JBL Portable Speaker 24G AW User Manual

®
JBL® ON AIR  
CONTROL® 2.4G AW (230V)  
OWNER’S GUIDE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY INSTRUCTIONS  
13. Unplug this apparatus during lightning  
storms or when unused for long periods of  
time.  
14. Refer all servicing to qualified service  
personnel. Servicing is required when the  
apparatus has been damaged in any way,  
such as power-supply cord or plug is  
damaged, liquid has been spilled or objects  
have fallen into the apparatus, the  
apparatus has been exposed to rain or  
moisture, does not operate normally, or has  
been dropped.  
15. Do not expose this apparatus to  
dripping or splashing and ensure that no  
objects filled with liquids, such as vases,  
are placed on the apparatus.  
16. To completely disconnect this  
apparatus from the AC Mains, disconnect  
the power supply cord plug from the AC  
receptacle.  
17. The mains plug of the power supply  
cord shall remain readily operable.  
18. Do not expose batteries to excessive  
heat such as sunshine, fire or the like.  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with a dry cloth.  
7. Do not block any ventilation openings.  
Install in accordance with the  
manufacturer’s instructions.  
8. Do not install near any heat sources such  
as radiators, heat registers, stoves or other  
apparatus (including amplifiers) that  
produce heat.  
9. Do not defeat the safety purpose of the  
polarized or grounding-type plug.  
A polarized plug has two blades with one  
wider than the other. A grounding-type plug  
has two blades and a third grounding prong.  
The wide blade or the third prong is  
provided for your safety. If the provided plug  
does not fit into your outlet, consult an  
electrician for replacement of the obsolete  
outlet.  
10. Protect the power cord from being  
walked on or pinched, particularly at plugs,  
convenience receptacles and the point  
where they exit from the apparatus.  
Figure A.  
Example of Antenna Grounding as per  
National ElectricalCode ANSI/NFPA 70  
11. Only use attachments/accessories  
specified by the manufacturer.  
12. Use only with the cart, stand,  
tripod, bracket or table specified  
by the manufacturer or sold with  
the apparatus. When a cart is  
used, use caution when moving the  
cart/apparatus combination to avoid injury  
from tip-over.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
THANK YOU FOR CHOOSING JBL  
For more than 60 years, JBL has been involved in every aspect of  
music and film recording and reproduction, from live performances  
to the recordings you play in your home, car or office.  
1
3
MUTE  
INPUT  
0
2
VOL  
We’re confident that the JBL system you have chosen will provide  
every note of enjoyment that you expected – and that when you think  
about purchasing additional audio equipment for your home, car or  
office, you will once again choose JBL.  
Remote Control  
Please take a moment to register your product on our Web site at  
advance-ments, and helps us to better understand our customers  
and build products that meet their needs and expectations.  
4
5
®
®
The JBL On Air Control 2.4G AW is an advanced wireless  
loudspeaker system that allows you to enjoy your favorite music in  
remote locations around your home, or to add surround speakers to  
your home theater system without running wires to the back of the  
room. To ensure trouble-free performance, please carefully read  
these instructions completely before connecting or using the  
system.  
+
ID  
CODE  
1 2 3 4 TO RIGHT SPEAKER  
UNPACKING THE SYSTEM  
Carefully unpack the system. If you suspect damage from transit,  
report it immediately to your dealer and/or delivery service.  
Keep the shipping carton and packing materials for future use.  
