DrivePack® DPC-2
Product User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Section 1. Safety Instructions.....................................................................................Page 4
Section 2. Before You Begin .......................................................................................Page 7
Section 3. Introduction to VP Series Powered Loudspeaker Systems ..................Page 8
Specifications by model
Section 4. VP Series Transducers ..............................................................................Page 10
Section 5. Enclosure Care and Maintenance............................................................Page 11
Section 6. Rigging and Suspension ...........................................................................Page 12
Safety Precautions
Industry Resources
Section 7. JBL DrivePack® Technology .....................................................................Page 15
AC Power Module, Electrical Information
Section 8. Input Panel Information.............................................................................Page 19
Section 9. JBL Professional Warranty .......................................................................Page 24
Section 10. Factory Contact Information ....................................................................Page 25
JBL Professional
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1 : SAFETY INSTRUCTIONS
Important
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus
to rain or moisture.
16. Do not expose this equipment to dripping or splashing and ensure that no objects filled with
liquids, such as vases, are placed on the equipment.
17. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord
plug from the AC receptacle.
18. The mains plug of the power supply cord shall remain readily operable.
Venue Performance Series User’s Guide
4
Download from Www.Somanuals.com. All Manuals Search And Download.
�������
����������������������
������������
THIS APPARATUS CONTAINS POTENTIALLY LETHAL VOLTAGES. TO PREVENT ELECTRIC SHOCK OR
HAZARD, DO NOT REMOVE DRIVEPACK CHASSIS, INPUT MODULE OR AC INPUT COVERS. NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WATCH FOR THESE SYMBOLS
The lightning bolt triangle is used to alert the user to the risk of electric shock.
The exclamation point triangle is used to alert the user to important operating or
maintenance instructions.
FCC COMPLIANCE NOTICE
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CSA COMPLIANCE NOTICE
CSA Certification Applies to Amplifier Module Only
JBL Professional
5
Download from Www.Somanuals.com. All Manuals Search And Download.
JBL DRIVEPACK® DECLARATION OF CONFORMITY
Safety and EMC Compliance Specifications
EN 55103-1:1997 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-
Visual and Entertainment Lighting Control Apparatus for Professional Use, Part 1: Emissions
EN 55103-1:1997 Magnetic Field Emissions-Annex A @ 10 cm and 1 M
EN 55022:2003 Limits and Methods of Measurement of Radio Disturbance Characteristics of ITE:
Radiated, Class B Limits; Conducted, Class A
EN 55103-2:1997 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-
Visual and Entertainment Lighting Control Apparatus for Professional Use, Part 2: Immunity
EN 61000-4-2: A2:2001 Electrostatic Discharge Immunity (Environment E2-criteria B, 4 kV Contact,
8 kV Air discharge)
EN 61000-4-3:2003 Radiated, Radio-frequency, Electromagnetic Immunity (Environment E2, criteria
A)
EN61000-4-4:2005 Electrical Fast Transient/Burst Immunity (criteria B)
EN 61000-4-5:2001 Surge Immunity (criteria B)
EN 61000-4-6:1996 Immunity to Conducted Disturbances Induced by Radio-Frequency Fields
(criteria A)
EN 61000-4-11:2004 Voltage Dips, Short Interruptions and Voltage Variation
UL 6500 2nd Edition 1999 Audio/Video and Musical Instrument Apparatus for Household,
Commercial and Similar General Use
CAN/CSA E60065-00 Audio, Video and Similar Electronic Apparatus – Safety Requirements
Venue Performance Series User’s Guide
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2 : BEFORE YOU BEGIN
The VP Series loudspeakers covered by this manual are not intended for fixed installation in outdoor or
high moisture environments. Moisture can damage the speaker cone and surround and cause corrosion of
electrical contacts and metal parts. Avoid exposing the speakers to direct moisture. Keep loudspeakers out
of extended or intense direct sunlight. The driver suspension will prematurely dry out and finished surfaces
may be degraded by long-term exposure to intense ultra-violet (UV) light.
The VP Series loudspeakers can generate considerable energy. When placed on a slippery surface such as
polished wood or linoleum, the speaker may move due to its acoustical energy output. Precautions should
be taken to assure that the speaker does not fall off a stage or table on which it is placed.
Stand mounting safety precautions
Some VP Series models can be used with an optional stand mount accessory allowing mounting on
tripod stands or on a pole over subwoofers. When using stands or poles, be sure to observe the following
precautions:
Check the stand or pole specification to be certain the device is designed to support the weight of
the speaker. Observe all safety precautions specified by the manufacturer.
Always verify that the stand (or subwoofer / pole) is placed on a flat, level, and stable surface and be
sure to fully extend the legs of tripod type stands. Position the stand so that the legs do not present
a trip hazard.
Route cables so that performers, production crew, and audience will not trip over them and pull the
speaker over.
