CONTENTS
Removing/Installing the Batteries.......................................................................................................................................................................................................39
Charging the Batteries..........................................................................................................................................................................................................................42
Installing/Removing the Crutch/Cane Holder.................................................................................................................................................................................47
Resetting the Circuit Breaker.............................................................................................................................................................................................................55
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1 GENERAL
1 General
1.1 Symbols
Warnings
Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage. See the
information below for definitions of the signal words.
DANGER
ƽ
Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
ƽ
Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
ƽ
Caution indicates a potentially hazardous situation which, if not avoided, may result in property damage or minor injury or
both.
IMPORTANT
!
Indicates a hazardous situation that could result in damage to property if it is not avoided.
Gives useful tips, recommendations and information for efficient, trouble-free use.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1 GENERAL
1.2 Limited Warranty
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW
APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser/user of our products.
This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.
Invacare warrants all electronics and electrical components (excluding batteries), transaxle and frame to be free from defects in materials and workmanship
for a period of twelve (12) months from the date of purchase from Invacare or a dealer. Invacare warrants all batteries to be free from defects in materials
and workmanship for a period of six (6) months from the date of purchase from Invacare or a dealer. If within such warranty period any such product shall
be proven to be defective, such product shall be repaired or replaced at Invacare's option. This warranty does not include any labor or shipping charges
incurred in replacement part installation or repair of any such product. Invacare’s sole obligation and your exclusive remedy under this warranty shall be
limited to such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your Invacare product. In the event you do not receive satisfactory warranty
service, please write directly to Invacare at the address on the bottom of the back cover. Provide dealer's name address, date of purchase, indicate nature of
the defect and, if the product is serialized, indicate the serial number. Do not return products to our factory without our prior consent.
LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL
NUMBER HAS BEEN REMOVED OR DEFACED, PRODUCTS SUBJECT TO NEGLIGENCE, ACCIDENT, IMPROPER OPERATION, MAINTENANCE
OR STORAGE, COMMERCIAL OR INSTITUTIONAL USE, PRODUCTS MODIFIED WITHOUT INVACARE'S EXPRESS WRITTEN CONSENT
INCLUDING, BUT NOT LIMITED TO, MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS; PRODUCTS
DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE, OR TO A PRODUCT
DAMAGED BY CIRCUMSTANCES BEYOND INVACARE'S CONTROL, AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE.
THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE TO THESE INSTRUCTIONS. A
CHANGE IN OPERATING NOISE, PARTICULARLY RELATIVE TO MOTORS AND GEARBOXES DOES NOT CONSTITUTE A FAILURE. ALL SUCH
DEVICES WILL EXHIBIT A CHANGE IN OPERATING NOISE DUE TO AGING.
THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES WHATSOEVER, WHETHER EXPRESS OR
IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND THE SOLE
REMEDY FOR VIOLATIONS OF ANY WARRANTY WHATSOEVER, SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE
PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN, THE APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT
EXTEND BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN. INVACARE SHALL NOT BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/PROVINCIAL LAWS AND REQUIREMENTS.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2 SAFETY
2 Safety
The Safety section contains important information for the safe operation and use of this product.
2.1 General Guidelines
WARNING
ƽ
DO NOT use this product or any available optional equipment without first completely reading and understanding these
instructions and any additional instructional material such as owner’s manuals, service manuals or instruction sheets
supplied with this product or optional equipment. If you are unable to understand the warnings, cautions or instructions,
contact a healthcare professional, dealer or technical personnel before attempting to use this equipment - otherwise, injury
or damage may occur.
Procedures other than those described in this manual must be performed by a qualified technician.
ACCESSORIES WARNINGS
Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories. Accessories
designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare
products.
ƽ
DO NOT connect any medical devices such as ventilators, life support machines, etc., to the battery. This could cause
unexpected failure of the device and the powered scooter.
NOTICE
!
THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
Check all parts for shipping damage and test before using. In case of damage, DO NOT use. Contact Invacare/Carrier for
further instruction.
