Tray Mounting Hardware
Assembly,Installation and Operating Instructions
Right Side Hardware
Part Nos.TR40R
Left Side Hardware
Part No.TR40L
6. Insertthesupportarmfullyintothetrayreceptacle untilit
SAVE THESE INSTRUCTIONS
cannot move further back.
NOTE: Check all parts for shipping damage before using.
In case of damage, do not use. Contact the dealer for fur-
ther instructions.
7. Have the user sit in the wheelchair and position the tray
on the armrests, evenly spaced on both sides.
8. Withapenlocateandmarkthefour(4)drillpointsonthe
tray by using the support arm bracket as a template.
SAFETY SUMMARY
9. Using a 1/4" drillbit, drill four (4) holes corresponding to
the marks made with the pen.
The following reccommendations are made for safe in-
stallation and use of the Tray Mounting Hardware:
GENERAL WARNINGS
NOTE: This product is designed to work with Invacare trays
LTACL, LTCCL, LTACCL and LTCCCL. The Invacare tray
mounting hardware can also be installed on other manufac-
turers' trays if the tray rim does not interfere with the opera-
tion of the tray support arm.
DO NOT insta ll this e q uip m e nt witho ut first
re a d ing a nd und e rsta nd ing this instruc tion
she e t. If yo u a re una b le to und e rsta nd
the se Wa rning s, Ca utions a nd Instruc tions,
c o nta c t a he a lthc a re p ro fe ssio na l, d e a le r
o r te c hnic a l p e rso nne l if a p p lic a b le b e -
fo re a tte m p ting to insta ll this e q uip m e nt -
othe rwise , injury or d a m a g e m a y oc c ur.
C AUTIO N
DO NOT drill too de e p a s this will re nde r the
tra y use le ss.
Co nsult a p hysic ia n o r the ra p ist fo r a p -
p ro p ria te p o sitio ning o f the tra y re la tive
to the use r.
10. Counter-sink the holes to accomodate the flat screws
includedinthekit.
11. Mountthetrayusing theflatscrews,washers,andacorn
nuts with the hex key wrench provided. DO NOT over-
tighten screws.
Your the ra pist a nd physic ia n should be c on-
sulte d if yo u ha ve a ny q ue stio ns re g a rd -
ing ind ivid ua l lim ita tions a nd ne e d s.
12. With the user sitting in the wheelchair, adjust the tray to
the desired position and tighten knob on receptacle.
The tray mounting hardware is available in two versions
TR40R: Right side hardware (shown)
TR40L: Left side hardware
NOTE: The strap on the tray may be removed or wrapped
around armrest for additional support.
Tools Required:
1/4-inch drillbit, a 82-degree counter sink drill, a hand drill,
a phillips screwdriver and a 1/2-inch open end wrench.
Armrest Pad
Flat
Tray
Screws
INSTALLATION (FIGURE 1)
1. Remove the armrest from the wheelchair. Refer to
the wheelchair owner's manual.
2. Using a Phillips screwdriver remove the armrest pad
from the armrest and set the screws aside.
Strap
3. Adjust the clamp brackets on the tray receptacle so
thatone(1)ofthefour(4)holesoneachclampbracket
line up with one (1) armrest hole.
Knob
Tray
Clamp
Support
Arm
Bracket
Receptacle
4. Secure the armrest pad and tray receptacle assem-
blytothearmrestwiththepreviouslyremovedscrews
as shown in FIGURE 1.
Washer
Support Arm Bracket
(use as template)
Acorn Nut
5. Put both armrests on the wheelchair.
FIG URE 1 - INSTALLATIO N
Invacare Corporation
USA
Canada
One InvacareWay
Elyria, Ohio USA
44036-2125
5970 ChedworthWay
Mississauga, Ontario
L5R 3T9, Canada
800-668-5324
Invacare is a registered trademark of Invacare Corporation.
©
1999 Invacare Corporation
800-333-6900
Form No. 99-120 Part No. 0900121 Rev C (2) 12/99
Download from Www.Somanuals.com. All Manuals Search And Download.
|