530e
Owner’s Manual
IRONMAN 530e ELLIPTICAL
Customer Service
1.800.750.IRON
1.800.750.4766
Ironman Fitness
4009 Distribution Drive
Suite 250
Garland, TX 75041
Model Name :530e
Serial Number :
Write down for future reference
Serial Number Decal Location
315-00083
07/07 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
WARNING! Before using this unit or starting any exercise program, consult your physician.
This is especially important for persons over the age of 35 and/or persons with pre-existing
health problems. The manufacturer or distributor assumes no responsibility for personal injury
or property damage sustained by or through the use of this product.
SAFETY PRECAUTIONS AND TIPS
1. It is the owner's responsibility to ensure that all users of this unit have read the Owner's
Manual and are familiar with warnings and safety precautions.
2. This unit has a user maximum capacity of 300 pounds.
3. The unit should only be used on a level surface and is intended for indoor use only. The unit
should not be placed in a garage, patio, or near water and should never be used while you are
wet. Ironman Fitness recommends a mat be placed under the unit to protect floor or carpet
and for easier cleaning.
4. Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not
use the unit with bare feet, sandals, socks or stockings.
5. Always examine your unit before using to ensure all parts are in working order.
6. Allow the unit to fully stop before dismounting.
7. Pets should never be allowed near the unit.
8. Do not leave children unsupervised near or on the unit.
9. Never operate the unit where oxygen is being administered, or where aerosol products are
being used.
10. Never insert any object or body parts into any opening.
11. For safety and to prevent damage to your unit, no more than one person should use the
unit at a time.
12. Service to your unit should only be performed by an authorized service representative,
unless authorized and/or instructed by the manufacturer.
13. Failure to follow these instructions will void the unit warranty.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Thank you for purchasing the Ironman 530e Elliptical! This quality product you have chosen
was designed to meet your needs for cardiovascular exercise. Before you start, please read the
Owner's Manual and become familiar with the operation of your new unit.
Remember to take the time to perform the stretching exercises provided to avoid
injury.
If you are taking medication, consult your physician to see if the medication will affect your exer-
cise heart rate.
If you have heart problems, you are not active, and/or are over the age of 35 years, do not use
the pre-set programs or start an exercise program without first contacting and receiving approval
from your physician.
To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the con-
sole. Ironman Fitness recommends a sealed water bottle for beverages consumed while using
the unit.
Please review the following drawing below to familiarize yourself with the listed
parts.
CONSOLE
HANDLEBARS
PULSE GRIPS
MAIN FRAME
TRANSPORT WHEEL
PEDALS
FRONT FOOT TUBE
REAR FOOT TUBE
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
INSTRUCTIONS FOR ASSEMBLY:
Unpack the box in a clear area. Check to make sure all components are present and in
good condition. Do not dispose of the packing material until the assembly is completed.
Tools have been provided for you to use when assembling this product.
Locate the hardware pack and identify the following parts required for assembly.
Tools:
1. Allen Wrench
2. Wrench
Main Components:
1. OWNER’S MANUAL
2. MAIN FRAME
3. PULSE GRIPS
4. HANDLEBARS
5. TRANSPORT WHEEL
6. REAR FOOT TUBE
7. FRONT FOOT TUBE
8. AC ADAPTER
9. PEDALS LEFT AND RIGHT
Hardware:
1. SCREW, M8X15MM (56) - Qty 3
2. M8X19MM WASHER BLACK (50) - Qty 23
3. SCREW, M8X90MM (58) - Qty 2
4. 8 MM BLACK LOCKNUTS (THICK) (49) - Qty 12
5. SCREW, M8X20MM (BLACK) (64) - Qty 4
6. M8X80MM HEX HEAD SCREW (62) - Qty 4
7. M8X60MM SCREW (55) - Qty 3
8. BLACK LOCKNUT, M8 THIN (79) - Qty 3
9. M8X20MM HEX HEAD SCREW (LOCKTITED) (89) - Qty 4
10. SHEET METAL SCREW, M5X10MM (59) - Qty 2
11. WASHER, M10X38X1.5 (61) - Qty 2
12. WASHER, M10X23X1.5 (68) - Qty 4
13. BLACK LOCKNUT, 10MM (THIN) (52) - Qty 8
14. M21 WAVED WASHER (77) - Qty 2
15. SCREW, M10X57MM (67) - Qty 2
16. SPACER, 15.8X10X4.3t (98) - Qty 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Figure 1
FIGURE 1
Step 1:
Attach Extrusions (45,97) to
Main Frame (1) using Screws
(56), Washers (50), Bolts (58),
Washers (50) and Nuts (49).
