SB-T-CAM/12W3V3 INSTR_SKU# 011284
InstallatIon
d I F F I C u lt Y :
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
out
oF
I n s t a l l a t I o n G u I d e
for the
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
35
SB-T-CAM/12W3v3
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
estImated tIme:
2-3 HouRs
sKu#94437
2000
s t e P
1
Remove any contents from the trunk so that you have a
clean area to work in.
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
s t e P
2
Remove both of the hardboard floor inserts
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. If you prefer to perform your own installation,
please read this installation guide completely
before beginning the process.
s t e P
3
The Jack and it’s mounting foam will be removed from the
compartment on the passengers side of the trunk floor.
Continued on Next Page
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-T-CAM/12W3V3 INSTR_SKU# 011284
s t e P 1 2
S T E P 1 6
Attach the upper mounting bracket into the just installed
1/4-20 Rivet Nut using One of the supplied 1/4-20 Phillips
Head Screws. The correct order of the hardware is indicated
in the illustration below.
Test the Stealthbox® to ensure proper operation then,
remount using the supplied three Phillips Head Screws, Split
Lock Washers and, Flat Washers.
s t e P 1 3
S T E P 1 7
The two lower brackets from the Stealthbox® should be con-
figured as shown, the one that goes up will be the same, just
arranged vertically.
LOCK WASHER
FLAT WASHER
C o n G R a t u l a t I o n s !
You have completed the installation for this model!
Enjoy your new Stealthbox®!
THREADED INSERT
STEALTHBOX®
MOUNTING BRACKET
LOCK WASHER
HEX BOLT
VEHICLE BODY
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
RIVET NUT
PHILLIPS HEAD SCREW
s t e P 1 4
Press in at the bottom of the enclosure so that it sits as tight
in the side as possible, and mark the locations for the bottom
anchors to be drilled through the floor. Remove the enclo-
sure from the side.
s t e P 1 5
Using a drill with a 3/8” bit, drill through the locations marked
in steP 14 . Repeat steP 10 in both holes.
*CAUTION*
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
transmission lines, electrical wiring, exhaust systems
or anything else that might cause a reduction in
your weekly pay. always wear eye protection when
drilling.
Page 3 • JL Audio, Inc 2008
Continued on Next Page
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-T-CAM/12W3V3 INSTR_SKU# 011284
I n C l u d e d H a R d W a R e
3) 1/4-20 Rivet Nut
3) 1/4” Split Lock Washer
3) 1/4-20 x 1” Hex Head Bolt
6) 1/4” Flat Washer
3) 1/4-20 x 5/8” Pan Head Phillips Screw
s P e C I F I C a t I o n s
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 12W3v3-4
Nominal Impedance: 4 Ohms
Continuous Power Handling: 500 Watts
P o W e R R e C o m m e n d a t I o n
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1v2.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1v2
when being used to power your Stealthbox®.
The JL Audio 250/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
m I d / H I G H F R e q u e n C Y d R I v e R F I t m e n t
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6” x 9”- Front Doors
Fits JL Audio Models: TR690-TXi, C2-690tx, VR690-CXi
Rear Speaker Size / Location: 6” x 9”- Rear Door
Fits JL Audio Models: TR690-TXi, C2-690tx, VR690-CXi
(954) 443-1100
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve”and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011284 ©12-10-2008
•
Printed in USA
•
©2008 JL Audio, Inc.
•
U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902
#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign
1
0
3
6
9
N
O
R
T
H
C
O
M
M
E
R
C
E
P
A
R
K
W
A
Y
•
M
I
R
A
M
A
R
,
F
L
O
R
I
D
A
•
3
3
0
2
5
•
U
S
A
Page 5• JL Audio, Inc 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
|