JVC CRT Television AV 27150 User Manual

For models:

AV-36150

AV-36120

AV-35155

AV-32150

AV-32120

AV-32115

AV-27150

COLOR TELEVISION

USER'S GUIDE

Illustration of AV-27150 and RM-C382

IMPORTANT NOTE TO THE CUSTOMER

In the spaces below, enter the model and serial number

for your television (located at the rear of the television cabinet).

Staple your sales receipt or invoice to the inside cover of this guide.

Keep this user's guide in a convenient place for future reference.

Keep the carton and original packaging for future use.

Serial Number

Model Number

Download from Www.Somanuals.com. All Manuals Search And Download.

6 If an outside antenna is connected to the TV set, be sure the

antenna system is grounded so as to provide some protection

against voltage surges and built-up static charges. Section 810

of the National Electrical Code provides information with respect

to proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit, size

of grounding conductors, location of antenna discharge unit,

connection requirements for the grounding electrode.

13 For added protection of the TV set during a lightning storm or

when the TV set is to be left unattended for an extended peri-

od of time, unplug it from the wall outlet and disconnect the

antenna. This will prevent damage to product due to lightning

storms or power line surges.

14 A TV set and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may cause

the TV set and cart combination to overturn.

7 An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or

power circuits, or where it can fall into such power lines or

circuits. When installing an outside antenna system, extreme

care should be taken to keep from touching such power

lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL ELECTRICAL CODE

SERVICE

15 Unplug this TV set from the wall outlet and refer servicing to

qualified service personnel under the following conditions:

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the TV set.

C. If the TV set has been exposed to rain or water.

D. If the TV set does not operate normally by following the

operating instructions. Adjust only those controls that are

covered in the operating instructions as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TV set to normal operation.

8 TV sets are provided with ventilation openings in the cabinet

to allow heat generated during operation to be released.

Therefore:

E. If the TV set has been dropped or damaged in any way.

F. When the TV set exhibits a distinct change in perform-

ance — this indicates a need for service.

— Never block the bottom ventilation slots of a portable TV

set by placing it on a bed, sofa, rug, etc.

— Never place a TV set in a “built-in” enclosure unless

proper ventilation is provided.

16 Do not attempt to service this TV set yourself as opening or

removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service person-

nel.

— Never cover the openings with a cloth or other material.

— Never place the TV set near or over a radiator or heat registe.r

9 To avoid personal injury:

17 When replacement parts are required, have the service tech-

nician verify in writing that the replacement parts he uses

have the same safety characteristics as the original parts.

Use of manufacturer’s specified replacement parts can pre-

vent fire, shock, or other hazards.

— Donot placea TVset on a sloping shelf unless properly secured.

— Use only a cart or stand recommended by the TV set

manufacturer.

— Do not try to roll a cart with small casters across thresh-

olds or deep pile carpets.

18 Upon completion of any service or repairs to this TV set,

please ask the service technician to perform the safety check

described in the manufacturer’s service literature.

— Wall or shelf mounting should follow the manufacturer’s

instructions, and should use a mounting kit approved by

the manufacturer.

19 When a TV set reaches the end of its useful life, improper dis-

posal could result in a picture tube implosion. Ask a qualified

service technician to dispose of the TV set.

USE

10 Caution children about dropping or pushing objects into the TV set

through cabinet openings. Someinternal parts carry hazardous

voltages and contact can result in a fire or electrical shock.

20 Note to CATV system installer.

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that pro-

vides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of

cable entry as practical.

11 Unplug the TV set from the wall outlet before cleaning. Do

not use liquid or an aerosol cleaner.

12 Never add accessories toa TV set that has not been designed for

this purpose. Such additions may result in a hazard.

Download from Www.Somanuals.com. All Manuals Search And Download.

WELCOME!

Congratulations on your new television purchase! We thank you for choosing JVC.

We know you are anxious to start watching your new television, but before you operate it, please

read this guide and then keep it handy for future reference. After all you just bought a great TV with a lot

of terrific features, you should know what each feature is and how to use it properly!

Please note, as you read though this guide there are illustrations of select models for your

reference. There are several models covered in this guide and therefore each illustration may not be of

the specific model you own. Be sure to look for the similar feature on your TV.

Again, congratulations and thank you for choosing JVC! Enjoy!

TABLE OF CONTENTS

CONNECTIONS

Menu Functions (Continued)

Sound Settings

Connections Checklist . . . . . . . . . . . . . . . . 5

Front Panel Diagrams . . . . . . . . . . . . . . . . 5

Rear Panel Diagrams . . . . . . . . . . . . . . . . 5

Cable and VCR Connections . . . . . . . . . . . . 6

S-Video Connections . . . . . . . . . . . . . . . . 6

Connecting to a Camcorder . . . . . . . . . . . . 8

Connecting to External Amplifier . . . . . . . . . . 8

Connecting to JVC AV Compu Link

Bass . . . . . . . . . . . . . . . . . . . . 23

Treble . . . . . . . . . . . . . . . . . . . 23

Balance . . . . . . . . . . . . . . . . . . 23

MTS (Multi-channel TV Sound) . . . . . . . 23

Some Sound Advice . . . . . . . . . . . . 23

General Items

On/Off Timer . . . . . . . . . . . . . . . . 24

TV Speaker . . . . . . . . . . . . . . . . 25

Audio Out . . . . . . . . . . . . . . . . . 25

Closed Caption . . . . . . . . . . . . . . 25

Capable Components . . . . . . . . . . . . 9

GETTING STARTED

Remote Controls . . . . . . . . . . . . . . . . . . 10

Power . . . . . . . . . . . . . . . . . . . . . . . . 11

Adjusting Volume . . . . . . . . . . . . . . . . . . 11

Changing Channels . . . . . . . . . . . . . . . . 11

Remote Programming . . . . . . . . . . . . . . . 12

CATV & Satellite Codes . . . . . . . . . . . . . . . 12

VCR Codes . . . . . . . . . . . . . . . . . . . . . 13

BUTTON FUNCTIONS

Menu. . . . . . . . . . . . . . . . . . . . . . . . 26

Exit. . . . . . . . . . . . . . . . . . . . . . . . 26

Display . . . . . . . . . . . . . . . . . . . . . . . 26

Video Status . . . . . . . . . . . . . . . . . . . . 26

Sleep Timer . . . . . . . . . . . . . . . . . . . . . 26

Input. . . . . . . . . . . . . . . . . . . . . . . . . 26

Hyper Surround . . . . . . . . . . . . . . . . . . . 27

Muting. . . . . . . . . . . . . . . . . . . . . . . . 27

Number Buttons - 10 Key Pad . . . . . . . . . . . 27

100+ . . . . . . . . . . . . . . . . . . . . . . . . 27

Return+ . . . . . . . . . . . . . . . . . . . . . . . 27

VCR Buttons . . . . . . . . . . . . . . . . . . . . 27

PIP (Picture-In-Picture)

MENU FUNCTIONS

Using the Menu . . . . . . . . . . . . . . . . . . . 14

Plug In Menu

Introduction. . . . . . . . . . . . . . . . . 15

Language. . . . . . . . . . . . . . . . . . 15

Auto Tuner Setup. . . . . . . . . . . . . . 15

Set Clock . . . . . . . . . . . . . . . . . . 16

Auto (XDS). . . . . . . . . . . . . . . . 16

Manual. . . . . . . . . . . . . . . . . . 16

Finish. . . . . . . . . . . . . . . . . . . . 16

Channel Summary. . . . . . . . . . . . . . . . . . 17

V-Chip. . . . . . . . . . . . . . . . . . . . . . . . 18

Set Lock Code. . . . . . . . . . . . . . . 21

Picture Settings

Introduction . . . . . . . . . . . . . . . . 28

On/Move . . . . . . . . . . . . . . . . . . 28

Freeze . . . . . . . . . . . . . . . . . . . 28

Swap . . . . . . . . . . . . . . . . . . . . 28

Channel +/- . . . . . . . . . . . . . . . . 28

Source. . . . . . . . . . . . . . . . . . . 28

APPENDICES

Tint . . . . . . . . . . . . . . . . . . . . . 22

Color . . . . . . . . . . . . . . . . . . . . 22

Picture . . . . . . . . . . . . . . . . . . . 22

Bright . . . . . . . . . . . . . . . . . . . 22

Detail . . . . . . . . . . . . . . . . . . . . 22

Noise Muting . . . . . . . . . . . . . . . . 22

Set Video Status . . . . . . . . . . . . . . 22

Troubleshooting . . . . . . . . . . . . . . . . . . 29

Limited Warranty . . . . . . . . . . . . . . . . . 30

Authorized Service Centers . . . . . . . . . . . . 31

Specifications . . . . . . . . . . . . . . Back Cover

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections 5

CONNECTIONS CHECKLIST - READ ME FIRST

The Connections Checklist section of this guide is a list of ideas to keep in mind while you setup your

new TV. It is designed to help us not-so-technically-minded individuals make our connections properly.

