®
HOME THEATER
IN-WALL SERIES
HTI6, HTI8, HTI55 and
HTI6C
OWNER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER PLACEMENT
FRONT SPEAKERS (HTI6, HTI8, HTI55)
400 – 600
MODELS HTI6, HTI8 AND HTI55 AS REAR SPEAKERS
5 – 6 ft.
WALL
WALL
WALL
WALL
MODEL HTI6C IN CEILING
be placed at about the same
and, ideally, should face each
other and be at a level higher
than the listeners’ ears. If that
is not possible, they may be
placed in a wall behind the lis-
tening position, facing forward.
The rear wall is the required
mounting position for the sur-
round back speakers in 6.1- and
7.1-channel system. The sur-
round speakers should not call
attention to themselves. They
should provide a diffuse, ambi-
ent sound accompanying the
main program material heard in
the front speakers. In Dolby*
height from the floor as the
listeners’ ears will be, with the
tweeters aimed toward the
listening position at ear-level
height.
Model HTI55 is suitable for the
front left, center and right posi-
tions, and it may also be used
as a side surround or surround
back speaker. It may be
mounted horizontally or verti-
cally, but make sure to position
it so that the tweeters for all of
the front speakers are at the
same height (or differ by no
more than 2 feet). You may
rotate the tweeter to correctly
orient the JBL logo.
Proper placement of the
speakers is an important step
in obtaining the most realistic
soundstage possible. These
recommendations are for the
optimum placement of the loud-
speakers. Use these placement
recommendations as a guide.
Slight variations will not dimin-
ish your listening pleasure.
®
Digital and DTS systems, aim
the tweeters toward the listen-
ing position at ear-level height.
In a home theater configura-
tion, the two surround speakers
should be placed slightly
The front speakers should be
placed the same distance from
each other as they are from the
listening position. They should
behind the listening position
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER CONNECTIONS
CONNECTION TIPS
The wires for both speakers
should be the same length. If
one speaker is placed closer to
the amplifier than the other,
hide the excess wire behind the
wall.
Speakers and electronics
terminals have corresponding
(+) and (–) terminals. Most
manufacturers of speakers and
electronics, including JBL, use
red to denote the (+) terminal
and black for the (–) terminal.
It is important to connect both
speakers identically: (+) on the
speaker to (+) on the amplifier
and (–) on the speaker to (–)
on the amplifier. Wiring “out
of phase” results in thin sound,
weak bass and a poor stereo
image. With the advent of multi-
channel surround-sound
LEFT
RIGHT
systems, connecting all of
the speakers in your system
with the correct polarity
remains equally important in
order to preserve the proper
ambience and directionality
of the program material.
LEFT
RIGHT
Front or Rear Speaker Outputs
WIRE LENGTH
Up to 20 ft.
RECOMMENDED SIZE
16 gauge
12 gauge
10 gauge
Up to 30 ft.
Greater than 30 ft.
INSTALLATION
The JBL HTI Series in-wall
speakers were designed to be
easily installed. However, if you
are unsure of your ability to
properly install these loud-
speakers, please contact your
dealer or a qualified installer.
Tools Needed
Pencil
Phillips #2 screwdriver
Utility knife
Measuring tape
Carpenter’s level
Awl
4
Download from Www.Somanuals.com. All Manuals Search And Download.
EXISTING CONSTRUCTION
HTI6, HTI8, HTI55
Level
≥1/2"
≥1/2"
≥1/2"
Template
Remove the grille from the
speaker frame by pulling on the
paper tab. If the tab is missing,
to avoid scratching the grille or
baffle you may unfold a paper
clip, insert the straight end
through one of the holes in the
grille, and gently pull up.
Determine the correct speaker
location.
Note: Always allow at least
one-half inch between a wall
stud and the speaker cutout or
the locking tabs will not be able
to swivel into place.
Note: Remove the inner tem-
plate, which is the paint shield,
at the perforation. Use the
outer template when cutting
the drywall. Although the HTI55
may be oriented either horizon-
tally or vertically, the installa-
tion procedure is the same.
Place the frame assembly in
the wall.
Cut the drywall.
Connect the speaker wires to
the speaker.
The HTI speakers feature
unique swivel mounts for the
tweeters that enable you to aim
the very directional high fre-
quencies toward the
listening position, at ear-level
height. Before installing the
speaker grille, gently press on
the outer edge of the tweeter
mount to adjust the position of
the tweeter. The tweeter will
not swivel more than 15
degrees in any direction; do not
attempt to force it to move fur-
ther. You may also rotate the
tweeter to orient the JBL logo
as desired.
