polarization  
If an outside antenna or cable system is connected to the  
product, be sure the antenna or cable system is grounded  
so as to provide some protection against voltage surges and  
built-up static charges. Article 810 of the National Electric  
Code, ANSI/NFPA 70, provides information with regard to  
proper grounding of the mast and supporting structure,  
grounding of the lead-in wire to an antenna discharge unit,  
size of grounding conductors, location of antenna  
discharge unit, connection to grounding electrodes, and  
requirements for the grounding electrode.  
(A) Your product may be equipped with a polarized  
alternating-current line plug (a plug having one blade  
wider than the other). This plug will fit into the power  
outlet only one way. This is a safety feature.  
If you are unable to insert the plug fully into the outlet,  
try reversing the plug. If the plug should still fail to fit,  
contact your electrician to replace your obsolete  
outlet. Do not defeat the safety purpose of the  
polarized plug.  
2. Lightning  
For added protection for this product during a lightning  
storm, or when it is left unattended and unused for long  
periods of time, unplug it from the wall outlet and  
disconnect the antenna or cable system. This will prevent  
damage to the product due to lightning and power-line  
surges.  
(B) Your product may be equipped with a 3-wire  
grounding-type plug, a plug having a third (grounding)  
pin. This plug will only fit into a grounding-type power  
outlet. This is a safety feature.  
If you are unable to insert the plug into the outlet,  
contact your electrician to replace your obsolete  
outlet. Do not defeat the safety purpose of the  
grounding-type plug.  
3. Power Lines  
An outside antenna system should not be located in the  
vicinity of overhead power lines or other electric light or  
power circuits, or where it can fall into such power lines or  
circuits. When installing an outside antenna system,  
extreme care should be taken to keep from touching such  
power lines or circuits as contact with them might be fatal.  
2. Power Sources  
Operate your product only from the type of power source  
indicated on the marking label. If you are not sure of the  
type of power supply to your home, consult your product  
dealer or local power company. If your product is intended  
to operate from battery power, or other sources, refer to the  
operating instructions.  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70  
3. Overloading  
Do not overload wall outlets, extension cords, or integral  
convenience receptacles as this can result in a risk of fire or  
electrical shock.  
ANTENNA  
LEAD IN WIRE  
GROUND CLAMP  
4. Power Cord Protection  
Power supply cords should be routed so that they are not  
likely to be walked on or pinched by items placed upon or  
against them, paying particular attention to cords at plugs,  
convenience receptacles, and the point where they exit  
from the product.  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION  
810-20)  
ELECTRIC SERVICE  
EQUIPMENT  
GROUNDING  
CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
POWER SERVICE GROUNDING ELECTRODE SYSTEM  
(NEC ART 250. PART H)  
NEC – NATIONAL ELECTRICAL CODE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
USE  
SERVICING  
1. Servicing  
1. Accessories  
To avoid personal injury:  
If your product is not operating correctly or exhibits a  
marked change in performance and you are unable to  
restore normal operation by following the detailed  
procedure in its operating instructions, do not attempt to  
service it yourself as opening or removing covers may  
expose you to dangerous voltage or other hazards. Refer all  
servicing to qualified service personnel.  
• Do not place this product on an unstable cart, stand,  
tripod, bracket or table. It may fall, causing serious injury  
to a child or adult, and serious damage to the product.  
• Use only with a cart, stand, tripod, bracket, or table  
recommended by the manufacturer or sold with the  
product.  
• Use a mounting accessory recommended by the  
manufacturer and follow the manufacturer’s instructions  
for any mounting of the product.  
2. Damage Requiring Service  
Unplug this product from the wall outlet and refer servicing  
to qualified service personnel under the following  
conditions:  
• Do not try to roll a cart with small casters across  
thresholds or deep-pile carpets.  
a. When the power supply cord or plug is damaged.  
b. If liquid has been spilled, or objects have fallen into the  
product.  
2. Product and Cart Combination  
A product and cart combination should be moved with  
care. Quick stops, excessive force, and uneven surfaces  
may cause the product and cart combination to overturn.  
c. If the product has been exposed to rain or water.  
d. If the product does not operate normally by following  
the operating instructions. Adjust only those controls that  
are covered by the operating instructions as an improper  
adjustment of other controls may result in damage and  
will often require extensive work by a qualified  
technician to restore the product to its normal operation.  
e. If the product has been dropped or damaged in any way.  
f. When the product exhibits a distinct change in  
performance—this indicates a need for service.  
3. Water and Moisture  
PORTABLE CART WARNING  
(Symbol provided by RETAC)  
Do not use this product near  
water—for example, near a bath  
tub, wash bowl, kitchen sink or  
laundry tub, in a wet basement, or  
near a swimming pool and the  
like.  
3. Replacement Parts  
When replacement parts are required, be sure the service  
technician has used replacement parts specified by the  
manufacturer or have the same characteristics as the  
original part. Unauthorized substitutions may result in fire,  
electric shock or other hazards.  
4. Object and Liquid Entry  
Never push objects of any kind into this product through  
openings as they may touch dangerous voltage points or  
short-out parts that could result in a fire or electric shock.  
Never spill liquid of any kind on the product.  
4. Safety Check  
Upon completion of any service or repairs to this product,  
ask the service technician to perform safety checks to  
determine that the product is in safe operating condition.  
5. Attachments  
Do not use attachments not recommended by the  
manufacturer of this product as they may cause hazards.  
6. Cleaning  
Unplug this product from the wall outlet before cleaning.  
Do not use liquid cleaners or aerosol cleaners. Use a damp  
cloth for cleaning.  
7. Heat  
The product should be situated away from heat sources  
such as radiators, heat registers, stoves, or other products  
(including amplifiers) that produce heat.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QUICK OPERATION GUIDE  
5
SUPPLY POWER  
INSERTING A VIDEO  
CASSETTE  
Hook on.  
1
EJECT  
1
Push in.  
2
3
PUSH  
2
Insert.  
BATT. RELEASE  
Using the battery pack  
1 Hook-on the battery pack's top end to the  
camcorder. (Charging procedure, ੬ P. 8)  
2 Push in the battery pack until it locks into  
place.  
1 Slide EJECT.  
2 Insert a video cassette.  
3 Press PUSH.  
(For more details, ੬ P. 11)  
To remove the battery pack  
Slide BATT. RELEASE and pull out the battery  
pack.  
PLAYBACK  
SHOOTING  
PLAY/PAUSE  
3
REW  
2
1
LENS COVER  
open/close knob  
2
Set to “CAMERA”  
STOP  
Recording Start/Stop button  
3
1
Set to “PLAY”  
1 Set the power switch to “PLAY”.  
2 Press REW.  
1 Slide the LENS COVER open/close knob to  
open the lens cover.  
2 Set the power switch to “CAMERA”.  
— The power indicator will light and an  
image will appear in the viewfinder.  
3 Press the Recording Start/Stop button.  
— Recording starts.  
— The tape will automatically stop at the  
beginning of the tape.  
3 Press PLAY/PAUSE.  
— Playback starts and the playback picture  
appears in the viewfinder.  
•To stop playback, press STOP.  
(For more details, ੬ P. 30.)  
•To stop recording temporarily, momentarily  
press the Recording Start/Stop button once  
again.  
(For more details, ੬ P. 14)  
Ⅲ Or simply play back the tape on a VHS  
VCR using the Cassette Adapter  
(VHS Playpak). ੬ P. 28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAJOR FEATURES  
6
REMEMBER  
Intelligent Function Control  
(੬ P. 18 – 25)  
The Logical Choice  
F1  
SEL  
F2  
The only compact video  
cassettes that can be  
Variable-Speed Hyper Zoom  
(੬ P. 15)  
used with your VHS VCR*  
Zoom-in  
T
T
T
T
Program AE with Special  
W
W
W
W
Effects (੬ P. 16)  
Zoom-out  
Ⅲ Auto Mode Lock  
Ⅲ Auto Mode Release  
Ⅲ Electronic Fog Filter  
Ⅲ ND Effect  
Ⅲ Sepia  
Ⅲ Twilight  
Random Assemble Editing  
(੬ P. 32 – 35)  
Ⅲ Sports  
2
8
5
4
1
6
3
7
Ⅲ High Speed (1/2000 sec.) Shutter  
Ⅲ 15 sec. Self Timer  
1
2
3
4
5
6
7
8
Integrated Auto Light  
(੬ P. 18)  
PROVIDED ACCESSORIES  
•AC Power  
Adapter/Charger  
AA-V11U  
•Battery Pack  
BN-V11U  
•Cassette Adapter  
(VHS PlayPak)  
C-P7U  
•Shoulder Strap •Lithium Battery  
Cassettes marked  
can be used with this camcorder.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
7
GETTING STARTED  
8
Power ..................................................................................... 8  
Clock (Lithium) Battery Removal/Insertion........................................ 10  
Date/Time Settings ................................................................... 10  
Viewfinder Adjustment ............................................................... 11  
Tape Length/Recording Mode Setting .............................................. 11  
Loading/Unloading A Cassette ...................................................... 11  
Grip Adjustment ....................................................................... 12  
Shoulder Strap Attachment........................................................... 12  
Tripod Mounting ....................................................................... 12  
Remote Control Unit RM-V700U (optional) ....................................... 13  
RECORDING  
14  
Basic Recording ........................................................................ 14  
Basic Features ......................................................................... 15  
Advanced Features .................................................................... 16  
PLAYBACK  
28  
Using The Cassette Adapter.......................................................... 28  
Basic Connections...................................................................... 29  
Basic Playback ......................................................................... 30  
Features ................................................................................ 31  
EDITING  
32  
Tape Dubbing........................................................................... 32  
Random Assemble Editing (R.A.Edit)................................................ 32  
Insert Editing ........................................................................... 36  
Audio Dubbing ......................................................................... 37  
USER MAINTENANCE  
TROUBLESHOOTING  
INDEX  
38  
39  
40  
Controls................................................................................. 40  
Connectors.............................................................................. 40  
Indicators ............................................................................... 40  
Other Parts............................................................................. 40  
Viewfinder ............................................................................. 41  
Terms .................................................................................... 42  
CAUTIONS  
43  
45  
45  
46  
48  
49  
SPECIFICATIONS  
OPTIONAL ACCESSORIES  
ESPAÑOL  
FOR SERVICING  
WARRANTY  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GETTING STARTED  
8
Power  
This camcorder’s 3-way power supply system lets you  
choose the most appropriate source of power.  
NOTES:  
● No function is available without power supply.  
● Use only specified power supply.  
● Do not use provided power supply units with other equipment.  
CHARGING THE BATTERY PACK  
CHG. (charge) indicator  
Marks  
SUPPLY POWER  
Connect the charger’s AC power cord to a wall  
POWER  
indicator  
1
2
outlet. The power indicator lights.  
To AC outlet  
ATTACH BATTERY PACK  
Align the marks and slide the battery pack in the  
direction of the arrow until it locks in place.  
The CHG. indicator lights.  
END  
indicator  
DETACH BATTERY PACK  
When charging is completed, the END indicator  
lights. Slide the battery pack opposite the direction  
of the arrow.  
3
BATT. PACK  
CHARGE  
DISCHARGE  
REFRESH switch  
REFRESH indicator  
approx.  
3 hrs. 30 min.  
BN-V11U  
BN-V12U  
approx. 1 hr. 10 min.  
approx.  
3 hrs. 30 min.  
approx. 1 hr. 10 min.  
BN-V22U  
BN-V25U  
approx. 2 hrs. 10 min.  
approx. 2 hrs. 40 min.  
approx. 7 hrs.  
approx. 10 hrs.  
USING THE BATTERY PACK  
Hook on.  
ATTACH BATTERY PACK  
Hook its top end to the camcorder and push the  
battery pack in until it locks in place.  
1
2
DETACH BATTERY PACK  
Slide BATT. RELEASE and pull out the battery pack.  
Push in.  
BATT. RELEASE  
RECORDING TIME  
BATT. PACK  
light off  
light on  
approx. 35 min.  
approx. 35 min.  
BN-V11U  
BN-V12U  
BN-V22U  
BN-V25U  
approx. 1 hr.  
approx. 1 hr.  
**REFRESH  
approx. 2 hrs. 10 min. approx. 1 hr. 20 min.  
approx. 2 hrs. 50 min. approx. 1 hr. 50 min.  
The AC power adapter features a REFRESH  
function that allows you to fully discharge the  
battery pack before recharging.  
To discharge the battery . . .  
.... attach the battery pack to the adapter as  
shown in the illustration to the left. Then  
push REFRESH. The REFRESH indicator  
lights when discharging starts, and goes  
out when discharging is complete.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
**CHARGE MARKER  
A charge marker is provided on the battery pack to  
help you remember whether it has been charged or  
not. Two colors are provided (red and black)—you  
choose which one means charged and which  
means discharged.  
Charge marker  
NOTES:  
● The recording time per charge is affected by such factors as the time spent in Record/Standby mode and  
the frequency of zooming. It is safer to have spare battery packs.  
● Charging times noted on page 8 are for fully discharged battey pack, and discharging times are for fully  
charged battery pack.  
● Charging and discharging times vary according to the ambient temperature and the status of the battery  
pack.  
● Remember to set the charge marker after charging a battery pack or after detaching a discharged one from  
your camcorder.  
