COLOUR TELEVISION
Contents
Setting up your TV . . . . . . . . . . . . . 3
TV buttons and functions . . . . . . . . 6
Remote control buttons
and functions . . . 8
HV-34LH21
HV-34LH51
HV-34LH71
HV-29VH21
HV-29WH21
HV-29WH51
HV-29WH71
Using the TV's menu. . . . . . . . . . . . 19
Basic operation . . . . . . . . . . . . . . 19
PICTURE SETTING menu . . . . . 20
PICTURE FEATURES menu . . . 21
SOUND SETTING menu . . . . . . 25
FEATURES menu . . . . . . . . . . . 26
INSTALL menu . . . . . . . . . . . . . . 29
Additional preparation . . . . . . . . . . 35
Troubleshooting . . . . . . . . . . . . . . 37
Specification . . . . . . . . . . . . . . . . . 40
INSTRUCTIONS
GGT0020-001B-H
0803-CR-JMT
© 2003 VICTOR COMPANY OF JAPAN, LIMITED
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
CAUTION
• Turn off all the equipment including the
TV before connecting anything.
1 Connecting the aerial and VCR
• Aerial cable is not supplied. Use a
good quality 75-ohm coaxial cable.
• Read the manual that came with the
VCR before connecting.
Fig. A
Back of the TV
If not connecting a VCR (see Fig. A):
AUDIO
R
L/MONO VIDEO
S
OVER
Connect an aerial cable to the aerial socket
on this TV.
VIDEO-1
VIDEO-2
If connecting a VCR (see Fig. B):
CR
CB
Y/VIDEO
VIDEO-3/
1 Connect the aerial cable to the aerial
input socket on the VCR, and connect
the VCR and TV with another aerial
cable.
R AUDIO L/MONO
COMPONENT
OUTPUT
R
L
VIDEO
AUDIO
2 Connect the VCR’s VIDEO OUT (video
output) jack and the TV’s VIDEO jack
with a video cable.
To connect a VCR to the TV with an S-
VIDEO cable:
Connect the VCR’s S-VIDEO OUT (S-
VIDEO output) connector and TV’s S
connector with an S-VIDEO cable A,
instead of connecting with a video cable.
Fig. B
Back of the TV
A
AUDIO
L/MONO VIDEO
R
S
OVER
VIDEO-1
VIDEO-2
CR
CB
Y/VIDEO
3 Connect the VCR’s VIDEO OUT (audio
L/R output) jacks and the TV’s AUDIO
jacks (L/MONO and R) with an audio
cable.
VIDEO-3/
COMPONENT
R
AUDIO L/MONO
OUTPUT
R
L
VIDEO
AUDIO
• If the VCR’s audio output is in mono,
connect the VCR’s AUDIO OUT (audio
output) jack and the TV’s AUDIO L/
MONO jack with an audio cable.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
2 Connecting the power cord
Connect the mains plug to the AC outlet.
3 Putting the batteries into the
remote control
Use two AA/R6 batteries.
Insert the batteries from the - end, making
sure the +and - polarities are correct.
• Follow the warnings printed on the
batteries.
• If the remote control does not work
properly, replace the batteries.
• The batteries we supply are only for
setting up and testing your TV. Please
replace them as soon as necessary.
HV-34LH21 / HV-34LH51 /
HV-34LH71
4 Making the initial settings
When the TV is first turned on, it enters the
initial setting mode, and the JVC logo is
displayed.
1 Press the main power button on the
TV.
The TV is turned on, and the JVC logo
appears.
POWER
• If the POWER lamp on the TV lights
red and does not change to green,
your TV is in the standby mode. Press
the POWER button on the remote
control to turn the TV on.
POWER lamp
Main power button
• If the JVC logo does not appear, your
TV has already been turned before. In
this case, use the “LANGUAGE” and
“AUTO PROGRAM” functions to make
the initial settings. For details, see
“INSTALL menu” on page 29.
HV-29WH21 / HV-29WH51 /
HV-29WH71 / HV-29VH21
2 Press the MENU/OK button.
The LANGUAGE menu appears. You
can choose a language for the on-screen
language.
POWER
POWER lamp
Main power button
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
3 Press the 6 buttons to choose
ENGLISH. Then press the MENU/ OK
button.
The AUTO PROGRAM function starts.
The TV channels you receive are
automatically stored in the PR
(programme numbers) LIST.
MUTING
POWER
SYSTEM
CINEMA
COLOUR SOUND SURROUND ZOOM
PIP
DISPLAY
Except
HV-34LH21
HV-29WH21
HV-29VH21
MENU
OK
TV/TEXT
Except
HV-34LH51
TV/VIDEO
HV-29WH51
1
4
7
2
5
8
0
3
6
9
PICTURE
MODE
• To stop the AUTO PROGRAM
function, press the MENU/OK button.
SUB-P
Except
+
RETURN
4 After the TV channels have been
stored in the programme numbers
(PR) list, the EDIT menu appears.
HV-34LH21
HV-29WH21
HV-29VH21
CHANNEL
VOLUME
FAVORITE CH
RM-C1350
TV
HV-34LH71 / HV-29WH71
• You can proceed to edit the
programme numbers list using the
EDIT/MANUAL function. For details,
see “EDIT/MANUAL” on page 30.
• If a TV channel you want to view is not
stored in the programme numbers list,
you can register it using the MANUAL
function. For details, see “EDIT/
MANUAL” on page 30.
FAVORITE CH
RM-C1351
TV
HV-34LH21 / HV-29VH21 / HV-29WH21
FAVORITE CH
• The AUTO PROGRAM function does
not store a TV channel to the
programme number 0 (AV).
• If you do not need to use the EDIT/
MANUAL function, press the MENU/
OK button to close the EDIT menu.
RM-C1353
TV
HV-34LH51 / HV-29WH51
Now, setting up is complete. Please
enjoy your new JVC TV!
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TV buttons and functions
Turn the main power on
Press the main power button 1.
The POWER lamp 2 lights red and your TV
is in the standby mode.
HV-34LH21 / HV-34LH51 /
HV-34LH71
To turn the main power off:
Press the main power button again. The
POWER lamp 2 goes off.
Turn the TV on from standby
mode
Press the CHANNEL-/+ buttons 5.
The POWER lamp 2 lights red to green
and your TV will be turned on.
POWER
• You can also turn on the TV by
pressing the TV/VIDEO button 3
while it is in standby mode.
7
2
1
HV-29WH21 / HV-29WH51 /
HV-29WH71 / HV-29VH21
Choose a TV channel
Press the CHANNEL-/+ buttons 5.
Choose a VIDEO terminal
Press the TV/VIDEO button 3 or
CHANNEL-/+ buttons 5.
Adjust the volume
Press the VOLUME-/+ buttons 4.
The volume level indicator appears.
MENU button 6
Press to open the menu.
POWER
For details, see “Operation with the buttons
on the TV” on page 20.
7
2
1
Remote control sensor 7
(Behind the cover)
HV-34LH21 / HV-34LH51 /
HV-34LH71
HV-29WH21 / HV-29WH51 /
HV-29WH71 / HV-29VH21
VIDEO-4 terminal 8
See page 35.
Headphone jack 9
Connect the headphones with a stereo
mini-jack (3.5mm in diameter).
(Behind the cover)
OVER
V
L/MONO
R
S
MENU
OK
CHANEL
VOLUME TV/VIDEO
EXIT
IN (VIDEO-4)
9
8
6 5 4 3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TV buttons and functions
VIDEO-1 terminal 0
• See pages 3 and 35.
VIDEO-2 terminal -
• See page 35.
VIDEO-3/COMPONENT
A
UDIO
L/MONO
VIDEO
S
R
OVER
VIDEO-1
VIDEO-2
terminal =
CR
CB
Y/VIDEO
A
UDIO
VIDEO-3
COMPONENT
R
R
L/MONO
OUTPUT
L
UDIO
VIDEO
A
• See pages 28 and 35.
OUTPUT terminal ~
• See page 35.
AUDIO
L/MONO
VIDEO
S
R
Aerial socket !
Connect the aerial cable.
• See page 3.
OVER
VIDEO-1
VIDEO-2
0
-
CR
CB
Y/VIDEO
VIDEO-3/
COMPONENT
R AUDLI/OMONO
=
~
OUTPUT
R
L
VIDEO
AUDIO
!
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
Turn the TV on from standby
mode
Press the POWER button.
The POWER lamp lights red to green and
MUTING
POWER
your TV will be turned on.
SYSTEM
CINEMA
COLOUR SOUND SURROUND ZOOM
• You can turn on the TV from the
standby mode by pressing the TV/
VIDEO button, the CHANNEL-/+
buttons or the number buttons.
PIP
DISPLAY
Except
HV-34LH21
HV-29WH21
HV-29VH21
MENU
OK
TV/TEXT
To turn the TV off:
Except
HV-34LH51
HV-29WH51
Press the POWER button again.
The POWER lamp changes from green to
red and the TV enters standby mode.
