c o m p o n e n t
s y s t e m s
o w n e r ’s
m a n u a l
T H A N K Y O U
for purchasing a JBL Power Series®
automotive loudspeaker component
system. We’ve organized this manual
to make your installation as simple and
trouble-free as possible. Please read it
thoroughly before proceeding. Remember
to keep your sales receipt and this manual in a
safe place so both are available for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IN S TA LLA T IO N
C O N N E C T IO N S
Figure 5. Mounting the tweeter using
the I-Mount flush-mounting kit.
Open the crossover housing by firmly squeezing the sides
of the top half and lifting it away from the bottom. Using
screws or a wire tie, mount the crossover using the holes
provided. Observing proper polarity, connect the speakers
and amplifier as shown in Figures 8A and 8B. Replace the
cover when you are finished making the connections and
adjustments (see following section).
The Power Series component crossover features a
tweeter-level adjustment. The tweeter level may be set to
0dB (flat response), or it may be attenuated by approxi-
mately 3dB to suit the listener’s preference. The factory
default position is 0dB; if this is the desired setting, it is
not necessary to make any changes.
4
)
–
blk
red
+
3
)
1) push in
If a reduced tweeter output level is desired, carefully
remove the small plastic jumper from the pins marked
“0dB” and place it across the two pins marked “–3dB”
(refer to drawings below).
Figure 8A. Wiring connections
on the crosssover network
(shown with cover on).
2
)
turn
Figure 6. Aiming the tweeter at a
desired listening position.
Jumper
3. Rotate to aim
angled tweeter
toward listener.
P O W E R P 5 5 0 C
2 R 0
0dB
1. Slide screw up or
down to adjust
tweeter angle.
-3dB
R1
Flat
2R0
Red
C 2
0dB
To AMPLIFIER
SPEAKER OUTPUTS
2.Tighten nut and
washer to lock
angle settings.
-3dB
0dB
To TWEETER
To WOOFER
Blk
In- In+ W- W+ T- T+
-3dB
Figure 8B. Locating wiring connections
on the P552 woofer. Other woofers
are wired similarly.
4. Securely tighten
the large hand nut.
–3dB
Jumper
Figure 7. Mounting the tweeter using
the I-Mount surface-mounting kit.
blk
–
+
red
1
Big Lug =
2
Sm all Lug =
Download from Www.Somanuals.com. All Manuals Search And Download.
S P E C IF IC A T IO N S
P550c
P650c
Type:
5-1/4" two-way component system
6-1/2" two-way component system
Speaker Impedance:
Power Handling:
Sensitivity (2.83V, 1m):
Frequency Response:
Mounting Depth:
Cut-Out Diameter:
4 ohms
4 ohms
70W RMS, 210W Peak
89dB
90W RMS, 270W Peak
90dB
55Hz – 23kHz
2-3⁄16" (56mm)
4-11/16" (120mm)
45Hz – 23kHz
2-1/4" (58mm)
5-1/16" (129mm)
GENERAL CARE
The loudspeaker grilles may be cleaned with a damp cloth. Do not use any cleaners or solvents on the grilles or the speaker cones.
A valid serial number is required for warranty coverage.
Features, specifications and appearance are subject to change without notice.
Declaration of Conformity
We, Harman Consumer International
2, route de Tours
72500 Chateau-du-Loir
France
JBL Consumer Products
declare in own responsibility that the products
described in this owner’s manual are in compliance
with technical standards:
250 Crossways Park Drive, Woodbury, NY 11797 USA
© 2003 Harman International Industries, Incorporated
EN 50081-1:1992
EN 50082-1:1997
JBL is a registered trademark of
Harman International Industries, Incorporated.
Emmanuel Millot
Harman Consumer International
Chateau-du-Loir, France. 2/03
Part No. P550C/P650COM2/03
Download from Www.Somanuals.com. All Manuals Search And Download.
|