StorBladeTM
1U SCSI JBOD
4-bay Rackmount Enclosure
Installation Guide
October 3, 2002
•
Revision A
Patent Pending
Download from Www.Somanuals.com. All Manuals Search And Download.
Table
of
Conte
nts
StorBladeTM
SCSI Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Daisy Chaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
ID Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Agency Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Packaging Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Fault Indication Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Audible Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Canister Removal/Insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Drive Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Basic Personality Card Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Setting ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Available ID's . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
ID Conflict . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Daisy-Chaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
SCSI Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
Blower Removal/Insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
StorBladeTM SCSI JBOD Installation Guide Rev A
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
StorBladeTM
Rail Mounting Kit Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
Spare Hardware Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
US Corporate Headquarters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
Manual Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
RAID Controller Manufacturers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
StorBladeTM SCSI JBOD Installation Guide Rev A
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
The 4-bay StorBladeTM 1U SCSI JBOD enclosure is designed for use with a
host system to provide a high-end storage solution. The following is a summary
of the 4-bay 1U enclosure features:
•
The 4-bay StorBladeTM 1U SCSI JBOD Rackmount enclosure is a four
drive enclosure that supports up to four 3.5" LP (Low-Profile) SCA (80-
pin) drives. It supports single-ended, Ultra2 SCSI, and Ultra 160 SCSI.
The SCSI enclosure has two SE/LVD (single-ended/Low Voltage
Differential) Channels.
2/4/6/8/10/12/15-bay Product Family Features
TM
FORTRA and StorBlade are families of high-end enclosures designed for
high-volume performance storage solutions. The following table shows the
features of the FORTRA 2/4/6/8/10/12/15-bay and the StorBladeTM
products:
4-bay1,3 6-bay*1,3 8-bay1 10-bay*1,2
15-bay*1,3
2-bay
12-bay
StorBlade
Number of Device Bays
2
1
4
1
6
1 or 2
1 or 2
2
8
10
2
12
2
15
2
4
Number of Blowers
2
2
Number of Power Supplies
Number of I/O Channels (SCSI Only)
SCSI SE/LVD Supported
Fibre Channel Supported
Hot-Swap Canisters
1
1
2
2
2
2
1 or 2
1
1
2
2
2
2
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
Removable Power Supplies
Removable Blowers
Fibre only
Fibre Only
Fibre only
P
P
P
N+1 Power Supplies
P
N+1 Blowers
P
MIA Support (FC Only)
P
P
P
P
Loop Expansion Support (FC Only)
Daisy Chainable (SCSI Only)
Built-in Termination (SCSI Only)
Auto Termination (SCSI Only)
SAF-TE/SES Ready (Optional)
SAF-TE/SES Compatible
SCSI to SCSI RAID Support
Fibre to SCSI RAID Support
Fibre to Fibre RAID Support
Fibre to ATA RAID Support
SCSI to ATA RAID Support
(D)esktop/(T)ower/(R)ackmount
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
Fibre only
Fibre only
P
P
P
P
P
P
R
D
D
DTR
T
TR
TR
R
* 6/10/15-bay unit features apply to both Tower and Rackmount models
1 Features are based on a standard configuration with no internal host controller(s) installed
2 Fibre channel 10/15-bay enclosures have built-in SES
3 Fibre Channel 2Gb Model available. 2Gb models use SFP transceivers.
StorBladeTM SCSI JBOD Installation Guide Rev A
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
StorBladeTM
StorBladeTM products use advanced mid-plane technology developed by JMR,
that allows power supplies, drives, and all other enclosure components to
interface into a single board. This provides superior performance and easy
connectivity.
The host interface supports single-ended, Wide Ultra2 SCSI (LVD), and Ultra
160. Connections to a SCSI host can be made using a 68-pin (HD68) SCSI cable.
4-bay Rackmount Specifications
Dimensions/Weight
Unit Weight
Height
Width
35 lbs. (15.9kg)
1-3/4" (1U) (44.45mm)
19" (483mm)
Depth
22" (558.8mm)
Power Supply
Quantity:
Power:
1
200 Watts
Input:
Output:
100-240 VAC; 50-60Hz
+3.3V @ 14A
+5V @ 20A
+12V @ 6A
Blower
Quantity:
Size:
Air Flow:
Noise:
2
70mm (2.75”) each
11.3CFM (0.32m3/min) each
38dB(A)
SCSI Features
Daisy Chaining
StorBladeTM SCSI enclosures include a SCSI I/O OUT port to allow additional
devices and enclosures to be daisy-chained easily onto the bus. The limit of
devices and enclosures that can be added is only regulated by the maximum cable
length and maximum number of devices as specified by the SCSI standard. For
specific connection and installation information, refer to Chapter 4.