TV/VIDEO
1
4
7
2
5
8
0
3
6
9
PICTURE
MODE
Choose a TV channel
Choose a programme number in which a
TV channel has been set.
SUB-P
Except
+
RETURN
HV-34LH21
HV-29WH21
HV-29VH21
CHANNEL
VOLUME
FAVORITE CH
Press the CHANNEL-/+ buttons or enter
the programme number (PR) with the
number buttons.
• If you want to put a two-digit channel
into the TV, press the -/--button to
change to the two-digit entry system.
• You can select a channel from the PR
LIST. For details, see “DISPLAY
button” on page 11.
RM-C1350
TV
• If you do not have a clear picture or no
colour appears, follow the operation
procedure “COLOUR SYSTEM button”
on page 11.
HV-34LH71 / HV-29WH71
FAVORITE CH
Adjust the volume
Press the VOLUME-/+ buttons.
RM-C1351
TV
Watch images from an
external device
Choose a VIDEO terminal to which the
external device has been connected.
HV-34LH21 / HV-29VH21 / HV-29WH21
FAVORITE CH
Press the TV/VIDEO button.
• You can choose a VIDEO terminal with
the CHANNEL-/+ buttons or from the
PR LIST.
RM-C1353
TV
HV-34LH51 / HV-29WH51
To return to a TV channel:
Press the TV/VIDEO button, the
CHANNEL-/+ buttons or the number
buttons.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
MUTING button
Press the MUTING button to turn off the
volume. Pressing the MUTING button again
resumes the previous volume level.
CINEMA SURROUND button
You can enjoy an enhanced sound for a
wider audience by using CINEMA
SURROUND function.
Press the CINEMA SURROUND button to
select one of CINEMA SURROUND
modes.
ZOOM button
You can change the screen size according
to the picture aspect ratio. Choose the
optimum one from the following ZOOM
modes.
HIGH/LOW:
When you listen to the stereo sound, please
select HIGH or LOW mode.
You can enjoy the sound for a wider
audience similar to the experience at the
theatre.
Press the ZOOM button to choose a
mode.
• The ZOOM button works only in the
normal screen.
• In case that you setting up the
CINEMA SURROUND function to
HIGH mode, there may be slight
volume distortion. In case that occurs,
please switch the HIGH mode to LOW
mode, the effect of CINEMA
SURROUND functions will be less
noticeable, however, the volume
distortion will be corrected.
REGULAR:
Use to view a normal picture (4:3 aspect
ratio) as its original size is.
ZOOM:
You can zoom up the Wide picture (16:9
aspect ratio) to fill the TV screen.
MONO:
Select the MONO mode, when you listen to
the mono sound.
You can enjoy the sound for a wider
audience similar to stereo sound.
OFF:
The CINEMA SURROUND function
switches off.
• The left side and right side of the Wide
picture (16:9 aspect ratio) will be cut
off.
PICTURE MODE button
You can choose one of three PICTURE
MODEs (three kinds of picture setting) to
adjust the picture settings automatically.
16:9:
This mode converts a normal picture (4:3
aspect ratio) into a Wide picture (16:9
aspect ratio).
Press the PICTURE MODE button to
choose a mode.
BRIGHT:
Heightens contrast and sharpness.
• Use for picture with a 16:9 aspect ratio
that have been squeezed into a normal
picture (4:3 aspect ratio), you can
restore their original dimensions.
STANDARD:
Standardizes picture adjustment.
SOFT:
Softens contrast and sharpness.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
RETURN function
RETURN+ button
The TV temporarily memorises the TV
channel that was chosen right before the
current TV channel as the “Last Channel”.
By pressing the RETUTN+ button, you can
alternately view the current TV channel and
the “Last Channel”.
The RETURN+ button has two functions;
the RETURN+ function and the RETURN
function. If a channel has been registered
as the “Return Channel”, the RETURN+
function operates. If there is no setting for
the “Return Channel”, the RETURN function
operates.
• If you want to view two channels
alternately by using the RETURN
function, first choose one TV channel
and then choose the other TV channel
with the Number buttons. If you choose
the TV channel without using the
Number buttons, there are cases
where a channel other than the one
you first chose is registered as the
“Last Channel”.
RETURN+ function
By registering a channel you frequently
view as the “Return Channel”, you can
select that channel at any time simply by
pressing the RETURN+ button.
To register a TV channel as the “Return
Channel”:
Choose the Programme number to which
the channel you want to register has been
set, and press the RETURN+ button and
hold for more than 3 seconds continuously.
“RETURN PLUS PROGRAMMED!” is
displayed and the registration is completed.
svt/ubutton
When you are viewing a bilingual broadcast
programme, you can choose the sound
from Bilingual I (Sub I) or Bilingual II (Sub
II).
To cancel a TV channel registered as the
“Return Channel”:
• When the stereo broadcasting is
received poorly, you can change from
stereo to mono sound so that you can
hear the broadcast more clearly and
easily.
While viewing any TV channel, press the
RETURN+ button and hold for more than 3
seconds continuously. “RETURN PLUS
CANCELED!” is displayed and the
registration is cancelled.
Press the svt/ubutton to choose a
• When you turn off the TV, the
registration for the “Return Channel” is
cancelled.
sound mode.
s
v
t
: Stereo sound
: mono sound
: Bilingual I (sub I)
: Bilingual II (sub II)
• If you want to view the “Return
Channel” and another TV channel
alternately, first choose a channel
other than the “Return Channel”. And
then press the RETURN+ button to
change the channel to the “Return
Channel” In this way, you can view two
channels alternately by pressing the
RETURN+ button.
u
MONO : Cancels the Multi Sound function,
and the sound becomes
monaural.
• The sound mode you can choose
differs depending on the TV
programme.
• This function does not work in the
VIDEO modes.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
DISPLAY button
COLOUR SYSTEM button
The colour system is chosen automatically.
However, if the picture is not clear or no
colour appears, choose the colour system
manually.
You can display the PR LIST, programme
number or VIDEO terminal number on the
screen.
Press the DISPLAY button.
Press the DISPLAY button changes the
display as follows:
Press the COLOUR SYSTEM button to
choose the appropriate colour system.
AUTO:
This function detects a colour system from
the input signal.
• The AUTO mode may not function
properly if you have poor signal quality.
If the picture is abnormal in the AUTO
mode, choose another colour system
manually.
No indication
• The AUTO mode detects a colour
system from the input signal and
chooses the appropriate colour system
automatically.
• For the colour systems in each country
or region, see the table
Choose a TV channel or a
VIDEO terminal
1 Press the DISPLAY button to display
the PR LIST.
“BROADCASTING SYSTEMS” on
page 12.
2 Press the 6 and 5 buttons to
choose a programme number or
VIDEO terminal.
PAL/SECAM/NTSC3.58/NTSC4.43:
PAL, SECAM, or NTSC colour system.
Then press the MENU/OK button.
• For programme numbers with the
CHANNEL GUARD function set, the n
(CHANNEL GUARD) mark is
displayed next to the programme
number in the PR LIST.
• The VIDEO terminals are registered
after the programme number PR99.
• The AV channel (channel number 0) in
the PR LIST will be chosen only if you
connect the VCR to the TV with an
aerial cable without connecting a video
cable.
SOUND SYSTEM button
The sound system is chosen automatically.
However, if you cannot hear the sound
normally even when the picture appears
normally, choose the sound system
manually.
Press the SOUND SYSTEM button to
choose the appropriate sound system.
B/G
: B/G system
I
: I system
D/K
M
: D/K system
: M system
• This function does not work in the
VIDEO mode.
• For the sound systems in each country
or region, see the table
“BROADCASTING SYSTEMS” on
page 12.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
BROADCASTING SYSTEMS
For sound and colour systems in your
country or region, refer to the table below:
„ Favorite channel
registration
You can register your favorite TV channels
with the colour buttons (Red, Green, Yellow
and Blue). After registration you can recall
the favorite channel by pressing the colour
button.
COLOUR SYSTEM
Area
Country or Region
System
PAL
Bahrain, Kuwait, Oman,
Qatar, United Arab Emirates,
Yemen, etc.
Indonesia, Malaysia,
Singapore, Thailand, India,
etc.
1 In the normal screen, choose a TV
channel (PR01-99) you want to
register.
Asia,
Middle
East
China, Vietnam, etc.
Hong Kong, etc.
PAL
PAL
For detailed operation, see “Choose a
TV channel” on page 8.
Islamic Republic of Iran,
Lebanon, Saudi Arabia, etc.
SECAM
2 Press and hold a colour button for 3
seconds or more.
Philippines, Taiwan,
Myanmar, etc.
NTSC
Then “FAVORITE CHANNEL
Russia, etc.
SECAM
PROGRAMMED!” appears on the screen
and the current channel is registered.
• If the chosen channel is already
registered as the favorite channel,
when a colour button is pressed, the
registered colour button icon appears
on the top right of the screen.
Czech Republic, Poland, etc. PAL
Europe
Germany, Holland, Belgium,
etc.
UK, etc.
