COLOUR TELEVISION
AV-28WFT1EI
CONTENTS
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . 2
PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
T-V LINK FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . 7
BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 8
REMOTE CONTROL BUTTONS AND FUNCTIONS . 11
MENU OPERATION . . . . . . . . . . . . . . . . . . . . . . . . 16
PICTURE SETTING. . . . . . . . . . . . . . . . . . . . . . . . . 17
PICTURE FEATURES. . . . . . . . . . . . . . . . . . . . . . . 18
SOUND SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . 20
EXT SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
INSTALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
DEMO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
ADDITIONAL MENU OPERATIONS . . . . . . . . . . . . 30
ADDITIONAL PREPARATION. . . . . . . . . . . . . . . . . 32
TV BUTTONS AND PARTS. . . . . . . . . . . . . . . . . . . 34
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . 35
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . Back cover
INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for buying this
colour television.
To make sure your fully understand how to use your new TV, please read this manual thoroughly before you begin.
6$)(7<#35(&$87,216
■ :DUQLQJ
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EX-
POSE THIS APPLIANCE TO RAIN OR MOISTURE.
■
&DXWLRQ
TO ENSURE PERSONAL SAFETY, OBSERVE THE FOL-
LOWING RULES REGARDING THE USE OF THIS UNIT.
1 Operate only from the power source specified (AC 220 –
240 V, 50 Hz) on the unit.
2 Avoid damaging the AC plug and power cord.
3 Avoid improper installation and never position the unit
where good ventilation is unattainable.
When installing this television, distance recommendations
must be maintained between the floor and wall, as well as
instalment in a tightly enclosed area or piece of furniture.
Please adhere to the minimum distance guidelines shown
for safe operation.
15 cm
10 cm
10 cm
15 cm
4 Do not allow objects or liquid into the cabinet openings.
5 In the event of a fault, unplug the unit and call a service
technician. Do not attempt to repair it yourself or remove
the rear cover.
6 When you don’t use this TV set for a long period of time, be
sure to disconnect the power plug from the AC outlet.
7 Do not hold the front panel door when moving the TV, if you
do you may break it.
How To Replace The Fuse
Open the fuse compartment
with a blade screwdriver, and
replace the fuse.
Fuse
5
Download from Www.Somanuals.com. All Manuals Search And Download.
■
*XLGHOLQHV#IRU#6DIH#2SHUDWLRQ
This equipment has been designed and manufactured to comply with international safety standards. However, as with any elec-
trical appliance, care must be taken to ensure optimal results and operational safety.
• Before attempting to use this equipment, read the operating instructions thoroughly.
• Ensure that all electrical connections (including the mains plug, extension leads, etc.) have been made in accordance with the
manufacturer’s instructions.
• If ever in doubt about the installation, operation or safety of this equipment, consult your dealer.
• Handle all glass panels or covers with care.
• Never operate this equipment if it appears damaged or operates abnormally. Turn the power off, disconnect the main power
plug and consult your dealer.
• Never remove any affixed panels or covers. Doing so may result in electrical shock.
• Never leave this equipment operating unattended unless otherwise specifically stated that it is designed to do so or in standby
mode. Only use the designated power switch to turn off the power and ensure that all potential users are instructed how to do
so. Make special arrangements for infirm or handicapped persons.
• Never watch TV while operating a motor vehicle. It is illegal to watch TV while driving.
• Never listen to headphones at high volume. Doing so may damage your hearing.
• Never obstruct the ventilation of this equipment. Doing so may cause overheating and result in a malfunction or damage.
• Never use makeshift stands or attempt to affix legs with wood screws. When using a manufacturer’s approved stand or legs,
use only the fixtures provided and follow the installation instructions.
• Never allow this equipment to be exposed to rain or moisture.
• Never allow anyone, especially children, to insert anything into an opening in the case. Doing so may result in a fatal electrical
shock.
• Never guess or take chances with electrical equipment of any kind. It is better to be safe than sorry.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
35(3$5$7,21
■ &RQQHFWLQJ#WKH#$HULDO#DQG#9&5
→
→
→
If connecting a VCR, follow A
If not connecting a VCR, follow 1
B
C
2 .
D .
AC Outlet
(AC 220 - 240 V,
50 Hz)
→
*1: To operate T-V LINK functions, a T-V LINK compatible
VCR must be connected to the EXT-2 terminal on the TV.
For details about T-V LINK functions, see “T-V LINK
FUNCTIONS” on page 7.
VHF/UHF Aerial
Note:
• For further details, refer to the manuals provided with the
devices to be connected.
Power
Cord
• The connecting cables are not provided.
75-ohm
Coaxial
Cable
• A video can be viewed from the VCR without performing
C . For details, refer to your VCR instruction manual.
EXT-2
EXT-3
*1
S
S
• To connect additional external devices, please see “AD-
DITIONAL PREPARATION” on page 32.
L
R
EXT-1
AUDIO OUT
• To connect external speakers and audio system, please
see “Connecting Speakers/Amplifier” on page 33.
Aerial
Plug
• When a decoder is connected to a T-V LINK compatible
VCR, set the DECODER (EXT-2) function to ON. For de-
tails, see “Using the DECODER (EXT-2) function” on
page 30. Otherwise, you will not be able to view scram-
bled channels.
21-pin SCART Cable
Aerial Plug
75-ohm Coaxial
Cable
VCR
To Aerial
Input
Aerial Plug
To Aerial
Output
AV IN/OUT
Terminal
■ 3XWWLQJ#%DWWHULHV#LQWR#WKH#5HPRWH#&RQWURO
Use two AAA/R03 dry cell batteries.
Insert the batteries from the ó end, making sure the ô and ó
polarities are correct.
To open the battery compartment, slide the door downwards
and lift off. Replace the door by sliding it upwards until it is se-
cure.
Note:
• Follow the warnings printed on the batteries.
• Battery life is about six months to one year, depending on
your frequency of use.
• If the remote control does not work properly, replace the
batteries.
• The batteries we supply are only for setting up and test-
ing your TV, please replace them as soon as necessary.
• Always use good quality batteries.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
■ ,QLWLDO#6HWWLQJV
When the TV is first turned on, it enters the initial setting
mode, and the JVC logo is displayed. Follow the instructions
on the on-screen display to make the initial settings.
1
Press the Main power button on the TV.
The Power lamp lights red (for power on), then green (for
TV on) and the JVC logo is displayed.
Note:
• If the power lamp stays red and does not change to
green:
Main power button
Your TV is in the standby mode. Press the
(Standby) button on the remote control to turn your
TV on.
=
Power lamp
• The JVC logo does not appear when your TV has
been turned on once.
In this case, use the “LANGUAGE” and “AUTO PRO-
GRAM” functions to make the initial settings. For de-
tails, see “INSTALL” on page 25.
1
4
7
2
5
8
0
3
6
9
2 Press the
button.
The LANGUAGE menu appears.
3
AV
MENU
OK
P
TV
P
3 Press the ë buttons to choose ENG-
LISH.
English is set for the on-screen display description.
RM-C51
TV
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
4 Press the
button to start the AUTO
PROGRAM function.
3
Note:
• When you TV can detect the TV channel name from
the TV channel broadcast signal, it automatically
registers the TV channel name (ID) to the Pro-
gramme number (PR) in which the TV channel has
been registered.
The AUTO PROGRAM menu appears and received TV
channels are automatically registered in the Programme
numbers (PR).
• If a TV channel you want to view is not set to a Pro-
gramme number (PR), manually set it using the
MANUAL function. For details, see “EDIT/MANUAL”
on page 26.
• The TV channel is not registered in Programme
number PR 0 (AV). When you want to register a TV
channel to PR 0 (AV), manually set it using the MAN-
UAL function. For details, see “EDIT/MANUAL” on
page 26.
To cancel the AUTO PROGRAM function:
Press the
button.
4
5 After the TV channels have been regis-
tered in the Programme numbers (PR),
the EDIT menu appears.
You can proceed to edit the Programme numbers (PR)
using the EDIT/MANUAL function. For details, see “ED-
IT/MANUAL” on page 26.
When not using the EDIT/MANUAL function:
If you do not need to use the EDIT/MANUAL function,
go to the next step.
6 Press the
button to display the T-V
3
LINK menu.
7 Operate the T-V LINK menu according
to the type of a VCR connected to the
EXT-2 terminal.
When a T-V LINK compatible VCR is not con-
nected:
Press the
The T-V LINK menu disappears.
button to exit the T-V LINK menu.
4
When a T-V LINK compatible VCR is connected:
Follow the operating procedure “Downloading the data
to VCR” on page 30 to transmit the Programme number
(PR) data.
8 Now, the initial settings are complete,
and you can watch the TV.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
709#/,1.#)81&7,216
When a T-V LINK compatible VCR is connected to the EXT-
2 Terminal on the TV, it is easier to set up the VCR and to
Note:
view videos. T-V LINK uses the following features:
• Operation via the TV is not possible.
• Generally, the VCR cannot record a TV channel that can-
not be received properly by the VCR’s tuner, even though
you can view that TV channel on the TV. However, some
VCRs can record a TV channel by using the TV’s output
if that channel can be viewed on the TV, even though the
TV channel cannot be received properly by the VCR’s
tuner. For details, refer to your VCR instruction manual.
To use T-V LINK functions:
A T-V LINK compatible VCR is necessary.
