COLOUR TELEVISION
Contents
AV-1414EE
AV-1434EE
AV-2104EE
AV-2114EE
AV-2124EE
AV-2134EE
AV-1434TEE
AV-2104TEE
AV-2134TEE
Locations ................................ 2
Preparation ............................. 4
Basic operation ....................10
Remote control buttons
and functions........................ 11
Using the TV’s menus..........14
Using the button
on the TV...............................17
Viewing a teletext
INSTRUCTIONS
Thank you for purchasing this JVC
colour television.
To ensure your complete
understanding, please read this
manual thoroughly before operation.
programme ...........................19
Troubleshooting ...................21
Specifications.......................22
WARNING:
TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
• TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES
REGARDING THE USE OF THIS TV.
• Operate only from the power source specified on the TV.
• Avoid damaging the power plug and power cord.
• Avoid improper installation and never position this TV where good ventilation is
unattainable. When installing this TV
distance recommendations must be
maintained between the floor and
15 cm
wall, as well as installment in a tightly
enclosed area or piece of furniture.
Adhere to the minimum distance
guidelines shown for safe operation.
• Do not allow objects or liquid into the cabinet openings.
10 cm
10 cm
15 cm
• In the event of a fault, unplug this TV and call a service technician. Do not
attempt to repair it by yourself or remove the rear cover.
• When you don’t use this TV for a long period of time, be sure to disconnect the
power plug from the AC outlet.
LCT1029-001A-H
0701-Ki-NV-JMT
2001 VICTOR COMPANY OF JAPAN, LIMITED
Download from Www.Somanuals.com. All Manuals Search And Download.
Locations
RM-C364GY
RM-C360GY
1
2
ECO
SENSOR
POWER
POWER
2
0
-
0
-
SYSTEM
COLOUR SOUND
SYSTEM
PICTURE
MODE
PICTURE
MODE
COLOUR SOUND
3
4
3
4
1
2
3
6
9
1
2
3
6
9
TV/VIDEO
TV/VIDEO
4
5
8
0
4
5
8
0
=
=
5
5
OFF
OFF
7
7
TIMER
TIMER
CHANNEL
SCAN
CHANNEL
SCAN
6
RETURN+
6
RETURN+
- --
/
- --
/
~
~
7
8
7
8
DISPLAY
MUTING
DISPLAY
MUTING
!
@
!
@
MENU
MENU
CHANNEL
VOLUME
CHANNEL
VOLUME
#
#
9
9
REMOTE CONTROL UNIT
RM-C364GY
REMOTE CONTROL UNIT
RM-C360GY
1 ECO SENSOR button
2 SOUND SYSTEM button
3 COLOUR SYSTEM button
4 TV/VIDEO button
p.11
p.11
p.11
p.10
p.12
p.13
p.13
p.12
p.10
0 POWER button
- PICTURE MODE button
= Number buttons
~ -/-- button
p.6,10
p.12
p.10
p.10
p.11
5 OFF TIMER button
6 CHANNEL SCAN button
7 RETURN + button
! MUTING button
@ MENU buttons
• MENU
buttons
/
• MENU –/+ buttons
8 DISPLAY button
# VOLUME –/+ buttons
p.10
9 CHANNEL –/+ buttons
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
1. Connecting the aerial and external devices
Notes: .........................................................................................................................
• For further details, refer to the manuals provided with the devices you are connecting.
• Connecting cables are not supplied.
• The front and rear AUDIO/VIDEO input jacks are directly connected so that input to either
jack is output through both.You cannot provide input to both the front and rear jacks at the
same time. Disconnect one input, or use one of the jacks as an output jack only (for
monitoring or recording).
• The rod aerial is supplied with the AV-1434TEE/AV-1414EE/AV-1434EE.
....................................................................................................................................
■ Connecting the aerial and VCR
Connecting the aerial
To install rod aerial:
Install into the top-rear aerial holder. Once installed, it cannot be removed.
VHF/UHF outdoor aerial
Indoor aerial
Rod aerial
VIDEO
AUDIO
IN
OUT
• Illustration of AV-1434EE.
Connecting the aerial and VCR
VHF/UHF outdoor aerial
2
VIDEO
AUDIO
IN
OUT
3
To video
output
To audio
output
To RF
output
1
VCR
To aerial input
• Illustration of AV-1434EE.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Preparation
■ Connecting other external devices
To audio
output
To video
output
VIDEO AUDIO
VCR (for playing)
IN
OUT
VCR (for recording)
To audio
input
To video
input
• Illustration of AV-2104EE.