If you read this section and still can’t identify the plugs, connectors and components you have, please

ask someone for help in making your connections.

1) Always refer to the connection instructions in the

user’s guide for your components first. The

manufacturer will provide the most detailed

information about their products.

2) Know your jacks and plugs - most are color coded:

A/V Input Plug

• Yellow plugs are Video connections

• Red plugs are Right Audio connections

• White (or black) plugs are Left Audio (or Mono)

connections. If your VCR is mono-sound, it will have

only a white or black plug, no second red one.

3) Perform one connection at a time. If you have

RF Connectors

several accessories to connect, make sure each

connection is correct by checking to see that it works

properly before trying the next connection.

4) Unplug the power cord during each connection.

5) Follow the In and Out Concept. Remember In and

S-Video Plug

Out - the Output jack from one device will go to the

Input jack of the other. Read the jack panels, they are

all labeled.

6) The AV Compu Link Cable lets you connect to

certain JVC devices. If you have a JVC Compu Link

VCR or other piece of equipment, but don’t have an

AV Compu Link cable, contact your local JVC dealer.

AV Compu Link Cable

Front/Rear Panel Diagrams

Rear Panel - All models except AV-32115

Rear Panel - AV-32115 Only

Front Panel - AV-36150, AV-36120

Front Panel - All 32 and 27 inch models

and AV-35115

Download from Www.Somanuals.com. All Manuals Search And Download.

6 Connections

Cable and VCR Connections

There are three basic types of antenna or cable connections:

• If you have an antenna or have a cable system that does not require the use of a cable box to

select channels, please refer to Diagram #1.

• If you have a cable system that requires the use of a cable box to access all the channels, please

refer to Diagram #2.

• If you have a cable system that requires the use of a cable box to access certain premium channels,

but not “basic” cable channels, please refer to Diagram #3.

• For instructions on connecting a VCR only, please see the Quick Setup Guide.

• For instructions on using Picture In Picture (PIP), please see page 28.

Illustration of AV-32150

1) Connect the antenna or cable TV wire from the wall outlet, in to the RF Input of the two-way splitter.

2) Connect an RF cable from the one of the RF Outputs on the splitter, in to the RF Input on the back of the VCR.

3) Connect an RF cable from the other the RF Output on the splitter, in to the RF Input on the back of the TV.

4) Connect the yellow video cable out from the VCR’s Video Output, in to the TV’s Video Input jack.

5) Connect the white audio cable out from the VCR’s Left Audio Output, in to the TV’s Left Audio Input Jack.

6) Connect the red audio cable out from the VCR’s Right Audio Output, in to the TV’s Right Audio Input jack.

• If your VCR is a mono sound unit, it will have only one Audio Out jack. Connect it to the TV’s Left Audio Input.

• Please consult your VCR’s owner’s manual for more information on its operation.

S-Video Connections

You may also choose to connect video devices (VCR, Camcorders, etc) by using an S-Video Cable. S-Video

may be substituted in any of the connections diagrams included here. To use S-Video:

1) Plug an S-Video cable out from the video device and in to the TV’s S-Video Input.

Keep the audio connections the same as shown in the diagrams.

• AV-32115 has no S-Video input.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections 7

Audio/Video Connections — Continued

Illustration of AV-32150

1) Connect the antenna or cable TV wire from the wall outlet, in to the RF Input of the cable box.

2) Connect an RF cable from the cable box RF Output, in to the RF Input on the back of the VCR.

3) Connect an RF cable from the RF Output on the VCR, in to the RF Input on the back of the TV.

4) Connect the yellow video cable out from the VCR’s Video Output, in to the TV’s Video Input jack.

5) Connect the white audio cable out from the VCR’s Left Audio Output, in to the TV’s Left Audio Input Jack.

6) Connect the red audio cable out from the VCR’s Right Audio Output, in to the TV’s Right Audio Input jack.

Illustration of AV-32150

1) Connect the antenna or cable TV wire from the wall outlet, in to the RF Input of the two-way splitter.

2) Connect an RF cable from the one of the RF Outputs on the splitter, in to the cable box RF Input.

3) Connect an RF cable from the Cable Box Output, in to the VCR RF Input.

4) Connect an RF cable from the other the RF Output on the splitter, in to the RF Input on the back of the TV.

5) Connect the yellow video cable out from the VCR’s Video Output, in to the TV’s Video Input jack.

6) Connect the white audio cable out from the VCR’s Left Audio Output, in to the TV’s Left Audio Input Jack.

7) Connect the red audio cable out from the VCR’s Right Audio Output, in to the TV’s Right Audio Input jack.

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Connections

Connecting to a Camcorder

Illustration of AV-32150

1) Connect the white audio cable from the Camcorder’s Left Audio Output jack to the TV’s Left Audio Input jack.

2) If you have a stereo Camcorder, connect the red audio cable from the Camcorder’s Right Audio Output

jack to the TV’s Right Audio Input jack.

3) Connect a yellow video cable from the Camcorder’s Video Output to the TV’s Video Input jack.

Connecting to an External Amplifier

Illustration of AV-32150

1) Connect the white audio cable from the TV’s Left Audio Output jack to the Amplifier’s Left Audio Input jack.

2) Connect the red audio cable from the TV’s Right Audio Output jack to the Amplifier’s Right Audio Input jack.

•

See also ‘TV Speaker’ and ‘Audio Out’ on page 25 for more information on using external speakers.

Function not available on model AV-32115.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections 9

Connecting to JVC AV Compu Link Capable Components

(All models except AV-32115)

JVC’s AV Compu Link feature makes playing video tapes totally automatic. Simply insert a pre-recorded

tape* into your JVC-brand VCR and the VCR will automatically turn on and begin playback. At the same

time, using the AV Compu Link, the VCR sends a signal to the television telling it to turn on and switch

to the proper video input to watch a video tape.

• The AV Compu Link cable may be included with the JVC AV Compu Link accessory you wish to

connect. If it is not, contact an authorized JVC Service Center for part # EWP 805-012.

• AV Compu Link can only be used with JVC-brand products.

Illustration of AV-32150

To Connect: Plug one end of the AV Compu Link cable into the AV Compu Link input on your VCR or

other Compu Link device. Plug the other end of the AV Compu Link cable into the AV Compu Link input

at the rear of the television.

NOTES:

* In order for the VCR playback to begin automatically, the recording tabs must be removed from the VHS tape. If the tab is

in place, automatic switching will occur when you push the VCR’s PLAY button.

• The AV Compu Link cable has a male 3.5 mm (mono) plug on each end.

• If your JVC-brand VCR has “A Code/B Code Remote Control Switching” (see your VCR’s instruction book), using VCR A

Code will switch the TV to Video Input 1. If you use Input 1 for video input from your cable box, use VCR B Code to select

the TV Video Input 2.

• To connect a JVC HiFi receiver or amplifier for a completely automated home theater, see the HiFi’s connection

instructions for detailed connection information.

• AV COMPU LINK EX is compatible with the following receivers: RX-664V, RX-665V, RX-668VBK, RX-774V, RX-788VBK,

RX-884V, RX-888VBK, RX-1024V, RX-1028VBK, and later receiver models.

