JVC CRT Television AV 32DF74 User Manual

Color Television Users Guide

For Models:

AV-36DF74

AV-32DF74

Illustration of AV-32DF74 and RM-C1201G

Important Note:

In the spaces below, enter the model and serial number of your television (located

at the rear of the television cabinet). Staple your sales receipt or invoice to the

inside cover of this guide. Keep this user’s guide in a convenient place for future

reference. Keep the carton and original packaging for future use.

Model Number:

LCT1404-001A-A

Serial Number:

0503-TN-II-IM

Download from Www.Somanuals.com. All Manuals Search And Download.

• As an “ENERGY STAR ” partner,

JVC has determined that this

product or product model meets the

“ENERGY STAR ” guidelines for energy

efficiency.

Important Safeguards

CAUTION:

Please read and retain for your safety.

Electrical energy can perform many useful functions. This TV set has been engineered and

manufactured to assure your personal safety. But improper use can result in potential

electrical shock or fire hazards. In order not to defeat the safeguards incorporated in this

TV set, observe the following basic rules for its installation, use and servicing. Also follow all

warnings and instructions marked on your TV set.

INSTALLATION

(POLARIZED-TYPE)

1 Your TV set is equipped with a polarized AC line plug (one

blade of the plug is wider than the other). This safety feature

allows the plug to fit into the power outlet only one way.

Should you be unable to insert the plug fully into the outlet,

try reversing the plug. Should it still fail to fit, contact your

electrician.

2 Operate the TV set only from a power source as indicated on the TV set or refer to the

operating instructions for this information. If you are not sure of the type of power supply to

your home, consult your TV set dealer or local power company. For battery operation, refer

to the operating instructions.

3 Overloaded AC outlets and extension cords are dangerous, and so are frayed power cords

and broken plugs. They may result in a shock or fire hazard. Call your service technician for

replacement.

4 Do not allow anything to rest on or roll over the power cord, and do not place the TV set

where power cord is subject to traffic or abuse. This may result in a shock or fire hazard.

5 Do not use this TV set near water — for example, near a bathtub, washbowl, kitchen sink, or

laundry tub, in a wet basement, or near swimming pool, etc.

6 If an outside antenna is connected to the TV set, be sure the antenna system is grounded

so as to provide some protection against voltage surges and built-up static charges.

Section 810 of the National Electrical Code provides information with respect to proper

grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna

discharge unit, size of grounding conductors, location of antenna discharge unit, connection

requirements for the grounding electrode.

Download from Www.Somanuals.com. All Manuals Search And Download.

7 An outside antenna system should not be located in the vicinity of overhead power lines

or other electric light or power circuits, or where it can fall into such power lines or circuits.

When installing an outside antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL ELECTRICAL CODE

8 TV sets are provided with ventilation openings in the cabinet to allow heat generated during

operation to be released.

Therefore:

— Never block the bottom ventilation slots of a portable TV set by placing it on a bed, sofa,

rug, etc.

— Never place a TV set in a “built-in” enclosure unless proper ventilation is provided.

— Never cover the openings with a cloth or other material.

— Never place the TV set near or over a radiator or heat register.

9 To avoid personal injury:

— Do not place a TV set on a sloping shelf unless properly secured.

— Use only a cart or stand recommended by the TV set manufacturer.

— Do not try to roll a cart with small casters across thresholds or deep pile carpets.

— Wall or shelf mounting should follow the manufacturer’s instructions, and should use a

mounting kit approved by the manufacturer.

Use

10 Caution children about dropping or pushing objects into the TV set through cabinet

openings. Some internal parts carry hazardous voltages and contact can result in a fire or

electrical shock.

11 Unplug the TV set from the wall outlet before cleaning. Do not use liquid or an aerosol

cleaner.

12 Never add accessories to a TV set that has not been designed for this purpose. Such

additions may result in a hazard.

Download from Www.Somanuals.com. All Manuals Search And Download.

PORTABLE CART WARNING

(Symbol provided by RETAC)

13 For added protection of the TV set during a lightning storm or when the TV set is to be left

unattended for an extended period of time, unplug it from the wall outlet and disconnect the

antenna. This will prevent damage to product due to lightning storms or power line surges.

14 A TV set and cart combination should be moved with care. Quick stops, excessive force,

and uneven surfaces may cause the TV set and cart combination to overturn.

Service

15 Unplug this TV set from the wall outlet and refer servicing to qualified service personnel

under the following conditions:

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the TV set.

C. If the TV set has been exposed to rain or water.

D. If the TV set does not operate normally by following the operating instructions. Adjust

only those controls that are covered in the operating instructions as improper adjustment

of other controls may result in damage and will often require extensive work by a

qualified technician to restore the TV set to normal operation.

E. If the TV set has been dropped or damaged in any way.

F. When the TV set exhibits a distinct change in performance — this indicates a need for

service.

16 Do not attempt to service this TV set yourself as opening or removing covers may

expose you to dangerous voltage or other hazards. Refer all servicing to qualified service

personnel.

17 When replacement parts are required, have the service technician verify in writing that the

replacement parts he uses have the same safety characteristics as the original parts. Use

of manufacturer’s specified replacement parts can prevent fire, shock, or other hazards.

18 Upon completion of any service or repairs to this TV set, please ask the service technician

to perform the safety check described in the manufacturer’s service literature.

19 When a TV set reaches the end of its useful life, improper disposal could result in a picture

tube implosion. Ask a qualified service technician to dispose of the TV set.

20 Note to CATV system installer.

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of

the NEC that provides guidelines for proper grounding and, in particular, specifies that the

cable ground shall be connected to the grounding system of the building, as close to the

point of cable entry as practical.

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Quick Setup . . . . . . . . . . . 7