Inspect the stand (or pole and associated hardware) before each use and do not use equipment with
worn, damaged, or missing parts.
Do not attempt to place more than one VP Series loudspeaker on a stand or pole.
Always be cautious in windy, outdoor conditions. It may be necessary to place additional weight (i.e.
sandbags) on the base of the stand to improve stability. Avoid attaching banners or similar items to
any part of a speaker system. Such attachments could act as a sail and topple the system.
Unless you are confident that you can handle the weight of the speaker, ask another person to help
you get it onto the tripod stand or pole.
Hearing damage, prolonged exposure to excessive SPL
VP Series loudspeakers are easily capable of generating sound pressure levels (SPL) sufficient to cause
permanent hearing damage to performers, production crew and audience members. Caution should be
taken to avoid prolonged exposure to SPL in excess of 90 dB.
Package Contents
•
•
•
•
Product User’s Guide (this document)
JBL DrivePack® self-powered loudspeaker
A.C. Power North America/Europe Cord-Set
Warranty Card
JBL Professional
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3 : INTRODUCTION TO VP SERIES
POWERED LOUDSPEAKER SYSTEMS
VP (Venue Performance) Series
The VP Series is a family of powered integrated audio loudspeaker systems featuring JBL DrivePack®
amplifier modules, designed in cooperation with Crown International. The JBL DrivePack features cutting-
edge technology such as patented high efficiency Class-I or Class D power amplifier circuitry. Loudspeaker
components include patented JBL Differential Drive® woofers. The full-range models feature the JBL 2452H-
SL large format 1.5” exit compression driver. This high frequency driver is coupled to a JBL Progressive
Transition™ (PT) Waveguide for excellent pattern control, smooth frequency response, and low distortion.
Waveguides can be rotated for either a horizontal or vertical orientation.
This guide covers the following models:
VP7210/95DP - 10” two-way with 90 x 50 degree waveguide
VP7212MDP - 12” two-way floor monitor with 50 x 90 degree waveguide
Venue Performance Series User’s Guide
8
Download from Www.Somanuals.com. All Manuals Search And Download.
VP SERIES SYSTEMS SPECIFICATIONS
VP7210/95DP
VP7212MDP
Specifications:
Specifications:
Frequency Response (+/-3dB):
80 Hz - 20 kHz
50 Hz - 20 kHz
90° x 50° rotatable waveguide
10
Frequency Response (+/-3dB):
Frequency Range (-10dB):
Coverage Pattern:
60 Hz - 18 kHz
55 Hz - 20 kHz
50° x 90° rotatable waveguide
15.8
Frequency Range (-10dB):
Coverage Pattern:
Directivity Factor (Q):
Directivity Index (DI):
Max Peak Output:
Directivity Factor (Q):
Directivity Index (DI):
Max Peak Output:
10 dB
12 dB
132 dB SPL 1m
137 dB SPL 1m
Transducer Section:
Transducer Section:
Low Frequency Section:
JBL 2261FF, 254 mm (10 in) dia., 76 mm (3 in) Dual Coil
neodymium Differential Drive®, Direct Cooled
Low Frequency Section:
JBL 2265G, 381 mm (15 in) dia., 76 mm (3 in) Dual Coil
neodymium Differential Drive®, Direct Cooled
Bandpass Nominal Impedance:
High Frequency:
2 x 2 ohms
Bandpass Nominal Impedance:
High Frequency:
4 ohms
JBL2452H-SL, 100 mm (4 in) titanium damped dia-
phragm, 1.5 in. exit
JBL2452H-SL, 100 mm (4 in) titanium damped dia-
phragm, 1.5 in. exit
Bandpass Nominal Impedance:
8 ohms
Bandpass Nominal Impedance:
8 ohms
System:
System:
DPC-2 Internal Amplification Output
(at nominal load):
1750 Watts Peak (875 Watts Continuous)
750LF/125HF Watts
DP2 Internal Amplification Output
(at nominal load):
1750 Watts Peak (875 Watts Continuous)
750LF/125HF Watts
DPC-2 Output (Continuous IEC shaped pink
noise into rated load impedance):
DPC-2 Output (Continuous IEC shaped pink
noise into rated load impedance):
DPC-2 Output Section:
LF: Dual Bridged Technology™, Class D
HF: Bridged Class D
DPC-2 Output Section:
LF: Dual Bridged Technology™, Class D
HF: Bridged Class D
Audio Input Connector:
User Controls:
XLR with loop-through
Audio Input Connector:
User Controls:
XLR with loop-through
80 Hz Subwoofer High Pass Filter, Enable/Disable
0-16 dB input Attenuator with 32 precision 0.5 dB steps
80 Hz Subwoofer High Pass Filter, Enable/Disable
0-16 dB input Attenuator with 32 precision 0.5 dB steps
Signal Processing:
DSP based, resident in Input Module.