Download from Www.Somanuals.com. All Manuals Search And Download.

10 Getting Started

REMOTE CONTROLS

RM-C382

AV-36150 • AV-35115

RM-C381

AV-36120 • AV-32120

RM-C205

AV-32115

AV-32150 • AV-27150

Changing the Batteries

Be sure to use only size AA batteries.

Raise the latch on the remotes’ back cover or

push down on the back cover and slide

towards the bottom to remove it.

Insert two AA batteries (supplied), carefully

noting the "+" and "-" markings on the

batteries and on the remote control. To avoid

a potential short circuit, insert the "-" end first.

RM-C382

RM-C381

When batteries are installed, snap the back

cover into place.

• If the remote control acts erratically, replace the

batteries. Typical battery life is six months to one

year.

• We recommend using alkaline batteries for

longer battery life.

When you change the batteries, try to complete the

task within three minutes. If you take longer than three

minutes, the remote control codes for your VCR

and/or Cable Box may have to be reset (page 12-13).

RM-C205

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Started 11

POWER

• Press the POWER button on the remote control or the front panel of the TV. The ON TIMER lamp will glow red.

• Make sure the TV/CATV switch on the remote is set to TV (RM-C381 and RM-C382 only). Move the switch to

CATVonly if you plan to operate a cable box. On the CATV setting the remote will only operate the cable box

functions.

• To turn the power off, press the Power button again. The ON TIMER lamp will go out.

• The ON TIMER lamp will glow red when the On/Off Timer is set (page 24), even when the TV power is off.

ADJUSTING VOLUME

To control the volume level, use the VOLUME+/- buttonson the remote control or on the TV's front panel. Use

the VOLUME - button to lower the volume. Press the VOLUME+ button to raise the volume.

VOLUME 13

|||||||

-------------------

Press the MUTING button to instantly turn the volume to zero. Press MUTING again to return to the previous

volume level.

CHANGING CHANNELS

10 key direct access

To move directly to a specific channel, press that channel's numbers on the remote's 10 key pad. For single-digit

channel numbers, press "0" then the channel number. For channels above 100, press the 100+ button, then the

remaining two digits on the 10 key pad.

CHANNEL -/+ BUTTON

To scan through the channels, press either the CHANNEL+ or CHANNEL- button. You will move through the

channels in numerical order.

• After you operate the Auto Tuner Setup (page 15), all of the empty channels will be removed from scanning.

When you scan you will only receive clear, active channels.

Hyperscan

With JVC's Hyperscan feature you can zip through the channels at a rate of five per second. To use Hyperscan,

press and hold either the CHANNEL+ or CHANNEL- buttons. After the first few channels scan at normal speed, the

rest will move by at five per second. To scan at normal speed, press and release the CHANNEL+/- button.

Regular Return

Press and release the RETURN+ button to return to the previous channel viewed. For example, select a channel,

then select another channel using the 10 key pad buttons. You can now flip back and forth between these two

channels by pressing RETURN+.

RETURN+

With RETURN+ You can program your TV to always return to a specific channel. Press and hold down the RETURN+

button for three seconds. The message, "RETURN CHANNEL PROGRAMMED!" will appear on-screen. Now

when you scan through the channels, pressing RETURN+ will bring you back to your programmed channel.

To cancel the RETURN+ channel, press and hold the RETURN+ button for three seconds. The message "RETURN

CHANNEL CANCELLED!" will appear on-screen.

• Pressing any number key or turning off the TV will also cancel the RETURN+ channel.

Download from Www.Somanuals.com. All Manuals Search And Download.

12 Remote Programming

Setting the CATV & VCR Codes

You can program your remote to operate your cable box or satellite receiver by using the instructions

and codes listed below. If the equipment does not respond to any of the codes listed below or to the

code search function, use the remote control supplied by the manufacturer.

Cable Box or Satellite setup (All models except AV-32115)

The remote control is programmed with CATV and/or Satellite codes for power on, power off, channel up,

channel down, and 10 key operation.

1) Find the CATV/Satellite brand from the list of codes shown below.

2) Slide the 2-way selector switch to “CATV”.

3) Press and hold down the DISPLAY button.

4) With the DISPLAY button held down, enter the first code number listed using the 10 key pad.

5) Release the DISPLAY button.

6) Confirm the operation of the Cable Box/Satellite receiver.

• If your CATV or Satellite box does not respond to the first code, try the others listed. If it does not

respond to any code, try the Search Codes Function at the bottom of the page.

CABLE BOXES

CODES

DIGITAL

SATELLITE

SYSTEMS

CODES

CABLE BOXES

CODES

Puser

RCA

Realistic

Regal

032

061, 070

032

ABC

024

Archer

Cableview

Citizen

Curtis

Diamond

Eagle

Eastern

GCBrand

Gemini

032, 025

051, 032

022, 051

058, 059

100

106

112

104, 111

104

105

102, 103

108

Echostar

G.E.

058, 064, 040, 041, 042, 045,

068

034

Gradiente

Hitachi

HNS(Hughes)

Panasonic

Philips

Primestar

RCA

Sony

Regency

Rembrandt

Samsung

Scientific Atlanta 057, 058, 059

SLMark

Sprucer

Stargate

Telecaption

Teleview

Texscan

Tocom

Toshiba

Unika

Universal

Videoway

Viewstar

Zenith

024, 032, 025

029

037, 032, 051, 038

051

034

032, 051

022, 043

051, 047

051, 056

032, 051

067

047, 051

044

106, 109, 110

107

General Instrument 065, 024, 025, 026, 027, 020,

021, 022, 057, 023

Hamlin

Hitachi

Jerrold

101

102, 103

040, 041, 042, 045

Toshiba

Uniden

049, 024

065, 024, 025, 026, 027, 020,

021, 022, 057, 023

049, 050, 051, 054

035, 036, 066

050

Macom

032, 025

022, 032

052

029, 030

063, 046

046

Magnavox

Memorex

Movietime

Oak

Panasonic

Paragon

Philips

033

030

032, 051

039, 037, 048

055, 056, 060

Zenith/Drake

Satellite

063

028, 029, 030, 052, 053, 031,

069

Pioneer

Pulsar

047, 062

051, 032

Search Codes Function:

1) Slide the 2-Way Mode Selector switch to CATV.

2) Press the TV POWER and RETURN+ buttons. Hold for at least three seconds and release.

3) Press TV POWER, see if the CATV or Satellite box responds.

4) If there was a response, press RETURN+. The operating codes are now set. If there was no response,

repeat Step 3. If you repeat Step 3 64 times without a response, use the remote control which came

with the equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Programming 13

VCR setup

The remote control is programmed with VCR codes for power on, power off, play, stop, fast-forward, rewind,

channel up, and channel down operation.

1) Find the VCR brand from the list of codes shown below.

2) Slide the 2-way selector switch to “TV”.

3) Press and hold down the DISPLAY button.

4) With the DISPLAY button held down, enter the first code number listed with the 10 key pad.

5) Release the DISPLAY button.

6) Confirm the operation of the VCR.

• If your VCR does not respond to the first code, try the others listed. If it does not respond to any code, try

the Search Codes Function at the bottom of the page.

• To record, hold down the REC button on the remote and press PLAY.

• Some menufacturer’s VCR’s may not respond to the TV/VCR button, even if other buttons work properly.