Step 2:
Attach Extension Plate (34) to
Extrusions (45,97) using four
Screws (64) and four Washers
(50).
Figure 2
FIGURE 2
Step 1:
Attach Right Rear Foot Frame
(33) to Right Foot Frame (31)
using two Bolts (62), two
Washers (50) and two Nuts
(49).
Step 2:
Repeat for left side.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Figure 3
FIGURE 3
Step 1:
Connect Cables 27,8 and 71
to Cable 28.
Step 2:
Slide Main Upright (2) onto
Main Frame (1). Be care-
ful not to pinch the cables.
Attach Main Upright to Main
Frame using four Bolts (55),
four Washers (50) and four
Nuts (79).
Step 3:
Attach Console Tube Collar
(14) using two Bolts (89) and
two Washers (50).
Figure 4
FIGURE 4
Step 1:
Feed Hand Pulse Wires (26)
thru Main Upright (2).
Step 2:
Attach Pulse Grip Handlebar
(10) to Main Upright (2) using
two Bolts (55), two Washers
(50) two Nuts (49), one Screw
(56) and one Nut (50).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
FIGURE 5
Step 1:
Figure 5
Connect Cables as shown.
Note: Be careful not to pinch
wires. Excess wire should
be pushed back into Main
Upright.
Step 2:
Attach Console (5) to Main
Upright using four Screws
(59).
Note: The four Screws(59)
will already be installed into
the back of Console (5) when
you remove it from the box.
Step 3:
Attach Reading Rack by
inserting into holes located on
the console.
Step 4:
Remove protective over-
lay screen from the console
screen.
Figure 6
FIGURE 6
Step 1:
Attach Left Handlebar (3)
using Spacer (19), Washer
(61), Washer (68), Cap (21),
Nut (52) and Cap (22).
Step 2:
Repeat for Right Handlebar
(4).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Figure 7
FIGURE 7
Step 1:
Attach Bottle Rack (2A) using
two Screws (77).
Step 2:
Attach Handlebars (3 & 4) to
Connecting Arm (29) using Bolt
(67), Nut (98), Washer (69)
and Nut (52).
Congratulations!
You have completed assembly of your new Ironman 530e Elliptical!
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Overview
CONSOLE BUTTONS:
MODE:
To set function value for TIME, DIST, CAL, PULSE.
RESET:
Return to main function mode in STOP mode and clean all preset function values at zero.
START/STOP:
To start or stop training
RECOVERY:
To test hear rate recovery status.
UP:
To select training mode and adjust function value up.
DOWN:
To select training mode and adjust function value down.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Overview
FAN ON/OFF:
Press the button to act or stop fan turning.
BODY FAT:
Press the button to start body fat measurement.
CONSOLE FUNCTIONS
TIME:
Count up - No preset target, Time will count up from 00:00 to maximum 99:59 with each
increment is 1 second. Count down - If training with preset Time, Time will count down from
preset to 00:00. Each preset Increment or decrement is 1 minute between 1:00 to 99:00.
SPEED:
Display current training speed from 0.0 to maximum 99.9 km or ml.
RPM:
Display current training rotation per minute.
DISTANCE:
Count up - No preset target, Distance will count up from 0.00 to maximum 99.90 with each
Increment 0.1 KM. Count down - If training with preset target, Distance will count down from
preset to 0.00. Each preset increment or decrement is 0.1 KM (or ML) between 0.00 to 99.90.