Sound Adjust . . . . . . . . . 44

Unpacking your TV . . . . . . . . . . . . 7

TV Models . . . . . . . . . . . . . . . . 8

TV Remote Control . . . . . . . . . . . 9

Getting Started . . . . . . . . . . . . . 10

The Remote Control . . . . . . . . . . 10

Connecting Your Devices . . . . . . . 11

Interactive Plug In Menu . . . . . . . . 19

Sound Settings . . . . . . . . . . . . . 44

Adjust Sound Settings . . . . . . . . . 44

MTS (Multi-channel Sound) . . . . . . . 44

Reset . . . . . . . . . . . . . . . . . . 44

Clock Timers . . . . . . . . . . 45

Set Clock . . . . . . . . . . . . . . . . 45

On/Off Timer . . . . . . . . . . . . . . . 46

Remote Programming . . . . . 22

Button Functions . . . . . . . 47

Setting CATV, VCR and DVD Codes . . . 22

CATV or Satellite Codes . . . . . . . . 22

VCR Codes . . . . . . . . . . . . . . 23

DVD Codes . . . . . . . . . . . . . . 24

Search Codes . . . . . . . . . . . . . 25

Multi Screen Function . . . . . . . . . . 47

PIP/Move . . . . . . . . . . . . . 47

Index . . . . . . . . . . . . . . . . 48

Freeze . . . . . . . . . . . . . . . 48

Swap . . . . . . . . . . . . . . . . 48

Select . . . . . . . . . . . . . . . . 48

EZ-Surf . . . . . . . . . . . . . . . 48

Power . . . . . . . . . . . . . . . . . . 49

Number Buttons . . . . . . . . . . . . . 49

100+ Button . . . . . . . . . . . . . . . 49

Channel +/- . . . . . . . . . . . . . . 49

Volume +/- . . . . . . . . . . . . . . . 49

Input . . . . . . . . . . . . . . . . . . . 49

Digital-In . . . . . . . . . . . . . . . . . 49

Onscreen Menus . . . . . . . . 26

Using the Guide . . . . . . . . . . . . . 26

Onscreen Menu System . . . . . . . . . 27

Initial Setup . . . . . . . . . . 29

Auto Tuner Setup . . . . . . . . . . . . 29

Channel Summary . . . . . . . . . . . . 29

V-Chip . . . . . . . . . . . . . . . . . . 30

Set Lock Code . . . . . . . . . . . . . 36

Auto Demo . . . . . . . . . . . . . . . 36

Language . . . . . . . . . . . . . . . . 37

Closed Caption . . . . . . . . . . . . . 37

Auto Shut Off . . . . . . . . . . . . . . 38

XDS ID . . . . . . . . . . . . . . . . . 38

Tilt Correction . . . . . . . . . . . . . . 38

Light

Return +/TV . . . . . . . . . . . . . . . 50

Sound . . . . . . . . . . . . . . . . . . 50

Muting . . . . . . . . . . . . . . . . . . 50

Video Status . . . . . . . . . . . . . . . 51

Natural Cinema . . . . . . . . . . . . . 51

TheaterPro D6500K . . . . . . . . . . . 51

Sleep Timer . . . . . . . . . . . . . . . 52

Display . . . . . . . . . . . . . . . . . 52

Aspect . . . . . . . . . . . . . . . . . 53

Aspect Ratios . . . . . . . . . . . . . 53

C.C. . . . . . . . . . . . . . . . . . . . 54

Menu . . . . . . . . . . . . . . . . . . 54

OK . . . . . . . . . . . . . . . . . . . 54

Back . . . . . . . . . . . . . . . . . . . 54

TV/CATV Slide Switch . . . . . . . . . . 55

VCR/DVD Slide Switch . . . . . . . . . 55

VCR Buttons . . . . . . . . . . . . . . . 55

DVD Buttons . . . . . . . . . . . . . . . 55

Purity

Noise Muting . . . . . . . . . . . . . . 39

Front Panel Lock . . . . . . . . . . . . 39

V1 Smart Input . . . . . . . . . . . . 40

TV Speaker . . . . . . . . . . . . . . . 40

Audio Out . . . . . . . . . . . . . . . . 40

Center CH Input . . . . . . . . . . . . . 41

Digital-In . . . . . . . . . . . . . . . . . 41

Picture Adjust . . . . . . . . . 42

Picture Settings . . . . . . . . . . . . . 42

Adjust Picture Settings . . . . . . . . . 42

Color Temperature . . . . . . . . . . . . 42

Digital Noise Clear . . . . . . . . . . . . 43

VSM . . . . . . . . . . . . . . . . . . . 43

Reset . . . . . . . . . . . . . . . . . . 43

Appendices . . . . . . . . . . 56

Troubleshooting . . . . . . . . . . . . . 56

Warranty . . . . . . . . . . . . . . . . . 57

Authorized Service Centers . . . . . . . 59

Specifications . . . . . . . . . . . . . 60

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Unpacking your TV

Thank you for your purchase of a JVC Color Television. Before you begin setting up your new

television, please check to make sure you have all of the following items. In addition to this

guide, your television box should include:

Two AA

Batteries

1 Remote Control

1 Television

��

�

��

�

��

Note: Your television

and/or remote

��

control may differ

from the examples

illustrated here.

��

Once you have unpacked your television, the next step is to connect it to your antenna/

cable or satellite system and to connect the audio/video devices you want to use with your

television. To make these connections you will use plugs like the ones illustrated below.

Component Cables

Composite Cables

Audio Cables

Coaxial Cables

Used to connect an

external antenna or

cable TV system to

your TV.

Used to connect audio/

video devices like

VCRs, DVD players,

stereo amplifiers, game

consoles, etc.

S-Video Cable

AV CompuLink Cable

Used to make video

connections with S-Video

VCRs, Camcorders and

DVD players.

Used to connect JVC

AV CompuLink capable components

for an automated home theater.

We recommend that before you start using your new television, you read your entire User’s

Guide so you can learn about your new television’s many great features. If you’re anxious to

start using your television right away, a quick setup guide follows on the next few pages.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

TV Models

NOTE: Before you connect your television to another device, please refer to the proper

diagrams for your specific TV and remote. These will help assist you in understanding

how to connect your television to another device, as well as use the remote to set up

your television.

Rear Panel Diagram

MODELS:

AV-36DF74

AV-32DF74

��

�

��

�

��

�

��

Front Panel Diagram

��

MODELS: AV-36DF74, AV-32DF74

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

TV Remote Control

��

�

��

�

��

RM-C1201G

MODELS:

AV-36DF74

AV-32DF74

• For information on remote control buttons, see pages 47 - 55.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Getting Started

These quick setup pages will provide you, in three easy steps, with the basic information you

need to begin using your new television right away.

If you have questions, or for more detailed information on any of these steps, please consult

other sections of this manual.

Step 1 – The Remote Control

Before you can operate your remote

control, you first need to install the

batteries (included).

Slide the cover on the back of the

remote down towards the bottom of

the remote control. Insert two batteries

(included) carefully noting the “+” and

“–” markings, placing the “–” end in the

unit first. Slide the cover back into place.

When you change the batteries, try

to complete the task within three minutes. If you take longer than three minutes, the

remote control codes for your VCR, DVD, and/or cable box/satellite receiver may have to

be reset. See pages 22 - 25.

Key Feature Buttons

The four key feature buttons at the center of the remote

can be used for basic operation of the television. The top

and bottom buttons will scan forward and back through the

available channels. To move rapidly through the channels

using JVC’s Hyperscan feature, press and hold CH+ or

CH–. The channels will zip by at a rate of five channels per

second. The right and left buttons will turn the volume up or

down. These buttons are also marked with four arrows and

are used with JVC’s onscreen menu system. To use the

onscreen menus, press the MENU button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connections

��

Basic Operation

Turn the television on and off by pressing the POWER button at the top right corner

of the remote. If this is the first time you are turning on the TV, the interactive

plug-in menu appears.

��

• Make sure the TV/CATV switch is set to TV. Move the switch to CATV only if

you need to operate a cable box.

• Slide the VCR/DVD selector switch to VCR to control a VCR. Slide to

DVD to control a DVD player. Please see pages 22 to 25 for instructions on

programming your remote control to operate a cable box, VCR or DVD player.

��

Step 2 – Connecting Your Devices

Please follow the flow chart below to determine which connection setup is right for you. Then,

refer to the appropriate diagrams to connect your television to other devices that you may

have. After you are finished connecting your devices, plug the power cord into the nearest

power outlet and turn on the TV.

A VCR is not necessary for operation of the television. If you follow these diagrams and the

television does not work properly, contact your local cable operator.

• To connect a DVD player, see Diagram #3. A DVD player is optional.

• If you have a satellite television system, please refer to the satellite TV manual.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connections

Diagram #1

��

��Ω

��

Note:

• If you do not have a cable box, connect the cable wire from the wall outlet into the back of

the TV.

Diagram #2

��

��Ω

��

Notes:

• If your VCR is a mono sound unit, it will have only one audio out jack. Connect it to the

LEFT AUDIO INPUT on the front of the TV.

• Use the S-Video connection if possible for superior picture quality.

• Your VCR must be turned on to view premium cable channels.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connections

Notes:

• Green, blue and red are the most common colors for DVD cables. Some models may vary

colors. Please consult the user’s manual for your DVD player for more information.

• Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete

one set of connections (DVD or audio output) before starting the other to avoid accidentally

switching the cables.

• You may also connect the DVD player to Input 1.

Diagram #3

��

��Ω

��

�

��

�

��

�

��

�

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connections

Connecting to JVC AV CompuLink

JVC’s AV CompuLink feature makes playing video tapes or DVDs totally automatic. Simply

insert a pre-recorded tape into your JVC brand VCR or DVD into your JVC DVD player

and the device will automatically turn on and begin playback. At the same time, using the

AV CompuLink, the VCR or DVD player sends a signal to the television telling it to turn on

and switch to the proper video input.

• The AV CompuLink cable may be included with the JVC AV CompuLink unit you

wish to connect. If it is not, contact JVC Parts Department at (800)-882-2345, or

www.jvcservice.com for part # EWP 805-012.

• AV CompuLink can only be used with JVC brand products.

To Connect: Plug one end of the AV CompuLink cable

AV Compu Link Cable

into the AV COMPULINK INPUT on your VCR, DVD, or

other CompuLink device. Plug the other end of the

AV CompuLink cable into the AV COMPULINK at the

rear of the television.

Note:

• The AV CompuLink cable has a male 3.5 mm (mono)

plug on each end.

��

Notes:

• In order for the VCR playback to begin automatically, the recording tabs must be removed

from the VHS tape. If the tab is in place, automatic switching will occur when you push the

VCR’s PLAY button.

• If your JVC brand VCR has “A code/B code remote control switching” (see your VCR’s

instruction book), using VCR A code will switch the TV to input 1.

• Refer to your DVD instruction book for detailed connection information.

• To connect a JVC HiFi receiver or amplifier for a completely automated home theater, see

the receiver connection instructions for detailed connection information.

• AV CompuLink is compatible with select AV CompuLink receivers.

• In order to use the AV CompuLink function, make sure you have V1 SMART INPUT turned

OFF in the INITIAL SETUP MENU.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connections

Connecting to a Camcorder

You may connect a camcorder, game console or other equipment to your television by using

the front input jacks (Input 4) located under the front panel door. To access, push on the door

to open it. You can also connect these using the television’s rear input jacks, using the same

instructions.

��

1) Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on

the front of the TV, OR connect an S-Video cable from the front of the TV to the camcorder.

2) Connect a white cable from the camcorder LEFT AUDIO OUT, into the LEFT AUDIO IN on

the front of the TV.

3) Connect a red cable from the camcorder RIGHT AUDIO OUT, into the RIGHT AUDIO IN on

the front of the TV.