As a manufacturer of powered scooters, Invacare endeavors to supply a wide variety of powered scooters to meet many
needs of the end user. However, final selection of the type of powered scooter to be used by an individual rests solely with
the user and his/her healthcare professional capable of making such a selection.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2 SAFETY
2.2 Operation Information
Setup
WARNING
ƽ
Before using the scooter, verify that the motor is plugged into the harness.
Transport
WARNING
DO NOT operate on roads, streets or highways.
TIE-DOWN RESTRAINTS AND SEAT RESTRAINTS
ƽ
Powered scooter users should NOT be transported in vehicles of any kind while in the powered scooter. As of this date,
the Department of Transportation has not approved any tie-down systems for transportation of a user while in a powered
scooter, in a moving vehicle of any type.
It is Invacare’s position that users of powered scooters should be transferred into appropriate seating in vehicles for
transportation and use be made of the restraints made available by the auto industry. Invacare cannot and does not
recommend any powered scooter transportation systems.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2 SAFETY
WARNING
STAIRWAYS AND ESCALATORS
DO NOT attempt to move an occupied powered scooter between floors using a stairway. Use an elevator to move an
occupied powered scooter between floors.
ƽ
If moving a powered scooter between floors by means of a stairway, the occupant MUST be removed and transported
independently of the powered scooter. Extreme caution is advised when moving an unoccupied powered scooter up or
down the stairs. Invacare recommends disassembling the scooter and transporting the components independently up or
down the stairs. ONLY use secure, non-detachable parts on each component for hand-hold supports.
DO NOT attempt to lift the powered scooter by any removable (detachable) parts. Lifting by means of any removable
(detachable) parts of a powered scooter may result in injury to the user or damage to the powered scooter.
DO NOT use an escalator to move a powered scooter between floors. Serious bodily injury may occur.
Powered scooter with batteries and seat weighs between 103 and 112 lbs. Powered scooter without the batteries can
weigh between 80 and 89 lbs. Use proper lifting techniques (lift with your legs) to avoid injury.
DO NOT attempt to lift the powered scooter by its tiller, seat or shrouds.
If scooter is exposed to extreme temperature (above 100°F or below 32°F), high humidity and/or becomes wet, prior to
use, ensure handgrips DO NOT twist on scooter handles. Otherwise, damage or injury may occur.
Follow this procedure for moving the powered scooter between floors when an elevator is not available:
1. Remove the occupant from the powered scooter.
2. Disassemble the scooter. Refer to Transporting the Scooter on page 34.
3. Carefully move the powered scooter components up or down the stairway.
4. Once all the components of the scooter are transported to the desired location reassemble the scooter. Refer to Transporting the Scooter on
page 34.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2 SAFETY
Repair or Service Information
WARNING
ƽ
Scooters should be examined during maintenance for signs of corrosion (water exposure, incontinence, etc.). Electrical
components damaged by corrosion should be replaced IMMEDIATELY.
Set-up of the Electronics Control Unit is to be performed only by a qualified technician. The final adjustments of the
controller may affect other activities of the scooter. Damage to the equipment could occur if improperly set-up or
adjusted.
DO NOT service or adjust your powered scooter while occupied, unless otherwise noted.
DO NOT overtighten hardware attaching to the frame. This could cause damage to the frame tubing.
Safety/Handling of Powered Scooters
“Safety and Handling” of the powered scooter requires the close attention of the user. This manual points out the most common procedures and
techniques involved in the safe operation and maintenance. It is important to practice and master these safe techniques until you are comfortable in
maneuvering the powered scooter.
Use this information only as a “basic” guide. The techniques that are discussed have been used successfully by many. Individual users often develop
skills to deal with daily living activities that may differ from those described in this manual. Invacare recognizes and encourages each individual to try
what works best for him/her in overcoming obstacles that they may encounter; however, all warnings and cautions given in this manual MUST be
followed. Techniques in this manual are a starting point for the new powered scooter user with “safety” as the most important consideration for all.