● Perform the REFRESH function after no less than 5 chargings.  
● High temperatures can damage the battery pack, so use only where good ventilation is available. Don’t  
allow it to discharge in container, such as a bag.  
● If you stop recharging or discharging part way through, make sure to remove the battery pack before  
unplugging the adapter’s AC cord.  
● Remove the battery pack from the adapter immediately after discharging.  
● To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.  
● Make sure you unplug the DC cord before charging or discharging the battery pack.  
● A blinking CHG. indicator means that the battery pack has become hot. Wait until it cools down to  
continue.  
● The CHG. indicator may not light properly with a brand new battery pack, or with one that’s been stored  
for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHG.  
indicator should light during recharging. If not, contact your nearest JVC dealer.  
USING A CAR BATTERY  
Use the optional Car Battery Cord or Car Battery  
Charger/Adapter (connect as shown in the  
illustration to the left).  
To AC outlet  
DC OUT terminal  
NOTES:  
● When using the car battery, leave the engine  
idling.  
● The optional Car Battery Charger (BH-V3U) can  
also be used to charge the battery pack.  
● When using the optional Car Battery Charger or  
Car Battery Cord (AP-V7U), refer to the respective  
instruction booklet.  
AC Power  
Adapter/Charger  
AA-V11U  
DC cord  
To car's  
cigarette  
lighter  
Car Battery Cord  
AP-V7U (optional)  
USING AC POWER  
Use the AC Power Adapter (connect as shown in  
the illustration to the left).  
socket  
NOTE:  
The supplied AC Power Adapter/Charger features  
automatic voltage selection in the AC range from  
110 V to 240 V.  
Car Battery Charger/Adapter  
BH-V3U (optional)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GETTING STARTED (cont.)  
10  
Clock (Lithium) Battery Removal/Insertion  
A
This battery is necessary for clock operation and to  
perform date/time settings.  
SWITCH OFF POWER  
Switch off the unit’s power and remove the power  
1
2
supply unit.  
OPEN COVER  
Open the clock battery compartment cover while  
pressing the release tab.  
REMOVE BATTERY (when replacing)  
Insert a pointed, non-metallic object between the  
3 battery and the compartment (  
A
) and pull the  
battery out.  
INSERT BATTERY  
Ensuring the plus (+) side is up, insert the supplied  
lithium battery and push it in.  
4
5
–/+  
SET  
CLOSE COVER  
Close the compartment cover until it clicks in place.  
NOTE:  
See “SAFETY PRECAUTIONS”(੬ pg. 2) for information  
on safe handling of lithium batteries.  
Date/Time Settings  
SELECT MODE  
Set the power switch to CAMERA.  
1
POWER  
SET DATE/TIME  
Press SET and the month blinks. Press + or – to set  
2
3
the month. Repeat to set day, year, hour and minute.  
Date  
Month/Day/Year  
DATE ... Date setting is performed  
START CLOCK  
Press SET. The blinking stops. The date and time are  
both displayed for confirmation, then the time  
display disappears.  
NOTE:  
DATE JAN 1.00  
TIME AM12:00  
The clock does not keep time while the date and time are  
blinking.  
Time  
12-hour indication with AM or PM  
TIME .... Time setting is performed  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Viewfinder Adjustment  
SP-EP recording mode and  
T20•30•40 tape length select button  
POSITION VIEWFINDER  
Adjust the viewfinder manually for best viewability  
(see illustration at left).  
1
2
3
SELECT MODE  
Set the power switch to CAMERA.  
ADJUST DIOPTER  
Turn the diopter adjustment control until the  
indications in the viewfinder are clearly focused.  
Tape Length/Recording Mode Setting  
SET TAPE LENGTH  
Set the tape length button according to the length of  
the tape used. T20 = 20 minutes of recording time,  
T30 = 30 minutes, and T40 = 40 minutes (in SP).  
1
2
SET RECORDING MODE  
Set POWER to "CAMERA".  
Set depending on your preference. “SP” (Standard  
Play) provides higher picture and sound quality and  
is better for dubbing, while “EP” (Extended Play) is  
more economical, recording at 1/3 the speed of SP.  
Tape length and recording  
mode indicator  
T30 SP  
T20 SP  
T40 EP  
T40 SP  
T20 EP  
T30 SP  
T30 EP  
Loading/Unloading A Cassette  
OPEN CASSETTE HOLDER  
Slide EJECT until the holder opens. Do not use force  
1
2
3
to open.  
INSERT/REMOVE CASSETTE  
Make sure the label is facing outward.  
CLOSE CASSETTE HOLDER  
Press PUSH and make sure the holder is closed and  
locked.  
NOTES:  
● A cassette holder can’t be opened unless a power  
supply is attached.  
● Make sure that the tape is not slack when loading the  
cassette. If there is any slack, turn the gear on the  
cassette in the direction of the arrow to take up the  
slack.  
● Make sure the Erase Protection tab is present. If not,  
cover the hole with adhesive tape. (Some cassettes  
have sliding tabs – in this case, check the tab's  
position.)  
Turn to take up  
slack.  
Erase Protection  
Gear  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GETTING STARTED (cont.)  
Grip Adjustment  
12  
EXPAND LOOP  
Separate the Velcro strip.  
1
2
3
INSERT HAND  
Pass your right hand through the loop and grasp the  
grip.  
ADJUST STRAP LENGTH  
Adjust so your thumb and fingers can easily operate  
the Recording Start/Stop button and Power Zoom  
switch. Refasten the Velcro strip.  
Recording Start/Stop button  
Shoulder Strap Attachment  
ATTACH STRAP  
Following the illustration at left, thread the strap  
1
through the top of the eyelet (1), then fold it back  
and thread it through the keeper (2), and then  
through the buckle (3). Repeat the procedure to  
attach the other end of the strap to the other eyelet,  
making sure the strap isn’t twisted.  
1
3
2
2
1
ADJUST LENGTH  
Adjust as shown in the illustration at left (1), then  
slide both keepers snug against the eyelets to  
prevent slipping (2).  
2
Tripod Mounting  
ALIGN AND TIGHTEN  
Align the screw and camera direction stud on the  
tripod with the camera’s mounting socket and stud  
hole. Then tighten the screw.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Remote Control Unit RM-V700U (optional)  
The RM-V700U Full-Function Remote Control Unit can  
operate this camcorder from a distance as well as the  
basic operations (PLAY, STOP, PAUSE, FF, and REW) of  
your VCR. This remote control unit makes additional  
recording functions possible. To operate, point it at the  
camcorder’s remote sensor.  
Infrared beam  
effective area  
10°  
Infrared beam  
sensor window  
PULL OUT BATTERY HOLDER  
10°  
Pull out the battery holder according to the type of  
The transmitted beam may not be effective or  
may cause misoperations when the infrared  
beam sensor window is directly exposed to  
sunlight or powerful lighting.  
1
2
remote control unit you have.  
A
Type : Pull out the battrery holder while sliding  
the lock hole.  
B
Type : Pinch the release tab and pull out the  
battery holder.  
1
2
0
!
@
INSERT BATTERY  
Insert the lithium battery* (CR2025), with its plus (+)  
side up, into the battery holder.  
3
4
5
REPLACE BATTERY HOLDER  
Replace the battery holder until it clicks in place.  
3
*Read warning on lithium battery. (੬ pg. 2)  
6
7
8
9
#
$
%
^
A
B
&
Lock hole  
Release tab  
Functions  
Buttons  
With the camcorder’s power switch set to  
With the camcorder’s power switch set to  
“PLAY”.  
“CAMERA”.  
1 PAUSE IN connector  
—
੬ pg. 34  
2 Infrared beam  
transmitting window  
Transmits the beam signal.  
3 MBR SET button  
4 INT. TIME button  
5 REC TIME button  
6 FF button  
7 REW button  
8 PAUSE button  
—
Self-Timer/Time lapse (੬ pg. 26, 27)  
Animation/Time lapse (੬ pg. 27)  
Retake (Forward) (੬ pg. 15)  
Retake (Rewind) (੬ pg. 15)  
—
੬ pg. 33  
—
—
FF/FF Shuttle Search (੬ pg. 31)  
Rew/Rew Shuttle Search (੬ pg. 31)  
Pause (੬ pg. 31)  
9 PLAY button  
0 START/STOP button  
! VISS button  
—
Playback start (੬ pg. 30)  
Functions same as the Recording Start/Stop button of the camcorder.  
Index code marking (੬ pg. 15)  
—
@ ZOOM (T/W) button  
# VCR CTL button  
$ A. DUB button  
% STOP button  
^ INSERT button  
& R. A. EDIT button  
Zoom (invariable speed (੬ pg. 15)  
—
—
—
—
—
—
੬ pg. 33  
Audio dubbing (੬ pg. 37)  
Stop (੬ pg. 30)  
Insert Editing (੬ pg. 36)  
੬ pg. 34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING Basic Recording  
14  
NOTE:  
LENS COVER  
SWITCH  
You should already have performed the procedures listed  
below. If not, do so before continuing.  
● Power (੬ pg. 8)  
● Tape Length/Recording Mode Setting (੬ pg. 11)  
● Grip Adjustment (੬ pg. 12)  
LOAD A CASSETTE  
Slide EJECT to open the cassette holder, then insert  
the cassette with the label facing out. Press PUSH to  
ensure the holder is closed and locked.  
1
2
ENTER RECORD–STANDBY MODE  
Slide the LENS COVER open/close switch to open  
the lens cover, then set the power switch to  
CAMERA.  
POWER  
Start/Stop  
•The power indicator lights and the camcorder  
enters the Record–Standby Mode.  
•The scene you’re aimed at appears on the  
viewfinder screen, with the word “PAUSE”  
superimposed upon it.  
The power indicator  
START SHOOTING  
Press the Recording Start/Stop button.  
3
4
Tape remaining time  
indicator  
•The tally lamp lights while recording is in progress,  
REC  
and “  
” appears in the viewfinder.  
120MIN  
119MIN  
3MIN  
1MIN (Blinking)  
0MIN (Blinking)  
2MIN (Blinking)  
STOP RECORDING  
Press the Recording Start/Stop button again to stop  
recording.  
*
MIN.....(Now calculating)  
•The camcorder re-enters the Record-Standby  
mode.  
NOTES:  
● A cassette holder can’t be opened unless a power  
supply is attached.  
● There may be a delay after you slide EJECT until the  
holder opens. Do not use force.  
● The tape’s remaining time is displayed in the  
viewfinder as shown.  
● ”TAPE END“ appears when the tape reaches its end,  
and the power goes off automatically if left in this  
condition for 5 minutes. ”TAPE END“ also appears  
when a cassette whose tape is already at its end is  
loaded.  
● If the Record–Standby mode continues for 5 minutes,  
the camcorder’s power shuts off automatically. Set the  
power switch to POWER OFF, and then back to  
CAMERA to turn the camcorder on again.  
● If you’re recording on a cassette from the middle, use  
the RETAKE function (੬ pg. 15) to find the end of the  
last recording so you don’t erase any of it.  
● The LENS COVER warning blinks for about 5 seconds  
when the camcorder is turned on, whether the cover is  
open or closed.  
Tally lamp  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING Basic Features  
15  
FEATURE:  
PURPOSE:  
Zooming  
Zoom indicator  
Zoom-in  
Varies the focal length of the lens and  
produces the zoom in/out effect.  
Zoom In  
OPERATION:  
T
T
T
T
1) Pull the power zoom switch down  
toward “T”.  
W
W
W
W
Zoom Out  
2) Push the switch up toward “W”.  
● The further the power zoom switch is  
pushed, the faster the zoom speed  
becomes.  
Zoom-out  
NOTES:  
● Focusing may become unstable during  
zooming. In this case, set the zoom while  
in Record–Standby, set manual focus or  
Focus Lock (੬ pg. 20, 21), then zoom in  
or out in Record mode.  
RETAKE  
FEATURE:  
Quick Review  
PURPOSE:  
OPERATION:  
To check the end of the last recording.  
1) Press “ ” for less than 2 seconds during  
the Record–Standby mode.  
Power zoom switch  
• Tape is rewound for about 2 seconds  
and played back automatically, then  
pauses in Record–Standby mode for the  
next shot.  
NOTE:  
Distortion may occur at start of playback.  
This is normal.  
FEATURE:  
Retake  
PURPOSE:  
OPERATION:  
To re-record certain segments.  
1) Make sure the camcorder is in the  
Record–Standby mode.  
2) Press either RETAKE button to reach the  
start point for new recording.  
3) Press Recording Start/Stop to start  
recording.  
NOTE:  
Noise may appear during Retake.  
This is normal.  
FEATURE:  
PURPOSE:  
Index Code Marking  
To give you automatic access to any selected  
point on a recording. Auto Marking and  
Manual Marking are available.  
Auto Marking  
OPERATION:  
An index code is always marked to start the  
first recording on a new date after a cassette  
is inserted.  
Manual Marking (Using the optional  
RM-V700U Remote Control Unit)  
1) Press VISS once to place the index code.  
INDEX blinks in the viewfinder during  
marking.  
START/STOP  
VISS  
NOTES:  
● If VISS is pressed during  
Record–Standby mode, the mark is  
placed where START/STOP is pressed.  
● If the date changes during a recording, it  
becomes the first recording of the new  
date and an index mark is placed at that  
point.  
