SYNTHESIS
S5160
POWER
AMPLIFIER
USER’S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1.0
1.1
2.0
2.1
3.0
4.0
4.1
4.2
4.3
5.0
6.0
7.0
Precautions _______________________________________________________4
Important Safeguards for Audio Products ________________________________4
Introduction and Features ____________________________________________6
Included __________________________________________________________7
S5160 Operation and Controls _________________________________________8
Connecting Your JBL Synthesis System_________________________________11
JBL Synthesis One: Suggested Rack-Mounting Order ______________________11
JBL Synthesis One: Control Wiring Diagram _____________________________12
JBL Synthesis One: Interconnection Diagram ____________________________13
Physical Considerations _____________________________________________14
Troubleshooting ___________________________________________________15
Specifications _____________________________________________________16
JBL Synthesis S5160 Power Amplifier User’s Manual
©2005 Harman International Industries, Incorporated. All rights reserved.
JBL and JBL Synthesis are registered trademarks of Harman International Industries, Incorporated.
THX and THX Ultra are trademarks of THX Ltd., which may be registered in some jurisdictions. All rights reserved.
®
JBL Consumer Products
8500 Balboa Boulevard, Northridge, CA 91329
250 Crossways Park Drive, Woodbury, NY 11797
516.255.4JBL
Part Number: S5160/120OM
A Harman International Company
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
1.0
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
1.1 Important Safeguards
For Audio Products
PLEASE READ CAREFULLY ALL THE
FOLLOWING IMPORTANT SAFEGUARDS
THAT ARE APPLICABLE TO YOUR EQUIPMENT
10. Protect the power cord from being walked on or
pinched, particularly at plugs, convenience receptacles and
the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod,
bracket or table specified by the manufacturer
or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been dam-
aged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
15. Do not use attachments not recommended by the
product manufacturer, as they may cause hazards.
16. This product should be operated only from the type
of power source indicated on the marking label. If you are
not sure of the type of power supply to your home, consult
your product dealer or local power company. For products
intended to operate from battery power, or other sources,
refer to the operating instructions.
17. If an outside antenna or cable system is connected
to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides informa-
tion with regard to proper grounding of the mast and sup-
porting structure, grounding of the lead-in wire to an anten-
na discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding elec-
trodes, and requirements for the grounding electrode.
See Figure A.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accor-
dance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves or other apparatus (including ampli-
fiers) that produce heat.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
1.0
24. Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in proper operat-
ing condition.
18. An outside antenna system should not be located in
the vicinity of overhead power lines or other electric light
or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits, as contact with them might be fatal.
19. Do not overload wall outlets, extension cords, or inte-
gral convenience receptacles, as this can result in a risk
of fire or electric shock.
23. When replacement parts are required, be sure the
service technician has used replacement parts specified by
the manufacturer or that have the same characteristics as
the original part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
20. Never push objects of any kind into this product
through openings, as they may touch dangerous voltage
points or short-out parts that could result in a fire or elec-
tric shock. Never spill liquid of any kind on the product.
21. The apparatus shall not be exposed to dripping or
splashing, and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
22. Do not attempt to service this product yourself, as
opening or removing covers may expose you to danger-
ous voltage or other hazards. Refer all servicing to qualified
service personnel.
25. The product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-22 of the NEC that pro-
vides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
Figure A.
Example of Antenna Grounding as per
National ElectricalCode ANSI/NFPA 70
Part No. HCGUL1492/6500 04/2004 EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
AND FEATURES
2.0
The S5160 provides a satisfying 160 watts per channel of
distortion-free audio (<0.03% THD) into 8 ohms. Because
of their power capabilities, all Synthesis amplifiers have an
extremely wide dynamic range, an element critical to realistic
home cinema. Sound levels equal to those at original per-
formances are easily re-created in even the largest of home
listening environments.
amplifiers may be used, in conjunction with two S800
subwoofer amplifiers, to power a complete 7.1-channel
home theater system. Alternatively, a single S5160 may
be used with one S800 subwoofer amplifier to power a
5.1-channel system.
