SB-P-CYNNE//10W6v2/BK__INSTR__SSKKUU##00111231
INSTALLATION
D I F F I C U LT Y :
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
OUT
OF
I N S T A L L A T I O N G U I D E
for the
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
35
S B -P -C Y N N E /1 0 W 6 v 2 /B K
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
ESTIMATED TIME:
2003 - 22006 Porsche Cayyenne
2-3 HOURS
S T E P
1
Remove any contents from the cargo area.
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
S T E P
Remove the flooring.
2
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 1 year if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
S T E P
3
With a T-30 wrench or socket, remove the pair of hold down
cleats(A).
A
A
With an 10mm socket, remove the bolt(B) that secures the
side panel to the vehicle.
B
Continued on Next Page
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-P-CYNNE//10W6v2/BK__INSTR__SSKKUU##00111231
S T E P 1 2
Remove the plastic collar that is around the hinge pin.
S T E P 1 6
Pull the SRS plastic badge from the upper c-pillar trim.
With a T-25 socket, remove the bolt that has been
exposed.
S T E P 1 3
Remove the trim panel.
S T E P 1 7
An airbag is located behind the c-pillar trim. Use caution
while removing this panel. All wiring/connections should be
protected.
As in the illustration, reach around to the rear of the c-pillar
trim and carefully remove the c-pillar trim from the c-pillar,
by pulling towards you.
S T E P 1 4
With a 17mm socket and ratchet, remove the seat belt
retracting unit.
S T E P 1 8
With a T-25 socket remove the bolt that secures the front
of the side trim panel to the c-pillar.
S T E P 1 5
S T E P 1 9
Remove the plastic ring from the rear seat’s upper latch pin.
From the driver’s side rear door opening. Pull the front of the
cargo side trim panel from the vehicle’s body. Do not fully
remove this side trim panel at this time.
Page 3 • JL Audio, Inc 2007
Continued on Next Page
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-P-CYNNE//10W6v2/BK__INSTR__SSKKUU##00111231
S T E P 2 4
Found in the rearmost driver’s side floor corner, remove
the rubber grommet in the cargo area.
S T E P 2 0
With a T-25 socket, remove three bolts that secures this
rear side trim panel.
Unsecure the wire harness from the wheel well.
*Make sure the ignition is not turned on*
Loosen the bolt that secures the brown wires to the
flooring of the vehicle.
Once loose, turn this wire assembly counter clockwise until
the wires are routed as illustrated in the picture. Secure the
bolt.
S T E P 2 1
Pull the rest of the side trim panel from the body of the
vehicle.
S T E P 2 5
Place the supplied top mount plate into position. The plate
will only fit one way. The hole in the mounting plate will line
up with the access hole from the removed grommet.
Once the side trim panel is loose, disconnect the power
outlet 12V plug from the wire harness.
S T E P 2 2
Pull the side trim panel out of vehicle.
S T E P 2 6
Run speaker wire from the amplifier’s location to the
Stealthbox® location and check for proper operation of
the woofer.
S T E P 2 3
S T E P 2 7
With a T-30 socket, remove the bolts that secure the pocket
to the body of the vehicle.
Thread in one of the supplied socket cup set screws into the
bottom of the Stealthbox®, leaving 1-inch exposed.
Page 4 • JL Audio, Inc 2007
Continued on Next Page
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-P-CYNNE//10W6v2/BK__INSTR__SSKKUU##00111231
S T E P 2 8
S T E P 3 2
Fully thread the supplied coupler to the first socket cup set
With a 9/16-inch socket and the remaining supplied pair of
screw from STEP 27.
bolt assemblies, secure the L-bracket to the Stealthbox®.
Thread the second supplied socket cup set screw into the
coupler.
S T E P 2 9
S T E P 3 3
Place the Stealthbox® into position by guiding the socket
cup set screw assembly through the hole in the top
mounting plate installed in STEP 25.
From under the vehicle, place the supplied mounting plate,
flat washers, lock washers and then hex nut onto the
protruding socket cup set screw. Using an 9/16-inch socket,
secure this bottom mounting assembly.