PAL
PAL
Oceania Australia, New Zealand, etc. PAL
Republic of South Africa, etc. PAL
Africa
Nigeria, etc.
PAL
Egypt, Morocco, etc.
SECAM
SOUND SYSTEM
Area Country or Region
• You cannot register in the Text mode,
or while multiple screens, such as PIP
(picture in picture) are displayed.
• Also you cannot register if the chosen
channel is guarded with the CHANNEL
GUARD function and the screen is
blue, or if an on-screen menu is
displayed.
System
B/G
Bahrain, Kuwait, Oman,
Qatar, United Arab Emirates,
Yemen, etc.
Indonesia, Malaysia,
Singapore, Thailand, India,
etc.
China, Vietnam, etc.
Hong Kong, etc.
Asia,
Middle
East
D/K
I
Islamic Republic of Iran,
• Even if you perform AUTO PROGRAM
function, the registration made here
will not be changed. (For AUTO
PROGRAM, see page 29.)
B/G
Lebanon, Saudi Arabia, etc.
Philippines, Taiwan,
Myanmar, etc.
Russia, etc.
M
D/K
Czech Republic, Poland, etc. D/K
Recalling the favorite channel
Press the colour button, then the registered
favorite channel will be displayed.
Europe
Germany, Holland, Belgium,
B/G
etc.
UK, etc.
Oceania Australia, New Zealand, etc. B/G
I
• You cannot recall the favorite channel
in the Text mode, Menu mode where
an on-screen menu is displayed, or
while multiple screens are displayed.
Republic of South Africa, etc.
Nigeria, etc.
Egypt, Morocco, etc.
I
Africa
B/G
B/G
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
• The picture effect dedicated for the
colour button applies. For details, see
“Setting the picture effect” below:
„ Viewing a teletext
programme
[Except HV-34LH51/HV-29WH51]
Setting the picture effect
Each colour button has a dedicated picture
effect. When you choose a favorite channel
with a colour button, the dedicated picture
effect is used. When shipped, the factory
set picture effect is used for this purpose.
However, you can set this picture effect as
required. For details, see “FAVORITE CH
SETTING” on page 24.
1 Choose a TV channel with a teletext
broadcast.
2 Press the TV/TEXT button.
Pressing the TV/TEXT button changes
the mode as follows:
• If you choose the favorite channel
normally without using the colour
button, the normal picture effect is
used.
TV and
Text mode
TV mode
Showing the favorite channels
Press the DISPLAY button to display the
PR LIST.
Text mode
You can see the favorite channel that has
the registered colour button icon at the right
of the channel number.
3 Choose a teletext page by pressing
the CHANNEL-/+ buttons, number
buttons or colour buttons.
To return to the TV mode:
Press the TV/TEXT button or TV/VIDEO
button.
ZDF
BBC1
• If you have trouble receiving teletext
broadcasts, consult your local dealer
or the broadcast station.
• In the Text mode, the ZOOM mode is
fixed to the REGULAR mode.
• No menu operations are possible
when viewing a teletext programme.
• If characters on a teletext programme
do not appear properly, change the
TELETEXT LANGUAGE setting. For
details, see “TELETEXT LANGUAGE”
on page 34.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
3 Press the
(Cancel) button to
(Hold) button
return to a teletext page when the
page number is on the screen.
• You cannot return to the TV mode with
You can hold a teletext page on the screen
for as long as you want, even while several
other teletext pages are being received.
the
(Cancel) button.
Press the
(Hold) button.
(Sub-page) button
The (hold) are displayed at the top left
Some teletext pages include sub-pages that
are automatically displayed. You can hold
any sub-page, or view it at any time.
of the screen.
To cancel the Hold function:
Press the
(Hold) button again.
1 Press the
(Sub-page) button to
operate the Sub-page function.
Sub-page numbers are displayed at the
left of the screen.
(Reveal) button
Some teletext pages include hidden text
(such as answers to a quiz).
You can display the hidden text.
Colour*
Meaning of sub-page number
Currently being displayed.
Can be displayed.
Each time you press the
(Reveal)
Yellow
White
button, text is hidden or revealed.
(Size) button
You can double the height of teletext
display.
Blue or
Red
Cannot be displayed and it is not
sent.
*: Background colour of the sub-page
number.
Press the
(Size) button.
2 Press the CHANNEL-/+ buttons to
choose a sub-page number.
(Index) button
You can return to the index page instantly.
To cancel the
(Sub-page) function:
Press the (Index) button.
Press the
(Sub-page) button again.
• In the List mode, you can return to the
page number displayed in the lower
left area of the screen.
(Cancel) button
You can search for a teletext page while
watching TV.
1 Press the number button to enter a
page number, or press the colour
button.
The TV searches for a teletext page.
2 Press the
(Cancel) button.
The TV programme appears. When the
TV finds the teletext page, its page
number appears in the upper left of the
screen.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
Using the List mode
„ Twin and PIP (picture in
You can store the numbers of your favorite
teletext pages in memory and call them up
quickly using the colour buttons.
picture) function
[Except HV-34LH21/HV-29WH21/
HV-29VH21]
To store the page numbers:
You can display two different pictures, the
main picture and sub picture, at a time. In
Twin mode, both pictures are equal in size.
In PIP mode, the small sub picture appears
at a corner of the screen. You can swap the
main picture and sub picture instantly. Note
that the main and sub pictures use different
input sources each other. For example, if
the main picture’s source is TV, the sub
picture’s one will be VIDEO.
1 Press the MODE button to engage the
List mode.
The stored page numbers are displayed
at the bottom of the screen.
2 Press a colour button to choose a
position. Then press the number
buttons to enter the page number.
3 Press and hold down the
button.
(Store)
The four page numbers blink white to
indicate that they are stored in memory.
While watching a normal picture, press
the PIP button.
Pressing the PIP button changes the mode
as follows:
To call up a stored page:
1 Press the MODE button to engage the
List mode.
Twin mode
Normal screen
2 Press a colour button to which a page
has been assigned.
Sub
To exit the List mode:
Press the MODE button again.
Main
PIP mode
Sub
Main
• You can also enter this mode while in
the Multi-display mode, Freeze mode
or Strobe mode, except in the Text
mode.
To return to the normal screen:
Press the PIP button until the sub picture
disappears.
• You can hear the sound from the main
picture only.
• In the normal screen, if the current
channel is guarded with the CHANNEL
GUARD function and the screen is
blue, the PIP button does not work.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
• When you exit the Twin or PIP mode,
the sub picture lastly displayed will be
saved, and it will appear next time.
• The following table shows what will
happen if the same input sources are
chosen for both main and sub pictures
when you enter the Twin or PIP mode.
If the main picture is the same as the sub
picture, then the sub picture will be
changed to VIDEO-1. But if the main
picture is VIDEO-1, then the sub picture
will be changed to VIDEO-2.
For the sub picture:
Press the
(Input) button.
Each time you press the button, the input
source changes as follow (the one used for
the main picture will be skipped):
VIDEO-1 → VIDEO-2 → VIDEO-3 →
VIDEO-4 → TV
Swapping the pictures
Press the
(Swap) button.
Each time you press the button, the main
picture and the sub picture will be swapped.
[When the same input sources are chosen]
Changing the sub picture
position (in PIP mode only)
You can position the sub picture to one of
corners of the main picture.
Main picture
TV
Sub picture
TV → VIDEO-1
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
VIDEO-1 → VIDEO-2
VIDEO-2 → VIDEO-1
VIDEO-3 → VIDEO-1
VIDEO-4 → VIDEO-1
Press the
(Position) button.
Each time you press the button, the sub
picture moves clockwise (lower right →
lower left → upper left → upper right).
• If you press the PIP button when
receiving the Progressive Video Signal
(525P signal), "525P" appears on the
screen and the Twin/PIP function does
not operate.
Setting the colour system of the
sub picture
You can choose the colour system of the
sub picture.
While the sub picture is being displayed,
press the C.SYS button.
TV channel selection
Each time you press the button, the colour
system of the sub picture changes as
follows:
AUTO → PAL → SECAM → NTSC3.58 →
NTSC4.43
For the main picture:
Choose a channel using the CHANNEL-/+
buttons or the number buttons.
For the sub picture:
Choose a channel using the SUB-P-/+
buttons.
• For all source, normally choose AUTO.
• The chosen colour system will not be
saved.
• If the main picture and the sub picture
are of different colour systems, there
will be some differences in the size of
the sub picture and flicker may take
place.
Input source selection (TV,
VIDEO-1, -2, -3 or -4)
For the main picture:
Press the TV/VIDEO button.
Each time you press the button, the input
source changes as follows (the one used for
the sub picture will be skipped):
VIDEO-1 → VIDEO-2 → VIDEO-3 →
VIDEO-4 → TV
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
SOUND SYSTEM button are disabled
in the Multi-display mode.
„ Multi-display function
[Except HV-34LH21/HV-29WH21/
HV-29VH21]
• If you press the MULTI button when
receiving the Progressive video signal
(525P signal), "525P" appears on the
screen and the MULTI function does
not operate.
