JVC CRT Television HV 32D25EJ User Manual

Colour Television

HV-32D25EJ

Contents

Setting up your TV. . . . . . . . . . . . . . . . . 5

TV buttons and functions. . . . . . . . . . . 10

Remote control buttons and functions. . 11

Teletext function . . . . . . . . . . . . . . . . . 19

Using the TV’s menu . . . . . . . . . . . . . . 22

Additional menu operations. . . . . . . . . 47

Additional preparation . . . . . . . . . . . . . 50

Troubleshooting. . . . . . . . . . . . . . . . . . 55

Specifications . . . . . . . . . . . . . . . . . . . 57

INSTRUCTIONS

LCT1271-001A-U

1002-T-CR-JMUK

Download from Www.Somanuals.com. All Manuals Search And Download.

Thank you for buying this JVC colour television.

To make sure you understand how to use your new TV, please read this manual thoroughly before you

begin.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

• Operate only from the power source specified

(AC 220 – 240 V, 50 Hz) on the unit.

• Avoid damaging the AC plug and power cord.

• The main power button on the TV does not

fully isolate the TV from the mains supply. If

you are not going to use this TV for a long

period of time, be sure to disconnect the mains

plug from the mains outlet.

Avoid improper installation and never put the unit where good

ventilation is not possible.

When installing this TV, distance recommendations must be

maintained between the set and the wall, as well as inside a tightly

enclosed area or piece of furniture.

Adhere to the minimum distance guidelines shown for safe operation.

Failure to heed the following precautions may result in damage to the TV or

remote control.

DO NOT block the TV’s ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be

able to get out.)

DO NOT place anything on top of the TV.

(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)

DO NOT allow objects or liquid into the cabinet openings.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

DO NOT place any naked flame sources, such as lighted candles, on the TV.

The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.

Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.

Never use any cleaner or detergent on it.

In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it

yourself or remove the rear cover.

Download from Www.Somanuals.com. All Manuals Search And Download.

„

Warning

DO NOT cut off the mains plug from this

equipment. If the plug fitted is not suitable

for the power points in your home or the

cable is too short to reach a power point, then

obtain an appropriate safety approved

extension lead or adaptor or consult your

dealer.

As these colours may not correspond with the

coloured marking identifying the terminals in

your plug proceed as follows:

The wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black.

The wire which is coloured brown must be

connected to the terminal which is marked

with the letter L or coloured red.

If nonetheless the mains plug is cut off,

remove the fuse and dispose of the plug

immediately, to avoid a possible shock

hazard by inadvertent connection to the

mains supply.

When replacing the fuse, use only a correctly

rated approved type and always re-fit the fuse

cover.

If a new mains plug has to be fitted, then

follow the instruction given below:

„ If in doubt — consult a competent

electrician.

Important

Do not make any connection to the larger

terminal which is marked with the letter E or

How to replace the fuse

Open the fuse

compartment with a

by the safety earth symbol

green or green-and-yellow.

or coloured

blade screwdriver, and

replace the fuse.

The wires in the mains lead on this product

are coloured in accordance with the

following code:

Fuse

Blue: Neutral

Brown: Live

„

Guidelines for safe operation

This equipment has been designed and manufactured to comply with international safety

standards. However, as with any electrical appliance, care must be taken to ensure optimal results

and operational safety.

• Before attempting to use this equipment, read the operating instructions thoroughly.

• Ensure that all electrical connections (including the mains plug, extension leads, etc.) have

been made in accordance with the manufacturer’s instructions.

• If ever in doubt about the installation, operation or safety of this equipment, consult your

dealer.

• Handle all glass panels or covers with care.

• Never operate this equipment if it appears damaged or operates abnormally. Turn the power

off, disconnect the main power plug and consult your dealer.

• Never remove any affixed panels or covers. Doing so may result in electrical shock.

• Never leave this equipment operating unattended unless otherwise specifically stated that it is

designed to do so or in standby mode. Only use the designated power switch to turn off the

power and ensure that all potential users are instructed how to do so. Make special

arrangements for infirm or handicapped persons.

• Never watch TV while operating a motor vehicle. It is illegal to watch TV while driving.

• Never listen to headphones at high volume. Doing so may damage your hearing.

Download from Www.Somanuals.com. All Manuals Search And Download.

• Never obstruct the ventilation of this equipment. Doing so may cause overheating and result in

a malfunction or damage.

• Never use makeshift stands or attempt to affix legs with wood screws. When using a

manufacturer’s approved stand or legs, use only the fixtures provided and follow the

installation instructions.

• Never allow this equipment to be exposed to rain or moisture.

• Never allow anyone, especially children, to insert anything into an opening in the case. Doing

so may result in a fatal electrical shock.

• Never guess or take chances with electrical equipment of any kind. It is better to be safe than

sorry.

Caution

• The woofer unit is mounted on the TV. Always move the TV and woofer unit together when

removing the TV from the box, or when moving the woofer unit.

• If the TV is tilted during movement the woofer unit may fall. Be careful to keep the TV level

when moving it.

• Do not grip the woofer unit when moving the TV.

• Do not place objects on the woofer unit duct.

LIFTING CAUTION

FREE WOOFER UNIT

KEEP WITH UNIT

D.I.S.T. demonstration

To start the D.I.S.T. demonstration:

Press the a button to display the MENU (main menu). Then press the yellow button.

A picture split in two ( D.I.S.T. turned on and D.I.S.T. turned off ) will appear on the screen.

To quit the D.I.S.T. demonstration:

Press the yellow button, b button, P p buttons or any of the number buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up your TV

Caution

• Turn off all the equipment including the TV before connecting anything.

Connecting the aerial and video cassette recorder (VCR)

• The connecting cables are not provided.

• For further details, refer to the manuals provided with the devices to be connected.

„ If you are connecting a VCR,

follow A → B → C in the diagram

opposite.

Aerial

„ If you are not connecting a VCR,

follow 1.

75-ohm

Coaxial

Cable

To use the T-V LINK functions, you must

have a T-V LINK compatible VCR

connected by a SCART cable C to the EXT-

2 terminal on the TV. For details about T-V

LINK functions, see “T-V LINK functions”

on page 8.

Back of the TV

• You can watch a video using the VCR

without doing C. For details, see your

VCR instruction manual.

• To connect more equipment, please see

“Connecting external equipment” on

page 50.

21-pin

SCART

Cable

75-ohm

Coaxial

Cable

• To connect additional audio equipment,

see “Using additional audio equipment”

on page 52.

To Aerial

Input

VCR

• To connect a device (such as DVD player)

with the digital output terminal for Dolby

Digital, see “Listening to Dolby Digital

audio” on page 52.

• If you connect a decoder to a T-V LINK

compatible VCR, set the DECODER

(EXT-2) function to ON. For details, see

“Using the DECODER (EXT-2)

function” on page 48.

To Aerial

Output

AV IN/OUT

Terminal

Otherwise, you will not be able to watch

scrambled channels.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up your TV

„ Rear Panel

1 Woofer terminal (page 54)

2 AUDIO OUT terminal (page 53)

3 SURROUND REAR terminal (page 53)

4 EXT-1 terminal (pages 5, 36, 50)

5 EXT-2 terminal (pages 5, 8, 36, 50)

6 EXT-3 terminal (pages 36, 50)

7 EXT-4 terminal (pages 36, 50)

8 Aerial socket (page 5)

DIGITAL AUDIO IN terminal (pages 36, 52)

Connecting the power cord to

the AC outlet

Initial settings

When the TV is first turned on, it goes into

the initial setting mode, and you will see the

JVC logo. Follow the instructions on the

screen display to make the initial settings.

Caution

• Operate only from the power source

specified (AC 220 – 240 V, 50 Hz) on the

unit.

Yellow button

Blue button

Putting the batteries into the

Remote control

1 Press the Main power button on the

Use two AAA/R03 dry cell batteries.

Insert the batteries from the - end, making

sure the + and - polarities are correct.

The Power lamp lights red (for power on),

then green (for TV on) and the JVC logo

appears.

Power lamp

Main power

button

• Follow the warnings printed on the

batteries.

• Battery life is about six months to one

year, depending on how much you use the

remote control.

• The batteries we supply are only for

setting up and testing your TV, please

replace them as soon as you need to.

• If the remote control does not work

properly, replace the batteries.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up your TV

• If the power lamp stays red and does not

change to green:

your TV is in the standby mode. Press the

# (standby) button on the remote

control to turn your TV on.

• If the JVC logo does not appear this is

because your TV has already been turned

on for the first time:

use the “LANGUAGE” and “AUTO

PROGRAM” functions to make the initial

settings. For details, see “INSTALL” on

page 41.

5 Press the blue button to start the

AUTO PROGRAM function

The AUTO PROGRAM menu appears

and received TV channels are

automatically stored in the programme

numbers (PR).

• To cancel the AUTO PROGRAM

function:

Press the b button.

2 Press the a button

The LANGUAGE menu appears.

After the TV channels have been

registered in the programme

numbers (PR), the EDIT menu

appears

• If you want to, you can now edit the

programme numbers (PR) using the

EDIT/MANUAL function. For details,

see “EDIT/MANUAL” on page 42.

• If you do not want to edit programme

numbers (PR), go to the next step.

3 Press the 6 buttons to choose

ENGLISH. Then press the a

button

The on-screen display will then be in

English.

If “ACI START/ACI SKIP” appears

in the AUTO PROGRAM menu:

You can use the ACI (Automatic Channel

Installation) function to decode the ACI

data and complete the registration of all

the TV channels quickly. For details of

the ACI function and how to use it, see

“Using the ACI function” on page 47.

If you don’t want to use the ACI function,

press the 6 buttons to choose ACI

SKIP and then press a.

The COUNTRY menu appears as a sub-

menu of the AUTO PROGRAM function.

There are two COUNTRY menus.

Pressing the yellow button changes the

COUNTRY menu as follows:

4 Press the 5 and 6 buttons to

choose the country where you are

• To receive SKY 1 you need a satellite

tuner. You must have the satellite tuner

set to SKY 1 before starting the AUTO

PROGRAM function which follows.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up your TV

• The AUTO PROGRAM function does not

set the programme number PR 0 (AV) for

your video cassette recorder. You will

need to set this using the MANUAL

function.

6 Press the a button to display the

T-V LINK menu

• In some areas you may get TV reception

from more than one transmitter, for

example different ITV regions. In this

case each TV channel could be set twice.

If this happens, the first set of channels

will have the stronger signal. If you want

to delete the second set of channels, you

will have to do it manually (see page 45).

7 If you do not have a T-V LINK

compatible VCR connected:

Press the b button to exit the T-V LINK

menu.

The T-V LINK menu disappears.

If you have a T-V LINK compatible

VCR connected to the EXT-2

terminal:

Follow the operating procedure “Using

the DECODER (EXT-2) function” on

page 48 to transmit the programme

number (PR) data.

Now, the initial settings are complete,

and you can watch the TV

• When the COUNTRY setting is

UNITED KINGDOM:

T-V LINK functions

When you have a T-V LINK compatible

VCR connected to the EXT-2 Terminal on

the TV, it is easier to set up the VCR and to

view videos. T-V LINK uses the following

features:

BBC1, BBC2, ITV, Channel 4 and

Channel 5 are automatically set to the

programme numbers PR1 to PR5. If the

TV doesn't receive one of these TV

channels, that programme number (PR)

will not be set. Programme number PR6 is

not normally set.

To use T-V LINK functions:

A “T-V LINK compatible VCR” means a

JVC video cassette recorder with the T-V

LINK logo, or with one of the following

logos. However, these VCRs may support

some or all of the features described earlier.

For details, see your VCR instruction

manual.

• When the COUNTRY setting is

IRELAND:

If your TV can detect the TV channel

name from the TV channel broadcast

signal, the TV channel name is assigned

to the programme number (PR) to which

the TV channel has been set. However,

which TV channels are set to which

programme numbers (PR) will depend on

the area in which you live.

• If a TV channel you want to view is not

set to a programme number (PR), you can

set it using the MANUAL function. For

details, see “EDIT/MANUAL” on

page 42.

“Q-LINK” (a trademark of Panasonic

Corporation)

“Data Logic” (a trademark of Metz

Corporation)

“Easy Link” (a trademark of Phillips

Corporation)

“Megalogic” (a trademark of Grundig

Corporation)

“SMARTLINK” (a trademark of Sony

Corporation).