The VCR must be connected to the EXT-2 terminal on the TV
by a fully wired SCART cable.
Note:
• A “T-V LINK compatible VCR” means a JVC VCR with the
T-V LINK logo or a VCR with one of the following logos.
However, these VCRs may support some or all of the fea-
tures described below. For details, refer to your VCR in-
struction manual.
■ 79#$XWR#3RZHU#2Q29&5#
,PDJH#9LHZ
When the VCR starts playing, the TV automatically turns on
and the images from EXT-2 terminal are displayed on the
screen.
When the VCR menu is operated, the TV automatically turns
on and the images from EXT-2 terminal are displayed on the
screen.
“Q-LINK” (a trademark of Panasonic Corporation)
“Data Logic” (a trademark of Metz Corporation)
“Easy Link” (a trademark of Phillips Corporation)
“Megalogic” (a trademark of Grundig Corporation)
“SMARTLINK” (a trademark of Sony Corporation)
■ 3UH0VHW#'RZQORDG
Note:
• This function does not operate if your TV’s main power is
turned off. Set your TV’s main power to on (standby
mode).
Download the registered data on the TV channels from the TV
to the VCR.
The Preset Download function automatically begins when the
initial setting is complete or whenever the AUTO PROGRAM
or EDIT/MANUAL operations are performed.
Note:
• This function can be operated via VCR operation.
When “FEATURE NOT AVAILABLE” is displayed:
If “FEATURE NOT AVAILABLE” is displayed, the download
was not performed correctly. Before trying to download again,
ensure the following:
• The VCR power is turned on.
• The VCR is T-V LINK compatible.
• The VCR is connected to the EXT-2 terminal.
• The SCART cable is fully wired.
■ 'LUHFW#5HF
“What You See Is What You Record”
You can record to VCR the images that you are currently
viewing on TV by a simple operation.
For details, read the manual for your VCR.
Operate via the VCR. “VCR IS RECORDING” is displayed.
In the following conditions, the VCR will stop recording if
the TV is turned off, if the TV channel or input is switched,
or if the menu is displayed on the TV:
• When recording images from an external device connected
to the TV.
• When recording a TV channel after it has been unscrambled
on a decoder.
• When recording a TV channel by using the TV’s output be-
cause that TV channel cannot be properly received on the
VCR’s tuner.
:
Download from Www.Somanuals.com. All Manuals Search And Download.
%$6,(5$7,21
■ 7XUQ#WKH#0DLQ#SRZHU#RQ
Press the Main power button on the TV.
The Power lamp lights red and your TV is in the standby mode.
Note:
• If the Power lamp lights green, the TV is already on.
To turn the Main power off:
Press the Main power button again.
The Power lamp goes off.
Note:
• To save energy, turn the main power off if you are not us-
ing the TV for a long period of time.
Main power button
Power lamp
■ 7XUQ#WKH#79#RQ#IURP#VWDQGE\#PRGH
Press the
button, the
buttons.
(Standby) button, the
=
4
buttons or the Number
ë
The Power lamp lights red to green and your TV will be turned on.
1
4
7
2
5
8
0
3
6
9
To turn the TV off:
Number
buttons
Press the
(standby) button again.
=
The Power lamp changes from green to red and the TV enters
standby mode.
AV
■ &KRRVH#D#79#FKDQQHO
Choose a Programme number (PR) in which the desired Pro-
gramme TV channel has been set.
MENU
OK
P
TV
Use the ë buttons:
Press the ë buttons to choose the desired Pro-
gramme number (PR).
Use the Number buttons:
Enter the desired Programme number (PR) with the
Number buttons.
P
Example
→
• PR12
press ~ and Ÿ .
• PR6 → press ¤ .
Use the PR LIST:
1 Press the 9 (Information) button to
RM-C51
display the PR LIST.
TV
;
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
Use the ë buttons:
Press the ë buttons to choose an EXT terminal
2 Press the ì and ë buttons to choose a
Programme number (PR). Then press the
button.
3
Use the PR LIST:
1 Press the
(Information) button to
9
Note:
display the PR LIST.
• For Programme numbers (PR) with the CHILD
LOCK function set, the (CHILD LOCK) mark is
displayed next to the Programme number (PR) in
the PR LIST
ì
ë
2 Press the
and
buttons to choose an
@
EXT terminal. Then press the
.
button
3
• You cannot use the ë buttons to choose a Pro-
gramme number (PR) with the CHILD LOCK fun-
tion set.
Note:
• The EXT terminals are registered after the Pro-
gramme number PR 99.
• Even if you try to choose a Programme number
• You can choose a video input signal from the S-VID-
EO signal (Y/C signal) and regular video signal
(composite signal). For details, see “K(S-VIDEO
input)” on page 21.
(PR) with the CHILD LOCK function set, the
@
(CHILD LOCK) mark will appear, and you cannot
watch the TV channel. To watch the TV channel,
see “CHILD LOCK” on page 23.
• If you do not have a clear picture or no colour ap-
pears, change the colour system manually. See
“COLOUR SYSTEM” on page 18.
• If the picture is tilted, correct it. See “PICTURE
TILT” on page 19.
•
When choosing an EXT terminal with no input signal,
the EXT terminal number becomes fixed on the screen.
■ $GMXVW#WKH#YROXPH
• This TV set has a function which can automatically
change over the input according to a special signal
output from an external device.(The EXT-4 terminal
does not support it.)
ì
Press the
ume.
buttons to adjust the vol-
The Volume indicator appears and the volume changes as
you press the C buttons.
To return to a TV channel:
ë
buttons or the Number but-
Press the 4 button, the
tons.
■ :DWFK#LPDJHV#IURP#H[WHUQDO#
To use the Programme number PR 0 (AV):
When the TV and VCR are connected only by the Aerial
cable, choosing the Programme number PR 0 (AV) al-
lows you to view images from the VCR. Set the VCR RF
channel to the Programme number PR 0 (AV) manually.
For details, see “EDIT/MANUAL” on page 26.
GHYLFHV
Choose an EXT terminal to which the desired external device
has been connected.
Use the
button:
A
Pressing the
button changes the choice as follows:
A
Press the
button to choose an EXT terminal.
A
Pressing the
button changes the choice as follows:
A
TV mode
PR 0
EXT modes
EXT-1
EXT-2
EXT-3
TV mode
EXT modes
Programme
numbers
Programme
numbers
PR 1 – PR 99
PR 1 – PR 99
EXT-1
EXT-4
EXT-2
EXT-3
EXT-4
Note:
• The VCR RF channel is sent as the RF signal from
the VCR.
• Also refer to your VCR instruction manual.
<
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
■ 2SHUDWLQJ#ZLWK#WKH#EXWWRQV#RQ#WKH#79
1 Press the P B buttons to turn the
TV on from standby mode.
2
Press the P
B
buttons to choose a
Programme number (PR) or an EXT ter-
minal.
(Behind the front cover)
3 Press the D (Volume) button and the
C buttons to adjust the volume.
1 Press the D (Volume) button.
The volume level indicator appears.
2 Press the C buttons while the volume lev-
el indicator is displayed.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
5(027(#&21752/#%877216#$1'#)81&7,216
1 0XWLQJ#%XWWRQ
You can turn the sound off instantly.
Press the
sound. Pressing the
restores the previous Volume level.
(Muting) button to turn off the
>
(Muting) button again
>
1
4
7
2
5
8
0
3
6
9
2 1XPEHU#%XWWRQV
You can choose a Programme number (PR) by
entering the Programme number.
AV
Example:
→
• PR12
press ~ and Ÿ .
→
• PR6
press ¤ .
MENU
OK
P
You can also press the
EXT terminal.
button repeatedly to choose an
A
TV
3 =220#%XWWRQ
You can change the screen size according to the picture as-
pect ratio. Choose the optimum one from the following ZOOM
modes.
P
AUTO:
For any picture format except Normal Picture (4:3 Aspect Ra-
tio), the picture will be automatically displayed in the optimum
screen size.
For Normal Picture (4:3 Aspect Ratio), the picture is displayed
in accordance with the ZOOM mode set in the 4:3 AUTO AS-
PECT menu. For details, see “4:3 AUTO ASPECT” on
page 18.
Note:
• AUTO may not function properly with poor signal quality.
In this case, choose an optimum ZOOM mode manually.
• This TV supports WSS (wide-screen signals). When
broadcasts with WSS are received with the ZOOM mode
set at AUTO, the most suitable ZOOM mode is automati-
cally chosen according to the WSS received.
RM-C51
• With the ZOOM mode set to AUTO, if the special signal
from an external device such as a VCR or DVD etc. is re-
ceived the ZOOM mode automatically changes to 16:9
ZOOM. (Except if the external source is connected to
EXT-4.)
TV
How to open the cover
REGULAR:
Use to view a normal picture (4:3 aspect ratio) in its original
shape.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL BUTTONS AND FUNCTIONS
ë
PANORAMIC:
This mode stretches the left and right sides of a normal pic-
ture (4:3 Aspect Ratio) to fill the screen, without making the
picture appear unnatural.
2 Press the
buttons to choose a ZOOM
button.
mode. Then press the
3
The picture expands and the chosen ZOOM mode is dis-
played in about 5 seconds.
Note:
• You can pre-set a ZOOM mode for the normal pic-
ture. See “4:3 AUTO ASPECT” on page 18.