To video
output
Camcorder
or
To audio
output
TV game
MENU
VIDEO AUDIO
IN
Headphones
• Illustration of AV-2104EE.
Note: ..................................................................................................................
• Use the headphones with a stereo mini jack (3.5 mm in diameter). When you connect
the headphones, the TV speakers go off.
...........................................................................................................................
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
2. Connecting the power cord
Insert the Power plug into an AC outlet.
3. Inserting batteries into the remote control
Correctly insert two batteries, observing the
end first.
and
polarities and inserting the
CAUTION: ...........................................
• Follow the cautions printed on the
batteries.
............................................................
Notes: .................................................
• Use AA/R6/UM-3 dry cell batteries.
• If the remote control does not work
properly, fit new batteries.
The supplied batteries are for testing, not
regular use.
............................................................
4.Turning your TV on
1. Press the Main power button on the TV to turn the TV’s main power
on.
The POWER lamp or POWER/ON TIMER lamp lights.
If image does not appear:
Your TV is in the standby mode. Press the POWER button on the remote control
to turn your TV on.
• You can also turn on your TV by pressing the CHANNEL –/+ button on your TV.
To turn your TV off:
Press the POWER button on the remote control.Your TV enters the standby
mode.
To turn the TV’s main power off:
Press the Main power button on the TV.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
5. Selecting the on-screen language
You can select the language for the on-screen display.
1. Press MENU
to display the MENU 3 menu,
then select LANGUAGE.
/
MENU
AUTO CH PRESET
MANUAL CH PRESET
3
LANGUAGE
ENGLISH
/
2. Press MENU
or –/+ to select language.
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
The on-screen displays indications are in the selected
language.
6. Presetting TV stations
To view a TV programme, you must first preset TV channels to channels on the TV.
This TV has 100 channels (channel 1 to 99 and channel AV).
■ Auto Channel Preset
You can automatically preset all TV channels that can be received by your TV to
channels.
• The Auto Channel Preset function does not preset a TV channel to the AV channel
(channel number 0).
• If the TV cannot preset the TV channel you want to view, preset it manually. For details see
“Manual Channel Preset” on page 8.
1. Press MENU
to display the MENU 3 menu,
then select AUTO CH PRESET.
MENU
AUTO CH PRESET
MANUAL CH PRESET
3
/
LANGUAGE
ENGLISH
/
2. Press MENU
or –/+ to start the Auto
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
Channel Preset function.
ON SEARCH is displayed on the screen.
When you have finished presetting all TV channels that can be received on your
TV, the display will go out and the Auto Channel Preset function will end.
/
• To stop the Auto Channel Preset, press the MENU
or –/+ button.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
■ Manual Channel Preset
You can manually preset the desired TV channels to the desired channels.
MENU
AUTO CH PRESET
MANUAL CH PRESET
3
1. Press MENU
to display the MENU 3 menu,
then select MANUAL CH PRESET.
/
LANGUAGE
ENGLISH
/
2. Press MENU
or –/+.
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
The sub-menu is displayed.
• The channel No. is displayed as a PR No.
MANUAL
FINE
SKIP
NO
SOUND SYSTEM
EXIT
B/G
/
3. Press MENU
or –/+ to select the
Channel
No.
channel number.
SELECT BY
PROGRAM BY -+
SEARCH BY VOL-+ DISPLAY
PR 1 VL
EXIT BY
4. Press VOLUME –/+ to start searching for
the TV channel.
or
is displayed on the screen.
When a TV channel is received, the
or
display goes out, and the TV
station is preset to the currently selected channel No.
• If the TV channel you want to preset is not displayed, repeat step 4 until the TV finds the
TV channel you want to preset.
• To stop the Manual Channel Preset function, press any button other than the VOLUME
–/+ button.
If the picture is not clear:
Use the Fine function to fine-tune the TV station.
1. Press MENU
to select FINE.
/
MANUAL
FINE
SKIP
SOUND SYSTEM
EXIT
NO
B/G
2. Hold VOLUME –/+ down to fine-tune theTV station
so that the best image is displayed on screen.
or indicates that the TV station is being
fine-tuned.
SELECT BY
PROGRAM BY -+
FINE
PR 3 VL
EXIT BY
BY VOL-+ DISPLAY
5. Press MENU
to select SOUND SYSTEM.
