CD RECEIVER
CD-RECEIVER
RECEPTEUR CD
CD-RECEIVER
KD-G302/KD-G301
KD-G302
KD-G301
• This unit is equipped with the display demonstration. To cancel it, see page 6.
• Dieses Gerät ist mit einer Demonstrationsfunktion für das Display ausgestattet. Auf Seite 6 wird
beschrieben, wie Sie diese Demonstrationsfunktion deaktivieren können.
• Cet appareil est équipé d’une fonction de démonstration des affichages. Pour l’annuler, référez-vous
à la page 6.
• Dit toestel heeft een display-demonstratiefunctie. Zie bladzijde 6 voor het annuleren van deze
functie.
For installation and connections, refer to the separate manual.
Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch.
Pour l’installation et les raccordements, se référer au manuel séparé.
Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de
desbetreffende handleidingI. NSTRUCTIONS
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
GEBRUIKSAANWIJZING
GET0187-001A
[E/EX]
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
CONTENTS
How to reset your unit ...............................
How to use the MODE button ...................
2
2
OTHER MAIN FUNCTIONS ................ 23
Changing the general settings (PSM) ....... 23
Detaching the control panel ...................... 26
LOCATION OF THE BUTTONS ............
4
4
Control panel.............................................
CD CHANGER OPERATIONS .............. 27
About MP3 discs ....................................... 27
Playing discs ............................................. 28
Selecting the playback modes .................. 30
BASIC OPERATIONS .......................
Turning on the power ................................
Canceling the display demonstration ........
Setting the clock........................................
5
5
6
7
EXTERNAL COMPONENT OPERATIONS ... 31
Playing an external component................. 31
RADIO OPERATIONS ......................
Listening to the radio.................................
Storing stations in memory .......................
8
8
9
DAB TUNER OPERATIONS ................ 32
Tuning in to an ensemble and one of the
Tuning in to a preset station ...................... 10
services .................................................. 32
Storing DAB services in memory .............. 33
Tuning in to a preset DAB service ............. 34
What you can do more with DAB .............. 35
RDS OPERATIONS ......................... 11
What you can do with RDS ....................... 11
Other convenient RDS functions and
adjustments ............................................ 16
USING THE REMOTE CONTROLLER ..... 36
Location of the buttons.............................. 37
CD OPERATIONS ........................... 18
Playing a CD ............................................. 18
Locating a track or a particular portion
TROUBLESHOOTING ...................... 38
MAINTENANCE ............................. 40
on a CD .................................................. 19
Selecting CD playback modes .................. 20
Prohibiting CD ejection ............................. 20
Handling discs........................................... 40
SPECIFICATIONS ........................... 41
SOUND ADJUSTMENTS ................... 21
Selecting preset sound modes
(C-EQ: custom equalizer) ....................... 21
Adjusting the sound .................................. 22
Note:
For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on
the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.
BEFORE USE
*For safety....
*Temperature inside the car....
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
If you have parked the car for a long time in hot
or cold weather, wait until the temperature in the
car becomes normal before operating the unit.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF THE BUTTONS
Control panel
Display window
1
(standby/on/attenuator) button
a ∞ (down) button
–10 button
2 SEL (select) button
3 TP PTY (traffic programme/programme type)
button
4 FM/AM DAB button
5 CD CD-CH (CD changer) button
6 Display window
Display window
s Main display
d EQ (equalizer) indicator
f Sound mode (C-EQ: custom equalizer)
indicators—ROCK, CLASSIC, POPS,
HIP HOP, JAZZ, USER
7 0 (eject) button
8 5 (up) button
+10 button
•
also works as level meter during play if
the level meter is activated (see page 25).
9
(control panel release) button
p Control dial
q Number buttons
w EQ (equalizer) button
e Remote sensor
• You can control this receiver with an optionally
purchased remote controller.
r MO (monaural) button
t SSM (Strong-station Sequential Memory)
button
y RPT (repeat) button
u RND (random) button
i MODE button
g MP3 indicator
• Lights up only when playing an MP3 disc on a
JVC MP3-compatible CD changer.
h Tuner reception indicators—ST (stereo),
MO (monaural)
j RDS indicators—TP, PTY, AF, REG
k CD indicator
l CH (CD changer) indicator
/ Playback mode/item indicators—RND (random),
(disc), RPT (repeat)
z LOUD (loudness) indicator
x Source display
o DISP (display) button
;
Volume level indicator
c Tr (track) indicator
4/¢
buttons
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
1
3
2
Volume level appears.
Turning on the power
1 Turn on the power.
Volume level indicator
Note on One-Touch Operation:
When you select a source in step 2 below, the
power automatically comes on. You do not have
to press this button to turn on the power.
4 Adjust the sound as you want. (See
pages 21 and 22.)
2 Select the source.
To drop the volume in a moment
Press
briefly while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.
• If you turn the control dial, you can also restore
the sound.
To operate the tuner (FM or AM),
see pages 8 – 17.
To play a CD,
see pages 18 – 20.
To operate the CD changer,
see pages 27 – 30.
To operate the external component
(LINE IN), see page 31.
To operate the DAB tuner,
see pages 32 – 35.
To turn off the power
Press and hold
second.
“SEE YOU” appears, then the unit turns off.
• If you turn off the power while listening to a
disc, disc play will start from where playback
has been stopped previously, next time you
turn on the power.
for more than one
3 Adjust the volume.
To increase the volume
CAUTION on Volume Setting:
Discs produce very little noise compared with
other sources. If the volume level is adjusted for
the tuner, for example, the speakers may be
damaged by the sudden increase in the output
level. Therefore, lower the volume before playing a
disc and adjust it as required during playback.
To decrease the volume
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Canceling the display
demonstration
3 Select “DEMO OFF.”
When shipped from the factory, display
demonstration has been activated, and starts
automatically when no operations are done for
about 20 seconds.
DEMO OFF
DEMO ON
• It is recommended to cancel the display
demonstration before you use the unit for the
first time.
To cancel the display demonstration, follow
the procedure below:
4 Finish the setting.
1 Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 23 and 24.)
To activate the display demonstration, repeat
the same procedure and select “DEMO ON” in
step 3.
2 Select “DEMO” if not shown on the
display.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the clock
5 Finish the setting.
You can also set the clock system to either
24 hours or 12 hours.
1 Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 23 and 24.)
To check the current clock time or change the
display mode
Press DISP (display) repeatedly.
Each time you press the button,
the display changes as follows:
• During AM and FM non-RDS Station
operation:
2 Set the hour.
1 Select “CLOCK H” (hour) if not shown on
the display.
Frequency
Clock
2 Adjust the hour.
1
2
• During FM RDS Station operation:
Station name Station frequency
Clock
Programme type
3 Set the minute.
• During CD operation:
1 Select “CLOCK M” (minute).
2 Adjust the minute.
Elapsed playing time
Clock
1
2
• During CD changer operation:
Disc number
Clock
Elapsed playing time
• During external component operation:
4 Set the clock system.
1 Select “24H/12H.”
LINE IN
Clock
2 Select “24H” or “12H.”
• During power off:
The power turns on and the clock time is
1
2
shown for 5 seconds, then the power turns off.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
RADIO OPERATIONS
To stop searching before a station is
received, press the same button you have
pressed for searching.
Listening to the radio
You can use either automatic searching or manual
searching to tune in to a particular station.