Signal Processing:
DSP based, resident in Input Module.
System Management:
DSP based limiters for mechanical and thermal
protection
System Management:
DSP based limiters for mechanical and thermal
protection
AC Power Operating Range:
AC Line Voltage:
90-132VAC/216-264VAC, 50/60 Hz
AC Power Operating Range:
AC Line Voltage:
90-132VAC/216-264VAC, 50/60 Hz
50/60 Hz, User Select; 120V/240V (-15%, +10%)
Neutrik PowerCon (NAC 3MPA)
50/60 Hz, User Select; 120V/240V (-15%, +10%)
Neutrik PowerCon (NAC 3MPA)
AC Input Connector:
AC Loop-Thru:
AC Input Connector:
AC Loop-Thru:
Neutrik PowerCon (NAC 3MPB)
Neutrik PowerCon (NAC 3MPB)
AC Current Requirement:
Enclosure:
6A per system at 120V, 3A per system at 240V
AC Current Requirement:
Enclosure:
6A per system at 120V, 3A per system at 240V
Box Construction:
5/8 in. multi-ply exterior grade Baltic birch. Internally
braced. Black DuraFlex™ finish
Box Construction:
5/8 in. multi-ply exterior grade Baltic birch.
Internally braced. Black DuraFlex™ finish
Suspension System:
Grille:
10 M10 fittings, 2 x M6 pullback on rear
Suspension System :
Grille:
None
14 Gauge Black, powder-coated perforated steel with
foam backing
14 Gauge Black, powder-coated perforated steel with
foam backing
Dimensions (H x W x D):
Net Weight:
521 x 293 x 303 mm
20.5 x 11.5 x 11.9 in.
Dimensions (H x W x D):
Net Weight:
346 x 565 x 413 mm
13.6 x 22.3 x 16.2 in.
18.4 kg (40.5 lbs)
20.7 kg (45.5 lbs)
JBL Professional
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: VP SERIES TRANSDUCERS
2452H-SL High Frequency Compression Driver
JBL’s new 2452H-SL features a lightweight neodymium magnet structure, 4” damped laminate diaphragm
and a 1.5” exit. It is designed to deliver crystal-clear sound with superb dynamic range. The 2452H-SL is an
8 Ohm device.
Differential Drive® Low Frequency Drivers
JBL’s patented Differential Drive low frequency drivers dramatically reduces driver weight while greatly
enhancing all critical performance parameters: frequency response, power output, and distortion. The
Differential Drive technology features a unique design with heat sinks integrated into the cast aluminum
frame for a highly improved performance to weight ratio. The dual voice coil design places the neodymium
magnets inside the voice coil assembly, completing the magnetic circuit without the heavy surrounding steel
structure of conventional drivers.
For more information, see JBL Tech Note Vol. 1 Number 33, “Differential Drive Transducers”
Venue Performance Series User’s Guide
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5 : ENCLOSURE CARE AND MAINTENANCE
VP Series enclosures are constructed of 5/8-in. multi-ply exterior grade Baltic birch. Each enclosure model is
internally braced. The exterior is covered with JBL’s exclusive DuraFlex™ finish.
PAINTING JBL VP SERIES SYSTEM PRODUCTS
Each JBL Professional VP Series system model is readily paintable. The DuraFlex finish provides a lightly
textured surface that any household or industrial paint readily adheres to. The result is a speaker enclosure
that is able to blend unobtrusively into the decor of any stage set or environment.
Instructions for painting:
1. Prepare the enclosure surface by cleaning and wiping off dust and film with a damp cloth. It may be
necessary to use a mild household cleaner to remove grease. Avoid using a cloth that will deteriorate over
the textured surface.
2. Apply as many coats of paint as is required. Application can be by rolling, brushing or spraying. Care must
be taken when painting the grille. Avoid any paint or type of application that will clog the open cells in the
foam of the front grille. Depending on the type of paint, it may not be wise to spray the grille.
3. For painting systems that are installed in environmentally-hostile locations, it is recommended that an
automotive paint should be used for maximum protection.
Note: for systems that will be transported on a regular basis, oil-based paints or Krylon-type spray paints will
give better long-term results than water-based Latex type paints.
JBL Professional
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6 : RIGGING AND SUSPENSION
Safety Precautions
Before attempting to suspend your speakers, read and understand the following safety information.
IMPORTANT RIGGING SAFETY WARNING!
The information in this section has been assembled from recognized engineering data and is intended for
informational purposes only. None of the information in this section should be used without first obtaining
competent advice with respect to applicability to a given circumstance. None of the information presented
herein is intended as a representation or warranty on the part of JBL. Anyone making use of this information
assumes all liability arising from such use.