CALORIES:
Count up - No preset target, Calories will count up from 0 to maximum 990 with each 1 cal
increment. Count down - If training with preset target, Calories will count down from preset
time to 0. Each preset increment or decrement is 10 cal from 0 to 990 cal.
PULSE:
Displays your current heart beat figures as soon as both hands are holding the pulse sensor.
The monitor will detect your heart rate through hand grip sensors or chest strap (make sure
that the plug in receiver has been attached to the console), with the chest strap giving the
most accurate reading.
WATT:
Display current training watt figures.
RECOVERY:
After exercising for a period of time, keep holding on handgrips and press “RECOVERY” but-
ton. All function display will stop except “TIME” starts counting down from 00:60 to 00:00.
Screen will display your heart rate recovery status with the F1, F2 to F6. F1 is the best, F6
is the worst. User may keep exercising to improve the heart rate recovery status. (Press the
RECOVERY button again to return the main display.)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Overview
TEMPERATURE:
Screen will display room temperature in sleep mode.
CALENDAR:
Screen will display year/month/day in sleep mode.
CLOCK:
Screen will display time in sleep mode.
BODY FAT:
You may test and have the BODY FAT advice when the computer is in STOP mode. Please follow
the steps as below:
Step I - Make sure the personal data have been input and correct.
Step II - Press BODY FAT button, and hold on handgrip to start body fat testing.
Step III - The symbol "- - - - - - - - " will display while testing period in 8 seconds. After 8
seconds, you will see the BODY FAT advice in percentage and BMI and the fat advice in differ-
ent symbol. It would be possible to display other indication if you have the following situation:
1. "E-1" - When you see this indication, it means you did not put your hands properly on
the sensor. Please try again.
2. "E-4" - When you see this indication, it means the BODY FAT advice is exceeded the
available area which is fixed in the program.
After BODY FAT testing, press BODYFAT button to have the computer back to working continues
from the previous data before testing. The BODY FAT advice figure and BMI will disappear. The
computer may allow the other people to test BODY FAT under STOP mode. The user may press
RESET button for 4 seconds to select new user identification and input new personal data. Then
follow each step as above to have the new testing.
Note: For a more accurate reading, hold the handgrip with both hands. This is
especially important in Heart Rate Mode or when performing Body Fat or Fitness Test.
GENERAL INFORMATION:
Start Pedaling or press any button to start Console.
The Console will shut down after 4 minutes of no activity, and will display room temperature.
To Reset Console press and hold the START/STOP button for 2 seconds.
The Console has a fan. There is a button on the left side of the console that controls the fan.
The values calculated or measured by the console are for exercise purposes only, not for
medical purposes.
Body Types:
There are 5 body types divided according to the FAT% calculated. Type 1= 5%-14%, Type 2 =
15%-24%, Type 3 = 25%-29%, Type 4= 30%-39% and Type 5 40%-50%.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Overview
BMR:
Basal Metabolic Rate (metabolism) is the energy (measured in calories) expended by the body
at rest to maintain normal body functions.
BMI:
Stands for Body Mass Index. BMI is a measure which takes into account a person’s weight and
height to gauge total body fat in adults.
GETTING STARTED:
Press the USER button. Press ENTER to enter USER SELECT. Use the UP/DOWN to select a
User. Press ENTER to select a User. Press the UP/DOWN key to select HEIGHT. Press ENTER
to confirm the value. Use the UP/DOWN key to select WEIGHT. Press ENTER to confirm value.
Use the UP/DOWN key to select AGE. Press ENTER to confirm value. Use the UP/DOWN key to
select GENDER. Press ENTER to confirm value. Press START/STOP to enter program mode.
PROGRAM INSTRUCTIONS:
MANUAL PROGRAM:
Allows the User to manually adjust tension settings throughout their workout. The default ten-
sion level is 6. You may set Time or Distance for your workout.
Use the UP/DOWN buttons to scroll to this program. Press ENTER to select this program. TIME
will flash in the display. Use the UP/DOWN keys to set desired TIME. Press ENTER to confirm
value. Repeat steps for DISTANCE and KCAL. Press START/STOP to begin exercising. Grasp
Pulse Grips loosely with both hands to activate PULSE function. You can change the tension
level at any time during your workout session by pressing the UP/DOWN buttons.