Note:
$GMXVWLQJ#WKH#YLVLEOH#DUHD#RI#WKH#SLF0
• The top and bottom of the picture are slightly cut off.
WXUH
If subtitles or the top (or bottom) of the picture are cut off, ad-
just the visible area of the picture manually.
14:9 ZOOM:
This mode zooms up the Wide Picture (14:9 Aspect Ratio) to
the upper and lower limits of the screen.
1 Press the
button.
5
The ZOOM menu appears.
2 Press the
button to display the ZOOM
3
mode indication.
Indicator is displayed.
16:9 ZOOM:
This mode zooms up the Wide Picture (16:9 Aspect Ratio) to
the full screen.
ë
3 While it is displayed, press the
buttons
to adjust the visible area vertically.
16:9 ZOOM SUBTITLE:
This mode zooms up the Wide Picture (16:9 Aspect Ratio)
with subtitles to the full screen.
Note:
• You cannot adjust the visible area in REGULAR or
FULL mode.
4 +<3(5#6281'#%XWWRQ
You can enjoy sounds with a wider ambience.
Press the
the HYPER SOUND function on or off.
(HYPER SOUND) button to turn
ò
FULL:
This mode uniformly stretches the left and right sides of a nor-
mal picture (4:3 aspect ratio) to fill the wide TV screen.
Note:
• For 16:9 aspect ratio pictures that have been squeezed
into a normal picture (4:3 aspect ratio), use the FULL
mode to restore the picrure to its original shape.
Note:
• The HYPER SOUND function does not work properly with
&KRRVH#WKH#=220#PRGH
1 Press the 5 button to display the ZOOM
mono sound.
• The HYPER SOUND lamp lights while the HYPER SOUND
function is in use.
menu.
• The HYPER SOUND function can be also turned on or off
by using the SOUND SETTING menu. For details, see
“HYPER SOUND” on page 20.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL BUTTONS AND FUNCTIONS
5 #,QIRUPDWLRQ#%XWWRQ
You can display the PR LIST or the Current Time on the
screen.
8 6WDQGE\#%XWWRQ
Press the
on or off.
(Standby) button to turn the TV
=
Press the
Pressing the
play as follows:
(Information) button.
(Information) button changes the dis-
9
9
When the TV is turned on, the power lamp changes from red
to green.
9 &RORXU#%XWWRQV
The colour buttons are used for the teletext operations or the
menu operations. For details, see “~ Teletext Control But-
tons and VCR/(/DVD Switch” on page 14 or “MENU OPER-
ATION” on page 16.
0 2.#%XWWRQ
The
button is used to operate menus. For details, see
3
“MENU OPERATION” on page 16.
ë
-
#%XWWRQV
You can choose a Programme number (PR) or an EXT termi-
nal.
Current time
No indication
ë
Press the
buttons to choose an Pro-
gramme number (PR) or an EXT terminal.
The
buttons are also used to operate menus.
ë
Note:
For details, see “MENU OPERATION” on page 16.
• You can choose Programme numbers (PR) or EXT termi-
nals with the PR LIST. For details, see “Use the PR LIST:”
on page 8.
= 9&52'9'# &RQWURO# %XWWRQV# DQG
9&52(2'9'#6ZLWFK
These buttons can be used to operate a JVC brand VCR or
DVD player. Pressing a button which has the same appear-
ance as a button on the original remote control of the VCR or
DVD player makes the function work in the same way as the
button on the original remote control.
• This TV uses teletext data to set the current time. If the TV
has not received a TV channel that has teletext pro-
grammes since it was turned on, the time display is blank.
To view the current time, choose a TV channel that has
teletext programmes. The time will still be displayed as
long as you do not turn off the TV, even if you choose oth-
er TV channels.
• When watching videos, an incorrect current time is some-
1 Set the VCR/(/DVD Switch to the VCR or
times displayed.
DVD position.
VCR:
• The
(Information) button is also used to operate
9
menus. For details, see “MENU OPERATION” on
When you are operating the VCR, set the switch to the
VCR position.
page 16.
DVD:
6 79#%XWWRQ
You can return to a TV channel instantly.
When you are operating the DVD player, set the switch
to the DVD position.
Press the
button.
4
(Text):
(
The TV returns to the TV mode and a TV channel appears.
When you are viewing Teletext programmes, set the
switch to the (Text) position.
(
Note:
• The
button is also used to operate menus. For details,
see “MENU OPERATION” on page 16.
4
2 Press the VCR/DVD Control Button to con-
trol your VCR or DVD player.
7 ì#%XWWRQV
You can adjust the volume.
Note:
• If your device is not made by JVC, these buttons
cannot be used.
• Even if your device is made by JVC one or more of
these buttons may not work, dependent on the de-
vice you are using.
Press the ì buttons to adjust the sound.
Note:
• You can use the
buttons to choose a TV channel
B
• The ì buttons are also used to operate menus. For de-
tails, see “MENU OPERATION” on page 16.
the VCR will receive or choose the chapter the DVD
player plays back.
• Some models of DVD player use the
buttons for
B
operation of both the Fast forward/backward func-
tions and for choosing the chapter. In this case, the
1/¡ buttons do not work.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL BUTTONS AND FUNCTIONS
■ ~ #7HOHWH[W#&RQWURO#%XWWRQV#DQG#9&52(2'9'#6ZLWFK
3 Press and hold down
button.
ö
%DVLF#RSHUDWLRQ
You can view two types of teletext broadcasts on the TV:
FLOF (Fastext) and WST (World Standard Text).
The four page numbers blink white to indicate that they
are stored in memory.
1 Choose a TV channel with a teletext broad-
cast.
To call up a stored page:
1 Press the ù button to engage the List
2 Set the VCR/(/DVD switch to the
(Text)
mode.
(
position.
2 Press a colour button to which a page has
been assigned.
3 Press : (Text) button to display the
To exit the List mode:
Press the ù button again.
teletext.
Pressing : (Text) button changes the mode as fol-
lows:
+ROG
You can hold a teletext page on the screen for as long as you
want, even while several other teletext pages are being re-
ceived.
Press the û button.
TV mode
Text mode
Hold indication
4 Choose a teletext page by pressing the
ë
buttons, Number buttons or Colour
buttons.
To cancel the Hold function:
To return to the TV mode:
Press û button again.
Press the
button or
(Text) button.
:
4
6XE0SDJH
Note:
Some teletext pages include sub-pages that are automatically
displayed.
• If you have trouble receiving teletext broadcasts,
consult your local dealer or the teletext station,
You can hold any sub-page, or view it at any time.
• In the Text mode, the ZOOM mode is fixed to the
FULL mode.
1 Press the õ button to operate the Sub-
• No menu operations are possible when viewing a
teletext programme.
page function.
2 Press the Number buttons to enter a sub-
page number.
8VLQJ#WKH#/LVW#0RGH
You can store the numbers of your favourite teletext pages in
memory and call them up quickly using the colour buttons.
Example:
• 3rd sub-page → press ) , ) , ) and 3 .
To store the page numbers:
To cancel the Sub-page function:
Press the õ button again.
1 Press
button to engage the List mode.
ù
The stored page numbers are displayed at the bottom of
the screen.
Note:
• You can also choose a sub-page by pressing the
red or green button.
2 Press a Colour button to choose a posi-
tion. Then press the Number buttons to en-
ter the page number.
1
4
7
2
5
8
0
3
6
9
AV
47
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL BUTTONS AND FUNCTIONS
5HYHDO
Some teletext pages include hidden text (such as answers to
a quiz).
You can display the hidden text.
Each time you press the ø button, text is hid-
den or revealed.
6L]H
You can double the height of the teletext display.
Press the ÷ button.
,QGH[
You can return to the index page instantly.
Press ú button.
FLOF (Fastext)/WST (World Standard Text):
Returns to page 100 or a previously specified page.
List mode:
Returns to the page number displayed in the lower left area of
the screen.
&DQFHO
You can search for a teletext page while watching TV.
1 Press the Number button to enter a page
number, or press a Colour button.
The TV searches for a teletext page.
2 Press ü button.
The TV programme appears. When the TV finds the
teletext page, its page number appears in the upper left
of the screen.
3 Press ü button to return to a teletext
page when the page number is on the
screen.
Note:
• The TV mode cannot be resumed by pressing the
button. The TV programmes are temporarily dis-
played instead of the teletext programme. To return
ü
to TV mode press the
button.
4
48
Download from Www.Somanuals.com. All Manuals Search And Download.
0(18#23(5$7,21
This TV has a number of functions you can operate using
menus. To fully utilize all your TV’s functions, you need to un-
derstand the basic menu operating techniques fully.
1 Press the
button to display the
MENU (main menu).
3
The MENU (main menu) appears. In it, the titles of the
menus are displayed.
2 Press the
buttons to choose a
menu title, and press the 3 button.
ë
The menu appears.
3 Operate the menus according to the
operation description of each function.
Note:
• For details, refer to the operation descriptions of
each function described for each menu which fol-
lows this “MENU OPERATION”.
• The display appearing at the bottom of a menu indi-
cates a button on the remote controller you can use
when you operate a chosen function.
4 Press
button to complete the set-
3
ting.
The menu disappears.
To return to the previous menu:
Press
(information) button.
9
To exit a menu instantly:
Press the 4 button.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
3,&785(#6(77,1*
Note:
• You can change the HUE setting (picture hue) only
when the colour system is NTSC 3.58 or NTSC 4.43.
