JBL Portable Speaker CONTROL NOW User Manual

®
JBL® CONTROL® SERIES  
JBL CONTROL NOW™  
JBL CONTROL NOWAW  
OWNER’S GUIDE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOME THEATER  
PLACEMENT  
For front-channel use, place one speaker on the left and another on the right,  
along either side of the television monitor. Since the speakers are magnetically  
shielded, you can place them near a CRT TV without worrying about the field  
distorting the TV picture.  
JBL Control NOW speakers are perhaps the most flexible and versatile loud-  
speakers ever developed. There are numerous mounting options. The JBL  
Control NOW speaker can be wall-mounted or corner-mounted, sit on a shelf or  
be used with floor stands. Two, three or four speakers can be joined together  
to create loudspeaker solutions for virtually any application.  
For surround-channel use, place speakers in corners, on the wall, on bookshelves  
or on stands alongside the listening position. Final placement depends on room  
acoustics, availability of space and your listening preference.  
• Use single units as shelf, stand- or wall-mounted speakers in traditional  
stereo or home theater applications.  
In 6- or 7-channel configurations, place the rear channel(s) behind the listening  
position, as shown in Figure 2.  
• Join two speakers together to form a visually striking array in single-channel  
applications or as a single-point stereo or surround speaker such as rear  
surround left and rear surround right.  
NOTE: A JBL powered subwoofer will add impact and realism to both  
music and film soundtracks. Contact your JBL dealer for recommendations  
on subwoofer models for your application.  
• Connect three speakers around an outer corner and send full-range sound  
throughout two adjacent rooms.  
• Suspend four JBL Control NOW speakers from the ceiling, using standard  
ceiling-fan hardware and the optional pole-mount bracket (not included).  
Configure each four-speaker array for use as a single-channel or  
single-point stereo.  
Left  
Front  
Channel  
Right  
Front  
JBL  
Subwoofer  
(optional)  
Center  
Channel  
Channel  
This owner's guide will cover the installation and wiring procedures for each  
mounting option. Simply decide how you will mount and use the speakers, and  
then follow the instructions for your specific application.  
Please note that while the JBL Control NOW AW speaker is an all-weather  
outdoor loudspeaker, it is not waterproof. The speaker should not be  
submerged or directly exposed to water, ice, snow or sustained moisture.  
JBL Control NOW speakers are designed for indoor use only.  
STEREO  
Couch  
Before deciding where to place your speakers, survey your room and think about  
placement. Keep the following points in mind, and use Figure 1 as a guide:  
Left  
Surround  
Channel  
Right  
Surround  
Channel  
• For best results, place the speakers 6'– 8' (1.5m–2.5m) apart.  
Left Rear  
Channel  
Center Rear  
Channel  
Right Rear  
Channel  
• Position each speaker so that the tweeter is directed toward the  
listening area.  
• Generally, bass output will increase as the speaker is moved closer to  
a wall or corner.  
Figure 2. This overhead view shows a typical home theater plan. Left/right  
rear channels are for a 7-channel system. The center rear channel is for  
a 6-channel system.  
• Refer to the “Home Theater” section at right if you also plan to use the  
speakers for home theater reproduction.  
Left  
Channel  
Right  
Channel  
Listening Position  
Figure 1. Experiment with speaker placement to obtain the best bass level  
and stereo imaging in your room.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT:Make sure all equipment is turned off before making  
any connections. For speaker connections, use a high-quality speaker wire  
with polarity coding. The side of the wire with a ridge or other coding is  
usually considered positive polarity (i.e., +).  
WALL SURFACE-MOUNTING  
When deciding upon a location for the JBL Control NOW speaker, take care  
NOT to install the mounting bracket closer than 3" (horizontal) and 8-1/2" (vertical)  
to the ceiling. Any closer than the minimum measurements will not allow  
the room needed to position and slide the JBL Control NOW speaker into the  
mounting bracket.  
NOTE: If desired, consult your local JBL dealer about speaker wire and  
connection options.  
The speakers have coded terminals that  
accept a variety of wire connectors. The most  
1. Strip 1/4" of wire  
2. Press and push connector  
CAUTION  
3. Insert bare end;  
common connection is shown in the diagram  
to the left. To ensure proper polarity, connect  
each + terminal on the back of the amplifier  
or receiver to the respective + (red) terminal  
on each speaker, as shown. Connect the  
– (black) terminals in a similar way. See  
the owner’s guides that were included with  
your amplifier, receiver and television to  
confirm connection procedures.  
The customer is responsible for proper selection and use of mounting hardware  
(available through hardware stores), to properly and safely wall-mount the  
speakers. The JBL Control NOW speaker was designed to be easily installed.  
However, if you are unable to clearly and fully understand and follow the  
instructions in this manual, or if you are unsure of your ability to properly install  
these loudspeakers, please contact your dealer or a qualified installer. Please  
do not use any power tools during installation. Power tools can exert excessive  
and unnecessary torque which, in turn, can damage fasteners or other parts  
and accessories, reducing their strength and causing possible failure of the  
fastener or part. A failed or damaged fastener or part may not be able to  
perform as designed, and may lead to an unsafe installation.  
release push connector  
BLACK = —  
RED = +  
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making  
connections. Doing so will cause poor imaging and diminished bass response.  
Standard  
Connection  
1. Run the wiring to the location desired for mounting the JBL Control NOW speaker.  
2. Using a level, secure the mounting bracket to the wall. Be sure to use an  
appropriate anchor.  
3"Minimum distance  
Corner/Wall-Mount-  
Bracket Assembly  
Wiring diagram shows  
polarity connections for  
one channel of a stereo or  
from ceiling  
to top of bracket  
(horizontal mount)  
8-1/2" Minimum distance  
from ceiling  
to top of bracket  
(vertical mount)  
BLACK = —  
home theater system.  
RED = +  
Appropriate  
anchors  
NOTE:There are two  
cable access holes  
provided in the Wall-  
Mount Assembly.  