Open the package and verify the following contents:  
DC 20V  
SUB-OUT LINE-IN  
Left/Active Speaker  
(Rear)  
LEFT-CHANNEL SPEAKER  
Included  
1 x Transmitter module  
1 x Power supply for transmitter  
1 x 230V 2-Prong AC power cord for transmitter power supply  
6
8
7
1 x Wall-mount bracket for transmitter with 2 x panhead  
M3 x 4 machine screws for attaching wall-mount bracket  
to transmitter  
4 x Small round self-adhesive feet – to be attached on  
transmitter’s left side panel if transmitter is to be used vertically  
+
1 x Active speaker/receiver (left-channel speaker)  
1 x Power supply for active speaker/receiver  
TO LEFT SPEAKER  
1 x Wall-mount holder for active speaker/receiver universal  
power supply  
1 x Passive speaker (right-channel speaker)  
2 x Terminal covers for active and passive speakers  
6 x M3 x 8 self-tapping screws to attach terminal covers  
Right/Passive  
Speaker  
RIGHT-CHANNEL SPEAKER  
2 x Wall-mount rotatable brackets for active and passive speakers  
(includes bar wrench and backup cords)  
1 x Remote control  
9
1 x Interconnect cable (1m/3.3 ft. RCA – RCA)  
1 x Interconnect cable (1m/3.3 ft. RCA – 3,5mm (1/8-inch) mini plug)  
10m/33 ft. x Speaker wire  
1 x Owner’s manual (multilanguage)  
Wireless Transmitter  
ID  
CODE  
R INPUT L  
1 2 3 4  
A
C
D
B
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
Notes: For the sake of simplicity, throughout this manual we have  
used the term “source” when describing connections and operation.  
This would apply to any device such as an A/V receiver, audio  
component, computer or portable music player.  
Step 2.  
Determine the location of the surround speakers.  
Subwoofer  
The JBL On Air may be connected to your source in several ways.  
First, determine how you would like to use the JBL On Air  
Control 2.4G AW; then follow the setup instructions for that  
application.  
Left Front  
Channel  
Right Front  
Channel  
Center  
Channel  
Application 1  
Adding surround speakers to a home theater system.  
Continue reading the instructions for Application 1 below.  
Application 2  
Adding speakers to remote locations around your home.  
Application 1  
Adding surround speakers to a home theater system:  
Couch  
Determine if your source contains preamp outputs for rear/surround  
channels, usually indicated by RCA-type jacks on the back of the  
receiver labeled as “surround preout” (please refer to your source’s  
owner’s manual to confirm whether it includes the preamp outputs).  
If your receiver includes these outputs, follow the steps below.  
If not, connection is not recommended.  
Left  
Surround  
Channel  
Right  
Surround  
Channel  
Subwoofer  
NOTE: Make sure power is turned off on all components.  
Right Front  
Channel  
Step 1.  
Connect the interconnect cable (included) to the left and right  
surround/rear preamp outputs on the back of your source and the  
Center  
Channel  
D
input on the transmitter module , as shown in Figure 1.  
Right  
Surround  
Channel  
Left Front  
Channel  
Left  
Surround  
Channel  
RECEIVER/PROCESSOR  
Figure 2. Place the active (left) speaker in the recommended  
location for the left surround speaker.  
Surround Channel  
Preamp Outputs  
R
L
ID  
CODE  
R
INPUT  
L
1 2 3 4  
Figure 1.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 3. Connect the speaker wire (included) to the push terminals on  
to or instead of speaker outputs. If your computer does feature  
preamp or line outputs, we recommend that they be used instead of  
speaker outputs.  
5
the active speaker  
and the push terminals on the rear of the  
9
passive speaker  
.
See Figure 3. Please note that the speaker wire supplied features a  
polarity stripe to help distinguish its two conductors. Use this  
polarity stripe to ensure that you are connecting the positive (+)  
terminal on one speaker to the positive (+) terminal on the other, and  
the negative (–) to the negative (–). It does not matter whether you  
use the striped conductor for connecting the positive (+) terminals or  
the negative (–) terminals.  
If you would like to connect the computer to the  
JBL On Air Control 2.4G AW using preamp outputs on your computer,  
follow the steps in Connection A.  
Connection Option A  
Connecting using the preamp outputs on your source:  
Note: Make sure power is turned off on all components.  
Step 1.  
Connect the interconnect cable (included) to the left and right  
front/main preamp outputs or zone 2 outputs or REC outputs and the  
D
inputs on the transmitter module , as shown in Figure 4.  