RM-V700U (optional)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING Advanced Features  
16  
Program AE With Special Effects  
All you have to do to access any of the variety of  
shooting effects is to turn the PROGRAM AE select  
dial until the desired indication appears in the  
viewfinder. The mode is activated about 1 second  
later.  
PROGRAM AE  
select dial  
DIAL  
SYMBOL  
VIEWFINDER  
INDICATION  
Tally lamp  
MODE  
LOCK  
AUTO LOCK Auto Mode Lock  
A
DIAL  
SYMBOL  
VIEWFINDER  
INDICATION  
Auto Mode Lock  
MODE  
Sports  
Locks the camcorder in Full Auto mode, preventing  
incorrect operation due to accidental button  
pressing during shooting.  
SPORTS  
•CINEMA, FADER, FOCUS, EXPOSURE, DISPLAY,  
TITLES and MWB (Manual White Balance)  
controls are disabled in this mode.  
Sports  
High shutter speed clearly captures fast-moving  
action.  
Auto Mode  
Release  
RELEASE  
AUTO RELEASE  
M
1/2000  
S 1/2000  
High Speed Shutter  
Auto Mode Release  
Re-enables the controls that were disabled by Auto  
Mode Lock.  
High-Speed Shutter (1/2000s.)  
Captures faster action than Sports mode.  
SELF TIMER  
FG  
FG:FOG  
Electronic Fog Filter  
15 sec. Self-Timer  
Electronic Fog Filter  
15sec. Self-Timer  
Makes the picture look misty white, as when an  
external fog filter is attached to the lens. Softens the  
image and gives it a “fancy“ look.  
Lets you delay recording start after Recording Start/  
Stop is pressed. If camcorder is secured, operator  
can enter scene before recording starts.  
1) Set PROGRAM AE dial to “ ”. “ 15S” appears  
in viewfinder.  
ND  
ND:ND EFFECT ND Effect  
2) Press Recording Start/Stop.  
ND EFFECT  
•Recording starts after 15 seconds.  
•Tally lamp begins blinking; blinking speed  
increases about 5 seconds before recording starts.  
Blinking stops when recording begins but light  
stays on.  
A black mist darkens the picture, as when an ND  
filter is used. Helps to counter the effects of glare on  
the subject.  
SEPIA  
Sepia  
NOTES:  
Sepia  
● Only one effect can be engaged at a time.  
● When the PROGRAM AE select dial is switched  
from one mode to another, the newly selected  
mode's name and its indication is displayed in the  
viewfinder for approx. 3 seconds. Then the name  
disappears, and only the indication remains.  
● The screen becomes slightly reddish when the  
fader (੬ pg. 19) is used in the Sepia mode.  
● The screen becomes slightly dark in the High  
Speed Shutter mode. Use in well-lighted  
situations.  
The scene being shot is recorded in sepia-tinted  
(reddish-brown) monochrome, giving the effect of  
an older movie. Use together with Cinema  
(੬ pg. 19) for the authentic look of a classic  
Hollywood movie.  
TWILIGHT Twilight  
Twilight  
Disengages the auto gain control and auto focus,  
locks focus to infinity and white balance to “  
”
● In the High Speed Shutter or Sports modes,  
picture color may be adversely affected if subject  
is lit by alternating discharge-type light sources  
such as flourescent or mercury-vapor lights.  
(outdoor) mode. Dusk, twilight scenery, fireworks,  
etc., look more natural and dramatic.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
White Balance Adjustment  
White balance mode indicator  
This camcorder’s Automatic Color Temperature system  
senses the color temperature of the ambient lighting for  
automatic white balance adjustment. However, precise  
color adjustment is not possible under the following  
conditions:  
No indication  
(Auto)  
•When an object is in various shades of the same color.  
•When a predominantly red or brown object is being  
shot outdoors.  
MWB  
In these cases, use the camcorder’s built-in preset filters  
for white balance adjustment.  
SELECT MODE  
Press MWB (Manual White Balance) until the  
1
required indication appears in the viewfinder.  
“
” .............. Outdoors on cloudy day  
MWB  
“
“
” ............... Outdoors on sunny day  
” ................ Light source is halogen or tungsten  
...................... lamp  
“MWB” .......... With a memorized personal White  
...................... Balance setting (see below)  
MWB sets the color temperature for the subject’s light  
source so you can shoot with natural colors that are  
unaffected by surroundings, even when there are  
multiple subjects with different color temperatures.  
ADJUST FOCUS  
Point the camcorder at a white, flat object such as a  
1
2
sheet of white paper, and adjust focus manually  
(੬ pg. 21).  
ADJUST WHITE BALANCE  
Press MWB until ”MWB“ appears, then press and  
hold MWB for more than 3 seconds.  
•”MWB” blinks in the viewfinder during  
adjustment, then stops blinking but stays lit when  
adjustment is complete.  
NOTES:  
● To switch to automatic white balance adjustment, press MWB until the indication disappears, or turn the  
PROGRAM AE dial to LOCK.  
● Re-adjust the White Balance mode when the lighting has changed, when the camcorder has been turned  
on and off again, or when the PROGRAM AE dial’s position has been changed.  
● It is helpful to connect your camcorder to a color monitor when adjusting the white balance  
(“BASIC CONNECTIONS” ੬ pg. 29).  
● When adjusted by putting colored paper in front of the subject in step 2 , this unit makes its color  
temperature standard for automatic white balance. So you can enjoy shooting with different colors. For  
example, when adjusting with red, blue or yellow colors, the image becomes the color which aproximates  
to green, orange or purple respectively.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING Advanced Features  
18  
Video Light  
When natural lighting is too dim, you can brighten the  
scene by using the built-in video light.  
SET VIDEO LIGHT  
Set the LIGHT ON/AUTO/OFF as required.  
1 ON  
: Always keeps the light on as long as the  
camcorder is turned on.  
AUTO : Automatically turns on the light when the  
camcorder senses insufficient lighting on  
the subject.  
LIGHT ON/AUTO/OFF  
OFF : Turns off the light.  
•The video light can be used with the camcorder's  
power on.  
•It is recommended to set the white balance to indoor  
mode ( ) (੬ pg. 17) when you use the video light.  
•When not using the video light, turn it off to save  
battery power.  
DANGER:  
Ⅲ The video light becomes extremely hot. Do not  
touch it either while in operation or soon after  
turning it off, otherwise serious injury may result.  
Ⅲ Do not place the camcorder into the carrying  
case immediately after using the video light, since  
it remains extremely hot.  
Ⅲ When operating, keep a distance of about  
30 cm (1 ft.) between the video light and people  
or object.  
Ⅲ Do not use near flammable or explosive  
materials.  
Ⅲ It is recommended that you consult your nearest  
JVC dealer for replacing the video light.  
NOTES:  
Ⅲ Even if the battery indicator (  
) does not blink in the  
viewfinder, if the battery pack's charge is low, the  
camcorder may turn off automatically when you turn  
on the video light, or when you start recording with the  
video light turned on.  
Ⅲ When the LIGHT ON/AUTO/OFF is set to "AUTO":  
•Depending on lighting conditions, the video light  
may keep turning on and off. In this case, manually  
switch the light on or off using the LIGHT ON/  
AUTO/OFF switch.  
Group 1  
F1  
F2  
CINEMA  
FADER  
F1  
F2  
FADER CINEMA  
SEL.  
•While the Sports or High-Speed Shutter mode  
(੬ pg. 16) is engaged, the light is likely to stay on.  
•While the Twilight mode (੬ pg. 16) is engaged, the  
light will not activate.  
Group 2  
F1  
F2  
FOCUS  
EXP.  
SEL.  
Viewfinder  
Group 3  
INTELLIGENT FUNCTION CONTROL  
F1  
F2  
TITLE  
DISP.  
This feature makes it easier for you to make selections  
during the following modes: Fader, Cinema, Manual  
Focus Adjust, Exposure Control, Display, and Instant  
Title.  
SEL.  
F1 button  
F2 button  
F1  
SEL  
F2  
PREPARATION  
Set the PROGRAM AE dial to any position except  
1
2
3
LOCK.  
SELECT MODE  
Function SEL. button  
Press Function SEL. repeatedly until the required  
function’s indication appears in the viewfinder.  
PROGRAM AE select dial  
ENTER SELECTION  
Press either F1 or F2 (the one to the immediate left  
of the desired function name).  
NOTE:  
If you set the PROGRAM AE dial to LOCK, F1 and F2  
disappear from the viewfinder, indicating that IFC  
(Intelligent Function Control) is unavailable.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
Fader  
F1 button F2 button  
This feature allows smooth fade-in and fade-out to black  
blank screen. Fade-in works at recording start, and  
fade-out works at recording end or when you enter  
Record–Standby mode.  
F1  
SEL  
F2  
SELECT MODE  
Press Function SEL. repeatedly until “FADER”  
Function SEL. button  
1
2
3
appears to the right of F1.  
PROGRAM AE select dial  
ENGAGE FADE–STANDBY MODE  
Press F1 to engage the Fade–Standby mode.  
“FADER”appears in the viewfinder.  
START RECORDING  
Press Recording Start/Stop to start recording and  
activate fade-in.  
OR . . .  
END RECORDING  
Press Recording Start/Stop to end recording and  
engage fade-out.  
FADE IN  
NOTES:  
● Pressing and holding the Recording Start/Stop button  
allows you to record a black blank screen.  
● The screen becomes slightly reddish when the Fader is  
used with Sepia (੬ pg. 16).  
● With the Electronic fog filter mode (੬ pg. 16)  
engaged, the image fades in/out to a white screen.  
FADE OUT  
Cinema  
This feature allows you to record black bars at the top  
and bottom of the screen to produce a cinema-like  
“wide-screen” effect.  
Cinema mode  
SELECT MODE  
Press Function SEL. repeatedly until “CINEMA”  
1
2
3
appears to the right of F2.  
ENGAGE CINEMA MODE  
Press F2.  
RESTORE NORMAL SCREEN  
Press F2 again while “CINEMA” appears next to F2  
in the viewfinder.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING Advanced Features  
Focusing  
Auto Focus  
The camcorder’s Full Range AF system offers continuous  
shooting ability from close-up to infinity. However,  
correct focus may not be obtainable in the situations  
listed below (in these cases use manual focusing):  
20  
Focus  
detection zone  
•When two subjects overlap in the same scene.  
•When illumination is low.*  
•When the subject has no contrast (difference in  
brightness and darkness), such as a flat, one-color wall,  
or a clear, blue sky.*  
F1  
F2  
•When a dark object is barely visible in the viewfinder.*  
•When the scene contains minute patterns or identical  
patterns that are regularly repeated.  
* The low-contrast warning “  
viewfinder.  
” appears in the  
Focus Lock  
This feature locks the focus in place, which is especially  
helpful in the following situations:  
•When things pass between your subject and the  
camcorder. Engage the focus lock function to lock your  
subject in before recording.  
Function SEL.  
•When you want your subject to be focused, and to  
appear in a corner of the screen. First, center on the  
subject and focus using auto focus mode. Then engage  
the focus lock function and move the camcorder until  
the subject is where you want it.  
SELECT MODE  
Press Function SEL. repeatedly until “FOCUS”  
1
2
3
appears to the right of F1.  
LOCK FOCUS  
Press F1. The focus lock indication “  
in the viewfinder.  
” appears  
RELEASE FOCUS LOCK  
Press F1. Focus lock is immediately released. The  
focus lock indication disappears.  
NOTES:  
● If the lens is smeared or blurred, accurate focusing is  
not possible. Keep the lens clean, wiping with a piece  
of soft cloth if it gets dirty. When condensation occurs,  
wipe with a soft cloth or wait for it to dry naturally.  
● When shooting a subject close to the lens, zoom-out  
first (੬ pg. 15). If zoomed-in in the auto focus mode,  
the camcorder could automatically zoom out  
depending on the distance between the camcorder and  
the subject.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
Manual Focus  
F1 button  
F2 button  
NOTE:  
You should already have made the necessary viewfinder  
adjustments (੬ pg. 11). If you haven’t, do so before  
continuing.  
F1  
SEL  
F2  
SELECT MODE  
Function SEL.  
button  
Press Function SEL. repeatedly until “FOCUS”  
F1  
F2  
EXP.  
FOCUS  
1
appears to the right of F1.  
ADJUST FOCUS  
Power zoom switch  
A
TO FARTHER SUBJECT  
2
Viewfinder  
While holding down F1, slide the power zoom  
switch to T. The Manual Focus indications “  
appear and “ ” blinks.  
2
”
Go to step 3.  
B
TO NEARER SUBJECT  
While holding down F1, slide the power zoom  
switch to W. The Manual Focus indications  
“
” appear and “ ” blinks.  
Go to step 3.  
LOCK FOCUS  
Release the power zoom switch. The focus  
3
4
indication is replaced by the focus lock indication  
“
” and the adjusted focus is locked in.  
RELEASE MANUAL FOCUS MODE  
F1  
F1  
+
+
Press F1. The Manual Focus mode is immediately  
released and the focus lock indication disappears.  
NOTES:  
● Be sure to focus the lens in the maximum telephoto  
position when you use the Manual Focus mode. If you  
focus in on a certain subject in the wide-angle position,  
sharply focused images cannot be obtained when  
zoomed up because the depth-of-field is reduced at  
longer focal lengths.  