3. Connect the wires to the JBL Control NOW speaker.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. The mounting bracket is designed to trap the flange of the JBL Control NOW  
speaker by securing the mounting-bracket cap with two screws through the  
bottom of the mounting bracket. Rest the JBL Control NOW speaker’s rear  
flange in the mounting bracket, as shown. This will support the weight of the  
speaker. Slide the mounting-bracket cap over the assembly. Secure the  
mounting-bracket cap by inserting two #10-32 x 2" screws (provided) in  
the bottom of the mounting bracket and tightening.  
An alternate  
vertical orientation  
is shown here  
Mounting-Bracket Cap  
Vertical  
orientation  
Mounting Bracket  
(side view)  
Bracket Cover  
#10-32 x 2" Screws (2)  
(side view)  
Mounting-Bracket Cap  
Mounting Bracket  
Vertical  
orientation  
Bracket Cover  
Mounting Bracket  
shown as looking through  
the speaker.  
#10-32 x 2"Screws (2)  
Regardless of whether you choose a vertical or horizontal orientation,  
when mounting the JBL Control NOW speaker to a single wall surface, you  
should always install the wall-mounting bracket in a vertical orientation.  
5. To orient the JBL logo into the correct position, pull the JBL logo slightly  
outward from the speaker grille and rotate. The JBL logo is held in place by  
a spring. Peel the adhesive cover off the mounting-bracket cover and attach  
to the top and bottom of the mounting assembly.  
Mounting-Bracket  
Cover  
Mounting-Bracket  
Cover  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
WALL CORNER-MOUNTING  
CAUTION  
3. Connect the wires to the JBL Control NOW speaker.  
The customer is responsible for proper selection and use of mounting hardware  
(available through hardware stores), to properly and safely wall-mount the  
speakers. The JBL Control NOW speaker was designed to be easily installed.  
However, if you are unable to clearly and fully understand and follow the  
instructions in this manual, or if you are unsure of your ability to properly install  
these loudspeakers, please contact your dealer or a qualified installer. Please  
do not use any power tools during installation. Power tools can exert excessive  
and unnecessary torque which, in turn, can damage fasteners or other parts  
and accessories, reducing their strength and causing possible failure of the  
fastener or part. A failed or damaged fastener or part may not be able to  
perform as designed, and may lead to an unsafe installation.  
IMPORTANT:Make sure all equipment is turned off before making  
any connections. For speaker connections, use a high-quality speaker wire  
with polarity coding. The side of the wire with a ridge or other coding is  
usually considered positive polarity (i.e., +).  
When deciding upon a location for the JBL Control NOW speaker, take care  
NOT to install the mounting bracket closer than 3" (horizontal) and 8-1/2" (vertical)  
to the ceiling. Any closer than the minimum measurements will not allow  
the room needed to position and slide the JBL Control NOW speaker into  
the mounting bracket.  
NOTE: If desired, consult your local JBL dealer about speaker wire and  
connection options.  
The speakers have coded terminals that  
accept a variety of wire connectors. The most  
1. Strip 1/4" of wire  
2. Press and push connector  
1. Run the wiring to the location desired  
for mounting the JBL Control NOW  
speaker.  
3. Insert bare end;  
common connection is shown in the diagram  
to the left. To ensure proper polarity, connect  
each + terminal on the back of the amplifier  
or receiver to the respective + (red) terminal  
Corner/Wall-Mount-  
Bracket Assembly  
release push connector  
BLACK = —  
RED = +  
on each speaker, as shown. Connect the  
– (black) terminals in a similar way. See  
the owner’s guides that were included with  
your amplifier, receiver and television to  
confirm connection procedures.  
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making  
connections. Doing so will cause poor imaging and diminished bass response.  
NOTE:There are two  
cable access holes  
provided in the Wall-  
Mount Assembly.  
Standard  
Connection  
2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors.  
Wiring diagram shows  
polarity connections for  
one channel of a stereo or  
3"Minimum  
distance from ceiling  
(horizontal mount)  
8-1/2" Minimum  
BLACK = —  
home theater system.  
RED = +  
distance from ceiling  
(vertical mount)  
Appropriate  
anchors  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. The mounting bracket is designed to trap the flange of the JBL Control NOW  
speaker by securing the mounting-bracket cap with two screws through the  
bottom of the mounting bracket. Rest the JBL Control NOW speaker’s rear  
flange in the mounting bracket, as shown. This will support the weight of the  
speaker. Now slide the mounting-bracket cap over the assembly. Secure the  
mounting-bracket cap by inserting two #10-32 x 2" screws (provided) in the  
bottom of the mounting bracket and tightening.  
5. To orient the JBL logo into the correct position, pull the JBL logo slightly  
outward from the speaker grille and rotate. The JBL logo is held in place by  
a spring. Peel the adhesive cover off the mounting-bracket cover and attach  
to bottom of mounting assembly.  
Mounting-Bracket Cap  
Mounting Bracket  
(side view)  
Mounting-Bracket Cover  
#10-32 x 2" Screws (2)  
(side view)  
Ceiling line  
Top Cap  
Mounting Bracket  
#10-32 x 2" Screws (2)  
Mounting Bracket  
shown as looking through  
the speaker.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
WALL/CEILING CORNER-MOUNTING  
(VERTICAL MOUNTING ONLY)  
3. Connect the wires to the JBL Control NOW speaker.  
CAUTION  
The customer is responsible for proper selection and use of mounting hardware  
(available through hardware stores), to properly and safely wall-mount the  
speakers. The JBL Control NOW speaker was designed to be easily installed.  
However, if you are unable to clearly and fully understand and follow the  
instructions in this manual, or if you are unsure of your ability to properly install  
these loudspeakers, please contact your dealer or a qualified installer. Please  
do not use any power tools during installation. Power tools can exert excessive  
and unnecessary torque which, in turn, can damage fasteners or other parts  
and accessories, reducing their strength and causing possible failure of the  
fastener or part. A failed or damaged fastener or part may not be able to  
perform as designed, and may lead to an unsafe installation.  