THREADED INSERT
STEALTHBOX WALL
SOCKET CUP SET SCREW
COUPLER
TOP MOUNTING PLATE
The bottom of the Stealthbox® will not touch the mounting
plate. The coupler will be touching the mounting plate.
Note: For added protection, it is recommended that
you apply a bead of silicone between the vehicle and
the mounting plate. After the bolt assembly is tightly
secured, it is also recommended that vehicle under-
coating material is applied to the exposed assembly.
VEHICLE SHEET METAL
BOTTOM MOUNTING PLATE
LOCK WASHER
FLAT WASHER
SOCKET CUP SET SCREW
HEX BOLT
S T E P 3 0
S T E P 3 4
Once the Stealthbox® is in position, place the supplied piece
of black carpeting between the Stealthbox® and the rear side
of the wheel well. You need to cover the corner of the wheel
well just in front of the Stealthbox®.
Place the factory side trim panel, removed in STEP 22, back
into place.
S T E P 3 1
S T E P 3 5
Reconnect the power outlet 12V plug to the wire harness,
unplugged in STEP 22.
Place a supplied 3/8-inch lock washer and then a supplied
flat washer onto the supplied 3/8-inch bolts.
Place two of these mounting bolt assemblies through the
supplied L-bracket. The L-bracket can only be posistioned
one way. Line up the mounting holes of the L-bracket to the
threaded inserts of the Stealthbox®.
Place the L-bracket into the mounting position and guide the
bolt assemblies through the two holes in the metal lip, as
seen in the picture to the left.
Place a supplied flat washer and supplied hex nut onto each
protruding bolt, behind the metal lip.
With an 9/16-inch box end wrench holding the nuts, use a
9/16-inch socket to secure the L-bracket to the metal lip.
Page 5 • JL Audio, Inc 2007
Continued on Next Page
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-P-CYNNE//10W6v2/BK__INSTR__SSKKUU##00111231
S T E P 3 6
S T E P 4 0
With a T-25 socket, secure the top c-pillar trim to the
c-pillar, from STEPS 16 & 17.
With a T-25 socket, secure the rear of the side trim panel
to the d-pillar, from STEP 20.
S T E P 3 7
S T E P 4 1
With a T-25 socket, secure the front of the side trim panel
to the c-pillar, from STEP 18.
Secure the upper d-pillar trim to the d-pillar, secure the trim
with the mounting screw that was removed and repalce the
plastic cover, from STEPS 7 & 8.
S T E P 3 8
S T E P 4 2
Replace the top sill plate, from STEP 6.
With a 17mm socket, secure the seat belt retracting unit,
from STEP 14.
S T E P 3 9
S T E P 4 3
Replace the lower d-pillar trim, from STEP 5.
Replace the trim and the plastic collar that goes around the
hinge pin, from STEP 12 & 13.
Page 6 • JL Audio, Inc 2007
Continued on Next Page
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-P-CYNNE//10W6v2/BK__INSTR__SSKKUU##00111231
S T E P 4 4
Replace the cargo door sill plate, from STEP 4.
I N C L U D E D H A R D W A R E
(2) 3/8-inchh --16 x 2 1//44--inchh Sockkett CCupp Seett Sccrrewwss
(1) 3/8-inch --16 Soockett CCupp Sett Scrrew Couupplleerr
(1) Alluummiinnuumm Topp Mountiinngg PPllaattee
(7) 3/88--iinncchh FFllaatt WWaasshheerr
(5) 3/8-inchh Lock Washheer
(4) 3/8-incchh -16 x 1 1/44--inch Heex Bolts
(3) 3/8-inchh --16 Hex Nuts
(1) Allumminnum Bottoom Mounntiinngg PPllaattee
S P E C I F I C A T I O N S
Enclosure Type: Acoustic SSuussppeennssiioonn ((sseeaalleedd))
Driver Type: 10WW6v2-D4
Nominal Impedance: 2 ohms mono
Continuous Power Handling: 4000 Watts
S T E P 4 5
A
P O W E R R E C O M M E N D A T I O N
With a T-30 wrench or socket, mount the pair of hold down
cleats(A), from STEP 3.