● Two manual focusing speeds are available. For  
slow-speed, push the switch slightly and hold that  
position. For fast-speed, push the switch fully.  
● When the focus level cannot be adjusted any farther or  
closer, “ ” or “ ” will blink.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING Advanced Features  
22  
Exposure Control  
F1 button  
F2 button  
This feature automatically adjusts the iris for the best  
available picture quality, but you can override and make  
the adjustment manually.  
F1  
SEL  
F2  
SELECT MODE  
Press Function SEL. repeatedly until “EXP.” appears  
1
2
to the right of F2.  
Function SEL.  
button  
F1  
F2  
EXP.  
FOCUS  
BRIGHTEN IMAGE  
While holding down F2, slide the power zoom  
switch to T. The Exposure indicator bar appears in  
the viewfinder.  
Power zoom switch  
Viewfinder  
OR . . .  
DARKEN IMAGE  
While holding down F2, slide the power zoom  
switch to W. The Exposure indicator bar appears in  
the viewfinder.  
When you want to return to the factory setting . . .  
RESTORE INITIAL SETTING  
Press F2. The standard setting is immediately  
restored and the Exposure indicator bar disappears.  
3
To brighten the image  
+
F2  
+
+
+
-
-
-
+
F2  
To darken the image  
Exposure indicator bar  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
Date/Time Character Insert  
F1 button  
F2 button  
This feature allows you to display date, time and characters  
in your viewfinder and on a connected color monitor,  
record them manually or automatically, and even make  
your own titles.  
F1  
SEL  
F2  
NOTE:  
You should already have performed the Date/Time Setting  
procedure (੬ pg. 10). If you haven’t, do so before continuing.  
Function SEL. button  
DISPLAY  
SELECT DISPLAY  
Press Function SEL. repeatedly until “DISP.” appears  
1
2
to the right of F2.  
CHOOSE DISPLAY MODE  
Press F2 while in Record–Standby to cycle through  
the modes as shown in the illustration at left.  
F1  
F2  
DISP.  
TITLE  
NOTES:  
● The selected display can be recorded.  
● If you don’t want to record the display, select Date-off mode  
before shooting.  
● If you want to delete the display during shooting, press F2.  
● If you want to call back a deleted display, engage the Record–  
Standby mode and then select the desired display mode using F2.  
Date display  
Auto Date Record mode  
Date/Time display  
Character Generator  
AUTO DATE RECORD  
Your camcorder automatically records the month, day  
and year for about 5 seconds after recording is initiated  
in the following situations:  
Date-off mode  
On-screen display  
Date display  
Auto Date Record mode  
•After changing the date.  
•After loading a cassette.  
•After Auto Date Record mode is selected by pressing  
F2. In this mode, the month, day and year are replaced  
after 5 seconds with “AUTO DATE”.  
DEC 25.96  
AUTO DATE  
DEC 25.96  
Auto date  
record mode  
Auto date  
record executed  
NOTES:  
Date/Time display  
Character Generator  
● Setting PROGRAM AE to LOCK always engages this mode, and  
disables all other modes.  
● In the Auto Date Record mode, if the date changes while you’re  
shooting, the date indication is recorded for about 5 seconds  
from that point. It is not recorded during any other recordings  
made on that day.  
DEC 25.96 PM 10:50  
SET CHAR  
IN PARIS, FRANCE  
No Characters  
stored  
Example of  
stored characters  
ON-SCREEN DISPLAY  
CONNECT CAMCORDER TO  
MONITOR  
Connect the camcorder to a monitor as instructed in  
1
2
“BASIC CONNECTIONS” (੬ pg. 29).  
NOTES:  
DISPLAY VIEWFINDER  
INDICATIONS  
● In the On-Screen Display mode, the date is  
displayed and recorded.  
Press F2 until the indications appear on the  
● The on-screen display is not available during  
recording.  
connected monitor.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING Advanced Features  
Character Generator  
24  
–/+  
SET  
SELECT MODE  
Press Function SEL. repeatedly until “DISP.” appears  
1
2
to the right of F2.  
SET CHARACTER OR TITLE  
Press F2 until “SET CHAR” or a previously stored  
title appears in the viewfinder.  
ACCESS CHARACTER MODE  
SCREEN  
Press SET. A character grid appears in the view  
3
4
finder.  
ENTER DESIRED CHARACTERS  
Press + or – to move the cursor on the character grid  
to the desired character, then press SET to enter. The  
selected characters appears at the bottom of the  
screen. When you’re done, press SET as many times  
as necessary to exit the screen. The title you made  
appears at the bottom of the screen.  
CHARACTER  
SET MODE screen  
NOTES:  
CHARACTER SET MODE  
A
K
U
È
.
B
L
V
Ì
C
M
W
Ò
'
D
N
X
Ù
-
E
O
Y
F
P
Z
G
Q
Ä
H
R
Ö
Å
I
● You can store up to 18 characters.  
● You can only make and store one title at a time. To  
replace it, repeat the procedure.  
J
T
À
:
S
Ü
&
Ñ Æ Ø  
,
/
5
!
6
?
7
¿ 
ࡖ
 
9
0
1
2
3
4
8
● To create a space between two characters in a title you  
make, choose “ ” on the CHARACTER SET MODE  
screen.  
SET CHAR  
CHARACTER SET MODE  
A
K
U
È
.
B
L
V
Ì
C
M
W
Ò
'
D
N
X
Ù
-
E
O
Y
F
P
Z
G
Q
Ä
H
R
Ö
Å
I
J
T
À
:
S
Ü
&
Ñ Æ Ø  
,
/
5
!
6
?
7
¿ 
ࡖ
 
9
0
1
2
3
4
8
IN PARIS, FRANCE  
I N PAR I S, FR  
CHARACTER  
SET MODE screen  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
Instant Titles  
Example of Character Generator & Title  
Viewfinder  
The camcorder has eight preset titles in memory. You can  
superimpose one of them above a previously stored title  
as shown in the illustration to the left.  
The preset titles appear in this order: HAPPY BIRTHDAY,  
OUR VACATION, MERRY CHRISTMAS, A SPECIAL DAY,  
HAPPY HOLIDAYS, OUR NEW BABY, WEDDING DAY,  
CONGRATULATIONS.  
OUR VACATION  
IN PARIS, FRANCE  
Character Generator:  
Title indication  
SELECT MODE  
IN PARIS, FRANCE  
Press Function SEL. repeatedly until “TITLE” appears  
Title: OUR VACATION  
1
2
to the right of F1.  
SELECT PRESET TITLE  
Engage the Record–Standby mode, then press F1 to  
cycle through the preset titles until the desired title is  
displayed.  
NOTES:  
● To delete the Instant Title during recording, press F1.  
● To recall a title, engage the Record–Standby mode and  
then press F1 to select the desired title.  
● To display a title you made in the position usually  
occupied by an Instant Title, cycle through in step 2  
above until your title appears  
(after “CONGRATULATIONS”). You can superimpose  
two personal titles on the scene being shot.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING Advanced Features  
26  
Self-Timer  
Tally lamp PROGRAM AE  
You can set the delay between pressing Recording Start/  
Stop and the actual start of recording. If you secure the  
camcorder, you (or whomever is operating the  
camcorder) can enter the scene before recording starts.  
NOTE:  
You need the RM-V700U remote control unit to perform  
this procedure.  
ENGAGE RECORD–STANDBY  
MODE  
Make sure the lens cover is open, set the power  
1
2
switch to CAMERA.  
SET TIME DELAY  
On the remote control, press INT. TIME to set the  
delay time. There are four choices, and they appear  
in the viewfinder in the following order (each time  
INT. TIME is pressed): 15S (15 seconds), 30S  
(30 seconds), 1MIN (1 minute) and 5MIN  
(5 minutes). Pressing again releases the Self-timer.  
START/STOP  
INT. TIME  
REC TIME  
START DELAYED RECORDING  
Press Recording Start/Stop. The tally lamp begins  
blinking, and the blinking speed increases about  
5 seconds before recording starts. When recording  
begins, the lamp stops blinking but stays lit.  
RM-V700U  
(optional)  
3
4
RELEASE SELF-TIMER MODE  
To release when the tally lamp is not blinking, press  
INT. TIME continuously until “ ” disappears. To  
release when the tally lamp is blinking, press  
Recording Start/Stop to stop the blinking, then press  
INT. TIME continuously until “ ” disappears.  
NOTE:  
If the PROGRAM AE dial is set to “ ”, 15S is  
automatically selected.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
Animation  
Time-Lapse  
Give stationary scenes or objects an illusion of  
movement. This function allows you to shoot a  
series of pictures, each slightly different, of the same  
object for a brief period of time.  
You can record sequentially at preset time spans.  
Leaving the camcorder aimed at a specific subject,  
you can record subtle changes over an extended  
period of time.  
NOTE:  
NOTE:  
You need the RM-V700U remote control unit to  
perform the following procedure.  
You need the RM-V700U remote control unit to  
perform the following procedure.  
ENGAGE RECORD–STANDBY  
ENGAGE RECORD–STANDBY  
MODE  
MODE  
Make sure the lens cover is open, then set the  
power switch to CAMERA.  
Make sure the lens cover is open, then set the  
power switch to CAMERA.  
1
2
3
1
2
3
SET RECORDING SPEED  
SET RECORDING SPEED  
Set SP/EP to SP (੬ pg. 11).  
Set SP/EP to SP (੬ pg. 11).  
SET RECORDING TIME  
SET RECORDING TIME  
Press REC TIME on the remote control. There  
are three choices available, and they appear in  
the following order (each time REC TIME is  
pressed): 1/4S, 1/2S and 1S. Press again to  
reset.  
Press REC TIME on the remote control. Three  
choices are available, and they appear in the  
following order (each time REC TIME is  
pressed): 1/4S (one-fourth of a second), 1/2S  
(one-half of a second) and 1S (one full second).  
Press again to release the animation mode.  
SET INTERVAL BETWEEN  
START RECORDING  
RECORDINGS  
Press Recording Start/Stop after focusing on the  
subject. The recording stops automatically after  
the selected period of time.  
Press INT. TIME on the remote control. There  
are four choices available, and they appear in  
the following order (each time INT. TIME is  
pressed): 15S, 30S, 1MIN, and 5MIN. Press  
again to reset.  
4
4
ASSEMBLE SERIES OF  
PICTURES  
START TIME-LAPSE  
Repeat steps 3 and 4 for the desired number of  
5
6
7
pictures.  
RECORDING  
Press Recording Start/Stop. Recording and  
intervals alternate automatically.  
CHECK YOUR WORK  
5
6
Play back the series of pictures to see if the  
results were satisfactory.  
RELEASE TIME-LAPSE MODE  
To release when the tally lamp is not blinking,  
press INT. TIME and REC TIME repeatedly  
until “ ” and “ ” disappear. To release  
when the tally lamp is blinking, press  
Recording Start/Stop to stop the blinking, then  
press INT. TIME and REC TIME repeatedly  
until “ ” and “ ” disappear.  
RELEASE ANIMATION MODE  
Press REC TIME until “ ” disappears from the  
viewfinder.  
NOTES:  
● For best results, make sure the camcorder is  
secured when shooting.  
NOTES:  
● If the PROGRAM AE dial is set to Self-Timer  
mode, Animation is cancelled and Self-Timer  
mode is engaged with 15S selected.  
● Fade-in/out cannot be performed during  
Animation shooting.  
● Fade-in/out cannot be performed during  
Time-Lapse shooting.  
● For best results, keep the camcorder secured  
while shooting.  
● If, during steps 3 and 4, the PROGRAM AE dial is  
set to the Self-Timer mode, the Self-Timer mode is  
engaged with 15S selected.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK Using The Cassette Adapter  
28  
Cassette Adapter (VHS PlayPak)  
Use this to play back a VHS-C video cassette recorded  
with this camcorder. It is fully compatible with any VHS  
video cassette recorder. The C-P7U adapter is battery  
powered and automatically performs tape loading and  
unloading.  
+
INSERT BATTERY  
Slide the battery cover up to remove it, and install  
one “AA(R6)” size battery as shown in the  
illustration at left. Then reattach the cover.  
1
2
3
VCR  
INSERT CASSETTE IN ADAPTER  
Slide the latch to open the adapter compartment  
door, then insert the cassette and close the  
compartment door.  
Compartment door  
PLAY BACK ON CONNECTED VCR  
Load the cassette adapter into the VCR and play the  
tape back as you would any other.  
REMOVE CASSETTE FROM  
ADAPTER  
Slide the latch and the compartment door opens  
automatically. Then insert your finger in the hole on  
the underside of the adapter as shown in the  
4
Sliding latch  
Reels  
illustration at left, push up and remove the cassette.  
Compact video cassette  
NOTES:  
● During tape loading and unloading, do not touch the  
reels for safety and tape protection.  
● During special-effect playback (slow motion, still  
frame, etc.), the picture may vibrate or noise bars may  
appear on the screen.  
● To record on a VCR using a compact cassette and the  
adapter, cover the adapter’s recording safety hole with  
adhesive tape.  
Recording safety hole  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK Basic Connections  
29  
There are three basic types of connections. When making  
the connections, refer also to your VCR and TV  
instruction manuals.  