IMPORTANT:Make sure all equipment is turned off before making  
any connections. For speaker connections, use a high-quality speaker wire  
with polarity coding. The side of the wire with a ridge or other coding is  
usually considered positive polarity (i.e., +).  
When deciding upon a location for the JBL Control NOW speaker, take care  
NOT to install the mounting bracket closer than 3" to a side wall. Any closer  
than 3" will not allow the room needed to position and slide the JBL Control NOW  
speaker into the mounting bracket.  
NOTE: If desired, consult your local JBL dealer about speaker wire and  
connection options.  
The speakers have coded terminals that  
accept a variety of wire connectors. The most  
1. Strip 1/4" of wire  
2. Press and push connector  
3. Insert bare end;  
common connection is shown in the diagram  
to the left. To ensure proper polarity, connect  
each + terminal on the back of the amplifier  
or receiver to the respective + (red) terminal  
release push connector  
BLACK = —  
RED = +  
on each speaker, as shown. Connect the  
– (black) terminals in a similar way. See  
the owner’s guides that were included with  
your amplifier, receiver and television to  
confirm connection procedures.  
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making  
connections. Doing so will cause poor imaging and diminished bass response.  
3" Minimum  
distance from wall  
Standard  
Connection  
Wiring diagram shows  
polarity connections for  
one channel of a stereo or  
1. Run the wiring to the location desired for mounting the JBL Control NOW speaker.  
2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors.  
BLACK = —  
home theater system.  
RED = +  
Appropriate  
anchors  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. The mounting bracket is designed to trap the flange of the JBL Control NOW  
speaker by securing the mounting-bracket cap with two screws through the  
side of the mounting bracket. Rest the JBL Control NOW speaker’s flange in  
the mounting bracket, as shown. This will support the weight of the speaker.  
Now slide the mounting-bracket cap over the assembly. Secure the mounting-  
bracket cap by inserting two #10-32 x 2" screws (provided) in the side of the  
mounting bracket and tightening.  
5. To orient the JBL logo into the correct position, pull the JBL logo slightly  
outward from the speaker grille and rotate. The JBL logo is held in place by  
a spring. Peel the adhesive cover off the mounting-bracket cover and attach  
to sides of the mounting assembly.  
Bracket  
Cover  
#10-32 x 2"  
Screws (2)  
Top Cap  
Mounting  
Bracket  
Mounting Bracket  
shown as looking through  
the speaker.  
#10-32 x 2"  
Screws (2)  
Mounting  
Bracket  
Top Cap  
This illustration shows  
speaker viewed from  
beneath.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors.  
HALF-ROUND WALL-MOUNTING  
(HORIZONTAL OR VERTICAL)  
NOTE: Decide whether you will connect the speakers as a single channel  
or two separate channels, and follow the appropriate instructions on  
the following pages.  
CONNECT AS A SINGLE CHANNEL  
CAUTION  
Appropriate  
anchors  
The customer is responsible for proper selection and use of mounting hardware  
(available through hardware stores), to properly and safely wall-mount the  
speakers. The JBL Control NOW speaker was designed to be easily installed.  
However, if you are unable to clearly and fully understand and follow the  
instructions in this manual, or if you are unsure of your ability to properly install  
these loudspeakers, please contact your dealer or a qualified installer. Please  
do not use any power tools during installation. Power tools can exert excessive  
and unnecessary torque which, in turn, can damage fasteners or other parts  
and accessories, reducing their strength and causing possible failure of the  
fastener or part. A failed or damaged fastener or part may not be able to  
perform as designed, and may lead to an unsafe installation.  
3. Remove the terminal assemblies from the rear of both speakers. The terminal  
assembly is removed by giving it a slight counterclockwise rotation. Use the  
transparent plastic strap to pull the assembly out, as shown.  
1. Secure two corner/wall-mounting  
brackets together by using two  
#10-32 x 1/2" screws provided,  
as shown. Attach the mounting  
bracket to the wall.  
#10-32 x 1/2" Screws (2)  
4. Connect the small end of the multiunit wiring adapter to one of the speaker  
rears, as shown.  
When deciding upon a location for the JBL Control NOW speaker, take care  
NOT to install the mounting bracket closer than 3" (horizontal) and 8-1/2" (vertical)  
to the ceiling. Any closer than the minimum measurements will not allow  
the room needed to position and slide the JBL Control NOW speaker into the  
mounting bracket.  
8-1/2"Minimum  
3"Minimum  
distance from ceiling  
distance from ceiling  
(vertical mount)  
(horizontal mount)  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. The mounting bracket is designed to trap the flange of the JBL Control NOW  
speaker by securing the mounting-bracket cap with two screws through the  
bottom of the mounting bracket. Run the loose end of the multiunit wiring  
adapter through the rear cable-management hole in the mounting bracket,  
and rest the JBL Control NOW speaker’s rear flange in the mounting bracket,  
as shown. This will support the weight of the speaker. Now slide the mounting-  
bracket cap over the assembly. Secure the mounting-bracket cap by  
inserting two #10-32 x 2" screws (provided) in the bottom of the mounting  
bracket and tightening.  
8. Now connect the wires to the terminal assembly.  
IMPORTANT:Make sure all equipment is turned off before making  
any connections. For speaker connections, use a high-quality speaker wire  
with polarity coding. The side of the wire with a ridge or other coding is  
usually considered positive polarity (i.e., +).  
NOTE: If desired, consult your local JBL dealer about speaker wire and  
connection options.  
The speakers have coded terminals that  
accept a variety of wire connectors. The most  
1. Strip 1/4" of wire  
2. Press and push connector  
3. Insert bare end;  
common connection is shown in the diagram  
to the left. To ensure proper polarity, connect  
each + terminal on the back of the amplifier  
or receiver to the respective + (red) terminal  
release push connector  
BLACK = —  
RED = +  
on each speaker, as shown. Connect the  
– (black) terminals in a similar way. See  
the owner’s guides that were included with  
your amplifier, receiver and television to  
confirm connection procedures.  