Introduction
Congratulations on your purchase of this JBL Synthesis
S5160 power amplifier! You have chosen a product that
embodies the best of what JBL has discovered about the
emotional power of audio reproduction in more than fifty
years of preeminence in the field. This amplifier has been
designed and crafted to provide the user with a high level
of sonic performance; special attention has been paid to
minimize the number of components in the audio signal
path, resulting in extremely low distortion, excellent tran-
sient response and wide dynamic range. Synthesis prod-
ucts set new benchmarks in audio technology, and, when
used as part of a complete JBL Synthesis system, will
bring the ambience and acoustics of some of the world’s
greatest concert halls and theaters into your home.
High Power Capability
Auto Turn-On and Power Sequencing Circuitry
When used in a JBL Synthesis system, the S5160 can be
turned on automatically whenever the surround processor
is activated. No longer do you have to get out of that chair
to turn on the various pieces of equipment in your enter-
tainment system; just one touch on the remote control of
the surround processor, and you’re a few seconds away
from a truly impressive audio presentation!
To obtain the best performance from this amplifier, please be
sure to completely read this user’s manual and use the
S5160 only in accordance with its instructions.
Features
The JBL Synthesis S5160 power amplifier features the
following:
Modern amplifiers produce more power per channel (and
frequently have more channels) than those of the traditional
two-channel stereo era. Due to the high current demands
of power amplifiers at the instant of turn-on, the S5160,
S7150 and S800 amplifiers and the SDEC digital equaliz-
er are equipped with power sequencing circuits that turn
on each unit in sequence, avoiding the large instantaneous
current demand (and possible house circuit breaker trip-
ping) that would occur should they all turn on at the same
instant.
™
THX Ultra Specifications
This amplifier meets or exceeds the stringent specifications, includ-
ing those for power handling, total harmonic distortion, frequency
response, signal-to-noise ratio, slew rate, and crosstalk, set by the
THX Ltd. Audio division in their specifications for “Ultra”-class certifi-
cation. When incorporated into a complete THX® system, you will
hear in your home what the director and sound engineer heard in
the recording studio.
Full Five-Channel Operation
The S5160 has been designed to integrate well into the
world of multichannel audio. It is designed to reproduce
the front left and right, center and side channels, to pro-
duce a truly enveloping sound field. When coupled with
a high-quality subwoofer amplifier, such as the S800, it is
a solid foundation on which to build a high-performance
home cinema system that will astound the listener with its
power and realism. The S5160 is specially designed for
use with a Synthesis One system in which the front left,
right and center speakers are bi-amplified for smoother
and more accurate reproduction of every nuance of a
movie soundtrack or musical selection. Two S5160
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
AND FEATURES
2.0
One (1) detachable power cord
One (1) 6-foot 5-pin DIN trigger cable (M/M)
Two (2) 5-pin DIN/2-pin bare wire adapters
Two (2) 2-pin bare wire plugs
Quiet Cooling
2.1 Included
The S5160 utilizes a fan to cool the amplifier channels,
ensuring long-term reliability. To reduce fan noise to an
absolute minimum, a thermal sensing and control circuit
that senses increases in temperature within the amplifier
and powers a fan at a speed proportional to that tempera-
ture increase has been incorporated in the S5160. When
the S5160 is used at lower volume levels, the fan turns
very slowly – and quietly. At high listening levels (and the
higher operating temperatures this creates within any
amplifier), the sensing circuitry causes the fan to turn
faster, producing increased cooling. As a result, the fan
is never turning faster than necessary, and most of the
noise that is generated is masked by the program being
listened to.