JL Audio recommends using a high quality amplifier such as the JL Audio 500/1.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 500/1 when
being used to power your Stealthbox®.
With a 9mm socket, mount the bolt(B) that secures the side
panel to the vehicle, from STEP 3.
A
P
r
e
e
a
m
p
F
O
u
t
p
u
t
S
e
c
t
io
e
n
In f r
a
s
o
n
ic
F
ilt
e
r
"Q
"
C
e
5
n
t
e
r
F
r
5
e
5
q
0
.
B
o
o
s
t
(d
B
3
)
A
m
p
o
L P
F
ilt
e
e
r
A
t
m
p
lif ie
r
In
p
u
t
S
.
e
c
t
io
n
S
S
u
b
w
o
o
f e
r
O
u
t
p
u
t
F
ilt
e
r
S
lo
p
O
u
t
p
u
t
M
o
d
M
d
1
e
/
S
lo
p
2
In
p
u
V
o
lt
a
g
e
In
p
u
t
S
e
n
s
S
ig
n
a
l
e
n
n
s
in
g
1
.
6
4
5
+1
0
1
.
.
1
2
4
.
.
7
3
3
5
+4
+1
B
0
.
7
2
7
F
u
ll
R
a
n
g
e
/
A
m
p
F
ilt
e
r
/
O
u
t
ilt
e
r
1
2
d
B
/
2
4
d
B
5
O
5
f
f
/
3
0
0
H
z
O
f
f
/
2
d
B
/
4
d
B
L
o
w
/
H
ig
h
O
f
f
/
O
0
5
2
0
8
5
0
+1
5
3
6
5
6
5
F
ilt
e
r
M
o
d
e
2
1
4
0
5
5
0
8
2
5
5
5
8
B
a
s
s
E
Q
+1
2
V
D
C
G
r
o
u
n
t
d
R
e
m
o
t
e
_
_
+
+
A
B
C
d
a
o
v
s
n
a
s
t
n
r
c
e
d
1
8
5
0
4
5
1
2
0
4
5
1
2
0
J
-c
L
h
A
n
U
D
l
IO
y s
5
e
0
0
m
/1
lif ie
o
l
M
O
N
O
O
U
T
P
U
T
O
N
LY
5
6
e
0
4
0
0
z
4
0
2
0
0
L
P
/
H
P
O
f
f
/
O
n
f iv
e
a
n
e
s
m
a
p
r
In
f
r
a
s
o
n
ic
F
r
q
.
(H
z
)
R
e
m
o
t
e
B
a
s
s
P
o
r
t
F
ilt
e
r
F
r
e
q
.
(H
)
L
e
f
t
C
h
.
R
ig
h
t
C
h
.
L
e
f
t
C
h
.
R
ig
h
t
C
h
.
F
ilt
e
r
F
r
e
q
.
(H
z
)
S T E P 4 6
Replace the rear seat removed in STEP 9 & 10.
The JL Audio 500/1 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6.5--inncchh // FFroont Doors
Fits JL Audio Models: TR650-CSi, TR650-CXXii,, VVRR665500--CCSSii,, VVRR665500--CCXXii,, XXRR665500--CCSSii,, XXRR665500--CCXXii,,
C5-6550, C5-6550x & ZR66550-CSi
Rear Speaker Size / Location: 6.5-inch / Reeaarr DDooors
Fits JL Audio Models: TR650-CXi, VRR650-CXi,, CC55--66550x && XXRR650-CXi
S T E P 4 7
Replace the flooring and any contents, from STEP 1 & 2.
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
w
w
w
. j l a u d i o . c o m
(9 5 4 ) 4 4 3 -1 1 0 0
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011231-04-23-2007
•
Printed in USA
•
©2007 JL Audio, Inc.
•
U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902
#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign
patents pending. For more detailed information please visit us online at www.jlaudio.com.
1
0
3
6
9
N
O
R
T
H
C
O
M
M
E
R
C
E
P
A
R
K
W
A
Y
•
M
I
R
A
M
A
R
,
F
L
O
R
I
D
A
•
3
3
0
2
5
•
U
S
A
Page 7 • JL Audio, Inc 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
|