You can watch nine different TV
programmes at a time. As you can display
nine TV programmes successively, this
function is convenient to locate the TV
programme you want. Eight pictures are still
pictures and the last one is the moving
picture with the blue frame. You can choose
any picture as the moving picture and then
watch it in the normal screen.
Returning to the normal screen
Press the MULTI button or MENU/OK
button, or choose a TV channel with the
number buttons.
The moving picture with the blue frame will
be displayed in the normal screen.
• Pressing the TV/VIDEO button will also
returns the TV to the normal screen.
Entering the Multi-display mode
While watching a TV programme in the
normal screen, press the MULTI button.
The screen changes to the multi-picture
screen and nine pictures are displayed in
the numerical order.
Choosing a picture as the
moving one
You can choose one of the pictures as the
moving picture with the blue frame.
Press 5and 6buttons to move the
blue frame.
The chosen picture becomes the moving
picture.
• Pressing the 3button in the right-most
position “3” or “6” will scroll the blue
frame to the next position, “4” or “7”.
While, pressing the 2button in the left-
most position “4” or “7” will scroll the
blue frame to the previous position, “3”
or “6”.
Moving picture with the blue frame
•
You can also enter this mode while in the
Twin mode, but not in the Text mode.
Displaying the next nine pictures
• Pictures will appear in the assigned
order in the PR LIST (PR01-99).
• If the number of pictures to be
displayed at a time is less than nine,
fewer pictures than nine will be
displayed.
• The guarded channel with the
CHANNEL GUARD function will be
skipped and will not be displayed.
• You cannot display a video image in
the Multi-display mode.
Press the NEXT button.
The next nine pictures will be displayed at a
time. By pressing the NEXT button
successively, you can display all available
pictures except video images.
Displaying the channel numbers
on the multi-display screen
Press the DISPLAY button.
Respective channel numbers appear on the
nine pictures.
• The RETURN+ button, svt/ubutton,
COLOUR SYSTEM button and
To go off the channel numbers:
Press the DISPLAY button again.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
„ Freeze function
„ Strobe function
[Except HV-34LH21/HV-29WH21/
HV-29VH21]
[Except HV-34LH21/HV-29WH21/
HV-29VH21]
While watching a picture, you can capture a
still picture you want. The captured still
picture and the moving picture are
displayed at a time. (They are the pictures
of the same source.)
You can display eight consecutive still
pictures and one moving picture at a time.
(They are the pictures of the same source.)
Press the STROBE button.
Eight consecutive still pictures which are
captured at intervals of about 0.2 second
are displayed in the order of “1” to “9”.
(These numbers are not actually displayed.)
Press the
(Freeze) button.
Still picture is captured and displayed on the
right side of the screen. On the left, the
moving picture is displayed.
Still
picture
Moving
picture
• The
(Freeze) button does not work
in the Text mode.
To return to the normal screen:
• The STROBE button does not work in
the Text mode.
Press the
(Freeze) button again or
press the number buttons to choose a
channel.
To return to the normal screen:
Press the STROBE button again or press
the number buttons to choose a channel.
• If signal level of the main picture is
weak, the still images become
abnormal.
• You cannot use the FREEZE button
when the sub picture or the main
picture are displayed on the screen.
• If the current channel is guarded with
the CHANNEL GUARD function and
the screen is blue, this button does not
work.
• If you press the FREEZE button when
receiving the Progressive video signal
(525P signal), "525P" appears on the
screen and the FREEZE function does
not operate.
• You cannot use the STROBE button
when the sub picture or the main
picture are displayed on.
• If the current channel is guarded with
the CHANNEL GUARD function and
the screen is blue, the STROBE button
does not work.
• If you press the STROBE button when
receiving the Progressive video signal
(525P signal), "525P" appears on the
screen and the STROBE function does
not operate.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
This TV has a number of functions you can operate using menus.
To fully utilize all your TV’s functions, you need to understand the basic menu operating
techniques fully.
• The following remote control is for HV-34LH71 and HV-29WH71. However, the buttons
used for setting TV menus are common to all models.
Basic operation
1 Press the MENU/OK button to display
the MENU (main menu).
MUTING
POWER
SYSTEM
CINEMA
COLOUR SOUND SURROUND ZOOM
PIP
DISPLAY
• The display appearing at the bottom of
a menu indicates buttons on the
remote control you can use when you
operate a chosen function.
MENU
OK
TV/TEXT
MENU/OK button
OK
TV/VIDEO
1
4
2
5
8
0
3
6
9
TV/VIDEO button
DISPLAY button
TV
PICTURE
MODE
DISP.
7
RETURN
2 Press the 6 buttons or 5to
choose a menu title, and press the
MENU/OK button.
SUB-P
+
CHANNEL
VOLUME
The menu appears.
FAVORITE CH
To return to the previous menu:
Press the DISPLAY button.
To exit a menu instantly:
Press the TV/VIDEO button.
3 Press the 6 buttons to choose a
function.
RM-C1350
TV
• For details of the functions in the
menus, see the following pages.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
4 Press the 5 buttons to choose the
setting of that function.
PICTURE SETTING menu
• If you want to operate a function which
appears only with its name, follow the
descriptions of that function on the
following pages.
• The display appearing at the bottom of
a menu shows you a button on the
remote control that you can use when
you operate a chosen function.
„ PICTURE MODE
5 Press the MENU/OK button to
complete the setting.
You can choose one of three PICTURE
MODEs to adjust the picture settings
automatically.
The menu disappears.
• When watching the television with the
NTSC system, the menus as displayed
at about half of their normal vertical
size.
BRIGHT:
Heightens contrast and sharpness.
STANDARD:
Standardizes picture adjustment.
Operation with the buttons on the
TV
SOFT:
You can also operate the menus using the
buttons on the front panel of the TV.
Softens contrast and sharpness.
• You can also operate the PICTURE
MODE function with the PICTURE
MODE button on the remote control.
For details, see “PICTURE MODE
button” on page 9.
OK
6
5
TV/VIDEO
buttons buttons buttons buttons
„ Adjusting the picture
You can change the picture settings of each
picture mode, as you like. The picture
settings changed are stored in the picture
mode.
MENU
OK
CHANNEL
VOLUME TV/VIDEO
EXIT
CONTRAST
You can adjust the picture contrast.
2: lower
3: higher
• There is no DISPLAY button on the
front panel of the TV, which will be
used for menu operation.
BRIGHT
You can adjust the picture brightness.
2: darker
3: brighter
SHARP
You can adjust the picture sharpness.
2: softer
3: sharper
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
COLOUR
You can adjust the picture colour.
PICTURE FEATURES menu
2: lighter
3: deeper
TINT
You can adjust the picture tint.
2: reddish
3: greenish
• You can change the TINT setting
(picture tint) only when the colour
system is NTSC 3.58 or NTSC 4.43.
• You cannot select the TINT function
when receiving the Progressive video
signal (525P signal).
„ DIGITAL VNR
The DIGITAL VNR function cuts down the
amount of noise in the original picture.
To return to the default settings in each
PICTURE MODE:
Press the blue button. This will return the
picture settings in the currently chosen
PICTURE MODE to the default settings,
and stores them in the PICTURE MODE
again.
AUTO:
The TV will be automatically adjust the level
of the DIGITAL VNR effect to match the
amount of noise in the picture, giving you
the best possible picture.
• If you set the DIGITAL VNR effect too
high it can make the picture less sharp.
It is recommended to use the AUTO
setting if you can.
„ WHITE BALANCE
You can select one of three WHITE
BALANCE modes (three tones of white) to
adjust the white balance of the picture.
Since white is the colour which is used as a
reference for all the other colours, changing
the WHITE BALANCE mode affects the
appearance of all the other colours on the
screen.
MAX:
The level of the DIGITAL VNR effect is set
to the maximum. If you set the DIGITAL VNR
function to AUTO but still notice some noise,
change the setting from AUTO to MAX.
• The MAX setting is not suitable for
high-quality pictures which contain a
lot of noise.
COOL:
A bluish white. Using this mode when
watching bright pictures allows you to enjoy
a more vivid and bright picture.
OFF:
The level of the DIGITAL VNR effect is set
to OFF.
MID:
The normal white colour.
MIN:
WARM:
The level of the DIGITAL VNR effect is set to
the minimum. If you set the DIGITAL VNR
function to AUTO but feel that the sharpness
of the original picture has not been reproduced
fully, change the setting from AUTO to MIN.
• The MIN setting is not suitable for low-
quality pictures which contain a lot of noise.
A radish white. Using this mode when
watching films allows you to enjoy colours
that are characteristic of films.
• You cannot select the WHITE
BALANCE function in the 16:9 mode
of the ZOOM function.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
MIN:
„ DigiPure
The level of the DigiPure effect is set to the
minimum. When you set the DigiPure
function to AUTO and notice some noise,
change the setting from AUTO to MIN.
• The MIN setting is not suitable for
high-quality pictures which contain
very little noise.