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up your TV

You cannot carry out Direct Rec using your

TV’s control.

„ Pre-set download

The VCR will automatically download the

registered data on the TV channels from the

TV. This means you do not need to set up the

program channels on your VCR manually.

The preset download function automatically

begins when the initial setting is complete or

whenever you carry out the AUTO

Generally, the VCR cannot record a TV

channel that it cannot receive properly on its

own tuner, even if you can view that TV

channel on the TV. However, some VCRs

can record a TV channel by using the TV’s

output if that channel can be viewed on the

TV. For details, see your VCR instruction

manual.

PROGRAM or EDIT/MANUAL functions.

You can also carry out this function using

your VCR controls.

„ TV auto power on/VCR image view

When the VCR starts playing, the TV

When “FEATURE NOT AVAILABLE” is

displayed:

If “FEATURE NOT AVAILABLE” is

displayed, the download was not performed

correctly. Before trying to download again,

check that:

automatically turns on and the images from

the EXT-2 terminal appear on the screen.

When the VCR menu is operated, the TV

automatically turns on and the images from

the EXT-2 terminal appear on the screen.

• the VCR power is turned on

• the VCR is T-V LINK compatible

• the VCR is connected to the EXT-2

terminal

• This function does not happen if your

TV’s main power is turned off. Set your

TV’s main power to on (standby mode).

• the SCART cable is fully wired.

„ Direct Rec

“What You See Is What You Record”

You can easily record to VCR the images

that you are watching on the TV.

For details, read the manual for your VCR.

Use your VCR controls. “VCR IS

RECORDING” is displayed.

In the following situations, the VCR

will stop recording if the TV is turned

off, if the TV channel or input is

changed, or if the menu is displayed

on the TV:

• when recording images from an external

device connected to the TV (for example

a camcorder)

• when recording a TV channel after it has

been unscrambled on a decoder

• when recording a TV channel by using the

TV’s output because the VCR’s own

tuner cannot properly receive that

channel.

When the VCR is not ready (for example

when there is no tape inserted), “NO

RECORDING” is displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

TV buttons and functions

Turn the main power on

Press the Main power button on the

TV.

The power lamp lights red and your TV is in

the standby mode.

• If the power lamp lights green, the TV is

already on.

To turn the main power off:

Press the main power button again.

The power lamp goes off.

Caution

• The main power button on the TV does

not fully isolate the TV from the AC

supply. If you are not going to use the TV

for a long period of time, be sure to

disconnect the AC plug from the AC

socket.

Turn the TV on from standby

mode

Press the P p buttons to turn the TV

on from standby mode

Choose a TV channel

Press the P p buttons to choose a

programme number (PR) or an EXT

terminal

Refer to the pages in brackets for details.

1 Remote control sensor

2 Power lamp (6, 10)

3 Main power button (6, 10)

4 Headphone jack (mini jack) (50)

5 P p buttons/ q buttons (11)

6 r (Volume) button (10)

7 EXT-5 terminal (36, 50)

Adjust the volume

1 Press the r (Volume) button

The volume level indicator appears.

2 Press the q buttons while the

volume level indicator is on screen

• The headphone volume is adjusted

with the “HEADPHONE” menu (see

page 28).

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control buttons and functions

1 Muting button

2 Number buttons

3 c button

4 3 sound button

5 Information button

6 b button

7 5 buttons

8 Standby button

9 Colour buttons

0 a button

- 6 buttons

= VCR/DVD/Teletext control button

~ VCR P DVD switch

! g (Text) button

@ P button

# F button

$ U p button

% S button

^ MULTI button

Turn the TV on or off from

standby mode

Press the # (standby) button to turn

the TV on or off.

When the TV is turned on, the power lamp

changes from red to green.

• The power can be turned on by pressing

the b button, 6 buttons or Number

buttons.

Choose a TV channel

„ Use the number buttons:

Enter the programme number (PR)

of the channel using the number

buttons.

Example:

• PR6 → press 6

• PR12 → press 1 and 2

„ Use the 6 buttons:

Press the 6 buttons to choose

the programme number (PR) you

want.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control buttons and functions

„ Use the PR LIST:

Adjust the volume

1 Press the

(Information) button to

Press the 5 buttons to adjust the

volume.

The volume indicator appears and the

volume changes as you press the q

buttons.

display the PR LIST

Pressing the (information) button

changes the display as follows:

• The headphone volume is adjusted

with the “HEADPHONE” menu (see

page 28).

„ Muting the sound

No display

Press the (muting) button to

turn off the sound.

Pressing the (muting) button again

restores the previous volume level.

2 Press the 5 and 6 buttons to

choose a programme number (PR).

Then press the a button

Watch images from external

equipment

• For programme numbers (PR) with the

CHILD LOCK function set, the n

(CHILD LOCK) mark appears next to

the Programme number (PR) in the PR

LIST.

• You cannot use the 6 buttons to

choose a programme number (PR)

with the CHILD LOCK set.

„ Use the o button:

Press the o button to choose

an EXT terminal.

TV mode

EXT modes

Programme

numbers

PR 1 – PR 99

• Even if you try to choose a programme

number (PR) with the CHILD LOCK

set, the n (CHILD LOCK) mark will

appear, and you cannot watch the TV

channel. To watch the TV channel, see

“CHILD LOCK” on page 39.

• If the picture is tilted or unnatural

colour appears in the corner of the

screen, this can be corrected. See

“PICTURE TILT” on page 26.

„ Use the 6 buttons:

Press the 6 buttons to choose

an EXT terminal.

„ Use the PR LIST:

1 Press the

(Information) button to

display the PR LIST

2 Press the 5 and 6 buttons to

choose an EXT terminal. Then

press the a button

• The EXT terminals are registered after

the Programme number PR 99.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control buttons and functions

• You can choose a video input signal

from the S-VIDEO signal (Y/C signal)

and regular video signal (composite

signal). For details, see “S-IN (S-

VIDEO input)” on page 36.

• If you do not have a clear picture or no

colour appears, change the colour

system manually. See “COLOUR

SYSTEM” on page 25.

• If you choose an EXT terminal with no

input signal, the EXT terminal number

becomes fixed on the screen.

• This TV set has a function which can

automatically change over the input

according to a special signal output

from an external device. (The EXT-4

and EXT-5 terminals do not support

this function.)

ZOOM function

You can change the screen size according to

the picture aspect ratio. Choose the optimum

one from the following ZOOM modes.

AUTO:

When a WSS (Wide Screen Signalling)

signal, which shows the aspect ratio of the

picture, is included in the broadcast signal or

the signal from an external device, the TV

automatically changes the ZOOM mode to

16:9 ZOOM mode or FULL mode according

to the WSS signal.

If a WSS signal is not included, the picture is

displayed in accordance with the ZOOM

mode set with the 4:3 AUTO ASPECT

function.

• For details of the 4:3 AUTO ASPECT

function, see “4:3 AUTO ASPECT” on

page 26.

• When the AUTO (WSS) mode does not

function correctly due to poor WSS signal

quality or when you want to change the

ZOOM mode, press the c button

and change to another ZOOM mode.

To return to a TV channel:

Press the b button, the 6 buttons or the

number buttons.

To use the programme number PR 0

(AV):

When the TV and VCR are connected only

by the aerial cable, choosing the programme

number PR 0 (AV) allows you to view

images from the VCR. Set the VCR RF

channel to the programme number PR 0

(AV) manually. For details, see “EDIT/

MANUAL” on page 42.

REGULAR:

Use to view a normal picture (4:3 aspect

ratio) as this is its original shape.

Pressing the o button changes the

choice as follows:

PANORAMIC:

EXT modes

TV mode

This stretches the left and right sides of a

normal picture (4:3 aspect ratio) to fill the

screen, without making the picture appear

unnatural.

Programme

numbers

PR 1 – PR 99

• The top and bottom of the picture are

slightly cut off.

14:9 ZOOM:

This zooms up the wide picture (14:9 aspect

ratio) to the upper and lower limits of the

screen.

• The VCR sends its playback image along

the aerial cable as an RF (radio frequency)

signal.

• Also see your VCR instruction manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control buttons and functions

16:9 ZOOM:

This zooms up the wide picture (16:9 aspect

ratio) to the full screen.

„ Adjusting the visible area of the

picture

If subtitles or the top (or bottom) of the

picture are cut off, you can adjust the visible

area of the picture manually.

1 Press the c button

16:9 ZOOM SUBTITLE:

This zooms up the wide picture (16:9 aspect

ratio) with subtitles to the full screen.

The ZOOM menu appears.

2 Press the a button to display the

ZOOM mode indicator

The indicator appears.

FULL:

This uniformly stretches the left and right

sides of a normal picture (4:3 aspect ratio) to

fill the wide TV screen.

3 While it is displayed, press the 6

buttons to change the position of

the picture

• You cannot adjust the visible area in

REGULAR or FULL mode.

• For 16:9 aspect ratio pictures that have

been squeezed into a normal picture (4:3

aspect ratio), use the FULL mode to

restore the picture to its original shape.

„ Choose the ZOOM mode

1 Press the c button to display

the ZOOM menu

2 Press the 6 buttons to choose a

ZOOM mode. Then press the a

button

The picture expands and the chosen

ZOOM mode is displayed in about 5

seconds.

• The ZOOM mode may be

automatically changed by the control

signal from an external device. When

you want to return to the previous

ZOOM mode, choose the ZOOM

mode again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control buttons and functions

• This TV uses teletext data to set the time.

If the TV has not received a TV channel

that has teletext programmes since it was

turned on, the time display is blank. To

see the time, choose a TV channel that has

teletext programmes. The time will still

be displayed as long as you do not turn off

the TV, even if you choose other TV

channels.

3D-PHONIC function

Dolby Surround Pro Logic surround sound and

Dolby Digital surround sound can be easily

enjoyed without additional surround speakers.

You can turn the 3D-PHONIC function on or

off by one-touch operation.

Press the 3 button

Pressing the 3 button changes the function

as follows:

• When watching videos, an incorrect time

is sometimes displayed.

3D-PHONIC

Return to TV channel instantly

You can return to a TV channel instantly.

SURROUND OFF

Press the b button

The TV returns to the TV mode and a TV

channel appears.

• The 3 button does not work while the

headphones are connected to the TV.

• The 3D-PHONIC function can be also

turned on or off by using the

SURROUND FEATURES menu. For

details, see “3D-PHONIC” on page 29.

• As well as 3D-PHONIC, this TV has

“DOLBY SURROUND”, “DANCE

CLUB”, “CONCERT HALL” and

“STADIUM” surround modes. These

surround modes can be selected from the

SURROUND FEATURES menu. For

details, see “SURROUND FEATURES”

on page 29.

Using the FREEZE function

You can view the current programme as a

still picture.

1 Press the F button

The still picture of the current picture will

appear.

current

programme

still picture

D0056-EN

Displaying the current time

To cancel the FREEZE function:

Press the F button, the 6

buttons or the number buttons.

You can display the current time on the

screen.

Press the

display the current time

Pressing the (Information) button changes

(Information) button to

• The FREEZE function does not work

while a sub-picture is displayed.

• The still picture cannot be output from

the TV.

the display as follows:

No indication

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control buttons and functions

Listening to the sound of the sub-

picture:

You can listen to the sound of the sub-

picture with the headphones while

listening to the sound of the main-picture

from the TV speakers.

For details, see “HEADPHONE” on

page 28.

• The sub-picture sound is mono.

Using the PIP (picture-in-

picture) function

You can view two pictures (main-picture and

sub-picture).

Two different TV programmes can be

watched at the same time, or a TV

programme and a video programme from an

external device can be watched at the same

time.

Changing the position of the sub-

picture:

1 Press the P button

Pressing the P button changes the PIP

mode as follows:

You can choose one of four positions.

For details, see “PIP POSITION:” on

page 26.

Swapping the main-picture and

sub-picture:

Twin pictures mode

Press the S button.

The main-picture and sub-picture will be

swapped.

Main-

picture

Sub-

picture

Picture in picture mode

Sub-

picture

Main-

picture

D0051-EN

Cancelling the PIP function:

Press the P button or b button.

Cancel the PIP function

Main-

picture

• If the main-picture signal is poor, the

quality of the sub-picture may also be

poor.