Searching for a station manually:
Manual search
Searching for a station automatically:
Auto search
1 Select the band (FM1 – 3, AM).
Each time you press the
button, the band changes as
follows:
1 Select the band (FM1 – 3, AM).
Each time you press the
button, the band changes as
follows:
FM1
FM2
FM3
AM
FM1
FM2
FM3
AM
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
Selected band appears.
2 Press and hold ¢
or
4
until “M” (manual) starts flashing on
the display.
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
2 Start searching for a station.
To search for stations of
higher frequencies
To search for stations of lower frequencies
When a station is received, searching stops.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing stations in memory
3 Tune in to a station you want while
“M” (manual) is still flashing.
You can use one of the following two methods to
store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strong-
station Sequential Memory)
To tune in to stations of
higher frequencies
• Manual preset of both FM and AM stations
To tune in to stations of lower frequencies
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM
band (FM1, FM2, and FM3).
• If you release your finger from the button,
the manual mode will automatically turns
off after 5 seconds.
• If you hold down the button, the frequency
keeps changing (in 50 kHz intervals for
FM and 9 kHz for AM—MW/LW) until you
release the button.
1 Select the FM band (FM1 – 3) you
want to store FM stations into.
Each time you press the
button, the band changes as
follows:
When an FM stereo broadcast is hard to
receive:
FM1
FM2
FM3
AM
1 Press MODE to enter the
functions mode while listening
to an FM stereo broadcast.
2 Press MODE to enter the functions
mode.
2 Press MO (monaural), while
“MODE” is still flashing on the
display, so that “MONO”
appears on the display.
Each time you press the button,
monaural mode turns on and off
alternately.
3 Press and hold SSM for about
2 seconds.
MO (monaural) indicator
When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved.
“SSM” flashes, then disappears
when automatic preset is over.
Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2, or FM3).
These stations are preset in the number buttons
—No.1 (lowest frequency) to No.6 (highest
frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual preset
You can preset up to 6 stations in each band
(FM1, FM2, FM3, and AM) manually.
4 Repeat the above procedure to store
other stations into other preset
numbers.
Ex.: Storing FM station of 92.5 MHz into the
preset number 1 of the FM1 band.
Notes:
• A previously preset station is erased when a new
station is stored in the same preset number.
• Preset stations are erased when the power supply to
the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset
the stations again.
1 Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).
Each time you press the
button, the band changes as
follows:
Tuning in to a preset station
FM1
FM2
FM3
AM
You can easily tune in to a preset station.
Remember that you must store stations first. If
you have not stored them yet, see “Storing
stations in memory” on pages 9 and 10.
2 Tune in to a station (in this example,
of 92.5 MHz).
To tune in to stations of
higher frequencies
1 Select the band (FM1 – 3, AM).
Each time you press the
button, the band changes as
follows:
To tune in to stations of lower frequencies
FM1
FM2
FM3
AM
2 Select the number (1 – 6) for the
preset station you want.
3 Press and hold the number button
(in this example, 1) for more than
2 seconds.
Preset number flashes for a while.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
RDS OPERATIONS
To use Network-Tracking Reception
What you can do with RDS
You can select the different modes of network-
tracking reception to continue listening to the
same programme in its finest reception.
RDS (Radio Data System) allows FM stations to
send an additional signal along with their regular
programme signals. For example, the stations
send their station names, as well as information
about what type of programme they broadcast,
such as sports or music, etc.
Another advantage of RDS function is called
“Enhanced Other Networks.” By using the
Enhanced Other Networks data sent from a
station, you can tune in to a different station of a
different network broadcasting your favorite
programme or traffic announcement while
listening to another programme or to another
source such as CD.
When shipped from the factory, “AF” is selected.
• AF:
Network-Tracking Reception is
activated with Regionalization set to
“off.”
With this setting, the unit switches to
another station within the same
network when the received signals
from the current station become
weak. (In this mode, the programme
may differ from the one currently
received.)
The AF indicator lights up but the
REG indicator does not.
By receiving the RDS data, this unit can do the
following:
• Tracing the same programme automatically
(Network-Tracking Reception)
• Standby Reception of TA (Traffic
Announcement) or your favorite programme
• PTY (Programme Type) search
• Programme search
• AF REG: Network-Tracking Reception is
activated with Regionalization set to
“on.”
With this setting, the unit switches to
another station, within the same
network, broadcasting the same
programme when the received
signals from the current station
become weak.
• And some other functions
Tracing the same programme
automatically (Network-Tracking
Reception)
Both the AF indicator and the REG
indicator light up.
• OFF:
Network-Tracking Reception is
deactivated.
Neither the AF indicator nor the REG
indicator lights up.
When driving in an area where FM reception is
not good, the tuner built in this unit automatically
tunes in to another RDS station, broadcasting the
same programme with stronger signals. So, you
can continue to listen to the same programme in
its finest reception, no matter where you drive.
(See the illustration on page 17.)
Two types of the RDS data are used to make
Network-Tracking Reception work correctly
—PI (Programme Identification) and AF
(Alternative Frequency).
Without receiving these data correctly from the
RDS station you are listening to, Network-
Tracking Reception will not operate.
AF and REG indicators
Note:
If a DAB tuner is connected and Alternative Reception
(for DAB services) is activated, Network-Tracking
Reception is also activated (“AF”) automatically. On
the other hand, Network-Tracking Reception cannot
be deactivated without deactivating Alternative
Reception. (See page 35.)
CONTINUED ON THE NEXT PAGE
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using TA Standby Reception
1 Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 23 and 24.)
TA Standby Reception allows the unit to switch
temporarily to Traffic Announcement (TA) from
the current source (another FM station, CD, or
other connected components).
• TA Standby Reception will not work if you are
listening to an AM station.
Press TP PTY to activate TA Standby Reception.
2 Select “AF-REG” (alternative
frequency/regionalization reception)
if not shown on the display.
7 When the current source is FM, the TP
indicator either lights up or flashes.
• If the TP indicator lights up, TA Standby
Reception is activated.
3 Select the desired mode—“AF,”
If a station starts broadcasting a traffic
announcement, “TRAFFIC” appears on the
display, and this unit automatically tunes in to
the station. The volume changes to the
preset TA volume level (see page 16) and the
traffic announcement can be heard.
“AF REG,” or “OFF.”
• If the TP indicator flashes, TA Standby
Reception is not yet activated since the
station being received does not provide the
signals used for TA Standby Reception.
To activate TA Standby Reception, you need
to tune in to another station providing these
4 Finish the setting.
signals. Press ¢
or
4 to search
for such a station.
When a station providing these signals is
tuned in, the TP indicator stops flashing and
remains lit. Now TA Standby Reception is
activated.
7 When the current source is other than FM,
the TP indicator lights up.
If a station starts broadcasting a traffic
announcement, “TRAFFIC” appears on the
display, and this unit automatically changes the
source and tunes in to the station.
To deactivate the TA Standby Reception,
press TP PTY again. The TP indicator
disappears.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using PTY Standby Reception
4 Finish the setting.
PTY Standby Reception allows the unit to switch
temporarily to your favorite programme (PTY:
Programme Type) from the current source
(another FM station, CD, or other connected
components).
• PTY Standby Reception will not work if you are
listening to an AM station.
7 When the current source is FM, the PTY
indicator either lights up or flashes.
• If the PTY indicator lights up, PTY Standby
Reception is activated.
You can select your favorite programme type for
PTY Standby Reception.
When shipped from the factory, PTY Standby
Reception is turned off. (“OFF” is selected for
PTY Standby Reception.)