To return to the default settings in each TINT
mode:
Press the blue button.
Returns the picture settings in the currently chosen TINT
mode to the default settings, and stores them in the TINT
mode again.
To display the PICTURE SETTING menu:
1 Press the
button to display MENU
3
(main menu).
2 Press the ë button to choose PICTURE
SETTING, and press the button.
3 Press the
tings.
button to complete the set-
3
3
The menu disappears.
■ 7,17
■ (&2#02'(
When you set the ECO MODE function to ON, the screen
contrast is automatically adjusted to a setting suitable for the
brightness of your room. This reduces eye strain for you and
the power consumption of the TV.
You can select one of three TINT modes (three kinds of pic-
ture settings) to adjust the picture settings automatically.
1 Press the ë buttons to choose TINT.
2 Press ì buttons to choose a mode.
1 Press ë buttons to choose ECO MODE.
2 Press ì buttons to choose ON.
COOL:
A cool white colour base with a boost in the colour and
contrast levels that creates a more vivid picture.
To cancel the ECO MODE function:
Press ì buttons to choose OFF.
WARM:
A warm orange/red colour base that creates the appro-
priate colour and contrast levels for watching films.
3 Press the
ting.
button to complete the set-
3
NORMAL:
The menu disappears.
A normal white colour base with normal colour and con-
trast levels.
Note:
• If you set the ECO MODE function to ON, the ECO lamp
lights.
3 Press the
ting.
button to complete the set-
3
The menu disappears.
■ 3LFWXUH#$GMXVWPHQW
You can change the picture settings of each TINT mode as
you like.
The picture settings changed are stored in the TINT mode.
1 Press the ë buttons to choose an item.
2 Press the ì buttons to change the set-
ting.
ï
Item
î
Lower
Higher
CONTRAST
(picture contrast)
Darker
Softer
Brighter
Sharper
Deeper
BRIGHT
(picture brightness)
SHARP
(picture sharpness)
Lighter
Reddish
COLOUR
(picture colour)
Greenish
HUE
(picture hue)
4:
Download from Www.Somanuals.com. All Manuals Search And Download.
3,&785(#)($785(6
2 Press the ì buttons to choose the ap-
propriate colour system.
PAL:
PAL system
NTSC 3.58:
NTSC 3.58 MHz system
NTSC 4.43
NTSC 4.43 MHz system
AUTO:
To display the PICTURE FEATURES menu:
This function detects a colour system from the input sig-
nal. Only when you are viewing a picture from Pro-
gramme number PR 0 (AV), or EXT terminal, you can
choose using the AUTO function.
1 Press the
button to display MENU
3
(main menu).
2 Press the ë button to choose PICTURE
FEATURES, and press the button.
3
3 Press the
ting.
button to complete the set-
3
■ $872#915
The AUTO VNR function optimally reduces noise of the TV
automatically according to the noise of the current picture.
The function also adjusts the optimum Sharpness (SHARP).
The menu disappears.
Note:
• The AUTO function may not function properly if you
have poor signal quality. If the picture is abnormal in
the AUTO function, choose another colour system
manually.
1 Press the ë buttons to choose AUTO
VNR.
• When in the Programme numbers PR 0 (AV) to PR
99, you cannot choose NTSC 3.58 or NTSC 4.43.
2 Press the ì buttons to choose AUTO.
MIN:
The AUTO VNR function is cancelled. When you set the
mode to AUTO but feel that the sharpness of the original
picture has not be reproduced fully, change the mode to
MIN. However, a noise remaining in the original picture
may be emphasized.
■ 7=6#$872#$63(&7
You can choose one of three ZOOM modes, REGULAR,
PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the nor-
mal picture (4:3 aspect ratio).
MAX:
This mode always maximizes the noise reduction effect
irrespective of state of the picture. When you set the
mode to AUTO but feel that the noise is remarkable,
change the mode to MAX. However, this may reduce the
sharpness of the picture.
ë
1 Press the
buttons to choose 4:3 AUTO
button.
ASPECT. Then press the
The Sub-menu of the 4:3 AUTO ASPECT function ap-
pears.
3
3 Press the
ting.
button to complete the set-
3
The menu disappears.
■ &2/285#6<67(0
The colour system is chosen automatically. However, if the
picture is not clear or no colour appears, choose the colour
system manually.
ë
2 Press the
mode.
buttons to choose a ZOOM
ë
1 Press the
buttons to choose COLOUR
button.
3 Press the
tings.
button to complete the set-
3
SYSTEM. Then press the
The Sub-menu of the COLOUR SYSTEM function ap-
pears.
3
The menu disappears.
4;
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE FEATURES
■ 3,&785(#7,/7
There are cases where the Earth’s magnetic force may make
the picture tilt. If this happens, you can correct the picture tilt.
ë
1 Press the
buttons to choose PICTURE
button.
TILT. Then press the
The Sub-menu of the PICTURE TILT function appears.
3
ë
2 Press the
comes level.
buttons until the picture be-
3 Press the
ting.
button to complete the set-
3
The menu disappears.
4<
Download from Www.Somanuals.com. All Manuals Search And Download.
6281'#6(77,1*
■ 63($.(5
You can turn off the sound from the TV speakers; but you
should only do this if an audio system is connected to the TV
as a substitute for the TV speakers. When you are using this
function, see “Setting the SPEAKER function” on page 31.
When a sound is not issued from the TV speaker:
If the SPEAKER function is set to OFF, the TV speaker does
not issue sound. Press the ë buttons to choose the
SPEAKER. Then press ì buttons to choose ON.
To display the SOUND SETTING menu:
1 Press the
button to display MENU
3
(main menu).
■ %%(
2 Press the
button to choose SOUND
ë
You can use the BBE function to enjoy easy-to-listen sound
that is faithful to the original sound recorded.
SETTING. Then press the
button.
3
1 Press ë buttons to choose BBE.
2 Press ì buttons to choose ON.
■ 67(5(2#2#,‡,,
When you are viewing a bilingual broadcast programme, you
can choose the sound from Bilingual I (Sub I) or Bilingual II
(Sub II). When the stereo broadcasting is received poorly, you
can change from stereo to mono sound so that you can hear
the broadcast more clearly and easily.
To cancel the BBE function:
Press ì buttons to choose OFF.
3 Press the
ting.
button to complete the set-
3
1
Press
buttons to choose STEREO / I • II.
buttons to choose a sound
ë
ì
The menu disappears.
2 Press
mode.
•
Licensed by BBE Sound, Inc. BBE is a registered trade-
mark of BBE Sound, Inc.
E :Stereo sound
ý
H :mono sound
ýF :Bilingual I (sub I)
■ +<3(5#6281'
You can enjoy sounds with a wider ambience.
ý
ýG :Bilingual II (sub II)
3 Press the
ting.
button to complete the set-
3
1 Press ë buttons to choose HYPER
SOUND.
The menu disappears.
2 Press ì buttons to choose ON.
Note:
To cancel the HYPER SOUND function:
Press the ì buttons to choose OFF.
• The sound mode you can choose differs depending
on the TV programme.
• This function does not work in the EXT modes. And
this function does not appear in the SOUND SET-
TING menu.
3 Press the
ting.
button to complete the set-
3
The menu disappears
Note:
■ 6RXQG#$GMXVWPHQW
You can adjust the sound to your liking.
• The HYPER SOUND function does not work properly
with mono sound.
• The HYPER SOUND lamp lights while the HYPER
1 Press the ë buttons to choose an item.
2 Press the ì buttons to adjust it.
SOUND function is in use.
• You can turn on or off the HYPER SOUND function
with a single press. For details, see “4 HYPER
SOUND Button” on page 12.
ï
Item
BASS
î
Weaker
Weaker
Left
Stronger
Stronger
Right
TREBLE
BALANCE
3 Press the
ting.
button to complete the set-
3
The menu disappears.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
(;7#6(77,1*
3 Press the
ting.
button to complete the set-
3
The menu disappears.
Note:
• The EXT-1 terminal does not support S-VIDEO signal
(Y/C signal) and you cannot set K (S-VIDEO input)
in the EXT-1 terminal.
• Setting K (S-VIDEO input) changes the head
character from “E” to “S”. For example, “E2” is
changed to “S2”.
To display EXT SETTING menu:
•
Even an device which enables the S-VIDEO signal (Y/
C signal) to be output may output a regular video sig-
nal (composite signal) depending on the device set-
ting. If a picture cannot appear because K (S-
VIDEO input) setting has been made, read the device
Instruction Manual carefully again to check for the de-
vice settings.
1 Press the
button to display MENU
3
(main menu).
2 Press the ë button to choose EXT SET-
TING. Then press the button.
3
■ K+609,'(2#LQSXW,
When connecting a device (such as S-VHS VCR) which en-
ables an S-VIDEO signal (Y/C signal) to be output, you can
enjoy high-quality picture of the S-VIDEO signal (Y/C signal).
■ /,67
You can have a name corresponding to the devices connect-
ed for each EXT terminal. Giving a name to an EXT terminal
makes the EXT terminal number appear on the screen, to-
gether with the name.
Preparation:
• At first, read the Device Instruction Manual and “ADDITION-
AL PREPARATION” on page 32 to connect the device to the
TV properly. Second, follow the Device Instruction Manual
to set the device so that a S-VIDEO signal (Y/C signal) can
be output to the TV.