D0057-EN

• If the pictures have different standards,

the top and bottom of one of them may

be missing.

• If an external device is operated, the

sub-picture may disappear. If this

happens, press the P button again to

redisplay the sub-picture.

2 Press the U p buttons to

change the sub-picture to the

picture from another TV channel or

another EXT terminal

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control buttons and functions

• You cannot view a scrambled channel

in the sub-picture. If the S button

is pressed when viewing a scrambled

channel in the main-picture using an

external decoder, the channel you have

been viewing in the sub-picture will

appear in both the main-picture and

sub-picture.

12-pictures multi:

Still

pictures

Moving

picture

D0058-EN

4-pictures multi:

• The ZOOM function does not work in

twin-picture mode.

Still

pictures

• Do not press the S button while

you are recording the TV output on the

VCR. If you do, the TV output signal

will change.

• The BLUE BACK function does not

work in twin picture mode or the

picture-in-picture mode.

• A progressive-scanning picture cannot

be displayed as the sub-picture.

Also:

- When the EXT-4 picture is a

progressive-scanning picture, you

cannot choose EXT-4 with the

U p buttons.

Main picture

Moving

picture

D0059-EN

• To display the next multi-pictures,

press the MULTI button.

2 Press the U p buttons to

choose the screen you want to see

The chosen picture changes to a moving

picture.

3 Press the a button

The multi-pictures disappear and the

chosen picture appears.

- When the EXT-4 picture signal is

changed to a progressive-scanning

picture while the EXT-4 picture is

displayed as the sub-picture, the PIP

function is cancelled.

Changing the multi-picture mode:

See “MULTI-PICTURE:” on page 26.

- The pictures cannot be swapped

when a progressive-scanning picture

from EXT-4 is being displayed as

the main picture.

Cancelling the multi-pictures:

Press the b button, the 6 buttons, the

number buttons or the a button.

• The sub-picture cannot be output from

the TV.

• Pictures from external devices cannot

be displayed in the 12-pictures multi

mode.

• In the 4-pictures multi mode, the

picture from external devices can only

be displayed as the main picture.

Using the MULTI-PICTURE

function

You can display multi-pictures so you can

find a program you want to view.

1 Press the MULTI button to display

multi-pictures

The channels are displayed in the channel

number order.

The multi-pictures will appear in one of

the two multi-picture modes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control buttons and functions

Operating a JVC brand VCR or

DVD player

These buttons will operate a JVC brand VCR

or DVD player. Pressing a button that looks

the same as the device’s original remote

control button has the same effect as the

original remote control.

1 Set the VCR P DVD switch to the

VCR or DVD position

VCR:

When you are using a VCR, set the switch

to the VCR position.

DVD:

When you are using a DVD player, set the

switch to the DVD position.

P (Text):

When you are viewing Teletext

programmes, set the switch to the

P (Text) position.

2 Press the VCR/DVD control button

to control your VCR or DVD player

• If your device is not made by JVC,

these buttons will not work.

• Even if your device is made by JVC,

some of these buttons may not work,

depending on the device you are using.

• You can use the p buttons to choose

a TV channel the VCR will receive, or

choose the chapter the DVD player

plays back.

• Some models of DVD player use the

p buttons for both operating the fast

forward/backward functions and for

choosing the chapter. In this case, the

253 buttons do not work.

Download from Www.Somanuals.com. All Manuals Search And Download.

Teletext function

4 Choose a teletext page by pressing

the 6 buttons, number buttons or

colour buttons

To return to the TV mode:

Press the b button or g (Text) button.

• If you have trouble receiving teletext

broadcasts, consult your local dealer or

the teletext station.

• The ZOOM function will not work in

the TV and text mode or Text mode.

• You cannot operate menus when

viewing a teletext programme.

• Language display depends on the

country which was set on the

COUNTRY menu. If characters on a

Teletext programme do not appear

properly, change the COUNTRY

Setting to another country. For detail,

“Using the DECODER (EXT-2)

function” on page 48.

Basic operation

You can view three types of teletext

broadcasts on the TV:

FLOF (Fastext), TOP and WST.

• TOP is not available when the

COUNTRY setting is UNITED

KINGDOM.

1 Choose a TV channel with a teletext

broadcast

Using the List Mode

You can store the numbers of your favourite

teletext pages in memory and call them up

quickly using the colour buttons.

2 Set the VCR P DVD switch to the

(Text) position

To store the page numbers:

1 Press the M button to go into

the List mode

3 Press g (Text) button to display

the teletext

The page numbers you have stored are

displayed at the bottom of the screen.

Pressing g (Text) button changes the

mode as follows:

2 Press a colour button to choose a

position. Then press the number

buttons to enter the page number

TV mode

TV and text mode

Text mode

Download from Www.Somanuals.com. All Manuals Search And Download.

Teletext function

3 Press and hold down the P

button

1 Press the O button to

operate the sub-page function

Sub-page numbers are displayed at the

left of the screen.

The four page numbers blink white to

show that they are stored in memory.

Colour*

Meaning of sub-page

number

To call up a stored page:

1 Press the M button to enter

the List mode

Yellow

Currently being

displayed.

The page stored with the red button

White

Can be displayed.

(

) is displayed.

Blue or Red

Cannot be displayed and

it is not sent.

2 Press a colour button having a

stored page

*: Background colour of the sub-page

number.

2 Press the 6 buttons to choose a

sub-page number

To leave the List mode:

Press the M button again.

To cancel the sub-page function:

Press the O button again.

Hold

Reveal

You can hold a teletext page on the screen for

as long as you want, even while several other

teletext pages are being received.

Some teletext pages include hidden text

(such as the answers to a quiz).

You can display the hidden text.

Press the N button

Each time you press the Q

button, text is hidden or revealed

Hold indication

To cancel the Hold function:

Press the N button again.

Sub-page

Some teletext pages include sub-pages that

are automatically displayed.

You can hold any sub-page, or view it at any

time.

Download from Www.Somanuals.com. All Manuals Search And Download.

Teletext function

Size

You can double the height of the teletext display.

Press the R button

Index

You can return to the index page instantly.

Press the T button

Returns to page 100 or a previously specified

page.

Cancel

You can search for a teletext page while

watching TV.

1 Press the number button to enter a

page number, or press a colour

button

The TV searches for a teletext page.

2 Press the S button

The TV programme appears. When the TV

finds the teletext page, its page number

appears in the upper left of the screen.

3 Press the S button to return

to a teletext page when the page

number is on the screen

• The TV mode cannot be resumed by

pressing the S button. To

return to the TV mode press b.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

This TV has a number of functions you can

operate using menus. To use all your TV’s

functions, you need to understand the basic

menu operating techniques fully.

2 Press the 6 buttons to choose a

menu title, and press the a button

The menu appears.

To return to the previous menu:

Press the

(information) button.

To exit a menu instantly:

Press the b button.

3 Press the 6 buttons to choose a

function

• For details of the functions in the

menus, see the following pages.

4 Press the 5 buttons to choose

the setting of that function

Basic operation

• If you want to operate a function

which appears only with its name,

follow the descriptions of that function

on the following pages.

1 Press the a button to display the

MENU (main menu)

• The display appearing at the bottom of

a menu shows you the button on the

remote control that you can use when

you operate a chosen function.

5 Press the a button to complete

the setting

• Press the a button twice while

watching the MULTI-PICTURE

mode.

• “SURROUND FEATURES” may not

be displayed in the MENU (main

menu) when the headphones are

connected.

The menu disappears.

• When watching the television with the

NTSC system, the menus are displayed

at about half of their normal vertical

size.

• The display appearing at the bottom of

a menu shows the buttons on the

remote control you can use when you

operate a chosen function.

The menu will disappear after about one

minute if no operation is performed.

(information)

BACK

button

b button

a button

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

HUE

PICTURE SETTING

You can adjust the picture tint.

2 : reddish

3 : greenish

• You can change the HUE setting (picture

hue) when the colour system is NTSC

3.58, NTSC 4.43 or a signal from the

EXT-4 terminal.

However, you cannot do this when the

PIP function main picture is set to EXT-4.

To return to the default settings in

each PICTURE MODE mode:

Press the blue button.

• This returns the picture settings in the

PICTURE MODE mode you have chosen

to the default settings, and stores them in

the PICTURE MODE mode.

„ PICTURE MODE

You can choose one of three PICTURE

MODEs to adjust the picture settings

automatically.

BRIGHT:

Heightens contrast and sharpness.

„ COLOUR TEMP.

STANDARD:

You can select one of three COLOUR

TEMP. modes (three tones of white) to adjust

the white balance of the picture. Since white

is the colour which is used as a reference for

all the other colours, changing the COLOUR

TEMP. mode affects the appearance of all

the other colours on the screen.

Standardizes picture adjustment.

SOFT:

Softens contrast and sharpness.

„ Picture Adjustment

You can change the picture settings of each

PICTURE MODE mode as you like.

COOL:

CONTRAST

A bluish white. Using this mode when

watching bright pictures allows you to enjoy

a more vivid and bright picture.

You can adjust the picture contrast.

2 : lower

3 : higher

NORMAL:

The normal white colour.

BRIGHT

You can adjust the picture brightness.

2 : darker

3 : brighter

WARM:

A reddish white. Using this mode when

watching films allows you to enjoy colours

that are characteristic of films.

SHARP

You can adjust the picture sharpness.

2 : softer

3 : sharper

COLOUR

You can adjust the picture colour.

2 : lighter

3 : deeper

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

PICTURE FEATURES

• When a progressive-scanning picture is

being displayed, “DIGITAL VNR”

cannot be selected.

• The DIGITAL VNR function does not

work for progressive-scanning pictures.

„ Super DigiPure

The Super DigiPure function uses the latest

in digital technology to give you a natural-

looking picture. The Super DigiPure function

includes the following two functions.

„ DIGITAL VNR

The DIGITAL VNR function cuts down the

amount of ‘noise’ (‘snow’ or interference) in

the original picture.

DigiPure function:

This function helps to create a natural-looking

picture by eliminating unnecessary edges

from high-contrast and crisp images. For

images with low-contrast, edges are added to

produce a sharper, more detailed picture.

You can choose from the three DigiPure

function settings of AUTO, MIN and MAX.

• If you set the DigiPure effect too high on

a low-quality picture that contains a lot of

noise, this may actually make the noise

worse. We recommend you use the

AUTO setting if you can.

You can choose from the three DIGITAL

VNR function settings of AUTO, MIN and

MAX.

AUTO:

The TV will automatically adjust the level of

the DIGITAL VNR effect to match the

amount of noise in the picture, giving you the

best possible picture.

• If you set the DIGITAL VNR effect too

high it can make the picture less sharp. It

is recommended to use the AUTO setting

if you can.

Picture motion compensation

function:

This function displays fast-moving pictures

(for example, the players or ball in a football

game) more smoothly and naturally on the

screen.

• The effect level of the picture motion

compensation function cannot be

changed. The effect level is the same no

matter which of the AUTO, MIN or MAX

settings is used.

• AUTO cannot be chosen when you are

watching the EXT-4 picture.

MIN:

The level of the DIGITAL VNR effect is set

to the minimum. If you set the DIGITAL

VNR function to AUTO but feel that the

sharpness of the original picture has not been

reproduced fully, change the setting from

AUTO to MIN.

• The MIN setting is not suitable for low-

quality pictures which contain a lot of

noise.

1 Choose Super DigiPure

2 Press the 5 buttons to choose a

setting. Then press the a button

MAX:

The level of the DIGITAL VNR effect is set

to the maximum. If you set the DIGITAL

VNR function to AUTO but still notice some

noise, change the setting from AUTO to

MAX.

• The MAX setting is not suitable for high-

quality pictures which contain very little

noise.

AUTO:

The TV will automatically adjust the level of

the DigiPure effect to match the amount of

noise in the picture, giving the best possible

picture.

• AUTO cannot be chosen when you are

watching the EXT-4 picture.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

MIN:

PAL:

PAL system

SECAM:

SECAM system

NTSC 3.58:

NTSC 3.58 MHz system

NTSC 4.43:

NTSC 4.43 MHz system

The level of DigiPure effect is set to the

minimum. When you set the Super DigiPure

function to AUTO and notice some noise,

change the setting from AUTO to MIN.

• The MIN setting is not suitable for high-

quality pictures which contain very little

noise.