• AV-32115 Users: The model RM-C205 remote control can only be used with JVC-brand VCR’s

VCRs

Admiral

Aiwa

Akai

CODES

VCRs

Magnavox

Marantz

Marta

Memorex

MGA

Minolta

Mitsubishi

CODES

VCRs

Samsung

Sansui

Sanyo

Scott

CODES

035

027, 032

031, 023, 024, 086

003, 004, 005

037, 060, 062, 033, 089

003, 026, 020, 052

063, 067, 091, 071

059, 060, 062, 067, 038, 040,

047, 048, 026, 020

063, 064, 065, 066, 058, 000,

001

029, 072, 073, 074

064

024, 067

Audio Dynamic 003, 005

Bell &Howell

Broksonic

Canon

CCE

Citizen

063, 071

020, 026

023, 025

043

038, 040, 047, 048, 041, 042

058, 045

038, 040, 047, 048, 041, 042,

078, 090

047, 027, 062

003, 004, 005, 000

024, 023

028, 021, 035, 064

026, 020

023, 024, 021, 022

024, 058, 045, 063, 003, 004,

005, 093

Sears

Shintom

Sharp

Signature 2000

Singer

075

064

Multitech

NEC

Olympic

Optimus

Orion

035, 036, 080, 088

027, 035

Craig

063, 029, 064

045, 024, 027, 093

043, 059, 024, 092

003, 004, 005

045

Curtis Mathes

Daewoo

DBX

Dimensia

Emerson

075

Sony

028, 029, 030, 053, 054, 055

027

031, 023, 024, 027

027, 081

SV2000

Sylvania

Symphonic

Tashiro

Panasonic

Penney

043, 026, 077, 061, 025, 042,

020, 076

064

Fisher

Funai

Go Video

Goldstar

Gradiente

Hitachi

Instant Replay

Jensen

JVC

063, 066, 067, 065, 071

027, 026, 020, 000

033, 045, 024, 093

037, 051, 049, 050, 089

064

083, 084, 081, 000, 001

023, 045, 058, 027, 081, 093

024, 023

Pentax

Philco

058, 005, 045, 093

031, 024, 027, 023, 026, 020,

043

031, 023, 024, 086

023

045, 058, 023, 024, 031, 046,

059, 060, 033, 087, 093

021, 022, 023, 024

033, 024, 063, 036, 067, 040,

027

033, 045, 058, 023, 024, 031,

046, 059, 060, 083, 085, 087,

093

Tatung

Teac

Technics

Teknika

Toshiba

003, 004, 005

003, 004, 027, 005

021, 022, 023, 024

024, 027, 070

Philips

Pioneer

Proscan

059, 046, 079

Vector Research 005

Wards

Yamaha

Zenith

035, 036, 067, 044, 064

063, 003, 004, 005

044, 082, 064

Quasar

Radio Shack

003

000, 001, 002, 003, 004, 005

003, 004, 064, 005

027, 064, 058, 065, 066, 063,

067

Kenwood

LXI

RCA

Realistic

024, 063, 036, 067, 040, 027

Search Codes Function:

1) Slide the 2-Way Mode Selector switch to TV.

2) Press the VCR POWER and RETURN+ buttons. Hold for at least three seconds and release.

3) Press VCR POWER, see if the VCR responds.

4) If there was a response, press RETURN+. The operating codes are now set. If there was no response,

repeat Step 3. If you repeat Step 3 74 times without a response, use the manufacturers remote control

which came with the VCR.

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Using the Menu

Picture Settings

Using this Guide

PICTURE ADJUST

Certain symbols are used throughout this guide to help you learn

about the features of your new television. The ones you will see

most frequently are:

TINT

-------------------------

COLOR

PICTURE

BRIGHT

DETAIL

Up and Down arrows mean press the CHANNELUP or CHANNEL

DOWN buttons. Pressing the UP or DOWN buttons let you:

-------------------------

• Move vertically in a main menu screen

• Move through a submenu screen

• Move to the next letter, number, or other choice in a submenu

• Back up to correct an error

SELECT

OPERATE

EXIT BY

• Scan through TV channels (when not in a menu screen)

PICTURE ADJUST

Left and right arrows mean press the VOLUME LEFT or VOLUME

RIGHT buttons to:

• Select a highlighted menu item

NOISE MUTING

SET VIDEO STATUS

ON OFF

• Select an item in a submenu

• Select numbers in certain menu options

• Turn the volume up or down (when not in a menu screen)

The "Press Button" icon means you should press the button

named on your remote control. (Button names appear in SMALL

CAPITALLETTERS.)

SELECT

OPERATE

EXIT BY

Sound Settings

SOUND ADJUST

The ‘Helping Hand’ points to the highlighted or selected item in

a menu.

The Onscreen Menus:

BASS

-------------------------

To bring up the onscreen menu, press the MENU button on the

remote control. The item that appears in yellow is the one currently

selected.

TREBLE

BALANCE

MTS

-------------------------

STEREO SAP MONO

ON AIR

The “Plug In Menu’ will appear the first time the TV is plugged in.

If you use the Menu button on the TV’s front panel instead of the

remote, an additional menu screen showing channel number and

input will appear between menu 1 and 2.

SELECT

OPERATE

EXIT BY

Note: Menus shown in this book are illustrations, not exact

General Items

replications of the television’s onscreen displays.

CLOCK/ TIMERS

PLUG IN MENU

LANGUAGE

AUTO TUNER SETUP

SET CLOCK

ENG FRE SPA

SET CLOCK

ON/ OFF TIMER

FINISH

SELECT

OPERATE

EXIT BY

SELECT

OPERATE

Initial Setup Items

EXIT BY

INITIAL SETUP

AUTO TUNER SETUP

CHANNEL SUMMARY

V-CHIP

TV SPEAKER

AUDIO OUT

LANGUAGE

ON OFF

VARI FIX

ENG FRE SPA

SET LOCK CODE

CLOSED CAPTION

SELECT

OPERATE

SELECT

OPERATE

EXIT BY

Download from Www.Somanuals.com. All Manuals Search And Download.

Plug In Menu 15

Introduction

Auto Tuner Setup

The Plug In Menu comes up automatically when

you first turn on the TV after plugging it in. The

Plug In Menu helps you to get your TV ready to

use by letting you set your preferences for:

In Auto Tuner Setup, the TV automatically scans

through all available channels, memorizing the active

ones and skipping over blank ones or channels with

weak signals. This means when you scan (using the

CHANNEL+/- buttons)you will receive only clear,

active channels.

• The Language in which you want the on screen

menus to appear,

Press the MENU button

To AUTO TUNER SETUP

To operate

• The Auto Tuner Setup of which channels you

wish to receive,

• Setting the TV’s clock to the correct time so

your timer functions will work properly.

TUNER MODE

CABLE

AIR

Descriptions of each of the Plug In Menu features

appear on this page and the next. We recommend

you complete the Plug In Menu setup first so your

TV is set up just the way you want right away.

START

To choose CABLE or AIR

To move to START

Language

You can choose to view your onscreen menus in

three languages: English, French or Spanish.

To start Auto Tuner Setup

NOW

PROGRAMMING !

Press the MENU button

To LANGUAGE

LANGUAGE

ENG FRE SPA

To choose a language

EXIT when finished

Programming will take approximately 1 to 2

minutes.

PROGRAMMING OVER!

• Noise Muting will not work during Auto Tuner

Setup.

NOTES:

If you exit the Plug In Menu, or wish to change your preferences later, all the Plug In Menu options can be found in the

regular on screen menus.

Download from Www.Somanuals.com. All Manuals Search And Download.

16 Plug In Menu

Set Clock

Set Clock - Manual

To set your clock manually (without using the XDS

signal), choose MANUAL from the Set Clock menu

and follow the steps below.

Before you use any of your TV’s timer functions,

you must first set the clock. You may precisely set

your clock using the XDS time signal broadcast

by most Public Broadcasting stations. To set the

clock using the XDS signal:

MODE

TIME

AUTO MANUAL

--:-- --

Enter the channel number of your local PBS

station.

Press MENU

To Set Clock

To operate

START CLOCK

To move to the hour

To AUTO

To set the hour

MODE

AUTO MANUAL

To move to minutes

To set the minutes

TIME ZONE

D.S.T.

EASTERN

To move to START CLOCK

To start clock and exit

ON OFF

FINISH

THANK YOU !!

To TIME ZONE

To select your time zone

Finish

Once you have the items in the Plug In Menu set

to your personal preferences, move to the Finish

option to save your settings.

To move to Daylight Savings Time (D.S.T.)

To turn D.S.T. ON or OFF

To FINISH

To save settings and exit

• You can change the preferences you set in the

Plug In Menu at any time using the regular JVC on

screen menu system.

• If you do not have a PBS station in your local

area, you will have to set the clock manually. See

‘Set Clock - Manual’ at the top of the next column

for instructions.