Note:

• If your camcorder is a mono sound model it will have only one AUDIO OUT. Connect it to the

LEFT AUDIO IN on the front of the TV.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connections

Connecting to an External Amplifier

Subwoofer Out - Use a powered subwoofer with the surround feature to simulate a home

theater system. Simply connect the subwoofer to the back of the TV.

��

1) Connect a white cable from the LEFT AUDIO OUTPUT on the back of the TV to the

LEFT AUDIO INPUT on the amplifier.

2) Connect a red cable from the RIGHT AUDIO OUTPUT on the back of the TV to the

RIGHT AUDIO INPUT on the amplifier.

3) Connect a black cable from the SUBWOOFER OUT on the back of the TV to

the LINE INPUT of the subwoofer.

Notes:

• Refer to your amplifier’s manual for more information.

• You can use AUDIO OUTPUT for your home theater system.

Connecting to the Surround Amplifier

Note: Please read the benefit of this feature on page 41.

��

��Ω��

��

1) Connect the black speaker cable from the TV’s SPEAKER INPUT

terminal to the

�

surround amplifier’s CENTER SPEAKER OUTPUT

terminal.

�

2) Connect the red speaker cable from the TV’s SPEAKER INPUT

terminal to the

�

surround amplifier’s CENTER SPEAKER OUTPUT

terminal.

�

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connections

Connecting to a Digital TV Receiver w/HDCP

By inputting a high bandwidth digital content protection high definition picture source to the

digital-in terminal of this television, high-definition pictures can be displayed on the screen in

their digital form. (This terminal is for use in the future when high bandwidth digital content

protection DTV decoders and DVD players and D-VHS are put on the market.)

��

�

��

�

��

�

��

�

1) Connect the DTV DIGITAL RGB OUTPUT TERMINAL to the DIGITAL INPUT TERMINAL of

the television, and then tighten the 2 screws.

2) Connect the DTV decoder LEFT AUDIO OUTPUT to the DIGITAL-IN LEFT AUDIO INPUT.

3) Connect the DTV decoder RIGHT AUDIO OUTPUT to the DIGITAL-IN RIGHT AUDIO

INPUT.

• The digital-in terminal is not compatible with the picture signal of a personal computer.

• Use a DVI-D single link 19-pin cable (commercially available) in order to digitally connect the

television with a DTV decoder.

If 480p signals (640x480 or 720x480) are displayed on the screen, the horizontal balance may

be slightly shifted. In cases such as this, the horizontal balance can be adjusted by accessing

“DIGITAL-IN” in the INITIAL SETUP menu. (Refer to page 41.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connections

Connecting to an AV Receiver using your television's

V1 Smart Input

By connecting your AV Receiver to your television's V1 Smart Input, you can watch picture

sources from many different devices, without having to change or use the other input

connections on your TV. This allows you to free up the other input connections so you can

connect more devices to your television.

��

�

��

�

��

�

��

�

��

�

��

1) Connect an S-Video Cable from the AV Receiver's MONITOR OUT, to the S-Video INPUT-1

on the back of your television.

2) Connect a Yellow Component Cable from the AV Receiver's MONITOR OUT, into the

VIDEO INPUT-1 on the back of your television.

3) Connect a Green Component Cable from the AV Receiver's Y MONITOR OUT, into the Y

VIDEO INPUT-1 on the back of your television.

4) Connect a Blue Component Cable from the AV Receiver's PB MONITOR OUT, into the

Pb VIDEO INPUT-1 on the back of your television.

5) Connect a Red Component Cable from the AV Receiver's PR MONITOR OUT, into the

Pr VIDEO INPUT-1 on the back of your television.

Notes:

• Please refer to your AV Receiver instruction manual for more information on connecting your

speakers and other devices like a DVD player.

• Use your AV Receiver's remote to switch to the different devices you have connected.

• Some AV Receivers may not respond when the V1 Smart Input function is turned on.

• If you have video connections for each input device connected to your AV Receiver, you

should not connect them using both S-Video and Composite connection at the same time

when you are using V1 Input as the V1 Smart Input. In this case we recommend using the

S-Video connection.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Plug-In Menu

Step 3 – The Interactive Plug In Menu

When you turn your television on for the first time the interactive plug-in menu will appear. The

plug-in menu helps you to get your TV ready to use by letting you set your preferences for:

• The language in which you want the onscreen menus to appear.

• Setting the TV’s clock to the correct time so your timer functions will work properly. You can

choose “AUTO” or “MANUAL” for setting the clock.

• The auto tuner setup of which channels you wish to receive.

We recommend you complete the interactive plug-in items before you start using your

television.

Language

After the “JVC INTERACTIVE PLUG IN MENU” has been displayed, the TV automatically

switches to the LANGUAGE settings. You can choose to view your onscreen menus in three

languages: English, French (Français) or Spanish (Español).

√®

To choose a language:

(English, Français or Español)

��

†

To NEXT (To set clock)

��

(To be continued...)

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Plug-In Menu

Auto Clock Set

Before you use any of your TV’s timer functions, you must first set the clock. You may precisely

set your clock using the XDS time signal broadcast by most public broadcasting stations. If you

do not have this in your area, you will have to set the clock manually. See manual clock set

below. To set the clock using the XDS signal:

√®

†

To choose AUTO

To TIME ZONE

��

√®

To select your time zone: (Atlantic, Eastern,

Central, Mountain, Pacific, Alaska or

Hawaii)

��

†

To move to D.S.T. (Daylight Savings Time)

√®

†

To turn D.S.T. ON or OFF

��

To NEXT (To Auto Tuner Setup)

��

Notes:

• The Daylight Savings Time feature automatically adjusts your TV’s clock for Daylight

Savings. The clock will move forward one hour at 2:00 am on the first Sunday in April. The

clock will move back one hour at 2:00 am on the last Sunday in October.

• You will have to reset the clock after a power interruption. You must set the clock before

operating any timer functions.

Manual Clock Set

To set your clock manually (without using the XDS signal), choose MANUAL. If you choose

AUTO, see auto clock set above.

√®

†

To choose MANUAL

To TIME

��

√®

†

To set the hour

To minute

��

√®

†

To set the minute

To Start Clock

��

Note:

• You will have to reset the clock after a power interruption. You must set the clock before

operating any timer functions.

(To be continued...)

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Plug-In Menu

Auto Tuner Setup

In auto tuner setup, the TV automatically scans through all available channels, memorizing the

active ones and skipping over blank ones or channels with weak signals. This means when you

scan (using the CHANNEL +/– buttons) you will receive only clear, active channels.

√®

To choose CABLE or AIR (or SKIP when you

skip Auto Tuner Setup)

��

†

To START

��

Programming will take approximately 1 to 2

minutes.

When the setup is finished, THANK YOU!! SETUP IS NOW COMPLETE is displayed. Your

quick setup is now complete. You can now begin watching your television, or you can continue

on in this guide for more information on programming your remote control, or using the

JVC onscreen menu system to customize your television viewing experience.

Notes:

• Noise muting will not work during Auto Tuner Setup.

• Skip appears only for interactive plug-in menu.

• The interactive plug-in menu setting does not appear if your TV has been turned on before.

In this case, use the menu to perform these settings. See pages 37, 45 and 29.

Cable Box and Satellite Users: After your auto tuner setup is complete, you may, (depending

on the type of hookup), have only 1 channel, usually 3 or 4 in the auto tuner memory. This is

normal.

The Quick Setup is complete

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Programming

Setting the CATV, VCR and DVD Codes

You can program your remote to operate your cable box, satellite receiver, VCR or DVD

player by using the instructions and codes listed below. If the equipment does not respond

to any of the codes listed below or to the code search function, use the remote control

supplied by the manufacturer.

Cable Box or Satellite Codes

The remote control is programmed with cable box and satellite codes for power on/off,

channel up/down, and 10 key operation.

1) Find the cable box or satellite brand from the list of codes shown below.

2) Slide the 2-way selector switch to “CATV”.

3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10

key pad.

4) Release the DISPLAY button, and confirm the operation of the cable box/satellite receiver.

• If your cable or satellite box does not respond to the first code, try the others listed. If it does

not respond to any code, try the search codes function, on page 25.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Programming

VCR Codes

The remote control is programmed with VCR codes for power on/off, play, stop, fast-forward,

rewind, pause, record, channel up/down operation.

1) Find the VCR brand from the list of codes shown below.

2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”.

3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10

key pad.

4) Release the DISPLAY button, and confirm the operation of the VCR.

• If your VCR does not respond to the first code, try the others listed. If it does not respond to

any of the codes, try the search codes function on page 25.

• After you program your remote, some VCR buttons may not work properly. If so, use the

VCR’s remote.