1 Press the ë buttons or ì buttons to
choose an EXT terminal.
• Do not set K(S-VIDEO input) to the EXT terminal con-
nected to a device which cannot output a S-VIDEO (Y/C sig-
nal). If it is set wrongly, a picture cannot appear.
EXT-1
P
1 Press the
buttons or
buttons to
ë
ì
EXT-3
choose an EXT terminal.
EXT-2
EXT-4
P
EXT-1
TV
P
EXT-3
2 Press the blue button to display the name
list (LIST).
EXT-2
EXT-4
P
TV
2 Press the yellow button and set the K
(S-VIDEO input).
A K (S-VIDEO input) mark is displayed. You can view
an S-VIDEO signal (Y/C signal) instead of the regular
video signal (composite signal).
To cancel the K (S-VIDEO input) setting:
Press the yellow button and turn off K (S-VIDEO in-
put) mark.
The regular video signal (composite signal) pictures are
resumed.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
EXT SETTING
3 Press the ë buttons to choose a name.
Then press the
button.
3
The LIST disappears and the name is assigned to the
EXT terminal.
To erase a name assigned to the EXT terminal:
Choose a blank space.
4 Press the
ting.
button to complete the set-
3
The menu disappears.
Note:
• You cannot assign an EXT terminal name not found
in the name list (LIST).
■ '8%%,1*
You can choose a signal source to be output from an EXT-2
terminal.
You can choose any one of the output signal of the device
connected to the EXT terminal and the picture and sound
from a TV channel you are currently viewing to output it to the
EXT-2 terminal.
1 Press the ì buttons to choose the EXT-2
terminal.
2 Press the ë buttons to choose an EXT
terminal or TV.
The arrow in the menu represents a signal flow. The left
side of the arrow denotes a signal source output from the
EXT-2 terminal.
EXT-1/EXT-3/EXT-4:
The output signal of the device connected to an EXT ter-
minal passes through the TV and is output from the EXT-
2 terminal.
TV:
The picture and sound of the TV channel you are cur-
rently viewing are output from the EXT-2 terminal.
3 Press the
ting.
button to complete the set-
3
The menu disappears.
Note:
• During dubbing, you cannot turn off the TV. Turning
off the TV also turns off the output from the EXT-2 ter-
minal.
• When you choose an EXT terminal as an output, you
can view a TV programme or a picture from the other
EXT terminal while dubbing the picture from a de-
vice connected to the EXT terminal onto a VCR con-
nected to the EXT-2 terminal.
• The RGB signals from the TV games cannot be out-
put.Teletext programmes cannot be output.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
)($785(6
■ %/8(#%$&.
You can set the TV to automatically change to a blue screen
and mute the sound if the signal is weak or absent, or when
there is no input from an external device.
1 Press the
BACK.
buttons to choose BLUE
ë
2 Press theì buttons to choose ON.
To display the FEATURES menu:
1 Press the
button to display MENU
To cancel the BLUE BACK function:
Press theì buttons to choose OFF.
3
(main menu).
2 Press theë button to choose FEATURES.
3 Press the
ting.
button to complete the set-
3
Then press the
button.
3
The menu disappears.
■ 6/((3#7,0(5
You can set the TV to automatically turn off after a specified
period of time.
■ &+,/'#/2&.
When there is a TV channel you wish your children not to
watch, you can use the CHILD LOCK function to lock out the
TV channel. Even when a child chooses a Programme num-
ber (PR) in which a locked TV channel has been registered,
1 Press the
buttons to choose SLEEP
ë
TIMER. Then press the
A Sub-menu of the SLEEP TIMER function appears.
button.
3
the screen will change to blue and displays (CHILD LOCK)
@
so the TV channel cannot be viewed. Unless you enter a pre-
set ID number by a special operation, the lock cannot be re-
leased and the child cannot view the TV channel programs.
7R#VHW#WKH#&+,/'#/2&.#IXQFWLRQ
1 Press the ë buttons to choose CHILD
LOCK. Then press theA button.
“SET ID NO.” (ID number setting screen) appears.
2 Press the
time.
buttons to set the period of
ì
You can set the period of time a maximum of 120 min-
utes (2 hours) in 10 minute increments.
To cancel the SLEEP TIMER function:
Press the ï button to set a period of time to “OFF.”
2 Set the ID number to your liking.
3 Press the
tings.
button to complete the set-
3
1 Press theë buttons to choose a number.
2 Press theì buttons to move the cursor.
The menu disappears.
Note:
3 Press the
button.
3
• The SLEEP TIMER lamp lights while the SLEEP TIM-
ER function is operating.
The Sub-menu of CHILD LOCK appears.
• One minute before the SLEEP TIMER function turns
off the TV, “GOOD NIGHT!” appears.
• The SLEEP TIMER function cannot be used to turn
off the TV’s main power.
• When the SLEEP TIMER function is on, you can dis-
play the Sub-menu of the SLEEP TIMER function
again to confirm and/or change the remaining peri-
od of time of the SLEEP TIMER function. Press the
button to exit the menu after confirming and / or
changing the remaining time.
3
4 Press theë buttons to choose a TV
channel.
Every time you press the ë buttons, the Programme
number (PR) changes, and the picture of the TV channel
registered in the Programme number (PR) is displayed
on the screen.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
5 Press the blue button and set the CHILD
LOCK function.
■ '(&2'(5#+(;705,
Only when connecting a Decoder with a T-V LINK compatible
VCR connected to the EXT-2 terminal, you can use this func-
tion. To operate this function, see “Using the DECODER
(EXT-2) function” on page 30.
(CHILD LOCK) appears and the TV channel is locked.
@
To reset the CHILD LOCK function:
Press the blue button again.
(CHILD LOCK) disappears.
Caution:
@
• If you have not connected a Decoder with a T-V LINK com-
patible VCR connected to the EXT-2 terminal, setting this
function to “ON” by mistake causes the picture/sound of a
TV channel you are currently viewing not to be issued.
6 Press the
ting.
button to complete the set-
3
The menu disappears.
Note:
• To disable easy resetting of the CHILD LOCK func-
tion, the menu disappears by choosing the CHILD
LOCK function and pressing the
ordinary menu operation.
button as in the
3
7R#YLHZ#D#ORFNHG#79#FKDQQHO
1 Choose a Programme number (PR) in
which a TV channel locked with the
Number buttons or PR LIST.
The screen changes to blue and the (CHILD LOCK)
@
appears. You cannot view the TV channel.
2 Press the
(Information) button to
9
display “ID NO.” (ID No. input screen).
3 Press the Number buttons to enter the ID
number.
The lock is temporarily released so you can view the TV
channel.
If you have forgotten the ID number:
Perform step 1 of “To set the CHILD LOCK function”. Af-
ter confirming the ID number, press the
the menu.
button to exit
4
Note:
• Even if you reset the lock temporarily, it does not
mean that the CHILD LOCK function set for the TV
channel is cancelled. The next time anyone at-
tempts to view the TV channel, it will be locked
again.
• When you would like to cancel the CHILD LOCK
function, you must perform the operation “To set the
CHILD LOCK function” again.
• To disable easy choosing of a Programme number
(PR) in which a locked TV channel has been regis-
tered, the Programme number (PR) has been set
that it cannot be chosen by the
operation buttons at the TV.
buttons or the
ë
• To disable easy resetting of the lock, “ID NO.” (ID
No. input screen) is set so that it cannot appear un-
less you press the
(Information) button.
9
57
Download from Www.Somanuals.com. All Manuals Search And Download.
,167$//
To cancel the AUTO PROGRAM function:
Press the button.
4
3 After the TV channels have been regis-
tered in the Programme numbers (PR), the
EDIT menu appears.
You can proceed to edit the Programme numbers (PR)
using the EDIT/MANUAL function. For details, see “ED-
IT/MANUAL” on page 26.
To display the INSTALL menu:
When not using the EDIT/MANUAL function:
If you do not need to use the EDIT/MANUAL function, go
to the next step.
1 Press the
button to display MENU
3
(main menu).
2 Press the
button to choosetheINSTALL
ë
4 Press the
menu.
button to display the T-V LINK
3
menu. Then press the
button.
3
■ /$1*8$*(
You can choose the language you want to use for the on-
screen display from the language list in a menu.
1 Press the
buttons to choose LAN-
ë
GUAGE. Then press the
A sub-menu of the LANGUAGE function appears.
button.
3
5 Operate the T-V LINK menu according to
the type of VCR connected to the EXT-2
terminal.
When a T-V LINK compatible VCR is not con-
nected:
Press the
button to exit the T-V LINK menu.
4
The T-V LINK menu disappears, and all the settings are
completed.
When a T-V LINK compatible VCR is connected:
Follow the operating procedure “Downloading the data
to VCR” on page 30 to transmit the Programme number
(PR) data to the VCR.
2 Press the
guage.
buttons to choose a lan-
ë
Note:
3 Press the
ting.
button to complete the set-
3
• When your TV can detect the TV channel name from
the TV channel broadcast signal, it automatically
registers the TV channel name (ID) to the Pro-
gramme number (PR) in which the TV channel has
been registered.
The menu disappears.
• If a TV channel you want to view is not set to a Pro-
gramme number (PR), manually set it using the
MANUAL function. For details, see “EDIT/MANUAL”
on page 26.
■ $872#352*5$0
You can automatically register the TV channels which can be
received well at your residence in the TV’s Programme num-
bers (PR) by performing the following.