All information presented herein is based upon materials and practices common to North America and may
not directly apply to other countries because of differing material dimensions, specifications, and/or local
regulations. Users in other countries should consult with appropriate engineering and regulatory authorities
for specific guidelines.
Correct use of all hardware is required for secure system suspension. Careful calculations should always be
performed to ensure that all components are used within their rated workload before the array is suspended.
Never exceed maximum recommended load ratings.
Before suspending any speaker system always inspect all components (enclosure, rigging frames, pins, etc.)
for cracks, deformations, corrosion, missing, loose or damaged parts that could reduce strength and safety
of the array. Do not suspend the speaker until the proper corrective action has been taken. Use only load-
rated hardware when suspending VP Series loudspeakers.
Are You New to Rigging?
If you are new to rigging, you should do the following:
• Read and study JBL Technical Note Volume 1, Number 14: Basic Principles for Suspending Loudspeaker
Systems (available at http://www.jblpro.com/pub/technote/tn_v1n14.pdf).
• Know the Rules for Safe Rigging.
• Attend a safe rigging seminar, such as that presented by professionals like Rigging Seminars™ or by Chain
Motor Hoist manufacturers like Columbus McKinnon Corp. (manufacturers of the C/M Lodestar).
• Meet and establish a relationship with a licensed mechanical or structural engineer. Get in the habit of
asking them questions instead of guessing about their answers. Learn from what they tell you.
• Meet and discuss this aspect of your business with your Insurance Agent.
• Research and understand the codes, practices, and requirements in the venues where you intend to
operate your sound system.
Venue Performance Series User’s Guide
12
Download from Www.Somanuals.com. All Manuals Search And Download.
General Hardware Information
Any hardware used in an overhead suspension application must be load rated for the intended use.
Generally, this type of hardware is available from rigging supply houses; industrial supply catalogs and
specialized rigging distributors. Local hardware stores do not usually stock these products.
Attachment to Structures
A licensed Professional Engineer must approve placement and method of attachment to structures prior to
installation of any overhead object. The following performance standards should be provided to the Professional
Engineer for design purposes: Uniform Building Code as applicable, Municipal Building Code as applicable,
Seismic Code as applicable. Installation of hardware and method of attachment must be carried out in the
manner specified by the Professional Engineer. Improper installation may result in damage, injury or death.
Rigging Hardware Inspection & Maintenance
Suspension systems are comprised of mechanical devices and, as such, they require regular inspection and
routine maintenance to insure proper function ability. JBL VP Series loudspeakers must be inspected for
fatigue at least annually. The inspection shall include a visual survey of all corners and load bearing surfaces
for signs of cracking, water damage, de-lamination, or any other condition that may decrease the strength
of the loudspeaker enclosure. Accessory rigging hardware provided with or for JBL VP Series loudspeakers
must be inspected for fatigue at least annually. The inspection shall include a visual material survey for signs
of corrosion, bending or any other condition that may decrease strength of the fastener. For other fittings
used, refer to the manufacturer’s inspection and maintenance guidelines for process.
JBL is not responsible for the application of its products for any purpose or the misuse of this information
for any purpose. Furthermore, JBL is not responsible for the abuse of its products caused by avoiding
compliance with inspection and maintenance procedures or any other abuse. Prior to suspending the
system, an expert, trained and experienced in flying loudspeaker systems should inspect all rigging parts and
components.
JBL Professional
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Industry Resources
Allen Products
ATM Fly-Ware
(562) 424-1100
(562) 424-1100
1635 E. Burnett Street
Signal Hill, CA 90806
1635 E. Burnett Street
Signal Hill, CA 90806
M.A.N. Flying Systems
20 Sidar Road Brook Road
Industrial Estate
Rayleight, Essex SS6 7XF U.K.
McMaster Carr
Various locations through the U.S.A.
For a location near you, visit them online:
JBL Professional - Tech Note V1 No. 14
“Basic Principles for Suspending Loud-
speakers”
Safe Rigging
The JBL VP Series suspendable loudspeakers are supplied with built-in brackets. The system is designed to
facilitate the suspension of the loudspeaker by a qualified person familiar with rigging hardware and industry
practices. Improper installation may result in damage, injury or death.
Working Load Limit
The working load limit (WLL) of the JBL VP 7210/95DP suspendable loudspeaker shall be maintained as long
as no more than 46 kg (100 lb) is suspended by TWO (2) of the PRIMARY SUSPENSION points (M10 forged
Shoulder Eyebolts). The VP7210 includes two M6 suspension points located on the rear of the cabinet that
are solely intended for use as pullback points and are not considered as Primary Suspension points. Each
M6 fitting has a WLL of 23 kg (50 lbs).