+
ID  
CODE  
+
1
2
3
4
TO RIGHT SPEAKER  
SOURCE  
TO LEFT SPEAKER  
DC 20V SUB OUT LINE IN  
LEFT CHANNEL SPEAKER  
Front/Main/Second Room  
Preamp Outputs  
RIGHT CHANNEL SPEAKER  
R
L
Figure 3.  
B
Step 4. Plug the transmitter module and active speaker  
6
into  
the wall outlet, using the correct power supply and power cord.  
A
Make sure the transmitter’s antenna  
is extended upwards.  
Step 5. If necessary, configure your source to activate the preamp  
level outputs for the surround/rear channels (consult your source’s  
owner’s manual for specific instructions).  
ID  
CODE  
R INPUT L  
1 2 3 4  
C
Make sure the ID code setting on the transmitter  
is set to the  
4
same setting as that on the active speaker . See Page 8 of this  
manual for more information on ID codes. When connected properly,  
the top LED on the front of the active speaker should be green. When  
first plugged in, it will sometimes take several seconds for the  
Control 2.4G AW active speaker to initialize and “wake up.“ Until  
then, the top LED will be in red. Once the top LED is green, the  
bottom LED should flash green until the transmitter and active  
speaker “lock in.” It will then also illuminate in solid green. This LED  
will light in orange if the local input on the active speaker is selected  
(see Page 8 under Local Input for more details).  
Figure 4.  
Step 2. Place the active speaker in the desired location in your home  
near an AC outlet, as it needs to plug in to the wall.  
Step 3. Connect the speaker wire (included) to the push terminals on  
5
9
the active speaker  
and the push terminals on the rear of the  
passive speaker , as shown in Figure 3. Please note that the  
speaker wire supplied features a polarity stripe to help distinguish its  
two conductors. Use this polarity stripe to ensure that you are  
connecting the positive (+) terminal on one speaker to the positive  
(+) terminal on the other, and the negative (–) to the negative (–).  
It does not matter whether you use the striped conductor for  
connecting the positive (+) terminals or the negative (–) terminals.  
Application 2  
Adding speakers to remote locations around your home:  
Audio sources that can be used in this application may be an A/V  
receiver or audio receiver, a portable audio player, or a computer  
featuring a sound card. First, determine whether your source  
contains RCA-type preamp outputs for the front/main channels or a  
3,5mm (1/8-inch) stereo single-pin output. On an A/V or audio  
receiver, the preamp outputs are usually indicated by RCA-type  
jacks on the back of the receiver labeled as “pre-out” (please refer  
to your source’s owner’s manual to confirm whether it includes  
preamp outputs). If your source includes these RCA-type outputs,  
follow the steps in Connection Option A.  
If your source features a 3,5 mm (1/8-inch) single-pin stereo jack,  
follow steps in Connection Option B. If your receiver does not  
feature either type of preamp outputs for the front/main channels, it  
cannot be used with Control 2.4G AW. Some computer sound cards  
feature more than one 3,5 mm(1/8-inch) single-pin jack. There is  
almost always one output that is called a speaker output. However,  
some sound cards feature a preamp output or line output in addition  
B
Step 4. Plug the transmitter module and active speaker  
the wall outlet. Make sure the transmitter’s antenna  
upward.  
6
into  
A
is extended  
C
Step 5. Make sure the ID code setting on the transmitter  
is set to  
4
the same setting as that on the active speaker . See Page 8 of this  
manual for more information on ID codes. If necessary, configure  
your receiver to activate the preamp level outputs for the main/front  
channels (consult your source’s owner’s manual for specific  
instructions).  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
Step 4. Plug the transmitter module and active speaker  
6
When connected properly, the top LED on the front of the active  
speaker should be green. When first plugged in, it will sometimes  
take several seconds for the Control 2.4G AW active speaker to  
initialize and “wake up.” Until then, the top LED will be in red. Once  
the top LED is green, the bottom LED should flash green until the  
transmitter and active speaker “lock in.” It will then also light in solid  
green. This LED will light in orange if the local input on the active  
speaker is selected (see Page 8 under Local Input for more details).  
into  
the wall outlet, using the correct power supply and power cord.  
A
Make sure the transmitter’s antenna  
is extended upward.  