Replace the metal grille. For the
HTI55 only, attach the JBL logo
to the grille to correspond to
vertical or horizontal installa-
tion.
Screw down each of the four
(six for HTI55) Phillips head
screws. The locking tabs will
swivel into place and secure
the unit to the rear surface of
the drywall.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
EXISTING CONSTRUCTION
HTI6C
≥1/2"
≥1/2"
≥1/2"
Remove the grille from the
speaker frame by pulling on the
paper tab. If the tab is missing,
to avoid scratching the grille or
baffle you may unfold a paper
clip, insert the straight end
through one of the holes in the
grille, and gently pull up.
Determine the correct speaker
location.
Note: Remove the inner tem-
plate, which is the paint shield,
at the perforation. Use the
outer template when cutting
the drywall.
Cut the drywall.
Note: Always allow at least
one-half inch between a wall
stud and the speaker cutout or
the locking tabs will not be able
to swivel into place.
Connect the speaker wires to
the speaker.
Place the frame assembly in
the wall.
Screw down each of the three
Phillips head screws. The lock-
ing tabs will swivel into place
and secure the unit to the rear
surface of the drywall.
The HTI speakers feature
unique swivel mounts for the
tweeters that enable you to aim
the very directional high
frequencies toward the
listening position, at ear-level
height. Before installing the
speaker grille, gently press on
the outer edge of the tweeter
mount to adjust the position of
the tweeter.
Replace the metal grille.
The tweeter will not swivel
more than 15 degrees in any
direction; do not attempt to
force it to move further. You
may also rotate the tweeter to
orient the JBL logo as desired.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
NEW CONSTRUCTION
You will need to purchase the correct rough-in frame kit for your model:
Speaker Model
Rough-in Frame Kit
HTI6
HTI8
RIF6
RIF8
HTI55
HTI6C
RIF55
RIF6C
Detailed installation instructions are supplied with the rough-in kit.
PAINTING THE SPEAKER
FRAME AND GRILLE
JBL HTI Series loudspeakers
can be painted to match any
decor. If you wish to change
their color, the satin finish on
the grille and frame will func-
tion as a primer coat. Before
painting, install the paint shield
(in the assembly kit) securely
into the recess in the baffle.
This will protect the speaker
components and baffle from
paint residue.
Use a high-quality spray paint,
and apply a thin coat of color.
Note: Gently remove the
acoustical foam blanket from
the grille before painting. Reat-
tach the blanket after the paint
has dried.
Be certain the grille per-
forations remain free of paint.
Filling them with paint will
diminish the sound quality.
TROUBLESHOOTING
IF THERE IS NO SOUND
FROM ANY OF THE
SPEAKERS:
In multichannel applications,
See your receiver/processor’s
owner’s manual for futher infor-
mation on correct speaker con-
figuration in Dolby Digital, DTS
and other surround-sound
modes.
make sure that your receiver or
processor has been configured
to enable all channels that you
are using.
• Check that receiver/amplifier
is on and a source is playing.
• Check all wires and connec-
tions between receiver/ampli-
fier and speakers. Make sure
all wires are connected. Make
sure none of the speaker wires
are frayed, cut or punctured.
IF THERE IS LOW (OR
NO) BASS OUTPUT:
IF THE SYSTEM PLAYS
AT LOW VOLUMES BUT
SHUTS OFF AS VOLUME
IS INCREASED:
• Make sure the connections
to the left and right “Speaker
Inputs” have the correct polar-
ity (+ and –).
• Check all wires and connec-
tions between receiver/ampli-
fier and speakers. Make sure
all wires are connected. Make
sure none of the speaker wires
are frayed, cut or punctured.
• Review proper operation of
your receiver/amplifier.
• Consider adding a powered
subwoofer to your system.
IF THERE IS NO SOUND
COMING FROM ONE
SPEAKER:
• In Dolby Digital or DTS modes,
make sure your
receiver/processor is correctly
configured. When using a sub-
woofer, make sure the sub-
woofer output of the receiver/
processor has been enabled. If
no subwoofer is being used,
make sure the left and right
front and rear speakers have
been config-ured as “LARGE.”
• If more than one pair of main
speakers is being used, check
the minimum-impedance
requirements of your receiver/
amplifier.
• Check the “Balance” control
on your receiver/amplifier.