A kit containing three M10 forged-shoulder eyebolts with washers is available as JBL Part number 229-
00009-01. For VP7210/95DP rear pullback point applications, order JBL part number 364287-001. This kit
includes one M6 forged-shoulder eyebolt with washer. For additional suspension components, contact a
professional rigging hardware supplier.
NOTE: M6 forged eyebolts used for VP7210/95DP pullback points require a minimum thread length of 25.4
mm (1in).
Venue Performance Series User’s Guide
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 : JBL DRIVEPACK® TECHNOLOGY
Introduction to the
JBL DrivePack® DPC-2 Integrated Audio System
JBL DrivePack equipped loudspeakers are a family of fully integrated audio systems, coupling industry-
leading loudspeaker technology to a combination of comprehensive digital signal processing and advanced
amplifier technology, perfectly matched to the enclosures to deliver superb audio quality and powerful
performance. Designed in cooperation with Crown International, the ultra-compact, high-power JBL
DPC-2 amplifier module features Crown’s patented Dual-Bridged Technology™ digital power amplification
circuitry and is integrated to the back of each DP-compatible loudspeaker enclosure, creating a seamless
electro-mechanical system that offers both convenience and portability along with the unmatched reliability,
accuracy and superb sound of JBL loudspeakers. DBT (Dual-Bridged Technology™) directly links discrete
amplifier channel outputs to each voice-coil in the Differential Drive loudspeaker. Electrical power transfer
to the transducer is optimized for maximum system performance. The DrivePack includes onboard DSP
functionality and includes lighted indicators displaying system status during opertion.
DrivePack Signal-Processing & Amplification Unit
The DrivePack electronics unit is intended to be used when mounted to a speaker enclosure of
5/8” minimum thickness of wood or composite material and with load impedances of 4 Ohms or 8
Ohms for low and mid frequency channels, and 8 or 16 Ohms for the high frequency channel.
OPERATING INSTRUCTIONS
All that is required to get your DP compatible loudspeaker system up and running is to verify that the main
panel voltage select switch setting is appropriate for the power in your area, connect an AC power source
to the AC Power panel via the Neutrik twist-lock PowerCon® inlet connector, and a full range line level audio
signal to the Input panel via the AUDIO IN XLR connector.
The JBL DPC-2 is equipped with a manual select 115V/230V Power Supply and can operate anywhere
in the world that has an available 100-120VAC or 200-240VAC power source. Upon initial power-up of
the DrivePack, the AC soft-start process will begin and the Blue Power LED illuminates when boot-up is
completed.
JBL Professional
15
Download from Www.Somanuals.com. All Manuals Search And Download.
AC POWER REQUIREMENTS
JBL DrivePack® DPC-2 systems are equipped with a DP multi-channel Crown Dual-Bridged Technology™
power amplifier and loudspeaker specific DSP electronics and require appropriate AC power.
CAUTION: In compliance with safety agency criteria and proper system operation, it is critical
that the system installer observe all electrical safety practices at all times and provide proper earth
grounding for all AC Power connections.
AC POWER CORD KIT
120VAC North America NEMA 5-15 Edison type AC plug to PowerCon® connector and 240V Europe CEE
7/7 Schuko type AC plug to PowerCon connector cord sets are provided with this JBL DrivePack product
for light-duty shop testing or system configuration type use.
One spare gray Neutrik (P/N NAC3FCB) PowerCon connector is included in the AC Power Cord Set for
your convenience to create a pass-through AC power cable. To create a light-duty pass-through cable
the system installer may choose to simply cut off the AC plug from one of the provided AC cord sets and
replace it with the provided Gray PowerCon AC Outlet connector. Follow the wiring convention indicated in
Table 1.
NOTE: Tighten set screws to 2.5Nm (1.8lb-ft) torque to prevent opening by hand.
USER-FABRICATED AC POWER DISTRIBUTION
System owners may choose to fabricate or purchase a custom AC Power cable infrastructure optimized for
their specific JBL DrivePack system configuration. See Table 1 for custom application wiring and connector
information.
NOTE: Parts not provided.
CAUTION: Do not exceed 80% current rating of any AC connector at any time! See AC Power
Rating Table for current draw information.
Table 1. User-Fabricated AC Cable and Connector Information
AC Inlet Cable Connector
Neutrik PowerCon® NAC3FCA quick lock 3-pole A-type
cable connector for power inlet. Rated current per contact:
20 A (rms), Rated Voltage: 250VAC.
AC Outlet Cable Connector
Neutrik PowerCon® NAC3FCB quick lock 3-pole B-type
cable connector for power outlet. Rated current per contact:
20 A (rms), Rated Voltage: 250VAC.
Wiring
Cable: screw-type terminals or soldering nom. wire size/con-
tact: 2.5 mm² / 14 AWG
Wiring convention
Ground – Ground, Neutral – Neutral, AC Hot – AC Hot
With the two non-interchangeable types of connectors (A-type, B-type) it is impossible to produce a short
circuit. Mating connectors (combination) are identified by mechanical keyways and by color.