MAX:

AUTO:

The level of DigiPure effect is set to the

maximum. If you set the Super DigiPure

function to AUTO but feel that the original

picture quality has not been reproduced fully,

change the setting from AUTO to MAX.

• The MAX setting is not suitable for low-

quality pictures which contain a lot of

noise.

This function detects a colour system

from the input signal. You can only use

this when you are viewing a picture from

programme number PR 0 (AV), or an

EXT terminal.

• The AUTO function may not function

properly if you have poor signal quality.

If the picture is abnormal in the AUTO

function, choose another colour system

manually.

• When in the Programme numbers PR 0

(AV) to PR 99, you cannot choose NTSC

3.58 or NTSC 4.43.

OFF:

The Super DigiPure function is turned off.

„ COLOUR SYSTEM

The colour system is chosen automatically.

However, if the picture is not clear or no

colour appears, choose the colour system

manually.

SECAM cannot be chosen when the

COUNTRY setting is UNITED

KINGDOM.

1 Choose COLOUR SYSTEM. Then

press the a button

The sub-menu of the COLOUR SYSTEM

function appears.

„ MOVIE THEATRE

The MOVIE THEATRE function displays a

cinema film picture more smoothly and

naturally on the screen.

COLOUR SYSTEM

MAIN

SUB

AUTO:

PAL

AUTO

The television automatically recognizes the

type of signal and turns the function on and

off.

BACK

ON:

D0016-EN

This function is turned on.

2 Press the 5 buttons to choose

OFF:

MAIN or SUB

MAIN:

This function is turned off.

You can change the colour system of the

main-picture.

SUB:

You can change the colour system of the

sub-picture.

• Choose MAIN when a sub-picture is

not displayed.

• The motion may appear unnatural when

viewing images with the NTSC colour

system. When the MOVIE THEATRE

function is set to AUTO or ON, the

motion may appear unnatural when

viewing images with the NTSC colour

system.

• You cannot select this function in the twin

pictures mode or the picture-in-picture

mode.

3 Press the 6 buttons to choose

the appropriate colour system.

Then press the a button

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

„ 4:3 AUTO ASPECT

„ PIP (picture-in-picture)

You can choose one of three ZOOM modes,

REGULAR, PANORAMIC or 14:9 ZOOM,

as the ZOOM mode for the normal picture

(4:3 aspect ratio).

PIP POSITION:

You can choose one of four positions for the

sub-picture.

1 Press the 6 buttons to choose

PIP. Then press the a button

The PIP menu appears.

1 Choose 4:3 AUTO ASPECT then

press the a button

2 Press the 6 buttons to choose a

D0061-EN

ZOOM mode

2 Press the 6 buttons to choose

„ PICTURE TILT

PIP POSITION

There are cases where the Earth’s magnetic

force may make the picture tilt or make

unnatural colours appear in the corner of the

screen. If this happens, you can correct it.

3 Press the 5 buttons to choose

the position. Then press the a

button

1 Choose PICTURE TILT. Then press

MULTI-PICTURE:

Choosing the number of pictures for the

the a button

MULTI-PICTURE function

1 Press the 6 buttons to choose

PIP. Then press the a button

The PIP menu appears.

2 Press the 6 buttons to choose

MULTI-PICTURE

2 Press the 6 buttons until the

picture becomes level

To reduce unnatural colouring:

1 Press the blue button in order to

display the purity correction

screen

D0062-EN

3 Press the 5 buttons and choose

the number of pictures. Then press

the a button

2 Press the 5 buttons until the

unnatural colouring is reduced

as much as possible

3 Press the a button

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

BALANCE

You can adjust the volume balance between

the left and right speaker.

SOUND SETTING

2 : turn the left speaker’s volume level up.

3 : turn the right speaker’s volume level up.

„ SPEAKER

You can turn off the sound from the TV

speakers; but you should only do this if you

have connected an audio system to the TV

instead of the TV speakers.

ON:

The TV speakers issue sound.

• “BALANCE”, “SPEAKER” and

“SUBWOOFER” are not displayed when

using the 3D-PHONIC function or

DOLBY SURROUND function.

OFF:

The TV speakers do not issue sound.

• The 5 buttons of the TV remote

control and the r (volume) buttons at

the front panel of your TV set can be used

to control the volume of each speaker

simultaneously.

• Setting the volume of the amplifier too

high may damage the front speakers.

• The 3D-PHONIC TV SPEAKER and

DOLBY SURROUND TV SPEAKER

settings in the SURROUND FEATURES

menu are changed when the SPEAKER

setting is changed.

„ STEREO / I • II

When you are viewing a bilingual broadcast

programme, you can choose the sound from

Bilingual I (Sub I) or Bilingual II (Sub II). If

you have poor reception on a stereo

broadcast, you can change from stereo to

mono sound so that you can hear the

broadcast more clearly and easily.

s: Stereo sound

v : mono sound

t : Bilingual I (sub I)

u : Bilingual II (sub II)

„ SUBWOOFER

• The sound mode you can choose differs

depending on the TV programme.

• This function does not work in the EXT

modes. And this function does not appear

in the SOUND SETTING menu.

You can choose the woofer to use.

INT.:

Choose to use the TV woofer for the bass

sound.

EXT.:

Choose when using an external subwoofer.

No sound comes from the TV woofer.

„ Sound Adjustment

You can adjust the sound to your liking.

OFF:

BASS

Choose when you do not want to emit any

sound to come from either the TV woofer or

external subwoofer.

You can adjust the low tone of the sound.

2 : weaker

3 : strong

TREBLE

• The 3D-PHONIC SUBWOOFER and

DOLBY SURROUND SUBWOOFER

settings in the SURROUND FEATURES

menu are changed when the

You can adjust the high tone of the sound.

2 : weaker

3 : strong

SUBWOOFER setting is changed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

SUB:

You can listen to the sound of the sub-

„ HEADPHONE

You need to use the HEADPHONE menu to

adjust the volume of the headphones.

The HEADPHONE menu can also be used to

set whether or not sound comes from the TV

speakers when the headphones are being

used and to perform the settings for the sound

coming from the headphones.

picture with your headphones.

• When the sub-picture is a television

programme, the sound becomes

mono.

3 Press the a button

• The surround function does not work for

the sound from the headphones. DOLBY

SURROUND sound becomes stereo

sound.

Hint:

When a sub-picture is displayed, the sound of

the sub-picture can be listened to with the

headphones while listening to the sound of

the main-picture with the TV speakers. To do

this, set TV SPEAKER to ON and OUTPUT

to SUB.

The surround function can be applied to the

sound from the TV speaker (external

speaker).

1 Press the 6 buttons to choose

HEADPHONE. Then press the a

button

The sub-menu of the HEADPHONE

function appears.

Using the “HEADPHONE” menu setting

when the sub-picture is displayed.

• When the headphones are connected

while the TV SPEAKER is ON and

OUTPUT is set to MAIN, the surround

function does not work for the sound from

the TV speaker (external speaker).

When DOLBY SURROUND sound is

used, the sound from the TV speaker

(external speaker) becomes stereo.

If the headphones are connected when the

sub-picture is not displayed.

D0044-EN

2 Press the 6 buttons to choose a

function. Then press the 5

buttons to change the setting

VOLUME:

You can change the volume of the

headphones.

• Sound comes from the headphones

irrespective of the OUTPUT setting.

• When the TV SPEAKER setting is ON,

the surround function does not work for

the sound from the TV speaker (external

speaker).

When DOLBY SURROUND sound is

used, the sound from the TV speaker

(external speaker) becomes stereo.

TV SPEAKER:

You can turn the TV’s speakers on or off.

ON:

The sound comes from the TV’s

speakers when using the headphones.

OFF:

The sound does not come from the

TV’s speakers when using the

headphones.

OUTPUT:

You can choose the sound output to the

headphones.

MAIN:

You can listen to the sound of the

main-picture with your headphones.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

When viewing a programme from the

EXT terminal which has not been set

to DIGITAL-IN, or when viewing a TV

programme:

SURROUND FEATURES

When viewing Dolby Surround encoded

programmes, you can enjoy the atmosphere

of Dolby Surround Pro Logic surround

sound.

• For details of how to adjust the surround

effect level, adjust the volume balance of

the speakers, and perform the setting

necessary when adding a front speaker

system or subwoofer system, see “3D-

PHONIC setting” on page 30.

• You can turn this function on or off with a

single press. For details, see “3D-

PHONIC function” on page 15.

• “SURROUND FEATURES” may not be

displayed in the MENU (main menu)

when the headphones are connected.

Disconnect the headphones before using

the “SURROUND FEATURES” menu.

„ 3D-PHONIC

„ DOLBY SURROUND

Dolby Surround Pro Logic surround sound

and Dolby Digital surround sound can be

easily enjoyed without additional surround

speakers.

You can enjoy the surround sound of Dolby

Digital programmes and Dolby Surround

encoded programmes.

• This function does not work properly

except for Dolby Surround encoded

programmes and Dolby Digital

Using rear surround signals of Dolby

Surround encoded programmes or Dolby

Digital programmes, this function will create

the surround sound as if surround speakers

were located to your right and left.

• This function does not work properly

except for Dolby Surround encoded

programmes and Dolby Digital

programmes.

• Additional surround speakers are needed

to use this function to enjoy surround

sound. Although you can listen to Dolby

Digital audio without surround speakers,

you cannot enjoy surround sound such as

5.1-channel Dolby Digital surround

sound. For details, see “DOLBY

SURROUND setting” on page 32.

• Before using this function, correctly set

each of the items in the DOLBY

DIGITAL/PRO LOGIC menu in

accordance with “DOLBY SURROUND

setting” on page 32.

When viewing a programme from the

EXT terminal which has been set to

DIGITAL-IN:

You can enjoy the atmosphere of the

surround sound of Dolby Digital

programmes.

If the programme source has 5.1-channel

Dolby Digital soundtracks, you can enjoy the

atmosphere of the 5.1- channel Dolby Digital

surround.

When viewing Dolby Surround encoded

programmes, you can enjoy the atmosphere

of Dolby Surround Pro Logic surround

sound.

When viewing a programme from the

EXT terminal which has been set to

DIGITAL-IN:

You can enjoy the surround sound of Dolby

Digital programmes.

If the programme source has 5.1-channel

Dolby Digital soundtracks, you can enjoy the

5.1-channel Dolby Digital surround sound.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

When viewing Dolby Surround encoded

programmes, you can enjoy Dolby Surround

Pro Logic surround sound.

• When Dolby Digital surround sound is

being used, “DOLBY DIGITAL” is

displayed at the top right of the screen for

a few seconds.

„ Other surround function

DANCE CLUB:

This function creates a dance club

atmosphere.

CONCERT HALL:

This function creates a concert hall

atmosphere.

When Pro Logic compatible Dolby

Digital surround sound is being used,

“DOLBY D+PL” is displayed at the top

right of the screen for a few seconds.

When digital sound (PCM) is being used,

“PRO LOGIC” is displayed at the top

right of the screen for a few seconds.

STADIUM:

This function creates a stadium atmosphere.

• The above function does not appear in the

SURROUND FEATURES menu when

viewing a programme from the EXT

terminal which has been set to

When viewing a programme from the

EXT terminal which has not been set

to DIGITAL-IN, or when viewing a TV

programme:

When viewing Dolby Surround encoded

programmes, you can enjoy Dolby Surround

Pro Logic surround sound.

DIGITAL-IN.

• The above function does not work

properly for Dolby Surround encoded

programmes or mono sound programmes.

3D-PHONIC setting

• When an EXT signal is being used, “PRO

LOGIC” is displayed at the top right of

the screen for a few seconds.

1 Press the 6 buttons to choose

3D-PHONIC. Then press the 3

button

• Dolby* Digital is an advanced form of

digital audio coding. Dolby Digital audio

is available from programme sources

(such as DVD-video discs) which are

usually identified with a Dolby Digital

logo.

* Manufactured under license from Dolby

Laboratories.

“Dolby”, “Pro Logic”, and the double-D

symbol are trademarks of Dolby

Laboratories.

2 Press the 6 buttons to choose an

item. Then press the 5 buttons

to change the setting

TV SPEAKER:

L/C/R:

Choose when using the TV speaker.

CENTRE:

Choose when using external front L/R

speakers and using the TV speaker as

the centre speaker.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

OFF:

Choose when using an external front

3 Press the a button to complete

the setting

speaker. Sound does not come from

the TV speaker.