Each S5160 amplifier includes the following items packed
in the carton. If any of these items is missing, please con-
tact your JBL Synthesis dealer or distributor, or visit our
Owner’s manual
Comprehensive and Isolated Circuit Protection
The S5160 amplifier employs sophisticated protection cir-
cuitry (one for each channel) that senses many possible fault
conditions, such as shorted loudspeaker wires or excess
power demand, and turns the affected channel(s) and their
blue front-panel indicators off until the fault condition is
removed, at which time normal operation is automatically
restored. While protection of this sort is not uncommon in
today’s well-designed amplifiers, a remarkable feature of
the S5160’s protection circuitry is that it is optically cou-
pled to the signal circuit; there is no direct electrical con-
nection between the signal path and the protection circuitry.
As a result, there can be no coloration of the
music, no interaction between protection and
amplification, until certain thresholds are
exceeded, at which point the channel(s) turn
off completely.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
S5160 OPERATION AND
CONTROLS
3.0
®
1. Power Switch
4. Input Jacks (Ch.1 Through Ch.5)
Pushing this button is all that is required to turn on the
S5160 if it is not part of a Synthesis system and the
Manual On/Auto On switch ¶ (rear panel) is in the
Manual On position. If the amplifier is used as part of a
JBL Synthesis system, and the Manual On/Auto On
switch ¶ is in the Auto On position, the amplifier will
turn on when the surround processor is activated. In this
application, the front-panel pushbutton Power switch
should be left in the ON (in) position. See the description
of the Manual On/Auto On switch ¶ for more infor-
mation on turning on the S5160.
The output signals from the Synthesis digital processor and
equalizer are connected to the input jacks in a Synthesis
One system. We suggest that the channels be assigned
as follows:
Amplifier #1:
Channel 1 Center Low-Frequency
Channel 2 Center High-Frequency
Channel 3 Right Front Low-Frequency
Channel 4 Right Front High-Frequency
Channel 5 Right Rear Surround
2. Standby Indicator
Amplifier #2:
This indicator, immediately above the front-panel Power
switch, will glow red when the amplifier is in the “standby”
mode, whether operating as part of a Synthesis system
or not. When the S5160 is in the “on” mode, this light will
shut off and the blue “on” mode indicators will light.
Channel 1 Right Side Surround
Channel 2 Left Side Surround
Channel 3 Left Front Low-Frequency
Channel 4 Left Front High-Frequency
Channel 5 Left Rear Surround
3. Power Indicators (Blue)
These indicators will light up when the power amplifier
is in the “on” mode. Each monitors the operation of one
channel, and will be extinguished if that channel’s
protection circuitry is activated.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
S5160 OPERATION AND
CONTROLS
3.0
ª
¢
•
¶
§
‚
∞
5. Speaker Terminals
6. External Fuses
Connect the speakers to these terminals, following the nor-
mal convention: Wire the “+” side of the speaker to the red
terminal, and the “–” side to the black terminal. Wire the
speakers with the proper polarity; reversing any speaker’s
connections will not damage either the speaker or the
amplifier, but will result in poor low-frequency performance
and imprecise imaging.
AC mains fuses are located on the back panel of the
amplifier. These fuses will not blow unless the amplifier is
asked to produce more power than its design allows for
a prolonged period or to prevent excessive current draw,
which could damage internal components during a fault
condition.
The amplifier has been designed to operate under virtually
all conditions. Even momentary short-circuiting of the
output (speaker) connections will not ordinarily damage
the output circuitry (although it will activate internal protec-
tion circuitry and cause one or more of the front-panel
LED indicators to be extinguished until the circuit resets
automatically).
WARNING: Terminals marked with the flash symbol
are hazardous when live. External wiring connected
to those terminals requires installation by trained
personnel, and the use of ready-made lead cords.
NOTE: The minimum load impedance that this amplifier
can handle safely is 8 ohms per channel. Using lower
impedance loads can damage the unit and will void
your warranty!
Fuse Replacement
To remove the fuse, turn off the Power switch and discon-
nect the power plug from the AC mains. Unscrew the fuse
holder cap and remove the fuse; install the new fuse and
secure the holder cap; and reconnect the AC mains. If
after replacing the fuse the unit is inoperative, service is
required; contact your JBL Synthesis dealer.