• The TV channel is not registered in Programme
number PR 0 (AV). When you want to register a TV
channel to PR 0 (AV) manually set it using the MAN-
UAL function. For details, see “EDIT/MANUAL” on
page 26.
1 Press the
buttons to choose AUTO
ë
PROGRAM.
2 Press the
button to start the AUTO
3
PROGRAM function.
The AUTO PROGRAM menu appears and received TV
channels are automatically registered in the Programme
numbers (PR).
58
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL
2 Follow the operation description of a func-
tion you want to use and operate the func-
tion.
■ (',720$18$/
The EDIT/MANUAL functions are divided into two types: ed-
iting of the current Programme numbers (PR) (EDIT func-
tions) and manual registration of a TV channel you want to
view to the Programme number (PR) (MANUAL function).
The details about these functions are as follows:
3 Press the
tings.
button to complete the set-
3
The T-V LINK menu appears.
MOVE:
This function changes a Programme number (PR) of a TV
channel.
ID:
This function registers a Channel name (ID) to a TV channel.
INSERT:
This function adds a new TV channel in the current Pro-
gramme numbers (PR) list by using the CH/CC number.
4 Operate the T-V LINK menu according to
the type of VCR connected to the EXT-2
terminal.
DELETE:
This function deletes a unnecessary TV channel.
When a T-V LINK compatible VCR is not con-
nected:
MANUAL:
This function manually registers a new TV channel in a Pro-
gramme number (PR).
Press the
button to exit the T-V LINK menu.
4
The T-V LINK menu disappears and all the settings are
completed.
Caution:
When a T-V LINK compatible VCR is connected:
• Using the MOVE, DELETE or INSERT function rewrites the
current Programme numbers (PR) list. Resultingly, the Pro-
gramme number (PR) of some of the TV channels will
change.
Follow the operating procedure “Downloading the data
to VCR” on page 30 to transmit the Programme number
(PR) data to the VCR.
• Using the MANUAL function for a TV channel for which the
CHILD LOCK function has been set cancels the CHILD
LOCK function for the TV channel.
029(
1 Press the
channel.
ë
buttons to choose a TV
• Using the MANUAL function for a TV channel for which the
DECODER (EXT-2) function has been set to ON returns the
setting of the DECODER (EXT-2) function for the TV chan-
nel to OFF.
ë
Every time you press the
buttons, the Programme
number (PR) is changed over, and the picture of the TV
channel registered in the Programme number (PR) ap-
pears on the screen.
• When a TV channel has already been registered in PR 99,
using the INSERT function deletes the TV channel.
î
2 Press the button to start the MOVE func-
Note:
tion.
• For Programme number PR 0, “AV” appears in the Pro-
gramme numbers (PR) list.
• An EXT terminal number does not appear in the Pro-
gramme numbers (PR) list.
• The CH/CC number is a number unique to the TV and
corresponding to the Channel number of a TV channel.
For the relationship of a Channel number and a CH/CC
number, see “CH/CC NUMBER” on page 28.
• You cannot use the INSERT function if you do not know a
Channel number of a TV channel. Use the MANUAL func-
tion to register a TV channel in the Programme number
(PR).
ë
3 Press the
buttons to choose a new
Programme number (PR).
ë
1 Press the
buttons to choose EDIT/
button.
MANUAL. Then press the
3
To cancel the MOVE function:
Press the (Information) button.
9
59
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL
ï
4 Press the button to change the Pro-
Note:
gramme number (PR) of a TV channel to a
new Programme number (PR).
• You can register your unique Channel name (ID) to
the TV channel. When step 3 is completed, do not
ì
go to step 4, but press the
buttons to move the
buttons to choose a character for
completing the Channel name (ID). Then press the
button to register the Channel name (ID) to the TV
,'
ë
cursor and the
ë
1 Press the
channel.
buttons to choose a TV
3
channel.
ë
Every time you press the
buttons, the Programme
number (PR) is changed over, and the picture of the TV
channel registered in the Programme number (PR) ap-
pears on the screen.
,16(57
Preparation:
• A CH/CC number unique to this TV and corresponding to
the Channel number of a TV channel is required. Find the
corresponding CH/CC number from a table “CH/CC
NUMBER” on page 28 based on the Channel number of the
TV channel.
2 Press the red button to start the ID func-
tion.
ë
1 Press the
buttons to choose a Pro-
gramme number (PR) for which you will
register a new TV channel.
2 Press the green button and start the IN-
SERT function.
ë
3 Press the
buttons to choose the first
character of a Channel name (ID) you want
to attach to the TV channel.
To cancel the INSERT function:
Press the
(Information) button.
9
ë
3 Press the
buttons to choose “CC” or
“CH” according to the CH/CC number of
the TV channel.
4 Press the blue button to display the ID LIST
(channel name list).
To cancel the INSERT function:
Press the
(Information) button.
9
4 Press the Number button to enter the re-
maining CH/CC number.
The TV shifts to registration mode.
When the registration is completed, the picture of the TV
channel appears on the screen.
Note:
• The CH/CC number is a number indicating the
broadcast frequency to the TV. If the TV cannot de-
tect the TV channel corresponding to the broadcast
frequency indicated by the CH/CC number, a pic-
ture in the no-signal state appears.
ë
5 Press the
nel name (ID).
buttons to choose the Chan-
To cancel the ID function:
Press the
(Information) button.
9
6 Press the
button to register a Channel
3
name (ID) to a TV channel.
5:
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL
'(/(7(
■ &+2&´%(5
1 Press the ë buttons to choose a TV
• When you want to use the INSERT function on page 27,
find the CH/CC number corresponding to the Channel
number of the TV channel from this table.
channel.
Every time you press the ë buttons, the Programme
number (PR) is changed over, and the picture of the TV
channel registered in the Programme number (PR) ap-
pears on the screen.
CH
Channel
CH
Channel
E40
E41
E42
E43
E44
E45
E46
E47
E48
E49
E50
E51
E52
E53
E54
E55
E56
E57
E58
E59
E60
E61
E62
E63
E64
E65
E66
E67
E68
E69
CH 02 / CH 202
CH 03 / CH 203
CH 04 / CH 204
CH 05 / CH 205
CH 06 / CH 206
CH 07 / CH 207
CH 08 / CH 208
CH 09 / CH 209
CH 10 / CH 210
CH 11 / CH 211
CH 12 / CH 212
CH 21 / CH 221
CH 22 / CH 222
CH 23 / CH 223
CH 24 / CH 224
CH 25 / CH 225
CH 26 / CH 226
CH 27 / CH 227
CH 28 / CH 228
CH 29 / CH 229
CH 30 / CH 230
CH 31 / CH 231
CH 32 / CH 232
CH 33 / CH 233
CH 34 / CH 234
CH 35 / CH 235
CH 36 / CH 236
CH 37 / CH 237
CH 38 / CH 238
CH 39 / CH 239
E2, IR A
CH 40 / CH 240
CH 41 / CH 241
CH 42 / CH 242
CH 43 / CH 243
CH 44 / CH 244
CH 45 / CH 245
CH 46 / CH 246
CH 47 / CH 247
CH 48 / CH 248
CH 49 / CH 249
CH 50 / CH 250
CH 51 / CH 251
CH 52 / CH 252
CH 53 / CH 253
CH 54 / CH 254
CH 55 / CH 255
CH 56 / CH 256
CH 57 / CH 257
CH 58 / CH 258
CH 59 / CH 259
CH 60 / CH 260
CH 61 / CH 261
CH 62 / CH 262
CH 63 / CH 263
CH 64 / CH 264
CH 65 / CH 265
CH 66 / CH 266
CH 67 / CH 267
CH 68 / CH 268
CH 69 / CH 269
E3, IR B, ITALY A
E4, IR C, ITALY B
E5, IR D, ITALY D
2 Press the yellow button to delete the TV
channel.
E6, IR E, ITALY E
E7, IR F, ITALY F
E8, IR G
The TV channel is deleted from the Programme num-
bers (PR) list.
E9, ITALY G
E10, IR H, ITALY H
E11, IR J, ITALY H+1
E12, ITALY H+2
E21
E22
E23
E24
E25
E26
E27
E28
E29
E30
E31
0$18$/
1 Press the
E32
E33
ë
buttons to choose a Pro-
E34
E35
gramme number (PR) to which you want to
register a new TV channel.
E36
E37
E38
E39
2 Press the blue button to activate the MAN-
UAL function.
CC
Channel
S1
CC
Channel
S31
CC 01 / CC 201
CC 02 / CC 202
CC 03 / CC 203
CC 04 / CC 204
CC 05 / CC 205
CC 06 / CC 206
CC 07 / CC 207
CC 08 / CC 208
CC 09 / CC 209
CC 10 / CC 210
CC 11 / CC 211
CC 12 / CC 212
CC 13 / CC 213
CC 14 / CC 214
CC 15 / CC 215
CC 16 / CC 216
CC 17 / CC 217
CC 18 / CC 218
CC 19 / CC 219
CC 20 / CC 220
CC 21 / CC 221
CC 22 / CC 222
CC 23 / CC 223
CC 24 / CC 224
CC 25 / CC 225
CC 26 / CC 226
CC 27 / CC 227
CC 28 / CC 228
CC 29 / CC 229
CC 30 / CC 230
CC 31 / CC 231
CC 32 / CC 232
CC 33 / CC 233
CC 34 / CC 234
CC 35 / CC 235
CC 36 / CC 236
CC 37 / CC 237
CC 38 / CC 238
CC 39 / CC 239
CC 40 / CC 240
CC 41 / CC 241
CC 75 / CC 275
CC 76 / CC 276
CC 77 / CC 277
CC 78 / CC 278
CC 79 / CC 279
S2
S32
S3
S33
S4
S34
S5
S35
S6
S36
S7
S37
S8
S38
S9
S39
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
S24
S25
S26
S27
S28
S29
S30
S40
S41
X
Y
To cancel the MANUAL function:
Z, ITALY C
Z+1
Press the
(Information) button.