If a station starts broadcasting the selected
PTY programme, this unit automatically
tunes in to the station.
• If the PTY indicator flashes, PTY Standby
Reception is not yet activated since the
station being received does not provide the
signals used for PTY Standby Reception.
To activate PTY Standby Reception, you
need to tune in to another station providing
1 Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 23 and 24.)
these signals. Press ¢
or
4 to
search for such a station.
When a station providing these signals is
tuned in, the PTY indicator stops flashing
and remains lit. Now PTY Standby Reception
is activated.
2 Select “PTY-STBY” (standby) if not
shown on the display.
7 When the current source is other than FM,
the PTY indicator lights up.
If a station starts broadcasting the selected
PTY programme, this unit automatically
changes the source and tunes in to the station.
3 Select one of the twenty-nine PTY
To deactivate the PTY Standby Reception,
select “OFF” in step 3 on the left column. The
PTY indicator disappears.
codes. (See page 17.)
Selected code name
appears on the display
and is stored into
memory.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching your favorite programme
3 Press and hold the number button
for more than 2 seconds to store the
PTY code selected into the preset
number you want.
You can search any one of the PTY codes.
In addition, you can store your 6 favorite
programme types in the number buttons.
When shipped from the factory, the following
6 programme types have been stored in the
number buttons (1 to 6).
To store your favorite programme types, see
below.
To search your favorite programme type, see
page 15.
3
1
2
POP M
ROCK M
EASY M
6
4
5
Selected PTY code and
“MEMORY” appear
CLASSICS
AFFAIRS
VARIED
alternately for a while.
To store your favorite programme types
1 Press and hold TP PTY for more
than 2 seconds while listening to an
FM station.
4 Press and hold TP PTY for more
than 2 seconds to exit from this
mode.
The last selected PTY code appears.
2 Select one of the twenty-nine PTY
codes. (See page 17.)
Selected code name
appears on the display.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
To search your favorite programme type
3 Press ¢
or
4 to start PTY
search for your favorite programme.
1 Press and hold TP PTY for more
than 2 seconds while listening to an
FM station.
• If there is a station broadcasting a programme
of the same PTY code as you selected, that
station is tuned in.
The last selected PTY code appears.
• If there is no station broadcasting a
programme of the same PTY code as you
selected, the station will not change.
2 To select one of your favorite
programme type
Note:
In some areas, the PTY search will not work correctly.
or
To select any one of the twenty-nine
PTY codes
Ex.: When “ROCK M” is selected
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the TA volume level
Other convenient RDS
You can preset the volume level for TA Standby
Reception. When a traffic programme is received,
the volume level automatically changes to the
preset level.
• See also “Changing the general settings
(PSM)” on page 23.
functions and adjustments
Automatic selection of the station
when using the number buttons
Usually when you press the number button, the
preset station is tuned in.
1 Press and hold SEL (select) for more than
2 seconds so that one of the PSM items
appears on the display.
However, when the preset station is an RDS
station, something different will happen. If the
signals from that preset station are not sufficient
for good reception, this unit, using the AF data,
tunes in to another frequency broadcasting the
same programme as the original preset station is
broadcasting. (Programme search)
2 Press ¢
(volume).
or
4 to select “TA VOL”
3 Turn the control dial to set to the desired
volume.
You can set it from “VOL 00” to “VOL 30” or
“VOL 50” (depending on the amplifier gain
control setting: see page 25).
• The unit takes some time to tune in to another
station using programme search.
4 Press SEL (select) to finish the setting.
To activate programme search, follow the
procedure below.
• See also “Changing the general settings
(PSM)” on page 23.
Automatic clock adjustment
When shipped from the factory, the clock built in
this unit is set to be readjusted automatically
using the CT (Clock Time) data in the RDS
signal.
If you do not want to use automatic clock
adjustment, follow the procedure below.
• See also “Changing the general settings
(PSM)” on page 23.
1 Press and hold SEL (select) for more than
2 seconds so that one of the PSM items
appears on the display.
2 Press ¢
or
4 to select
“P(Programme)-SEARCH.”
3 Turn the control dial clockwise to select “ON.”
Now programme search is activated.
4 Press SEL (select) to finish the setting.
1 Press and hold SEL (select) for more than
2 seconds so that one of the PSM items
appears on the display.
To cancel programme search, repeat the same
procedure and select “OFF” in step 3 by turning
the control dial counterclockwise.
2 Press ¢
or
4 to select “AUTO
ADJ” (adjustment).
3 Turn the control dial counterclockwise to select
“OFF.”
Now automatic clock adjustment is canceled.
4 Press SEL (select) to finish the setting.
To reactivate clock adjustment, repeat the
same procedure and select “ON” in step 3 by
turning the control dial clockwise.
Note:
You must stay tuned to the same station for more than
2 minutes after setting “AUTO ADJ” to “ON.”
Otherwise, the clock time will not be adjusted. (This is
because the unit takes up to 2 minutes to capture the
CT data in the RDS signal.)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
PTY codes
NEWS:
AFFAIRS:
News
SOCIAL:
Programmes on social
activities
Topical programmes expanding
on current news or affairs
Programmes which impart
advice on a wide variety of topics
Sport events
RELIGION: Programmes dealing with any
aspect of belief or faith, or the
INFO:
nature of existence or ethics
SPORT:
PHONE IN: Programmes where people can
express their views either by
EDUCATE: Educational programmes
DRAMA: Radio plays
phone or in a public forum
CULTURE: Programmes on national or
regional culture
TRAVEL:
LEISURE:
JAZZ:
Programmes about travel
destinations, package tours,
and travel ideas and
opportunities
Programmes concerned with
recreational activities such as
gardening, cooking, fishing,
etc.
SCIENCE:
Programmes on natural science
and technology
VARIED:
Other programmes like comedies
or ceremonies
POP M:
Pop music
ROCK M:
EASY M:
LIGHT M:
Rock music
Easy-listening music
Light music
Jazz music
COUNTRY: Country music
NATION M: Current popular music from
another nation or region, in that
country’s language
OLDIES:
FOLK M:
CLASSICS: Classical music
OTHER M: Other music
WEATHER: Weather information
FINANCE: Reports on commerce, trading,
the Stock Market, etc.
Classic pop music
Folk music
CHILDREN: Entertainment programmes for
children
DOCUMENT: Programmes dealing with
factual matters, presented in an
investigative style
The same programme can be received on different frequencies.
Programme 1
broadcasting on
frequency A
Programme 1
broadcasting on
frequency E
Programme 1
broadcasting on
frequency B
Programme 1
broadcasting on
frequency C
Programme 1
broadcasting on
frequency D
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CD OPERATIONS
The display changes to show the following:
Current source indication
Playing a CD
1 Open the control panel.
CD indicator
Note on One-Touch Operation:
Total playing time Total track number
of the inserted disc of the inserted disc
When a CD is already in the loading slot,
pressing CD CD-CH turns on the unit and starts
playback automatically.
2 Insert a CD into the loading slot.
The unit turns on,
draws the CD and
starts playback
automatically.
Current track
Elapsed playing time number
3 Close the control panel by hand.
Notes:
• When a CD is inserted upside down, the CD
automatically ejects (if the control panel is open).
If the control panel is closed, the source changes to
the previously selected source, “PLEASE” and
“EJECT” appear alternately on the display.
• If there is no CD in the loading slot, you cannot
select CD as the source. “NO DISC” appears on
the display.