Wire-Run Length
Minimum Gauge
Up to 20'
Up to 50'
Up to 100'
16
14
12
WARNING: Always unplug the amplifier from
the AC mains before removing any fuse.
IMPORTANT: Never install a fuse that has a
higher rating than that specified on the back
panel of the amplifier or in the owner’s
manual.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
S5160 OPERATION AND
CONTROLS
3.0
The installer may find it preferable to use two-conductor
wire (18-gauge recommended) rather than long multi-
conductor DIN cables for the mode-switching connection
between the S5160 and these two speakers. Adaptors
supplied with the S5160 are used at the speaker end of
the wire to allow connection to the speakers’ DIN input
connectors. Proper polarity must be observed, as shown in
the wiring diagrams; reverse the connections at one end of
the wire if the speaker(s) do not switch modes – from
horn (Cinema) to tweeter (Music).
7. Manual On/Auto On Switch
9. Speaker Mode Control Connectors
Put this switch in the Auto On position if the amplifier is
being used as part of a JBL Synthesis system. When used
in this way, the S5160 will automatically turn on when the
Power switch is depressed and the surround processor is
activated. For other installations, or should individual control
of each component be desired, put this switch in the
Manual On position. The amplifier will then be controlled
solely by the front-panel switch.
The front left and front right speakers are switched
between Music and Cinema modes by signals present
at both the DIN connectors (as described in Section 8)
AND the two-conductor connectors shown at ª.
8. In/Out DIN Jacks
If you are using the amplifier as part of a JBL Synthesis
system, it is necessary to use these jacks to interconnect to
other system components so that control signals (Power
On/Off and Music/Cinema mode switching) can be trans-
mitted from one unit to the next, starting at the surround
processor, through the equalizer and amplifiers, and ending
at the speakers. Follow the connection diagrams on the
following pages for detailed information regarding these
connections. Make connections to these jacks only as
shown in the diagrams. If these jacks are used in any other
manner, e.g., to control electric screens, the unit can be
damaged and the warranty will be void. For specific electrical
information on these jacks, contact JBL Synthesis
Customer Service at 516.255.4JBL.
Note that five-conductor DIN cables MUST be used
between all other components to allow correct power and
mode switching, and that the same warning not to plug
anything into these jacks if you are not using the S5160
with a JBL Synthesis system applies here; do not attempt
to use these jacks to control anything other than the
mode-switching function of JBL Synthesis speakers, as
this may damage the S5160 and will void the warranty.
10. AC Inlet
Do not plug anything into these jacks if you
are not using the S5160 with a JBL Synthesis
system.
Your S5160 is shipped with an IEC-type removable power
cord that mates with the AC inlet on the rear panel. To
ensure proper operation, use the supplied power cord.
This amplifier is NOT a multivoltage unit; using a
power cord that is not compatible with a 120V, 60Hz AC
wall receptacle will void the warranty.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING YOUR
JBL SYNTHESIS SYSTEM
4.0
4.1 JBL SYNTHESIS ONE:
SUGGESTED RACK-MOUNTING
ORDER
General Information
A Synthesis One installation utilizing the benefits of bi-
amplification of the front speakers incorporates a total
of four power amplifiers; two S5160’s, and two S800’s.
Eight of the 10 channels on the S5160’s are to be used
for driving the high-frequency and low-frequency inputs on
the left, center and right speakers, as well as the two side
ambient speakers, as indicated in the chart on page 8.
Please also refer to the connection diagram on page 14.
Use the simplified connection diagrams on the following
pages to help you understand how to connect the S5160
amplifier to a JBL Synthesis system. These diagrams are
intended to show the signal flow through the system. For
more detail in making these connections, please refer to
the JBL Synthesis Certified Dealer Installation Manual.
Top
#1
SDP-40
Connect DIN and audio cables between system components, as
shown on the following pages. Make sure that on all power
amplifiers the Power switches are in the depressed (ON)
position and that the Manual On/Auto On switches ¶
are in the Auto On position. Operated in this mode, all of
the components will turn on with one touch of the Power
switch on the surround processor’s remote control.
