®
Stealthbox
I N S TALLATI O N GUI DE
START
HERE
for the
SB-T-TUNCNSL2/10W3v2
(‘03-Up Toyota Tundra Access & Double Cab
with front bucket seats and center console)
➔
➔
➔
➔
➔
STEP 1: Using a 14mm socket, remove the
four bolts that secure the passenger side front
seat.
STEP 2: Tilt the seat to the rear, unplug the
exposed wire assembly, remove the seat from
the truck.
STEP 3: Remove the front storage access
door. Using a 10mm socket, remove the
exposed bolts.
This Stealthbox is a product which
requires professional installation skills and
tools.
Please read this installation guide thor-
oughly before beginning the project. It
will guide you step by step through the
installation. Several of the steps in this
process may require two people to
accomplish.
➔
➔
It is absolutely vital that the enclosure
be properly mounted to the vehicle
according to these instructions. Failure
to mount the enclosure properly pres-
ents two problems: 1) The sub-bass
performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and
2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.
STEP 4: With the main storage door open,
grab ahold of the black cup holder section
and pull up.
STEP 5: Using a 10mm socket, remove the
exposed bolts. Also remove the bolts that are
located at the bottom of the main storage
bucket.
STEP 6: Remove the plastic buttons that are
located on each side of the center console.
Please enjoy your JL Audio Stealthbox
responsibly.
Continued on Next Page ➔
SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005
Page 1
Sheet SKU#011180 Revision 4/6/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Cont.
From
Previous
Page
➔
➔
STEP 15: Place the Stealthbox into position, Press
down firmly.
STEP 14: Thread in the three supplied socket cup
set screws into the Stealthbox. Make sure that the
socket ends are on the outside of the Stealthbox.
The rear(left side of pic) threaded rods need to
protrude about 1 1/4” out of the Stealthbox.The
front socket cup set screw needs to protrude about
3/4”.
Place the Stealthbox into location. Slide the rear
socket cup set screw through the drilled out holes
from STEP10. Press firmly on the front of the
Stealthbox, marking the wax square.
➔
STEP 16(b): *Tundra Double Cab O nly*
STEP 16(a): *Tundra Access Cab O nly*
Remove the Stealthbox.You should have an impres-
sion on the wax square.
Remove the Stealthbox.You should have an impres-
sion on the wax square.
*CAUTIO N*
*CAUTIO N*
Before drilling, make sure that you are not going to
be drilling into any gas lines, brake lines, transmission
lines, electrical wiring, transfer case(4x4 vehicles) or
anything else that might cause a reduction in your
weekly pay. Always wear eye protection when drilling.
Before drilling, make sure that you are not going to
be drilling into any gas lines, brake lines, transmission
lines, electrical wiring, transfer case(4x4 vehicles) or
anything else that might cause a reduction in your
weekly pay. Always wear eye protection when drilling.
With the use of a 1/2” drill bit and drill. Drill out the
floor at the impression on the wax square
With the use of a 1/2” drill bit and drill. Drill out the
floor at the impression on the wax square
Continued on Next Page ➔
SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005
Page 3
Sheet SKU#011180 Revision 4/6/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Cont.
From
Previous
Page
➔
➔
➔
➔
STEP 17: Remove the wax square and run speak-
er wire.
STEP 18:
*Access Cabs O nly*
STEP 19: With the Stealthbox and the modified
A/C ducts in position. Place the front section of the
center console back into the proper location. Do
not secure at this time.
STEP 20: Place the Stealthbox into the center
console, outside of vehicle .
Replace the modified A/C ducts from STEP 10,
back into the vehicle.
*Double Cabs O nly*
(Stealthbox is only shown in the picture for position
purposes.You do not have to have the Stealthbox in
location to accomplish this step)
The permanent removal of the rear seat 12v plug is
neded.
*Remember to plug in the 12v sockets.*
(Stealthbox is only shown in the picture for position
purposes.You do not have to have the Stealthbox in
location to accomplish this step)
THREADED INSERT
STEALTHBOX WALL
➔
➔
VEHICLE SHEET METAL
FENDER WASHER
SOCKET CUP SET SCREW
FLAT WASHER
LOCK WASHER
HEX NUT
STEP 21: Place the Stealthbox/center console into
vehicle. Attach the speaker wire to terminal.
STEP 22: Place Stealthbox/center console upright
and into the proper position. Carefully guiding the
threaded rods through the three drilled holes.
STEP 23: Apply a supplied flat washer, lock wash-
er and nut onto the three socket sup set screw.
Tightly secure all three nuts. .
Back out the three socket cup screws to 1-1/4:”.
Pop in the four supplied black plastic push rivets,
into the screw holes on each side of the center con-
sole.
Continued on Next Page ➔
SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005
Page 4
Sheet SKU#011180 Revision 4/6/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Cont.
From
Previous
Page
CO NGRATULATIO NS!
INSTALL CO MPLETE.
➔
➔
➔
Included Hardware:
3) Wax Squares
3) 3/8”- 1-1/4” Fender Washer
3) 3/8” Flat Washer
3) 3/8” Split Lock Washer
3) 3/8”-16x2-1/4” Socket Cup Set Screw
3) 3/8”-16 Hex Nut
STEP 24: With the Stealthbox securely mounted
to the vehicle. Secure the plastic console to the
floor, using the factory screws from STEP 5.
STEP 25: Secure the front section of console with
the factory screws, from STEP 3.
Once both portions of the center console have
been secured. Snap in the cup holders from
STEP 4, front console storage door from STEP 3
and the plastic buttons from STEP 6.
Difficulty O f Installation:
Mid/High Frequency Driver Information:
Specifications:
Enclosure Type: Sealed
Front Location Driver Size:
6.5”
Driver Type: 10W3v2-D2
Nominal Impedance: 4Ω
Cont. Power Handling: 300Watts
Applicable JL Audio Products:
VR650-CSi
TR,VR, XR, ZR 650-CSi
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended
crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.
mounting plates are needed
+12VDC
Ground Remote
Preamp Output Section
Output Mode
Bass Control
Infrasonic Filter
Amp LP Filter
Mode/Slope
Amplifier Input Section
Input Voltage
Input Sens. Signal Sensing
Rear Location Driver Size:
6.5”
Full-Range/Low-Pass/High-Pass
Off/30Hz
+7
Off/12dB/24dB
Low/High
Off/On
+3
+1
+10
+13
Applicable JL Audio Products:
TR,VR,XR 650-CXi
JL AUDIO 250/1
monoblock subwoofer amplifier
Left Ch.
Right Ch.
LF Boost (dB) Filter Freq. (Hz)
Left Ch.
Right Ch.
mounting plates are needed
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.
VR650-CXi
10369 N. Commerce Pkwy, Miramar, Florida 33025-392
Phone: 954.443.1100
Fax: 954.443.1111
SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005
Page 5
Sheet SKU#011180 Revision 4/6/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
|