All tracks will be played repeatedly until you
stop playback.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop play and eject the CD
To go to a particular track directly
Press 0.
Press the number button corresponding to the
track number to start its playback.
CD play stops and the control panel flips down.
The CD automatically ejects from the loading
slot. The source changes to the previously
selected source.
• If you change the source, CD play also stops
(without ejecting the CD).
Next time you select “CD” as the source, CD
play starts from where playback has been
stopped previously.
• To select a track number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a track number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than one
second.
Notes:
• If the ejected CD is not removed for about
15 seconds, the CD is automatically inserted again
into the loading slot to protect it from dust.
(CD play will not start this time.)
To go to a track quickly (+10 and –10
buttons)
• You can eject the CD even when the unit is turned off.
1
Press MODE to enter the functions mode
while playing a CD.
Locating a track or a
particular portion on a CD
To fast-forward or reverse the track
Press and hold ¢
playing a CD, to fast-forward the
track.
, while
2
Press +10 or –10.
To skip 10 tracks* forwards to
the last track
Press and hold
reverse the track.
4, while playing a CD, to
To skip 10 tracks* backwards to
the first track
* First time you press +10 or –10 button, the
track skips to the nearest higher or lower
track with a track number of multiple ten (ex.
10th, 20th, 30th).
Then each time you press the button, you can
skip 10 tracks (see “How to use the +10 and
–10 buttons” on page 20).
To go to the next or previous tracks
Press ¢
briefly, while
playing a CD, to go ahead to the
beginning of the next track.
Each time you press the button
consecutively, the beginning of
the next tracks is located and
played back.
• After the last track, the first track will be
selected, and vice versa.
Press
4 briefly, while playing a CD, to go
back to the beginning of the current track.
Each time you press the button consecutively,
the beginning of the previous tracks is located
and played back.
CONTINUED ON THE NEXT PAGE
19
Download from Www.Somanuals.com. All Manuals Search And Download.
To play back tracks repeatedly
(Track Repeat Play)
How to use the +10 and –10 buttons
• Ex. 1: To select track number 32 while
You can play back the current track repeatedly.
playing track number 6
1 Press MODE to enter the functions
mode while playing a CD.
2 Press RPT (repeat), while
“MODE” is still flashing on the
display, so that “TRK RPT”
appears on the display.
Each time you press the button,
track repeat play mode turns on
and off alternately.
(Three times)
Track 6 \ 10 \ 20 \ 30 \ 31 \ 32
(Twice)
• Ex. 2 :To select track number 8 while
playing track number 36
(Three times)
(Twice)
Track 36 \ 30 \ 20 \ 10 \ 9 \ 8
RPT indicator
When track repeat play is turned on, the RPT
indicator lights up on the display. The current
track starts playing repeatedly.
Selecting CD playback modes
To play back tracks at random
(Disc Random Play)
Prohibiting CD ejection
You can play back all tracks on the CD at random.
You can prohibit CD ejection and can lock a CD
in the loading slot.
1 Press MODE to enter the functions
mode while playing a CD.
While pressing CD CD-CH, press and hold
for more than 2 seconds.
2 Press RND (random), while
“MODE” is still flashing on the
display, so that “DISC RND”
appears on the display.
Each time you press the button,
disc random play mode turns on
and off alternately.
“NO EJECT” flashes on the display for about
5 seconds, and the CD is locked and cannot be
ejected.
RND and
(disc) indicators
To cancel the prohibition and unlock the
CD
While pressing CD CD-CH, press and hold
again for more than 2 seconds.
When disc random play is turned on, the RND
and indicators light up on the display. A track
randomly selected starts playing.
“EJECT OK” flashes on the display for about
5 seconds, and the CD is unlocked.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SOUND ADJUSTMENTS
Indication pattern changes for each
sound mode except for “USER.”
Selecting preset sound modes
(C-EQ: custom equalizer)
You can select a preset sound mode (C-EQ:
custom equalizer) suitable to the music genre.
Ex.: When you select “ROCK”
• There is a time limit in doing the following
procedure. If the setting is canceled before you
finish, start from step 1 again.
Indication
For:
Preset values
BAS TRE LOUD
1 Press MODE to enter the functions
USER
ROCK
(Flat sound)
00
00
OFF
ON
mode.
Rock or
+03
+01
disco music
CLASSIC Classical
music
+01
–02
OFF
POPS
Light music
+04
+02
+01
00
OFF
ON
2 Press EQ (equalizer) while “MODE”
HIP HOP Funk or rap
music
is still flashing on the display.
You can confirm the current
sound mode.
JAZZ
Jazz music
+02
+03
OFF
Note:
You can adjust each sound mode to your preference.
Once you make an adjustment, it is automatically
stored for the currently selected sound mode. See
“Adjusting the sound” on page 22.
3 Select the sound mode you want.
Each time you press the
button, the sound modes
change as follows:
USER
JAZZ
ROCK
CLASSIC
HIP HOP
POPS
ROCK
USER
JAZZ
CLASSIC
POPS
HIP HOP
21
Download from Www.Somanuals.com. All Manuals Search And Download.
1
*
When you adjust the bass, treble, or loudness, the
adjustment you have made is stored for the
currently selected sound mode (C-EQ) including
“USER.”
If you are using a two-speaker system, set the fader
level to “00.”
Normally the control dial works as the volume
control. So you do not have to select “VOL” to
adjust the volume level.
Depending on the amplifier gain control setting.
(See page 25 for details.)
Adjusting the sound
You can adjust the sound characteristics to your
preference.
2
3
*
1 Select the item you want to adjust.
*
Each time you press the
button, the adjustable items
change as follows:
4
*
2 Adjust the setting.
BAS
TRE
FAD
(bass)
(treble)
(fader)
To increase the level or
turn on the loudness
VOL
LOUD
BAL
(volume)
(loudness)
(balance)
To decrease the level or
turn off the loudness
Indication
To do:
Range
BAS*1
Adjust the bass. –06 (min.)
Indication pattern changes as
you adjust the bass or treble.
|
+06 (max.)
TRE*1
FAD*2
BAL
Adjust the treble. –06 (min.)
|
+06 (max.)
Adjust the front
and rear speaker
balance.
R06 (Rear only)
|
F06 (Front only)
Ex. 1: When you adjust “TRE” (treble)
Adjust the left
and right speaker
balance.
L06 (Left only)
|
R06 (Right only)
LOUD*1
Boost low and
high frequencies
to produce a well-
balanced sound
at low volume
level.
Ex. 2: When you turn on the loudness
LOUD ON
|
LOUD OFF
3 Repeat steps 1 and 2 to adjust the
other items.
VOL*3
Adjust the volume. 00 (min.)
|
To reset each sound mode to the factory
settings, repeat the same procedure and
reassign the preset values listed in the table on
page 21.
30 or 50 (max.)*4
22
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER MAIN FUNCTIONS
Changing the general settings
(PSM)
3 Adjust the PSM item selected.
You can change the items listed in the table
below and on page 24 by using the PSM
(Preferred Setting Mode) control.
Basic Procedure
4 Repeat steps 2 and 3 to adjust the
1 Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(See below and page 24.)
other PSM items if necessary.
5 Finish the setting.
2 Select the PSM item you want to
adjust.
Preferred Setting Mode (PSM) items
• For detailed operations of each PSM items, refer to the pages listed in the table.