PRESET PROGRAMS:
Each Program is divided into ten intervals.
Use the UP/DOWN buttons to scroll to this program. Press ENTER to select this program. TIME
will flash in the display. Use the UP/DOWN keys to set desired TIME. Press ENTER to confirm
value. Repeat steps for DISTANCE and KCAL. Press START/STOP to begin exercising. Grasp
Pulse Grips loosely with both hands to activate PULSE function.
USER PROGRAM:
It allows you to customize a workout session. This program is divided into 10 intervals. TIME,
DISTANCE, KCAL and Tension can be set for each interval. The program will be stored in the
Console’s memory after set-up.
Use the UP/DOWN buttons to scroll to this program. Press ENTER to select this program. TIME
will flash in the display. Use the UP/DOWN keys to set desired TIME. Press ENTER to confirm
value. Repeat steps for DISTANCE and KCAL. Column 1 will flash on display. Use the UP/
DOWN keys to set Tension for this interval. Press ENTER to confirm value. Repeat for Interval
2-10. Press START/STOP to begin exercising. Grasp Pulse Grips loosely with both hands to
activate PULSE function. You can change the tension level at any time during your workout
session by pressing the UP/DOWN buttons. If the tension level is changed during your exercise
session, this new value will not be saved into the console.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Overview
To make a permanent change, you must call up program again and repeat steps for each inter-
val with new tension settings.
WATT PROGRAM:
In the program, the WATT function will keep a constant value. This means that if your peddle
quickly, the tension will decrease, if you peddle slowly the tension will increase to try and keep
you the same Watt value.
WATT = TORQUE (KGM) * RPM *1.03 For this program you must choose to set a TIME or a
DISTANCE. Use the UP/DOWN buttons to scroll to this program. Press ENTER to select this
program. TIME will flash in the display. Use the UP/DOWN keys to set desired TIME. Press
ENTER to confirm value. Repeat steps for DISTANCE, KCAL and WATT. Press START/STOP to
begin exercising. Grasp Pulse Grips loosely with both hands to activate PULSE function.
HEART RATE PROGRAMS:
There are three Heart Rate Programs. 60% HRC (Heart Rate Control), 75% HRC and 85%
HRC. The Console will adjust the Tension to keep you within your Target Heart Rage ± 5.
Example: The tension will increase if your Heart Rate is below the Target Heart Rate. The ten-
sion will decrease if your Heart Rate is higher that your Target Heart Rate.
Press ENTER until Program number shows on display. Use the UP/DOWN buttons to scroll to
this program. Press ENTER and set values for TIME, DISTANCE, KCAL, AGE and TARGET HEART
RATE. Use the UP/DOWN keys to adjust the values. Press ENTER after correct value shows on
display. Press START/STOP to begin exercising. Grasp Pulse Grips loosely with both hands to
activate PULSE function. You may also choose the TARGET HEART RATE WORKING PROGRAM
under the 3 main HEART RATE PROGRAMS. This allows the user to set a TARGET HEART RATE
to exercise at for a period of TIME or a set DISTANCE.
BODY FAT PROGRAM:
This program is designed to calculate body fat ratio and to design a specific tension profile.
There are 5 different body types according to the FAT% calculated. Press ENTER until Program
number shows on display. Use the UP/DOWN buttons to scroll to this program. Press ENTER
and set values for HEIGHT, WEIGHT, AGE and SEX. Use the UP/DOWN keys to adjust these
values. Press the START/STOP key to calculate body fat. Grasp Pulse Grips loosely with both
hands to activate Pulse function. If no Pulse is detected an error message “ERROR” will show
on display. If this happens, press START/STOP again and re-grasp Pulse Grips. Press ENTER
button to scroll thru results: Fat Weight, Fat%, BMR, BMI and Body Type.
Body Types: Type 1 = 5%-14%
Type 2 = 15%-24%
Type 3 = 25%-29%
Type 4 = 30%-39%
Type 5 = 40%-50%.