Table 2. Power Connector Coding
A-type (POWER INLET);
B-type (POWER OUTLET)
Cable connector: Blue
Cable connector: Gray, with
Blue bushing
Venue Performance Series User’s Guide
16
Download from Www.Somanuals.com. All Manuals Search And Download.
DPC-2 AC Power Ratings
Description
115VAC
230VAC
Idle
30W
30W
Quescient Power Draw
1/8th Power, Pink Noise (UL/CSA)
1/3rd Power, Pink Noise
Maximum Power Draw
Inrush Current
85W, 1.5A rms
2 A
85W, 1A rms
1 A
1440W
Inrush current limiting via PTC soft-start
AC Power Panel Connectors (UL/CSA)
12A Max, 100-10VAC/220-240VAC, 50-60 Hz.
Class 1 Wiring
16 AWG
(1.5 mm2)
Inlet Connector Rating (UL/CSA)
Outlet Connector Rating (UL/CSA)
5A
7A
3A
9A
Line Voltage Selection: DrivePack® DPC-2 amplifier models feature a user-configurable dual-voltage
international power supply and is easily set to the appropriate local AC Power Mains voltage supply. A 2-
way slide switch is provided to select 100-120VAC or 200-240VAC operation, 50/60Hz.
Your DPC-2 amplifier module is factory set to 230 VAC operation to avoid damage from overvoltage
conditions at any location worldwide. Applying 230 VAC to the DPC-2 with the unit set to 115V can cause
serious damage. Before you set up your VP-DPC-2 series speaker for the first time, verify that the line
voltage selector setting is appropriate for the AC Mains supply voltage in your area.
Changing the AC Mains Supply Voltage Setting
• Make sure that the speaker is powered off and the AC power cable is disconnected from the speaker.
• Locate the voltage selector switch directly above the blue PowerCon connector on the main control panel.
• Slide the voltage selector switch to 115V for (100-120V~) or 230V for (220-240V~) range setting as
required for your area.
• After having reconfirmed that the correct voltage is selected, reconnect the blue AC Line Input PowerCon
connector and power the unit up.
DO NOT UNDER ANY CIRCUMSTANCES OPERATE THE UNIT WITH THE WRONG VOLTAGE
SELECTED. DOING SO MAY RESULT IN SERIOUS DAMAGE TO YOUR SPEAKER SYSTEM WHICH
WILL NOT BE COVERED BY WARRANTY.
Line Voltage Tolerance: The amp will operate normally (with expected de-rating in power output during low
line conditions) over a range of 100-120VAC +/-10% or 200-240VAC +/-10% AC input voltage. The amp will
shut down for voltages below nominal line and self protect for over-voltage beyond 15% nominal line.
CAUTION: Continuous voltages 10% beyond high line at either 120VAC or 240VAC operation
ranges can disrupt performance of the JBL DRIVEPACK! To avoid activation of amplifier low line/
high line protection which will interrupt audio performance, the system operator should maintain
AC supply voltages within the rated voltage windows.
JBL Professional
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Amplifier Protection Features
Thermal Management:
JBL DrivePack® systems are cooled by Passive Convection. No fans are used in any part of the thermal
management system. To maintain efficient cooling it is a good practice to assure open space around the
DrivePack units. In the event of excessive exposure to direct sunlight in very hot ambient conditions, it
is possible that the unit may overheat and will automatically shut down to protect itself. When its internal
temperature has returned to within its operating range it will turn back on. To prevent overheating always
ensure adequate cooling and appropriate shade.
Operating Temperature:
The system will remain touchable during quiescent operation and will not provide a burn hazard during any
operating condition.
Venue Performance Series User’s Guide
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8 : INPUT PANEL INFORMATION
Input Controls, Indicators, Connectors and Features
JBL DrivePack®--C systems are equipped with a multi-function input bay and provides flexible connectivity
options for both audio and AC power.
Audio Signal Distribution
Connecting source audio signals to the input
modules on JBL DrivePack systems is similar to
daisy-chaining multiple external amplifier channels
together.
Assuming an output device source impedance of
100 Ohms and a 10:1 load to source ratio, up to 20
JBL DrivePack units typical can be linked together
on one output source without using a distribution
amp.
JBL Professional
19
Download from Www.Somanuals.com. All Manuals Search And Download.
VP7210DP Input Panel
See Figure 1
The VP7210DP input panel features analog audio inputs and sophisticated onboard digital signal processing
technology. Precision Bandpass limiting, pre-equalization filters and automatic self-protection functions
ensure optimized performance. JBL engineers have calibrated DSP speaker management and limiter
parameters to ensure smooth phase response and transfer function curves right out of the box.