The Digipure function uses the latest in
digital technology to give you a natural
looking picture. The Digipure function
includes the following two functions.
Digipure function:
This function helps to create a natural
looking picture by eliminating unnecessary
edges from high-contrast and crisp images.
Conversely, for images with low-contrast,
edges are added to produce a sharper,
more detailed picture.
„ PULL DOWN
The PULL DOWN function displays a
cinema film picture more smoothly and
naturally on the screen.
You can choose from the DigiPure function
settings of AUTO, MIN and MAX.
AUTO:
This function is turned on. Normally keep
Picture motion compensation function:
This function displays fast-moving pictures
(for example, the players or ball in a football
game) more smoothly and naturally on the
screen.
this function set to AUTO.
ON :
This function is turned on.
OFF:
This function is turned off.
AUTO:
• The motion may appear unnatural
when viewing images with the NTSC
colour system. To make the motion
smoother, switch the PULL DOWN
function from AUTO or ON to OFF.
• You cannot select this function in the
Twin pictures mode.
The TV will automatically adjust the level of
the DigiPure effect to match the amount of
noise in the picture, giving the best possible
picture.
• If you set the DigiPure effect too high
on a low-quality picture that contains a
lot of noise, this may actually make the
noise worse. It is recommended to use
the AUTO setting if you can.
When TV displays Twin, PIP, Multi-display,
FREEZE, or STROBE function, PULL
DOWN function cannot operate.
MAX:
The level of the DigiPure effect is set to the
maximum. If you set the DigiPure function
to AUTO but feel that the original picture
quality has not been reproduced fully,
change the setting from AUTO to MAX.
• The MAX setting is not suitable for
low-quality pictures which contain a lot
of noise.
OFF:
The DigiPure function is turned off.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
„ COLOUR SYSTEM
„ ZOOM
The colour system is chosen automatically.
However, if the picture is not clear or no
colour appears, choose the colour system
manually.
You can change the screen size according
to the picture aspect ratio. Choose the
optimum one from three ZOOM modes.
1 Choose ZOOM, then press the MENU/
OK button.
1 Choose COLOUR SYSTEM, then
press the 5 buttons to choose the
appropriate colour system.
• You can also operate the COLOUR
SYSTEM function with the COLOUR
SYSTEM button on the remote control.
For details, see “COLOUR SYSTEM
button” on page 11.
2 Press the 6buttons to choose a
ZOOM mode. Then press the MENU/
OK button.
• You can choose a ZOOM mode from
REGULAR, ZOOM or 16:9 modes. For
details, see “ZOOM button” on page 9.
„ PICTURE TILT
There are cases where the Earth’s
magnetic force may make the picture tilt. If
this happens, you can correct the picture tilt.
1 Choose PICTURE TILT, then press the
MENU/OK button.
2 Press the 6buttons until the
picture becomes level. Then press the
MENU/OK button.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
• For details of each item, see
“PICTURE MODE” on page 20,
“DIGITAL VNR” on page 21, “WHITE
BALANCE” on page 21, “DigiPure” on
page 22.
„ FAVORITE CH SETTING
You can set a dedicated picture effect for
the favorite channels registered to the
colour buttons (Red, Green, Yellow and
Blue). For favorite channel registration, see
“Favorite channel registration” on page 12.
Item
Options
1 Choose FAVORITE CH SETTING, then
press the MENU/OK button.
PICTURE MODE BRIGHT*, STANDARD,
SOFT
DIGITAL VNR
AUTO*, MAX, OFF, MIN
COOL, MID*, WARM
WHITE
BALANCE
DigiPure
AUTO*, MAX, OFF, MIN
PICTURE
EFFECT
ON*:
Above picture effect
applies to the chosen
favorite channel.
OFF:
No picture effect applies.
2 Press the 6button to choose
FAVORITE CHANNEL, then press the
5 button to choose the registered
favorite channel.
*: When shipped
4 Press the MENU/OK button to
complete the setting.
Each time you press the 5button, the
colour button icon (Red, Green, Yellow
or Blue) of the registered favorite
channel and its channel number (e.g.
PR1) appear.
„ VIDEO SETTING
You can set a dedicated picture effect for
the video inputs, VIDEO-1 to -4.
1 Choose VIDEO SETTING, then press
the MENU/OK button.
3 Set the picture effect.
Press the 6 button to choose an item
listed in the following table and press the
5 button to choose one of options.
• As explained in the table, if PICTURE
EFFECT is set to OFF, the dedicated
picture effect for the favorite channel is
not used. In this case, normal picture
effect is used.
2 Press the 6 button to choose
VIDEO STATUS, then press the 5
button to choose one of video inputs,
VIDEO-1 to -4.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
3 Set the picture effect.
SOUND SETTING menu
Press the 6button to choose an item
listed in the following table and press the
5 button to choose one of options.
• As explained in the table, the
PICTURE EFFECT for the video inputs
is set to OFF when shipped. To use it,
you need to set it ON.
Item
Options
„ STEREO / I•II
PICTURE MODE BRIGHT*, STANDARD,
SOFT
When you are viewing a bilingual broadcast
programme, you can choose the sound
from Bilingual I (sub I) or Bilingual II (sub II).
When the stereo broadcasting is received
poorly, you can change from stereo to mono
sound so that you can hear the broadcast
more clearly and easily.
DIGITAL VNR
AUTO*, MAX, OFF, MIN
COOL, MID*, WARM
WHITE
BALANCE
DigiPure
AUTO*, MAX, OFF, MIN
PICTURE
EFFECT
ON:
s :Stereo sound
Above picture effect
applies to the chosen
video input.
v
t
u
: mono sound
: Bilingual I (sub I)
: Bilingual II (sub II)
OFF*:
No picture effect applies.
MONO: Cancels the Multi Sound function,
and the sound becomes monaural.
• The sound mode you can choose
differs depending on the TV
programme.
*: When shipped
• For details of each item, see
“PICTURE MODE” on page 20,
“DIGITAL VNR” on page 21, “WHITE
BALANCE” on page 21, “DigiPure” on
page 22.
• Pressing the number button “0” will
return the picture effect to the factory
set value.
• This function does not work in the
VIDEO modes.
• You can also operate the STEREO /
I•II function with the svt/ubutton.
For details, see “svt/ubutton” on
page 10.
4 Press the MENU/OK button to
complete the setting.
„ Adjusting the sound
You can adjust the sound to your liking.
BASS
You can adjust the low tone of the sound.
2: weaker
3: stronger
TREBLE
You can adjust the high tone of the sound.
2: weaker
3: stronger
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
BALANCE
FEATURES menu
You can adjust the volume balance
between the left and right speakers.
2: turn the left speaker’s volume level up.
3: turn the right speaker’s volume level up.
„ AI VOLUME
You can prevent the sudden increase or
decrease of sound that occurs when
changing the channel to another channel or
switching the VIDEO mode to another
VIDEO mode.
„ SLEEP TIMER
You can set the TV to automatically turn off
after a set time.
ON:
1 Choose SLEEP TIMER, then press the
MENU/OK button.
This function is turned on.
OFF:
This function is turned off.
• The AI VOLUME function may not
operate as expected if the sound input
level from a broadcast station (or video
software) is extremely low.
„ CINEMA SURROUND
You can enjoy Surround sound with a “live”
effect by using the CINEMA SURROUND
function.
2 Press the 5 buttons to set the
period of time.
The TV begins count down from the set
time.
• You can choose a CINEMA
SURROUND mode from HIGH, LOW,
MONO and OFF modes. For details,
see “CINEMA SURROUND button” on
page 9.
• You can also operate the CINEMA
SURROUND function with the
CINEMA SURROUND button. For
details, see “CINEMA SURROUND
button” on page 9.
• You can set the period of time a
maximum of 120 minutes (2 hours) in
10 minute steps.
To cancel this function:
• Press the 2button to set a period of
time to “OFF”.
3 Press the MENU/OK button to
complete the setting.
The menu disappears.
• One minute before this function turns
off the TV, “GOOD NIGHT!” appears.
• This function cannot be used to turn off
the TV’s main power.
• When this function is on, you can
display the SLEEP TIMER menu again
to confirm or change the remaining
time.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
2 Set the ID number you want.
„ BLUE BACK
You can set the TV to automatically change
to a blue screen and mute the sound if the
signal is weak or absent, or when there is
no input from an external device.
To choose a number:
Press the 6buttons.
To move a cursor:
Press the 5 buttons.
ON:
3 Press the MENU/OK button.
This function is turned on.
OFF:
This function is turned off.
„ CHILD LOCK
You can disable the front control buttons of
the TV. When this function is set to ON, the
TV can be operated only by using the
remote control.
Use this function to prevent children from
operating the TV at their own discretion
(without parent consent).
4 Press the 6buttons to choose a TV
channel.
• The TV shows the TV programme
which the chosen TV channel is now
broadcasting.
ON:
This function is turned on.
OFF:
5 Press the blue button to set this
function to the TV channel.
This function is turned off.
n(CHANNEL GUARD) appears and the
TV channel is locked.