/
MANUAL
FINE
SKIP
NO
SOUND SYSTEM
EXIT
B/G
6. Press VOLUME –/+ to select the appropriate
SELECT BY
PROGRAM BY -+
CHANGE BY VOL-+ DISPLAY
PR 3 VL
EXIT BY
sound system.
• For the sound systems in each country or region, refer to the
table “Broadcasting systems” on page 22.
7. Press MENU
to select MANUAL.
/
8. Repeat steps 3 to 7 if you want to preset another TV station to a
channel.
9. Press DISPLAY to turn the display off.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
■ Skip
You can set undesired channels to be skipped.
Channels set to be skipped cannot be selected by the CHANNEL –/+ buttons nor
the CHANNEL SCAN button.
• Channels to which a station has not been preset are automatically set to be skipped.
1. Press MENU
PRESET.
to select MANUAL CH
MENU
AUTO CH PRESET
MANUAL CH PRESET
3
/
LANGUAGE
ENGLISH
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
/
MANUAL
FINE
SKIP
SOUND SYSTEM
EXIT
2. Press MENU
or –/+.
The sub-menu is displayed.
NO
B/G
SELECT BY
PROGRAM BY -+
PR 1 VL
EXIT BY
SEARCH BY VOL-+ DISPLAY
MANUAL
FINE
SKIP
3. Press MENU
to select SKIP.
/
• The channel No. is displayed as a PR No.
NO
SOUND SYSTEM
EXIT
B/G
Channel
No.
SELECT BY
PROGRAM BY -+
YES/NO BY VOL-+ DISPLAY
PR 1 VL
EXIT BY
/
4. Press MENU
or –/+ to select the channel you want to skip.
5. Press VOLUME –/+ to select YES.
The channel you selected is set to be skipped.
To cancel the Skip:
select NO.
6. Repeat steps 4 and 5 if you want to set another channel to skip.
7. Press DISPLAY to turn the display off.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic operation
• The illustration below is for the remote
control RM-C90 supplied with TEE series
models.
2. Select a channel.
■ Press the CHANNEL –/+
button.
• Up/down selection cannot be selected
for channels to which the Skip has
been set to YES. (See page 9.)
ECO
SENSOR
POWER
■ Press the Number buttons
to enter the channel
number.
SYSTEM
COLOUR SOUND MUTING
DISPLAY
TV/TEXT
• If you want to enter a two-digit
number, press the -/-- button to select
the two digit mode “--”, then enter the
channel number.
MENU
TV/VIDEO
If the colour is abnormal:
Repeatedly press the COLOUR
SYSTEM button to select the
appropriate colour system. For
details, see “Colour System” on
page 11.
1
4
2
5
8
0
3
6
9
OFF
TIMER
PICTURE
MODE
7
CHANNEL
SCAN
RETURN+
- --
/
CHANNEL
VOLUME
3. Press VOLUME –/+ to adjust
the sound.
TEXT
If the sound is abnormal:
Repeatedly press the SOUND
SYSTEM button to select the
appropriate sound system. For
details, see “Sound System” on
page 11.
REVEAL HOLD
SUBPAGE
INDEX
SIZE
CANCEL
TV
RM-C90
4. To turn your TV off, press
POWER.
• We recommend that you press the
Main power button on the TV to turn
the main power off if you do not plan
to use your TV for a long time or if you
wish to save energy.
1. Press the POWER button to
turn your TV on.
Viewing Images from an
External Device:
Press the TV/VIDEO button to
• If your TV does not turn on, press the
Main power button on the TV then
press the POWER button again.
• You can also turn on your TV by
pressing any of the following buttons;
– the CHANNEL –/+ button
select the VIDEO mode.
• You can also use the Input function to
select the VIDEO mode. For details,
refer to page 14.
– the Number buttons
– the TV/VIDEO button
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
Eco Sensor
Sound System
<AV-1414EE does not have this
function.>
If the sound is abnormal, select the
appropriate sound system. Each press
of the SOUND SYSTEM button
You can adjust this TV so that the
screen automatically adjusts to the
optimum contrast according to the
brightness of your room. This function
reduces eye strain and the power
consumption of this TV.
changes the sound system as follows.
B/G
I
D/K
• For the sound systems in each country or
region, see the table “Broadcasting
Systems” on page 22.
• You cannot select any sound system
when in VIDEO mode.