FITNESS TEST: (Pulse Recovery Feature)
The fitness test compares your pulse rate before and after training. You will notice that your
fitness will improve with regular exercise.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Overview
Press the PULSE RECOVERY button immediately after your workout. Grasp the Pulse Grips.
Timer will count down from 60 seconds. Your personal fitness will display on the screen.
(F1.0-6.0)
F1 = Excellent
F2 = Good
F3 = Fair
F4 = Below Average
F5 = Poor
F6 = Very Poor
To change console settings from MPH (Miles Per Hour) to
KPH (Kilometers Per Hour) flip switch on back of unit.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Your Heart Rate
Monitoring Your Heart Rate
To obtain the greatest cardiovascular benefits from your exercise workout, it is important to
work within your target heart rate zone. The American Heart Association (AHA) defines this tar-
get as 60%-75% percent of your maximum heart rate.
Your maximum heart rate may be roughly calculated by subtracting your age from 220. Your
maximum heart rate and aerobic capacity naturally decreases as you age. This may vary from
one person to another, but use this number to find your approximate effective target zone. For
example, the maximum heart rate for an average 40 year-old is 180 bpm. The target heart
rate zone is 60%-75% of 180 or 108-135 bpm. See Fitness Safety below.
Before beginning your workout, check your normal resting heart rate. Place your fingers lightly
against your neck, or against your wrist over the main artery. After finding your pulse, count
the number of beats in 10 seconds. Multiply the number of beats by six to determine your
pulse rate per minute. We recommend taking your heart rate at these times; at rest, after
warming up, during your workout and two minutes into your cool down, to accurately track
your progress as it relates to better fitness.
During your first several months of exercising, the AHA recommends aiming for the lower part
of the target heart rate zone-60%, then gradually progressing up to 75%.
According to the AHA, exercising above 75% of your maximum heart rate may be too strenu-
ous unless you are in top physical condition. Exercising below 60% of your maximum will result
in minimal cardiovascular conditioning.
Check your pulse recovery rate – If your pulse is over 100 bpm five minutes after you stop
exercising, or if it’s higher than normal the morning after exercising, your exertion may have
been too strenuous for your current fitness level. Rest and reduce the intensity next time.
Fitness Safety The target heart rate chart indicates average rate zones for different ages. A
variety of different factors (including medication, emotional state, temperature and other condi-
tions) can affect the target heart rate zone that is best for you. Your physician or health care
professional can help you determine the exercise intensity that is appropriate for your age and
condition.
(MHR) = Maximum Heart Rate
(THR) = Target Heart Rate
220 - age = maximum heart rate (MHZ)
MHZ x .60 = 60% of your maximum heart rate.
MHZ x .75 = 75% of your maximum heart rate.
For example, if you are 30 years old, your calculations will be as
follows:
220 - 30 = 190
190 x .60 = 114 (low end or 60% of MHZ)
190 x .75 = 142 (high end or 75% of MHZ)
30 year-old (THR) Target Heart Rate would be 114-142
See Heart Rate Table (on next page) for additional calculations.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Your Heart Rate
TARGET HEART RATE ZONE
200
100%
195
190
185
180
175
Serious
athletic
170
165
160
training range
155
132
85%
170
150
166
146
162
143
157
139
153
135
Cardiovascular
conditioning
range
149
131
105
145
128
102
140
124
99
136
120
96
75%
Fat burning
range
116
93
120
60%
117
114
111
108
20 25 30 35
40 45 50 55 60 65
AGE
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving Instructions
Caution! To reduce the possibility of injury while lifting, bend your legs and keep
your back straight. As you lean the unit, lift using your legs, not your back.
Stand at the front of the unit and using the small handlebar, carefully tilt the machine until
the weight is transferred to the transport wheels. Using extreme caution, move the unit to the
desired location. To set the unit down, carefully lower unit onto rear foot tube assembly in a
resting position. Do not attempt to move the unit over an uneven or rough surface.