„ CHANNEL GUARD
When there is a TV channel you do not
want your children to watch, you can lock
out the channel. Even when a child chooses
a programme number for a locked out
channel the screen will change to blue and
display nso the channel cannot be viewed.
To cancel this function:
Press the blue button again.
n(CHANNEL GUARD) disappears and
the lock is released.
6 Press the MENU/OK button to
complete the setting.
To set this function:
1 Choose CHANNEL GUARD, then
press the number 0 (AV) button.
The menu disappears.
To view a locked TV channel:
1 Choose a programme number in
which a TV channel locked with the
number buttons or PR LIST.
The screen changes to blue and the n
(CHANNEL GUARD) appears.
• You cannot choose a locked TV
channel with the 6 buttons.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
2 Press the DISPLAY button to display
“ID NO.” (ID number input screen).
This Television is compatible with the
Progressive video signal (525P signal)
only when the component video signal
is input.
„ PIP
[Except HV-34LH21/HV-29WH21/
HV-29VH21]
3 Press the number buttons to enter the
ID number.
You can enter the Twin or PIP mode from
the menu without using the remote control.
This menu will be useful if you cannot find
the remote control around you.
The lock is temporarily released so you
can view the TV channel.
If you have forgotten the ID number:
Perform step 1 of “To set this function:” on
page 27. After confirming the ID number,
press the TV/VIDEO button to exit the menu.
• For detailed description of Twin and
PIP mode, see “Twin and PIP (picture
in picture) function” on page 15.
• When you would like to cancel the
CHANNEL GUARD function, you must
perform the operation “To set this
function” again.
1 Choose PIP, then press the MENU/OK
button.
„ AUTO SHUTOFF
You can set your TV to turn off if no signal is
received for about 15 minutes or longer
after the end of a broadcast.
2 Display Twin or PIP picture as you like.
First press the 6 button to choose an
item listed, then press the MENU/OK
button. Next press the 5 button to
choose one of options, then press the
MENU/OK button.
ON:
This function is turned on.
OFF:
This function is turned off.
• The AUTO SHUTOFF function does
not turn off the TV’s main power.
• The AUTO SHUTOFF will not work for
a VIDEO mode.
PIP/TWIN
Each time you press the 5 button, the
screen mode changes as follows:
TWIN → PIP → OFF (normal screen)
„ VIDEO-3 SETTING
Set the VIDEO-3 SETTING correctly
according to the video signal input from the
external device connected to the VIDEO-3
terminal. If this setting is incorrect, images
will not be displayed.
SUB INPUT
Each time you press the 5 button, the
input source of the sub picture changes as
follows:
VIDEO-1 → VIDEO-2 → VIDEO-3 →
VIDEO-4 → TV
VIDEO:
If a normal video signal (composite video
signal) is input.
SWAP
Each time you press the MENU/OK button,
the main picture and the sub picture will be
swapped.
COMPONENT:
If a Component video signal (Y/CB/CR
• If PIP/TWIN is selected OFF, then
SUB INPUT and SWAP disappears in
PIP menu.
signals) is input.
• For detailed connecting methods, see
“Additional preparation” on page 35.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
INSTALL menu
• To stop the AUTO PROGRAM
function, press the MENU/OK button.
„ LANGUAGE
2 After the TV channels have been
stored in the programme number list,
the EDIT menu appears.
You can choose the language you want to
use for the on-screen display from the
language list in a menu.
1 Choose LANGUAGE, then press the
MENU/OK button.
2 Press the 6 buttons to choose a
language.
3 Press the MENU/OK button to
complete the setting.
• You can proceed to edit the
programme numbers list using the
EDIT/MANUAL function. For details,
see “EDIT/MANUAL” on page 30
• If a TV channel you want to view is not
stored in the programme numbers list,
you can register it using the MANUAL
function.
The menu disappears.
„ AUTO PROGRAM
You can automatically register the TV
channels which can be received well at your
residence in the TV’s programme numbers
by performing the following.
1 Choose AUTO PROGRAM, then press
the MENU/OK button.
For details, see “EDIT/MANUAL” on
page 30.
The AUTO PROGRAM function starts.
The TV channels you receive are
automatically stored in the programme
numbers list.
• The AUTO PROGRAM function does
not store a TV channel to the
programme number 0 (AV).
• If you do not need to use the EDIT/
MANUAL function, press the MENU/
OK button to exit the EDIT menu.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
INSERT:
„ EDIT/MANUAL
This function adds a new TV channel in
the current programme numbers list by
using the CH/CC number.
The EDIT/MANUAL functions are divided
into two types: editing of the current
programme numbers (EDIT functions) and
manual registration of a TV channel you
want to view to the programme number
(MANUAL function).
DELETE:
This function deletes an unnecessary TV
Channel.
MANUAL:
This function manually registers a new
TV channel in a programme number.
CAUTION
• Using the MOVE, DELETE or INSERT
function rewrites the current programme
numbers list.
Resultingly, the programme number of
some of the TV channels will change.
• When a TV channel which has been
locked out using the CHANNEL GUARD
function, using the MANUAL function for
that TV channel cancels the CHANNEL
GUARD function.
3 Press the MENU/OK button to
complete the setting.
• For programme number PR 0, “AV”
appears in the programme numbers
list.
FUNCTIONS
MOVE
• When a TV channel has already been
registered in PR 99, using the INSERT
function deletes the TV channel.
1 Press the 6buttons to choose a TV
channel.
1 Choose EDIT/MANUAL, then press the
MENU/OK button.
2 Press the 3button to start the MOVE
function.
3 Press the 6 buttons to choose a
new programme number.
2 Follow the operation description of a
function you want to use and operate
the function.
To cancel the MOVE function:
Press the DISPLAY button.
4 Press the 2button to change the
programme number of a TV channel
to a new programme number.
MOVE:
This function changes a programme
number of a TV channel.
ID:
This function registers a Channel name
(ID) to a TV channel.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
ID
1 Press the 6buttons to choose a TV
channel.
2 Press the red button to start the ID
function.
3 Enter a channel name (ID). Press the
6 buttons to choose a character.
Press the 5buttons to move the
cursor.
To cancel the MANUAL function:
Press the DISPLAY button.
3 Press the 3button to choose the
system (sound system) for a TV
channel you want to register.
• For the sound systems in each country
or region, see the table
“BROADCASTING SYSTEMS” on
page 12.
To cancel the ID function:
Press the DISPLAY button.
4 Press the green or red button to
search for a TV channel.
4 Press the MENU/OK button to register
a channel name to a TV channel.
Scanning stops when the TV finds a TV
channel. Then the TV channel is
displayed.
DELETE
1 Press the 6buttons to choose a TV
5 Press the green or red button
repeatedly until the TV channel you
want appears.
channel.
2 Press the yellow button to delete the
TV channel.
If the TV channel reception is poor:
Press the blue or yellow button to fine-
tune the TV channel.
The TV channel is deleted from the
programme numbers list.
If you cannot hear the normal sound
even when the picture of the TV
channel appears normally:
The SYSTEM setting is wrong. Press the
3button and choose a SYSTEM that has
normal sound.
MANUAL
1 Press the 6 buttons to choose a
programme number to which you
want to register a new TV channel.
2 Press the blue button to activate the
MANUAL function.
6 Press the MENU/OK button and
register the TV channel to a
programme number.
At the right side following the CH/CC
number, the SYSTEM (sound system) of
the TV channel appears.
The normal EDIT menu is resumed.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
INSERT
Preparation:
• Find the CH/CC number
corresponding to the channel number
of the TV channel from page 33.
1 Press the 6buttons to choose a
programme number for which you will
register a new TV channel.
• When you attempt to insert the TV
channel of NTSC-M system, press
SOUND SYSTEM button to switch
SOUND SYSTEM to M, then proceed
to the next step.
2 Press the green button to start the
INSERT function.
3 Press the 6buttons to choose “CC”
or “CH” according to the CH/CC
number of the TV channel.
To cancel the INSERT function:
Press the DISPLAY button.
4 Press the Number buttons to enter the
remaining CH/CC number.
The TV shifts to registration mode. When
the registration is completed, the picture
of the TV channel appears on the
screen.
• The CH/CC number is a number
indicating the broadcast frequency to
the TV. If the TV cannot detect the TV
channel corresponding to the
broadcast frequency indicated by the
CH/CC number, a picture in the no-
signal state appears.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
CH/CC number
When you want to use the INSERT function on page 32, find the CH/CC number
corresponding to the Channel number of the TV channel from this table.
US: The US channel numbers are the channel numbers used in the United States,
Philippines, etc. CCIR: The CCIR channel numbers are the channel numbers used in the
Middle East, Southeast Asia, etc. OIRT: The OIRT channel numbers are the channel
numbers used in Eastern Europe, Russia, Vietnam, etc. AUSTRALIA: The AUSTRALIA
channel numbers are the channel numbers used in Australia, etc.