Mounting-Bracket Cap  
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making  
connections. Doing so will cause poor imaging and diminished bass response.  
Standard  
Connection  
Wiring diagram shows  
polarity connections for  
one channel of a stereo or  
Mounting Bracket  
(side view)  
BLACK = —  
home theater system.  
RED = +  
#10-32 x 2" Screws (2)  
(side view)  
9. To orient the JBL logo into the correct position, pull the JBL logo slightly  
outward from the speaker grille and rotate. The JBL logo is held in place by  
a spring. Peel the adhesive cover off the mounting-bracket covers and  
attach to the top and bottom of the mounting assembly.  
6. Place the large end of the multiunit wiring adapter into the second speaker  
to be installed. Slide the multiunit wiring adapter into the rear of the speaker  
at a slight angle and rotate clockwise.  
Mounting-Bracket  
Covers  
Already connectedto the other speaker.  
7. Connect the terminal assembly to the back of the multiunit wiring adapter.  
It will snap securely into place.  
Mounting-Bracket  
Covers  
Already connectedto the other speaker.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECT AS TWO CHANNELS  
CAUTION  
2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors.  
The customer is responsible for proper selection and use of mounting hardware  
(available through hardware stores), to properly and safely wall-mount the  
speakers. The JBL Control NOW speaker was designed to be easily installed.  
However, if you are unable to clearly and fully understand and follow the  
instructions in this manual, or if you are unsure of your ability to properly install  
these loudspeakers, please contact your dealer or a qualified installer. Please  
do not use any power tools during installation. Power tools can exert excessive  
and unnecessary torque which, in turn, can damage fasteners or other parts  
and accessories, reducing their strength and causing possible failure of the  
fastener or part. A failed or damaged fastener or part may not be able to  
perform as designed, and may lead to an unsafe installation.  
Appropriate  
anchors  
3. Connect the wires to the terminal assembly of each of the JBL Control NOW  
speakers.  
1. Secure two corner/wall-mounting  
brackets together by using two  
#10-32 x 1/2" screws provided,  
as shown. Attach the mounting  
bracket to the wall.  
IMPORTANT:Make sure all equipment is turned off before making  
any connections. For speaker connections, use a high-quality speaker wire  
with polarity coding. The side of the wire with a ridge or other coding is  
usually considered positive polarity (i.e., +).  
#10-32 x 1/2" Screws (2)  
When deciding upon a location for the JBL Control NOW speaker, take care  
NOT to install the mounting bracket closer than 3" (horizontal) and 8-1/2" (vertical)  
to the ceiling. Any closer than the minimum measurements will not allow  
the room needed to position and slide the JBL Control NOW speaker into the  
mounting bracket.  
NOTE: If desired, consult your local JBL dealer about speaker wire and  
connection options.  
The speakers have coded terminals that  
accept a variety of wire connectors. The most  
1. Strip 1/4" of wire  
2. Press and push connector  
3. Insert bare end;  
common connection is shown in the diagram  
to the left. To ensure proper polarity, connect  
each + terminal on the back of the amplifier  
or receiver to the respective + (red) terminal  
release push connector  
BLACK = —  
RED = +  
on each speaker, as shown. Connect the  
– (black) terminals in a similar way. See  
the owner’s guides that were included with  
your amplifier, receiver and television to  
confirm connection procedures.  
8-1/2"Minimum  
3"Minimum  
distance from ceiling  
distance from ceiling  
(vertical mount)  
(horizontal mount)  
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making  
connections. Doing so will cause poor imaging and diminished bass response.  
Standard  
Connection  
Wiring diagram shows  
polarity connections for  
one channel of a stereo or  
BLACK = —  
home theater system.  
RED = +  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. The mounting bracket is designed to trap the flange of the JBL Control NOW  
speaker by securing the mounting bracket cap with two screws through the  
bottom of the mounting bracket. This will support the weight of the speaker.  
Now slide the mounting-bracket cap over the assembly. Secure the mounting-  
bracket cap by inserting two #10-32 x 2" screws (provided) in the bottom of the  
mounting bracket and tightening. Repeat the process with the remaining speaker.  
5. Now rest the second JBL Control NOW speaker’s rear flange in the mounting  
bracket, as shown, and complete the process. Secure the mounting-bracket  
cap with two #10-32 x 2" screws through the bottom of the mounting bracket.  
Mounting-Bracket Cap  
Mounting Bracket  
(side view)  
#10-32 x 2"  
Screws (2)  
#10-32 x 2" Screws (2)  
(side view)  
6. To orient the JBL logo into the correct position, pull the JBL logo slightly  
outward from the speaker grille and rotate. The JBL logo is held in place by  
a spring. Peel the adhesive cover off the mounting-bracket covers and  
attach to the top and bottom of the mounting assembly.  
Mounting-Bracket  
Covers  
#10-32 x 2"  
Screws (2)  
Mounting-Bracket  
Covers  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When deciding upon a location for the JBL Control NOW speaker, take care  
NOT to install the mounting bracket closer than 3" to the ceiling. Any closer than  
3" will not allow the room needed to position and slide the JBL Control NOW  
speaker into the mounting bracket.  
3/4-ROUND WALL-MOUNTING  
Speaker 1  
ceiling  
3" Minimum  
distance from ceiling  
to top of bracket  
(horizontal mounting)  
Speaker 2  
Speaker 3  
2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors.  
CAUTION  
The customer is responsible for proper selection and use of mounting hardware  
(available through hardware stores), to properly and safely wall-mount the  
speakers. The JBL Control NOW speaker was designed to be easily installed.  