Connection To A VCR [A]  
(Editing, Dubbing and Playback)  
NOTE:  
Use the optional Audio and Video cables.  
To AUDIO  
CONNECT CAMCORDER TO VCR  
and VIDEO  
Audio and Video  
cables (optional)  
As shown in the illustration at left, connect the  
connectors  
1
optional Audio and Video cables between the  
AUDIO and VIDEO connectors on the camcorder  
and those on the VCR.  
A
B
To AUDIO and  
VIDEO IN  
connectors  
SUPPLY POWER  
Turn on the camcorder, the VCR and the TV.  
2
3
SELECT MODE  
VCR  
Set the VCR to its AUX input mode, and set the TV  
to its VIDEO mode or channel 3.  
Aerial  
Connection To A TV With A/V Input  
Connectors [B] (Playback ONLY)  
NOTE:  
Use the optional Audio and Video cables.  
CONNECT CAMCORDER TO TV  
To AUDIO, VIDEO and  
DC OUT connectors  
As shown in the illustration at left, connect the  
1
2
optional Audio and Video cables between the  
AUDIO and VIDEO connectors on the camcorder  
and those on the TV.  
RF unit RF-V5U  
(optional)  
SELECT MODE  
Set the TV to its VIDEO or AV mode (as specified in  
its instructions).  
NOTES:  
Connection To A TV With NO A/V Input  
Connectors (Playback ONLY)  
● It is recommended to use the AC Power  
Adapter/Charger as the power supply instead  
of the battery pack.  
NOTE:  
● To monitor the picture and sound from the  
camcorder without inserting a tape, set the  
camcorder’s power switch to CAMERA, then  
set your TV to the appropriate input mode.  
● If you have a TV or speakers that are not  
specially shielded, do not place the speakers  
adjacent to the TV as interference will occur  
in the camcorder playback picture.  
Use the optional RF-V5U RF unit.  
* Refer to the RF-V5U instruction manual for connection  
procedure.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK Basic Playback  
30  
NOTE:  
PLAY/PAUSE  
STOP  
Make sure you connect your camcorder as directed in  
“BASIC CONNECTIONS” (੬ pg. 29 ).  
LOAD A CASSETTE  
Slide EJECT to open the cassette holder, then insert  
the cassette with the label facing out. Press PUSH to  
ensure the holder is closed and locked.  
FF  
REW  
1
SELECT MODE  
Set the power switch to PLAY. The Power On  
indicator lights.  
2
3
4
PLAYBACK  
Press PLAY/PAUSE. The playback picture appears in  
the viewfinder and the connected TV.  
STOP PLAYBACK  
Press STOP.  
Rewind or Fast-forward the tape  
Press REW to rewind, or FF to fast-forward the tape  
POWER  
during Stop mode.  
NOTE:  
The camcorder shuts off automatically after about 5  
minutes in STOP mode. To turn on again, set the power  
switch to POWER OFF, then to PLAY.  
M 0:00:00  
Tape counter  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK Features  
31  
To eliminate noise bars that appear  
on the screen.  
TRACKING  
COUNTER R/M  
PLAY/PAUSE  
FEATURE:  
PURPOSE:  
Manual Tracking  
OPERATION: 1) Press either TRACKING button as  
many times as necessary for best  
picture.  
NOTES:  
● To reset TRACKING to the original  
preset, press both TRACKING  
buttons simultaneously.  
REW  
● Manual Tracking may not work with  
tapes recorded on other VCRs or  
camcorders.  
FF  
STOP  
FEATURE:  
PURPOSE:  
Still Playback  
To pause during playback.  
OPERATION: 1) Press PLAY/PAUSE during  
playback.  
2) To resume normal playback, press  
PLAY/PAUSE again.  
NOTE:  
Noise bars appear and pictures may  
become monochrome during Still  
Playback. This is normal.  
FEATURE:  
PURPOSE:  
Shuttle Search  
To allow high-speed search in either  
direction.  
OPERATION: Forward Search  
1) Press FF during playback. (Speed is  
3 times normal in SP, and 7 times  
normal in EP mode.)  
Reverse Search  
1) Press REW during playback.  
(Speed is as noted above.)  
Noise bars appear and pictures may  
become monochrome in Shuttle  
Search. This is normal.  
NOTE:  
FEATURE:  
PURPOSE:  
Counter Memory Function  
To make it easier to locate a specific  
tape segment.  
REW  
FF  
OPERATION: 1) Press COUNTER R/M and hold for  
more than 2 seconds. The counter  
resets to “0:00:00”.  
PLAY  
2) Press COUNTER R/M. “M”  
appears.  
PAUSE  
3) After recording or playback, press  
STOP, then REW. The tape  
automatically stops at or close to  
0:00:00.  
RM-V700U  
(optional)  
4) Press PLAY/PAUSE to start  
playback.  
● The counter memory functions in  
the FF and REW modes.  
NOTES:  
● To disable Counter Memory  
Function, press COUNTER R/M so  
the “M” disappears.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EDITING  
32  
Tape Dubbing  
Power switch  
CONNECT EQUIPMENT  
Following the illustration at left, connect the  
camcorder and the VCR. If you have a Remote  
PAUSE terminal, use the editing cable to connect it  
to the camcorder and the VCR. (See “NOTES” below  
for details.)  
1
2
EDIT  
PLAY/PAUSE  
PREPARE FOR DUBBING  
Set the camcorder’s power switch to PLAY, turn on  
the VCR’s power, and insert the appropriate  
cassettes in the camcorder and the VCR.  
SELECT VCR MODE  
To EDIT  
Engage the VCR’s AUX and Record-Pause modes.  
To AUDIO out  
3
4
To VIDEO out  
FIND EDIT-IN POINT  
Engage the camcorder’s Play mode to find a spot  
just before the edit-in point. Once it’s reached, press  
PAUSE on the camcorder.  
Editing cable  
(optional 3.5 ø  
mini-plug cable)  
Audio and Video  
cable (optional)  
START EDITING  
Press PLAY on the camcorder and engage the VCR’s  
Record mode.  
5
6
7
To Remote  
PAUSE  
To AUDIO IN  
To VIDEO IN  
STOP EDITING TEMPORARILY  
Engage the VCR’s Record-Pause mode and press  
PAUSE on the camcorder.  
VCR (Recording deck)  
EDIT MORE SEGMENTS  
Repeat steps 4 through 6 for additional editing, then  
stop the VCR and camcorder when finished.  
NOTES:  
● When using a Remote PAUSE terminal, pressing EDIT  
on the camcorder in step 5 automatically engages the  
VCR’s Record mode.  
● When using a Remote PAUSE terminal, you can access  
a function called Master Edit Control System. Before  
beginning, reset the camcorder’s counter to  
“M0:00:00” at an edit-out point. When the tape  
reaches this point (remember there’s a small margin of  
error) during editing, the camcorder and VCR pause  
automatically. However, some VCRs are not compat-  
ible with the Master Edit Control System.  
Random Assemble Editing [R.A.Edit]  
Create edited videos easily using your camcorder as the  
source player. You can select up to 8 “cuts” for automatic  
editing, in any order you like. R.A.Edit is more easily  
performed when the optional RM-V700U MBR  
(Multi-Brand Remote) is set to operate with your brand of  
VCR (see chart at left), but can also be performed by  
operating the VCR manually.  
CONTINUED ON NEXT PAGE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
33  
SET REMOTE/VCR CODE  
SET REMOTE TO OPERATE VCR  
Turn off the power to the VCR and point the remote  
toward the VCR’s infrared sensor. Then, referring to  
the chart at left, press and hold MBR SET, and press  
button (A) and then (B).  
MBR SET  
VCR. CTL.  
1
2
1
4
7
2
5
8
3
6
9
0
•The code is automatically set once you release the  
MBR SET button, and the VCR’s power comes on.  
RM-V700U (optional)  
VCR CODE LIST  
OPERATE THE VCR  
Make sure the VCR’s power is on. Then, while  
holding VCR CTL, press the button on the remote for  
the desired function. The functions the remote can  
control are PLAY, STOP, PAUSE, FF, REW and VCR  
REC STBY (you don’t need to press VCR CTL for this  
one).  
VCR BRAND BUTTONS  
VCR BRAND BUTTONS  
NAME  
PHILIPS  
NAME  
GE  
(A) (B)  
(A) (B)  
1
9
9
9
6
6
9
9
9
9
1
7
7
6
6
3
3
1
9
1
9
9
9
1ꢀ  
2ꢀ  
`ꢀ  
4
6ꢀ  
3
1ꢀ  
6ꢀ  
3
5ꢀ  
1ꢀ  
1ꢀ  
6
7ꢀ  
8
7ꢀ  
8
9ꢀ  
5ꢀ  
1ꢀ  
4ꢀ  
1ꢀ  
6
1
3
2ꢀ  
3
PANASONIC  
RCA  
1
1
1
9
1
3ꢀ  
7ꢀ  
1ꢀ  
4ꢀ  
8ꢀ  
HITACHI  
You’re now ready to try Random Assemble Editing.  
JVC  
A
B
C
ꢀ
9
9
6
6
9
2ꢀ  
4ꢀ  
6ꢀ  
3ꢀ  
`
IMPORTANT  
Although the MBR is compatible with JVC VCRs and  
those of many other makers, it may not work with yours  
or may offer limited functions.  
MAGNAVOX  
SANYO  
SHARP  
SONY  
3
3
6ꢀ  
5
MITSUBISHI  
NEC  
NOTES:  
1
1
5ꢀ  
`
● If the VCR’s power doesn’t come on in step 1, try  
another code from the chart.  
6
6
3
3
5ꢀ  
`ꢀ  
9ꢀ  
1ꢀ  
● Some brands of VCR don’t come on automatically. In  
this case, turn the power on manually and try step 2.  
● If the RM-V700U is not able to control the VCR, use  
the controls on the VCR.  
PHILIPS  
ꢀ
TOSHIBA  
ZENITH  
6
6
9ꢀ  
1
1
6
MAKE CONNECTIONS  
CONNECT TO . . .  
A
JVC VCR EQUIPPED WITH REMOTE  
1
PAUSE TERMINAL  
Connect the editing cable to the Remote PAUSE  
terminal.  
B
JVC VCR NOT EQUIPPED WITH REMOTE  
PAUSE TERMINAL  
2
Connect the editing cable to the R.A.EDIT  
connector.  
C
NON-JVC VCR WITH NEITHER  
2
Connect the editing cable to the RM-V700U's  
Pause-In jack.  
All other connections are as shown in the illustration  
on page 34.  
CONTINUED ON NEXT PAGE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EDITING (cont.)  
34  
REW/FF CANCEL  
PREPARE CAMCORDER  
Insert a recorded tape and set the power switch to  
PLAY.  
IN/OUT  
2
3
R.A. EDIT  
PREPARE VCR  
PLAY/PAUSE  
Turn the power on, insert a recordable tape and  
engage the AUX mode (refer to VCR’s instructions).  
STOP  
SELECT SCENES  
ACCESS R.A. EDIT COUNTER  
DISPLAY  
Press PLAY/PAUSE, then press R.A. EDIT and the  
counter display appears in the viewfinder and the  
screen of the connected TV.  
1
2
3
To EDIT  
To AUDIO and  
VIDEO out  
connector  
REGISTER BEGINNING OF SCENE  
Press REW or FF to locate the beginning of a scene  
you want, then press IN/OUT to register that point.  
The data appears under IN on the display.  
Editing cable  
(optional 3.5 ø  
Audio and Video  
cable (optional)  
mini-plug cable)  
REGISTER END OF SCENE  
A
B
Press REW or FF to locate the end of the scene and  
press IN/OUT to register it. The data appears under  
OUT on the display. The total time of the registered  
scene(s) is displayed at the bottom of the screen.  
C
To Remote  
PAUSE  
To AUDIO and  
VIDEO IN  
REGISTER ADDITIONAL SCENES  
connectors  
To Pause-In  
Repeat steps 2 and 3 for each additional scene  
4
5
(as many as 8).  
VCR (Recording deck)  
MAKE CORRECTIONS  
Press CANCEL during steps 2 and 3 to erase the  
most recently registered point.  
ON/OFF  
VCR REC STBY  
NOTES:  
CANCEL  
IN/OUT  
RM-V700U (optional)  
● The RM-V700U can be used to operate other camcorder  
functions as well. Point the RM-V700U at the camcorder’s  
remote sensor and press any of the following buttons  
(function appears in parentheses):  
— ON/OFF (camcorder R.A. EDIT)  
— IN/OUT (camcorder IN/OUT)  
IN  
ᮣ 1 0:00:25  
ᮣ 2  
OUT  
IN  
ᮣ 1 0:00:25  
ᮣ 2 0:03:18  
ᮣ 3 0:02:33  
ᮣ 4 0:04:11  
ᮣ 5  
OUT  
— CANCEL (camcorder CANCEL)  
0:01:05  
0:03:31  
0:02:53  
● There must be at least one second between an in-point and  
its corresponding out-point.  
ᮣ 3  
ᮣ 4  
ᮣ 5  
● The camcorder prerolls during R.A. Edit, so there must be at  
least 15 seconds of recording material prior to any in-point.  
● Blank portions of tape cannot be registered as in-points or  
out-points.  
