®
Stealthbox
I N S T A L L A T I O N G U I D E
START
HERE
for the
SB-F-RTRKCTR/12W3v2
➔
➔
➔
Rear Console Only
(Fits 2002-Up Ford SuperCrew
Harley Davidson, King Ranch;
2001-2002 Lincoln Navigator and
2002 Blackwood )
STEP 1: Remove front exposed pocket,
internal instert and rubber flooring.
STEP 2: With an 8mm socket and long
extenstion, remove the four bolts. Located
where the front pocket was removed from in
STEP 1.
STEP 3: Remove the pair of bolts from side
rear of the OEM console.
You will have to lower the two rear seats and
lift up drop flooring to expose the bolts.
After the pair of bolts are removed, remove
OEM console out of truck.
This Stealthbox is a product
which requires professional
installation skills and tools.
Please read this installation guide
thoroughly before beginning the
project. It will guide you step by
step through the installation. Several
of the steps in this process may
require two people to accomplish.
It is absolutely vital that the
enclosure be properly mounted to
the vehicle according to these
instructions. Failure to mount the
enclosure properly presents two
problems: 1)The sub-bass
performance will suffer due to the
movement of the enclosure caused
by the force exerted by the
woofer(s) and 2) A loose enclosure
presents a serious safety hazard in
the event of a collision or sudden
deceleration.
➔
➔
➔
STEP 4: With the OEM console removed
you , unbolt the rear bracket.
STEP 5: The Stealthbox is shipped with two
brackets attacahed to it. Remove the rear
angle bracket from the Stealthbox.
STEP 6: The top picture shows how the front
bracket is installed when shipped.
Remove all mounting hardware and flip the
front bracket. Remount the flipped bracket
with the same hardware.
Mount this black angle bracket to where the
OEMbracket was removed.
Use the three bolts that was removed in
STEP4.
The bottom picture shows the bracket
properly mounted for install.
Please enjoy your JL Audio
Stealthbox responsibly.
➔
Continued on Page 2 ➔
SB-F-RTRKCTR/12W3v2-D2, JL AUDIO, Inc 2002
Page 1
Sheet SKU#011159 Revision 11/18/2003
Download from Www.Somanuals.com. All Manuals Search And Download.
Cont.
From
Page 2
➔
➔
➔
➔
STEP 16: Use masking tape to mark cutting
IMPORTANT!!!!
IMPORTANT!!!!
STEP 17: A) Line up small angle bracket to front
template.
middle of OEM inner(cut) console and mark hole.
A) Cut 1 1/2” under lip.Where there is no
B) Where there is a ledge/reinforcement cut
IMPORTANT!!!! Please read STEP 16 A and
B before cutting.
ledge/reinforcement
1 5/16” under the ledge/reinforcement.
Using a suitable saw to cut OEM inner
console.
➔
➔
➔
➔
STEP 17: B) Using an 1/8” drill bit, drill
marked hole.
STEP 20: With lid mounted, drill “7th” hole
using a 1/8” drill bit.
Don’t forget to bolt down lid strap with the
7th t-15Torx screw.
STEP 18: Place inner (cut) OEM console inside
outter OEM console / top of Stealthbox.
STEP 17: C) Mount the small angle bracket using
the suppied black rivet and small washer.
Drill six holes using 1/8” drill bit. Using the OEM
inner console’s lid mounting holes as guides.
STEP 19: Using the six(out of seven)T-15Torx
bolts that was removed in STEP 10, mount lid.
➔
Continued on Page 4 ➔
SB-F-RTEKCTR/12W3v2-D2, JL AUDIO, Inc 2002
Page 3
Sheet SKU#011159 Revision 11/18/2003
Download from Www.Somanuals.com. All Manuals Search And Download.
Cont.
From
Page 3
CONGRATULATIONS!
INSTALL COMPLETE.
➔
➔
➔
➔
Included Hardware:
1) Black Pop Rivet
1) #4 Steel Flat Washer
1) Small Angle Bracket
1) #8x1/2” Pan Head Screw
2) 1/4” Flat Washers
2) 1/4” Lock Washers
2) #6 x 40mm Bolts
2) Round Steel Spacers
2)Tree Push-In Rivets
STEP 21: Mount lid strap using the
“7th” T-15Torx bolt.
STEP 22: With OEM outer console, OEM
inner cut console and hinged lid mounted.
Look in the lid latch catch, located on the
front of OEM inner console.You will see the
small angle bracket that was mounted in
STEP 11. Drill 1/8” hole through the lid latch
catch using the hole from the small angle
bracket as a guide. Mount the small angel
bracket with supplied #8x1/2” black pan head
screw to the Stealthbox.
STEP 23: Repalce front pocket that was removed
in STEP 1 and close the lid.
Mid/High Frequency Driver Information:
Specifications:
Enclosure Type: Acoustic Suspension (Sealed)
Driver Type: One JL AUDIO 12W3v2-D2 Subwoofer
Nominal Impedance: 4Ω
Front Location Driver Size:
Cont. Power Handling: 300 Watts
XR570-CSi
5"x7” (1271mm x 177.8mm)
JLAudio recommends using a high quality amplifier such as the JLAudio 250/1. The diagram below shows the recommended
crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power the JL Audio Stealthbox®.
Applicable JL Audio Products:
TR570-CXi, XR570-CXi or CSi
Rear Location Driver Size:
5"x7” (1271mm x 177.8mm)
XR570-CXi
Applicable JL Audio Products:
TR570-CXi, XR570-CXi or CSi
The JL Audio 250/1 is a very versitile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.
10369 N. Commerce Pkwy, Miramar, Florida 33025-392
Phone: 954.443.1100
Fax: 954.443.1111
SB-F-RTRKCTR/12W3v2-D2, JL AUDIO, Inc 2002
Page 4
Sheet SKU#011159 Revision 11/18/2003
Download from Www.Somanuals.com. All Manuals Search And Download.
|