• The Daylight Savings Time feature automatically

adjusts your TV’s clock for Daylight Savings. The

clock will move forward one hour at 2:00 am on

the first Sunday in April. The clock will move back

one hour at 2:00 am on the last Sunday in

October.

NOTES:

• Auto Clock Set is not available on model AV-32115.

• You will have to reset the clock after a power interruption of 90 seconds or longer.

• You must set the clock before operating any timer functions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Functions 17

Channel Summary

Channel Summary - Lock

Channel Summary allows you to customize the

line-up of channels received by your TV. You can

add or delete channels from the line-up or

prevent any unauthorized viewers from watching

any or all 181 channels.

To CHANNEL SUMMARY

To operate

CHNO. SCAN

CHNO.

SCAN

Press the MENU button

To CHANNEL SUMMARY

To operate

The Channel Summary screen (below) will now

be displayed with the channels set to scan

marked with an "ü". You can delete channels from

the scan by removing the "ü". If any channels

were missed during Auto Tuner Setup and you

wish to add them, you may by placing an "ü" next

to the channel number.

To the Lock Column

ZERO to lock or unlock that channel

EXIT when finished

Channel Guard Message

When a viewer attempts to watch a guarded channel,

the following message appears:

CHNO. SCAN

THIS CHANNEL IS LOCKED BY

CHANNEL GUARD.

PLEASE ENTER LOCK CODE BY

10 KEY PAD TO UNLOCK IT.

To the SCAN column

NO. - - - -

To include or delete from scan

EXIT when finished

To watch a channel that you have locked, enter the

Lock Code using the 10 key pad (see “Set Lock

Code” - page 21).

If the wrong code is entered, this message will flash

on the screen:

INVALID LOCK CODE !

The channel cannot be accessed until the correct

code is entered.

• Once a channel has been unlocked, it will

remain unlocked until the television is turned off.

NOTES:

Some cable systems experience interference from radio frequencies on cable Channel 95. You may delete this channel

from your scan by removing the "ü" next to it on the Channel Summary screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

18 V-Chip

U.S. PARENTAL RATING SYSTEMS

Programs with the following Ratings

are appropriate for Children.

V-Chip

Your TV is equipped with V-Chip technology which

enables TV Parental Guideline and Movie (MPAA)

Guideline controls. V-Chip technology allows you to

program your TV to receive, or not to receive,

programs based on content according to the

guidelines. Programs which exceed the ratings limits

you set will be blocked.

❒ TVY is Appropriate for All Children.

Programs are created for very young viewers

and should be suitable for all ages, including

children ages 2 - 6.

❒ TV Y7 is for Older Children.

When a viewer attempts to watch a blocked channel,

this message appears:

Most parents would find such programs

suitable for children 7 and above. They may

contain some mild fantasy violence or

comedic violence, which children should be

able to discern from reality.

THIS PROGRAMMING EXCEEDS

YOUR RATING LIMITS.

PLEASE ENTER LOCK CODE BY

10 KEY PAD TO UNLOCK IT.

NO. - - - -

Programs with the following Ratings

are designed for the entire audience.

To watch a blocked channel, enter the lock code

(page 21) using the 10 key pad.

❒ TV G stands for General Audience.

Most parents would find these programs

suitable for all age groups. They contain little

or no violence, no strong language, and little

or no sexual dialog or situations.

❒ TV PG Parental Guidance Suggested.

May contain some, but not much, strong

language, limited violence, and some

suggestive sexual dialog or situations. It is

recommended that parents watch these

programs first, or with their children.

❒ TV 14 Parents Strongly Cautioned.

Programs contain some material that may be

unsuitable for children under the age of 14

including possible intense violence, sexual

situations, strong coarse language, or

intensely suggestive dialog. Parents are

cautioned against unattended viewing by

children under 14.

To set up the TV Parental Guideline

Ratings:

Press the MENU button

To V-CHIP

To operate (Lock icon

will appear)

Press ZERO to access the V-Chip menu

V-CHIP

ON OFF

SET US TV RATINGS

SET MOVIE RATINGS

UNRATED VIEW BLOCK

FINISH

To turn V-Chip ON or OFF

To move to SET US TV RATINGS

To Operate (see page 19 for details)

❒ TV MA Mature Audiences Only.

These programs are specifically for adults

and may be unsuitable for anyone under 17

years of age. TV MA programs may have

extensive V, S, L, or D.

TV TV TV TV TV TV

— — — — — —

V/ FV — — —

—

— — —

— —

FINISH

Viewing Guidelines

• V/FV is for VIOLENCE/FANTASY VIOLENCE

• S stands for SEXUAL CONTENT

• L stands for strong LANGUAGE

• D stands for suggestive DIALOG

Download from Www.Somanuals.com. All Manuals Search And Download.

V-Chip 19

Directions to Block Viewing:

Directions to set up Movie Ratings:

Line up the cursor in the column (TV PG, TV G,

etc.) with the content row (V/FV, S, etc.) and press

the or to move the cursor to the correct

Press the MENU button

To V-CHIP

location. Press or to turn the locking feature

To operate (Lock icon

appears)

on or off. An item is locked if the

appears instead of a “—”.

icon

Press ZERO to access V-Chip setup

options

To SET MOVIE RATINGS

For example. To block viewing of all TV 14

To enter movies menu

shows:

Move the cursor to the top row of that column

and add a lock icon. Once you've put a lock on

the top row, everything in that column is

automatically locked.

—

^N17 R ^P13 PG G NR

C- G-

— — — — — —

FINISH

To the TV 14 Column

To turn on the lock

❒ NR - Not Rated.

This is a film which has no rating. In many

cases these films were imported from countries

which do not use the MPAA ratings system.

Other NR films may be from amateur producers

who didn’t intend to have their film widely

released.

NR (Not Rated) Programming may contain

all types of programming including

children's programming, foreign programs,

or adult material.

TV TV TV TV TV TV

—

— — — —

V/ FV —

—

FINISH

To FINISH

To save settings and exit

❒ G – General Audience.

• If you want to change the setup, move the

cursor to the top column and change the lock

icon to "—". You may then select individual

categories to block.

In the opinion of the review board, these

films contain nothing in the way of sexual

content, violence, or language that would be

unsuitable for audiences of any age.

❒ PG – Parental Guidance.

Special Note about Ratings

Parental Guidance means the movie may

contain some contents such as mild violence,

some brief nudity, and strong language. The

contents are not deemed intense.

Some programs are not broadcast with a

ratings signal. Therefore, even if you setup

V-Chip ratings limits, these programs will

not be blocked. Parents are cautioned to

preview the contents of these programs or

movies.

❒ PG-13 – Parents Strongly Cautioned.

Parents with children under 13 are cautioned

that the content of movies with this rating

may include more explicit sexual, language,

and violence content than movies rated PG.

NOTE (For Canadian Viewers):

V-Chip function is based on specifications for the United States and therefore may not work properly in Canada.

Download from Www.Somanuals.com. All Manuals Search And Download.

20 V-Chip

❒ R Restricted.

Notes About Unrated Programs:

These films contain material that is explicit in

nature and is not recommended for

unsupervised children under the age of 17.

Unrated programming refers to any

programming which does not contain a rating

signal. Programming on television stations

which do not broadcast rating signals will be

placed in the “Unrated Programming" category.

❒ NC-17 No One Under 17.

These movies contain content which most

parents would feel is too adult for their children

to view. Content can consist of strong language,

nudity, violence, and suggestive or explicit

subject matter.

Examples of Unrated programs:

Emergency Bulletins

Locally Originated Programming

News

Political Programs

Public Service Announcements

Religious Programs

Sports

❒ X No One under 18.

Inappropriate material for anyone under 18.

Directions to Block Movie Viewing:

To block viewers from any or all of these ratings

categories, press the

to the correct location. Press the

buttons to turn the locking feature on or off. An

item is blocked if the

a “—".

Weather

Some Commercials

or to move the cursor

• TV programs or movies that do not have

rating signals will be blocked if the Unrated

Category is set to BLOCK.

icon appears instead of

For example, to block viewing of X and NC-17

rated from shows:

Directions to Block Unrated Programs:

You can block programs that are not rated.

