Personal Back Bottom Mounting Hardware
Assembly,Installation and Operating Instructions
Kit No. MB-54
This kit includes the following:
SAVE THESE INSTRUCTIONS
ITEM
COMPONENT
QTY.
NOTE: Check all parts for shipping damage. In case of
damage, DO NOT use. Contact Carrier/Invacare for fur-
ther instruction.
1.
2.
3.
4.
5.
6.
7.
8.
Threaded Latch Pin
NylonLockingKey
End Cap for Latch Pin
3/16-inch Retaining Ring
UtilitySpring
#10 Flat Washer
Ziplock Bag *
Carton *
2
2
2
2
2
2
1
1
SAFETY SUMMARY
The following recommendations are made for the
safeinstallationofthePersonalBackBottomMount-
ing Hardware:
GENERAL WARNINGS
DO NOT insta ll this equipment without first rea d-
ing a nd understa nding this instruction sheet. If you
a re una ble to understa nd the Wa rnings, Ca utions
a nd Instruc tions, c onta c t a he a lthc a re profe s-
siona l, de a le r or te c hnic a l pe rsonne l if a ppli-
ca ble before a ttempting to insta ll this equipment
- otherwise, injury or da ma ge ma y occur.
* NOT SHOWN
INSTALLING HARDWARE (FIGURE 1)
1. Move foam padding on inside of Personal Back shell
to access the mounting holes.
2. Insert the Threaded Latch Pin (Item 1) from the back
of the Personal Back, threaded end first toward out-
side edge of Personal Back. Insert through first hole
ONLY.
INSTALLATION WARNINGS
The position of the Persona l Ba ck in the different
mounting bra cket slots is directly rela ted to the
cha ir's sta bility. When the Persona l Ba ck is a dded
to a TILT a nd/or RECLINING cha ir, it ma y ca use a
decrea se in the cha ir's sta bility. It ma y be neces-
sa ry to re position the FRONT CASTERS, REAR
WHEELS, BACK ANGLE, TILT-IN-SPACE, RECLINE PO-
SITION a nd/or SEAT DEPTH before use. Use EXTREME
ca ution when using a new sea ting position.
3. Slide the #10 flat washer (Item 6) onto the threaded
end from the inside of the Personal Back.
4. SlidetheUtilitySpring(Item5) ontotheLatchPinand
slidethreadsoftheLatchPinthroughremaininghole.
5. Temporarily screw the Nylon Locking Key (Item
2) onto the Latch Pin to prevent Latch Pin from
falling out of the Personal Back. DO NOT USE
LOCTITE YET.
Afte r ANY a djustme nts, re pa ir or se rvic e a nd BE-
FORE use , ma ke sure tha t a ll a tta c hing ha rdwa re
is tighte ne d se c ure ly.
6. Locate the groove on the Latch Pin.
INSTALLATION CAUTION
Whe n using LOCTITE 290, follow the ma nufa c -
ture rs' re c omme nda tions.
7. Push latch pin fully through Personal Back until
retaining groove is visible from inside Personal
Back.
USERWARNINGS
Skin c ondition should be c he c ke d fre que ntly
a fte r the insta lla tion of a ny ne w se a t.
8. This requires compressing the spring. Maintain
spring in compressed position to access groove.
9. Insert Retaining Ring (Item 4) into groove on Latch
Your thera pist a nd physicia n should be consulted
if you ha ve a ny que stions re ga rding individua l
limita tions a nd ne e ds.
Pin.
10. Release Latch Pin. It will be held in place by the
Retaining Ring.
Working with your the ra p ist, p hysic ia n, a nd
re ha bilita tion te c hnology supplie r is the be st
wa y to a ssure tha t a Pe rsona l Ba c k c hoic e
ma tc he s your individua l ne e ds.
As the ne e ds of the individua l be c ome more
c omple x, the Pe rsona l Ba c k e va lua tion be -
c ome s more importa nt.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
|