However, if you are unable to clearly and fully understand and follow the  
instructions in this manual, or if you are unsure of your ability to properly install  
these loudspeakers, please contact your dealer or a qualified installer. Please  
do not use any power tools during installation. Power tools can exert excessive  
and unnecessary torque which, in turn, can damage fasteners or other parts  
and accessories, reducing their strength and causing possible failure of the  
fastener or part. A failed or damaged fastener or part may not be able to  
perform as designed, and may lead to an unsafe installation.  
Appropriate  
anchors  
1. Secure three corner/wall-mounting brackets together by using four  
#10-32 x 1/2" screws provided as shown.  
3. Remove the terminal assemblies from the rear of all speakers. The terminal  
assembly is removed by giving it a slight counterclockwise rotation. Use the  
transparent plastic strap to pull the assembly out, as shown.  
#10-32 x 1/2" Screws (2)  
#10-32 x 1/2" Screws (2)  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Connect the small end of the multiunit wiring adapter to the rear of  
speaker 1, as shown.  
6. Place the large end of the multiunit wiring adapter that is already connected  
to speaker 1 into speaker 2 by sliding the multiunit wiring adapter into the  
rear of the speaker at a slight angle and rotate clockwise.  
This end is connectedto the first speaker now resting  
in the Corner/Wall-Mount Bracket.  
7. Connect the small end of an additional multiunit wiring adapter to the speaker  
rear as shown.  
5. The mounting bracket is designed to trap the flange of the JBL Control NOW  
speaker by securing the mounting-bracket cap with two screws through the  
bottom of the mounting bracket. Run the loose end of the multiunit wiring  
adapter through the rear cable-management hole in the mounting bracket  
and rest the JBL Control NOW speaker’s rear flange in the mounting bracket,  
as shown. This will support the weight of the speaker. Slide the mounting-  
bracket cap over the assembly. Secure the mounting-bracket cap by inserting  
two #10-32 x 2" screws (provided) in the bottom of the mounting bracket  
and tightening.  
This end is connectedto the first speaker now resting  
in the Corner/Wall-Mount Bracket.  
8. Rest the second JBL Control NOW speaker’s rear flange in the mounting  
bracket, as shown, and complete the process. Secure the mounting bracket  
cap with two #10-32 x 2" screws through the bottom of the mounting bracket.  
#10-32 x 2"  
Screws (2)  
Mounting-Bracket Cap  
#10-32 x 2"  
Screws (2)  
Mounting Bracket  
(side view)  
#10-32 x 2" Screws (2)  
(side view)  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Place the large end of the multiunit wiring adapter that is already installed in  
speaker 2 into speaker 3 by sliding a multiunit wiring adapter into the  
rear of it at a slight angle and rotate clockwise.  
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making  
connections. Doing so will cause poor imaging and diminished bass response.  
Standard  
Connection  
Wiring diagram shows  
polarity connections for  
one channel of a stereo or  
BLACK = —  
home theater system.  
RED = +  
This end is connected to the second speaker currently  
resting in the Corner/Wall-Mount Bracket assembly.  
12. Rest the third JBL Control NOW speaker’s rear flange in the mounting  
bracket as shown and complete the process. Secure the mounting-bracket  
cap with 2 screws through the bottom of the mounting bracket.  
10. Connect the terminal assembly to the back of the second multiunit wiring  
adapter. It will snap securely into place. The other end of the multiunit  
wiring adapter will already be connected to the other speaker already  
mounted in the corner/wall-mount bracket assembly.  
This end is connected to the second speaker currently  
resting in the Corner/Wall-Mount-Bracket Assembly.  
11. Connect the wires to the terminal assembly and place the speaker on  
13. To orient the JBL logo into the correct position, pull the JBL logo slightly  
outward from the speaker grille and rotate. The JBL logo is held in place  
by a spring. Peel the adhesive cover off the mounting-bracket covers and  
attach to top and bottom of mounting-bracket assembly.  
the remaining bracket.  
Speaker 1  
Mounting-Bracket  
Covers  
IMPORTANT:Make sure all equipment is turned off before making  
any connections. For speaker connections, use a high-quality speaker wire  
with polarity coding. The side of the wire with a ridge or other coding is  
usually considered positive polarity (i.e., +).  
Speaker 2  
Speaker 3  
NOTE: If desired, consult your local JBL dealer about speaker wire and  
connection options.  
The speakers have coded terminals that  
accept a variety of wire connectors. The most  
Mounting-Bracket  
Covers  
1. Strip 1/4" of wire  
2. Press and push connector  
3. Insert bare end;  
common connection is shown in the diagram  
to the left. To ensure proper polarity, connect  
each + terminal on the back of the amplifier  
or receiver to the respective + (red) terminal  
release push connector  
BLACK = —  
RED = +  
on each speaker, as shown. Connect the  
– (black) terminals in a similar way. See  
the owner’s guides that were included with  
your amplifier, receiver and television to  
confirm connection procedures.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT:Make sure all equipment is turned off before making  
any connections. For speaker connections, use a high-quality speaker wire  
with polarity coding. The side of the wire with a ridge or other coding is  
usually considered positive polarity (i.e., +).  
STAND-MOUNTING  
IMPORTANT SAFETY NOTE:  
CAUTION  
NOTE: If desired, consult your local JBL dealer about speaker wire and  
The supplied floor stand adapters facilitate installation with a variety of general-  
purpose floor stands available from many manufacturers. Since different stands  
will have different weight capacities and stability characteristics, it is the  
customer’s responsibility to check with the stand manufacturer or dealer to  
ascertain whether that specific stand is capable of handling the weight and  
proportions of these loudspeakers in a safe and stable manner. JBL, Inc.,  
disclaims any liability for the selection of suitable floor stands and/or correct  
compatibility between the selected stand and the supplied stand adapter.  
connection options.  
The speakers have coded terminals that  
accept a variety of wire connectors. The most  
common connection is shown in the diagram  
to the left. To ensure proper polarity, connect  
each + terminal on the back of the amplifier  
or receiver to the respective + (red) terminal  
on each speaker, as shown. Connect the  
– (black) terminals in a similar way. See  
the owner’s guides that were included with  
your amplifier, receiver and television to  
confirm connection procedures.  