• To record, hold down the REC button on the remote and press PLAY.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Programming

DVD Codes

The remote control is programmed with DVD codes for power on/off, play, stop, fast-forward,

rewind, previous/next chapter, tray open/close, and still/pause operation.

1) Find the DVD player brand from the list of codes shown below.

2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “DVD”.

3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10

key pad.

4) Release the DISPLAY button, and confirm the operation of the DVD player.

• If your DVD player does not respond to the first code, try the others listed. If it does not

respond to any of the codes, try the search codes function on page 25.

• After you program your remote, some DVD buttons may not work properly. If so, use the

DVD player’s remote.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Programming

Search Codes

Cable/Satellite Search Codes Function

1) Slide the first 2-Way Mode Selector switch to CATV.

2) Press and hold down the POWER button, then press the RETURN+/TV button for more than

three seconds.

3) Release the RETURN+/TV button, then release the POWER button.

4) Press the POWER button on the remote, and see if the cable or satellite box responds.

5) If there was a response, press RETURN+/TV. The codes are now set. If there was no

response, repeat Step 4. If you repeat Step 4 a total of 80 times without a response, use

the remote control that came with your equipment.

6) Press RETURN+/TV to exit.

VCR/DVD Search Codes Function

1) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR” or

“DVD”.

2) Press and hold down the VCR or DVD POWER button, then press the RETURN+/TV button for

more than three seconds.

3) Release the RETURN+/TV button, then release the VCR or DVD POWER button.

4) Press the VCR or DVD POWER button, and see if the VCR or DVD responds.

5) If there was a response, press RETURN+/TV. The codes are now set. If there was no

response, repeat Step 4. If you repeat Step 4 a total of 80 times for the VCR (40 times for

the DVD player), and there is no response, use the remote control that came with your

equipment.

6) Press RETURN+/TV to exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Using the Guide

Certain symbols are used throughout this guide to help you learn about the features of your

new television. The ones you will see most frequently are:

π† Up and Down arrows mean press the CH+ or CH– buttons. Pressing the CH+ or CH–

buttons let you:

• Move vertically in a main menu screen

• Move through a submenu screen

• Move to the next letter, number, or other choice in a submenu

• Back up to correct an error

• Scan through TV channels (when not in a menu screen)

√® Left and right arrows mean press the VOLUME+ or VOLUME– buttons to move left or right

to:

• Select a highlighted menu item

• Select an item in a submenu

• Select numbers in certain menu options

• Turn the volume up or down (when not in a menu screen)

The “press button” icon means you should press the button named on your remote

control. (Button names appear in SMALL CAPITAL LETTERS.)

The “helping arrow” icon points to the highlighted or selected item in a menu.

To bring up the onscreen menu, press the MENU button on the remote control. The item that

appears in green is the one currently selected. If you use the Menu button on the TV’s front

panel instead of the remote, an additional menu screen showing INPUT will appear between

INITIAL SETUP and PICTURE ADJUST. The “interactive plug-in menu” will appear the first time

the TV is plugged in.

��

Note:

• Menus shown in this book are illustrations, not exact replications of the television’s onscreen

displays.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

The Onscreen Menu System

Your television comes with JVC’s onscreen menu system. The onscreen menus let you make

adjustments to your television’s operation simply and quickly. Examples of the onscreen

menus are shown on the next page. Detailed explanations on using each menu follow later in

this guide. For information about the interactive plug-in Menu, see pages 19 - 21.

The Onscreen Menu System

To open the onscreen menu system, press the MENU button on the remote control. You

navigate within the onscreen menus by using the four directional arrow buttons on the remote

control. (These buttons are also the CH +/– and VOL +/– buttons. Channel and volume functions

will not operate when the onscreen menu is active).

The selected feature and option on a menu screen are highlighted in a different color.

Selected Option

(Green)

��

Selected Option

(Blue)

��

To move to a different feature use the π† arrows to move up or down the list. When you

press the up arrow at the top of the list or the down arrow at the bottom, the next menu screen

will appear. Use the arrows √ ® to select an option from the highlighted feature. Pressing

MENU on the remote control will close the onscreen menu system and return you to normal

television viewing.

Each menu and its features will be discussed in the following pages of this guide.

Notes:

• If you do not press any buttons for a few seconds, the onscreen menu will automatically

shut off.

• Button names in this guide are shown in SMALL CAPITAL LETTERS.

• Menus may appear in different sizes onscreen depending on the aspect ratio selected.

• Some menu items may not appear in menu screens when certain aspect ratios or inputs

are selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Press the MENU button

��

INITIAL SETUP 04

INITIAL SETUP 03

��

Notes:

��

• The DIGITAL-IN menu

can only be displayed

when a 480p picture

signal is input to the

digital-in terminal and

the picture is being

��

INITIAL SETUP 02

PICTURE ADJUST 01

displayed on the screen.

• When the Menu button

on the TV front panel

is pressed, the FRONT

PANEL CONTROL

menu between INITIAL

SETUP 04 and

��

PICTURE ADJUST 01

will appear.

��

INITIAL SETUP 01

PICTURE ADJUST 02

��

�

��

CLOCK/TIMERS

SOUND ADJUST

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

Auto Tuner Setup

The auto tuner setup function is described on page 21 as the interactive plug-in menu. If you

need to run the auto tuner setup again, follow the steps below.

Press the MENU button

��

π†

√®

To AUTO TUNER SETUP

To operate

��

To choose CABLE or AIR

Press the OK button to start

��

Programming will take approximately 1 to 2 minutes. The auto tuner is finished when the

message PROGRAMMING OVER! appears onscreen.

Press the Menu button when finished

Channel Summary

Channel summary allows you to customize the line-up of channels received by your TV. You

can add or delete channels from the line-up or prevent any unauthorized viewers from watching

any or all 181 channels.

Press the MENU button

��

π†

To CHANNEL SUMMARY

To operate

��

√®

��

The Channel summary screen will now be displayed with

the channels set to scan marked with an “”. You can delete

channels from the scan by removing the “”. If any channels

were missed during auto tuner setup and you wish to add

them, you may by placing an “” next to the channel number.

��

π†√® To the SCAN column

Press the OK button to include or delete from scan

Press the MENU button when finished

You can block access to a channel by activating the channel lock.

Press the MENU button

π†

To CHANNEL SUMMARY

To operate

√®

π†√® To the Lock Column (

)

Press the ZERO button to lock or unlock that channel

Press the MENU button when finished

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

Channel Guard Message

When a viewer attempts to watch a guarded channel, the following message appears:

To watch a channel that you have locked, enter the

Lock Code using the 10 key pad.

If the wrong code is entered, the message

“INVALID LOCK CODE!” will flash on the screen.

��

The channel cannot be accessed until the correct code

��

is entered.

Notes:

• Once a channel has been unlocked, it will remain unlocked until the television is turned off.

• See also “Set Lock Code”, page 36.

V-Chip

Your TV is equipped with V-Chip technology which enables you to block channels or content

that you feel to be inappropriate for children, based on US and Canada rating guidelines.

V-Chip has no effect on video signals from a DVD discs, VCR tapes or Camcorder connection.

Note: Some programs, and movies are broadcast without a ratings signal. Even if you set

up V-CHIP ratings limits, these programs will not be blocked. See page 31 for information on

how to block unrated programs.

Note (for Canadian viewers): The V-Chip function is based on specifications designed for

the United States and therefore may not work properly in Canada.

You can customize the V-Chip settings of your television to match your personal tastes. The

V-Chip menu below is the starting point for your V-Chip settings

You can use US V-Chip settings (for programming broadcast from the United States), Canadian

V-Chip settings (for programming broadcast from Canada), and movie ratings. You may use

any or all of the settings (US V-Chip, Canada V-Chip, Movie ratings). Descriptions for setting

each of the three V-Chip formats appear in the next six pages along with descriptions of the

rating categories.

To access the rating categories:

Press the MENU button

��

π†

√®

To V-CHIP

To operate (Lock icon

��

will appear)

Press ZERO to access the V-Chip menu

��

√®

To turn V-Chip ON or OFF (V-Chip must be turned

ON for rating settings to operate)

π†

To move to SET US TV RATINGS,

SET MOVIE RATINGS, or

��

SET CANADIAN RATINGS (see following pages for

descriptions of each item)

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

Unrated Programs

Unrated programming refers to any programming which does not contain a rating signal.

Programming on television stations which do not broadcast rating signals will be placed in the

“Unrated Programming” category.

Examples of Unrated programs:

• Emergency Bulletins

• News

• Public Service Announcements

• Sports

• Locally Originated Programming

• Political Programs

• Religious Programs

• Weather

• Some Commercials

Note:

• TV programs or movies that do not have rating signals will be blocked if the unrated category

is set to BLOCK.

Directions to Block Unrated Programs

You can block programs that are not rated.