Factory-preset See
Indications
Selectable values/items
DEMO ON
0 — 23 (1 — 12)
00 — 59
settings
page
6
DEMO
Display demonstration
Hour adjustment
DEMO OFF
DEMO ON
CLOCK H
CLOCK M
24H/12H
0 (0:00)
00 (0:00)
24H
7
Minute adjustment
24/12-hour time display
12H
OFF
24H
ON
7
AUTO ADJ Automatic clock setting
ON
16
AF
AF REG
AF-REG
Alternative frequency/
Regionalization reception
AF
11, 12
OFF*1
1
*
Displayed only when the “DAB AF” is set to “OFF.”
CONTINUED ON THE NEXT PAGE
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Factory-preset See
Indications
Selectable values/items
settings
page
29 programme types
PTY-STBY PTY standby
OFF
OFF
13
(see page 17)
TA VOL
Traffic announcement
volume
VOL 00 — VOL 30 or 50*2
VOL 20
OFF
16
16
35
P-SEARCH Programme search
OFF
ON
DAB AF*3
Alternative frequency
search
AF OFF
AF ON
AF ON
DAB VOL*3 DAB volume adjustment
VOL –12 — VOL 12
VOL 00
ON
35
25
OFF
ON
LEVEL
Level display
AUTO
OFF
DIMMER
Dimmer mode
AUTO
OFF
25
25
ON
OFF
MUTING 1
TEL
Telephone muting
MUTING 2
EXT IN*4
External component
CHANGER
LOW PWR
LINE IN
CHANGER
HIGH PWR
25
25
AMP GAIN Amplifier gain control
HIGH PWR
2
3
4
*
*
*
Depending on the amplifier gain control setting. (See page 25 for details.)
Displayed only when the DAB tuner is connected.
Displayed only when one of the following sources is selected—FM, AM, and CD.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
To select the level meter—LEVEL
You can activate or deactivate the level meter
according to your preference.
When shipped from the factory, level meter is
activated.
To select the external component to use
—EXT IN
You can connect the external component to the
CD changer jack on the rear using the Line Input
Adapter KS-U57 (not supplied).
To use the external component as the playback
source through this unit, you need to select
which component—CD changer or external
component—to use.
• ON:
• OFF:
Shows the audio level indicator.
Cancels the audio level indicator;
sound mode indicator is shown.
When shipped from the factory, CD changer is
selected as the external component.
To select the dimmer mode—DIMMER
• CHANGER: To use the CD changer.
When you turn on the car headlights, the display
automatically dims (Auto Dimmer).
When shipped from the factory, Auto Dimmer
mode is activated.
• LINE IN:
To use the external component
other than CD changer.
Note:
For connecting the Line Input Adapter KS-U57 and
the external component, refer to the Installation/
Connection Manual (separate volume).
• AUTO:
• OFF:
• ON:
Activates Auto Dimmer.
Cancels Auto Dimmer.
Always dims the display.
Note:
To select the amplifier gain control
—AMP GAIN
You can change the maximum volume level of
this unit. When the maximum power of the
speakers is less than 50 W, select “LOW PWR”
to prevent them from being damaged.
When shipped from the factory, “HIGH PWR” is
selected.
Auto Dimmer equipped for this unit may not work
correctly on some vehicles, particularly on those
having a control dial for dimming.
In this case, set the dimmer mode to “ON” or “OFF.”
To select the telephone muting—TEL
This mode is used when a cellular phone system
is connected. Depending on the phone system
used, select either “MUTING 1” or “MUTING 2”
whichever mutes the sounds from this unit.
When shipped from the factory, this mode is
deactivated.
• LOW PWR: You can adjust the volume level
from “VOL 00” to “VOL 30.”
Note:
If you can change the setting from
“HIGH PWR” to “LOW PWR” while
listening at a volume level more than
30, the unit automatically changes the
volume level to “VOL 30.”
• MUTING 1: Select if this setting can mute the
sounds.
• MUTING 2: Select if this setting can mute the
sounds.
• OFF:
• HIGH PWR:You can adjust the volume level
from “VOL 00” to “VOL 50.”
Cancels the telephone muting.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the control panel
Detaching the control panel
1 Insert the right side of the control
panel into the groove on the panel
holder.
You can detach the control panel when leaving
the car.
When detaching or attaching the control panel,
be careful not to damage the connectors on the
back of the control panel and on the panel
holder.
Detaching the control panel
Before detaching the control panel, be sure to
turn off the power.
1 Unlock the control panel.
2 Press the left side of the control
panel to fix it to the panel holder.
2 Pull the control panel out of the unit.
Note on cleaning the connectors:
If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened
with alcohol, being careful not to damage the
connectors.
3 Put the detached control panel into
the provided case.
Connectors
26
Download from Www.Somanuals.com. All Manuals Search And Download.
CD CHANGER OPERATIONS
We recommend that you use the JVC MP3-
compatible CD changer with your unit.
About MP3 discs
MP3 “files (tracks)” can be recorded in “folders”
—in PC terminology.
During recording, the files and folders can be
arranged in a way similar to arranging files and
folders of computer data.
“Root” is similar to the root of a tree. Every file
and folder can be linked to and be accessed from
the root.
By using this CD changer, you can play back
your original CD-Rs (Recordable) and CD-RWs
(Rewritable) recorded either in audio CD format
or in MP3 format.
• You can also connect other CH-X series
CD changers (except CH-X99 and CH-X100).
However, they are not compatible with MP3
discs, so you cannot play back MP3 discs.
• You cannot use the KD-MK series CD
changers with this unit.
Hierarchy
Level 1
ROOT
Level 2
Level 3
Level 4
Level 5
Before operating your CD changer:
• Refer also to the Instructions supplied for
your CD changer.
6
7
01
02
03
4
3
• If no discs are in the magazine of the CD
changer or the discs are inserted upside
down, “NO DISC” will appear on the display.
If this happens, remove the magazine and
set the discs correctly.
05
10
5
11
12
04
1
8
9
2
• If no magazine is loaded in the CD changer,
“NO MAG” appears on the display. If this
happens, insert the magazine in the CD
changer.
• If “RESET 1” – “RESET 8” appears on the
display, something is wrong with the
connection between this unit and the CD
changer. If this happens, check the
connection and make sure the cords are
connected firmly. Then, press the reset
button of the CD changer.
: Folders and their playback order
: MP3 files and their playback order
01
1
27
Download from Www.Somanuals.com. All Manuals Search And Download.
• When the current disc is a CD:
Playback starts from the first track of the
current disc.
Playing discs
Select the CD changer (CD-CH).
CD
CD-CH*
* If you have changed “EXT IN” setting to “LINE IN”
(see page 25), you cannot select the CD changer.
Selected disc number
• When the current disc is an MP3 disc:
Playback starts from the first folder of the
current disc once file check is completed.
Current track
Elapsed playing time number
Selected disc Total folder
number
number
Notes:
• When you press CD CD-CH, the power
automatically comes on. You do not have to press
to turn on the power.
MP3 indicator
Selected track number
• If you change the source, CD changer play also
stops. Next time you select the CD changer as the
source, CD changer play starts from where
playback has been stopped previously.
Elapsed playing time
To go to a particular disc directly
Press the number button corresponding to the
disc number to start its playback (while the CD
changer is playing).
• To select a disc number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a disc number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than
one second.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
* First time you press +10 or –10 button, the
track/file skips to the nearest higher or lower
track/file with a track/file number of multiple
ten (ex. 10th, 20th, 30th).