1. Strip 1/4" of wire  
2. Press and push connector  
3. Insert bare end;  
release push connector  
BLACK = —  
RED = +  
1. Attach the stand-mounting bracket  
to the stand with the #1/4-20 x 1"  
screw as shown.  
Note trough in Stand-Mount  
2. Run the wiring as shown.  
Bracket for  
cable management.  
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making  
connections. Doing so will cause poor imaging and diminished bass response.  
#1/4-20 x 1"  
Screw Provided  
Standard  
Connection  
Stand-Mount Bracket  
Wiring diagram shows  
polarity connections for  
one channel of a stereo or  
Stand  
BLACK = —  
home theater system.  
RED = +  
3. Place the JBL Control NOW speaker  
on the stand-mount bracket and  
stand, as shown.  
An alternate orientation  
shown here.  
4. Use two #8-32 x 1/2" screws provided  
to secure the JBL Control NOW  
speaker to the stand.  
5. Attach wires.  
#8-32 x 1/2" Screws  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FOUR-SPEAKER ARRAY USING THE OPTIONAL POLE-MOUNT BRACKET (PMB)  
CAUTION  
SPEAKER IDENTIFICATION CHART  
The JBL Control NOW PMB Pole-Mount Bracket facilitates installation of the  
JBL Control NOW and JBL Control NOW AW loudspeakers with a variety of  
general-purpose ceiling-fan-pole assemblies available from many manufacturers.  
Since different fan-pole assemblies will have different weight capacities, pole  
diameters and mounting systems, it is the customer’s responsibility to check  
with the fan-pole-assembly manufacturer or dealer to determine whether that  
specific pole-mount assembly is capable of correctly and securely attaching to  
the PMB and handling the weight and proportions of these loudspeakers in  
a safe and stable manner. JBL, Inc., disclaims any liability for the selection of  
fan-pole assemblies and/or correct compatibility between the selected fan-pole  
assembly and the JBL Control NOW PMB.  
UNPACKING THE BRACKET AND CABLE KIT  
Carefully unpack the bracket and cable assembly. If you suspect damage  
from transit, report it immediately to your dealer and/or delivery service.  
Keep the shipping carton and packing materials for future use. Open the  
package and verify the following contents:  
Included:  
ATTACHING POLE TO POLE-MOUNT BRACKET  
Pole Bushing  
(used for  
smaller-diameter  
drop tubes)  
(FOR LARGER-DIAMETER DROP TUBES)  
1. Run the appropriate wiring down through the drop tube. Slide the drop tube  
through the pole-mount-bracket cap.  
Pole-Mount-Bracket Cap  
Cotter Pin  
Clevis Pin  
Drop Tube  
Pole-Mount Bracket  
(4) #10-32 x 2" Screws  
Pole-Mount-Bracket Cover  
Cable Assembly  
Pole-Mount-Bracket Cap  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2A. Slide the pole-mount bracket up onto the drop tube, aligning the pinholes  
3. Slide the clevis pin through the aligned holes in the pole-mount bracket and  
drop tube. Secure the clevis pin by inserting the cotter pin through the hole  
in the clevis pin.  
on the bracket with those on the drop tube.  
Pole-Mount Bracket Cap  
Pole-Mount-Bracket Cap  
Drop Tube  
Cotter Pin  
Drop Tube  
Pinholes  
Pole-Mount Bracket  
Pole-Mount Bracket  
Clevis Pin  
4. The pole-mount bracket can now hold the weight of the speakers.  
(FOR SMALLER-DIAMETER DROP TUBES)  
2B. When using a smaller drop tube, use the pole bushing when running the  
wiring down through pole-mount-bracket cap. This will help to eliminate  
pole wobble.  
Pole-Mount-Bracket Cap  
Drop Tube  
Clevis Pin  
Pole-Mount Bracket  
Pole Bushing  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPEAKER WIRING  
There are four possible ways of wiring the JBL Control NOW speakers when using the pole-mount kit.  
1. Use the cable assembly provided to wire the units for a single channel.  
Cable Assembly  
2B. Stereo sound distribution – Use this connection for a smaller  
home theater/stereo environment.  
Channel 1  
Channel 2  
A
B
C
B
A
Channel  
1
Channel  
2
Multiunit  
Wiring Adapter  
Multiunit  
Wiring Adapter  
D
Channel  
1
Channel  
Terminal  
Assemblies  
2
C
Single-channel-wiring diagram.  
D
2. Use the multiunit wiring adapters to wire the units for two channels.  
NOTE: There are two options for 2-channel wiring:  
2-Channel-wiring diagram for stereo sound distribution.  
2A. Even sound distribution – Use this connection for even sound distribution  
through both channels. This may be more  
3. Use four sets of cables to wire the units for four channels.  
appropriate for larger rooms.  
Channel 2  
Channel 3  
Channel 2  
Channel 1  
Channel 1  
Channel 4  
A
B
A
B
Channel  
1
Channel  
2
Channel  
1
Channel  
4
Multiunit  
Wiring Adapter  
Multiunit  
Wiring Adapter  
Channel  
2
Channel  
1
C
Channel  
Channel  
3
C
2
D
D
2-Channel-wiring diagram for even sound distribution.  
4-Channel-wiring diagram.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SINGLE-CHANNEL WIRING  
IMPORTANT:Make sure all equipment is turned off before making  
any connections. For speaker connections, use a high-quality speaker wire  
with polarity coding. The side of the wire with a ridge or other coding is  
usually considered positive polarity (i.e., +).  
1. Use the cable assembly provided. Run the cable assembly down the drop  
tube; run the four sets of paired wires out through the wire access holes,  
as shown.  