ᮣ 6  
ᮣ 6  
ᮣ 7  
ᮣ 7  
ᮣ 8  
COUNTER  
TOTAL  
ᮣ 8  
COUNTER  
TOTAL  
0:00:25  
0:00:00  
0:04:11  
0:01:13  
● If it takes more than 5 minutes to search for an in-point, the  
VCR’s Record-Pause mode is cancelled and editing doesn’t  
take place.  
● Pressing R.A.EDIT clears all in- and out-points from  
memory.  
● Leave a small margin for error around each in-point to  
ensure the scene is recorded in its entirety.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35  
AUTOMATIC EDITING TO VCR  
ORIGINAL TAPE (camcorder)  
1
IN  
3
2
IN  
ENGAGE VCR’S RECORD–PAUSE  
MODE  
OUT  
IN OUT  
OUT  
Point the remote control toward the VCR’s infrared  
sensor and press VCR REC STBY, or manually  
engage the VCR’s Record-Pause mode.  
1
2
3
BEGIN AUTOMATIC EDITING  
Press EDIT on the camcorder, and the previously  
selected scenes are copied to the VCR in the  
specified order.  
EDITED TAPE (VCR)  
EDIT STOP  
END AUTOMATIC EDITING  
When all selected scenes have been copied, the  
camcorder and VCR enter the still or pause mode.  
Press STOP on both units.  
NOTES:  
● If you performed step 1C on page 33, keep the remote  
control pointed at the VCR during editing.  
● The on-screen display only appears while the  
camcorder searches for each scene.  
● To dub a copy of the camcorder’s (source) tape,  
perform R.A.EDIT by specifying only one in-point  
(and no out-point). The contents of the tape from the  
specified in-point to the end of the tape are  
automatically copied.  
● There may be noise at in- or out-points on the edited  
tape with certain VCRs.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EDITING (cont.)  
36  
Insert Editing  
COUNTER R/M  
You can record a new scene into a previously recorded  
tape, replacing a section of the original recording with  
minimal picture distortion at the in- and out-points. The  
original audio remains unchanged.  
NOTE:  
You need the RM-V700U remote control unit to perform  
this procedure.  
SELECT MODE  
Set the power switch to PLAY.  
1
FIND EDIT-OUT POINT  
Locate the point and press PAUSE on the camcorder  
2
3
or the remote control.  
RESET COUNTER  
Press and hold COUNTER R/M for more than 2  
seconds to reset the tape counter, then press for less  
than 1 second and make sure “M” appears in the  
viewfinder.  
POWER  
M-0:12:34  
FIND EDIT-IN POINT  
Tape Counter  
Press REW to go a little beyond the beginning of the  
scene you want to replace, press PLAY to view the  
recorded tape, and press PAUSE at exactly at the  
point where the new scene should start.  
Insert editing  
indicator  
4
Viewfinder  
ENGAGE INSERT EDITING MODE  
Press and hold INSERT, and press PAUSE. The Insert  
mode is engaged, and the scene the camcorder is  
aimed at appears on the screen.  
5
6
BEGIN INSERT EDITING  
Press Recording Start/Stop. When the counter  
reaches “0:00:00”, editing stops automatically and  
the camcorder enters the playback mode.  
NOTES:  
● Insert Editing may not work correctly if a blank  
segment exists in the recorded tape, or if the recording  
speed was changed.  
● The tape may stop slightly before or after the  
designated end point, and noise bars may appear.  
Neither indicates a defect in the unit.  
REW  
● To edit onto a tape with the recording safety tab  
removed, cover the hole with adhesive tape.  
● Only video signal is recorded in the Insert Editing  
mode. When the sound is to be recorded, press  
A. DUB and PAUSE simultaneously after Step 5. When  
INSERT and PAUSE are pressed simultaneously again,  
the unit re-enters the Video-signal-only  
Recording mode.  
A. DUB  
PAUSE  
INSERT  
PLAY  
● If the camcorder’s mike is too close to the TV, or if the  
TV’s volume is too high, whistling or howling may  
occur.  
RM-V700U  
(optional)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
37  
Audio Dubbing  
Audio dubbing indicator  
You can record a new soundtrack on a prerecorded tape  
(normal audio only).  
Viewfinder  
** Perform steps 1, 2 and 3 of the Insert Editing procedure  
(੬ pg. 36) before continuing.  
FIND EDIT-IN POINT  
Press REW to go a little beyond the beginning of the  
1
scene onto which you want to dub new audio, press  
PLAY to view the recorded tape, then press PAUSE  
at exactly the point where dubbing should start.  
Mic  
ENGAGE AUDIO DUB STANDBY  
MODE  
Press and hold A. DUB, and press PAUSE.  
2
3
BEGIN AUDIO DUBBING  
Press PLAY. When the counter reaches “0:00:00”,  
Audio Dubbing stops automatically and the  
camcorder enters the playback mode.  
NOTES:  
● Audio Dubbing may not work correctly if the tape  
contains blank segments, or if the recording speed was  
changed during the original recording.  
● If the camcorder’s mike is too close to the TV, or if the  
TV’s volume is too high, whistling or howling may  
occur.  
REW  
A. DUB  
PAUSE  
PLAY  
RM-V700U  
(optional)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USER MAINTENANCE  
38  
After Use  
LENS COVER  
open/close switch  
Set the power switch to POWER OFF to turn off the  
camcorder.  
1
2
3
4
5
Slide EJECT to open the cassette holder, then remove  
the cassette.  
Close and lock the cassette holder by pressing  
PUSH.  
Press BATT. RELEASE to remove the battery pack.  
Slide the LENS COVER open/close switch to close  
the lens cover.  
Set to “POWER OFF”.  
BATT. RELEASE  
Cleaning The Camcorder  
CLEAN EXTERIOR  
Wipe gently with a soft cloth.  
1
EJECT  
CLEAN LENS  
Blow it with a blower brush, then wipe gently with  
2
3
4
5
lens cleaning paper.  
REMOVE EYEPIECE  
PUSH  
Turn the eyepiece counterclockwise and pull it out.  
Remove.  
CLEAN VIEWFINDER  
Remove dust using a blower brush.  
RE-ATTACH EYEPIECE  
Align the marks, re-attach the eyepiece and turn it  
clockwise.  
NOTES:  
● Avoid using strong cleaning agents such as benzine or  
alcohol.  
● Cleaning should be done only after the battery pack  
has been removed or other power units have been  
disconnected.  
Marks  
● Mold may form if the lens is left dirty.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
39  
SYMPTOM  
POSSIBLE CAUSE(S)  
POWER  
No power is supplied.  
● The battery pack has not been attached correctly  
(੬ pg. 8).  
● The battery pack is not charged (੬ pg. 8).  
● The power supply has not been correctly connected  
(੬ pg. 9).  
RECORDING  
Recording cannot be performed.  
● The recording tape’s Erase Protection tab is missing.  
Cover the hole with adhesive tape. (Some tapes have  
sliding tabs. In this case, check the position of the tab.)  
Recording does not start.  
● The camcorder power switch has not been set to  
CAMERA (੬ pg. 14).  
PLAYBACK  
The tape is running, but there’s no  
playback picture.  
● The TV has not been set to its VIDEO mode or channel.  
● If A/V connection is used, the TV’s VIDEO/TV switch has  
not been set to VIDEO.  
● The RF unit has not been set to the correct channel.  
Noise bars appear in the playback  
picture.  
● Manual Tracking has not been performed (੬ pg. 31).  
Playback picture is blurred or  
interrupted.  
● The video heads are dirty or worn out. Consult your  
nearest JVC dealer for head cleaning or replacement.  
The counter indication is blurred  
during Still playback.  
● This is normal.  
TAPE TRANSPORT  
The tape stops during fast-forward or  
rewind.  
● The Counter Memory Function has been activated  
(੬ pg. 31).  
Rewinding or fast-forwarding cannot  
be performed.  
● The tape is already fully wound on one reel or the other.  
OTHER  
The tape won’t eject.  
Some functions are not available.  
● The battery pack is running low.  
● The PROGRAM AE dial is set to LOCK (੬ pg. 16).  
Vertical white lines appear when  
shooting a very bright object.  
● This sometimes occurs when the contrast between the  
background and the object is great. It is not a defect of  
the camcorder.  
Bright, crystal-shaped spots appear  
in the viewfinder.  
● Sunlight is directly entering the lens.  
The picture is blurred in the Quick  
Review or Retake mode.  
● This is normal while recording in the EP mode. Some noise  
may be present while recording in the SP mode (੬pg. 11).  
An error number (E01, etc.) appears  
in the viewfinder.  
● Consult your nearest JVC dealer.  
The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might  
prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Power  
Adapter/Battery Charger, etc.) and clock battery; and then re-connect it and proceed as usual from the beginning.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INDEX Controls  
40  
0 ! @ # $%  
Controls  
1 PROGRAM AE Select Dial .................. ੬ pg. 16  
2 F1 [Function 1] Button ........................੬ pg. 18  
3 PUSH Button....................................... ੬ pg. 11  
4 Function SEL. Button ........................... ੬ pg. 18  
5 F2 [Function 2] Button ........................੬ pg. 18  
6 EJECT Switch ....................................... ੬ pg. 11  
7 Diopter Adjustment ............................. ੬ pg. 11  
8 Power Zoom Switch ............................ ੬ pg. 15  
9 BATT. [Battery] RELEASE Switch ............ ੬ pg. 8  
t
R
T 7 Y 8  
^ &*( )  
0 MWB [Manual White Balance]  
U
I
Button ................................................. ੬ pg. 17  
! Recording Mode [SP/EP] Select  
Button ................................................. ੬ pg. 11  
Tape Length [T20•T30•T40]  
Select Button ....................................... ੬ pg. 11  
COUNTER R [Reset]/M [Memory]  
Button ................................................. ੬ pg. 31  
@ EDIT Button ........................................ ੬ pg. 32  
9
y
u i o q w Q  
O
# DATE/TIME +/– Buttons ....................... ੬ pg. 10  
CHAR. [Character] SET +/– Buttons ..... ੬ pg. 24  
TRACKING +/– Buttons ....................... ੬ pg. 31  
$ DATE/TIME SET Button ........................੬ pg. 10  
CHAR. SET Button............................... ੬ pg. 24  
R.A.EDIT IN/OUT Button .................... ੬ pg. 34  
% R.A.EDIT Button .................................. ੬ pg. 34  
^ REW Button ........................................ ੬ pg. 30  
RETAKE R [Quick Review] Button ....... ੬ pg. 15  
& FF Button ............................................੬ pg. 30  
RETAKE F Button .................................੬ pg. 15  
* R.A.EDIT CANCEL Button ................... ੬ pg. 34  
( STOP Button ....................................... ੬ pg. 30  
) PLAY/PAUSE Button ............................ ੬ pg. 30  
q POWER Switch ...................................੬ pg. 10  
w Recording Start/Stop Button................ ੬ pg. 12  
e LIGHT ON/AUTO/OFF select switch ......੬ pg. 18  
P
W 1 2  
3
6
r
E
p
4 5  
e
Other Parts  
W Microphone  
E Infrared beam sensor window ............. ੬ pg. 13  
(Be careful not to cover this area; built-in here is  
the sensor necessary for shooting.)  
R Clock Battery Compartment ................ ੬ pg. 10  
T Battery Pack Mount ...............................੬ pg. 8  
Y Electronic Viewfinder .......................... ੬ pg. 11  
U LENS COVER Switch ........................... ੬ pg. 14  
I Grip Strap ........................................... ੬ pg. 12  
O Tripod Mounting Socket ...................... ੬ pg. 12  
P Video Light.......................................... ੬ pg. 18  
Connectors  
r REMOTE Jack (For connection of the RM-V20U  
wired remote control unit (optional).)  
t Shoulder Strap Eyelets ......................... ੬ pg. 12  
y EDIT Jack ............................................੬ pg. 32  
u VIDEO Out Jack .................................. ੬ pg. 29  
i RF DC OUT Jack .................................੬ pg. 29  
o AUDIO Out Jack .................................੬ pg. 29  
Indicators  
p Tally Lamp .......................................... ੬ pg. 14  
Q Power On Indicator............................. ੬ pg. 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INDEX Viewfinder  
41  
6 7 8 9  
0
!
T
30 SP  
T
30MIN  
F2  
REC  
CINEMA  
F1  
FADER  
@
#
$
%
^
&
*
PAUSE  
SPORTS  
LENS COVER  
1
s
2
3
4
MWB  
W
INDEX  
FADER  
1 4S  
5MIN  
5
MERRY CHR ISTMAS  
AM 10 : 55  
DEC 25.96  
( )  
q
w
Viewfinder Indications  
1, 2 PROGRAM AE Indicator ................ ੬ pg. 16  
Displayed at 2 for approx. 3 seconds when the  
PROGRAM AE select dial is switched from one  
position to another. Then only the indicator  
remains at 1.  
3 Focus Indicator ...................................੬ pg. 20  
4 White Balance Mode Indicator............ ੬ pg. 17  
5 Zoom Level Indicator ..........................੬ pg. 15  
Exposure Indicator Bar ........................੬ pg. 22  
! Recording Mode (SP/EP) Indicator ....... ੬ pg. 11  
@ Recording Indicator ............................. ੬ pg. 14  
# Record–Standby Indicator ................... ੬ pg. 14  
$ Lens Cover Warning ............................ ੬ pg. 14  
% Index Code Marking............................ ੬ pg. 15  
^ Fade–Standby Indicator ....................... ੬ pg. 19  
& Clock Battery Warning  
Appears when the clock (lithium) battery is not  
in place or exhausted.  