Repeatedly press the ECO SENSOR
button to select the desired mode.
• AV-2104TEE/AV-2104EE does not display
“DIGITAL”.
Colour System
If the colour is abnormal, select the
appropriate colour system. Each press
of the COLOUR SYSTEM button
DIGITAL ECO SENSOR
DISPLAY:
The Eco Sensor function will work.
In this mode, the mark indicating the
brightness of your room is displayed
for several seconds each time the
brightness changes. The number of
marks displayed on screen increases
as your room becomes darker.
changes the colour system as follows.
In TV mode (channel 1 to 99 and
AV):
SECAM
AUTO
PAL
In VIDEO mode:
DIGITAL ECO SENSOR:
AUTO
PAL
SECAM
The Eco Sensor function will work.
However, in this mode, the mark will
not be displayed even if the brightness
of your room changes.
NTSC4.43
NTSC3.58
AUTO:
Automatic colour system selection.
• For the colour systems in each country or
region, see the table “Broadcasting
Systems” on page 22.
• If the colour is abnormal even though you
selected AUTO, change the appropriate
colour system manually.
DIGITAL ECO SENSOR OFF:
The Eco Sensor function will not work.
Muting
You can turn the volume off instantly.
This is convenient when answering the
phone or when you have visitors.
Press the MUTING button.
To return the sound, press the
MUTING button again.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
Display
Picture Mode
You can continuously display the
current channel number or VIDEO
mode on the screen.
Press the DISPLAY button.
To turn the display off, press the
DISPLAY button again.
You can select one of three picture
adjustment modes.
Repeatedly press the PICTURE
MODE button to select the desired
mode.
BRIGHT:
• When selecting a channel or VIDEO mode
with no input signal, indication of selected
channel or VIDEO mode becomes fixed
on the screen.
Heightens contrast and sharpness.
STANDARD:
Standardizes picture adjustments.
SOFT:
Off Timer
Softens contrast and sharpness.
• Pressing the PICTURE MODE button
returns all the picture settings in the
MENU 4 menu to their default settings.
You can set this TV to turn off
automatically within a specified period
of time.
Repeatedly press the OFF TIMER
button to select the period of time.
• You can set the period of time a maximum
of 120 minutes in 10 minute increments.
• 1 minute before the Off Timer turns off the
TV, GOOD NIGHT! displays.
To display the remaining time:
Press the OFF TIMER button once.
To cancel the Off Timer:
Press the OFF TIMER button to return
the period of time to 0.
• The Off Timer will not turn off the TV’s
main power.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
Channel Scan
Return +
You can search for the channel you
want to view while scanning all of the
channels that can be viewed on this
TV.
You can set a channel you frequently
view to the Return Channel and you
can view that channel at any time with
one-touch.
To set the channel to the Return
Channel:
1. Press CHANNEL SCAN.
Channels will be scanned in
channel No. order.
1. Select the channel you want to
set to the Return Channel.
2. When the channel that you
want to view appears, press
CHANNEL SCAN again
before scanning for the next
channel begins.
2. Press RETURN + and hold until
the message RETURN PLUS
PROGRAMMED! appears.
• When you turn off the TV, the Return
Channel setting is cancelled.
• Channel Scan selection cannot be
selected for channels to which the
Skip has been set to YES. (See page
9.)
To view the Return Channel:
Press the RETURN + button.
• You can view two channels (current
channel and Return Channel) alternately
by pressing this button.
To cancel the Return Channel
setting:
Press the RETURN + button and hold
until the message RETURN PLUS
CANCELLED! appears.
If no channel is set to the Return
Channel:
You can view the channel selected
right before the current channel by
pressing this button.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menus
When the time set for the On
On Timer
Timer function is reached:
The TV automatically turns on and the
channel set for the On Timer function
is displayed.
Your TV will automatically turn on and
tune into the channel you set after the
period of time you set.
• For safety reasons the TV will
automatically turn off if no operations are
made within approximately two hours after
the TV is turned on with the On Timer
function.
1. Press MENU
to display
the MENU 1 menu, then
/
select ON TIMER.
• The Off Timer function and Auto Shutoff
function have priority over the On Timer
function.
MENU
1
TV
INPUT
ON TIMER
VNR
Channel
No.
PR 1 0:00
OFF
PROGRAM BY -+
SELECT BY
OPERATE BY VOL-+ DISPLAY
Input
EXIT BY
You can view images from VCRs or
other devices connected to your TV.