NOTE: If desired, consult your local JBL dealer about speaker wire and  
NOTE: This procedure is applicable for both large- and small-diameter  
connection options.  
drop tubes. A large-diameter drop tube is shown here.  
The speakers have coded terminals that  
accept a variety of wire connectors. The most  
1. Strip 1/4" of wire  
2. Press and push connector  
3. Insert bare end;  
common connection is shown in the diagram  
to the left. To ensure proper polarity, connect  
each + terminal on the back of the amplifier  
or receiver to the respective + (red) terminal  
release push connector  
BLACK = —  
RED = +  
on each speaker, as shown. Connect the  
– (black) terminals in a similar way. See  
the owner’s guides that were included with  
your amplifier, receiver and television to  
confirm connection procedures.  
Pole-Mount-Bracket Cap  
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making  
Drop Tube  
connections. Doing so will cause poor imaging and diminished bass response.  
Standard  
Connection  
Pole-Mount Bracket  
Wiring diagram shows  
polarity connections for  
one channel of a stereo or  
BLACK = —  
home theater system.  
RED = +  
Wire Access Holes  
Single-channel wiring.  
NOTE: This procedure is applicable for both large- and small-diameter  
drop tubes. A large-diameter drop tube is shown here.  
2. Connect the wires to the terminal assembly of each speaker as shown.  
Place the speaker on the mounting bracket, as shown in step 6 of the mounting-  
bracket-installation procedures. Return to the installation procedures and  
continue.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-CHANNEL WIRING FOR EVEN  
SOUND DISTRIBUTION  
3. Connect the small end of the multiunit wiring adapter to the rear of speakers  
A and B, as shown.  
1. Use the even sound distribution connection for even sound distribution through  
both channels. Run the sets of paired wires out two wire access holes  
through the pole-mount bracket, as shown.  
NOTE: This procedure is applicable for both large- and small-diameter  
drop tubes. A large-diameter drop tube is shown here.  
Pole-Mount-  
Bracket Cap  
4. Place speakers A and B with connectors attached on the pole-mount bracket,  
as shown. Run the wiring for the multiunit wiring adapter through the wire  
access holes, as shown.  
Drop Tube  
A
Drop Tube  
B
Pole-Mount-Bracket Cap  
Pole-Mount  
Bracket  
Connector  
Connector  
Pole-Mount  
Bracket  
Wire Access  
Holes  
Wire Access Holes  
Multiunit Wiring Adapter  
Multiunit Wiring Adapter  
to connect to speaker C  
to connect to speaker D  
2-Channel-wiring for even sound distribution.  
5. Slide the large end of the multiunit wiring adapter that is already attached  
to speaker A into the rear of speaker C at a slight angle and rotate clockwise,  
as shown.  
2. Remove the terminal assemblies from the rear of all speakers. The terminal  
assembly is removed by rotating it slightly counterclockwise, as shown.  
This end is connected to speaker A.  
6. Connect the terminal assembly to the back of the multiunit wiring adapter,  
as shown. It will snap securely into place.  
Use the transparent plastic strap to pull the terminal assembly out, as shown.  
This end is connected to speaker A.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Connect the wires to the terminal assembly and place the speaker on the  
pole-mount bracket. Repeat this process with speaker D. Return to the  
installation procedures and continue.  
IMPORTANT:Make sure all equipment is turned off before making  
any connections. For speaker connections, use a high-quality speaker wire  
with polarity coding. The side of the wire with a ridge or other coding is  
usually considered positive polarity (i.e., +).  
NOTE: If desired, consult your local JBL dealer about speaker wire and  
connection options.  
The speakers have coded terminals that  
accept a variety of wire connectors. The most  
1. Strip 1/4" of wire  
2. Press and push connector  
3. Insert bare end;  
common connection is shown in the diagram  
to the left. To ensure proper polarity, connect  
each + terminal on the back of the amplifier  
or receiver to the respective + (red) terminal  
release push connector  
BLACK = —  
RED = +  
on each speaker, as shown. Connect the  
– (black) terminals in a similar way. See  
the owner’s guides that were included with  
your amplifier, receiver and television to  
confirm connection procedures.  
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making  
connections. Doing so will cause poor imaging and diminished bass response.  
Standard  
Connection  
Wiring diagram shows  
polarity connections for  
one channel of a stereo or  
BLACK = —  
home theater system.  
RED = +  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-CHANNEL STEREO WIRING  
3. Connect the small end of the multiunit wiring adapter to the rear of speakers  
D and B, as shown.  
1. Use the stereo sound-distribution connection for a smaller home theater/stereo  
environment. Run the sets of paired wires out two opposite wire access holes  
through the pole-mount bracket, as shown.  
NOTE: This procedure is applicable for both large- and small-diameter  
drop tubes. A large-diameter drop tube is shown here.  
Pole-Mount-Bracket  
Cap  
4. Place speakers D and B with connectors attached on the pole-mount bracket,  
as shown. Run the wiring for the multiunit wiring adapter through the wire  
access holes, as shown.  
Drop Tube  
Drop Tube  
Multiunit Wiring Adapter  
to connect to speaker A  
Pole-Mount-Bracket Cap  
B
D
Pole-Mount  
Bracket  
Connector  
Multiunit Wiring Adapter  
to connect to speaker C  
Pole-Mount Bracket  
Connector  
Wire Access  
Holes  
Wire Access Holes  
2-Channel-wiring for stereo sound distribution.  
2. Remove the terminal assemblies from the rear of all four speakers. The terminal  
assembly is removed by rotating it slightly counterclockwise, as shown.  
5. Slide the large end of the multiunit wiring adapter that is already attached  
to speaker B into the rear of speaker C at a slight angle and rotate clockwise,  
as shown.  
This end is connected to speaker B.  
Use the transparent plastic strap to pull the terminal assembly out, as shown.  
6. Connect the terminal assembly to the back of the multiunit wiring adapter. It  
will snap securely into place.  