Press the MENU button

��

π†

To V-CHIP

��

√®

To operate (The lock icon

appears)

Press ZERO to access V-Chip setup options

��

π†

To UNRATED

√®

To VIEW or BLOCK

��

Press MENU when done

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

US V-Chip Ratings

U.S. PARENTAL RATING SYSTEMS

Programs with the following ratings are appropriate for children.

 TV Y is Appropriate for All Children

Programs are created for very young viewers and should be suitable for all ages, including

children ages 2 - 6.

 TV Y7 is for Older Children

Most parents would find such programs suitable for children 7 and above. These programs

may contain some mild fantasy violence or comedic violence, which children should be able

to discern from reality.

Programs with the following ratings are designed for the entire audience.

 TV G stands for General Audience

Most parents would find these programs suitable for all age groups. They contain little or no

violence, no strong language, and little or no sexual dialog or situations.

 TV PG Parental Guidance Suggested

May contain some, but not much, strong language, limited violence, and some suggestive

sexual dialog or situations. It is recommended that parents watch these programs first, or

with their children.

 TV 14 Parents Strongly Cautioned

Programs contain some material that may be unsuitable for children under the age of 14

including possible intense violence, sexual situations, strong coarse language, or intensely

suggestive dialog. Parents are cautioned against unattended viewing by children under 14.

 TV MA Mature Audiences Only

These programs are specifically for adults and may be unsuitable for anyone under 17

years of age. TV MA programs may have extensive V, S, L, or D.

Viewing Guidelines

In addition to the ratings categories explained above, information on specific kinds of content

are also supplied with the V-Chip rating. These types of content may also be blocked. The

content types are:

• V/FV is for VIOLENCE/FANTASY VIOLENCE

• S stands for SEXUAL CONTENT

• L stands for strong LANGUAGE

• D stands for suggestive DIALOG

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

Setting US V-Chip Ratings

Press the MENU button

��

π†

√®

To V-CHIP

To operate (lock icon

��

appears)

Press ZERO to access the V-Chip menu

��

√®

π†

√®

To turn V-Chip ON or OFF

To move to SET US TV RATINGS

To operate

��

Directions to set US V-Chip Ratings

Line up the cursor in the column (TV PG, TV G, etc.) with the content row (V/FV, S, etc.) and

press the π† or √® to move the cursor to the correct location. Press OK to turn the locking

feature on or off. An item is locked if the

icon appears instead of a “—”.

For example. To block viewing of all TV 14 shows, move the cursor to the top row of that

column and add a lock icon. Once you’ve put a lock on the top row, everything in that column

is automatically locked.

π†√® To the TV 14 Column

��

Press the OK button to lock

��

�

��

�

Press the MENU button when finished

��

�

Note:

�

• If you want to change the setup, move the cursor to the top

column and change the lock icon to “—” by pressing OK

again. You may then select individual categories to block.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

Movies Ratings

 NR – Not Rated

This is a film which has no rating. In many cases these films were imported from countries

which do not use the MPAA ratings system. Other NR films may be from amateur producers

who didn’t intend to have their film widely released.

NR (Not Rated) Programming may contain all types of programming including

children’s programming, foreign programs, or adult material.

 G – General Audience

In the opinion of the review board, these films contain nothing in the way of sexual content,

violence, or language that would be unsuitable for audiences of any age.

 PG – Parental Guidance

Parental Guidance means the movie may contain some contents such as mild violence,

some brief nudity, and strong language. The contents are not deemed intense.

 PG-13 – Parents Strongly Cautioned

Parents with children under 13 are cautioned that the content of movies with this rating may

include more explicit sexual, language, and violence content than movies rated PG.

 R – Restricted

These films contain material that is explicit in nature and is not recommended for

unsupervised children under the age of 17.

 NC-17 – No One Under 17

These movies contain content which most parents would feel is too adult for their children

to view. Content can consist of strong language, nudity, violence, and suggestive or explicit

subject matter.

 X – No One under 18

Inappropriate material for anyone under 18.

Directions to set Movie (MPAA) Ratings

Press the MENU button

π†

√®

To V-CHIP

To operate (Lock icon

appears)

Press ZERO to access V-Chip setup options

π†

√®

To SET MOVIE RATINGS

To enter movies menu

For example:

To block viewing of X and NC-17 rated from shows:

��

π†√® To the X Column

Press the OK button to lock

π†√® To the NC-17 Column

Press the OK button to lock

Press the MENU button to finish

�

_��

�

_��

��

�

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

Canadian V-Chip Ratings

 E – Exempt

Exempt programming includes: news, sports, documentaries and other information

programming, talk shows, music videos, and variety programming.

 C – Programming Intended for Children

Violence Guidelines: There will be no realistic scenes of violence. Depictions of aggressive

behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or

unrealistic in nature.

 C8+ – Programming Intended for Children 8 and Over

Violence Guidelines: Any realistic depictions of violence will be infrequent, discreet, of low

intensity and will show the consequences of the acts. There will be no offensive language,

nudity or sexual content.

 G – General Audience

Programming will contain little violence and will be sensitive to themes which could affect

younger children.

 PG – Parental Guidance

Programming intended for a general audience, but which may not be suitable for younger

children. Parents may consider some content not appropriate for children aged 8-13.

 14+ – 14 Years and Older

Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and

early teens. Programming may contain mature themes and scenes of intense violence.

 18+ – Adult

Material intended for mature audiences only.

Directions to set Canadian V-Chip Ratings

Press the MENU button

π†

√®

To V-CHIP

To operate (lock icon

appears)

Press ZERO to access V-Chip setup options

π†

√®

To SET CANADIAN RATINGS ENG (for English)

To enter ratings menu

For example:

To block viewing of programming rated 14+ and 18+:

��

√®

To the 18+ Column

Press the OK button to lock

�

��

�

√®

To the 14+ Column

Press the OK button to lock

Press the MENU button to finish

��

Note:

• For instructions on “SET CANADIAN RATINGS FRE (in French)”, please see page 35 in the

French side of this user’s guide.

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

Set Lock Code

Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes pre-

set with a lock code of “0000”. You may change the code to any four-digit number you wish. To

change the lock code, follow the steps below.

Press the MENU button

��

π†

To SET LOCK CODE

To operate (lock icon

��

√®

appears)

Press ZERO to access the lock code

The first digit will be highlighted

��

√®

π†

To select the number

��

To move to the next digit

Continue to follow these directions for all four numbers

Press the OK button to finish (your lock code is now set)

Press the Menu button when finished

When a viewer attempts to watch a blocked channel,

this message appears:

��

The channel will remain blocked until the correct lock

code is entered (see above for information on setting

your lock code).

Notes:

• After a power interruption you must reset the lock code.

• Write your lock code number down and keep it hidden from potential viewers.

• If you forget the lock code, a new code may be set using the steps listed above.

Auto Demo

This function lets you preview the many different viewing modes of your TV. It will cycle through

“Multi Screen Demo”, “Picture in Picture Demo”, all of the different “Aspect” ratios and all of the

different “Video Status” modes.

Press the MENU button

��

π† To AUTO DEMO

��

√®

To turn AUTO DEMO ON or OFF

��

Note:

��

• To stop auto demo, press the MENU button, and select auto

demo by pressing the π† buttons, and turn it off by pressing

the √® buttons. Press the MENU button to finish.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

Language

The language function is described on page 19 as the interactive plug-in menu. If you need to

choose the language again, follow the steps below.

Press the Menu button

��

π†

To LANGUAGE

��

√®

To choose a language: ENG. (English), FRAN.

(French) or ESP. (Spanish)

��

Press the MENU button when finished

��

Closed Caption

Many broadcasts now include an onscreen display of dialog called closed captions. Some

broadcasts may also include displays of additional information in text form. Your television can

access and display this information using the closed caption feature. To activate the closed

caption feature, follow the steps below.

Press the MENU button

��

π†

√®

π†

√®

To CLOSED CAPTION

To operate

��

To select CAPTION or TEXT

To select a caption (CC1 to CC4) or text channel

(T1 to T4)

��

Press the OK button to save

��

Press the MENU button when finished

Notes:

• Closed caption subtitles are usually found on closed caption channel CC1. Some programs

may include additional text information which is usually found on text channel T1. The other

channels are available for future use.

• Closed captioning may not work correctly if the signal being received is weak or if you are

playing a video tape.

• Most broadcasts containing closed captioning will display a notice at the start of the program.

• To select the mode, press the C.C. button. See page 54.

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

Auto Shut Off

This function automatically shuts off your TV when there is no signal from the channel the

TV is on.