ID Selection
0-15 device ID addresses are addressable in SCSI wide configurations and can be
easily set-up via ID Jumpers for each slot located on the I/O module. For specific
connection and installation information, refer to Chapter 4.
StorBladeTM SCSI JBOD Installation Guide Rev A
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Hardware Specification
This chapter covers specification information for the 4-bay StorBladeTM
enclosures. The following matrix describes the identification codes for the available
TM
configurations for all FORTRA and the StorBlade enclosures.
FR XX X L 2 1 X 2 X XX X X
SINGLE/DUAL CONTROLLER
S = Single Controller
D = Dual Controller
BACKPLANE TYPE
- = 1 Gigabit Backplane
2 = 2 Gigabit Backplane
CONTROLLER MANUFACTURER/MODEL#/INTERFACE
-
=
None (Blank if at the end of P/N)
H1 = Chaparral G5312/LVD Host/LVD Drives
H2 = Chaparral G7313/Fibre Host/LVD Drives
H3 = Chaparral K5312/LVD Host/LVD Drives
H4 = Chaparral K7313/Fibre Host/LVD Drives
H5 = Chaparral JSS122/LVD Host/LVD Drives
H6 = Chaparral JFS124/Fibre Host/LVD Drives
H8 = Chaparral JFS224/Fibre Host/LVD Drives
FZ = Microtest FileZerver Network Attached/Ethernet/LVD Drives
I2
=
Infortrend Sentinel 2500-50/LVD Host/LVD Drives
Infortrend Sentinel 2500-50 w/IFT9282F/Fibre Host/LVD Drives
Infortrend EonRAID 2500-50 w/IFT9288B6B/Fibre Host/LVD Drives
Infortrend EonRAID 5251F/2G Fibre Host/2G Fibre Drives
Infortrend SentinelRAID 150/LVD Host/LVD Drives
Infortrend EonRAID 7250-12U3D SCSI Host/ATA Drives
Infortrend EonRAID 7250-12F2D Fibre Host/ATA Drives
I3
I4
I5
IS
IF
=
=
=
=
=
M3 = Mylex DAC-FFx/1G Fibre Host/1G Fibre Drives
M5 = Mylex DAC-FFx2/2G Fibre Host/2G Fibre Drives
SAF-TE/SES
-
=
None (Blank if at the end of P/N)
S = SAF-TE/SES
POWER SUPPLY QUANTITY
# = A number Equal to Power Supplies in Enclosure
AC or DC POWER SUPPLY
-
D
=
=
AC Power Supply
DC Power Supply
COLOR - CANISTER/ACCENT
1 = Silver/Opal
2 = Black/Black
3 = Silver/Black
4 = Blue/Blue
DRIVE I/O SCSI CHANNELS or FIBRE LOOPS
# = A Number Equal to Drive I/O Channels
ENCLOSURE I/O
L = SCSI 3 Ultra 160 (LVD/SE Multimode, Fast-Wide, HD68)
F = 1 or 2Gb/s Fibre Channel
A = ATA
FIBRE GBIC READY
- = No GBIC Slots
G = GBIC Ready
u.s. Power cords Included
For International Models
NUMBER OF DRIVES
# = Drives (02,04,06,08,10,12,15)
Add Power Cord:
Australia = CBL-00602
Europe = CBL- 00525
FAMILY SERIES
FR = Fortra Rackmount
FT = Fortra Tower
UK
= CBL-00677
1U = StorBlade Rackmount
StorBladeTM SCSI JBOD Installation Guide Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
2-1
StorBladeTM
Environmental Specifications
Operating Temperature: 5°C to 40°C (41°F to 104°F)
Storage Temperature: 0°C to 65°C (32°F to 149°F)
Maximum ambient temperature is dependent on the recommended temperature to
meet the MTBF rating as specified by the manufacturer of the installed devices.