/
2. Press MENU
or –/+ to
select a channel you want to
view when the TV turns on.
1. Press MENU
to display
the MENU 1 menu, then
select INPUT.
/
3. Press VOLUME –/+ to select
the period of time after which
you want to turn on the TV.
The On Timer function starts.
MENU
1
INPUT
TV
ON TIMER
PR 1 0:00
OFF
VNR
• Each time you press the button, the
period of time changes in 15 minute
intervals (up to 12 hours).
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
To cancel the On Timer function,
press the VOLUME –/+ button to
set the period of time to 0:00.
/
2. Press MENU
or –/+ to
select the VIDEO mode.
TV mode changes to VIDEO mode.
4. Press DISPLAY to turn the
display off.
• If you turn off the TV’s main power by
pressing the Main power button, the
On Timer function is canceled.
• If you do not turn off the TV after
starting the On Timer function, the
channel will automatically switch to
the channel set for the On Timer
function.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menus
/
2. Press MENU
select ON.
or –/+ to
VNR (Video Noise Reduction)
You can reduce the picture noise.
To cancel the Child Lock function,
select OFF.
1. Press MENU
to display
the MENU 1 menu, then
select VNR.
/
3. Press DISPLAY to turn the
display off.
• The Child Lock function is canceled
when you turn the TV’s main power
off.
MENU
1
TV
INPUT
ON TIMER
VNR
PR 1 0:00
OFF
Auto Shutoff
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
You can set your TV to turn off if no
signals are received for about 15
minutes or longer after the end of a
broadcast.
/
2. Press MENU
select ON.
or –/+ to
To cancel the VNR function, select
OFF.
1. Press MENU
to display
the MENU 2 menu, then
select AUTO SHUTOFF.
/
3. Press DISPLAY to turn the
display off.
MENU
AUTO SHUTOFF
CHILD LOCK
BLUE BACK
2
OFF
OFF
ON
Child Lock
You can disable the front control
buttons of the TV.
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
When this function is set to ON, the TV
can be operated using only the remote
control.
/
2. Press MENU
select ON.
or –/+ to
Use this function to prevent children
from operating the TV at their own
discretion (without parental consent).
To cancel the Auto Shutoff function,
select OFF.
3. Press DISPLAY to turn the
display off.
1. Press MENU
to display
the MENU 2 menu, then
select CHILD LOCK.
/
• The Auto Shutoff function does not
turn off the TV’s main power.
• The Auto Shutoff function will not work
for a VIDEO mode.
MENU
AUTO SHUTOFF
CHILD LOCK
BLUE BACK
2
OFF
OFF
ON
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menus
Blue Back
Picture Adjustment
You can mute the sound and change
the picture into a blue screen while no
signals are received by the TV, or
when the signals are unstable.
You can adjust the picture as you like.
1. Press MENU
repeatedly
/
to display the MENU 4.
MENU
4
1. Press MENU
to display
the MENU 2 menu, then
select BLUE BACK.
/
TINT
COLOUR
BRIGHT
CONT.
SHARP
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
MENU
AUTO SHUTOFF
CHILD LOCK
BLUE BACK
2
OFF
OFF
OFF
2. Press MENU
to select an
/
/
item and press MENU
or
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
–/+ to adjust it.
Item
/
2. Press MENU
select ON.
or –/+ to
Reddish
Lighter
Darker
Lower
TINT
Greenish
Deeper
Brighter
Higher
COLOUR
BRIGHT
CONT.
To cancel the Blue Back function,
select OFF.
• To view a broadcast even when the
reception signal is poor, set the Blue
Back function to OFF.
Softer
SHARP
Sharper
• Even when the Blue Back function is
set to OFF, the sound may not be
audible.
• TINT (tint) is displayed only when
viewing images from NTSC3.58 or
NTSC4.43 colour systems.
3. Press DISPLAY to turn the
display off.
3. Press DISPLAY to turn the
display off.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the button on the TV
<AV-2104TEE/AV-2134TEE/AV-2104EEI/AV-2134EE>
1 MENU buttons
• MENU button
ON
TIMER POWER
MENU
CHANNEL
VOLUME
EXIT
• MENU –/+ buttons
2 CHANNEL –/+ buttons
3 VOLUME –/+ buttons
3
4
7
2
5
1
<AV-2114EE>
4 ON TIMER lamp
The light is switched on while
On Timer function is operating.