C
Make sure the ID code setting on the transmitter  
is set to the  
4
same setting as that on the active speaker . See Page 8 of this  
manual for more information on ID codes. When connected properly,  
the top LED on the front of the active speaker should be green.  
When first plugged in, it will sometimes take several seconds for the  
Control 2.4G AW active speaker to initialize and “wake up”. Until  
then the top LED will be in red. Once the top LED is green, the bottom  
LED should flash green until the transmitter and active speaker “lock  
in”. It will then also light in solid green. This LED will light in orange if  
the local input on the active speaker is selected (see Page 8 under  
Local Input for more details).  
Connection Option B  
Connecting using the 3,5mm(1/8-inch) single-pin stereo jack on  
your source:  
Note: Make sure power is turned off on all components.  
Step 1. Connect the RCA – mini-jack cable (included) to the preamp  
If you are installing the speakers outdoors, please attach the  
provided terminal cover to each speaker, using three M3 x 8 self-  
tapping screws provided.  
out, line out or headphone 3,5mm (1/8-inch) output of your portable  
D
audio player and the inputs on the transmitter module , as shown  
in Figure 5.  
Portable Audio Device or  
Computer Headphone Jack (3,5mm(1/8")) Mini  
ID  
CODE  
R
INPUT  
L
1 2 3 4  
Figure 5.  
Step 2. Place the active speaker in the desired location in your home  
near an AC outlet, as it needs to plug into the wall.  
Step 3. Connect the speaker wire (included) to the push terminals on  
5
9
the active speaker  
and the push terminals on the rear of the  
passive speaker , as shown in Figure 3. Please note that the  
speaker wire supplied features a polarity stripe to help distinguish  
its two conductors. Use this polarity stripe to ensure that you are  
connecting the positive (+) terminal on one speaker to the positive  
(+) terminal on the other, and the negative (–) to the negative (–).  
It does not matter whether you use the striped conductor for  
connecting the positive (+) terminals or the negative (–) terminals.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
Adjusting the Volume  
ID Code  
In the unlikely event that you experience interference when  
operating the system, or if you have more than one set of Control  
2.4G AW transmitters and receivers in operation, you may change  
the channel in which the system operates. On the transmitter module  
and the active speaker, there is a four-position “ID Code” selector.  
Simply set the selectors to one of the other positions. The transmitter  
and active speaker must be set to the same position in order for the  
system to function correctly. You can also set up a maximum of two  
pairs of speakers to be receiving from the same transmitter by  
setting the channel selector on the transmitter and both of the active  
speakers to the same channel. Please note that the two active  
speakers need to be at least 10m (33 feet) apart, or reception and  
operating range in one or both units may be degraded.  
Application 1  
Adding surround speakers to a home theater system:  
In this application, the output level of your Control 2.4G AW active  
speakers will not only be dependent on the volume setting of your  
A/V source, it will also need to be properly adjusted after installation  
and before use in order to be able to work correctly with the other  
speakers in your multichannel surround system. To adjust the output  
level, turn you A/V source on, set your A/V source’s volume control  
about a third of the way up, and activate the speaker-level-  
adjustment test tone. Make sure that the Control 2.4G AW  
transmitter and speakers are on, both of its speakers are connected,  
and there is RF lock (i.e., lower LED on active speaker is solid green).  
1
2
Using the Control 2.4G AW remote control  
and  
adjust the  
Auto On/Standby  
volume level of Control 2.4G AW until its output level is balanced with  
the rest of the speakers in your surround system. From this point on,  
you will not be using the remote control of your Control 2.4G AW for  
volume settings. You will be increasing and decreasing the output  
level for the entire surround sound system using your A/V source’s  
volume control. Please note that Control 2.4G AW will retain its  
volume setting when it is in standby, so there is no need to set its  
volume level every time the system is turned on.  
The JBL Control 2.4G AW will automatically enter the Standby mode  
after approximately 10 minutes when no signal is detected from your  
system. The JBL Control 2.4G AW will then power ON instantly when  
a signal is detected.When Mute 0is engaged, auto turn-off is  
deactivated.  