Electrical Specifications
AC Inlet Type: IEC320/EN60320
Power Cord: NEMA5-15P
Power Supply: Auto-switching for 110/220V operation
Agency Compliance
StorBladeTM enclosures have been designed and built to comply with the FCC
Class A, UL, CSA/TUV, CE, and C-Tick standards. For more information on
FCC Class A compliance, see page 2.
Packaging Specifications
StorBladeTM packaging has been designed to be reusable and recyclable.
Drives may be installed and shipped in the canisters as long as the canisters are in
their original packaging location and are not installed in the enclosure. Shipping
the unit with canisters and/or power supplies installed in the enclosure may cause
damage to the enclosure or to the drives and will void the warranty.
SAFETY TIP: Reshipping the enclosure with canisters, drives, or power
supplies installed in the enclosure may cause damage to these
components and will void the warranty
SICHERHEITSHINWEIS: Der Versand des Gehäuses mit eingebauten
Einschüben, Platten und Netzteilen kann zur Beschädigung dieser
Komponenten führen und somit den Garantieanspruch gefährden.
Packaging complies with ISTA (International Safe Transit Association) standards
and has been ISTA certified.
Each canister is pre-packaged in an anti-static bag. Do not throw the packaging
away if the product is intended for re-shipping. When transporting or shipping a
JMR approved shipping container must be used.
Disclaimer
The original product packaging has been tested and is safe under normal shipping
circumstances. Reshipping the product without using the original product
packaging will void the warranty. Do not ship the unit with canisters and/or
power supplies installed in the enclosure as this will void the warranty and could
cause damage to the unit and drives. The canisters should be packaged separately
within the product packaging, as provided.
StorBladeTM SCSI JBOD Installation Guide Rev A
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
StorBladeTM
Thermal Specifications
StorBladeTM enclosures have been designed to meet the air-flow/cooling
requirements for popular 7,200, 10,000 and 15,000 RPM disk drives. Using a
high performance blower, air is pulled in from all open vents and exhausted out
the back of the unit.
Rotation Vibration Specifications
StorBladeTM enclosures have been designed to meet the rotation
vibration/shock requirements for popular 7,200, 10,000 and 15,000 RPM disk
drives.
Fault Indication Features
This section reviews the indicators that will notify the user of a power supply or
blower that is in a fault state. More information is available in Chapter 5 power
supply and blowers.
Fault Indicators
All slots will blink 'Red' in color on a blower fault. On a power supply fault, the
front power supply LED will blink on and off.
Audible Alert
On a blower or power supply fault, an audible alert will sound.
StorBladeTM SCSI JBOD Installation Guide Rev A
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Device Installation
This chapter covers SCSI device installation for 4-bay 1U rackmount enclosures.
SCA Connection and Hot-Swapping
The unit uses SCA-2 type connectors which provide a safe means of
connection/disconnection when hot-swapping devices. In order to utilize this
feature, the host adapter or RAID controller and host operating software must
support the feature. Any SCA drive is capable of plugging directly into the
backplane of the unit and should not require any additional cabling or
connections.
Canister Removal/Insertion
1. Pull the handle out to unlock the canister from the StorBladeTM unit.
Notice that the locking tab slides down as the handle is pulled out.
2. Pull the canister straight out to remove. Ensure that any installed devices
are spun down before full removal to prevent damage to the drive.
Follow the steps in reverse to reinstall.
SAFETY TIP: After disengaging a device from the enclosure, allow 10 seconds
before pulling the canister out of the unit. This allows the device to
properly spin/shut down before transport.
Drive Installation
Front
Handle
Screws
Screws
1. After removing the canister, place it on a static free surface along with the
device to be installed.
StorBladeTM SCSI JBOD Installation Guide Rev A
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
StorBladeTM
2. Place the device in the canister with the four screw holes aligned with the
holes in the device. Mount the drive by using the screws included with the
unit. (use all 4 screws to mount the drive).
3. Replace the canister into the unit.
4. Repeat steps 1 through 3 until all devices are installed.
5. Configure ID, and other options as required
6. Establish host connection
StorBladeTM SCSI JBOD Installation Guide Rev A
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
4. SCSI Setup
This chapter covers SCSI device setup and option settings. Please take note of the
installation warnings below before beginning setup.