The menu disappears.

„ Setting for using the TV speaker

• The DOLBY SURROUND TV

SPEAKER and SOUND SETTING

menu SPEAKER settings are changed

when the TV SPEAKER setting is

changed.

and woofer

SUBWOOFER:

INT.:

Choose to use the TV woofer for the

bass sound.

• Bass sound does not come from the

other speakers.

TV SPEAKER: L/C/R

SUBWOOFER: INT.

EXT.:

LEVEL: Adjust the volume.

VOLUME (LEFT/CENTRE/RIGHT/

SUBWOOFER): Adjust the balance of the

speakers.

Choose when using an external

subwoofer. No sound comes from the

TV woofer.

• Bass sound does not come from the

other speakers.

„ Setting for using an external front

speaker, and using the TV

speaker as the centre speaker and

woofer

OFF:

Choose when you do not want any

sound from either the TV woofer or

external subwoofer.

• The bass sound comes from the

front L/R speakers.

• The DOLBY SURROUND

SUBWOOFER and SOUND

SETTING menu SUBWOOFER

settings are changed when the

SUBWOOFER setting is changed.

TV SPEAKER: CENTRE

SUBWOOFER: INT.

LEVEL:

LEVEL: Adjust the volume.

VOLUME (LEFT/CENTRE/RIGHT/

SUBWOOFER): Adjust the balance of the

speakers.

You can control the effect level of the

3D-PHONIC function as you like.

VOLUME (LEFT/CENTRE/RIGHT/

SUBWOOFER):

You can adjust the sound level of each

speaker individually. LEFT/RIGHT

means left and right of the front speakers,

CENTRE means the centre speaker.

SUBWOOFER adjusts the volume of the

TV woofer and external subwoofer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

„ Setting for using an external front

speaker and subwoofer, and

using the TV speaker as the

centre speaker

DOLBY SURROUND setting

Correctly set the items in the sub-menu of the

DOLBY SURROUND function, and use the

test signal to control the volume level of the

speakers so that you can listen to the sounds

from them uniformly. Be sure to perform this

operation before using the DOLBY

DIGITAL/PRO LOGIC function.

1 Press the 6 buttons to choose

DOLBY SURROUND. Then press

the 3 button

The sub-menu of the DOLBY

SURROUND function appears.

TV SPEAKER: CENTRE

SUBWOOFER: EXT.

LEVEL: Adjust the volume.

VOLUME (LEFT/CENTRE/RIGHT/

SUBWOOFER): Adjust the balance of the

speakers.

Hint:

When only using an external front speaker

which is large enough for the bass sound, and

also emitting the bass sound from the front

speaker, set SUBWOOFER to OFF. If set to

anything else, the bass sound is not emitted

from the external front speaker.

Also, when using a front speaker and

subwoofer from the same amplifier, set the

SUBWOOFER to OFF.

2 Press the 6 buttons to choose an

item. Then press the 5 buttons

to change the setting

TV SPEAKER:

L/C/R:

Choose when using the TV speaker.

CENTRE:

Choose when using external front L/R

speakers and using the TV speaker as

the centre speaker.

OFF:

Choose when using an external front

speaker. Sound does not come from

the TV speaker.

• The 3D-PHONIC TV SPEAKER and

SOUND SETTING menu SPEAKER

settings are changed when the TV

SPEAKER setting is changed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

REAR SPEAKER:

DELAY TIME:

A delay can be applied to SURROUND

(surround sound) and CENTRE (centre

sound) depending on the arrangement of

the speakers.

Select DELAY TIME and press the 3

button to display the DELAY TIME

menu. The DELAY TIME is changed in

1/1000 second steps every time the 5

buttons are pressed.

ON:

Choose when surround speakers are

connected.

OFF:

Choose when surround speakers are

not connected.

SUBWOOFER:

INT.:

Choose to use the TV woofer for the

bass sound.

• Bass sound does not come from the

other speakers.

EXT.:

Choose when using an external

subwoofer. No sound comes from the

TV woofer.

• Bass sound does not come from the

other speakers.

• The CENTRE (centre sound) DELAY

TIME can only be adjusted when the

TV SPEAKER is set to CENTRE.

• The SURROUND (surround sound)

DELAY TIME can only be adjusted

when the REAR SPEAKER is set to

ON.

• The DELAY TIME menu is not

displayed when TV SPEAKER is set

to L/C/R or OFF and REAR

OFF:

Choose when you do not want any

sound from either the TV woofer or

external subwoofer.

• The bass sound comes from the

front L/R speakers.

SPEAKER is set to OFF.

• SUBWOOFER setting in the

3D-PHONIC SUBWOOFER and

SOUND SETTING menu are changed

when the SUBWOOFER setting is

changed.

3 Press the a button to complete

the setting

The menu disappears.

TEST MODE/VOLUME

(LEFT/CENTRE/RIGHT/LS/RS/

SUBWOOFER):

Set the volume balance of the speakers so

that the correct surround effect can be

achieved.

When the other settings have been

completed, adjust in accordance with

“Adjusting the volume balance with the

TEST MODE” on page 35.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

„ Setting for using surround

speakers connected to the TV

For details of how to connect and place the

surround speakers, see “Using additional

audio equipment” on page 52.

„ Settings for using an external

front speaker and subwoofer

surround speakers connected to

the TV

For details of how to connect and place the

surround speakers, external front speakers

and subwoofer, see “Using additional audio

equipment” on page 52.

TV SPEAKER: L/C/R

REAR SPEAKER: ON

SUBWOOFER: INT.

VOLUME (LEFT/CENTRE/RIGHT/LS/RS/

SUBWOOFER): Adjust the balance of the

speakers.

DELAY TIME: Adjust according to where

the speakers are placed.

TV SPEAKER: CENTRE

REAR SPEAKER: ON

SUBWOOFER: EXT.

VOLUME (LEFT/CENTRE/RIGHT/LS/RS/

SUBWOOFER): Adjust the balance of the

speakers.

DELAY TIME: Adjust according to where

the speakers are placed.

„

Settings for using an external front

speaker with surround speakers

connected to the TV

For details of how to connect and place the

surround speakers and external front

speakers, see “Using additional audio

equipment” on page 52.

Hint:

When only using an external front speaker

which is large enough for the bass sound, and

also emitting the bass sound from the front

speaker, set SUBWOOFER to OFF. If set to

anything else, the bass sound is not emitted

from the external front speaker.

Also, when using a front speaker and

subwoofer from the same amplifier, set the

SUBWOOFER to OFF.

TV SPEAKER: CENTRE

REAR SPEAKER: ON

SUBWOOFER: INT.

VOLUME (LEFT/CENTRE/RIGHT/LS/RS/

SUBWOOFER): Adjust the balance of the

speakers.

DELAY TIME: Adjust according to where

the speakers are placed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

LS/RS:

„ Adjusting the volume balance

with the TEST MODE

The left or right of the surround speakers.

If REAR SPEAKER is set to OFF, LS and

RS are not displayed.

Use the test signal to adjust the volume level

of each speaker so that they are all the same.

SUBWOOFER:

Preparation:

TV woofer or external subwoofer

• A test signal is not output from the

subwoofer in the TEST MODE. After

using the TEST MODE to adjust the

balance of the other speakers, stop the

test signal and adjust the volume of the

subwoofer while playing back some

actual sounds.

• The TV volume cannot be adjusted after

the menu is displayed. Increase the TV

volume level to about 10 before

displaying the menu.

1 Display the sub-menu of the

DOLBY DIGITAL/PRO LOGIC

function

2 Press the 6 buttons to choose

TEST MODE. Then press the 5

buttons to choose ON

4 Press the a button to complete

the settings

The menu disappears.

Test signals are output from each of the

speakers in turn.

• The subwoofer test signal is not output.

When using the front speaker system or

subwoofer system with the TV, it is

recommend that this TEST MODE is used

to adjust the speaker volume levels each

time the system is used.

When using the front speaker

system and/or subwoofer system

with the TV:

Turn on the power of each amplifier,

slowly increase the amplifiers’ volumes

until the sound from each speaker

connected to the system is about the same

as that of the sound from the TV speakers.

Note that increasing the amplifier volume

too high may damage the speakers.

Stopping the test signal:

Press the 6 buttons to choose TEST

MODE and press the 5 buttons to

choose OFF.

3 Press the 6 buttons to adjust the

sound volume of each of the

speakers

Adjust the sound volumes so that you can

listen to the sounds at the same volume

when you are sitting where you would

normally sit to watch the TV.

LEFT/RIGHT:

The left or right of the front speakers

CENTRE:

The centre speaker

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

EXT SETTING

• The EXT-1 terminal does not support

S-VIDEO signal (Y/C signal) and you

cannot set S-IN (S-VIDEO input) in

the EXT-1 terminal.

• Setting S-IN (S-VIDEO input)

changes the head character from “E” to

“S”. When an EXT terminal receives a

normal video signal, “E1”, “E2”, “E3”

or “E4” appears on the display. This

changes to “S2”, “S3” or “S5” when it

receives an S-VIDEO signal.

• Even a device which can output an

S-VIDEO signal (Y/C signal) may

output a regular video signal

(composite signal) depending on the

device setting. If a picture cannot

appear because the S-IN (S-VIDEO

input) setting has been made, read the

device instruction manual carefully

again to check for the device settings.

„ S-IN (S-VIDEO input)

You can connect a device (such as an S-VHS

VCR) to enjoy the high-quality picture of the

S-VIDEO signal (Y/C signal).

Preparation:

• First read the device’s instruction manual

and “Additional preparation” on page 50

to connect the device to the TV properly.

Second, follow the device’s instruction

manual to set the device so that it sends an

S-VIDEO signal (Y/C signal) to the TV.

• Do not set S-IN (S-VIDEO input) to an

EXT terminal connected to a device

which cannot output an S-VIDEO (Y/C

signal). If it is set wrongly, a picture

cannot appear.

„ DIGITAL-IN

When connecting a device (such as DVD

player) which enables Dolby Digital audio

signal to be output, you can listen to Dolby

Digital audio.

Preparation:

• To listen to Dolby Digital audio, correctly

connect a device to the TV in accordance

with “Listening to Dolby Digital audio”

on page 52.

1 Choose an EXT terminal

2 Press the yellow button and set the

S-IN (S-VIDEO input).

• If DIGITAL-IN is set by mistake when no

device is connected to the DIGITAL

AUDIO IN, no sound is emitted.

Then press the a button

An S-IN (S-VIDEO input) mark is

displayed. You can view an S-VIDEO

signal (Y/C signal) instead of the regular

video signal (composite signal).

1 Press the 6 buttons or 5

buttons to choose an EXT terminal

To cancel the S-IN (S-VIDEO input)

setting:

Press the yellow button and turn off S-IN

(S-VIDEO input) mark. The regular video

signal (composite signal) pictures are

resumed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

2 Press the green button to set the

DIGITAL-IN

3 Press the 6 buttons to choose a

name. Then press the a button

The ID LIST disappears and the name is

assigned to the EXT terminal.

Press the green button repeatedly until the

mark which is the same as the type of

cable connected to the DIGITAL AUDIO

IN terminal is selected.

• You cannot choose an EXT terminal

name that is not on the name list (ID

LIST).

: Select this mark when connected

with coaxial cable.

: Select this mark when connected

with optical cable.

To erase a name assigned to the

EXT terminal:

Choose a blank space.

To cancel the DIGITAL-IN setting:

Press the green button to turn off the mark

of DIGITAL-IN.

4 Press the a button to complete

the setting

3 Press the a button to complete

the setting

„ DUBBING

You can choose a signal source to be output

from the EXT-2 terminal.

The menu disappears.

• DIGITAL-IN cannot be set for the TV

terminal and EXT-5 terminal.

You can do this with the output signals of the

devices connected to other EXT terminals, or

with the picture and sound from a TV

channel you are currently viewing.

• This TV does not work with digital

audio signals other than Dolby Digital

audio. If no sound is emitted from the

speakers, cancel the DIGITAL-IN

setting and change to normal analogue

sounds.

1 Press the 5 buttons to choose

the arrow from the menu

„ LIST

You can store a name for each of the devices

connected to each EXT terminal. Giving a

name to an EXT terminal makes the EXT

terminal number appear on the screen,

together with its name.