#2
#3
SDEC-1000A
S800
#4
S5160
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING YOUR
4.2 JBL Synthesis One:
Control Wiring Diagram
JBL SYNTHESIS SYSTEM
4.0
INPUTS
COMPONENT VIDEO
PB
MAIN OUTPUTS
RECORD OUTPUTS
1
2
3
4
5
INPUT
PR
1
INPUT
PR
2
4
INPUT
PR
3
Y
PB
Y
Y
PB
1
(OSD)
2
1
2
INPUT
OUTPUT
SPEAKER CONTROL JACK
Y
PR
PB
Y
PR
PB
VIDEO
VIDEO
1
2
3
4
5
6
7
8
FRONT
CENTER SUBWOOFER
SIDE
REAR
Fix ZONE
L
2
Fix
Var
AUX
Var
(L)
(LS)
(RS)
(C)
L
L
L
L
L
(R)
(SUB)
R
R
R
R
R
R
1
2
LFE
MICROPHONE INPUTS
MAIN AUDIO OUTPUTS
AUDIO
TRIGGER OUTPUTS
AUDIO
S/PDIF
1
2
3
1
2
3
4
1
4
2
3
1
2
4
5
6
IR IN
5
6
RS 232
PIN 1 Ground
L
FRONT
R
CENTER
LFE
L
SUBWOOFER
R
L
SIDE
R
L
REAR
R
L
AUX
R
L
ZONE
2
R
PIN 2 +5vdc in Cinema mode
SDP-40
CONTROL JACK SIGNALS
SDEC-1000A
Digital Equalizer Controller
JBL Inc., Northridge CA
Made in USA
RS-232
DIN IN
DIN OUT
3
1
WARNING – To reduce the risk of
fire or electric shock, do not expose
this appliance to rain or moisture.
Do not remove cover. No user
serviceable parts inside. Refer
L/R IN
C/SUB IN
AMB IN
4
5
THX® CONNECTOR
OUTPUT
S/P DIF DIGITAL INPUT
ANALOG INPUT
CINEMA
MODE
AUTO
MODE
AUTO
ON
MANUAL
ON
2
servicing to qualified service personnel.
PIN 1 Ground
THX® IS
A
REGISTERED
TRADEMARK OF
LUCASFILM, LTD.
R-AMB
L-AMB
R-SUB
L-SUB
C-LO
C-HI
R-LO
L-LO
R-HI
L-HI
R-IN
L-IN
SUB-IN
C-IN
R-AMB-IN
L-AMB-IN
PIN 2 Ground
SDEC-1000A
CINEMA
MODE
AUTO
MODE
AUTO
ON
MANUAL
ON
PIN 3 +5vdc when Power is on
PIN 4 Not Used
PIN 5 +5vdc in Cinema mode
(Use “Cinema Mode” position only
when there are no music mode
speakers in the system.)
TO SPEAKERS
JBL SYNTHESIS
NORTHRIDGE, CA
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
IN
S5160 POWER AMPLIFIER
Ch.
1
Ch.
2
Ch.
3
Ch.
4
Ch.
5
Input
Input
Input
Input
Input
SPKR-1
SPKR-2
OUT
MANUAL
ON
AUTO
ON
ON
15A
120V
~
50/60Hz
1800W
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
ATTENTION:
TRIGGERS
OFF
IN
S800 POWER AMPLIFIER
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
ATTENTION:
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture
BRIDGED
Ch.
1
Ch.
2
VOIR LE CAHIER D'
INSTRUCTION
WARNING; To reduce the risk of fire or
electric shock, do not expose
BRIDGED
Input
Input
MONO
STEREO
this appliance to rain or moisture
+
+
+
+
+
-
-
-
-
-
serial number
Ch.
1
Output
Ch.
2
Output
Ch.
3
Output
Ch.
4
Output
Ch.
5
Output
OUT
No user serviceable parts inside. Refer
servicing to qualified personnel.