WARNING: Take care when connecting the unit to an AC power source to
ensure that it is plugged-in to a circuit of the appropriate rating (110v or
220v). For safe operation, the circuit should have over-current protection
to prevent damage to the unit in the event of circuit overloading.
WARNUNG: Vergewissern Sie sich, daß die Netzspannung (220V / 110V)
korrekt eingestellt ist, bevor Sie das Gerät mit dem Stromnetz verbinden.
Zur Sicherheit sollte das Netz über einen Überspannungsschutz zur
Vermeidung von Schäden im Falle einer Überlast verfügen.
WARNING: When connecting the unit to an AC outlet or power strip, ensure
that the outlet has the proper connection for grounding. The AC power
cables included with the unit have three prongs, one of which is used for
the ground connection. Do not use a two prong AC cable with the unit
since this will not allow for proper unit grounding and could cause
problems with normal unit operation.
WARNUNG: Bei der Verbindung der Unit mit einer Steckdose oder einer
Verteilerdose sollten sie auf eine korrekte Erdung derselben achten. Die
mitgelieferten Kaltgeräteanschlußkabel habe 3 Kontakte, von denen
einer zur Erdung verwendet wird. Verwenden Sie kein Stromkabel mit 2
Anschlüssen, da dieses keine korrekte Erdung ermöglicht und Probleme
während des regulären Betriebs verursachen kann.
Basic Personality Card Setup
This section covers 4-bay 1U SCSI JBOD units using the basic personality card.
This card does not have a controller interface built-in. The following Figure shows
the slot numbering sequence used to refer to device bays and additionally shows the
factory ID value for each slot. Slots 0-1 are on Channel A and Slots 2-3 are on
Channel B.
Slot 3, ID 3
Slot 1, ID 1
Slot 0, ID 0
Slot 2, ID 2
A
B
StorBladeTM SCSI JBOD Installation Guide Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
4-1
StorBladeTM
Setting ID
The basic personality card has jumpers available on the personality card to set the
ID for each slot. To access the jumpers the top cover must be removed. The
following picture indicates the location of jumpers W1-W4.
W2
W4
W3
W1
NOTE: View is from rear of the unit.
There are 4 jumpers on the personality card (W1, W2, W3, and W4) for hard
setting the ID of each slot.
Header W1 is for slot 3
Header W2 is for slot 2
Header W3 is for slot 1
Header W4 is for slot 0
Switch settings are shown from the rear of the unit.
Available ID's
Each bus is allowed to have ID's that range from 0-15. No two devices on the
same bus may share the same ID. Each host controller always uses one ID. The
Figure above shows all 0-15 possible ID settings.
StorBladeTM SCSI JBOD Installation Guide Rev A
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
StorBladeTM
ID Conflict
When two devices share the same SCSI ID, a conflict occurs. This conflict must
be corrected before the SCSI bus will work properly. If a conflict occurs, check
all jumper settings to ensure that no devices on the bus share the same ID. Also
check all other devices on the bus outside of the enclosure.
Front Status LEDs
A status indicator is located on each canister. A 'Blue' light indicates normal drive
activity. A 'Red' light indicates a device fault. If all canisters display a 'Red' light
that is blinking on and off it indicates that there is a system fault. A system fault
is either a power supply or blower failure. The power supply and blowers are not
field replaceable units. A fault with either the power supply or blowers will
Alarm
Reset
Button
Drive Status
Indicators
Power Fan FLT
Temp FLT
A blue light on a single canister
indicates device activity or busy.
A red light on a single canister indicates
a device fault.
External I/O Connection
The external I/O connections are located on the back of the unit. The figure below
shows the external I/O connections available.
SCSI A
OUT
SCSI A
IN
Power
Supply
Fan
SCSI B
IN
SCSI B
OUT
AC Inlet
StorBladeTM SCSI JBOD Installation Guide Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
4-3
StorBladeTM
The SCSI In ports are used to connect to a host and require an external cable with
a 68-pin High-Density male connector to mate at the enclosure side. Cables are
not included.
Each SCSI channel must use a separate external cable connection from the
rackmount to the host adapter or RAID controller. It is important that the external
cable length and impedance is taken into consideration and is adequate for the
devices and SCSI speeds being used.