To the X Column

Press the MENU button

To V-CHIP

To turn on the lock

^N17 R ^P13 PG G NR

C-

G-

To operate (Lock icon

appears)

—

— — — — —

Press ZERO to access V-Chip setup

options

FINISH

To UNRATED

To the NC-17 Column

To turn on the lock

UNRATED

VIEW BLOCK

^N17 R ^P13 PG G NR

C-

G-

To VIEW or BLOCK

— — — — —

Press EXIT when done

FINISH

To FINISH

To save settings and exit

NOTES:

• In order for V-Chip settings to take effect, V-Chip settings must be turned ON in the V-Chip menu (page 18).

• You can automatically unblock all of your restrictions by turning V-Chip settings OFF in the V-Chip menu (page 18).

• You can always unblock a restriction by re-entering the V-Chip menu and removing the lock icon.

Download from Www.Somanuals.com. All Manuals Search And Download.

V-Chip 21

Continued…

Accessing V-Chip Information:

• For Children's programming you can block

TV-Y7 and Y programs by Pressing “0” when Y

is displayed during a program. Programming

for audiences other than children’s audiences

will not be affected.

To access Rating information about a certain

program, press the V-CHIP button while viewing

that program. A display like this will appear:

PROGRAM IS RATED :

TV-PG - V

Set Lock Code

If you decide you want to block this category of

viewing, press "0" while the above screen is

visible, and all programs from that category will

be blocked.

Channel Guard and V-Chip settings are protected

by a four-digit Lock Code. Your TV comes pre-set

with a Lock Code of "0000". You may change the

code to any four-digit number you wish. To

Example 1:

change the Lock Code, follow the steps below.

If you want to set your V-Chip settings to block

all programming above TV PG:

Press the MENU button

To SET LOCK CODE

Press ZERO when TV-PG is

displayed

To operate

TV TV TV TV TV TV

— — —

—

The padlock icon will appear

V/ FV

Press ZERO to access the Lock Code

LOCK CODE

0 0 0 0

FINISH

All Programming above TV PG will be

blocked.

The first digit will be highlighted

Example 2:

To select the number

If you want to set your V-Chip settings to block

all programming above a current setting such

as TV PG-V (with violence):

To move to the next digit

Continue to follow these directions for all four

numbers

Press ZERO when TV-PG - V is displayed

To FINISH

TV TV TV TV TV TV

To save your settings and exit

— — — — — —

V/ FV

—

— — —

— —

All Programming above TV PG with

Violence will be blocked!

Continued…

NOTES:

• After a power interruption you must reset the Lock Code.

• Write your Lock Code number down and keep it hidden from potential viewers.

• If you forget the Lock Code, a new code may be set using the steps listed above.

Download from Www.Somanuals.com. All Manuals Search And Download.

22 Picture Settings

Noise Muting

This feature inserts a blank blue screen over

channels which are not broadcasting or are too

weak to be received clearly.

Tint

Tint allows you to adjust the levels of red and green in

your TV picture.

To TINT

To increase the levels of green

To increase the levels of red

To move to the next setting

Press the MENU button

To NOISE MUTING

To turn Noise Muting ON or OFF

Color

• Noise Muting will not work during Auto Tuner

The color function lets you make all the colors in the

TV picture appear either more vivid or subtle.

Setup or when you operate Channel Summary.

Set Video Status

With Set Video Status, you can save your own set

of picture quality adjustments as “Choice” and

have access to them at the touch of a button.

To COLOR

To make the colors more vivid

To make the colors more subdued

To move to the next setting

Press the MENU button

To SET VIDEO STATUS

To operate

Picture

Picture allows you to adjust the levels of black and

white on the TV screen, giving you a darker or

brighter picture overall.

TINT

-------------

COLOR -------------

PICTURE -------------

BRIGHT -------------

DETAIL -------------

-------------

To PICTURE

To increase the level of contrast

To decrease the level of contrast

To move to the next setting

SAVE AS CHOICE

Bright

You can adjust the overall brightness of the TV

picture with the Bright control.

To set the TINT levels

To move to the next option

To BRIGHT

Repeat these steps until all levels are set.

To lighten the picture

To darken the picture

To move to the next setting

To SAVE AS CHOICE

To save settings and exit

• You must use SAVE AS CHOICE to exit the Set

Video Status menu, otherwise your preferences

will not be saved.

Detail

The Detail feature adjusts the level of fine detail

displayed in the picture.

• You can access your “Choice” settings at any

time by pressing the VIDEO STATUS button on the

remote control.

To DETAIL

To make the picture sharper (more details)

To make the picture smoother (less detail)

To move to the next setting

NOTES:

The setting screen will disappear if you do not make any adjustments or move to the next setting in approximately three

seconds. Any changes you have made to picture settings up to that point will be stored. You can exit the Picture Settings

menu at any time by pressing the EXIT button on the remote control.

Download from Www.Somanuals.com. All Manuals Search And Download.

Sound Settings 23

MTS (Multi-Channel Television Sound)

Bass

MTS technology allows several audio signals to be

broadcast at once, giving you a choice in what

you wish to hear with a TV program. In addition to

mono or stereo sound, an MTS broadcast may

also include a Second Audio Program (SAP).

You can increase or decrease the level of

low-frequency sound in the TV’s audio with the

Bass adjustment.

Press the MENU button

To BASS

Press the MENU button

To MTS

To increase the bass

To decrease the bass

To move to the next setting

MTS

STEREO SAP

MONO

ON AIR

Treble

Use Treble to adjust the level of high-frequency

sound in your TV’s audio.

Select the mode

Press the MENU button

To TREBLE

(The ON AIR arrow tells you if a broadcast

is in Stereo and/or contains an SAP).

• Keep the TV in STEREO mode to get the best

sound quality. The sound will work in STEREO

mode even if a certain broadcast is in MONO

sound only.

To increase the treble

To decrease the treble

To move to the next setting

• Choose the MONO setting to reduce excessive

noise on a certain channel or broadcast.

• Selecting SAP will allow you to hear an

alternative soundtrack, if one is available.

Balance

Adjust the level of sound between the TV’s two

speakers with the Balance setting.

Press the MENU button

To BALANCE

Some Sound Advice

You can tell if a program is broadcast in stereo

by the position of the ON AIR arrow in the MTS

menu screen. Unfortunately, while many

To shift the balance towards the right

speaker

programs are originally broadcast in stereo,

some cable companies may “squash” the

transmission to mono sound because they have

only mono equipment. If you are connected to a

cable system, the sound quality is determined

by the cable company. If they broadcast only in

mono, you will receive only mono sound, even if

the program was aired in stereo.

To shift the balance towards the left

speaker

To move to the next setting

Fortunately, most stereo programs are

broadcast by the major television networks. If

you connect an antenna to your TV instead of

cable and set the tuner mode in Auto Tuner

Setup to “Air” instead of “Cable” you will be

able to pick up stereo broadcasts in their

original stereo format

NOTES:

You can leave the Sound Settings menu at any time by pressing the EXIT button on the remote control.

Download from Www.Somanuals.com. All Manuals Search And Download.

24 General Items

On/Off Timer

Timer Note for PIP Models:

The On/Off timer lets you program your television

to turn itself on or off. You can use it as an alarm

to wake up, to help you remember important

programs, or as a decoy when you're not home.

If the television is on when a timed event is about

to start a Timer Preview window will appear. The

Timer Preview window will appear in the lower right

corner of the screen seven seconds before the

timer is programmed to begin. When the timer

activates, the Preview picture will become the main

picture.

Press the MENU button

To ON/OFF TIMER

To operate (begins with ON TIME)

ON TIME

OFF TIME

CHANNEL

MODE

7:00 PM

10:00 PM

ONCE EVERYDAY

YES NO

ON/ OFF TIMER

FINISH

To set the hour (AM/PM) you want the TV

to turn on

Seven seconds before Timer

Activates....