1 Choose an EXT terminal

2 Press the 6 buttons to choose an

EXT terminal or TV.

2 Press the blue button to display the

name list (ID LIST)

Then press the a button

The arrow in the menu represents a signal

flow. The left side of the arrow shows a

signal source output from the EXT-2

terminal.

EXT-1/EXT-3/EXT-5:

The output signal of the device connected

to an EXT terminal passes through the TV

and is output from the EXT-2 terminal.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

TV:

FEATURES

The picture and sound of the TV channel

you are currently viewing are output from

the EXT-2 terminal.

• During dubbing, you cannot turn off

the TV. Turning off the TV also turns

off the output from the EXT-2

terminal.

• When you choose an EXT terminal as

an output, you can view a TV

programme or a picture from the other

EXT terminal while dubbing the

picture from a device connected to the

EXT terminal onto a VCR connected

to the EXT-2 terminal.

„ SLEEP TIMER

You can set the TV to automatically turn off

after a specified period of time.

1 Choose SLEEP TIMER, then press

the a button

• The RGB signals from TV games

cannot be output.Teletext programmes

cannot be output.

A Sub-menu of the SLEEP TIMER

function appears.

• The sound from the EXT terminal set

to DIGITAL-IN is not output from the

EXT-2 terminal.

2 Press the 5 buttons to set the

period of time.

Then press the a button

You can set the period of time up to a

maximum of 120 minutes (2 hours) in 10

minute steps.

• One minute before the SLEEP TIMER

function turns off the TV, “GOOD

NIGHT!” appears.

• The SLEEP TIMER function cannot

be used to turn off the TV’s main

power.

• When the SLEEP TIMER function is

on, you can display the sub-menu of

the SLEEP TIMER function again to

confirm or change the remaining

period of time of the SLEEP TIMER

function. Press the a button to leave

the menu after confirming or changing

the remaining time.

To cancel the SLEEP TIMER

function:

Press the 2 button to set a period of time

to “OFF”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

3 Press the a button

„ BLUE BACK

You can set the TV to automatically change

to a blue screen and mute the sound if the

signal is weak or absent, or when there is no

input from an external device.

The Sub-menu of CHILD LOCK appears.

ON:

This function is turned on.

OFF:

This function is turned off.

„ CHILD LOCK

When there is a TV channel you do not want

your children to watch, you can use the

CHILD LOCK function to lock out the TV

channel. Even when a child chooses a

programme number (PR) for a locked TV

channel the screen will change to blue and

display n (CHILD LOCK) so the TV channel

cannot be viewed. Unless you enter a pre-set

ID number by a special operation, the lock

cannot be released and the child cannot view

the TV channel.

4 Press the 6 buttons to choose a

TV channel

Every time you press the 6 buttons, the

Programme number (PR) changes, and the

picture of the TV channel registered in the

Programme number (PR) is displayed on

the screen.

5 Press the blue button and set the

CHILD LOCK function.

To set the CHILD LOCK function

Then press the a button

n (CHILD LOCK) appears and the TV

channel is locked.

1 Choose CHILD LOCK, then press

the o button

“SET ID NO.” (ID number setting screen)

appears.

To reset the CHILD LOCK function:

Press the blue button again.

n (CHILD LOCK) disappears.

To disable easy resetting of the CHILD

LOCK function, the menu disappears if

you choose the CHILD LOCK function

and press the a button.

2 Set the ID number to your liking

To view a locked TV channel

1 Press the 6 buttons to choose

a number.

1 Choose a programme number (PR)

of a locked TV channel with the

number buttons or PR LIST

The screen changes to blue and the n

(CHILD LOCK) appears. You cannot

view the TV channel.

2 Press the 5 buttons to move

the cursor.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

2 Press the (Information) button to

„ DECODER (EXT-2)

You can only use this function if you have a

decoder connected to a T-V LINK

compatible VCR, which in turn is connected

to the EXT-2 terminal. To use this function,

see “Using the DECODER (EXT-2)

function” on page 48.

display “ID NO.” (ID No. input

screen)

3 Press the number buttons to enter

the ID number

Caution

• If you have not connected a decoder with

a T-V LINK compatible VCR to the EXT-2

terminal, setting this function to “ON” by

mistake causes the picture/sound of a TV

channel you are currently viewing to

disappear.

The lock is temporarily released so you

can view the TV channel.

If you have forgotten the ID

number:

Perform step 1 of “To set the CHILD

LOCK function”. After confirming the ID

number, press the b button to exit the

menu.

• Even if you reset the lock temporarily,

it does not mean that the CHILD

LOCK function set for the TV channel

is cancelled. The next time anyone

tries to view the TV channel, it will be

locked again.

• When you want to cancel the CHILD

LOCK function, you must perform the

operation “To set the CHILD LOCK

function” again.

• To stop it being easy to choose the

programme number (PR) of a locked

TV channel, the programme number

(PR) has been set so that it cannot be

chosen with the 6 buttons or the

buttons of the TV.

• To stop it being easy to reset the lock,

“ID NO.” (ID No. input screen) is set

so that it cannot appear unless you

press the

(Information) button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

1 Choose AUTO PROGRAM. Then

press the a button

INSTALL

The COUNTRY menu appears as a sub-

menu of the AUTO PROGRAM function.

There are two COUNTRY menus.

Pressing the yellow button changes the

COUNTRY menu as follows:

„ LANGUAGE

You can choose the language you want to use

for the on-screen display from the language

list in a menu.

2 Press the 5 and 6 buttons to

1 Choose LANGUAGE, then press

the a button

choose the country where you are

A sub-menu of the LANGUAGE function

appears.

3 Press the a button to start the

AUTO PROGRAM function

The AUTO PROGRAM menu appears

and the TV channels you receive are

automatically registered in the

programme numbers (PR) list.

• To cancel the AUTO PROGRAM

function, press the b button.

2 Press the 5 and 6 buttons to

choose a language.

Then press the a button

„ AUTO PROGRAM

To receive SKY 1 you need a satellite tuner.

You must have the satellite tuner set to SKY

1 before starting the AUTO PROGRAM

function.

You can automatically store the TV channels

for which you have the best reception. Store

them in the TV’s programme numbers (PR)

list by doing the following.

After the TV channels have been

registered in the programme

numbers (PR), the EDIT menu

appears.

• You can now edit the programme

numbers (PR) using the EDIT/

MANUAL function. For details, see

“EDIT/MANUAL” on page 42.

• If you do not need to use the EDIT/

MANUAL function, go to the next

step.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

• In some areas you may get TV

reception from more than one

If “ACI START/ACI SKIP” appears

in the AUTO PROGRAM menu:

You can use the ACI (Automatic Channel

Installation) function to decode the ACI

data and complete the registration of all

the TV channels quickly. For details of

the ACI function and how to use it, see

“Using the ACI function” on page 47.

If you don’t want to use the ACI function,

press the 6 buttons to choose ACI

SKIP and then press a.

transmitter, for example, different ITV

regions. In this case each TV channel

could be set twice. If this happens, the

first set of channels will have the

stronger signal. If you want to delete

the second set of channels, you will

have to do it manually (see page 45).

„ EDIT/MANUAL

The EDIT/MANUAL functions are divided

into two types:

• editing the current programme numbers

(PR) (EDIT functions); and

4 Press the a button to display the

T-V LINK menu

• manually storing a TV channel you want

to view on a particular programme

number (PR) (MANUAL function).

Here are the details about these functions:

Caution

• Using the MOVE, DELETE or INSERT

functions rewrites the current programme

numbers (PR) list. Therefore, the

programme numbers (PR) of some of the

TV channels will change.

• Using the MANUAL function for a TV

channel for which the CHILD LOCK

function has been set cancels the CHILD

LOCK function for that channel.

• Using the MANUAL function for a TV

channel for which the DECODER (EXT-2)

function has been set to ON returns the

setting of the DECODER (EXT-2) function

for that channel to OFF.

5 If you do not have a T-V LINK

compatible VCR connected:

Press the b button to leave the T-V

LINK menu.

The T-V LINK menu disappears and all

the settings are completed.

If you have a T-V LINK compatible

VCR connected to the EXT-2

terminal:

See “Downloading data to a VCR” on

page 48 to transmit the programme

number (PR) data to the VCR.

• When a TV channel has already been

registered in PR 99, using the INSERT

function deletes that TV channel.

• If a TV channel you want to view is

not set to a programme number (PR),

set it manually using the MANUAL

function. For details, see “EDIT/

MANUAL” on page 42.

1 Choose EDIT/MANUAL, then press

the a button

• The AUTO PROGRAM function does

not set the programme number PR 0

(AV) for your video cassette recorder.

You will need to set this using the

manual function.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

4 If you do not have a T-V LINK

• For programme number PR 0, “AV”

appears in the programme numbers

(PR) list.

• An EXT terminal number does not

appear in the programme numbers

(PR) list.

• The CH/CC number is a number

unique to the TV and corresponds to

the channel number of a TV channel.

For the relationship between a channel

number and a CH/CC number, see

“CH/CC NUMBER” on page 46.

compatible VCR connected:

Press the b button to exit the T-V LINK

menu.

The T-V LINK menu disappears and all

the settings are completed.

If you have a T-V LINK compatible

VCR connected:

Follow the operating procedure

“Downloading data to a VCR” on page 48

to transmit the programme number (PR)

data to the VCR.

2 Follow the description for a

function you want to use

MOVE

1 Press the 6 buttons to choose a

TV channel

MOVE:

This function changes a programme

number (PR) of a TV channel.

Every time you press the 6 buttons, the

programme number (PR) changes and the

picture of the TV channel stored in the

programme number (PR) appears on the

screen.

ID:

This function registers a channel name

(ID) to a TV channel.

INSERT:

2 Press the 3 button to start the

This function adds a new TV channel in

the current programme numbers (PR) list

by using the CH number.

MOVE function

• You cannot use the INSERT function

if you do not know a channel number

of a TV channel. Use the MANUAL

function to register a TV channel in the

programme number (PR).

DELETE:

This function deletes a TV channel you do

not want to list.

3 Press the 6 buttons to choose a

MANUAL:

This function manually stores a new TV

channel in a programme number (PR).

new programme number (PR)

To cancel the MOVE function:

Press the

(Information) button.

3 Press the a button to complete

the settings

4 Press the 2 button to change the

programme number (PR) of a TV

channel to a new programme

number (PR)

The T-V LINK menu appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

5 Press the 6 buttons to choose

the channel name (ID)

1 Press the 6 buttons to choose a

TV channel

To cancel the ID function:

Every time you press the 6 buttons, the

programme number (PR) changes and the

picture of the TV channel stored in the

programme number (PR) appears on the

screen.

Press the

(Information) button.

6 Press the a button to give a

channel name (ID) to a TV channel

• You can give your own unique channel

name (ID) to the TV channel. When

you have finished step 3, do not go to

step 4. Press the 5 buttons to move

the cursor, and press the 6 buttons

to choose each character of the channel

name (ID). Then press the a button

to register the channel name (ID) to the

TV channel.

2 Press the red button to start the ID

function

INSERT

Preparation:

3 Press the 6 buttons to choose

the first character of a channel

name (ID) you want to give the TV

channel

• You need to find the CH/CC number for

the TV channel. Find the CH/CC number

from the “CH/CC NUMBER” table on

page 46 based on the channel number of

the TV channel.

1 Press the 6 buttons to choose a

programme number (PR) for which

you will register a new TV channel

2 Press the green button and start

the INSERT function.

4 Press the blue button to display the

ID LIST (channel name list)

To cancel the INSERT function:

Press the

(Information) button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

MANUAL

3 When the COUNTRY setting is

UNITED KINGDOM:

1 Press the 6 buttons to choose a

programme number (PR) for a new

TV channel

Press the number buttons to enter

the remaining CH number

• You cannot enter CC numbers.

When the COUNTRY setting is

IRELAND:

2 Press the blue button to activate

the MANUAL function

Press the 6 buttons to choose

“CH” or “CC”, then enter the

remaining CH or CC number

The TV shifts to registration mode.

When the registration is completed, the

picture of the TV channel appears on the

screen.

• The CH/CC number is a number given

to each broadcast frequency that

carries a TV channel. If the TV cannot

detect the TV channel corresponding

to the broadcast frequency indicated

by the CH/CC number, a “no-signal”

picture appears.