��

Press the MENU button

��

π†

√®

To AUTO SHUT OFF

To turn ON or OFF

��

Press the MENU button when finished

��

• If the channel that you have on does not receive a

signal for more than one minute, the blinking text

“NOT RECEIVING A SIGNAL” appears on the screen, and

starts the countdown. If no signal is being received within

10 minutes, the TV shuts itself off.

��

XDS ID

XDS ID Display provides a channel’s call letters, the network’s name, and even a program

name. The XDS ID information is provided by the broadcaster.

��

Press the MENU button

��

π†

√®

To XDS ID

To turn ON or OFF

��

Press the MENU button when finished

��

Tilt Correction

This adjusts the pictures so that it looks even on the screen and not lopsided.

Press the MENU button

��

π†

√®

To TILT CORRECTION

To enter

To adjust TILT CORRECTION

��

NOTE:

��

• External Speakers: When using external speakers or

amplifiers, shut off the TV Speakers (see page 40).

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

Purity

AV-36DF74 ONLY

Sometimes, your television can be affected by the magnetic fields of the earth. If you notice

that there are sections of color on your TV screen that appear stained or blotchy, use this

function to help eliminate it.

Press the MENU button

π†

√®

To PURITY

To enter

To adjust purity

Noise Muting

This feature inserts a blank blue screen over channels which are not broadcasting or are too

weak to be received clearly.

Press the MENU button

��

π†

√®

To NOISE MUTING

To turn noise muting ON or OFF

��

Press the MENU button when finished

��

Note:

��

• Noise muting will not work during auto tuner setup or when

you operate channel summary.

Front Panel Lock

This allows you to lock the keys on the front of the TV, so that a child may not accidentally

change your viewing preferences.

��

Press the MENU button

��

π†

√®

To FRONT PANEL LOCK

To turn ON or OFF

��

Press the MENU button when finished

��

You can turn off this feature in the following ways:

��

• Unplug the power cord, and plug it back in. Do this if

your batteries die, or you lose your remote control.

• Use the remote control.

• Press the MENU button on the front of the TV for more than 3 seconds. In this case, the OSD

for FRONT PANEL LOCK will appear.

Note:

• To turn ON/OFF the TV, press the power button for more than 3 seconds. This feature will

remain ON.

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

V1 Smart Input

This feature is used if you have connected an AV Receiver to your television. By turning this

feature on, your television can automatically detect the signal source from your components

that are connected to your AV Receiver.

Press the MENU button

��

π†

√®

To V1 SMART INPUT

To turn ON or OFF

��

Press the MENU button when finished

Notes:

��

• If you do not have an AV Receiver connected to your

television, turn this feature OFF. By doing so, you can take

��

advantage of using AV CompuLink components with your television.

• Some AV Receivers may not work with this function.

TV Speaker

If your TV is connected to a stereo system, you can turn off the TV speakers and listen to the

audio through your stereo.

Press the MENU button

��

π†

√®

To TV SPEAKER

To turn the TV’s speakers ON or OFF

��

Press the MENU button when finished

��

Notes:

��

• Before you turn the TV speaker setting from OFF to ON,

make sure that the TV volume level is low! If the TV volume is set too high, the sound

level will be extremely loud.

• After a power interruption, the TV speaker settings will return to “ON”.

Audio Out

If your television is connected to an external speaker source, audio out gives you the option of

controlling the volume level with your TV’s remote control.

Press the MENU button

��

π†

To AUDIO OUT

To VARI or FIX

��

√®

��

Press the MENU button when finished

VARI: Lets you adjust the volume of the external speakers

using the VOLUME +/– buttons on your TV’s remote control.

��

FIX: The volume of the external speakers is adjusted using

the audio device’s remote control.

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

Center CH Input

When you are using a surround system, you can substitute the speaker of this television for

the center speaker of you surround system. Set CENTER CH INPUT to on when you use the

speaker as the center speaker of your surround system.

��

Press the MENU button

��

π†

√®

To CENTER CH INPUT

To adjust CENTER CH INPUT to “ON” or “OFF”

��

Press the MENU button when finished

��

Note:

The normal speaker output is 20W 16Ohms. The maximum is

40W. If you exceed the maximum, your speaker may break.

Digital-In

The DIGITAL-IN option can only be displayed in the INITIAL SETUP menu when a 480p picture

signal is being input to the DIGITAL-IN terminal. This option adjusts the position when a 480p

picture signal is being displayed on the screen. There are two types of 480p picture signals:

640x480 and 720x480. If the displayed picture is slightly shifted, the position can be adjusted

by selecting either SIZE1 or SIZE2.

Press the MENU button

��

π† To DIGITAL-IN

√® To enter

��

√® To select SIZE1 or SIZE2

Press the MENU button to finish

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Picture Adjust

Picture Settings

These settings allow you to change and adjust the way the picture appears on your television.

TINT

Tint allows you to adjust the levels of red and green in your TV picture.

COLOR

The color function lets you make all the colors in the TV picture appear either more vivid or

subtle.

PICTURE

Picture allows you to adjust the levels of black and white on the TV screen, giving you a darker

or brighter picture overall.

BRIGHT

You can adjust the overall brightness of the TV picture with the Bright control.

DETAIL

The Detail feature adjusts the level of fine detail displayed in the picture.

Adjust the Picture Settings

Press the MENU button

��

π†

To TINT, COLOR, PICTURE, BRIGHT or

DETAIL

To enter

��

√ ®

��

√ ®

π†

To adjust the setting

To move to the next setting

��

Press the MENU button when finished

Color Temperature

You can decide how strong or dull the colors appear on the TV screen.

Press the MENU button

��

π†

√®

To COLOR TEMPERATURE

To enter

��

√®

To set LOW or HIGH

��

Press the MENU button when finished

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Picture Adjust

Digital Noise Clear

With digital noise clear, this helps take our static or noise from a channel that may not be

coming in clearly.

Press the MENU button

��

π†

√®

π†

To DIG. NOISE CLEAR

To enter

To select the mode “LOW”, “HIGH” or “OFF”

��

Press the MENU button when finished

(VSM) Velocity Scan Modulation

Velocity scan modulation circuitry varies the electron beam’s horizontal scanning speed to help

accentuate the differences in picture brightness to sharpen the edges of images.

Press the MENU button

��

π†

√®

To VSM

To enter

��

√®

To turn VSM ON or OFF

��

Reset

Reset resets all picture adjustments (tint, color, picture, bright, detail, color temperature, dig.

noise clear and VSM) at once to the default settings.

Press the MENU button

��

π†

√®

To RESET

To enter

��

The onscreen menu disappears for a moment, and

then the settings are reset to the default setting for

all the picture adjustments.

��

Press the MENU button when finished

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Sound Adjust

Sound Settings

These settings allow you to change and adjust the sound on your television.

BASS – You can increase or decrease the level of low-frequency sound in the TV’s audio with

the bass adjustment.

TREBLE – Use treble to adjust the level of high-frequency sound in your TV’s audio.

BALANCE – Adjust the level of sound between the TV’s left and right speakers with the

balance setting.

Adjust the Sound Settings

Press the MENU button

��

π†

√ ®

π†

To BASS, TREBLE or BALANCE

To adjust the setting

To move to the next setting

��

Press the MENU button when finished

��

Note:

��

• You can reset the sound adjustments (BASS, TREBLE and

BALANCE) you set at once as the default setting when you select reset. See page 43.

• You can adjust BALANCE only when A.H.S. is off. See page 50.

MTS (Multi-Channel Television Sound)

MTS technology allows several audio signals to be broadcast at once, giving you a choice

in what you wish to hear with a TV program. In addition to mono or stereo sound, an

MTS broadcast may also include a second audio program (SAP).

��

Press the MENU button

��

π†

To MTS

��

√®

Select the mode

(The ON AIR arrow tells you if a broadcast is in stereo and/or

contains an SAP).

��

Press the MENU button when finished

��

Notes:

• Keep the TV in stereo mode to get the best sound quality. The sound will work in stereo

mode even if a certain broadcast is in mono sound only.

• Choose the mono setting to reduce excessive noise on a certain channel or broadcast.

• Selecting SAP will allow you to hear an alternative soundtrack, if one is available.

• MTS unavailable if your television’s input source is in input 1, 2, 3 or 4 mode, as described

on page 49.

Reset

Reset resets all Sound Adjustments (Bass, Treble and Balance) at once to the default settings.

See page 43 on how to use reset.

Download from Www.Somanuals.com. All Manuals Search And Download.

Clock/Timers

Set Clock

The set clock function is described on page 20 as the interactive plug-in menu. You can choose

to set the clock automatically, or manually. If you need to set the clock again, follow the steps

below.

Press the MENU button

π†

To SET CLOCK

To operate

√®

When you set the clock automatically, choose AUTO by pressing the

√

arrows.