6 Battery Pack Remaining Power Indicator  
Changes as follows according to the battery  
pack’s remaining power level:  
For inserting or replacing the  
clock battery ....................................... ੬ pg. 10  
* Insert Editing Indicator ........................ ੬ pg. 36  
Audio Dubbing Indicator .................... ੬ pg. 37  
“
”. When the power is  
almost gone, the indicator blinks, then the unit  
shuts off. Replace the battery pack with a fully  
charged one ..........................................੬ pg. 8  
( Condensation Warning  
When this indicator appears, all functions are  
disabled. Turn the unit off for a few hours, and  
when you turn it on again the indicator should  
disappear.  
7 Cassette Warning ................................ ੬ pg. 11  
Blinks when no cassette or a cassette with the  
Erase Protection tab removed is loaded.  
8 Intelligent Function Control  
Indicator ............................................. ੬ pg. 18  
9 Remaining Tape Time ..........................੬ pg. 14  
) Instant Title ......................................... ੬ pg. 25  
q Date/Time/Character ........................... ੬ pg. 23  
w Interval  
0 Tape Length Indicator .......................... ੬ pg. 11  
Time/Recording Time Indicator ........... ੬ pg. 26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INDEX Terms  
42  
A
N
AC Power Adapter .................................. pg. 9  
ND Effect Mode ...................................... pg. 16  
Animation Recording .............................. pg. 27  
Audio Dubbing ....................................... pg. 37  
Auto Date Record ................................... pg. 23  
Auto Focus.............................................. pg. 20  
Auto Mode Lock Mode ........................... pg. 16  
Auto Mode Release Mode ....................... pg. 16  
O
On-Screen Display.................................. pg. 23  
P
Playback ................................................. pg. 30  
Program AE with Special Effects .............. pg. 16  
Provided Accessories .............................. pg. 6  
B
Battery Pack ............................................ pg. 8, 43  
Brighten the Image .................................. pg. 22  
Q
Quick Review ......................................... pg. 15  
C
R
Car Battery .............................................. pg. 9  
Cassette Adapter ..................................... pg. 28  
Character Generator ............................... pg. 24  
Charge Marker ........................................ pg. 9  
Charging the Battery Pack ....................... pg. 8  
Cinama Mode ......................................... pg. 19  
Clock (Lithium) Battery ........................... pg. 10  
Connection to a VCR/TV ......................... pg. 29  
Contents ................................................. pg. 7  
Counter Memory ..................................... pg. 31  
Random Assemble Editing ....................... pg. 32–35  
Recording, Advanced Features ................ pg. 16–27  
Recording ............................................... pg. 14  
Recording, Start/Stop............................... pg. 14  
Recording Mode Setting.......................... pg. 11  
Recording-Standby.................................. pg. 14  
Remote Control Unit ............................... pg. 13  
Remove Cassette ..................................... pg. 11  
Retake..................................................... pg. 15  
Rewind Tape ........................................... pg. 30  
D
S
Darken the Image ................................... pg. 22  
Date/Time Insert...................................... pg. 23  
Date/Time Setting.................................... pg. 10  
Discharge the Battery pack...................... pg. 8  
Diopter Adjust......................................... pg. 11  
Self-Timer ............................................... pg. 16, 26  
Sepia Mode............................................. pg. 16  
Shoulder Strap Attachment ...................... pg. 12  
Shuttle Search ......................................... pg. 31  
Specifications.......................................... pg. 45  
Sports Mode............................................ pg. 16  
Still Playback .......................................... pg. 31  
E
Electronic Fog Filter Mode ...................... pg. 16  
Erase Protection ...................................... pg. 11  
Exposure Control .................................... pg. 22  
T
Tape Counter .......................................... pg. 30  
Tape Dubbing ......................................... pg. 32  
Tape Length Setting ................................. pg. 11  
Time-Lapse Shooting ............................... pg. 27  
Tracking .................................................. pg. 31  
Tripod Mounting ..................................... pg. 12  
Twilight Mode ......................................... pg. 16  
F
Fade-in/out ............................................. pg. 19  
Fast-Forward Tape ................................... pg. 30  
Focus Lock.............................................. pg. 20  
G
Grip Adjustment...................................... pg. 12  
V
H
Video Light ............................................. pg. 18  
Viewfinder Adjustment ............................ pg. 11  
Viewfinder, Indications............................ pg. 41  
High Speed Shutter Mode ....................... pg. 16  
I
W
Index Code Marking ............................... pg. 15  
Insert Cassette ......................................... pg. 11  
Insert Editing ........................................... pg. 36  
Instant Titles ............................................ pg. 25  
Intelligent Function Control .................... pg. 18–25  
White Balance Adjustment ...................... pg. 17  
Z
Zooming ................................................. pg. 15  
M
Manual Focus ......................................... pg. 21  
Master Edit Control ................................. pg. 32  
MBR code Setting ................................... pg. 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTIONS  
43  
DANGER:  
General Battery Precautions  
Video Light  
•When the RM-V20U (remote control), C-P6U or  
C-P7U (cassette adapter) are not functioning even  
when correctly operated, the batteries are  
exhausted. Replace them with fresh ones.  
•Use only the following batteries:  
RM-V20U ................................. AAA (R03) size  
C-P6U or C-P7U ....................... AA (R6) size  
• The video light becomes extremely hot. Do not touch it  
either while in operation or soon after turning it off,  
otherwise serious injury may result.  
• Do not place the camcorder into the carrying case  
immediately after using the video light, since it remains  
extremely hot.  
• When operating, keep a distance of about 30 cm  
(1 ft.) between the video light and people or object.  
• Do not us e near flammable or explosive materials.  
Please make note of the following rules for battery  
use. When misused, batteries can leak or explode.  
Serious malfunctioning  
1. Refer to the RM-V20U and C-P6U/C-P7U  
instructions when replacing batteries.  
2. Do not use old and new batteries together.  
3. Do not use two different kinds of batteries.  
Although sizes may be the same, voltages may  
differ.  
4. Do not expose batteries to excessive heat as they  
can leak or explode.  
5. Do not dispose of batteries in a fire.  
6. Remove batteries from the unit if it is to be stored  
for an extended period to avoid battery leakage  
which can cause malfunctions.  
If malfunctioning occurs, stop using the unit  
immediately and consult your local JVC dealer.  
When using the AC Power Adapter/Charger in  
areas other than the USA  
Ⅲ The provided AC Power Adapter/Charger features  
automatic voltage selection in the AC range from 110 V  
to 240 V.  
USING HOUSEHOLD AC PLUG ADAPTER  
In case of connecting the unit's power cord to an AC wall  
outlet other than American National Standard C73 series  
type use an AC plug adapter, called a "Siemens Plug", as  
shown.  
Battery Packs  
For this AC plug adapter, consult your nearest JVC dealer.  
The supplied battery pack is a  
nickel-cadmium battery. Before  
using the supplied battery pack or  
an optional battery pack, be sure to  
read the following cautions:  
Plug adapter  
INFORMATION  
This device complies with Part 15 of FCC Rules. Operation  
is subject to the following two conditions:  
1. To avoid hazard . . .  
...... do not burn.  
Terminals  
(1) This device may not cause harmful interference, and (2)  
this device must accept any interference received,  
including interference that may cause undesired operation.  
Change or modifications not approved by the party  
responsible for compliance could void the user's authority  
to operate the equipment. This equipment has been tested  
and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against  
harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with  
the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that  
interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio  
or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to  
try to correct the interference by one or more of the  
following measures:  
...... do not short-circuit the terminals.  
...... do not modify or disassemble.  
...... use only specified chargers.  
2. To prevent damage and prolong service  
life . . .  
...... do not subject to unnecessary shock.  
...... avoid repeated charging without fully discharging.  
...... charge in an environment where  
temperatures are within the tolerances shown in the  
chart below. This is a chemical reaction type  
battery—cooler temperatures impede chemical  
reaction, while warmer temperatures can prevent  
complete charging.  
...... store in a cool, dry place. Extended exposure to  
high temperatures will increase natural  
discharge and shorten service life.  
...... avoid prolonged uncharged storage.  
...... remove from charger or powered unit when not in  
use, as some machines use current even when  
switched off.  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and  
receiver.  
Connect the equipment into an outlet on a circuit  
different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician  
for help.  
3. To prevent damage to the camcorder . . .  
...... replace the battery pack when it begins to deliver  
less recording time per charge.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTIONS (cont.)  
44  
3. DO NOT leave the unit . . .  
NOTE:  
...... in places of over 50°C (122°F).  
...... in places where humidity is extremely low (below  
35%) or extremely high (above 80%).  
...... in direct sunlight.  
It is normal for the battery pack to be warm after charging,  
or after use.  
Temperature Range Specifications  
Charging .......................................... 10°C to 35°C  
Operation ........................................ 0°C to 40°C  
Storage ............................................. –10°C to 30°C  
...... in a closed car in summer.  
...... near a heater.  
4. To protect the unit, DO NOT . . .  
...... allow it to become wet.  
...... drop the unit or strike it against hard objects.  
...... subject it to shock or excessive vibration during  
transportation.  
NOTES:  
● Recharging time is based on room temperature of 20°C.  
● The lower the temperature, the longer recharging takes.  
...... keep the lens directed at extremely bright objects  
for long periods.  
...... direct the eyepiece of the viewfinder at the sun.  
...... carry it by holding the viewfinder.  
...... swing it excessively when using the shoulder strap.  
Cassettes  
To properly use and store your cassettes, be sure to  
read the following cautions:  
1. During use . . .  
5. This camcorder features a built-in head  
cleaner which automatically cleans the  
heads and head drum when a cassette is  
loaded or unloaded. If, however, the heads  
become dirty and cause blurriness or  
interruption in the playback picture,  
consult your nearest JVC dealer.  
...... make sure the cassette bears the VHS-C mark.  
...... be aware that recording onto prerecorded tapes  
automatically erases the previously recorded  
video and audio signals.  
...... make sure the cassette is positioned properly when  
inserting.  
...... do not load and unload the cassette  
repeatedly without allowing the tape to run at all.  
This slackens the tape and can result in damage.  
...... do not open the front tape cover. This exposes the  
tape to fingerprints and dust.  
About moisture condensation . . .  
• You have observed that pouring a cold liquid into a glass  
will cause drops of water to form on the glass‘ outer  
surface. This same phenomenon occurs on the head  
drum of a camcorder when it is moved from a cool place  
to a warm place, after heating a cold room, under  
extremely humid conditions or in a place directly  
subjected to the cool air from an air conditioner.  
• Moisture on the head drum can cause severe damage to  
the video tape, and can lead to internal damage to the  
camcorder itself.  
2. Store cassettes . . .  
...... away from heaters or other heat sources.  
...... out of direct sunlight.  
...... where they won’t be subject to unnecessary shock  
or vibration.  
...... where they won’t be exposed to strong magnetic  
fields (such as those generated by motors,  
transformers or magnets).  
...... vertically, in their original cases.  
Main Unit  
1. For safety, DO NOT . . .  
...... open the camcorder’s chassis.  
...... disassemble or modify the unit.  
...... short-circuit the terminals of the battery pack. Keep  
it away from metallic objects when not in use.  
...... allow inflammables, water or metallic objects to  
enter the unit.  
...... remove the battery pack or disconnect the power  
supply while the power is on.  
...... leave the battery pack attached when the  
camcorder is not in use.  
2. Avoid using the unit . . .  
...... in places subject to excessive humidity or dust.  
...... in places subject to soot or steam such as near a  
cooking stove.  
...... in places subject to excessive shock or vibration.  
...... near a television set.  
...... near appliances generating strong magnetic or  
electric fields (speakers, broadcasting antennas,  
etc.).  
...... in places subject to extremely high (over 40°C or  
104°F) or extremely low (under 0°C or 32°F)  
temperatures.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
GENERAL  
45  
VIDEO  
Output  
Format  
: VHS NTSC standard  
: 1 Vp-p, 75 ohms,  
Power source  
Power consumption  
Video light off  
Video light  
: DC 6V  
unbalanced (via VIDEO  
out connector)  
: 5.9 W  
: 3 W  
: NTSC-type  
AUDIO  
Output  
Signal system  
Video recording system  
Luminance  
: –8 dBs, 1 k-ohm  
(via AUDIO out  
connector)  
: FM recording  
: Converted sub-carrier  
direct recording  
* Conforms to VHS  
standard  
Color  
AC POWER ADAPTER/BATTERY CHARGER  
(AA-V11U)  
Power requirement  
Cassette  
Tape speed  
SP  
:
cassette  
U.S.A. and Canada : AC 120 V`, 60 HZ  
Other countries  
: AC 110 V to  
240 V`, 50/60 Hz  
: 23 W  
: 33.35 mm/sec.  
(1-5/16 ips)  
: 11.12 mm/sec. (7/16 ips)  
Power consumption  
Output  
Charge  
VTR  
Charging system  
EP  
Recording time (max.)  