Note: This unit may not be identical to your unit.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Warm Up Exercises
EXERCISE GUIDELINES
WARNING! Before beginning this or any exercise program, you should consult your physi-
cian. This is especially important for individuals over the age of 35 or individuals with pre-exist-
ing health problems.
Warming up prepares the body for the exercise by increasing circulation, supplying more oxy-
gen to the muscles and raising body temperature. Begin each workout with 5 to 10 minutes of
stretching and light exercise to warm up. The photos on this page show several forms of basic
stretching you may perform before your workouts. In order to achieve an adequate warm-up,
perform each stretch three times.
TOE TOUCH STRETCH
Stand bending your knees slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. This will stretch your hamstrings, back of knees, and
back.
HAMSTRING STRETCH
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. This will stretch your hamstrings, lower back,
and groin.
CALF/ACHILLES STRETCH
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. To
cause further stretching of the Achilles tendon, bend your back
leg as well. This will stretch your calves, Achilles tendons, and
ankles.
QUADRICEPS STRETCH
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. This will
stretch your quadriceps and hip muscles.
INNER THIGH STRETCH (not pictured)
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. This will stretch your quadriceps and hip
muscles.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
530e Elliptical Parts List Rev A
Ref #
1
2
2A
3
4
5
6
7
8
Part #
Description
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
54
2
4
2
2
2
2
2
2
2
1
2
2
1
1
1
1
1
1
1
1
1
6
8
2
4
4
2
3
1
1
2
1
4
4
2
12
23
5
8
Ref #
53
Part #
Description
Qty
2
1
3
3
1
1
2
2
12
2
4
1
4
2
2
2
4
2
8
1
2
1
1
1
2
2
2
3
2
1
2
2
2
4
4
1
1
4
1
2
3
2
2
1
2
1
2
1
4
2
6
2
2
1
323-00311 MAIN FRAME ASSEMBLY, 500E/520E
323-00257 MAIN UPRIGHT HT840EL/520E (GREY)
310-00012 BOTTLE RACK CM835/850 HT840 ALL900/920/5
323-00376 LEFT FOAM HANDLE, 520E
305-00031 ROUND COVER ET CM835/850 HT840 AB900/920
319-00177 AXLE W/PLATE, HT840R/HT840U.1/420R/500e
302-00377 M8X60MM SCREW
302-00186 SCREW, M8X15MM
305-00140 ROUND LEFT DOME COVER, HT840EL.1/520E
54
55
56
57
323-00377 RIGHT FOAM HANDLE, 520E
307-00127 CONSOLE, 430R/530E
311-00059 PULLEY HT840U/R/EL/420R/520E
311-00058 MAGNETIC FLYWHEEL, HT840EL/520E
307-00128 GEAR BOX W/WIRE, 430R/530E
304-00001 BELT, J6 460
57A 305-00141 ROUND RIGHT DOME COVER, HT840EL.1/520E
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
302-00189 SCREW, M8X90MM
302-01259 SHEET METAL SCREW, M5X10MM
302-01234 ALLEN BOLT, M6X15MM
9
302-01258 WASHER, M10X38X1.5
10
11
12
13
14
15
16
17
18
323-00378 FRONT HANDLEBAR, 520E
302-00450 M8 X80MM HEX HEAD SCREW 220E/240E/240R/U
302-01257 SCREW, M8X20MM (CARBON)
302-01253 SCREW, M8X20MM (BLACK)
302-01249 SCREW, M10X47MM
302-01250 SCREW, M10X45MM
302-01251 SCREW, M10X57MM
302-01252 WAHER, M10X23X1.5
331-00002 608 PRECISE BEARING
331-00092 PRECISE BEARING, 6005
313-00213 REED SWITCH WIRE, 520E
302-00985 CRANK NUT M14, HT840EL/520E
330-00019 LEFT CRANK ET835/850/900/920 HT840EL/520