JMR carries its own line of high quality external SCSI Cables.
Termination
Termination must be provided at the end and beginnings of each SCSI bus either
internally or externally. Drive level termination is not recommended since the
terminated device may be easily removed.
Termination is not automatic and the Channel A OUT and Channel B OUT
connections must have LVD/SE termination if not used.
Daisy-Chaining
SCSI I/O Out ports are used to add other enclosures and devices to the SCSI bus.
SCSI I/O Out ports require a cable with a 68-pin High-Density male connector to
mate. When daisy chaining, the SCSI I/O Out port of the enclosure is connected
to the SCSI I/O In port of the enclosure or device being added. Ensure that when
new devices are added to the SCSI bus, that the ID does not have a conflict. Once
the units are connected together, termination must be moved to the last device or
enclosure on the SCSI bus.
The devices or enclosures daisy-chained together must be compatible SCSI
devices. Single-ended interface devices cannot be on the same daisy-chained bus
with differential interface devices. Up to 16 devices (including the host) may be
daisy-chained together on the same bus.
SCSI Accessories
JMR carries its own line of external StorBladeTM compatible SCSI SE and LVD
terminators. The following Table lists JMR part numbers and descriptions. Please
contact a JMR representative for current availability and pricing.
JMR SCSI TERMINATORS
JMR Part #
Ends
Connector Type
Terminator Type
CNA-01883
Molded
SCSI-3 (68-pin)
SE/LVD Multimode
StorBladeTM SCSI JBOD Installation Guide Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4
StorBladeTM
JMR carries its own line of high-quality external StorBladeTM compatible SCSI
cables. The following Table lists JMR part numbers and descriptions. Please
contact a JMR representative for current availability and pricing.
JMR SCSI CABLES
JMR Part #
CBL-00532
CBL-00534
Ends
Connector Type
SCSI-3 to SCSI-3
SCSI-3 to SCSI-3
Length(FT)
Molded
Molded
3
6
StorBladeTM SCSI JBOD Installation Guide Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
4-5
5. Power Supply and Blowers
This section covers operation of the power supply and blowers.
Power Supply Removal/Insertion
In the 1U04 SCSI JBOD enclosure, the power supply is not a field replaceable
unit (FRU). Therefore, if you have a power supply malfunction, contact
Blower Removal/Insertion
In the 1U04 SCSI JBOD enclosure, there are two blowers that are not field
replaceable units. If a blower malfunction occurs, please contact JMR Electronics.
StorBladeTM SCSI JBOD Installation Guide Rev A
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
6. 1U04 Cabinet Installation
This chapter covers the installation of the Rackmount enclosure into a standard
19" (483mm) wide and 30" (762mm) to 36" (914mm) deep cabinet that meets the
EMA/RETMA standards.
Before beginning rail installation, please take note of the following precautions:
NOTE: When installing the unit into a cabinet or closed environment, the
operating ambient temperature of the rack environment may be greater
than the maximum recommended ambient temperature. Consideration
must be taken to meet the maximum recommended ambient temperature
(Tmra) for the best unit operation.
HINWEIS: Wenn das Gerät in einen Gehäuseschrank oder eine sonstige
geschlossene Umgebung verbaut wird, kann die Umgebungstemperatur
über die maximal zulässige Betriebstemperatur ansteigen. Maßnahmen
bzgl. der maximalen, empfohlenen Betriebstemperatur (Tmra) müssen
getroffen werden, um eine bestmögliche Funktion des Gerätes zu
gewährleisten.
WARNING: Ensure that the front and back of the unit are not blocked when
installing the unit into a cabinet or closed area. Blocking the front or
back of the unit can cause reduced air- flow that will compromise the
safe operating environment within the unit.
WARNUNG: Vergewissern Sie sich, daß das Gerät an Vorder- und Rückseite
nicht abgedeckt ist, wenn das Gerät in einem Gehäuseschrank oder
einer geschlossenen Umgebung verbaut wird. Abdeckung der Vorder-
und Rückseite kann verminderte Kühlung zur Folge haben und somit
sichere Betriebsbedingungen negativ beeinflussen.