To fast-forward or reverse the track/file
Press and hold ¢
, during
play, to fast-forward the track/file.
Then each time you press the button, you can
skip 10 tracks/files (see “How to use the +10
and –10 buttons” below).
• After the last track/file, the first track/file will
be selected, and vice versa.
Press and hold
the track/file.
4, during play, to reverse
Note:
During this operation, you can only hear intermittent
sounds. (The elapsed playing time also changes
intermittently on the display.)
Note:
If the current playing disc is an MP3 disc, files are
skipped within the same folder.
To go to the next or previous tracks/files
How to use the +10 and –10 buttons
Press ¢
to skip ahead to the beginning of
the next track/file.
briefly during play,
• Ex. 1: To select track/file number 32 while
playing track/file number 6
Each time you press the button
consecutively, the beginning of
the next tracks/files is located
and played back.
(Three times)
(Twice)
Track/File 6 \ 10 \ 20 \ 30 \ 31 \ 32
Press
4 briefly during play, to skip back to
the beginning of the current track/file.
Each time you press the button consecutively,
the beginning of the previous tracks/files is
located and played back.
• Ex. 2 :To select track/file number 8 while
playing track/file number 36
(Three times)
(Twice)
This operation is only possible when
using JVC MP3-compatible CD changer
(CH-X1500).
Track/File 36 \ 30 \ 20 \ 10 \ 9 \ 8
To skip to the next or previous folder
(only for MP3 discs)
To go to a track/file quickly (+10 and –10
buttons)
1 Press MODE to enter the functions mode
Press 5 (up) while playing an MP3
disc, to go to the next folder.
Each time you press the button
consecutively, the next folder is
located, and the first file in the
folder starts playback.
while playing a disc.
2 Press +10 or –10.
Press ∞ (down) while playing an MP3 disc, to go
to the previous folder.
Each time you press the button consecutively,
the previous folder is located, and the first file in
the folder starts playback.
To skip 10 tracks/files*
forwards to the last track/file
To skip 10 tracks/files*
backwards to the first track/file
29
Download from Www.Somanuals.com. All Manuals Search And Download.
To play back tracks/files repeatedly
(Track Repeat/Disc Repeat Play)
Selecting the playback modes
To play back tracks/files at random
(Disc Random/Magazine Random Play)
1 Press MODE to enter the functions
mode during play.
1 Press MODE to enter the functions
mode during play.
2 Press RPT (repeat), while
“MODE” is still flashing on the
display.
Each time you press the button, the
repeat play mode changes as
follows:
2 Press RND (random), while
“MODE” is still flashing on the
display.
Each time you press the button, the
random play mode changes as
follows:
TRK RPT
DISC RPT
Canceled
DISC RND
MAG RND
Canceled
RPT indicator
Ex.: When you select “TRK RPT”
RND and
(disc) indicators
Note:
Ex.: When you select “DISC RND”
MP3 indicator also lights up if the current playing disc
is an MP3 disc.
Note:
MP3 indicator also lights up if the current playing disc
is an MP3 disc.
Active
indicator
Mode
Plays repeatedly
Active
indicator
TRK RPT
RPT indicator The current (or
Mode
Plays at random
lights up.
specified) track/
file.
DISC RND RND and
indicators
All tracks/files of
the current (or
specified) disc.
DISC RPT
and RPT All tracks/files of
indicators light the current (or
light up.
up.
specified) disc.
MAG RND RND indicator All tracks/files of
lights up. the inserted discs.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL COMPONENT OPERATIONS
Playing an external component
2 Turn on the connected component
and start playing the source.
You can connect the external components to the
CD changer jack on the rear using the Line Input
Adapter KS-U57 (not supplied).
3 Adjust the volume.
Preparations:
• For connecting the Line Input Adapter KS-U57 and
the external component, refer to the Installation/
Connection Manual (separate volume).
• Before operating the external component using the
following procedure, select the external input
correctly. (See “To select the external component to
use—EXT IN” on page 25.)
4 Adjust the sound as you want. (See
pages 21 and 22.)
1 Select the external component
(LINE IN).
CD
LINE IN*
• If “LINE IN”* does not appear on the display,
see page 25 and select the external input
(“LINE IN”).
* Displayed only when one of the following sources is
selected—FM, AM, and CD.
Note on One-Touch Operation:
When you press CD CD-CH, the power automatically
comes on. You do not have to press
on the power.
to turn
31
Download from Www.Somanuals.com. All Manuals Search And Download.
DAB TUNER OPERATIONS
We recommend that you use DAB (Digital Audio
Broadcasting) tuner KT-DB1500 or KT-DB1000
with your unit.
If you have another DAB tuner, consult your JVC
IN-CAR ENTERTAINMENT dealer.
• Refer also to the Instructions supplied for your
DAB tuner.
Tuning in to an ensemble and
one of the services
A typical ensemble has 6 or more programmes
(services) broadcast at the same time. After
tuning in to an ensemble, you can select a
service you want to listen to.
Before you start....
Press FM/AM DAB briefly if CD, CD changer, or
external component is the current source.
What is DAB system?
DAB is one of the digital radio broadcasting
systems available today. It can deliver CD
quality sound without any annoying
interference and signal distortion.
Furthermore, it can carry text, pictures, and
data.
In contrast to FM broadcast, where each
programme is transmitted on its own
frequency, DAB combines several
programmes (called “services”) to form one
“ensemble.”
1 Select the DAB tuner.
Each time you press and
hold the button, the DAB
tuner and the FM/AM tuner
are alternately selected.
DAB
FM/AM
2 Select the DAB band (DAB1, DAB2,
In addition, each “service”—called “primary
service”—can also be divided into its
components (called “secondary service”).
or DAB3) you want.
Each time you press the
button, the DAB band
changes as follows:
With the DAB tuner connected with this unit,
you can enjoy these DAB services.
DAB1
DAB2
DAB3
Note:
Note:
This receiver has three DAB bands (DAB1,
DAB2, DAB3). You can use any of them to tune
in to an ensemble.
When reception switches between DAB and FM, the
listening volume level may increase or decrease
inconveniently. This change in the volume level results
from unequal audio injection levels at broadcaster
site, but not from the malfunction of this unit.
To prevent this inconvenience, you can adjust the DAB
volume level. (See “To adjust the DAB volume level”
on page 35.)
32
Download from Www.Somanuals.com. All Manuals Search And Download.
To tune in to a particular ensemble
without searching
3 Start searching for an ensemble.
To search for ensembles of
higher frequency
Before you start....
Press FM/AM DAB briefly if CD, CD changer, or
external component is the current source.
To search for ensembles of lower frequency
1 Press and hold FM/AM DAB to select DAB
tuner as the source.
2 Press FM/AM DAB repeatedly to select the
DAB band (DAB1, DAB2, or DAB3).
When an ensemble is received, searching
stops.
3 Press and hold ¢
or
4 for more
To stop searching before an ensemble is
received, press the same button you have
pressed for searching.
than one second.
4 Press ¢
or
4 repeatedly until the
ensemble you want is reached.
• If you hold down the button, the frequency
keeps changing until you release the
button.
4 Select a service (either primary or
secondary) you want to listen to.
5 Press 5 (up) or ∞ (down) to select a service
(either primary or secondary) you want to
listen to.
To select the next service (If a
primary service has some
secondary services, they are
selected before the next
To restore the FM/AM tuner
Press and hold FM/AM DAB again.
primary service is selected.)