CONTROLS
1) FLAT/80 Hz HP
5 6 7
2
a) 2-Position push-button DSP preset
selection switch, enables the desired
function. When set in the “FLAT”
position, frequency response is linear
and unaltered. When 80 Hz HP is
selected, the system high pass filter
is raised to 80 Hz, creating an 80
Hz crossover point compatible with
external subwoofers.
3
4
1
8
2) ATTENUATION
a) 16 dB Precision Detented rotary input
sensitivity control, 0.5 dB steps.
Sensitivity +4 dBu nominal (+20 dBu
clip) with the control fully counter
clockwise, and -10 dBv nominal
(+4 dBu clip) with the control fully
clockwise.
10
11
9
3) RESET
a) Press to reset line voltage circuit breaker.
4) LINE SELECT
figure 1
a) 2-position slide switch, set to 115V position
for (100-120V~) or 230V position for (220-240V~) operation.
INDICATORS
5) PEAK
a) (Clip) Red LED, Clip detection monitors input, DSP, and each amplifier output channel. The LED illuminates
when overload at any point is detected.
6) SIG
a) (Signal) Green LED, detects input signal, illuminates above the threshold set at –70 dBu.
7) POWER
a) Blue LED – located near voltage select switch, illuminates when AC power is applied and unit is ready for
operation.
Venue Performance Series User’s Guide
20
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTORS
8) Audio In
a) F-XLR Active 20K Ohm Balanced, 10K Ohm Unbalanced.
b) Pin 2 Hot (Positive voltage produces outward cone motion of L.F. Transducers).
9) Audio Out
a) M-XLR Passive Audio Pass-through.
b) Pin 2 Hot (Positive voltage produces outward cone motion of L.F. Transducers).
10) AC LINE INPUT
a) Blue Neutrik PowerCon® NAC3MPA A-type air tight twist-lock chassis connector for AC power inlet.
b) The mating blue cable connector is keyed and will insert in only one orientation. Electrical connection is made
when the AC plug is fully inserted and twisted clockwise until locked into position.
11) AC LOOP OUTPUT
a) Gray Neutrik PowerCon® NAC3MPB B-type air tight twist-lock power outlet connector is provided to loop AC
power through to additional units.
b) The mating gray outlet cable connector is keyed and will insert in only one orientation. Electrical connection is
made upon fully inserting the AC plug and twisting clockwise until locked into position.
c) To accomplish loop-thru AC power connections, simply attach a PowerCon jumper cable from the gray
connector of the first loudspeaker system to the blue connector of the second, etc. Blue Inlet and Gray
Outlet connectors are not interchangeable.
CAUTION: Looping more than three DPC-2 systems together is not recommended! Do not
exceed 80% current rating of any AC connector at any time! Refer to AC Power Rating Tables in
this document for current draw information.
JBL Professional
21
Download from Www.Somanuals.com. All Manuals Search And Download.
VP7212MDP Input Panel
See Figure 2
The VP7212MDP input panel is optimized for high impact stage monitor use and features analog audio
inputs and sophisticated onboard digital signal processing technology. Precision Bandpass limiting, pre-
equalization filters and application specific DSP presets ensure flexible and reliable performance. JBL
engineers have calibrated DSP speaker management and limiter parameters to ensure smooth phase
response and transfer function curves right out of the box.
8
1
9
CONTROLS
1) DUAL WEDGE TUNING
a) 2-Position DSP preset selection switch, enables the
desired function. When set in the “SINGLE” position,
frequency response is optimized for single wedge
performance. In the “DUAL” position, low and mid-
high frequencies are contoured to optimize dual wedge
coupling.
2) ATTENUATION
2
5
7
a) 16 dB Precision Detented rotary input
sensitivity control, 0.5 dB steps.
Sensitivity +4 dBu nominal (+20 dBu
clip) with the control fully counter
clockwise, and -10 dBv nominal
(+4 dBu clip) with the control fully
clockwise.
3) RESET
a) Press to reset line voltage circuit breaker.
4) LINE SELECT
a) 2-position slide switch, set to 115V position for (100-
120V~) or 230V position for (220-240V~) operation.
3
INDICATORS
figure 2
5) PEAK
10
11
4
a) (Clip) Red LED, Clip detection monitors input, DSP, and
each amplifier output channel. The LED illuminates when overload at any point is detected.
6) SIG
a) (Signal) Green LED, detects input signal, illuminates above the threshold set at –70 dBu.
7) POWER
a) Blue LED – located near voltage select switch, illuminates when AC power is applied and unit is ready for
operation.
Venue Performance Series User’s Guide
22
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTORS
8) Audio In
a) F-XLR Active 20K Ohm Balanced, 10K Ohm Unbalanced.
b) Pin 2 Hot (Positive voltage produces outward cone motion of L.F. Transducers).