Channel
Channel
CH
US
US-2
US-3
US-4
US-5
US-6
US-7
US-8
CCIR
E2
E3
E4
E5
E6
E7
E8
E9
OIRT
R1
AUSTRALIA
AU-0
AU-1
AU-2
AU-6
AU-7
AU-8
AU-9
CC
US
CCIR
S-1
S-2
S-3
S-4
S-5
S-6
S-7
S-8
OIRT
AUSTRALIA
AU-5
CH 02
CH 03
CH 04
CH 05
CH 06
CH 07
CH 08
CH 09
CH 10
CH 11
CH 12
CH 13
CH 14
CH 15
CH 16
CH 17
CH 18
CH 19
CH 20
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
CH 30
CH 31
CH 32
CH 33
CH 34
CH 35
CH 36
CH 37
CH 38
CH 39
CH 40
CH 41
CH 42
CH 43
CH 44
CH 45
CH 46
CH 47
CH 48
CH 49
CH 50
CH 51
CH 52
CH 53
CH 54
CH 55
CH 56
CH 57
CH 58
CH 59
CH 60
CH 61
CH 62
CH 63
CH 64
CH 65
CH 66
CH 67
CH 68
CH 69
CH 70
CC 01
CC 02
CC 03
CC 04
CC 05
CC 06
CC 07
CC 08
CC 09
CC 10
CC 11
CC 12
CC 13
CC 14
CC 15
CC 16
CC 17
CC 18
CC 19
CC 20
CC 21
CC 22
CC 23
CC 24
CC 25
CC 26
CC 27
CC 28
CC 29
CC 30
CC 31
CC 32
CC 33
CC 34
CC 35
CC 36
CC 37
CC 38
CC 39
CC 40
CC 41
CC 42
CC 43
CC 44
CC 45
CC 46
CC 47
CC 48
CC 49
CC 50
CC 51
CC 52
CC 53
CC 54
CC 55
CC 56
CC 57
CC 58
CC 59
CC 60
CC 61
CC 62
CC 63
CC 64
CC 75
CC 76
CC 77
CC 78
CC 79
CC 95
CC 96
CC 97
CC 98
CC 99
R2
R6
R7
R8
R9
AU-5A
US-9
US-10
US-11
US-12
US-13
US-14
US-15
US-16
US-17
US-18
US-19
US-20
US-21
US-22
US-23
US-24
US-25
US-26
US-27
US-28
US-29
US-30
US-31
US-32
US-33
US-34
US-35
US-36
US-37
US-38
US-39
US-40
US-41
US-42
US-43
US-44
US-45
US-46
US-47
US-48
US-49
US-50
US-51
US-52
US-53
US-54
US-55
US-56
US-57
US-58
US-59
US-60
US-61
US-62
US-63
US-64
US-65
US-66
US-67
US-68
US-69
E10
E11
E12
R10
R11
R12
AU-10
AU-11
S-9
S-10
S-11
S-12
S-13
S-14
S-15
S-16
S-17
S-18
S-19
S-20
S-21
S-22
S-23
S-24
S-25
S-26
S-27
S-28
S-29
S-30
S-31
S-32
S-33
S-34
S-35
S-36
S-37
S-38
S-39
S-40
S-41
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
E21
E22
E23
E24
E25
E26
E27
E28
E29
E30
E31
E32
E33
E34
E35
E36
E37
E38
E39
E40
E41
E42
E43
E44
E45
E46
E47
E48
E49
E50
E51
E52
E53
E54
E55
E56
E57
E58
E59
E60
E61
E62
E63
E64
E65
E66
E67
E68
E69
R
S
T
U
V
W
W+1
W+2
W+3
W+4
W+5
W+6
W+7
W+8
W+9
W+10
W+11
W+12
W+13
W+14
W+15
W+16
W+17
W+18
W+19
W+20
W+21
W+22
W+23
W+24
W+25
W+26
W+27
W+28
X
Y
Z
Z+1
Z+2
R3
R4
R5
AU-3
AU-4
A-5
A-4
A-3
A-2
A-1
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
3 Press the MENU/OK button to
complete the setting.
„ TELETEXT LANGUAGE
[Except HV-34LH51/HV-29WH51]
The menu disappears.
There are five types of teletext language
groups. Set the teletext language group that
corresponds to the language of the teletext
program that you want to watch.
• Languages that are not included in the
teletext language group that you
select, the sub-titles of the teletext
program will not be displayed properly.
1 Choose TELETEXT LANGUAGE, then
press the MENU/OK button.
2 Press the 6buttons to choose a
group.
Group
Languages
Turkish, Hungarian, English,
German, French, Italian,
Spanish, Portuguese, Greek,
Swedish, Finnish
GROUP-1
Polish, Serbian, Croatian,
Slovenian, Czech, Slovak,
GROUP-2 Rumanian, Hungarian, Ger-
man, French, Italian, Swedish,
Finnish
Russian, Bulgarian, Lettish,
Lithuanian, Estonian, Ukrain-
an, Czech, Slovak, English,
GROUP-3
German, Rumanian
Arabic, Czech, Slovak. Hun-
garian, English, German,
French, Italian, Spanish, Por-
GROUP-4
tuguese, Swedish, Finnish
Farsi, Czech, Slovak. Hungar-
ian, English, German, French,
Italian, Spanish, Portuguese,
GROUP-5
Swedish, Finnish
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional preparation
„ Connecting the external
devices
Connect the devices to the TV, paying
attention to the following connection
diagram.
HV-34LH21
HV-34LH51
HV-34LH71
HV-29WH21
HV-29WH51
HV-29WH71
HV-29VH21
Before connecting anything:
• Read the manuals provided with the
devices. Depending on the devices,
the connection method may differ from
the figure. In addition, the device
settings may be changed depending
on the connection method to secure
proper operation.
(Behind the cover)
• Turn off all the devices including the
TV.
• The “Specifications” on page 40
contains the details of the VIDEO
terminals. If you are connecting a
device not listed in the following
connection diagram, see the
“Specifications” to choose the best
VIDEO terminal.
OVER
V
S
L/MONO
R
IN (VIDEO-4)
• Note that connecting cables are not
supplied.
1 VCR (composite signal)
2 VCR (S-VIDEO signal; Y/C)
3 VCR for recording (composite signal)
4 DVD player (composite signal)
5 DVD player (S-VIDEO signal; Y/C)
6 DVD player (component video signals; Y/
CB/CR)
AUDIO
R
L/MONOVIDEO
S
O
V
E
R
VIDEO-1
VIDEO-2
CR
CB
Y/VIDEO
A
UDIO
L/MONO
VIDEO-3
COMPONENT
R
R
OUTPUT
L
UDIO
VIDEO
A
7 TV game (composite signal)
8 TV game (S-VIDEO signal; Y/C)
9 Camcorder (composite signal)
0 Camcorder (S-VIDEO signal; Y/C)
- Headphones
AUDIO
L/MONO
VIDEO
S
R
OVER
VIDEO-1
VIDEO-2
CR
CB
Y/VIDEO
AUDIO
L/MONO
VIDEO-3/
COMPONENT
R
R
OUTPUT
L
VIDEO
AUDIO
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional preparation
• In the VIDEO-4 terminal, the VIDEO
jack is indicated by “V”.
Connecting methods
1 Connect the TV’s VIDEO jack and the
device’s VIDEO OUT (video output)
jack with a video cable.
2 Connect the TV’s AUDIO jacks (L/
MONO and R) and the device’s AUDIO
OUT (audio L/R output) jacks with an
audio cable.
If connecting a device to the TV with an
S-VIDEO cable:
Connect the VCR’s S-VIDEO OUT (S-
VIDEO output) connector and the TV’s S
connector with an S-VIDEO cable, instead
of connecting with a video cable.
Note that the connection with a video cable
will be ignored in case you connect a VCR
to the TV with both video cable and S-
VIDEO cable.
If the device’s sound output is in mono:
Connect the device’s AUDIO OUT jack and
the TV’s L/MONO jack with an audio cable.
Connecting devices to the
OUTPUT terminal
The signals of the images and sound you
are currently viewing with this TV are output
through the OUTPUT terminal. By
connecting a VCR to the OUTPUT terminal,
you can record the currently shown image
and sound to that VCR. To do this, connect
the VCR and OUTPUT terminal following
the steps below.
If connecting a DVD player to the TV with
a component video cable.
Connect three jacks (Y/VIDEO, CB and CR)
in the VIDEO-3 terminal and the DVD
player’s COMPONENT (component video
output) jacks with a component video
cables, instead of connection with a video
cable. Then set the VIDEO-3 SETTING to
COMPONENT, according to“VIDEO-3
SETTING” on page 28.
1 Connect the VIDEO jack in the
OUTPUT terminal and the VCR’s
VIDEO IN (video input) jack with a
video cable.
• This Television is compatible with the
Progressive video signal (525P signal)
only when the component video signal
is input.
If you have a DVD player that outputs
Progressive video signals (525P) as a
component video signal, then by
attaching the device to the television
with a component video cable you can
see the actual images that are
2 Connect the AUDIO jacks (L and R) in
the OUTPUT terminal and the VCR’s
AUDIO IN (audio L/R input) jacks with
an audio cable.