330-00018 RIGHT CRANK ET835/850/900/920 HT840EL/52
302-00071 SHAFT NUT M20,ET835/850 HT840EL ET900/92
319-00174 JOINTER, HT840EL/520E
305-00065 BOTTOM LEFT COVER#11 HT840EL W/FAN/520E
305-00066 BOTTOM RIGHT COVER#12 HT840EL W/FAN/520
305-00142 TOP HOUSING, 520E
305-00143 CONSOLE TUBE COLLAR, 520E
302-00471 M4 X 12MM SHEET METAL SCREW TRI-6.0R,640
306-00691 FOOT PEDAL, 530E
306-00586 40X80 END CAP#17
306-00662 LEFT ROLLER CAP, 520E
18A 306-00663 RIGHT ROLLER CAP, 520E
19
20
21
22
23
24
25
26
27
28
29
302-01268 SNAP CAP, 520E/HT840EL.1
319-00128 WHEEL, HT840EL/520E
302-01028 SNAP CAP, HT840EL/520E
302-01029 BUSHING CAP, HT840EL/520E
302-00981 076MMX16MM BUSHING
306-00591 0 16MM INNER TUBE, HT840EL/520E
313-00362 SENSOR, HAND PULSE 530E
313-00363 WIRE, HAND PULSE 530E
313-00364 EXTENSION WIRE, 530E
313-00364 EXTENSION WIRE, 530E
323-00384 LEFT CONNECTING ARM, 520E
302-01256 M21 WAVED WASHER
302-00848 RETAINING RING, HT840EL/520E/ET920D
302-01255 BLACK LOCKNUT, M8 THIN
302-01254 WASHER, M16X29X15
302-00375 M8X38MM SCREW
306-00338 BALL PLUG 1 1/2, 220E/240E/HT840EL.1/520
306-00372 1 1/4" BALL PLUG 220R/240R/240U/640R/520
306-00651 SPACER, M13.95X10X8L
302-00858 16MM BUSHING#85
302-00859 32MM BUSHING
319-00175 BELT TENSION BRACKET,HT840R/HT840U.1,420
302-01269 MAGNET, 520E/HT840EL.1
302-01248 M8X20MM HEX HEAD SCREW
302-00448 M8 X12.5X4L SPACER 220E/240E/240R/240U/5
302-00759 M26 CURVED WASHER
302-00417 TP M5 X50MM SCREW
302-01247 WASHER, M8X30X1.5
302-01246 WASHER, M13X24X2
310-00185 TENSION CABLE (DRIVE CABLE), 520E
302-00467 TP M3 X8MM SCREW 220R/240R/640R/520e/250
323-00387 LEFT ALUMINUM EXTRUSION, 520E
302-01261 SPACER, 15.8X10X4.3t
29A 323-00385 RIGHT CONNECTING ARM, 520E
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
323-00383 FRONT LEFT FOOT FRAME, 520E
323-00382 RIGHT FRONT FOOT FRAME, 520E
323-00381 LEFT REAR FOOT FRAME, 520E
323-00380 RIGHT REAR FOOT FRAME, 520E
323-00379 ALUMINUM EXTENSION PLATE, 520E
331-00091 PRECISE BEARING, #6004
331-00093 PRECISE BEARING, 6000
306-00692 SLEEVE, HANDLEBAR 38MM 530E
302-01022 0 32MM BUSHING
302-01227 HEX BOLT, M6X20 (SILVER)
302-00399 ADJUSTMENT CHANNEL ALL MACRO BIKES
302-01195 EYEBOLT 6 X 40MM
302-00203 SPRING,HT840EL/520E
311-00032 IDLER PULLEY U/R/ET CM835/850 HT840 AB90
306-00661 ROLLER, 520E
323-00386 RIGHT ALUMINUM EXTRUSION, 520E
302-01228 LOCKNUT, 6MM (SILVER)
302-01229 HEX NUT, 6MM (SILVER)
302-01239 WASHER, M20X30X1 (SILVER)
100 302-01262 ALLEN BOLT, M5X10MM
101 302-00376 M8X57MM SCREW
102 302-01192 TP M4 X 16 MM SCREW
103 302-00435 M10 CURVED WASHER 220E/240E/520e
104 302-01230 WASHER, M10X19MM (BLACK)
302-00369 M10 CAP NUT
302-01231 8MM BLACK LOCKNUT (THICK)
302-00449 M8X19MM WASHER BLACK U/R/E 220/240/250
302-01226 WASHER M20X30X2, (SILVER)
302-01260 BLACK LOCKNUT, 10MM (THIN)
#
315-00083 OWNERS MANUAL 530E
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Information
Residential Warranty
Frame: Lifetime
Parts: 1 Year
This Limited Warranty applies in the United States and Canada to products manufactured or
distributed by Ironman Fitness (“Ironman”) under the Ironman brand name. The warranty peri-
od to the original purchaser is listed above in the table.