Indicator Light Information  
Power Indicator LED  
(Top)  
Input LED  
(Bottom)  
Application 2  
Adding speakers to remote locations around your home:  
Green  
System is on  
Transmitter and speaker are  
communicating (RF lock)  
Blinking Green Receiving IR command  
Transmitter and speaker are  
not communicating (no RF lock)  
Depending on the type of connection and the specific source that  
you are using, the volume setting on your receiver may affect the  
sound output level of your Control 2.4G AW. To check whether the  
output from your source is volume-dependent, turn the volume level  
on your receiver to approximately half-way. Turn on your Control  
2.4G AW transmitter and active speaker. Once the lower LED on the  
active speaker lights in solid green, indicating that RF lock has been  
achieved, verify that there is sound output from the active speaker.  
Then increase and decrease the volume control on your receiver  
and observe whether this affects the sound output from your active  
speakers. If it does not, then the volume control on your source unit  
can be set at any position that you may desire as it does not affect  
the performance of Control 2.4G AW. If changing the volume setting  
on your source does affect the output from Control 2.4G AW, then  
you will need to always keep your source’s volume control at about  
half-way up with audio receivers or A/V receivers, at about three-  
quarters of the way up when using a computer, and at maximum if  
using a portable audio device. From this point on, you will use the  
remote control included with the JBL On Air Control 2.4G AW  
from remote control  
Red  
Standby  
(no signal being received)  
Orange  
Local input is selected  
Subwoofer Output  
The JBL On Air Control 2.4G AW wireless speaker system includes a  
7
subwoofer output  
on the rear of the active speaker. This output  
allows you to feed the low-frequency sounds to a separate powered  
subwoofer. A powered subwoofer will deliver deeper bass response  
than is possible with speakers alone.  
To connect a powered subwoofer to the active speaker, simply  
7
connect the subout  
on the active speaker to the line-in on the  
rear of the powered subwoofer using a 3,5mm (1/8-inch) stereo mini-  
jack – dual-RCA cable (not included*). Please note that this output is  
full range and not filtered or low-passed. Make sure that your  
powered subwoofer features a low-pass crossover network and that  
this crossover is indeed selected. Do not use the LFE input on a  
powered subwoofer as it is not filtered and you will be hearing a lot  
of undesirable higher frequency information from your subwoofer.  
* Only one stereo mini-jack/dual RCA cable is included with the  
system. If you are following Application 2, Connection Option B, you  
will need to purchase this cable.  
1
2
wireless speaker system to adjust the volume  
and  
.
Local Input  
The JBL On Air Control 2.4G AW wireless speaker system also  
8
includes a local input  
on the rear of the active speaker. This input  
allows you to hook up a portable audio player directly to the speaker  
wherever you may happen to be. For example, you could have the  
system connected to your receiver as described in Application 2,  
listening to a local FM station and then hook up your portable music  
player to the local input and switch between the two different  
sources.  
A Word About Wireless Products  
The JBL On Air Control 2.4G AW wireless speaker system utilizes  
advanced wireless transceivers operating in the 2.4GHz frequency  
band. This is the same frequency band that is used for wireless  
home networks and high-quality cordless phones. It also allows for  
the transmission of high-performance, full-spectrum sound to  
remote locations, wirelessly.  
Like all wireless devices, the JBL On Air Control 2.4G AW wireless  
speaker’s operating range may vary depending upon variables such  
as building construction methods and materials, atmospheric  
conditions and other sources of interference. Please consult your  
information or assistance.  
To connect portable audio player to the active speaker, simply  
connect the preamp out, line out or headphone jack to the line-in  
8
on the rear of the active speaker using a 3,5mm (1/8-inch) mini-jack –  
3,5 mm (1/8-inch) mini-jack cable (not included).  
3
To switch between the two sources, push the input button  
remote control.  
on the  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
WALL AND STAND PLACEMENT  
Adjustable wall brackets are included for the two speakers and  
transmitter module. The included bracket are for wall-mounting only.  