AUTO
ON
MANUAL
ON
S5160
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ON
10A
120V
~
50/60Hz
1200W
OFF
HAZARDOUS ENERGY MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
,
WARNING:
JBL SYNTHESIS
NORTHRIDGE, CA
BRIDGED
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
+
+
TRIGGERS
IN
-
S5160 POWER AMPLIFIER
Ch.
1
Ch.
2
Ch.
3
Ch.
4
Ch.
5
Input
Input
Input
Input
Input
+
-
-
serial number
Ch.
1
Output
Ch.
2
Output
SPKR-1
SPKR-2
OUT
Stereo/Mono
Manual
On
Auto
On
S800
MANUAL
ON
AUTO
ON
ON
15A
120V
~
50/60Hz
1800W
OFF
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
ATTENTION:
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture
VOIR LE CAHIER D'
INSTRUCTION
+
+
+
+
+
-
-
-
-
-
serial number
Ch.
1
Output
Ch.
2
Output
Ch.
3
Output
Ch.
4
Output
Ch.
5
Output
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
ATTENTION:
TRIGGERS
IN
S800 POWER AMPLIFIER
BRIDGED
Ch.
1
Ch.
2
WARNING; To reduce the risk of fire or
electric shock, do not expose
S5160
BRIDGED
Input
Input
MONO
STEREO
this appliance to rain or moisture
OUT
No user serviceable parts inside. Refer
servicing to qualified personnel.
AUTO
ON
MANUAL
ON
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ON
10A
120V
~
50/60Hz
1200W
NOTES
OFF
HAZARDOUS ENERGY MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
,
WARNING:
BRIDGED
+
+
-
1) To ensure proper operation, connect the system control
lines exactly as indicated.
+
-
-
serial number
Ch.
1
Output
Ch.
2
Output
Stereo/Mono
Manual
On
Auto
On
S800
2) If any of the control lines become disconnected while the
system is on, turn off all Synthesis components before
reconnecting control lines. This will reset all operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
CONNECTING YOUR
4.3 JBL Synthesis One:
Interconnection Diagram
JBL SYNTHESIS SYSTEM
4.0
Type
Length
Usage
INPUTS
COMPONENT VIDEO
PB
MAIN OUTPUTS
RECORD OUTPUTS
1
2
3
4
5
INPUT
PR
1
INPUT
PR
2
4
INPUT
PR
3
Y
PB
Y
Y
PB
2
1
2
1
(OSD)
INPUT
OUTPUT
Y
PR
PB
Y
PR
PB
SDEC1000A to
VIDEO
VIDEO
1
2
3
4
5
6
7
8
FRONT
CENTER
SIDE
Fix ZONE
L
Fix
Var
SUBWOOFER
REAR
2
Var
AUX
S5160, Rt angle RCA
attaches to Amp side
(L)
(LS)
(RS)
(C)
L
L
L
L
L
(R)
(SUB)
R
R
R
R
R
R
LFE
MICROPHONE INPUTS
AUDIO
MAIN AUDIO OUTPUTS
AUDIO
S/PDIF
TRIGGER OUTPUTS
1
2
3
1
2
3
4
1
4
2
3
1
2
Surround Processor to
S5160 rear ambient
channels for use in
7.1 systems Rt angle
RCA attaches to Amp
side
4
5
6
IR IN
5
6
RS 232
FRONT
CENTER
LFE
L
SUBWOOFER
R
ZONE
2
L
R
L
R
L
AUX
R
L
R
L
SIDE
R
REAR
SDP-40
SDEC-1000A
Optional 7.1
System Connection
For Left and Right
Rear Ambient Speakers
SDEC-1000
A
Digital Equalizer Controller
JBL, INC., Northridge CA
Made in USA
RS- 232
DIN IN
DIN OU
T
WARNING To reduce the risk of
–
fire or electric shock, do not expose
this appliance to rain or moisture.
Do not remove cover. No user
THX®CONNECTOR
OUTPUT
CINEMA
MODE
AUTO
MODE
AUTO
MAN AL
ON
U
serviceable parts inside. Refer
servicing to qualified serv ice personnel.