To select the previous service (either
primary or secondary)
Storing DAB services in
memory
To change the display information while
tuning in to an ensemble
Normally service name is shown on the display.
If you want to check the ensemble name or its
frequency, press DISP (display) repeatedly.
You can preset up to 6 DAB services in each
DAB band (DAB1, DAB2, and DAB3) manually.
Before you start....
Press FM/AM DAB briefly if CD, CD changer, or
external component is the current source.
Each time you press the button,
the following information appears
for a while on the display.
1 Select the DAB tuner.
Each time you press and
hold the button, the DAB
tuner and the FM/AM tuner
are alternately selected.
Service name
Ensemble name
DAB
FM/AM
Channel number
Frequency
Clock
2 Select the DAB band (DAB1, DAB2,
or DAB3) you want.
Each time you press the
button, the DAB band
changes as follows:
DAB1
DAB2
DAB3
CONTINUED ON THE NEXT PAGE
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuning in to a preset DAB
service
3 Tune in to an ensemble you want.
You can easily tune in to a preset DAB service.
Remember that you must store services first. If
you have not stored them yet, see “Storing DAB
services in memory” on pages 33 and 34.
4 Select a service of the ensemble you
want to listen to.
Before you start....
Press FM/AM DAB briefly if CD, CD changer, or
external component is the current source.
To select the next service
To select the previous service
1 Select the DAB tuner.
Each time you press and
hold the button, the DAB
tuner and the FM/AM tuner
are alternately selected.
5 Press and hold the number button
(in this example, 1) for more than
2 seconds to store the selected
service into the preset number you
want.
DAB
FM/AM
2 Select the DAB band (DAB1, DAB2,
or DAB3) you want.
Each time you press the
button, the DAB band
changes as follows:
Selected preset number
DAB1
DAB2
DAB3
3 Select the number (1 – 6) for the
preset DAB service (primary) you
want.
6 Repeat the above procedure to store
other DAB services into other preset
numbers.
Notes:
• You can only preset primary DAB services. If you
store a secondary service, its primary service will
be stored instead.
• A previously preset DAB service is erased when a
new DAB service is stored in the same preset
number.
Note:
If the selected primary service has some secondary
services, pressing the same number button repeatedly
will tune in to the secondary services.
• Preset DAB services are erased when the power
supply to the memory circuit is interrupted (for
example, during battery replacement). If this
occurs, preset the DAB services again.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
To adjust the DAB volume level
What you can do more with
DAB
You can adjust the volume level of DAB tuner
and store it in memory. By adjusting the volume
level properly to match it to the FM sound level,
you will not need to adjust the volume level each
time you change the source.
Tracing the same programme automatically
(Alternative Reception)
When shipped from the factory, DAB volume
level is set at “00.”
• See also “Changing the general settings
(PSM)” on page 23.
You can keep listening to the same programme.
• While receiving a DAB service:
When driving in an area where a service
cannot be received, this unit automatically
tunes in to another ensemble or FM RDS
station, broadcasting the same programme.
• While receiving an FM RDS station:
When driving in an area where a DAB service
is broadcasting the same programme as the
FM RDS station is broadcasting, this unit
automatically tunes in to the DAB service.
1 Press and hold SEL (select) for more than
2 seconds so that one of the PSM items
appears on the display.
2 Press ¢
or
4 to select “DAB VOL”
(volume).
3 Turn the control dial to set to the desired
volume.
You can set it from “VOL –12” to “VOL 12.”
4 Press SEL (select) to finish the setting.
To use Alternative Reception
When shipped from the factory, Alternative
Reception is activated.
• See also “Changing the general settings
(PSM)” on page 23.
1 Press and hold SEL (select) for more than
2 seconds so that one of the PSM items
appears on the display.
2 Press ¢
or
4 to select “DAB AF”
(alternative frequency).
3 Turn the control dial to select the desired
mode.
• AF ON: Traces the programme among
DAB services and FM RDS
stations—Alternative Reception.
The AF indicator lights up on the
display (see page 11).
• AF OFF: Alternative Reception is
deactivated.
4 Press SEL (select) to finish the setting.
Note:
When Alternative Reception (for DAB services) is
activated, Network-Tracking Reception (for RDS
stations: see page 11) is also activated automatically.
On the other hand, Network-Tracking Reception
cannot be deactivated without deactivating
Alternative Reception.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE REMOTE CONTROLLER
This unit can be remotely controlled as instructed
3. Return the battery holder.
here (with an optionally purchased remote
controller). We recommend that you use remote
controller RM-RK50 or RM-RK60 with your unit.
(Ex.: When you are using RM-RK60)
Insert again the battery holder by pushing it
until you hear a clicking sound.
(back side)
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no
obstacle in between.
WARNING:
• Store the battery in a place where children
cannot reach.
If a child accidentally swallows the battery,
consult a doctor immediately.
• Do not recharge, short, disassemble, or heat the
battery or dispose of it in a fire.
Doing any of these things may cause the battery
to give off heat, crack, or start a fire.
• Do not leave the battery with other metallic
materials.
Remote sensor
• Do not expose the remote sensor to strong
light (direct sunlight or artificial lighting).
Doing this may cause the battery to give off
heat, crack, or start a fire.
• When throwing away or saving the battery,
wrap it in tape and insulate; otherwise, the
battery may start to give off heat, crack, or start
a fire.
• Do not poke the battery with tweezers or similar
tools.
Doing this may cause the battery to give off
heat, crack, or start a fire.
Installing the battery
When the controllable range or effectiveness
of the remote controller decreases, replace
the battery.
1. Remove the battery holder.
1) Push out the battery holder in the
direction indicated by the arrow using a
ball point pen or a similar tool.
2) Remove the battery holder.
CAUTION:
DO NOT leave the remote controller in a place
(such as dashboards) exposed to direct sunlight for
a long time. Otherwise, it may be damaged.
(back side)
KD-G302 and KD-G301 are equipped with the
steering wheel remote control function.
If your car is equipped with the steering wheel
remote controller, you can operate the unit
using the controller.
• See the Installation/Connection Manual
(separate volume) for connection to utilize
this function.
2. Place the battery.
Slide the battery into the holder with the
+ side facing upwards so that the battery
is fixed in the holder.
Lithium coin
battery (product
number: CR2025)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
3 • Selects the preset stations (or services)
while listening to the radio (or the DAB
tuner).
Location of the buttons
Each time you press the button, the preset
station (or service) number increases, and
the selected station (or service) is tuned in.
• While playing an MP3 disc on an MP3-
compatible CD changer;
RM-RK60
– Skips to the previous disc if pressed
briefly.
– Skips to the previous folder if pressed
and held.
Note: While playing a CD on a CD changer,
this always skips to the previous disc.
S
4 Selects the sound mode (C-EQ: custom
equalizer).
Each time you press the button, the sound
mode (C-EQ) changes.
5 • Selects the band while listening to the
radio (or the DAB tuner).
Each time you press the button, the band
changes.
• While playing an MP3 disc on an MP3-
compatible CD changer;
– Skips to the next disc if pressed briefly.
– Skips to the next folder if pressed and
held.
1 • Turns on the unit if pressed when the unit
is turned off.
• Turns off the unit if pressed and held until
“SEE YOU” appears on the display.
• Drops the volume level in a moment if
pressed briefly.
Note: While playing a CD on a CD changer,
this always skips to the next disc.
Press again to resume the volume.
6 Selects the source.
Each time you press the button, the source
changes.