9
Z+2
3 Press the green or red button to search for
a TV channel.
Scanning stops when the TV finds a TV channel. Then
the TV channel is displayed.
4 Press the green or red button repeatedly
until the TV channel you want appears.
If the TV channel reception is poor:
Press the blue or yellow button to fine-tune the TV chan-
nel.
5 Press the
button and register the TV
3
channel to a Programme number (PR).
The normal EDIT menu is resumed.
5;
Download from Www.Somanuals.com. All Manuals Search And Download.
'(02
To display the DEMO menu:
1 Press the
button to display MENU
3
(main menu).
2 Press theë button to choose DEMO. Then
press the button.
3
The DEMO function automatically demonstrates some of the
TV functions.
1 Press the ë buttons to choose ON.
2 Press the
tings.
button to complete the set-
3
The DEMO function is set to ON, and the demonstration
will start.
To stop the demonstration:
Press one of the buttons on the remote
control.
When the DEMO function is set to ON:
Each time the TV is turned on, the demonstration starts
automatically. If you do not want that to happen, perform
the following operations to cancel the DEMO function:
1 Display the DEMO menu again.
2 Press the ë buttons to choose OFF.
3 Press the
function.
button to cancel the DEMO
3
5<
Download from Www.Somanuals.com. All Manuals Search And Download.
$'',7,21$/#0(18#23(5$7,216
4 Press the
buttons to choose FEA-
ë
■ 'RZQORDGLQJ#WKH#GDWD#WR#9&5
You can transmit to the latest Programme numbers (PR) data
to the VCR with the T-V LINK function.
TURES. Then press the
button.
3
The FEATURES menu appears.
Caution:
• Only when the T-V LINK compatible VCR is connected to
the EXT-2 terminal, this operation is enabled.
• Only when the T-V LINK menu is being displayed, this oper-
ation is enabled.
5 Press the
buttons to choose DECOD-
ë
ER (EXT-2) . Then press the
choose ON.
buttons to
ì
An unscrambled picture appears.
To cancel the DECODER (EXT-2) function:
Press the buttons to choose OFF.
ì
1 Turn on the VCR.
6 Press the
ting.
button to complete the set-
3
2 Press the
button.
3
The data transmission begins.
The T-V LINK menu appears.
The T-V LINK menu disappears once the data transmis-
sion ends.
When the T-V LINK menu is changed over to
another menu:
The menu operation at the TV side is completed and it is
shifted to the menu operation at the VCR side. Refer to
the VCR Instruction Manual and operate the VCR.
7 Follow the operating procedure “Down-
loading the data to VCR” on page 30 to
transmit the Programme number (PR) data
to the VCR.
Note:
• If “FEATURE NOT AVAILABLE” appears at the T-V
LINK menu, ensure the following three items are cor-
rect; then press the
sion.
button to retry data transmis-
3
8 If you have another TV channel capable of
being unscrambled with a Decoder, repeat
steps 2 through 7.
− Has the T-V LINK compatible VCR been connect-
ed to the EXT-2 terminal?
− Has the VCR power been turned on?
Note:
− Does the SCART cable that is connected to the
EXT-2 terminal to T-V LINK compatible VCR have
all proper connections?
• If for some reason the DECODER (EXT-2) function
has been set to “ON” but the TV channel cannot be
unscrambled, check the following:
− Has the Decoder been connected to the VCR
properly according to the VCR and Decoder In-
struction Manuals?
■ 8VLQJ#WKH#'(&2'(5#+(;705,##
− Has the Decoder power been turned on?
IXQFWLRQ
−
Can the TV channel be unscrambled with a De-
coder?
When connecting a Decoder with a T-V LINK compatible VCR
connected to the EXT-2 terminal, use the DECODER (EXT-2)
function to unscramble the scrambled TV channels.
− Is it necessary to change the VCR settings in or-
der to connect the Decoder? Confirm that the
VCR is set properly by rechecking the VCR In-
struction Manual.
1 Turn on the Decoder power.
2 Display the TV channel capable of being
unscrambled with the Decoder on the TV.
Even if the Decoder is functioning, a scrambled picture
appears at this time.
3 Press the
button to display the MENU.
3
The MENU (main menu) appears.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL MENU OPERATIONS
■ 6HWWLQJ#WKH#63($.(5#IXQFWLRQ
Turn off the SPEAKER function so that TV speakers will not
issue any sound.
1. Press the
button to display the MENU
3
(main menu).
2. Press the
buttons to choose SOUND
ë
SETTING. Then press the
play the SOUND SETTING menu.
button to dis-
3
The SOUND SETTING menu appears.
3. Press the
buttons to choose SPEAK-
ë
ER. Then press the
OFF.
buttons to choose
ì
The sound from the TV speakers are cut.
4. Press the
tings.
button to complete the set-
3
The menu disappears.
Note:
• The ì buttons of the TV remote control and the D
(volume) buttons at the front panel of your TV set can be
used to control the volume of each speaker simultane-
ously.
• Setting the volume of the amplifier too high may damage
the front speakers.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
$'',7,21$/#35(3$5$7,21
■ &RQQHFWLQJ#WKH#H[WHUQDO#GHYLFHV
Connect the devices to the TV, paying attention to the Rear
panel connections and the Front panel connections.
Before connecting anything:
• Read the manuals provided with the devices. Depending
on the devices, the connection method may differ from
the figure. In addition, the device settings may be
changed depending on the connection method to secure
proper operation.
• Turn off all the devices including the TV.
(Behind the door)
• The “SPECIFICATIONS” on the back cover contains the
details of the EXT terminals. If you are connecting a de-
vice not listed in the following connection diagram, see
the table to choose the best EXT terminal.
• Note that connecting cables are not supplied.
1 VCR (composite signal)
2 VCR (composite signal/S-VIDEO signal)
3 T-V LINK compatible VCR (composite signal/S-VIDEO sig-
nal)
4 Decoder
5 DVD player (composite signal/S-VIDEO signal)
6 DVD player (composite signal/RGB signal)
7 TV game (composite signal/RGB signal)
8 TV game (composite signal/S-VIDEO signal)
9 Headphones
0 Camcorder (composite signal/S-VIDEO signal)
- SCART cable
= Audio cable
~ Video cable
! S-VIDEO cable
EXT-2
EXT-3
S
S
L
R
EXT-1
AUDIO OUT
65
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL PREPARATION
'HYLFHV#ZKLFK#FDQ#RXWSXW#WKH#
609,'(2#VLJQDO#+<2&#VLJQDO,#VXFK#DV
D#609+6#9&5
■ &RQQHFWLQJ#6SHDNHUV2$PSOL0
ILHU
While referring to the Audio equipment connection diagram,
connect the audio equipment you desire to the TV.
You can use external front speakers to listen to the TV sound
instead of the TV speakers. For details of how to operate
them, see “Setting the SPEAKER function” on page 31.
Connect the device to an EXT terminal other than the EXT-1
terminal.
You can choose a video input signal from the S-VIDEO signal
(Y/C signal) and regular video signal (composite signal). For
details of how to operate the device, see “K(S-VIDEO in-
put)” on page 21.
Before connecting anything:
• Read the manuals provided with the amplifier and speak-
ers.
709#/,1.#FRPSDWLEOH#9&5
• Turn the TV and Amplifier off.
Be sure to connect the T-V LINK compatible VCR to the EXT-
2 terminal. If not, the T-V LINK function will not work properly.
• To prevent magnetism from the speakers adversely ef-
fecting the TV screen, use magnetic-shielded speakers
for the front speakers.
Note:
• When connecting a T-V LINK compatible VCR to the EXT-
2 terminal, be sure to connect the Decoder to the VCR. If
not, the T-V LINK function may not work properly. After
you have registered TV channels to the Programme num-
bers (PR), set the DECODER (EXT-2) function for the Pro-
gramme number (PR) to ON in order to unscramble a
scrambled TV channel. For details of operation, see “Us-
ing the DECODER (EXT-2) function” on page 30.
• Note that connecting cables are not supplied.
2
1
L
R
AUDIO OUT
(Terminals on rear)
&RQQHFWLQJ#KHDGSKRQHV
Connect the headphones with a stereo mini-jack (of 3.5mm in
diameter) to the headphone jack at the TV front panel.
1 Amplifier
2 Front speakers (Magnetic-shielded type)
Note:
Note:
• When you connect the headphones, the TV speakers is-
sue no sound.
• The output from the AUDIO OUT terminal is not interrupt-
ed by headphone connection to the TV. You cannot cut
the sound from the front speaker even if you connect a
headphone to the TV.