It is not to be used for ceiling mounting. Ceiling mounting of the  
Control 2.4G AW transmitter and/or speakers is not recommended,  
regardless of bracket used.  
A. Loosen and remove the molded nut (2) by turning it counter  
clockwise. Use the supplied metal bar (5) if necessary by inserting  
it in one of the holes on the molded nut (2).  
B. Pull the ball/shaft (3) out of the wall bracket (4).  
Wall-Mounting the Speakers  
Using Wall Brackets Provided  
C. Slide on the molded nut (2) onto the ball/shaft (3) with threaded  
opening facing the ball, and thread on the metal nut (1) all the way  
onto the ball/shaft (3), with the nut’s (1) ”knurled” surface facing  
away from the ball.  
Important safety note: Proper selection of mounting hardware not  
included herein, and proper assembly and installation of brackets,  
including, but not limited to, selection of appropriate weight-bearing  
support and bracket use with the specified speaker only is the  
exclusive responsibility of the customer. Manufacturer disclaims any  
liability for the selection of mounting hardware and/or bracket  
installation.  
D. Screw on the ball/shaft (3) into the threaded 1/4"-20 insert on the  
back of the speaker cabinet (6) until it is fully seated against the  
bottom of the insert. Back out the ball-shaft assembly 1/2 of a turn  
and tighten the nut against the speaker. If the ball and shaft  
assembly is not backed out before tightening the nut, performing  
Step G below may dislodge the threaded insert in the speaker  
housing and permanently damage the speaker.  
E. Tighten the ”knurled” nut (1) using a crescent wrench until it is  
firmly seated against the back of the speaker and has fully locked  
the ball/shaft (3) and the speaker cabinet together. Pleace note  
that once this nut is tightened, it may embed some marks on the  
back of the speaker where the attachment is made. However,  
these marks will be covered by the nut (1).  
F. The back-up cord (8) is provided as an additional measure to  
prevent the fall of the speaker in case the speaker becomes  
detached from the wall bracket.  
One of the two lower screws (9) that attach the wall bracket (4) to  
the wall will need to go through the eyelet (11) at the end of the cord  
before going through the wall bracket hole. Mount the wall bracket  
(4) onto a wood stud on the wall, using #10, minimum 1-inch-long,  
panhead wood screws. Make sure that all 4 screws are driven into  
the stud, not drywall. If the bracket needs to be mounted on  
drywall, the use of properly selected and installed wall-anchors  
and screws is essential. Make sure that the screw head is at least  
9mm (0.36 or approximately 3/8 of an inch) or larger in diameter so  
that it can properly hold the backup cord eyelet (11).  
G. Holding the speaker cabinet (7) with both hands, reinsert the ball  
portion of the ball/shaft (3) into the wall bracket (4).  
H. Hand-tighten the molded nut (2) while positioning the speaker for  
the intended orientation.  
I. Once the orientation of the speaker is finalized, use the metal bar  
(5) in one of the holes on the molded nut (2) and tighten securely.  
J. Securely attach the other end (10) of the backup cord (8) to the  
Control 2.4G, by engaging it through the bar (12) on the back  
speaker.  
Exploded  
Also included with the system is a wall-mount holder for the active  
speaker’s power supply. If desired, you may attach this holder to the  
wall and insert the speaker’s power supply.  
+
+
Please note that while the Control 2.4G AW is an all-weather outdoor  
loud-speaker, it is not waterproof. Neither the speakers nor power  
supply should be submerged or directly exposed to water, ice, snow  
or sustained moisture.Do not install the transmitter module outdoors.  
TO LEFT SPEAKER  
TO LEFT SPEAKER  
CORRECT  
INCORRECT  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wall-Mounting the Speakers Using  
Third-Party Wall Brackets  
Each JBL On Air Control 2.4G AW wireless speaker contains a  
1/4"-20 threaded insert on the back to facilitate the use of third-party  
wall brackets. Please consult your JBL dealer or distributor for  
recommendations.  