• Check all wires and connec-
tions between receiver/ampli-
fier and speakers. Make sure
all wires are connected. Make
sure none of the speaker wires
are frayed, cut or punctured.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
HTI6
HTI8
HTI55
HTI6C
Frequency Response
38Hz – 20kHz (–10dB)
Frequency Response
30Hz – 20kHz (–10dB)
Frequency Response
40Hz – 20kHz (–10dB)
Frequency Response
40Hz – 20kHz (–10dB)
Recommended Maximum
Amplifier Power
Recommended Maximum
Amplifier Power
Recommended Maximum
Amplifier Power
Recommended Maximum
Amplifier Power
†
†
†
†
100 watts
120 watts
120 watts
100 watts
Impedance
8 ohms nominal
Sensitivity
88dB (2.83V/1m)
Impedance
8 ohms nominal
Sensitivity
90dB (2.83V/1m)
Impedance
8 ohms nominal
Sensitivity
88dB (2.83V/1m)
Impedance
8 ohms nominal
Sensitivity
88dB (2.83V/1m)
Crossover Frequency
Crossover Frequency
Crossover Frequency
Crossover Frequency
2,500Hz
Woofer
2,500Hz
Woofer
2,000Hz
Woofer
2,000Hz
Woofer
6-1/2" Polymer-coated aluminum
8" Polymer-coated aluminum
Dual 5" polymer-coated aluminum
6-1/2" Polymer-coated aluminum
cone w/rubber surround
cone w/rubber surround
cone w/rubber surround
cone w/rubber surround
Tweeter
Tweeter
Tweeter
Tweeter
1" Pure-titanium dome,
1" Pure-titanium dome,
1" Pure-titanium dome,
1" Pure-titanium dome,
w/Elliptical Oblate Spheroidal™
(EOS) waveguide, and swivel mount
w/Elliptical Oblate Spheroidal™
(EOS) waveguide, and swivel mount
w/Elliptical Oblate Spheroidal™
(EOS) waveguide, and swivel mount
w/swivel mount
Plate Size (Diameter)
Plate Size (W x H)
216 x 279mm (8-1/2" x 11")
Mounting Cutout Size (W x H)
181 x 246mm (7-1/8" x 9-11/16")
Mounting Depth
98mm (3-7/8")
Plate Size (W x H)
257 x 333mm (10-1/8" x 13-1/8")
Mounting Cutout Size (W x H)
225 x 300mm (8-7/8" x 11-13/16")
Mounting Depth
102mm (4")
Weight per Speaker
6.1kg (13.5 lb)
Plate Size
233mm (9-3/16")
Mounting Cutout Size
(Diameter)
200mm (7-7/8")
Mounting Depth
108mm (4-1/4")
Weight per Speaker
4.5kg (10 lb)
391 x 191mm (15-3/8" x 7-1/2")
Mounting Cutout Size
56 x 152mm (14" x 6"3)
Mounting Depth
98mm (3-7/8")
Weight per Speaker
2.6kg (5.7 lb)
Weight per Speaker
5kg (11 lb)
Declaration of Conformity
All features and specifications are subject to
change without notice.
† The maximum recommended amplifier power
rating will ensure proper system headroom to
allow for occasional peaks. We do not recom-
mend sustained operation at these maximum
power levels.
We, Harman Consumer Group International
2, route de Tours
72500 Chateau-du-Loir
France
declare in own responsibility that the products described in this
owner’s manual are in compliance with technical standards:
* Dolby is a trademark of Dolby Laboratories.
EN 61000-6-3:2001
EN 61000-6-1:2001
DTS is a registered trademark of
Digital Theater Systems, Inc.
Gary Mardell
Harman Consumer Group International
Chateau-du-Loir, France 9/04
PRO SOUND
OWNER’S GUIDE
COMES HOME™
PRODUCT LINE:
JBL Home Theater In-Wall Series
JBL Consumer Products
250 Crossways Park Drive, Woodbury, NY 11797
Europe: 2. Route de Tours, 72500 Château du Loir, France
MODELS:
HTI6, HTI8, HTI55 and HTI6C
DESIGN GOAL:
Combine the superior performance of traditional
NOTE: For new-construction applications, be sure
to purchase the correct rough-in frame kit.
JBL loudspeakers with the convenience of in-wall installation.
™
TWEETER TYPE: Pure-titanium dome with EOS waveguide,
and swivel mount
© 2004 Harman International Industries, Incorporated
JBL is a registered trademark of Harman International
Industries, Incorporated.
WOOFER TYPE: Polymer-coated aluminum cone with rubber surround
™
CROSSOVER NETWORK:Straight-Line Signal Path (SSP)
Part No.406-000-05033
PROFESSIONAL REFERENCE:Studio Monitor
Download from Www.Somanuals.com. All Manuals Search And Download.
|