: DC 8.5 V  
: DC 6.3 V  
, 1.3 A  
, 1.8 A  
: Constant current, peak  
detection, timer  
controlled  
SP  
EP  
: 40 minutes  
: 120 minutes  
(with TC-40 cassette)  
Operating temperature : 0°C to +40°C  
(32°F to 104°F)  
Dimensions  
: 150 (W) x 42 (H) x  
68 (D) mm  
Operating humidity  
Storage temperature  
: 35% to 80%  
: –20°C to +50°C  
(–4°F to 122°F)  
: Approx. 740 g (1.7 lbs)  
: 109 (W) x 113 (H) x 206  
(D) mm (4-5/16" x 4-1/2"  
x 8-1/8"  
(5-15/16" x 1-11/16" x  
2-11/16")  
: Approx. 320 g (0.71 lbs)  
Weight  
Dimensions  
(Including viewfinder)  
Weight  
CASSETTE ADAPTER (C-P7U)  
Dimensions  
: 188 (W) x 25 (H) x  
104 (D) mm  
(7-7/16" x 1" x 4-1/8")  
: Approx. 240 g (0.53 lbs)  
: “AA (R6)”-size battery x 1  
CAMERA  
Pick up  
Lens  
Weight  
: 1/4" format CCD  
Accessory  
: F1.2, f = 4.1 to 57.4 mm,  
14:1 power zoom lens  
with auto iris and macro  
control, filter diameter  
46 mm  
Provided Accessories ...................... ੬ pg. 6  
Optional Accessories  
•Battery Packs BN-V12U, BN-V22U, BN-V25U  
•Car Battery Charger BH-V3U  
•Battery Charger BH-VC10U  
Viewfinder  
: Electronic viewfinder  
with 0.55" color LCD  
White balance  
adjustment  
•Car Battery Cord AP-V7U  
: Auto/Manual adjustment  
•RF Unit RF-V5U  
•Wireless Remote Control Unit RM-V700U  
•Wired Remote Control Unit RM-V20U  
•Compact VHS-C Cassettes TC-40/30/20  
•Active Carrying Bag CB-V7U  
* Some acccessories are not available in some  
areas. Please consult your nearest JVC dealer for  
details on accessories and their availability.  
Specifications shown are for SP mode unless  
otherwise indicated. E. & O. E. Design and  
specifications subject to change without notice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPAÑOL  
46  
Alimentación  
Indicador CHG. (carga)  
Marcas  
Esta cámara de video posee un sistema de alimentación de 3 vías  
que le permite seleccionar la fuente de alimentación más  
apropiada.  
Al  
tomacorriente  
de alterna  
Indicador  
POWER  
NOTAS:  
● Sin alimentación no hay ninguna función disponible.  
● Utilice exclusivamente la alimentación indicada.  
● No utilice la unidades de alimentación suministradas con otro  
equipo.  
Indicador  
END  
CARGA DEL PAQUETE DE PILAS  
ALIMENTACION  
Conecte el cordón de alimentación de CA del  
cargador a un tomacorriente. Se encenderá la luz  
1
delindicador de alimentación.  
Interruptor REFRESH  
Indicador REFRESH  
COLOCACION DEL PAQUETE DE PILAS  
Alinee las marcas y deslice el paquete de pilas en la  
Enganche.  
dirección de la flecha hasta que quede bloqueado  
2
en su lugar.  
Se enciende la luz indicadora CHG.  
EXTRACCION DEL PAQUETE DE PILAS  
Cuando la carga está completa, se encenderá el  
indicador END. Deslice el paquete de pilas en el  
3
sentido opuesto al de la flecha.  
Empuje.  
BATT. RELEASE  
PAQUETE  
DE PILAS  
CARGA  
DESCARGA  
aprox.  
3 horas 30 min.  
aprox.  
BN-V11U  
aprox. 1 hora 10 min.  
aprox. 1 hora 10 min.  
Marcador  
de carga  
BN-V12U  
3 horas 30 min.  
BN-V22U  
BN-V25U  
aprox. 2 horas 10 min.  
aprox. 2 horas 40 min.  
aprox. 7 horas  
aprox. 10 horas  
USO DEL PAQUETE DE PILAS  
COLOCACION DEL PAQUETE DE PILAS  
Enganche la parte superior del mismo en la cámara  
de video y empuje el paquete de pilas hasta que se  
bloquee en su lugar.  
1
2
**INDICADOR DE CARGA  
Se ha suministrado un indicador de carga  
sobre el paquete de pilas para ayudarle a  
recordar si ha sido cargado o no. Los dos  
colores suministrados (rojo y negro), le  
permiten seleccionar la carga y la descarga.  
EXTRACCION DEL PAQUETE DE PILAS  
Deslice BATT. RELEASE y extraiga el paquete de  
pilas.  
TIEMPO DE GRABACION  
**REFRESCADO  
PAQUETE  
Luz encendida  
DE PILAS  
Luz apagada  
El adaptador de CA se caracteriza por la  
función REFRESH que le permite descargar  
totalmente el paquete de pilas antes de  
recargarlo.  
BN-V11U  
BN-V12U  
BN-V22U  
BN-V25U  
aprox. 1 hora  
aprox. 1 hora  
aprox. 35 min.  
aprox. 35 min.  
aprox. 2 horas 10 min. aprox. 1 hora 20 min.  
aprox. 2 horas 50 min. aprox. 1 hora 50 min.  
Para descargar las pilas . . .  
..... coloque el paquete de pilas en el adaptador  
como se muestra en la ilustración de la  
izquierda. Luego presione REFRESH. El  
indicador REFRESH se enciende cuando se  
inicia la descarga y se apaga cuando la descarga  
ha terminado.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIA PARA OPERACION RAPIDA  
Si la unidad comienza a funcionar mal, deje de usarla inmediatamente y consulte a su concesionario local de JVC.  
47  
ALIMENTACION  
INSERCION DEL CASSETTE  
DE VIDEOEO  
Enganche.  
1
EJECT (eyección)  
1
Empuje.  
2
3
PUSH  
2
(presione)  
Inserte.  
BATT. RELEASE (extracción de la batería)  
Utilización de la batería  
1 Enganche el extremo superior de la batería  
en la cámara de video. (Procedimiento para  
carga: ੬ P. 8)  
1 Deslice EJECT.  
2 Inserte un cassette de video.  
3 Presione PUSH.  
2 Empuje la batería hacia adentro hasta que  
(Por más detalles, ੬ P. 11.)  
quede bloqueada en su lugar.  
Para extraer la batería  
Deslice BATT. RELEASE y extraiga la batería.  
REPRODUCCION  
FILMACION  
PLAY/PAUSE  
3
(reproducción/pausa)  
REW  
2
(rebobinado)  
1
Perilla de  
abertura/cierre  
LENS COVER  
2
STOP  
Colóquelo en “CAMERA”.  
(parada)  
3
Botón para inicio/parada de  
grabación  
1
Colóquelo en “PLAY”.  
1 Deslice la perilla de abertura/cierre LENS  
COVER para abrir la tapa del objetivo.  
2 Adjuste el interruptor de alimentación en  
“CAMERA”.  
— El indicador de alimentación se  
encenderá y aparecerá una imagen en el  
visor.  
1 Ajuste el interruptor de alimentación en  
“PLAY”.  
2 Presione REW.  
— La cinta se detiene automáticamente al  
comienzo de la misma.  
3 Presione PLAY/PAUSE.  
— Comienza la reproducción y la imagen  
aparece en el visor.  
•Presione STOP para detener la grabación.  
(Por más detalles, ੬ P. 30.)  
3 Presione el botón inicio/parada de  
grabación.  
— Comenzará la grabación.  
•Para detener temporariamente la grabación,  
presione nuevamente el botón de inicio/  
parada de grabación.  
Ⅲ O simplemente reproduzca la cinta en un  
VCR de VHS utilizando el adaptador de  
cassette (VHS Playpak). ੬ P. 28  
(Por más detalles, ੬ P. 14.)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FOR SERVICING  
HOW TO LOCATE YOUR JVC SERVICE CENTER  
48  
TOLL FREE: 1-800-252-5722  
Dear customer:  
In order to receive the most satisfaction from your purchase, read the instruction booklet before  
operating the unit. In the event that repair is necessary, or for the address nearest your location,  
please refer to the factory service center list below or within the Continental United States, call 1-800-  
252-5722 for your authorized servicer. Remember to retain your Bill of Sale for Warranty Service.  
— JVC  
JVC SERVICE & ENGINEERING  
COMPANY OF AMERICA  
DIVISION OF US JVC CORP.  
FACTORY SERVICE CENTER LOCATIONS  
107 Little Falls Road  
Fairfield, NJ 07004-2105  
(201) 808-9279  
1500 Lakes Parkway  
Lawrenceville, GA 30243-5357  
(770) 339-2522  
705 Enterprise Street  
Aurora, IL 60504-8149  
(708) 851-7855  
5665 Corporate Avenue  
Cypress, CA 90630-0024  
(714) 229-8011  
10700 Hammerly, Suite 110  
Houston, TX 77043-2310  
(713) 935-9331  
2969 Mapunapuna Place  
Honolulu, HI 96819-2040  
(808) 833-5828  
230 Eliot Street  
Ashland, MA 01721-2377  
(508) 881-5923  
14505 Commerce Way  
Miami Lakes, FL 33016-1512  
(305) 362-6252  
890 Dubuque Avenue  
South San Francisco, CA 94080-1804  
(415) 871-2666  
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the  
engineering and production of the wide array of JVC products, service is the key to maintaining the  
high level performance for which JVC is world famous. The JVC service and engineering organization  
stands behind our products.  
NATIONAL HEADQUARTERS  
JVC SERVICE & ENGINEERING COMPANY OF AMERICA  
DIVISION OF US JVC CORP.  
107 Little Falls Road  
Fairfield, NJ 07004-2105  
If you ship the product...  
Pack your JVC unit in the original carton or one of equivalent size and strength. Enclose, with the unit,  
a letter stating the problem or symptom that exists and also a copy of the receipt or bill of sale you  
received when you purchased your JVC unit. Print your home return address on the outside and the  
inside of the carton. Send to the appropriate JVC Factory Service Center as listed above.  
Don't service it yourself.  
ACCESSORIES  
To purchase accessories for your JVC product, you  
may contact your local JVC Dealer.  
Or from the 48 Continental United States call toll free:  
1-800-882-2345.  
CAUTION  
To prevent electrical shock, do not open the  
cabinet. No user serviceable parts inside.  
Refer servicing to qualified service personnel.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY  
49  
LIMITED WARRANTY  
CONSUMER VIDEO 1-90  
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO  
THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP  
from the date of original retail purchase for the period as shown below. ("The Warranty Period")  
PARTS  
LABOR  
1
YR  
90  
DAYS  
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF  
COLUMBIA AND IN COMMONWEALTH OF PUERTO RICO.  
WHAT WE WILL DO:  
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner.  
Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized  
service centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All  
products and parts thereof may be brought to a JVC authorized service center on a carry-in basis except for  
Television sets having a screen size 25 inches and above which are covered on an in-home basis.  
WHAT YOU MUST DO FOR WARRANTY SERVICE:  
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC  
authorized service center, please call toll free: (800) 252-5722.  
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with  
a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center,  
the name and location of which will be given to you by the toll-free number.  
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.  
WHAT IS NOT COVERED:  
This limited warranty provided by JVC does not cover:  
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse,  
faulty installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility  
authorized by JVC to render such service, or if affixed to any attachment not provided with the products, or if  
the model or serial number has been altered, tampered with, defaced or removed;  
2. Initial installation and installation and removal for repair;  
3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;  
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;  
5. Signal reception problems and failures due to line power surge;  
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of  
purchase;  
7. Accessories;  
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);from the date  
of purchase);  
There are no other express warranties except as listed above.  
THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF  
MERCHANTABILITY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.  
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY  
OTHER DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT  
LIMITATION, DAMAGE TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT,  
OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES,  
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE  
LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.  
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an  
implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific  
legal rights and you may also have other rights which vary from state to state.  
JVC COMPANY OF AMERICA  
DIVISION OF US JVC CORP.  
41 Slater Drive  
Elmwood Park, New Jersey 07407  
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR  
DETAILS OF REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT  
WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.  
For customer use:  
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain  
this information for future reference.  
Model No.:  
Serial No:  
Purchase date:  
Name of dealer:  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MEMO  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MEMO  
Download from Www.Somanuals.com. All Manuals Search And Download.  
JVC COMPANY OF AMERICA  
DIVISION OF US JVC CORP.  
41 Slater Drive, Elmwood Park, N.J. 07407  
0P5ri9n6teMdKinV*JaUpNan*YP  
U
COPYRIGHT© 1996 VICTOR COMPANY OF JAPAN, LTD.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Infinity Speaker System P252 User Manual
Intel Portable Speaker Fireface 800 User Manual
JBL Portable Speaker M9500 User Manual
Jet Tools Saw JTAS 10XL50 1DX User Manual
Kawasaki Motorcycle VN900 User Manual
KitchenAid Microwave Oven W10189714A User Manual
KitchenAid Patio Furniture KSBN220SSS User Manual
Klipsch Home Theater System KHC 6 User Manual
Kodak Camera Accessories KAI 02150 User Manual
Kolcraft Stroller S45J R7 User Manual