Remote Control Battery Replacement  
CAUTION:  
When replacing the lithium battery in the remote, make sure that the  
replacement battery is inserted in correct polarity. Place the battery so that  
its positive (+) side faces up with the tray held so that the surface with the  
dot is facing up.  
Remote-control-battery installation  
NOTES: Customer is responsible for proper selection and  
installation of appropriate third-party wall brackets.  
The threaded insert on the bottom of the speaker is not intended for  
wall-bracket attachment. It is provided for use with an appropriate  
third-party floorstand.  
Pull battery  
drawer out.  
Insert new battery  
with “+” side up, and  
slide battery drawer  
back into remote.  
Push small tab  
Stand-Mounting the Speakers  
Each JBL On Air Control 2.4G AW wireless speaker contains a  
1/4"-20 threaded insert on the bottom to facilitate the use of third-  
party floor stands. Please consult your JBL dealer for  
recommendations.  
toward battery slot.  
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY  
REPLACED.  
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE (CR2032).  
NOTE: Customer is responsible for proper selection and installation  
of appropriate third-party wall brackets and/or floor stands.  
WARNING: DO NOT EXPOSE BATTERIES TO EXCESSIVE HEAT SUCH AS  
DIRECT SUNLIGHT, FIRE OR THE LIKE.  
Wall-Mounting the Transmitter Module  
Step 1. Insert the two M3 x 4 machine screws through the wall  
bracket and into the rear of the transmitter module, as shown in  
Figure 6.  
Dispose of dead batteries in accordance with local regulations.  
MAINTENANCE AND SERVICE  
The speaker and transmitter enclosures may be cleaned using a soft  
cloth to remove fingerprints or to wipe off dust.  
All wiring connections should be inspected and cleaned or remade  
periodically. The frequency of maintenance depends on the metals  
involved in the connections, atmospheric conditions and other  
factors, but once per year is the minimum.  
In the event that your system ever needs service, contact your local  
near you.  
Figure 6.  
Step 2. Attach the transmitter module with wall bracket to the wall  
using suitable hardware, and wall anchors if necessary.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
Frequency Range ( 3dB):  
Amplifier Output:  
80Hz – 20kHz  
15 Watts per channel  
Low-Frequency Driver:  
High-Frequency Driver:  
Operating Range:  
100mm (4") Magnetically shielded  
12mm (1/2") Titanium-laminate, magnetically shielded  
Up to 21m (70') depending upon conditions  
2.4GHz  
RF Operating Frequency:  
Dimensions  
Speaker (H x W x D):  
229mm x 156mm x 140mm  
(9" x 6-1/8" x 5-1/2")  
Transmitter (H x W x D):  
29mm x 124mm x 98mm  
(1-1/8" x 4-7/8" x 3-7/8")  
95mm (3-3/4") High with antenna extended  
Weight  
Active Speaker:  
Passive Speaker:  
Transmitter:  
2.1kg (4.6 lb)  
2.0kg (4.3 lb)  
0.2kg (0.5 lb)  
Features, specifications and appearance are subject to change without notice.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
JBL and Control Series are trademarks of Harman International Industries, Incorporated,  
registered in the United States and/or other countries. Pro Sound Comes Home are trademark  
of Harman International Industries, Incorporated.  
PRO SOUND COMES HOME  
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, NY 11797, USA  
8500 Balboa Boulevard, Northridge, CA 91329, USA  
2, route de Tours, 72500 Château du Loir, France  
516.255.4JBL (4525) (USA only) www.jbl.com  
© 2008 Harman International Industries, Incorporated. All rights reserved.  
Part No. 406-000-05942-E  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Infinite Peripherals Barcode Reader PRO 4 User Manual
Jacuzzi Hot Tub Alexa User Manual
Jet Tools Saw COS18L User Manual
JL Audio Car Speaker 94460 User Manual
JVC CD Player KD AHD59 User Manual
Kaser MP3 Player BW User Manual
Keys Fitness Bicycle AB920R User Manual
Kodak Digital Camera C875 User Manual
Konica Minolta Printer 5430 DL 5440 DL 5450 User Manual
Kramer Electronics Stereo Receiver COBRA R500 2 User Manual