π†

To TIME ZONE

��

√®

To select your time zone

��

π†

To D.S.T. (daylight savings time)

To turn D.S.T. ON or OFF

Press OK to finish

��

√®

��

Press the MENU button when finished

When you set the clock manually, choose MANUAL by pressing the

√

arrows.

π†

√®

π†

√®

To move to the hour

To set the hour

��

To move to minutes

To set the minutes

Press OK to start clock

��

Press the MENU button when finished

Download from Www.Somanuals.com. All Manuals Search And Download.

Clock/Timers

On/Off Timer

The on/off timer lets you program your television to turn itself on or off. You can use it as an

alarm to wake up, to help you remember important programs, or as a decoy when you’re not

home.

Press the MENU button

��

π†

√®

†

To ON/OFF TIMER

��

To operate (begins with ON TIME)

To set the hour (AM/PM) you want the TV to turn on

To move to minutes

��

√®

†

To set the minutes

��

To accept ON TIME and move to OFF TIME (the

time the TV will turn off). Set the OFF TIME the same way as ON TIME

To accept OFF TIME and move to CHANNEL

To select channel

†

√®

†

To ON VOLUME

√®

†

To set the volume level

To move to MODE

√®

Choose ONCE or EVERYDAY

†

To ON/OFF TIMER

√®

Choose YES to accept the timer setting, choose NO if you don’t wish to accept

Press the OK button to finish

Press the MENU button to exit the menu

Notes:

• The on/off time cannot be set to locked or guarded channels.

• In order for the on/off timer to work, the clock must be set.

• After a power interruption, the timer settings must be reset.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Multi Screen Function

PIP displays two separate pictures on screen. Your television has 2-Tuner PIP, meaning you

can view pictures from two different channels simultaneously. A special set of PIP control

buttons are located on the upper part of the remote control. Descriptions of each button

appear on this page.

Cable Box Note:

The 2–Tuner Multi Screen function may not operate when used with certain cable boxes.

This is because while some models of cable boxes may receive up to 181 channels, and

may only send the signal from one channel to your television. (Please refer to diagram on

page 12). For the 2–Tuner Multi screen function to operate correctly, it must have access

to all available channels. Since the television is receiving the signal from only one channel

from the cable box, it is impossible for the 2–Tuner Multi screen function to display a second,

different channel. Because there are many different models of cable boxes in use today,

if you are having problems operating your 2–Tuner Multi screen function feature with your

cable box, we recommend you contact your local cable company for connection advice.

PIP/Move

Turn PIP on by pressing the PIP/MOVE button

��

PIP/MOVE

Each press of PIP/MOVE will shift the PIP window to a different corner and turn off.

��

Note:

• You cannot select the component input in the PIP mode. (Except if the input is a 525i

component signal).

• When you select the AUTO TUNER SETUP, CHANNEL SUMMARY, V-CHIP, the PIP window

turns off.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Index

This allows you to quickly look at up to 9 channels at a time so that you

can decide which one to watch.

�

Notes:

• Only RF input signal will be displayed.

• You can watch the channel added in channel summary. See page 30.

Freeze

Use the FREEZE button to lock a single, still image onto the PIP window.

• If PIP is off when FREEZE is pressed, a snapshot of the main screen is taken and placed in

the PIP window.

• If PIP is on when FREEZE is pressed, the PIP window turns to blue and the image in the PIP

window will freeze.

Swap

You can exchange the channel displayed on the main screen for the one shown in the

PIP window by pressing SWAP.

Select

With SELECT, you can select the picture (channel) while viewing PIP screen. When you press

SELECT button, the channel number on the top will be highlighted. Each press of SELECT will

shift the channel.

EZ-Surf

EZ-Surf allows you to surf all the available channels so that

you don’t have to change your current program to see what

else is on TV.

Press the EZ SURF button.

• When you press the EZ SURF button, it will scan through

all the channels you can receive, and display the channel

information on the lower of the TV screen.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Power

Turns the TV on or off.

Press the POWER button

Number Buttons - 10Key Pad

Use the number buttons on the remote control to move directly to a specific channel. For

example, to move to channel 7:

0 (Zero)

7 (Seven)

100+ Button

Use the 100+ button to directly access channels above channel 99. For example, to move to

channel 124, press 100+, 2 (Two), 4 (Four).

Channel +/–

Use these buttons to move up or down all the available channels your TV is able to receive.

Volume +/–

Use these buttons to raise or lower the TV’s volume level.

Input

Selects the signal input source for the television: Input-1, 2, 3 or 4 for video devices like VCR’s

DVD players, or camcorders.

INPUT 1, 2, 3, 4

Note:

• When you return to TV mode, press the RETURN +/TV button or direct 10 key pad.

• You can also access the FRONT CONTROL PANEL screen by using the MENU button on

the front of the TV instead of the remote control. It appears between INITIAL SETUP and

PICTURE ADJUST screen, and it has INPUT menu. Choose INPUT by pressing MENU

†

the front panel and choose input by using the CHANNEL +/- buttons (

√

OPERATE

Digital-In

Use this button to directly select the digital-in input.

Press the DIGITAL-IN button

Light

Your remote control includes illuminated buttons for key features like Channel +/– and

Volume +/–. Press the light button to turn the illumination on for 5 seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Return +/TV

The return+/TV button has three functions:

Return - Returns to the channel viewed just before the channel currently onscreen.

Return+ - Lets you program a specific channel to return to while scanning through the

channels using the CH+ and CH– buttons.

TV - Returns to the TV mode.

RETURN+/TV and hold for three seconds

��

The channel currently active has been programmed as your return+ channel. Now scan

through the channels using the CHANNEL+/– buttons.

RETURN+/TV

You will return to your programmed channel.

• To cancel your return+ channel, press and hold the RETURN+ button for three seconds. The

message “RETURN CHANNEL CANCELLED!” will appear.

• Return+ works only with the Channel+/– buttons. Pressing any number key will cancel

return+.

Sound

By pressing the sound button, you can change the A.H.S. (Advanced Hyper Surround) mode

and BBE on or off.

A.H.S. - Adds a more spacious surround sound. Music gives basic effect and movie for more

effect.

BBE - BBE high definition audio adds natural, clear and extraordinary sound quality to any

program.

��

Press the SOUND button

π†

√®

To select A.H.S. or BBE

To choose the setting

��

Press the MENU when finished

Note: BBE is a registered trademark of BBE Sound, Inc. For U.S., licensed from BBE Sound,

Inc. under USP 4638258, 4482866 and 5510572. For Canada, licensed from BBE Sound,

Inc. BBE is a registered trademark of BBE Sound, Inc.

Muting

The MUTING button instantly turns the volume down completely when you press it. Press

MUTING and the volume level will instantly go to zero. To restore the volume to its previous

level, press MUTING again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Video Status

The Video status button gives you a choice of four TV picture display settings, including a

display of your own preferences.

Standard - Resets the picture display to the factory settings.

��

Dynamic - Gives a vivid picture with better contrast when viewing in

��

a brightly lit room.

Theater - Gives a rich, film-like look to video when viewing in a

dimly lit room.

Game - Used for when you are playing video games connected to

your TV.

Press the VIDEO STATUS button

By every press of the VIDEO STATUS button, you change the mode.

Note: You can also change the mode by pressing the π† buttons.

Natural Cinema

Natural cinema corrects the problem of blurred edges which may occur when viewing a

program originally shot on film (such as motion pictures) or animation. If you notice blurring

at the edges of these programs, press NATURAL CINEMA and set it to AUTO. Natural Cinema

helps correct conversion errors that occur when film, which is shot at 24 frames-per-second, is

broadcast at the television rate of 30 frames-per-second.

Press the NATURAL CINEMA button

��

Notes: The natural cinema mode "ON" is automatically set to

“AUTO” in the following cases:

��

• Turning on or off

• Changing the channel or input mode

• Using multi-screen functions

TheaterPro D6500K

The TheaterPro D6500K color temperature technology function makes sure that the video you

watch is set to the standard color temperature, so that what you see is as true to what the film

to video editors intended it to be.

Press the THEATERPRO button

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Sleep Timer

The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work in intervals

of 15 minutes, for a total time of up to 180 minutes.

Press the SLEEP TIMER button

��

Sleep Timer Message

1 minute before the automatic shutoff, this message will appear:

��

You then have 1 minute to press the SLEEP TIMER button to

delay the shut off for another 15 minutes.

Display

The display screen shows the current status of timers, inputs, and XDS ID.

Press the DISPLAY button

The screen to the right shows the following information:

��

• The current channel or AV input (Channel 05)

��

• The current time (12:20 pm)

• Sleep timer status/minutes remaining (The Sleep Timer

is off)

• On/off timer status (Set to turn on everyday at 7:00 PM,

off at 10:00 PM)

��

• Each Press of the DISPLAY button changes the display

mode:

��

Display - Full screen shown above

Time - Shows the current time only

Channel - Shows the current channel

Off - Turns display off

Notes:

• You may also turn off the display at any step by pressing MENU.