WARNING: When loading the unit into a cabinet, ensure that a hazardous
condition is not achieved due to uneven mechanical loading. To prevent
injury, remove the power supplies and drives before loading, and re-
install them after the unit has been secured in the cabinet.
WARNUNG: Vermeiden Sie während des Einbaus des Gerätes in einen
Gehäuseschrank jegliche gefährliche Aktionen, selbst wenn diese nur
mechanischer Art sind. Um Verletzungen zu vermeiden, entfernen Sie
die Netzteile und Laufwerke vor der Montage und installieren Sie diese
erst erneut, wenn das Gerät im Gehäuseschrank gesichert
ist.Vergewissern Sie sich, daß das Gerät an Vorder- und Rückseite nicht
abgedeckt ist.
StorBladeTM SCSI JBOD Installation Guide Rev A
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
StorBladeTM
Rail Mounting Kit Hardware
•
•
Eight #10-32 Screws
Four each #8-32 Screws/Washers/Nuts
Spare Hardware Parts
Check with a JMR Sales Representative for pricing and availability of spare
hardware parts.
Description
#10-32 Screw
#8-32 Screw
#8-32 Nut
JMR Part Number
HDS-01580
HDS-00350
HDN-00040
#8-32 Washer
HDW-00080
Rail Installation
Expansion Rail
Main Rail
Rear
Front
1. Affix the extension brackets to the main rail using the #8-32
screw/washer/nut assemblies. Adjust to the correct length for the cabinet
depth being used.
Two #10-32 Screws at
each end
Front of
Rackmount
Unit
Two #8-32
Screws/Washers/Nuts
StorBladeTM SCSI JBOD Installation Guide Rev A
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
StorBladeTM
2. Affix the extension bracket to the rear of the unit using two #10-32
screws. There are 3 holes in the extension bracket for mounting.
Depending on the hole pattern that is being used in the cabinet, two holes
should always be available for securing the extension bracket.
3. The fronts of the rails have three holes. Two of the holes (top and bottom)
are used to secure the rail to the cabinet. The middle hole is used to
secure the enclosure to the rail and cabinet. Secure the front of each rail
to the cabinet vertical rails using two #10-32 screws for each rail.
4. Slide the unit into the cabinet and secure it to the cabinet by tightening
the two embedded thumb screws.
StorBladeTM SCSI JBOD Installation Guide Rev A
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Product Support
For current information on this product, including updates to the manual and
technical support related issues, please contact the sales support section of our
directly at the address below.
US Corporate Headquarters
JMR Electronics, Inc.
ATTN: Technical Support Division
20400 Plummer St.
Chatsworth, CA 91311
Customer Support: (818) 739-1140
E-mail: [email protected]
Office Hours: Monday-Friday 8:00 A.M. to 5:00 P.M., Pacific Standard Time
Internet: http://www.jmr.com
Manual Changes
Revision A - Initial Release
StorBladeTM SCSI JBOD Installation Guide Rev A
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Drive and Controller
Manufacturers
Drive Manufacturers
Fujitsu
Internet Address: www.fcpa.com
Hitachi
Internet Address: www.hitachi.com
IBM (International Business Machines Corporation)
Internet Address: www.ibm.com
Maxtor
Internet Address: www.maxtor.com
Seagate Technology
Internet Address: www.seagate.com
RAID Controller Manufacturers
Adaptec, Inc.
Internet Address: www.adaptec.com
Chaparral Network Storage
Internet Address: www.chaparralnet.com
Digi-Data Corporation
Internet Address: www.digidata.com
Infortrend Corporation
Internet Address: www.infortrend.com
Intel ICP VORTEX (Intelligent Computer Peripherals)
Internet Address: www.icp-vortex.com
Mylex Corporation
Internet Address: www.mylex.com
Silicon Image, CMD Storage Systems
Internet Address: www.cmd.com
StorBladeTM SCSI JBOD Installation Guide Rev A
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
StorBladeTM
Host Bus Adapter Manufacturers
Adaptec, Inc.
Internet Address: www.adaptec.com
Antares Microsystems
Internet Address: www.antares.com
Emulex Corporation
Internet Address: www.emulex.com
JNI Corporation
Internet Address: www.jni.com
QLogic Corp.
Internet Address: www.qlogic.com
StorBladeTM SCSI JBOD Installation Guide Rev A
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
|