To move to minutes

To set the minutes

To accept ON TIME and move to OFF

TIME (the time the TV will turn off). Set the

OFF TIME the same way as ON TIME

To accept OFF TIME and move to

CHANNEL

Timer

Activated

To select channel

To move to MODE

(Preview of ON/OFF Timed

Program)

Choose ONCE or EVERYDAY

To ON/OFF TIMER

Seven seconds later...

Choose YES to accept the timer setting,

choose NO if you don't wish to accept

To FINISH

To save settings

Timer Activates

NOTES:

• On/Off Timer cannot be set to locked or guarded channels. In order for the On/Off Timer to work, the clock must be set.

After a power interruption Timer settings must be reset.

• PIP Models include AV-36150, AV-35155, AV-32150, and AV-27150.

Download from Www.Somanuals.com. All Manuals Search And Download.

General Items 25

TV Speaker

If your TV is connected to a stereo system, you can

turn off the TV speakers and listen to the audio

through your stereo.

Closed Caption

Use this function to display the Closed Captioning

text onscreen (when included in a broadcast).

Press the MENU button

To CLOSED CAPTION

To operate

Press the MENU button

To TV SPEAKER

MODE

CAPTION

TV SPEAKER

OFF

CAPTION : CC1 CC2 CC3 CC4

TEXT T1 T2 T3 T4

To turn the TV's speakers ON or OFF

EXIT when finished

FINISH

• Before you turn the TV Speaker setting from OFF to

ON, make sure that theTV volume level is low! If

the TV volume is set too high, the sound level will be

extremely loud.

To select CAPTION, TEXT, or OFF

To move to CAPTION or TEXT

To select a caption (CC1 to CC4) or text

(T1 to T4) channel

• After a power interruption, the TV Speaker settings

will return to “ON”.

To FINISH

Audio Out

To save settings and exit

If your television is connected to an external

speaker source, Audio Out gives you the option of

controlling the volume level with your TV’s remote

control.

Press the MENU button

To AUDIO OUT

AUDIO OUT

VARI

FIX

To VARI or FIX

VARI: Lets you adjust the volume of the external

speakers using the VOLUME +/- buttons on

your TV’s remote control.

FIX: The volume of the external speakers is

adjusted using the audio device’s remote

control.

NOTES:

Closed Captions subtitles are usually found on caption channel CC1. Some programs may include additional text

information which is usually found on text channel T1. The other channels are available for future use.

Closed captioning may not work correctly if the signal being received is weak or if you are playing a video tape.

Most broadcasts containing Closed Captioning will display a notice at the start of the program.

External Speakers: When using external speakers or amplifiers, shut off the TV Speakers (see ‘TV Speakers’) above.

TV Speaker and Audio Out are available on all models except AV-32115.

Download from Www.Somanuals.com. All Manuals Search And Download.

26 Button Functions

Video Status

The VIDEO STATUS button gives you a choice of

three TV picture display settings, including a

display of your own preferences.

The MENU button allows you to access JVC’s

onscreen menu system. Press MENU to activate the

onscreen menu system.

• See individual topics (like “Sound Settings) for

specific information on using menus.

Standard - Resets the picture display to the

factory settings.

Exit

Choice - Displays the setting levels you specified

on the "Set Video Status" Menu (see page 22).

Press the EXIT button to leave a menu screen or to

turn off the PIP feature (page 28).

Theater - Gives a rich, film-like look to video.

Press the VIDEO STATUS button

Display

The Display screen shows the current status of timers

and inputs.

Sleep Timer

Press the DISPLAY button

The Sleep Timer can turn the TV off for you after you

fall asleep. Program it to work in intervals of 15

minutes, for a total time of up to 180 minutes.

NOW

SLEEP TIMER

ON/ OFF TIMER

ON TIME

12:20 PM

OFF

EVERYDAY

7:00 PM

10:00 PM

Press the SLEEP TIMER button

OFF TIME

SleepTimer Message

•

The channel or AV input (Channel 07)

• The current time (12:20 pm)

20 seconds before the automatic shutoff, this

message will appear:

• Sleep Timer status/minutes remaining

(The Sleep Timer is off)

GOOD NIGHT!!

PUSH SLEEP TIMER BUTTON

TO EXTEND.

• On/Off Timer status (Set to turn on

everyday at 7:00 PM, off at 10:00 PM)

• Each Press of the DISPLAY button

changes the display mode:

You then have 20 seconds to press the Sleep Timer

button to delay the shutoff for another 15 minutes.

Input

Selects the input source: TV (cable or antenna

input) or Video (VCR or other video device).

All models except AV-32115:

Display - Full screen shown above

Time - Shows the current time only

Channel - Shows the current channel

Off - Turns Display off

INPUT

• You may also turn off the Display at any step by

pressing EXIT.

AV-32115 Users:

NOTES:

Please note that if the Clock, Sleep Timer or On/Off Timer are not set, the Display screen will show: "Clock Not Set",

"Sleep Timer OFF", and "On/Off Timer Off" respectively.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions 27

Return+

Hyper Surround

The RETURN+ button has two functions:

Creates a deep, three-dimensional sound effect

by channeling the audio through the TV's

front-firing speakers. Press the HYPER SURROUND

button to turn the effect on or off.

Return - Returns to the channel viewed just

before the channel currently onscreen.

Return+ - Lets you program a specific channel to

return to while scanning through the channels.

HYPER SURROUND

ON OFF

• Hyper Surround is available on all models

RETURN+ and hold for three seconds

except AV-32115.

RETURN CHANNEL

PROGRAMMED !

Muting

The MUTING button instantly turns the volume down

completely when you press it.

Scan using the Channel+/- buttons

RETURN+

MUTING

You will return to your programmed

channel.

The volume level will instantly go to zero.

• To restore the volume to its previous level, press

MUTING again.

• To cancel your Return+ channel, press and hold

the RETURN+ button for three seconds. The

message “RETURN CHANNEL CANCELLED!” will

appear.

• Return+ works only with CHANNEL+/-. Pressing

any number key will cancel Return+.

• Return+ does not effect the PIP channel.

• For more information on Return and Return+,

turn to page 11.

Number Buttons - 10 Key Pad

To move directly to a specific channel, enter the

channel number with the number buttons on the

remote. For example, to move to Channel 7:

0 (zero)

7 (seven)

VCR Buttons

100+ Button

Use the 100+ button to directly access channels

above Channel 99. For example to move to

channel 124:

You can use this remote control to operate the

basic functions of your VCR. These functions

include: play, record, rewind, fast-forward, stop,

pause, channel scan, TV / VCR, power on, and

power off.

100+

• The remote is preset with the code 000 to control

JVC-brand VCR’s. For any other manufacturer’s

brand VCR, please see the code chart and

instructions on page 13.

2 (two)

4 (four)

Download from Www.Somanuals.com. All Manuals Search And Download.

28 Button Functions - PIP

FREEZE

PIP (Picture-In-Picture)

Use the FREEZE button to lock a single, still image

onto the PIP window.

PIP displays two separate pictures on screen.

Your television has 2-Tuner PIP, meaning you can

view pictures from two different channels

simultaneously. A special set of PIP control buttons

are located on the upper part of the remote

control. Descriptions of each button appear on this

page.

FREEZE

• If PIP is off when FREEZE is pressed, a snapshot

of the main screen is taken and placed in the

PIP window.

Note: PIP is available on the following models

only: AV-36150, AV-35115, AV-32150, AV-27150.

• If PIP is on when FREEZE is pressed, the image

in the window when the button was pressed is

held.

ON/MOVE

Turn PIP on by pressing the ON/MOVE button.

SWAP

You can exchange the channel displayed on the

main screen for the one shown in the PIP window

by pressing SWAP.

(PIP) ON/MOVE

SWAP

CHANNEL +/- For PIP

Like the main CHANNEL +/- buttons, CHANNEL +/-

for PIP lets you scan through the channels in the

PIP window.

CHANNEL +/-

EXIT to turn PIP off

• Direct channel selection with the 10 key pad for

PIP is not possible.

Once PIP is turned on, you can move the PIP

window to any of the TV’s main picture’s four

corners with the ON/MOVE button.

SOURCE

You can select the signal source for the PIP

window image.