To cancel the MANUAL function:

Press the

(Information) button.

When the COUNTRY setting is

IRELAND:

At the right side following the CH/CC

number, the SYSTEM (broadcasting

system) of the TV channel appears.

DELETE

1 Press the 6 buttons to choose a

TV channel

3 When the COUNTRY setting is

UNITED KINGDOM:

Every time you press the 6 buttons, the

programme number (PR) changes and the

picture of the TV channel stored in the

programme number (PR) appears on the

screen.

Continue to step 4

When the COUNTRY setting is

IRELAND:

Press the 3 button to choose the

SYSTEM (broadcasting system) for

a TV channel you want to register

If you do not know the correct

broadcasting system, set the SYSTEM to

“I”. If “I” is not correct, you will not hear

the sound normally when the TV detects a

TV channel. In this case, retry to set the

SYSTEM correctly so that no problem

arises.

2 Press the yellow button to delete

the TV channel

The TV channel is deleted from the

programme numbers (PR) list.

4 Press the green or red button to

search for a TV channel

Scanning stops when the TV finds a TV

channel. Then the TV channel is

displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s menu

Channel

E2, IR A

E3, IR B

E4, IR C

E5, IR D

E6, IR E

E7, IR F

E8, IR G

Channel

E40

E41

E42

E43

E44

E45

E46

E47

E48

E49

E50

E51

E52

E53

E54

E55

E56

E57

E58

E59

E60

E61

E62

E63

E64

E65

E66

E67

E68

E69

5 Press the green or red button

repeatedly until the TV channel you

want appears

CH 02

CH 03

CH 04

CH 05

CH 06

CH 07

CH 08

CH 09

CH 10

CH 11

CH 12

CH 21

CH 22

CH 23

CH 24

CH 25

CH 26

CH 27

CH 28

CH 29

CH 30

CH 31

CH 32

CH 33

CH 34

CH 35

CH 36

CH 37

CH 38

CH 39

CH 40

CH 41

CH 42

CH 43

CH 44

CH 45

CH 46

CH 47

CH 48

CH 49

CH 50

CH 51

CH 52

CH 53

CH 54

CH 55

CH 56

CH 57

CH 58

CH 59

CH 60

CH 61

CH 62

CH 63

CH 64

CH 65

CH 66

CH 67

CH 68

CH 69

If the TV channel reception is poor:

Press the blue or yellow button to fine-

tune the TV channel.

E10, IR H

E11, IR J

E12

6 Press the a button and register

the TV channel to a Programme

number (PR)

E21

E22

E23

The normal EDIT menu is resumed.

E24

E25

„ CH/CC NUMBER

E26

E27

• When you want to use the INSERT

function on page 44, find the CH/CC

number corresponding to the channel

number of the TV channel from this table.

If you want to know a particular TV

channel’s channel menu, look in TV

listings magazines or contact the

broadcaster.

• When the COUNTRY setting is UNITED

KINGDOM, the CC number channels and

the channels from CH/CC 02 to CH/CC 12

cannot be received.

E28

E29

E30

E31

E32

E33

E34

E35

E36

E37

E38

E39

Channel

S31

S32

S33

S34

S35

S36

S37

S38

S39

S40

S41

CC 01

CC 02

CC 03

CC 04

CC 05

CC 06

CC 07

CC 08

CC 09

CC 10

CC 11

CC 12

CC 13

CC 14

CC 15

CC 16

CC 17

CC 18

CC 19

CC 20

CC 21

CC 22

CC 23

CC 24

CC 25

CC 26

CC 27

CC 28

CC 29

CC 30

CC 31

CC 32

CC 33

CC 34

CC 35

CC 36

CC 37

CC 38

CC 39

CC 40

CC 41

CC 75

CC 76

CC 77

CC 78

CC 79

S10

S11

S12

S13

S14

S15

S16

S17

S18

S19

S20

S21

S22

S23

S24

S25

S26

S27

S28

S29

S30

Z+1

Z+2

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional menu operations

2 When the settings are completed,

Using the ACI function

the EDIT menu is displayed. Return

to the instructions that you were

reading before, and continue the

operation

This TV has an ACI function which decodes

the ACI (Automatic Channel Installation)

data.

Using the ACI function allows all TV

channels transmitted from the cable TV

station to be properly registered quickly

according to the data from the cable TV

station.

When the “Initial settings” have

been made:

Return to step 6 of “Initial settings” on

page 7.

When the “AUTO PROGRAM” has

finished:

Caution

• If your cable TV station broadcasts ACI

data and if “ACI START/ACI SKIP”

appears in the AUTO PROGRAM menu,

the ACI function is enabled. In all other

cases, it is disabled.

Return to step 3 of “AUTO PROGRAM”

on page 42.

• If you have any questions about the

items in the Broadcast Selection menu

or how to operate the menu, please

contact your cable TV station.

• When the cable TV broadcast

reception is poor, the ACI function

will not work properly.

• If there is an error in the ACI data

itself, the TV channel cannot be

registered properly. If this happens,

turn the ACI function off (ACI SKIP)

and use the AUTO PROGRAM

function. Or, use the EDIT/MANUAL

function to correct the Programme

number (PR) setting.

1 Press the 6 buttons to choose

ACI START. Then press the a

button to start the ACI function

When you don’t want to use the ACI

function:

Press the 6 buttons to choose ACI

SKIP and then press the a button.

If the AUTO PROGRAM menu

changes to another menu:

Depending on your cable TV station,

there may be a broadcast selection menu

set up by the cable TV station.

Follow the menu and use the 5 and

6 buttons. After you have made the

setting, press the a button.

If “ACI ERROR” is displayed in the

AUTO PROGRAM menu:

“ACI ERROR” means that the ACI

function is not working properly. Press

the a button to start the ACI function

again.

If “ACI ERROR” still appears even after

you have tried to start the ACI function

several times, press the 3 button to start

the AUTO PROGRAM function. It does

not cause any problem because all the TV

channels are registered to the Programme

numbers (PR) by the AUTO PROGRAM

function.

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional menu operations

Downloading data to a VCR

Using the DECODER (EXT-2)

function

You can send the latest programme numbers

(PR) data to a VCR with the T-V LINK

function.

• You can only do this when a T-V LINK

compatible VCR is connected to the EXT-2

terminal.

If you have a decoder connected to a T-V

LINK compatible VCR, which in turn is

connected to the EXT-2 terminal, use the

DECODER (EXT-2) function to unscramble

the scrambled TV channels.

• This only works when the T-V LINK

menu is being displayed.

1 Turn on the decoder power

2 Display the scrambled TV channel

on the TV

Even if the decoder is working, a

scrambled picture appears.

3 Press the a button to display the

1 Turn on the VCR

The MENU (main menu) appears.

2 Press the a button

4 Press the 6 buttons to choose

FEATURES. Then press the a

button

The data transmission begins.

The FEATURES menu appears.

The T-V LINK menu disappears once the

data transmission ends.

When the T-V LINK menu changes

over to another menu:

The TV has finished its menu. This new

menu is operated from the VCR. See the

VCR instruction manual for what to do

next.

5 Press the 6 buttons to choose

DECODER (EXT-2). Then press the

5 buttons to choose ON

If “FEATURE NOT AVAILABLE”

appears at the T-V LINK menu, check the

following three items.

An unscrambled picture appears.

• Has a T-V LINK compatible VCR

been connected to the EXT-2

terminal?

• Has the VCR power been turned on?

• Does the SCART cable that connects

the EXT-2 terminal to the T-V LINK

compatible VCR have all its proper

connections?

To cancel the DECODER (EXT-2)

function:

Press the 5 buttons to choose OFF.

6 Press the a button to complete

the setting

The T-V LINK menu appears.

Then press the a button to retry data

transmission.

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional menu operations

7 Follow “Downloading data to a

VCR” on page 48 to transmit the

programme number (PR) data to

the VCR

8 If you have another TV channel you

want to unscramble using a

decoder, repeat steps 2 to 7

If the DECODER (EXT-2) function has

been set to “ON” but the TV channel

cannot be unscrambled, check the

following:

• Has the decoder been connected to the

VCR properly according to the VCR

and decoder instruction manuals?

• Has the decoder power been turned

on?

• Can the TV channel be unscrambled

with a decoder?

• Do you need to change the VCR

settings in order to connect the

decoder? Confirm that the VCR is set

properly by rechecking the VCR

Instruction manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional preparation

Connecting external equipment

Connect the equipment to the TV, making

the correct rear panel and front panel

connections.

1 VCR (composite signal)

2 VCR (composite signal/S-VIDEO signal)

3 T-V LINK compatible VCR (composite

signal/S-VIDEO signal)

4 Decoder

5 DVD player (composite signal/S-VIDEO

signal)

6 DVD player (composite signal/RGB

signal)

Before connecting anything:

• Read the manuals that came with the

equipment.

Depending on the equipment, the

connection method may be different from

the diagram. Also, the equipment settings

may need to change depending on the

connection method.

7 DVD player (component video signals;

Pr/Pb/Y)

• Turn off all the equipment including the

TV.

• The “Specifications” on the back cover

8 TV game (composite signal/RGB signal)

9 TV game (composite signal/S-VIDEO

signal)

give the details of the EXT terminals. If

you are connecting equipment not listed

in the following connection diagram, see

the table to choose the best EXT terminal.

• Connecting cables are not supplied.

0 Headphones

- Camcorder (composite signal/S-VIDEO

signal)

= SCART cable

~ Audio cable

! Video cable

@ S-VIDEO cable

Back of the TV

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional preparation

„ Equipment which can output the

S-VIDEO signal (Y/C signal) such

as an S-VHS VCR

„ TV output from the EXT-1 terminal

The video/sound signal of a TV channel you

are viewing is always output from the EXT-1

terminal.

Connect the equipment to an EXT terminal

(but not the EXT-1 terminal).

• Changing over a programme number (PR)

also changes over the TV output from the

EXT-1 terminal.

• The video/sound signal from an EXT

terminal cannot be output.

You can choose between an S-VIDEO signal

(Y/C signal) and a regular video signal

(composite signal). For details of how to

operate the equipment, see “S-IN (S-VIDEO

input)” on page 36.

• Teletext programmes cannot be output.

„ T-V LINK compatible VCR

Be sure to connect the T-V LINK compatible

VCR to the EXT-2 terminal. If not, the T-V

LINK function will not work properly.

• When connecting a T-V LINK compatible

VCR to the EXT-2 terminal, be sure to

connect the decoder to the VCR. If not,

the T-V LINK function may not work

properly. After you have stored TV

channels in the programme numbers (PR)

list, set the DECODER (EXT-2) function

for the programme number (PR) to ON to

unscramble a scrambled TV channel. For

details, see “Using the DECODER (EXT-

2) function” on page 48.

„ Connecting headphones

Connect the headphones with a stereo mini-

jack (3.5 mm diameter) to the headphone

socket at the TV rear panel.

• The headphone volume is adjusted with

the “HEADPHONE” menu (see page 28).

„ Video or sound signal output from

the EXT-2 terminal

You can change over the output of the video/

sound signal from the EXT-2 terminal. This

is useful when you want to dub the video/

sound from another device onto the VCR

connected to the EXT-2 terminal. For details

on how to do this, see “DUBBING” on

page 37.

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional preparation

2 Connect the device and set the EXT

terminal to DIGITAL-IN in

accordance with “DIGITAL-IN” on

page 36

Listening to Dolby Digital

audio

To listen to Dolby Digital audio which is

recorded as a Dolby Digital programme

source (such as a DVD-video disc), connect

the device and set the DIGITAL-IN as

described below.

This completes the preparation.

• When an optical input and coaxial

input are input simultaneously, the

optical input takes precedence.

• This TV does not work with digital

audio signals other than Dolby Digital

audio. If no sound is emitted from the

speakers, cancel the DIGITAL-IN

setting and change to normal analog

sound.

Preparation:

• A device (such as DVD player) with a

digital output terminal (coaxial or optical)

for Dolby Digital is necessary.

• A coaxial cable or optical cable is

necessary to make the connections. (Not

supplied with the TV)

• Following the instruction manual which is

supplied with the device, correctly

connect a coaxial cable or optical cable to

the device’s DIGITAL OUT (digital

output) terminal and set the device so that

the Dolby Digital audio signal is output.