• When you turn off the TV, the signals
from the OUTPUT terminal are also
turned off.
• The component signals input from the
VIDEO-3/COMPONENT terminal
cannot be output through the OUTPUT
terminal.
recorded on a DVD disc as an original
image source.
Connecting Headphones
If connecting a device to the VIDEO-3/
COMPONENT terminal with a video
cable.
Connect the TV’s Y/VIDEO jack and the
device’s VIDEO OUT (video output) jack
with a video cable.
Connect the headphones with a stereo
mini jack (of 3.5 mm in diameter) to the
Headphone jack at the TV front panel.
Then set the VIDEO-3 SETTING to VIDEO
according to “VIDEO-3 SETTING” on
page 28.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If a problem arises while you are using the TV, please read this “Troubleshooting” well
before you request having the TV repaired. You may be able to fix it easily by yourself. For
example, if the AC plug is disconnected from the AC outlet, or the TV aerial has problems,
you may think there is a problem with the TV itself.
Important:
• This Troubleshooting guide only covers problems whose causes are not easy to
determine. If a question arise when you are operating a function, read the page(s)
corresponding to the operation of the function well, not this Troubleshooting guide.
• After you have followed the Troubleshooting description or the operating description of
the functions concerned without any success, remove the AC plug from the AC outlet
and request a repair of your TV. Do not attempt to repair the TV by yourself or remove
the rear cover of the TV.
• If the TV or aerial receives interference
„ If you cannot turn on the TV
from the other devices, stripes or noise
may appear in the picture. Move such
device as an amplifier, personal
computer, or a hair drier that can
cause interference away from your TV,
or try changing its location. If the aerial
suffers interference from a radio tower
or high-voltage wire, please contact
your local dealer.
• If the TV receives interferences from
signal reflecting from mountains or
building, double-pictures (ghosting) will
occur.
Try to change the aerial’s direction or
replace the antenna with the one with
better directionality.
• Are your COLOUR SYSTEM settings
for the TV channels correct? Follow
the description “COLOUR SYSTEM
button” on page 11 to try to solve the
trouble.
• Is the AC plug connected to the AC
outlet?
• Is the POWER lamp lit? If not, press
the Main power button.
„ No picture/No sound
• Have you chosen a TV channel whose
reception is extremely bad? In this
case, the BLUE BACK function will be
activated, the entire screen becomes
blue, and the sound is muted. In spite
of this, if you want to view the TV
channel, follow the description “BLUE
BACK” on page 27 to try to change the
BLUE BACK function setting to OFF.
• Are your SOUND SYSTEM settings for
the TV channels correct?
Follow the description “SOUND
SYSTEM button” on page 11 to try to
solve the trouble.
„ Poor picture
• Has COLOUR or BRIGHT been
controlled properly? Follow the
description “Adjusting the picture” on
page 20 to try to adjust them properly.
• Videotaping teletext is not
• If noise totally obscures the picture
(snow), the aerial or aerial cable may
have trouble. Check the following to try
to solve the trouble:
Has the TV and aerial been connected
properly?
Has the aerial cable been damaged?
Is the aerial pointed to the right
direction?
recommended because it may not
record correctly.
Is the aerial itself faulty?
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
• When a white and bright still image
(such as a white dress) is displayed on
the screen, the white part may look as
if it were coloured.
It is a phenomenon unavoidable due to
the nature of the picture tube itself, and
not due to a TV failure.
• When you are viewing a teletext
programme, you cannot operate the
menus.
Press the TV/VIDEO button to return
the teletext programme to the ordinary
TV programme to try operating the
menus.
When the picture disappears from the
screen, the unnatural colours will also
disappear.
• When viewing images from
commercially available video software
products, or videos from videotapes
which have been recorded improperly,
the top of the image may be distorted.
This is due to the condition of the video
signal, and not because of
• Is the CHILD LOCK function set to
ON? If the CHILD LOCK function is set
to ON, you cannot operate the TV with
the front control buttons of the TV.
Follow the description “CHILD LOCK”
on page 27 to try to set the CHILD
LOCK function to OFF.
• If the TV operation becomes disabled
suddenly, press the Main power button
on the TV and turn off the main power.
Try to press the Main power button
again to turn on the main power. If the
TV returns to a normal state, it is not a
failure.
malfunction.
„ Poor sound
• Have you adjusted BASS or TREBLE
properly? If not, follow the description
“Adjusting the sound” on page 25 to try
to adjust them properly.
• The following functions do not operate
when receiving Progressive video
signal (525P signal).
• When the TV channel reception is
poor, it can be hard to hear the stereo
or bilingual sound. In this case, follow
the description “STEREO / I•II” on
page 25 to hear the sound more easily
by changing it to a mono sound.
Remote control function:
PIP, MULTI, FREEZE and STROBE
button.
MENU function:
TINT and PULL DOWN
„ Other concerns
„ Operation disabled
• When the AUTO SHUTOFF function
operates, the TV is automatically
turned off.
• Have the batteries of the remote
control become exhausted?
Follow the description “Putting the
batteries into the remote control” on
page 4 and replace them with new
batteries to try solve the problem.
• Have you attempted to use the remote
control at the sides or rear of the TV or
at a location more than seven meters
apart from the TV location? Operate
the remote control in the front of your
TV or a location less than seven
meters from your TV to try to solve the
problem.
If the TV is turned off suddenly, try to
press the POWER button to turn on
the TV once again. At this time, if the
TV resumes a normal state, there is no
problem.
• If you bring a magnetized device such
as a speaker near to your TV, a picture
may be warped or unnatural colours
appear at the corners of the screen. In
this case, keep the device apart from
your TV. If the speaker causes such
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
phenomena, use the magnetic-
shielded speaker instead.
• A picture may be tilted due to the
influence of the earth’s magnetism. In
this case, use the “PICTURE TILT” on
page 23 to complete the tilt.
• It takes a short period of time from the
time an operation such as changing
channels is performed until an image is
displayed. This is not a malfunction.
This is the time required for the image
to stabilize before it can be displayed.
• The TV may emit a crackling sound
due to a sudden change in
temperature. It does not matter if a
picture or sound does not show any
abnormality. If you hear crackling
sounds frequently while you are
viewing the TV, other causes may be
assumed.
For precautionary purposes, request
your service technician to inspect it.
• Touching the screen may cause you
feel a slight electric shock due to its
static electricity.
It is an unavoidable phenomenon due
to the construction of the picture tube.
It is not a problem with the TV.
You can rest assured that this static
discharge does not have harmful
influence over the human body.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Broadcasting systems
Colour systems
B, G, I, D, K, K1, M
PAL, SECAM, NTSC3.58/4.43MHz
Channels and frequencies
VHF low channel (VL) =46.25 to 168.25 MHz
VHF high channel (VH) =175.25 to 463.25 MHz
UHF channel (U)
=471.25 to 863.25 MHz
• Receives cable channels in mid band (X to Z+2, S1 to S10), super band (S11
to S20) and hyper band (S21 to S41).
Sound-multiplex systems
Teletext systems
A2 (B/G), NICAM (B/G, I, D/K) system
FLOF(Fastext), WST(World Standard Text)
[Except HV-34LH51/HV-29WH51]
Languages displayed by
teletext
Please see the table in the description “TELETEXT LANGUAGE” on page 34.
[Except HV-34LH51/HV-29WH51]
Power requirements
Audio output
AC 110 to 240V, 50/60Hz
Rated Power output: 10W + 10W
VIDEO-1 terminal
RCA connector × 3, S-VIDEO connector × 1
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
VIDEO-2 terminal
RCA connector × 3
• Video input and Audio L/R inputs are available.
VIDEO-3/COMPONENT
RCA connector × 5 terminal
• Video input/Component video (Y/CB/CR) input and Audio L/R inputs are
available.
• Progressive video signal (525P signal) input is available.
VIDEO-4 terminal
OUTPUT terminal
RCA connector × 3, S-VIDEO connector × 1
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
RCA connector × 3
• Video output and Audio L/R outputs are available.
Headphone jack
Accessories
Stereo mini-jack (3.5 mm in diameter)
Remote control unit × 1
RM-C1350 [HV-34LH71/HV-29WH71]
RM-C1351 [HV-34LH21/HV-29WH21/HV-29VH21]
RM-C1353 [HV-34LH51/HV-29WH51]
AA/R6 dry cell battery × 2
Speakers
34” model: (12cm × 5cm) × 2
29” model: (13cm × 6.5cm) × 2
* 34” model: HV-34LH21/HV-34LH51/HV-34LH71
29” model: HV-29WH21/HV-29WH51/HV-29WH71/HV-29VH21
Design and specifications subject to change without notice.
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or
demonstration purpose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of
the original picture sources, as this constitutes an infringement of copyright.
This TV does not conform to the PAL-D Chinese broadcasting system.
VICTOR COMPANY OF JAPAN, LIMITED
40
Download from Www.Somanuals.com. All Manuals Search And Download.
|