9) Audio Out
a) M-XLR Passive Audio Pass-through.
b) Pin 2 Hot (Positive voltage produces outward cone motion of L.F. Transducers).
10) AC LINE INPUT
a) Blue Neutrik PowerCon® NAC3MPA A-type air tight twist-lock chassis connector for AC power inlet.
b) The mating blue cable connector is keyed and will insert in only one orientation. Electrical connection is made
when the AC plug is fully inserted and twisted clockwise until locked into position.
11) AC LOOP OUTPUT
a) Gray Neutrik PowerCon® NAC3MPB B-type air tight twist-lock power outlet connector is provided to loop AC
power through to additional units.
b) The mating gray outlet cable connector is keyed and will insert in only one orientation. Electrical connection is
made upon fully inserting the AC plug and twisting clockwise until locked into position.
c) To accomplish loop-thru AC power connections, simply attach a PowerCon jumper cable from the gray
connector of the first loudspeaker system to the blue connector of the second, etc. Blue Inlet and Gray
Outlet connectors are not interchangable.
CAUTION: Looping more than three DPC-2 systems together is not recommended! Do not
exceed 80% current rating of any AC connector at any time! Refer to AC Power Rating Tables in
this document for current draw information.
JBL Professional
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Venue Performance Series User’s Guide
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9 : JBL LIMITED WARRANTY
The JBL Limited Warranty on professional loudspeaker products (except for enclosures) remains in effect for
five years from the date of the first consumer purchase. JBL DrivePack® amplifiers are warranted for three
years from the date of original purchase. Enclosures and all other JBL products are warranted for two years
from the date of original purchase.
Who Is Protected by This Warranty?
Your JBL Warranty protects the original owner and all subsequent owners so long as: A.) Your JBL product
has been purchased in the Continental United States, Hawaii or Alaska. (This Warranty does not apply
to JBL products purchased elsewhere except for purchases by military outlets. Other purchasers should
contact the local JBL distributor for warranty information.); and B.) The original dated bill of sale is presented
whenever warranty service is required.
What does the JBL Warranty cover?
Except as specified below, your JBL Warranty covers all defects in material and workmanship. The following
are not covered: Damage caused by accident, misuse, abuse, product modification or neglect; damage
occurring during shipment; damage resulting from failure to follow instructions contained in your Instruction
Manual; damage resulting from the performance of repairs by someone not authorized by JBL; claims based
upon any misrepresentations by the seller; any JBL product on which the serial number has been defaced,
modified or removed.
Who Pays for What?
JBL will pay all labor and material expenses for all repairs covered by this warranty. Please be sure to save
the original shipping cartons because a charge will be made if replacement cartons are requested. Payment
of shipping charges is discussed in the next section of this warranty.
How to Obtain Warranty Performance
If your JBL product ever needs service, write or telephone us at JBL Incorporated (Attn: Customer Service
Department), 8500 Balboa Boulevard, PO. Box 2200, Northridge, California 91329 (818/893-8850). We may
direct you to an authorized JBL Service Agency or ask you to send your unit to the factory for repair. Either
way, you’ll need to present the original bill of sale to establish the date of purchase. Please do not ship your
JBL product to the factory without prior authorization. If transportation of your JBL product presents any
unusual difficulties, please advise us and we may make special arrangements with you. Otherwise, you are
responsible for transporting your product for repair or arranging for its transportation and for payment of
any initial shipping charges. However, we will pay the return shipping charges if repairs are covered by the
warranty.
Limitation of Implied Warranties
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.
EXCLUSION OF CERTAIN DAMAGES
JBL’S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT OUR OPTION, OF ANY DEFECTIVE
PRODUCT AND SHALL NOT INCLUDE INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR
DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY, FROM STATE TO STATE.
JBL Professional
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10 : JBL CONTACT INFORMATION
Mailing Address:
Outside the USA:
JBL Professional
8500 Balboa Blvd.
Northridge, CA 91329 USA
Contact the JBL Professional Distributor in
your area. A complete list of JBL Professional
international distributors is provided at our
Shipping Address:
JBL Professional
Product Registration:
8370 Balboa Blvd., Dock D
Register your product online at:
Northridge, CA 91329 USA
(Do not return product to this address without
first obtaining prior authorization from JBL)
Customer Service:
Monday through Friday
8:00am - 5:00pm
Pacific Coast Time In the U.S.A.
(800) 8JBLPRO (800.852.5776)
On the World Wide Web:
WEB LINKS
JBL Professional:
VP Series Products:
JBL Customer Service:
VP Series E-mail Address:
Harman Pro Internet Portal:
Venue Performance Series User’s Guide
26
Download from Www.Somanuals.com. All Manuals Search And Download.
JBL Professional
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Number: 363642-002
VP PROD GUIDE
0607
8500 Balboa Boulevard
Northridge, CA 91329 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|