ON/MOVE

SOURCE

• If the PIP tuner does not have a signal, the PIP

window will be blue.

• Each press of ON/MOVE will shift the PIP window

to a different corner.

NOTES:

• In order for PIP to work, the television must be set to “TV mode”. If you play a videotape, your TV will switch to “VCR

mode”. The TV only sees one signal in VCR mode. In order to use PIP, press the TV/VCR button to return to TV Mode.

• The PIP window is /₉the size of the full screen.

• PIP will not display blocked channels or programs. A blue screen will display instead.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting 29

Download from Www.Somanuals.com. All Manuals Search And Download.

30 Limited Warranty

For Canadian model televisions, see separate sheets for Warranty/Garantie and

JVC Authorized Service Centers in Canada.

JVC COMPANYOF AMERICAwarrants this product and all parts thereof, except as set forth below ONLYTO THE ORIGINALPURCHASER ATRETAIL

to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIPfrom the date of original retail purchase for the period shown below (the “Warranty

Period”) (PICTURE TUBE is covered for Two (2) years.)

Parts

Labor

1 YEAR

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND COMMONWEALTH OF

PUERTO RICO.

WHAT WE WILL DO:

If this product is found to be defective within the warranty period, JVC will repair or replace defective parts at no charge to the

original owner. Such repair and replacement services shall be rendered by JVC during regular business hours at JVC authorized

service centers. Parts used for replacement are warranted only for the remainder of this Warranty Period. All products and parts

thereof may be brought to a JVC authorized service center on a carry-in basis. Televisions with a screen size of 25 inches and larger may be

covered on an in-home basis where such service is available.

WHAT YOU MUST DO FOR WARRANTY SERVICE:

To determine if in-home service is available in your area, either contact the selling dealer (retailer) or call 1-800-537-5722 to locate the nearest JVC

authorized service center. Service locations can also be obtained from our website http://ww w .jvcservice.com. In-home service, if available, will require

clear access to the Television by the service representatives. If in-home service is not available, carry in service will be provided.

If service is not locally available, box the product carefully, preferably in its original carton, and ship, insured,with a copy of your bill of sale

plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location which will be given to you by

the toll free number.

If you have any questions concerning your JVCProduct, please contact our Customer Relations Department.

WHAT IS NOT COVERED:

This limited warranty provided by JVC does not cover:

1) Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty

installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to

render such service, or if affixed to any attachment not provided with the products, or if the model or serial number has been altered,

tampered with,defaced or removed;

2) Initial installation,installation and removal from "built-in" entertainment centers and other mounting systems;

3) Operational adjustments covered in the Owner’s Manual,normal maintenance, video and audio head cleaning;

4) Damage that occurs in shipment,due to an act of God, and cosmetic damage;

5) Signal reception problems and failures due to line power surge;

6) Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;

7) Accessories;

8) Batteries (except that Rechargeable Batteries are covered for 90 days from date of purchase.)

There are no express warranties except as listed above.

THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILTY, IS LIMITED TO THE

DURATION OF THE EXPRESSWARRANTY HEREIN.

JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE,OR ANY OTHER DAMAGES,WHETHER DIRECT,

INCIDENTAL OR CONSEQUENTIAL (INCLUDING,WITHOUT LIMITATION, DAMAGE TO TAPES, RECORDS OR DISCS) RESULTING FROM THE

USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING

THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET

FORTH ABOVE.

Some states do not allow the exclusion of incidental or consequential damages or limitations on how long the warranty lasts, so these

exclusions or limitations may not apply to you.This warranty gives you specific legal rights and you may also have other rights which vary

state to state.

JVC COMPANYOF AMERICA

1700 Valley Road

DIVISION OF JVC AMERICAS CORP.

Wayne, New Jersey 07470

http://ww w .jvcservice.com

REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY.THIS WARRANTY DOES NOT APPLY FOR DETAILS OF

REFURBISHED PRODUCT WARRANTY. PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION

PACKAGED WITH EACH REFURBISHED PRODUCT.

For customer use:

Enter below the Model No.and Serial No.which is located either on the rear, bottom or side of the cabinet.

Retain this information for future reference.

Model No.:

Serial No.:

Purchase Date:

Name Of Dealer:

Download from Www.Somanuals.com. All Manuals Search And Download.

Authorized Service Centers 31

QUALITY

SERVICE

HOW TO LOCATEYOUR JVC SERVICE CENTER

TOLL FREE: 1 (800) 537-5722

http://www.jvcservice.com

Dear Customer;

In order to receive the most satisfaction from your purchase, read the instruction booklet before operating the unit. In the

event that repair is necessary, or for the address nearest your location, please refer to the factory service center list below

or within the Continental United States, call 1-800-537-5722 for your authorized servicer. Remember to retain your Bill of

Sale for Warranty Service.

— JVC

JVC SERVICE & ENGINEERING

COMPANY OF AMERICA

DIVISION OF JVC AMERICAS CORP.

FACTORY SERVICE CENTER LOCATIONS

Dear customer;

In order to receive the most satisfaction from your purchase, read this guide before operating the unit, and before calling for

service make sure you check the Troubleshooting pages at the end of this book. In the event that repair is necessary, or for

the address nearest you, please refer to the factory service center list below, or within the continental United States, call the

toll free number above for an authorized service center. Remember to retain your bill of sale for warranty service.

10 New Maple Avenue

Pine Brook, NJ 07058-9641

(973) 396-1000

1500 Lakes Parkway

Lawrenceville, GA 30243-5857

(770) 339-2582

705 Enterprise Street

Aurora, IL 60504-8149

(630) 851-7855

5665 Corporate Avenue

Cypress, CA 90630-0024

(714) 229-8011

2969 Mapunapuna Place

Honolulu, HI 96819-2040

(808) 833-5828

10700 Hammerly Suite 110

Houston, TX 77043

(713) 935-9331

13 Cummings Park

Woburn, MA 01801

(781) 376-9100

8192 State Road 84

Davie, FL 33324

(954) 472-1960

890 Dubuque Avenue

South San Francisco, CA 94080-1804

(650) 871-2666

Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and

production of the wide array of JVC products, service is key to maintaining the high level of performance for which JVC

is world famous. The JVC service and engineering organization stands behind our products.

NATIONAL HEADQUARTERS

JVC SERVICE & ENGINEERING COMPANY OF AMERICA

DIVISION OF JVC AMERICAS CORP.

1700 Valley Road

Wayne, New Jersey 07470

IF YOU SHIP THE PRODUCT

Don’t service it yourself

CAUTION

Pack your JVC unit in the original carton or one of equivalent

size and strength. Enclose, with the unit, a letter stating the

problem or symptom that exists and also a copy of the receipt or

bill of sale you received when you purchased your JVC unit. Print

your home return address on the outside and inside of the

carton, Send to the appropriate JVC Factory Service Center as

listed above.

To prevent electrical shock, do not open the

cabinet. No user serviceable parts inside.

Refer to qualified service personnel.

ACCESSORIES

To purchase accessories for your JVC product, you may contact your local JVC Dealer. Or from the

48 Continental United States call toll free : 1 (800) 882-2345

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Specifications subject to change without notice.

JVC COMPANY OF AMERICA

Division of JVC Americas Corp.

1700 Valley Road

JVC CANADA, INC.

21 Finchdene Square

Scarborough, Ontario

Canada, M1X 1A7

Wayne, New Jersey, 07470

LCT0572-001B-A

0200-TN-JII-JIM

Download from Www.Somanuals.com. All Manuals Search And Download.

Ingersoll Rand Heat Pump PE10P AXS XXX A0S User Manual
Insignia TV DVD Combo NS LTDVD19 09CA User Manual
Intellinet Network Solutions Security Camera 550000 User Manual
Invacare Mobility Aid 1109379 User Manual
Jabra Network Card A125s User Manual
JVC VCR HR E239EG User Manual
Kenwood Bread Maker BM450 User Manual
Kenwood CD Player KDC 2029 User Manual
King Canada Saw 8370 User Manual
KitchenAid Double Oven KEBK276SBL04 User Manual