MENU
CHANNEL
VOLUME
ON TIMER POWER
EXIT
5 POWER lamp
When the Main power is on,
the light is red.
1
2
3
4 5 7
6 POWER/ON TIMER lamp
When the Main power is on,
the light is green.
<AV-2124EE>
MENU
VOLUME
EXIT
CHANNEL
ON TIMER POWER
When On Timer function is on,
it is red.
7 Main power button
4
5
1
2
3
7
<AV-1434TEE/AV-1434EE>
MENU
CHANNEL
VOLUME
EXIT
ON TIMER POWER
1
2
3
4
5
7
<AV-1414EE>
MENU
CHANNEL
VOLUME
+
+
–
–
POWER/
ON TIMER
EXIT
–
+
1
2
3
6
7
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the button on the TV
Basic operation
Operating menus
• Check to make sure the Child Lock
function is set to OFF. When the Child
Lock function is set to ON, the TV cannot
be operated using the front control
buttons. For details, see “Child Lock” on
page 15.
You can operate functions in menus using
the front control buttons on the TV.
1. Press MENU repeatedly to
display the menu you want to
use.
1. Press CHANNEL –/+ to turn
the TV on from standby
mode.
2. Press MENU to select the
desired function or item.
3. Press MENU –/+ or VOLUME
–/+ to carry out the desired
operation.
2. Press CHANNEL –/+ to select
a channel.
3. Press VOLUME –/+ to adjust
• For details, see the description for
each function.
the volume.
4. To turn your TV off, press the
Main power button to turn off
the TV's main power.
4. Press VOLUME –/+ to turn
the menu display off.
To turn the sub-menu display
off:
1. Press MENU
to select EXIT.
MANUAL
FINE
SKIP
NO
SOUND SYSTEM
EXIT
B/G
SELECT BY
PROGRAM BY -+
PR 1 VL
EXIT BY
EXIT
BY VOL-+ DISPLAY
2. Press VOLUME –/+ to turn the
display off.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing a teletext programme
<AV-1434TEE/AV-2104TEE/AV-2134TEE only.>
Basic operation
ECO
1. Select a TV channel with a
POWER
SENSOR
teletext programme.
SYSTEM
COLOUR SOUND MUTING
2. Press TV/TEXT to change the
TV mode to the teletext
mode.
DISPLAY
TV/TEXT
1
MENU
TV mode
TEXT mode
(TEXT only)
TV/VIDEO
1
4
2
5
8
0
3
6
9
OFF
TIMER
3. Select a teletext page by
pressing the CHANNEL –/+
button, number button or
coloured buttons.
PICTURE
MODE
7
CHANNEL
SCAN
RETURN+
- --
/
CHANNEL
VOLUME
To return to the TV mode, press the
TV/VIDEO button or the TV/TEXT
button.
TEXT
2
3
REVEAL HOLD
SUBPAGE
INDEX
SIZE
6
• If you have trouble receiving teletext
broadcasts, consult your local dealer
or the teletext station.
CANCEL
4
5
7
8
TV
RM-C90
1 TV/TEXT button
2 Coloured buttons
3 REVEAL button
4 SUBPAGE button
5 HOLD button
6 SIZE button
7 CANCEL button
8 INDEX button
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing a teletext programme
Display cancel
Index return
You can view a normal TV programme
while scanning for a teletext page you
wish to view.
You can easily return to the index page
by pressing INDEX.
Fastext/WST: Returns to teletext
page 100 or a page
which has been
1. Select the page you want to
view.
specified.
Scanning starts.
LIST mode: Returns to the page
number displayed in
red in the lower left
2. Press CANCEL.
The TV programme appears.
area of the screen.
3. Press TV/TEXT when the
page number you wish to
view appears in the upper left
of the screen.
Sub page display
Some teletext pages have sub-pages,
which scroll automatically.You can
store those pages in memory and view
them again later on.
Page hold
You can hold a page temporarily even
as the teletext transmission continues.
To do this, press the HOLD button.
Pressing the HOLD or INDEX button,
or selecting another teletext page will
release the hold mode.
1. Select a teletext page with
sub-pages.
2. Press SUBPAGE.
The input position appears at the
bottom left of the screen.
3. Enter the sub-page number
using the number buttons.
Example:
Hidden information
reveal
To select the third page,
press 0, 0, 0, 3.
• You can also select a sub-page
number by pressing the red or
green colour button.