Ironman warrants that the Product you have purchased for use from Ironman or from an
authorized Ironman reseller is free from defects in materials or workmanship under normal use
during the warranty period. Your sales receipt, showing the date of purchase of the Product,
is your proof of purchase. This warranty only extends to you, the original purchaser. It is not
transferable to anyone who subsequently purchases the Product from you. It excludes expend-
able parts (wear items). Wear items pertain to components that might need to be replaced
due to normal wear and tear. These items vary per product but will include pedal straps, seats,
grips, chains, bottom bracket assemblies, pads, etc. Please contact an Ironman customer ser-
vice representative for specifics on wear items. This Limited Warranty becomes VALID ONLY if
the product is purchased through an Ironman Fitness authorized dealer unless otherwise autho-
rized by Ironman Fitness in writing.
During the warranty period Ironman will repair or replace (at Ironman’s option) the product
if it becomes defective, malfunctions, or otherwise fails to conform with this Limited Warranty
under normal use. In repairing the Product, Ironman may replace defective parts, or at the
option of Ironman, serviceable used parts that are equivalent to new parts in performance.
All exchanged parts and Products replaced under this warranty will become the property of
Ironman. Ironman reserves the right to change manufacturers of any part to cover any existing
warranty.
This warranty DOES NOT COVER shipping charges, export taxes, custom duties and taxes, or
any other charges associated with transportation of the parts or Product.
To obtain warranty service, you must contact an Ironman authorized retailer, service techni-
cian or Ironman Fitness at our phone number located in this manual. Any parts determined to
be defective must be returned to Ironman to obtain warranty service. You must prepay any
shipping charges, export taxes, custom duties and taxes, or any other charges associated with
transportation of the parts or Product. In addition, you are responsible for insuring any parts
or Product shipped or returned. You assume the risk of loss during shipment. You must present
Ironman with proof-of-purchase documents (including the date of purchase). Any evidence of
alteration, erasing or forgery of proof-of-purchase documents will be cause to void this Limited
Warranty.
This warranty does not extend to any product not purchased from Ironman or from an autho-
rized Ironman reseller. This Limited Warranty does not extend to any Product that has been
damaged or rendered defective; (a) as a result of accident, misuse, or abuse; (b) by the use
of parts not manufactured or sold by Ironman; (c) by modification of the Product or normal
wear and tear; (d) operation on incorrect power supplies; or (e) as a result of service by any-
one other than Ironman, or an authorized Ironman warranty service provider. Product on which
the serial number has been defaced or removed is not eligible for warranty service. Should any
Product submitted for warranty service be found ineligible, an estimate of repair cost will be
furnished and the repair will be made if requested by you upon Ironman’s receipt of payment
or acceptable arrangements for payment.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, IRONMAN MAKES NO OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IRONMAN EXPRESSLY
DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED
WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED
WARRANTY. NEITHER IRONMAN NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION
MAY NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights and you may
also have other rights that may vary from state to state. This is the only expressed warranty
applicable to Ironman-branded products. Ironman neither assumes nor authorizes anyone to
assume for it any other express warranty.
PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHIN TEN (10) DAYS OF PURCHASE TO
REGISTER YOUR UNIT WITH IRONMAN FITNESS.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Service
1.888.340.0482
Keys Fitness
4009 Distribution Drive
Suite 250
Garland, TX 75041
Ironman and M-dot are registered trademarks of the World Triathlon Corp., used here by permission.
Download from Www.Somanuals.com. All Manuals Search And Download.
|