• Correctly connect the device to the EXT

terminal in accordance with “Connecting

external equipment” on page 50.

However, since the EXT-4 terminal does

not work with Dolby Digital audio, it

cannot be used.

Using additional audio

equipment

After correctly connecting audio equipment

to the TV, use the TV menu to correctly set

the functions of the audio equipment.

Connect the audio equipment to the

Before connecting anything:

• Read the manuals that came with the

audio equipment.

• Do not turn the power of the TV or

audio equipment on until the

1 Connect the device to the DIGITAL

AUDIO IN terminal with a coaxial

cable 1 or optical cable 2

connections have been completed.

• If the additional speakers are placed

immediately next to the TV, use

magnetically-shielded speakers in

order to prevent magnetism from the

speakers adversely affecting the TV.

• Connecting cables are not supplied.

Back of the TV

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional preparation

Surround speakers 1:

Connect surround speakers to the TV

when you want to use the DOLBY

SURROUND function to enjoy surround

sound.

• Even without surround speakers, you

can easily enjoy surround sound by

using the 3D-PHONIC function.

• Use 8-ohm impedance type speakers.

• Pay attention to the positive (+) and

negative (-) polarities when connecting

surround speakers to your TV.

• For the best effect, position the

surround speakers at least 1 metre

above the heads of seated viewers.

Front speaker system

(Front L/R speakers 2 and

amplifier 3):

You can use your hi-fi audio system

speakers instead of the TV speakers.

Back of the TV

Subwoofer system

(Subwoofer and amplifier 5):

Using the subwoofer system improves the

playing performance of low sounds.

• It is particularly effective with the low

frequency effects (LFE) included in

5.1-channel Dolby Digital surround

sound.

• When a front speaker system and/or

subwoofer system is connected, listen

to the sound from the connected

equipment. Depending on the settings,

it may not be possible to hear the

sound using just the TV speaker. To

listen to the sound from the TV

speaker without using the connected

equipment, change the settings with

one of the following.

Approx.

45 degrees

- Set the SOUND SETTING

SPEAKER to ON, or

- Set the SURROUND FEATURES

3D-PHONIC or DOLBY

SURROUND TV SPEAKER to “L/

C/R”.

To listen to the sound from the

connected equipment after changing

the settings, change the settings back

to match the connected equipment.

Positioning of speakers

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional preparation

• By using the 5 buttons on the TV

Removing and Fitting the

Woofer Unit

remote control or the buttons on the

TV, the volume of all the speakers

including those of the additional audio

equipments can be adjusted

„ Removing the woofer unit

The woofer unit may be removed as

necessary.

simultaneously.

• If the volume of the TV speakers is

different to the volume of the front

speaker system or subwoofer system,

adjust the volumes of each amplifier to

match that of the TV speakers.

Remove the connector while pushing the

connector lever on the woofer terminal, lift

the woofer, and remove it.

Lever

„ Fitting the woofer unit

Fit the woofer unit in the reverse order to that

described in “Removing the woofer unit”.

Align the projection on the base of the

woofer unit with the hole in the top of the

TV, and insert the connector into the woofer

terminal.

„ Cautions when fitting the woofer

unit

• Check that the woofer unit is fitted

correctly on the top of the TV.

• Do not use excessive force when inserting

the connector into the woofer terminal.

Use of excessive force may damage the

connector.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

If a problem arises while you are using the TV, please read this troubleshooting guide carefully

before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example,

if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may

think there is a problem with the TV itself.

Important:

• This troubleshooting guide only covers problems whose causes are not easy to decide. If you

have a question when you are operating a function, read the page(s) for that function carefully,

not this troubleshooting guide.

• If you follow the advice in this troubleshooting guide without any success, unplug the mains

plug and ask for your TV to be repaired. Do not attempt to repair the TV by yourself or to

remove the rear cover of the TV.

• If the TV or aerial suffers interference

from other equipment, stripes or noise

may appear in the picture. Move any

equipment such as an amplifier, personal

computer, or a hair drier, that can cause

interference away from your TV. Or try

moving the TV. If the aerial suffers

interference from a radio tower or high-

voltage wire, please contact your local

dealer.

• If the TV suffers interference from signals

reflecting from mountains or buildings,

double-pictures (ghosting) will occur. Try

to change the aerial’s direction or replace

it with one with better directionality.

• Are your COLOUR SYSTEM settings

correct? Follow the description

„ If you cannot turn on the TV

• Is the mains plug connected to the mains

outlet?

• Is the power lamp lit? If not, press the

main power button.

„ No picture or no sound

• Have you chosen a TV channel with very

poor reception? If so, the BLUE BACK

function will be activated: the entire

screen becomes blue, and the sound is

muted. If you still want to view the TV

channel, follow the description “BLUE

BACK” on page 39 to change the BLUE

BACK function setting to OFF.

• Have you set the SPEAKER function to

OFF? Follow the description

“SPEAKER” on page 27 to check the

“COLOUR SYSTEM” on page 25 to try

to solve the trouble.

SPEAKER function setting.

• Have the COLOUR and BRIGHT settings

been adjusted properly? Follow the

description “Picture Adjustment” on

page 23 to try to adjust them properly.

• Videotaping teletext is not recommended

because it may not record correctly.

• When a white and bright still image (such

as a white dress) is displayed on the

screen, the white part may look as if it is

coloured. This is unavoidable due to the

nature of the picture tube itself, and not

due to a TV failure. When the picture

disappears from the screen, the unnatural

colours will also disappear.

• When viewing images from commercially

available video software products, or

videos from videotapes which have been

recorded improperly, the top of the image

may be distorted. This is due to the

condition of the video signal. There is

nothing wrong with the TV.

If SPEAKER is not displayed, set to

SURROUND OFF with the SURROUND

FEATURES menu and display SOUND

SETTING again.

„ Poor picture

• If noise (snow) totally blocks out the

picture, there may be a problem with the

aerial or aerial cable. Check the following

to try to solve the problem:

–Have the TV and aerial been connected

properly?

–Has the aerial cable been damaged?

–Is the aerial pointing in the right

direction?

–Is the aerial itself faulty?

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

• If you bring magnetised equipment such

as a speaker near to your TV, the picture

may be warped or unnatural colours may

appear at the corners of the screen. In this

case, keep the equipment away from your

TV. If speakers cause this to happen, use

magnetically-shielded speakers instead.

• A picture may be tilted due to the earth’s

magnetic field. If so, use the “PICTURE

TILT” on page 26 to correct the tilt.

• It takes a short period of time from the

time an operation such as changing

channels is performed until an image is

displayed. This is not a malfunction. This

is the time required for the image to

stabilize before it can be displayed.

• The TV may make a crackling sound due

to a sudden change in temperature. The

picture or sound may be normal. If you

hear crackling sounds frequently while

you are viewing the TV, there may be

other causes. As a precaution, ask your

service technician to inspect it.

• Touching the screen may cause you to

feel a slight electric shock due to its static

electricity. This is unavoidable due to the

construction of the picture tube. It is not a

problem with the TV. You can rest

assured that this static discharge is not

harmful.

• In the twin pictures mode the sub-picture

may disappear when the external device is

operated. If this happens, press the P

button and display the sub-picture again.

• The headphone volume is adjusted with

the “HEADPHONE” menu. It cannot be

adjusted with the 5 buttons or r

(volume) q buttons.

„ Poor sound

• Have you adjusted BASS or TREBLE

properly? If not, follow the description

“Sound Adjustment” on page 27.

• When TV channel reception is poor, it can

be hard to hear stereo or bilingual sound.

In this case, follow the description

“STEREO / I • II” on page 27 to hear the

sound more easily by changing it to a

mono sound.

„ If the TV does not respond to the

remote control

• Have the batteries of the remote control

worn out? Follow the description “Putting

the batteries into the Remote control” on

page 6 and replace them with new

batteries.

• Have you attempted to use the remote

control from the sides or rear of the TV or

from more than seven metres away from

the TV? Use the remote control in the

front of your TV or from less than seven

metres away.

• When you are viewing a teletext

programme, you cannot operate the

menus. Press the b button to return to

the ordinary TV programme, and then try

operating the menus.

• If the TV suddenly stops responding,

press the main power button on the TV

and turn off the main power. Press the

main power button again to turn on the

TV. If the TV returns to a normal state, it

is not a failure.

„ Other issues

• When the SLEEP TIMER function

operates, the TV is automatically turned

off. If the TV suddenly turns off, try to

press the # (standby) button to turn on

the TV once again. If the TV goes back to

normal, there is no problem.

• When the TV is receiving a wide-screen

signal (WSS) or a signal from an external

device affecting the screen size, the

ZOOM mode automatically changes.

When you want to resume the previous

ZOOM mode, press the c button

again.

• When TV SPEAKER in the

“HEADPHONE” menu is ON, even if the

headphones are connected, sound is

emitted from the TV speaker. When you

do not want to emit sound from the TV

speaker, turn the setting OFF.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Model

HV-32D25EJ*

When the COUNTRY setting is When the COUNTRY setting is

UNITED KINGDOM IRELAND

CCIR B/G, I, D/K, L

PAL, SECAM

COUNTRY setting

Broadcasting systems

Colour systems

CCIR I

PAL

• The EXT terminals also support the • The EXT terminals also support the

NTSC 3.58/4.43 MHz system.

Channels and frequencies

Sound-multiplex systems

Teletext systems

E21-E69

IR A-J, E2-E12, E21-E69, S1-S41, X,

Y, Z, Z+1, Z+2

NICAM (B/G, I, D/K, L) system,

A2 (B/G, D/K) system

FLOF (Fastext), TOP,

WST (World Standard System)

NICAM (I) system

FLOF (Fastext),

WST (World Standard System)

Power requirements

Power consumption

Picture tube size

Audio output

220 - 240 V AC, 50 Hz

Maximum: 310 W, Average: 169 W, Standby: 2.5 W

Viewable area 76 cm (measured diagonally)

Rated Power output: 10 W + 10 W + 7.5 W, 18 W (Woofer)

(13 cm × 6.5 cm) oval × 2, (16 cm × 4 cm) oval × 1, 13 cm round woofer × 1

Speakers

EXT-1 terminal

Euroconnector (21-pin, SCART)

• Video input, Audio L/R inputs and RGB inputs are available.

• TV broadcast outputs (Video and Audio L/R) are available.

EXT-2 terminal

Euroconnector (21-pin, SCART)

• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are

available.

• Video and Audio L/R outputs are available.

• T-V LINK functions are available.

EXT-3 terminal

EXT-4 terminal

Euroconnector (21-pin, SCART)

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

RCA connectors × 5

• Component video (Pr, Pb, Y) inputs and Audio L/R inputs are available.

• progressive-scanning signals (625p or 525p) are available.

EXT-5 terminal

RCA connectors × 3

S-VIDEO connector × 1

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

AUDIO OUT terminal

RCA connectors × 3

• Variable audio L/R outputs and subwoofer output are available.

• Variable out 0-1 Vrms, low impedance.

SURROUND REAR terminal Speaker terminals for external surround speakers.

• Surround rear sounds are output to the speakers.

• For impedance 8-ohm speakers only.

• Rated power output: 7.5 W + 7.5 W

DIGITAL AUDIO IN terminal Coaxial connector × 1

Optical connector × 1

• Dolby Digital is available.

Headphone jack

Dimensions (W × H × D)

Weight

Stereo mini-jack (3.5 mm in diameter)

946 mm × 562 mm × 551 mm

58.0 kg

Accessories

Remote control unit × 1 (RM-C62)

AAA/R03 dry cell battery × 2

*: A basic model number. The actual model number may have characters added (such as “S”

denoting silver) indicating the colour of the TV set.

We may change the design and specifications without notice.

Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any

commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of

the owners of copyright of the original picture sources, as this would be an infringement of

Download from Www.Somanuals.com. All Manuals Search And Download.

Invacare Mobility Aid Arrow RWD User Manual
Jacuzzi Hot Tub 7260 User Manual
JBL Speaker MkII automotive User Manual
JL Audio Car Speaker 15W0v2 User Manual
JVC CD Player RV DP200BK User Manual
JVC DVR GR DVL317 User Manual
JVC Home Theater System SP PWS51 User Manual
Kenwood Cassette Player KRC 177RA User Manual
Kenwood CD Player DPC 885 User Manual
Keurig Coffeemaker B3000 User Manual