Some teletext pages contain hidden
information such as answers to
questions.You can reveal the hidden
information with this function.
To alternate reveal and hide, press the
REVEAL button.
Display size
You can double the height of the
teletext display.
To do this, press the SIZE button
repeatedly.
The teletext display changes cyclically.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Important: Review all the instructions in this manual.
Problem
Check/Action
Cannot turn TV on
Press the Main power button (see p.6).
Insert the power plug in an AC outlet.
No picture nor sound
Press the TV/VIDEO button to select the correct mode (see p.10).
Check the aerial connections.
Remote control inoperable Replace the batteries (see p.6).
Insert the batteries correctly.
Buttons on front of TV do
not work
Is the Child Lock function ON ? (see p.15).
The TV turns on suddenly The TV will automatically turn on when the On Timer is
operated (see p.14).
The TV turns off suddenly The TV will automatically turn off in the following cases.
• When the Off Timer or Auto Shutoff is operated (see p.12
and p.15).
• When no operations are made within approximately two hours
after the TV was turned on with the On Timer (see p.14).
Abnormal sound
Abnormal colour
Select the appropriate sound system (see p.11).
Adjust the colour and brightness (see p.16).
Select the appropriate colour system (see p.11).
Set the Picture mode to STANDARD (see p.12).
Lines or streaks in picture
(interference)
Move the components apart until the interference disappears.
Reposition the aerial.
Spotted picture (crosstalk) Move the aerial away from the source of interference.
Replace the aerial cable with a coaxial cable, which is less
prone to interference.
Double picture (ghost)
Reposition the aerial.
Replace with an aerial with good directionality.
Snowy picture
(image noise)
Check the aerial connection and aim it correctly.
Replace or repair the aerial.
The TV channel changes
suddenly
The channel will automatically be changed when the On Timer
operates (see p.14).
The screen turns blue
Is the Blue Back set to ON ? (see p.16).
No receivable teletext
programme
Select a channel with teletext information.
You cannot watch teletext recorded on a video tape.
The following are normal occurrences and are not the result of TV
malfunctions:
• When a still bright image (of a white dress, for example) appears on the screen, the image
may be coloured. This problem occurs in all CRTs, and when the bright image disappears,
the colouration also disappears.
• This TV is equipped with a microcomputer that may operate abnormally due to interference
from external devices. If this happens, press the Main power button to turn the main power
off and disconnect the power plug from the AC outlet. Then, reconnect the power plug to the
AC outlet and press the Main power button again.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
TV RF systems
B, G, I, D, K, K1
PAL, SECAM, NTSC 3.58 / 4.43 MHz (in VIDEO mode only)
= 46.25 to 168.25 MHz
VHF high channel (VH) = 175.25 to 463.25 MHz
UHF channel (U) = 471.25 to 863.25 MHz
Colour systems
Channel and frequencies VHF low channel (VL)
■ Receives cable channels in mid band (X to Z, S1 to S10),
super band (S11 to S20) and hyper band (S21 to S41) .
Teletext system
Fastext (United Kingdom system), WST (Standard system)
Language displayed by
teletext
English, Estonian, Lithuanian, Russian, Czechoslovakian,
Ukrainian, Latvian, Romanian, Hungarian
External input / output
VIDEO input (RCA)
AUDIO input (RCA)
VIDEO output (RCA)
AUDIO output (RCA)
Headphone jack: mini jack (dia. 3.5 mm)
Design and specifications subject to change without notice.
Broadcasting Systems
System
Area
Country or Region
Sound
Colour
Bahrain, Kuwait, Oman, Qatar,
United Arab Emirates, Yemen, etc.
Indonesia, Malaysia, Singapore,
Thailand, India, etc.
PAL
B/G
Asia,
Middle
East
China, Vietnam, etc.
PAL
PAL
D/K
I
Hong Kong, etc.
Islamic Republic of Iran, Lebanon,
Saudi Arabia, etc.
SECAM
B/G
Russia, etc.
SECAM
PAL
D/K
D/K
B/G
I
Czech Republic, Poland, etc.
Germany, Holland, Belgium, etc.
UK, etc.
Europe
PAL
PAL
Oceania
Africa
Australia, New Zealand, etc.
Republic of South Africa, etc.
Nigeria, etc.
PAL
B/G
I
PAL
PAL
B/G
B/G
Egypt, Morocco, etc.
SECAM
22
Download from Www.Somanuals.com. All Manuals Search And Download.
|