ON
ANALOG INPUT
T
HX® IS
TRADEMAR
LUCASF LM, LTD.
A
R
EGIS
T
ERED
OF
R- AMB
L- AMB
R- SUB
L- SUB
C- LO
C- HI
R- LO
L- LO
R- HI
L- HI
R- IN
L- IN
SUB- IN
C- IN
R- AMB- IN
L- AMB- IN
K
I
JBL SYNTHESIS
NORTHRIDGE, CA
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
IN
S5160 POWER AMPLIFIER
Ch.
1
Ch.
2
Ch.
3
Ch.
4
Ch.
5
Input
Input
Input
Input
Input
SPKR-1
SPKR-2
OUT
MANUAL
ON
AUTO
ON
ON
15A
120V
~
50/60Hz
1800W
OFF
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
ATTENTION:
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture
VOIR LE CAHIER D'
INSTRUCTION
+
+
+
+
+
-
-
-
-
-
serial number
Ch.
1
Output
Ch.
2
Output
Ch.
3
Output
Ch.
4
Output
Ch.
5
Output
Manual
On
Auto
On
S5160
JBL SYNTHESIS
NORTHRIDGE, CA
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
IN
S5160 POWER AMPLIFIER
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
ATTENTION:
TRIGGERS
IN
S800 POWER AMPLIFIER
Ch.
1
Ch.
2
Ch.
3
Ch.
4
Ch.
5
BRIDGED
Ch.
1
Input
Input
Input
Input
Input
Ch.
2
WARNING; To reduce the risk of fire or
electric shock, do not expose
BRIDGED
Input
Input
MONO
STEREO
this appliance to rain or moisture
SPKR-1
SPKR-2
OUT
OUT
MANUAL
ON
AUTO
ON
No user serviceable parts inside. Refer
servicing to qualified personnel.
AUTO
ON
MANUAL
ON
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ON
15A
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ON
120V
~
10A
50/60Hz
1800W
120V
~
50/60Hz
1200W
OFF
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
ATTENTION:
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture
OFF
HAZARDOUS ENERGY MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
,
WARNING:
serial number
BRIDGED
+
-
VOIR LE CAHIER D'
INSTRUCTION
+
+
+
+
+
-
-
-
-
-
serial number
Ch.
1
Output
Ch.
2
Output
Ch.
3
Output
Ch.
4
Output
Ch.
5
Output
+
+
-
-
Ch.
1
Output
Ch.
2
Output
Manual
On
Auto
On
S5160
Stereo/Mono
Manual
On
Auto
On
S800
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
ATTENTION:
TRIGGERS
IN
S800 POWER AMPLIFIER
BRIDGED
Ch.
1
Ch.
2
WARNING; To reduce the risk of fire or
electric shock, do not expose
BRIDGED
Input
Input
MONO
STEREO
this appliance to rain or moisture
OUT
No user serviceable parts inside. Refer
servicing to qualified personnel.
AUTO
ON
MANUAL
ON
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ON
10A
120V
~
50/60Hz
1200W
OFF
HAZARDOUS ENERGY MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
,
WARNING:
BRIDGED
+
-
+
+
-
-
serial number
Ch.
1
Output
Ch.
2
Output
S800
Stereo/Mono
Manual
On
Auto
On
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PHYSICAL
CONSIDERATIONS
5.0
Installation of the S5160 is a straightforward process.
IMPORTANT: The amplifier must be installed
following the directions described below. To
ensure adequate performance and safety, never
install the amplifier with less free space around the
amplifier than that specified.
IMPORTANT: For rack mounting, we recommend
using 10-32, 1"-long screws.
NOTE: Heavy equipment should not be supported
solely by the front mounting locations. It is recom-
mended that additional rear support be used.
1. The S5160 power amplifier has been designed to be
mounted in EIA standard racks or stacked freestanding
as long as there is 4 inches (10cm) of free space around
the amplifier (top, sides and rear). If the S5160 is being
mounted in a rack, it is suggested that its feet be removed
prior to installation. If the S5160 will be stacked with other
components, use the feet that came attached to the unit.