• If the clock, sleep timer or on/off timer are not set, the display screen will show:

“CLOCK NOT SET”, “SLEEP TIMER OFF”, and “ON/OFF TIMER OFF” respectively.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Aspect

This feature will help you adjust the picture you are watching to give you the best possible

picture quality.

Aspect Ratios

4:3 - Use this aspect mode when you

are watching a 4:3 broadcast.

16:9 - Use this aspect mode when you

are watching a 16:9 broadcast. This

is also referred to as "widescreen", for

example on a DVD disc. When you

select this mode, black bars will appear

on the top and bottom of the TV screen.

16:9 - If you select 16:9 aspect mode

while watching a 4:3 broadcast, this

will stretch the picture so as to fit into

the 16:9 format. When you select this

mode, black bars will appear on the top

and bottom of the TV screen.

HD ZOOM - If you are watching a 4:3

high definition broadcast and you select

this aspect mode, it will zoom in on the

picture.

V STRETCH - If you are watching a 4:3

broadcast, this aspect mode will stretch

the picture vertically on your TV

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Aspect Ratios (Continued)

Press the ASPECT button

• By pressing the ASPECT button, you can change the size.

When you change the aspect ratios, it is different from their broadcast or recorded program.

NTSC, 480i, 480p

(Including signals from the

DIGITAL-IN)

1080i, 720p

(Including signals from the

DIGITAL-IN)

��

Notes:

• You can also choose the size by pressing the π† buttons.

• When you change the aspect ratio or signal, reset the picture position to center.

C.C. (Closed Caption)

Use the C.C. (Closed Caption) button to select the mode of closed

caption.

��

Press the C.C. button

• See page 37 when you set the caption/text mode.

The MENU button allows you to access JVC’s onscreen menu system. Press MENU to activate

the onscreen menu system.

• See individual topics like “Sound Adjust” for specific information on using menus.

This button confirms your selection when you are in one of the onscreen menus.

Back

This button allows you to go back in the menu to change a selection or correct a mistake.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

TV/CATV Slide Switch

Use either the television’s own tuner or a cable box to select channels. Set this switch to TV to

operate the television’s built-in tuner. Move the switch to CATV to operate a cable box.

Note:

• See page 22 for information on programming your remote for cable box operation.

VCR/DVD Slide Switch

You can control a VCR or DVD player with the buttons on the lower part of the remote control.

Move the slide switch to VCR or DVD to operate.

Notes:

• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other

manufacturer’s brand VCR, please see the code chart and instructions on page 23.

• The remote is preset with the code 000 to control JVC-brand DVD players. For any other

manufacturer’s brand DVD player, please see the code chart and instructions on page 24.

VCR Buttons

You can use this remote control to operate the basic functions of your VCR. These functions

include: play, record, rewind, fast-forward, stop, pause, channel scan, TV/VCR, power on, and

power off.

Move the selector switch to VCR to operate.

• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other

manufacturer’s brand VCR, please see the code chart and instructions on page 23.

DVD Buttons

You can also use this remote control to operate the basic functions of your DVD player. These

functions include: play, rewind, fast-forward, stop, still/pause, previous/next, tray open/close,

power on, and power off.

Move the selector switch to DVD to operate.

• The remote is preset with the code 000 to control JVC-brand DVD players. For any other

manufacturer’s brand DVD player, please see the code chart and instructions on page 24.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Warranty

For Canadian model televisions, see the separate sheet for Canadian

Warranty information.

JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth

below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE

MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period

shown below (the “Warranty Period”) (PICTURE TUBE is covered for Two (2) years.)

Parts

Labor

1 YEAR

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE

DISTRICT OF COLUMBIA AND COMMONWEALTH OF PUERTO RICO.

WHAT WE WILL DO:

If this product is found to be defective within the warranty period, JVC will repair or

replace defective parts at no charge to the original owner. Such repair and replacement

services shall be rendered by JVC during regular business hours at JVC authorized

service centers. Parts used for replacement are warranted only for the remainder of this

Warranty Period. All products and parts thereof may be brought to a JVC authorized

service center on a carry-in basis. Televisions with a screen size of 25 inches and larger

may be covered on an in-home basis where such service is available.

WHAT YOU MUST DO FOR WARRANTY SERVICE:

To determine if in-home service is available in your area, either contact the selling dealer

(retailer) or call 1-800-537-5722 to locate the nearest JVC authorized service center. Service

locations can also be obtained from our website http://www.jvcservice.com. In-home service, if

available, will require clear access to the Television by the service representatives. If in-home

service is not available, carry in service will be provided.

If service is not locally available, box the product carefully, preferably in its original

carton, and ship, insured, with a copy of your bill of sale plus a letter of explanation of

the problem to the nearest JVC Factory Service Center, the name and location which will

be given to you by the toll free number.

If you have any questions concerning your JVC Product, please contact our Customer

Relations Department.

WHAT IS NOT COVERED:

This limited warranty provided by JVC does not cover:

1) Products which have been subject to abuse, accident, alteration, modification,

tampering, negligence, misuse, faulty installation, lack of reasonable care, or if

repaired or serviced by anyone other than a service facility authorized by JVC to

render such service, or if affixed to any attachment not provided with the products,

or if the model or serial number has been altered, tampered with, defaced or

removed;

2) Initial installation, installation and removal from “built-in” entertainment centers and

other mounting systems;

3) Operational adjustments covered in the Owner’s Manual, normal maintenance, video

and audio head cleaning;

4) Damage that occurs in shipment, due to an act of God, and cosmetic damage;

5) Signal reception problems and failures due to line power surge;

6) Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90

days from the date of purchase;

Download from Www.Somanuals.com. All Manuals Search And Download.

Warranty

7) Accessories;

8) Batteries (except that Rechargeable Batteries are covered for 90 days from date of

purchase.)

There are no express warranties except as listed above.

THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY

OF MERCHANTABILITY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY

HEREIN.

JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT,

INCONVENIENCE, OR ANY OTHER DAMAGES, WHETHER DIRECT, INCIDENTAL OR

CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES, RECORDS

OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY

BREACH OF THIS WARRANTY, ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING

THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE,

ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion of incidental or consequential damages or

limitations on how long the warranty lasts, so these exclusions or limitations may not

apply to you. This warranty gives you specific legal rights and you may also have other

rights which vary state to state.

JVC COMPANY OF AMERICA

1700 Valley Road

DIVISION OF JVC AMERICAS CORP.

Wayne, New Jersey 07470

http://www.jvcservice.com

REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY. THIS WARRANTY

DOES NOT APPLY FOR DETAILS OF REFURBISHED PRODUCT WARRANTY.

PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION

PACKAGED WITH EACH REFURBISHED PRODUCT.

For customer use:

Enter below the Model No. and Serial No. which is located either on the rear, bottom or

side of the cabinet.

Retain this information for future reference.

Model No.:

Serial No.:

Purchase Date:

Name Of Dealer:

Download from Www.Somanuals.com. All Manuals Search And Download.

Authorized Service Centers

QUALITY

SERVICE

HOW TO LOCATE YOUR JVC SERVICE CENTER

TOLL FREE: 1 (800) 537-5722

http://www.jvc.com

Dear Customer,

In order to receive the most satisfaction from your purchase, please read the instruction booklet

before operating the unit. In the event that repairs are necessary, call our Customer Relations

Department at 1-800-537-5722 or visit our website at www.JVC.com

Remember to retain your Bill of Sale for Warranty Service.

Don’t service the television yourself

Caution

To prevent electrical shock, do not open the cabinet. There are no user serviceable parts

inside. Please refer to qualified service personnel for repairs.

Accessories

To purchase accessories for your JVC product, please call toll free:1 (800) 882-2345 or on the

web at www.JVC.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

��

Specifications subject to change without notice.

JVC COMPANY OF AMERICA

Division of JVC Americas Corp.

1700 Valley Road

JVC CANADA, INC.

21 Finchdene Square

Scarborough, Ontario

Canada, M1X 1A7

Wayne, New Jersey, 07470

Download from Www.Somanuals.com. All Manuals Search And Download.

InFocus Projector DP8000 User Manual
Insignia Flat Panel Television NS 42 User Manual
Intelligent Motion Systems Switch MDriveAC User Manual
Invacare Mobility Aid F 65 User Manual
Jura Capresso Coffeemaker 13549 User Manual
JVC Flat Panel Television LT 52EM59 User Manual
Kathrein Satellite TV System UFD 540 User Manual
Kenmore Freezer 29701 User Manual
Kenwood Stereo Receiver KRC 279RA User Manual
Kenwood Stereo System KRF V5090D User Manual