High Output
Indoor/Outdoor
®
Control 28
Background/Foreground Speaker
Professional Series
Key Features:
᭤
Components: 8” Polypropylene
coated woofer, 1” Titanium coated
horn loaded tweeter.
᭤
᭤
Built-in InvisiBallTM mounting
hardware*
Weather resistant enclosure and
transducers
᭤
᭤
᭤
᭤
Readily paintable
90° x 90° high frequency horn
Overload Protection Circuitry
Sensitivity: 92 dB SPL, 1W, 1m
*Patents pending worldwide
The Control® 28 is the largest of
JBL Professional’s Control Contractor
Series indoor/outdoor loudspeakers.
Its rich sonic character makes the
Control® 28 a perfect choice for
restaurants, health clubs, under bal-
cony, outdoor theme & water parks,
or other applications where fore-
ground/background music and pag-
ing are required.
Specifications:
Frequency Range (-10 dB)1: 60Hz to 16kHz
Continuous Program:
Power Capacity2: 175 Watts
Sensitivity3: 92 dB SPL, 1W, 1m
Directivity Factor (Q): 7.5
Directivity Index (DI): 8.8
Nominal Impedance: 8 ohms
Crossover Frequency: 2.8kHz
LF Driver: 200mm (8 in) Polypropylene cone w/WeatherEdge
HF Driver: 25mm (1 in) Titanium coated polycarbonate
Enclosure Material: HIPS (High Impact Polystyrene)
Overload Protection: Full-Range power limiting to protect network and transducers
Termination: Spring terminals, accepts banana plug
The unique and global patent
pending InvisiBall™ mounting hard-
ware is included in each system and
makes short work of permanent
installation. The InvisiBall™ mounting
method adds the benefit of vertical
rotation of up to 37° off-axis and hor-
izontal rotation of up to 44° off-axis.
Because InvisiBall™ adjustments are
made through a hidden access
behind the logo badge, the grill
never needs to be removed and there
exists a high degree of theft deter-
rence as well.
Environmental: Conforms to Mil Spec 810 for humidity, salt spray,
temperature & UV. IEC 529 IP-X4 splashproof rating.
Dimensions (H x W x D): 380 x 280 x 220 mm (15.0 x 11.0 x 8.6 in)
Net Weight (ea): 5.5kg (12 lbs)
Shipping Weight (pr): 11kg (25 lbs)
Included Accessories: Invisiball Assembly
6mm x 180mm hex key
Optional Accessories:
MTC-28V: For vertical columnar orientation of up to 3 loudspeakers
MTC-28H: For horizontal splaying of two speakers. Three brackets array
up to six loudspeakers in a 360° array.
The Control® 28 readily accepts a
variety of paints and finishes to
match any decor.
MTC-28/25CM: Ceiling-mount adapter.
1Half-space (on-wall).
Weather resistance is maximized by
coating the woofer cone in
2Continuous program power is a conservative expression of the system’s ability to handle normal speech and music
program material and is defined as 3dB above the Continuous Pink Noise Rating (IEC-shaped pink noise with a 6dB
crest factor, for 100 hours continuously).
polypropylene and terminating its cir-
cumference in JBL’s WeatherEdge™, a
seamless, rubberized extension of the
woofer surround that provides added
protection to critical transducer ele-
ments. The polycarbonate tweeter
diaphragm is reinforced with a thin
film of titanium for added rigidity and
endurance against sun, salt and mois-
ture. Zinc plated grilles resist rusting
in the harshest conditions.
3Half-space (on-wall), ave 100Hz to 10 kHz.
JBL continually engages in research related to product improvement. Changes introduced into existing products without
notice are an expression of that philosophy.
Available in black (Control 28) and
white (Control 28-WH).
Download from Www.Somanuals.com. All Manuals Search And Download.
Horizontal 1/3 Octave Polars
Architectural Specifications:
The loudspeaker shall consist of a 200mm (8 in) low frequency trans-
ducer, 25mm (1 in) high frequency transducer, and frequency dividing
network installed in a ported enclosure. The low frequency voice coil
shall be 32 mm (1-1/4 in) in diameter.
Performance specifications of a typical production unit shall be as fol-
lows: Measured sensitivity (SPL at 1 m [3.3ft] with 2.83V input, averaged
from 500 Hz to 1.5 kHz) shall be at least 92 dB-SPL. Usable frequency
response shall extend from 60 Hz to 16 kHz (10 dB below rated sensitiv-
ity, in half-space, with no external equalization). Nominal impedance
shall be 8 ohms. The frequency dividing network shall have a crossover
frequency of 2.8 kHz. Rated power capacity shall be at least 175 watts
continuous program power, defined as 3dB above a test signal of filtered
random noise conforming to international standard IEC268-5 (shaped
pink noise with a peak-to-average ratio of 6dB), for 100 continuous
hours duration.
The system shall be protected against damage from occassional over-
powering via full range series lamps that limits the power to the net-
work and transducers. The high frequency transducer shall be horn-
loaded to more evenly cover a nominal 90° horizontal by 90° vertical
area.
The enclosure shall be constructed of high-impact polystyrene for pro-
tection against the elements in outdoor applications, and for paintability.
The grille shall be completely zinc-coated for resistance against rusting,
shall be bake-painted black, and shall be secured via screws to keep it
in place when facing downward.
The low frequency transducer shall have a polypropelene cone and a
butyl rubber surround which shall extend seamlessly over the edge of
the speaker frame for protection against the elements. The high frequen-
cy transducer shall be constructed of polycarbonate, reinforced with a
titanium film for additional weather resistance. The system shall with-
stand Mil Spec 810 testing with specified time durations for exposure to
the following environments with no effect on its acoustical performance
or structural integrity: salt spray (method 509.3), temperature -19°C to
49°C (method 501.3 and 502.3), 95% humidity (method 507.3) and ultra-
violet (method 505.3). The system shall have a IEC 529 splashproof rat-
ing of IP-X4.
For theft deterrence, the installation access area shall be hidden
behind a snap-out cover, and the access area shall be on the front of the
loudspeaker for ease of installation and adjustment. The loudspeaker
shall be rotatable over a minimum of ±35° in all directions via a ball-
type mounting system. The ball mechanism shall be internal to the cabi-
net to allow low-profile mounting and better stability via a short moment
arm. The logo shall be rotatable for proper orientation when the loud-
speaker is mounted horizontally or vertically.
The external wiring connectors shall be spring loaded and gold plat-
ed, and shall accept bare wire, single or dual banana-type connectors
with 19 mm (3/4 in) spacing. Overall cabinet dimensions shall be no
greater than 380 mm (15.0 in) high by 280 mm (11.0 in) wide by 220
mm (8.6 in) deep and shall weigh no more than 5.5 kg (12 lbs).
The finish shall be a paintable lighly textured black.
The system shall be the JBL Model Control 28 with included
InvisiballTM mounting system.
Download from Www.Somanuals.com. All Manuals Search And Download.
®
᭤ Control 28 High Output Indoor/Outdoor Background/Foreground Speaker
Vertical 1/3 Octave Polars
JBL Professional
8500 Balboa Boulevard, P.O. Box 2200
Northridge, California 91329 U.S.A.
SS Control 28
CRP 20M
5/97
A Harman International Company
Download from Www.Somanuals.com. All Manuals Search And Download.
|