This will ensure that there is sufficient air space underneath
so that heat can be dissipated effectively.
2. Make sure that the amplifiers are located in a well-
ventilated, cool area. Be certain that the front and rear
panels are not obstructed, as the cooling fan brings air in
from the front and expels it at the rear. It is very important
not to obstruct the airflow from the center front panel;
heat buildup and premature failure may occur.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
6.0
Problem: Amplifier does not turn on. Neither the red nor blue indi-
cator lights are on.
Problem: Insufficient audio from the speakers.
Check that the output levels of the surround processor or
equalizer are set properly.
Make sure that the amplifier is plugged in, and verify that there is
the proper voltage (120V) at the wall outlet.
Problem: Insufficient bass.
Problem: The red indicator lights, but the blue indicators do not
light up when the Power switch is depressed.
Verify that the speakers have been wired to the amplifier with the
correct polarity.
1. If the amplifier is being used in a Synthesis system, make sure
that the surround processor is turned on, the Manual On/Auto
On switch is in the Auto On position, and that all of the neces-
sary DIN cables are connected between the various system
components. Refer to the “CONNECTING YOUR JBL
Problem: Front speakers do not switch from Music to Cinema
mode.
1. Make sure that the screw terminal and DIN adaptor cables to
speakers are correctly wired and are connected to the correct
jacks on the S5160.
SYNTHESIS SYSTEM” section for reference.
2. Make sure that all required DIN cables are connected between
2. If the amplifier is not being used with a Synthesis system, make
sure that the Manual On/Auto On switch is in the Manual On
position.
system components.
Problem: Audible hum from the speakers.
Problem: There is no sound from the speakers, but the amplifier
is on (blue indicators lit).
1. Check the power outlets and make sure that there is a solid
earth ground present. (The services of an electrician may be
required.)
1. Make sure that the surround processor or equalizer is on, and
that the correct source has been connected and selected.
2. Make sure that all signal cables are routed away from power
cords.
2. Make sure that the correct outputs are connected from the
surround processor or equalizer to the amplifier.
3. If these suggestions fail, experiment by running ground wires
between the rear-panel screws of the amplifiers and the other
system components, such as the surround processor or signal
processing package.
3. Make sure that the speakers are connected to the correct
terminals. Check for short circuits at both ends of the speaker
cables.
If you still encounter difficulty after trying the above suggestions,
call your JBL Synthesis Authorized Dealer or JBL Synthesis at
for further assistance.
Problem: Not all of the amplifiers turn on in a Synthesis system.
1. Make sure that all required DIN cables are connected between
system components. Refer to the “CONNECTING YOUR JBL
SYNTHESIS SYSTEM” section.
2. Make sure that each amplifier has its Manual On/Auto On switch
in the Auto On position.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
7.0
Rated Power Output
THD
160W per channel into 8 ohms, all channels driven
< 0.03%, 20Hz – 20kHz
>28k ohms
Input Impedance
Sensitivity
1V in = 28.28V out (THX Level)
1.25V in = 150 watts out
20Hz – 20kHz, + 0, – 0.25dB
≥100dB
Frequency Response (at 1W)
S/N Ratio (A-weighted at rated power)
Damping Factor
≥400
Power Bandwidth 1% THD
Intermodulation Distortion
Dimensions (H x W x D)
Net Weight
5Hz – 100kHz, + 0, – 3dB
0.03%
7" x 19" x 19-1/2" (178mm x 484mm x 495mm)
97 Ib (44kg)
Packaged Weight
111 Ib (50kg)
All features and specifications are subject to change without notice.
®
A Harman International Company
JBL Consumer Products
8500 Balboa Boulevard
Northridge, CA 91329
250 Crossways Park Drive
Woodbury, NY 11797
516.255.4JBL
Part No. S5160/120OM
Download from Www.Somanuals.com. All Manuals Search And Download.
|