This end is connected to speaker B.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Connect the wires to the terminal assembly and place the speaker on  
the pole-mount bracket. Repeat this process with speaker A. Return to  
the installation procedures and continue.  
4-CHANNEL WIRING  
1. Run the four sets of paired wires out the wire access holes, as shown.  
NOTE: This procedure is applicable for both large- and small-diameter  
drop tubes. A large-diameter drop tube is shown here.  
Pole-Mount-Bracket Cap  
Drop Tube  
IMPORTANT:Make sure all equipment is turned off before making  
any connections. For speaker connections, use a high-quality speaker wire  
with polarity coding. The side of the wire with a ridge or other coding is  
usually considered positive polarity (i.e., +).  
NOTE: If desired, consult your local JBL dealer about speaker wire and  
Pole-Mount Bracket  
connection options.  
The speakers have coded terminals that  
accept a variety of wire connectors. The most  
1. Strip 1/4" of wire  
2. Press and push connector  
3. Insert bare end;  
common connection is shown in the diagram  
to the left. To ensure proper polarity, connect  
each + terminal on the back of the amplifier  
or receiver to the respective + (red) terminal  
release push connector  
BLACK = —  
Wire Access Holes  
RED = +  
4-Channel wiring.  
on each speaker, as shown. Connect the  
– (black) terminals in a similar way. See  
the owner’s guides that were included with  
your amplifier, receiver and television to  
confirm connection procedures.  
2. Connect the wires to the terminal assembly of each speaker, as shown,  
and place the speaker on the mounting bracket, as shown in step 6 of the  
mounting-bracket-installation procedures. Return to the installation  
procedures and continue.  
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making  
connections. Doing so will cause poor imaging and diminished bass response.  
Standard  
Connection  
Wiring diagram shows  
polarity connections for  
one channel of a stereo or  
BLACK = —  
home theater system.  
RED = +  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPEAKER MOUNTING  
After carefully placing all four speakers in the mounting bracket, lightly jostle  
the speakers into place so that the pole-mount-bracket cap will slide down into  
place. Tighten the pole-mount-bracket assembly with the four #10-32 x 2"  
screws provided.  
Drop Tube  
Pole-Mount-Bracket Cap  
Pole-Mount Bracket  
Only two speakers shown here  
for clarity.  
#10-32 x 2"Screws (4)  
Drop Tube  
Place the pole-mount-bracket cover over the bottom visible mounting bracket  
by snapping it into place.  
Pole-Mount Bracket Cap  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE AND SERVICE  
The enclosure may be cleaned using a soft cloth to remove fingerprints or to  
wipe off dust.  
All wiring connections should be inspected and cleaned or remade periodically.  
The frequency of maintenance depends on the metals involved in the connections,  
atmospheric conditions and other factors, but once per year is the minimum.  
If a problem occurs, make sure that all connections are properly made and  
clean. If a problem exists in one loudspeaker, reverse the connection wires to  
the left and right system. If the problem remains in the same speaker, then the  
fault is with the loudspeaker. If the problem appears in the opposite speaker,  
the cause is in another component or cable. In the event that your speaker  
ever needs service, contact your local JBL dealer or distributor or visit  
NOTE: The serial number is located on the rear of the speaker housing.  
To view it, remove the four screws on the rear assembly as shown.  
The product identification  
label is located behind  
the rear housing bracket.  
The serial number is  
located on the back top  
area of the speaker housing  
between the two top rear  
bracket-bolt holes.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
JBL CONTROL NOW™  
JBL CONTROL NOWAW  
Frequency Response (–6dB)  
Max. Recommended Amplifier Power*  
Power Handling (Continuous/Peak)  
Sensitivity (2.83V/1m)  
80Hz – 30kHz  
150W  
50W/300W  
90dB  
Nominal Impedance  
8 Ohms  
Crossover Frequencies  
2000Hz – 18dB/octave; woofer 36dB/octave tweeter;  
Low-Frequency Transducers  
High-Frequency Transducer  
Dual 4" (100mm) PolyPlas, shielded  
3/4" (19mm) Titanium-laminate dome,  
shielded; waveguide  
Weight per Speaker  
6.6 lb (3kg)  
14-5/16" (364mm)  
10-3/8" (262mm)  
9-7/8" (251mm)  
Declaration of Conformity  
5" (127mm)  
We, Harman Consumer Group, Inc.  
2, route de Tours  
72500 Château du Loir  
France  
declare in own responsibility that the products described  
in this owners manual are in compliance with technical  
standards:  
The maximum recommended amplifier power rating will ensure proper system headroom to allow for  
occasional peaks. We do not recommend sustained operation at these maximum power levels.  
*
EN 61000-6-3:2001  
EN 61000-6-1:2001  
Laurent Rault  
Harman Consumer Group, Inc.  
Château du Loir, France 4/08  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features, specifications and appearance are subject to change without notice.  
JBL and Bi-Radial are trademarks of Harman International Industries, Incorporated, registered  
in the United States and/or other countries. JBL Control NOW, PolyPlas and Pro Sound Comes Home  
are trademarks of Harman International Industries, Incorporated.  
PRO SOUND COMES HOME  
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, NY 11797 USA  
8500 Balboa Boulevard, Northridge, CA 91329 USA  
2, route de Tours, 72500 Château du Loir, France  
© 2008 Harman International Industries, Incorporated. All rights reserved.  
Part No. 406-000-05609-E  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Infinity Speaker System TSS 450 User Manual
Ingersoll Rand Septic System 67200 XXX 3id User Manual
Insignia DVD Player NS BDLIVE01 User Manual
Intel Computer Drive SSDSC2CW240A310 User Manual
Jensen Car Speaker JS652 User Manual
JL Audio Car Speaker SB B 5SER 12W6v2 User Manual
Jonsered Cultivator CT2105 R User Manual
Kambrook Electric Heater KCE60 User Manual
Kingsford Charcoal Grill 10040106 User Manual
KitchenAid Garbage Disposal KBDS100T0 User Manual