2 • Searches for stations while listening to the
radio.
• Selects services while listening to the DAB
tuner if pressed briefly.
• Searches for ensembles while listening to
the DAB tuner if pressed for more than one
second.
7 Functions the same as the control dial on the
main unit.
Note: These buttons do not function for the
Preferred Setting Mode adjustment.
• Fast-forwards or reverses the track/file if
pressed and held while listening to a disc.
• Skips to the beginning of the next track/file
or goes back to the beginning of the
current (or previous) tracks/files if pressed
briefly while listening to a disc.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
What appears to be trouble is not always serious. Check the following points before calling a service
center.
Symptoms
Causes
Remedies
• Sound cannot be heard
from the speakers.
The volume level is set to the
minimum level.
Adjust it to the optimum level.
Connections are incorrect.
Check the cords and
connections.
• This unit does not work
at all.
The built-in microcomputer may
have functioned incorrectly due
to noise, etc.
Press the reset button on the
panel holder after detaching the
control panel. (The clock setting
and preset stations stored in
memory are erased.)
(See page 2.)
• SSM (Strong-station
Sequential Memory)
automatic preset does
not work.
Signals are too weak.
Store stations manually.
• Static noise while
listening to the radio.
The aerial is not connected
firmly.
Connect the aerial firmly.
Insert the CD correctly.
• CD cannot be played
back.
CD is inserted upside down.
• CD-R/CD-RW cannot be CD-R/CD-RW is not finalized.
• Insert a finalized CD-R/
CD-RW.
• Finalize the CD-R/CD-RW
with the component which
you used for recording.
played back.
• Tracks on the CD-R/
CD-RW cannot be
skipped.
• CD cannot be ejected.
CD is locked.
Unlock the CD.
(See page 20.)
• CD sound is sometimes
interrupted.
You are driving on rough roads.
Stop playback while driving on
rough roads.
CD is scratched.
Change the CD.
Connections are incorrect.
Check the cords and
connections.
• “NO DISC” appears on
the display.
No CD in the loading slot.
CD is inserted incorrectly.
Insert a CD into the loading slot.
Insert the CD correctly.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptoms
Causes
Remedies
• “NO DISC” appears on the
display.
No disc is in the magazine.
Insert discs into the
magazine.
Discs are inserted upside down. Insert discs correctly.
The current disc does not
contain any MP3 files.
Insert a disc that contains
MP3 files.
• “NO MAG” appears on the
display.
No magazine is loaded in the
CD changer.
Insert the magazine.
• “RESET 8” appears on the
display.
This unit is not connected to the Connect this unit and the
CD changer correctly.
CD changer correctly and
press the reset button of the
CD changer.
• “RESET 1” – “RESET 7”
appears on the display.
Press the reset button of the
CD changer.
• The CD changer does not
work at all.
The built-in microcomputer may Press the reset button on the
function incorrectly due to
noise, etc.
panel holder after detaching
the control panel. (The clock
setting and preset stations
stored in memory are
erased.) (See page 2.)
About mistracking:
Mistracking may result from driving on extremely rough roads. This does not damage the unit and the disc,
but will be annoying.
We recommend that you stop disc play while driving on such rough roads.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
When playing a CD-R or CD-RW
Handling discs
Before playing back CD-Rs or CD-RWs, read
their instructions or cautions carefully.
• Use only “finalized” CD-Rs or CD-RWs.
• Some CD-Rs or CD-RWs may not be played
back on this unit because of their disc
characteristics, and for the following reasons:
– Discs are dirty or scratched.
This unit has been designed to reproduce CDs,
CD-Rs (Recordable), and CD-RWs (Rewritable).
• This unit is not compatible with MP3 discs,
but can operate a JVC MP3-compatible
CD changer.
– Moisture condensation on the lens inside the
unit.
– The pickup lens inside the unit is dirty.
• CD-RWs may require a longer readout time
since the reflectance of CD-RWs is lower than
that of regular CDs.
• CD-Rs or CD-RWs are susceptible to high
temperatures or high humidity, so do not leave
them inside your car.
• Do not use following CD-Rs or CD-RWs:
– Discs with stickers, labels, or protective seal
stuck to the surface.
How to handle discs
When removing a disc
from its case, press down
the center holder of the case
and lift the disc out, holding
it by the edges.
Center holder
• Always hold the disc by the edges. Do not
touch its recording surface.
When storing a disc into its case, gently insert
the disc around the center holder (with the
printed surface facing up).
• Make sure to store discs into the cases after
use.
– Discs on which labels can be directly printed
by an ink jet printer.
Using these discs under high temperatures or
high humidity may cause malfunctions or
damage to discs. For example,
– Stickers or labels may shrink and warp a
disc.
To keep discs clean
A dirty disc may not be played
correctly. If a disc does become
dirty, wipe it with a soft cloth in a
straight line from center to edge.
– Stickers or labels may be peeled off so discs
cannot be ejected.
– Print on discs may get sticky.
Read instructions or cautions about labels and
printable discs carefully.
To play new discs
New discs may have some rough
spots around the inner and outer
edges. If such a disc is used, this
unit may reject the disc.
To remove these rough spots, rub
the edges with a pencil or ball-point pen, etc.
CAUTIONS:
• Do not insert 8 cm discs (single CDs) into the
loading slot. (Such discs cannot be ejected.)
• Do not insert any disc of unusual shape—like a
heart or flower; otherwise, it will cause a
malfunction.
Moisture condensation
• Do not expose discs to direct sunlight or any
heat source or place them in a place subject to
high temperature and humidity. Do not leave
them in a car.
• Do not use any solvent (for example,
conventional record cleaner, spray, thinner,
benzine, etc.) to clean discs.
Moisture may condense on the lens inside the
CD player in the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the CD player may
malfunction. In this case, eject the disc and leave
the unit turned on for a few hours until the
moisture evaporates.
Sticker
Stick-on
label
Warped
disc
Sticker
Disc
residue
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
CD PLAYER SECTION
AUDIO AMPLIFIER SECTION
Maximum Power Output:
Type: Compact disc player
Front:
Rear:
50 W per channel
50 W per channel
Signal Detection System: Non-contact optical
pickup (semiconductor laser)
Continuous Power Output (RMS):
Number of channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Front:
19 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
19 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
Dynamic Range:
96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit
Rear:
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
GENERAL
Power Requirement:
Tone Control Range:
Bass:
10 dB at 100 Hz
10 dB at 10 kHz
Operating Voltage:
Treble:
DC 14.4 V (11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature: 0°C to +40°C
Dimensions (W × H × D):
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:
2.0 V/20 kΩ load (full scale)
Output Impedance: 1 kΩ
Installation Size (approx.):
182 mm × 52 mm × 150 mm
Panel Size (approx.):
188 mm × 58 mm × 12 mm
Mass (approx.):
TUNER SECTION
Frequency Range:
1.4 kg (excluding accessories)
FM:
AM:
87.5 MHz to 108.0 MHz
(MW) 522 kHz to 1 620 kHz
(LW) 144 kHz to 279 kHz
Design and specifications are subject to change
without notice.
[FM Tuner]
Usable Sensitivity:
11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 30 dB
Capture Ratio: 1.5 dB
[MW Tuner]
Sensitivity: 20 µV
Selectivity: 35 dB
[LW Tuner]
Sensitivity: 50 µV
41
Download from Www.Somanuals.com. All Manuals Search And Download.
|