9LGHR2VRXQG#VLJQDO#RXWSXW#IURP#WKH
(;705#WHUPLQDO
You can arbitrarily change over the output of the video/sound
signal from the EXT-2 terminal. It is useful when you want to
dub the video/sound from another device on the VCR con-
nected to the EXT-2 terminal. For details on how to do this op-
eration, see “DUBBING” on page 22.
79#RXWSXW#IURP#WKH#(;704#WHUPLQDO
The output of video/sound signal of a TV channel you are cur-
rently viewing is always output from the EXT-1 terminal.
Note:
• Changing over a Programme number (PR) also changes
over the TV output from the EXT-1 terminal.
• The video/sound signal from an EXT terminal cannot be
output.
• Teletext programmes cannot be output.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
79#%877216#$1'#3$576
■ )URQW#3DQHO
l
Push to open
(Behind the cover)
2
3
4
1
-
5
8
9
0
6
7
1 EXT-4 terminal
pages 21 and 32
pages 32
7 HYPER SOUND lamp
8 ECO lamp
pages 12 and 20
page 17
2 Headphone jack (mini jack)
3 D (Volume) button
4 P ∨/∧ buttons / –/+ buttons
5 Remote control sensor
6 ECO sensor
page 10
9 SLEEP TIMER lamp
0 Power lamp
page 23
page 10
pages 5 and 8
pages 5 and 8
- Main power button
Caution:
• Do not grasp the TV by the front panel cover when moving the TV set. If you do, you may break the cover.
■ 5HDU#3DQHO
EXT-2
EXT-3
S
S
L
R
EXT-1
AUDIO OUT
= AUDIO OUT terminal
~ Aerial socket
page 33
page 4
@ EXT-2 terminal
# EXT-3 terminal
pages 4, 7, 21 and 32
pages 21 and 32
! EXT-1 terminal
pages 4, 21 and 32
67
Download from Www.Somanuals.com. All Manuals Search And Download.
7528%/(6+227,1*
If a problem arises while you are using the TV, please read this “Troubleshooting” well before you request having the TV repaired.
You may be able to fix it easily by yourself. For example, if the AC plug is disconnected from the AC outlet, or the TV aerial has
problems, you may think there is a problem with the TV itself.
Important:
• This Troubleshooting guide only covers problems whose cause are not easy to determine. If a question arise when you are
operating a function, read the page(s) corresponding to the operation of the function well, not this Troubleshooting guide.
• After you have followed the Troubleshooting description or the operating description of the functions concerned without any suc-
cess, remove the AC plug from the AC outlet and request a repair of your TV. Do not attempt to repair the TV by yourself or
remove the rear cover of the TV.
• When the TV channel reception is poor, it can be hard to
,I#\RX#FDQQRW#WXUQ#RQ#WKH#79
hear the stereo or bilingual sound. In this case, follow the
• Is the AC plug connected to the AC outlet?
description “STEREO / I•II” on page 20 to hear the sound
more easily by changing it to a mono sound.
• Is the Power lamp lit? If not, press the Main power button.
2SHUDWLRQ#GLVDEOHG
1R#SLFWXUH21R#VRXQG
• Have the batteries of the remote control become exhaust-
ed? Follow the description “Putting Batteries into the Re-
mote Control” on page 4 and replace them with new
batteries to try to solve the problem.
• Have you chosen a TV channel whose reception is extreme-
ly bad? In this case, the BLUE BACK function will be activat-
ed, the entire screen becomes blue, and the sound is muted.
In spite of this, if you want to view the TV channel, follow the
description “BLUE BACK” on page 23 to try to change the
BLUE BACK function setting to OFF.
• Have you attempted to use the remote control at the sides
or rear of the TV or at a location more than seven meters
apart from the TV location? Operate the remote control in
the front of your TV or a location less than seven meters
from your TV to try to solve the problem.
• Have you connected the headphones to the TV? Connect-
ing the headphones to the TV causes sounds not to be is-
sued from the TV speakers.
• When you are viewing a teletext programme, you cannot op-
• Have you set the SPEAKER function to OFF? Follow the de-
scription “SPEAKER” on page 20 to confirm the SPEAKER
function setting to try to solve the problem.
erate the menus. Press the
button to return the teletext
4
programme to the ordinary TV programme to try operating
the menus.
3RRU#SLFWXUH
• If noise totally obscures the picture (snow), the aerial or aer-
ial cable may have trouble. Check the following to try to
solve the trouble:
• If the TV operation becomes disabled suddenly, press the
Main power button on the TV and turn off the main power.
Try to press the Main power button again to turn on the main
power. If the TV returns to a normal state, it is not a failure.
Has the TV and aerial been connected properly?
Has the aerial cable been damaged?
Is the aerial pointed to the right direction?
Is the aerial itself faulty?
2WKHU#FRQFHUQV
• When the SLEEP TIMER function operates, the TV is auto-
matically turned off. If the TV is turned off suddenly, try to
press the
(Standby) button to turn on the TV once
=
again. At this time, if the TV resumes a normal state, there
• If the TV or aerial receives interference from the other devic-
es, stripes or noise may appear in the picture. Move such
devices as an amplifier, personal computer, or a hair drier
that can cause interference away from your TV, or try
changing its location. If the aerial suffers interference from a
radio tower or high-voltage wire, please contact your local
dealer.
is no problem.
• When the TV is receiving a wide-screen signal (WSS) or a
signal concerning the screen size from an external device,
the ZOOM mode automatically changes. When you want to
resume the previous ZOOM mode, press the ZOOM button
again.
• If the TV receives interference from signal reflecting from
mountains or building, double-pictures (ghosting) will occur.
Try to change the aerial’s direction or replace the antenna
with the one with better directionality.
• If you bring a magnetised device such as a speaker near to
your TV, a picture may be warped or unnatural colors ap-
pear at he corners of the screen. In this case, keep the de-
vice apart from your TV. If the speakers causes such
phenomena, use the magnetic-shielded speakers instead.
• Are your COLOUR SYSTEM settings correct? Follow the
description “COLOUR SYSTEM” on page 18 to try to solve
the trouble.
• A picture may be tited due to the influence of the earth’s
magnetism. In this case, use the “PICTURE TILT” on
page 19 to complete the tilt.
• Has COLOUR or BRIGHT been controlled properly? Follow
the description “Picture Adjustment” on page 17 to try to ad-
just them properly.
• The TV may emit a crackling sound due to a sudden change
in temperature. It does not matter if a picture or sound does
not show any abnormality. If you hear crackling sounds fre-
quently while you are viewing the TV, other causes may be
assumed. For precautionary purposes, request your service
technician to inspect it.
• Videotaping teletext is not recommended because it may
not record correctly.
• When a white and bright still image (such as a white dress)
is displayed on the screen, the white part may look as if it
were coloured. It is a phenomenon unavoidable due to the
nature of the picture tube itself, and not due to a TV failure.
When the picture disappears from the screen, the unnatural
colours will also disappear.
• Touching the screen may cause you feel a slight electric
shock due to its static electricity. It is an unavoidable phe-
nomenon due to the construction of the picture tube. It is not
a problem with the TV. You can rest assured that this static
discharge does not have harmful influence over the human
body.
3RRU#VRXQG
• Have you adjusted BASS or TREBLE properly? If not, follow
the description “Sound Adjustment” on page 20 to try to ad-
just them properly.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
63(&,),&$7,216
Model
AV-28WFT1EI*
Item
Broadcasting systems
Colour systems
CCIR I
PAL
•
The EXT terminals also support the NTSC 3.58/4.43 MHz system.
Channels and frequencies
Sound-multiplex systems
Teletext systems
Power requirements
Power consumption
Picture tube size
Audio output
IR A-J, E2-E12, E21-E69, S1-S41, X, Y, Z, Z+1, Z+2, ITALY A-H, ITALY H+1, ITALY H+2
NICAM (I) system
FLOF (Fastext), WST (World Standard Text)
220 - 240 V AC, 50 Hz
Maximum: 168 W, Average: 115 W, Standby: 0.8 W
Viewable area 66 cm (measured diagonally)
Rated Power output: 7.5 W + 7.5 W
Speakers
(16cm × 4cm) oval × 2
EXT-1 terminal
Euroconnector (21-pin, SCART)
•
•
Video input, Audio L/R inputs and RGB inputs are available.
TV broadcast outputs (Video and Audio L/R) are available.
EXT-2 terminal
Euroconnector (21-pin, SCART)
•
•
•
Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
Video and Audio L/R outputs are available.
T-V LINK functions are available.
EXT-3 terminal
EXT-4 terminal
Euroconnector (21-pin, SCART)
Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
•
RCA connectors × 3
S-VIDEO connector × 1
•
Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
AUDIO OUT terminal
RCA connectors × 2
•
•
Variable audio L/R outputs are available.
Variable out 0-1 Vrms, low impedance
Headphone jack
Dimensions (W × H × D)
Weight
Stereo mini-jack (3.5 mm in diameter)
780 mm × 509 mm × 499 mm
39 kg
Accessories
Remote control unit RM-C51 × 1
AAA/R03 dry cell battery × 2
* A basic model number. The actual model number may have characters added (such as “S” denoting silver) indicating
the colour of the TV set.
Design and specifications subject to change without notice.
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or demonstration pur-
pose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of the original picture sources, as this
constitutes an infringement of copyright.
LCT0622-001A-U
0300-T-CR-JMUK
©2000 VICTOR COMPANY OF JAPAN, LIMITED
Download from Www.Somanuals.com. All Manuals Search And Download.
|