WARNING
ƽ
DO NOT make sharp turns in the forward or reverse direction at excessive speed. Failure to observe the warning can
cause the scooter to tip over and may result in injury to user and/or damage to the product.
ALWAYS wear your seat positioning strap. Inasmuch as the seat positioning strap is an option on this scooter (you may
order with or without the seat positioning strap), Invacare strongly recommends ordering the seat positioning strap as an
additional safeguard for the scooter user. The seat positioning strap is a positioning strap only. It is not designed for use as
a safety device withstanding high stress loads such as auto or aircraft safety belts. If signs of wear appear, strap must be
replaced immediately.
DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching
between your knees.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2 SAFETY
To assure stability and proper operation of your powered scooter, you MUST, at all times, maintain proper balance. Your powered scooter has been
designed to remain upright and stable during normal daily activities.
Many activities require the scooter owner to reach, bend and transfer in and out of the powered scooter. These movements cause a change to the
normal balance, the center of gravity, and the weight distribution of the powered scooter. To determine and establish your particular safety limits,
practice bending, reaching and transferring activities in several combinations in the presence of a qualified healthcare professional before attempting
active use of the scooter. Proper positioning is essential for your safety.
WARNING
DO NOT stand on the frame of the powered scooter while driving.
DO NOT stand on the shroud(s) of the powered scooter.
ƽ
DO NOT lean over the top of the back upholstery to reach objects behind you, as this may cause the powered scooter to
tip over.
DO NOT shift your weight or sitting position toward the direction you are reaching as the powered scooter may tip over.
Determine and establish your particular safety limits by practicing bending, reaching and transferring activities in the
presence of a qualified healthcare professional before attempting active use of the powered scooter.
For individuals with balance problems, DO NOT attempt to transfer into or out of the powered scooter without
assistance. Practice transferring activities with an assistant in the presence of a qualified healthcare professional.
Performance adjustments should only be made by professionals of the healthcare field or persons fully conversant with this
process and the driver's capabilities. Incorrect settings could cause injury to the driver, bystanders and damage to the
scooter and to surrounding property.
DO NOT operate the powered scooter until you have checked that the surroundings are clear and that the area is safe for
travel.
DO NOT operate on roads, streets or highways.
DO NOT attempt to move up or down an incline with water, ice or oil film.
Avoid operating the scooter in dark or poorly lit areas.
DO NOT climb and/or go up or down ramps or traverse slopes greater than 8°.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2 SAFETY
WARNING
ƽ
When negotiating ramps, if the throttle control lever is released while in the forward motion, the powered scooter will roll
back approximately one foot before the brake engages. If the throttle control lever is released while in the reverse motion,
the powered scooter will roll back approximately three feet before the brake engages.
DO NOT attempt to drive over curbs or obstacles. Doing so may cause your powered scooter to turn over and cause
bodily harm and/or damage to the scooter.
Before attempting to sit in or exit the powered scooter, remove the key from the ignition. This will ensure that the power
is off and the powered scooter will not drive.
DO NOT remove the key or shut off while the powered scooter is in motion.
DO NOT operate the powered scooter without the rear shroud installed, to avoid injury and/or damage to scooter.
Ensure that the seat is properly locked before use. Otherwise the user may fall from the scooter resulting in bodily harm.
Attempting unsafe transfers may cause the user to fall, resulting in serious injury.
Ensure that the seat is locked in the forward position before and during the operation of the scooter. Otherwise, injury to
the user and/or damage to the scooter may result.
Ensure that the tiller is properly adjusted before driving the scooter.
After making any tiller angle adjustment and before use, the tiller must be securely locked into position. Otherwise the user
may fall from the scooter resulting in bodily harm and/or damage to the scooter. Gently push/pull the tiller to ensure that
the tiller is securely engaged.
ALWAYS keep hands and fingers clear of moving parts to avoid injury.
ALWAYS check hand grips for looseness before using the powered scooter. If loose and/or worn, replace immediately.
Never leave an unoccupied scooter on an incline.
ALWAYS use anti-tippers. When outdoors on wet, soft ground or on gravel surfaces,
anti-tippers may not provide the same level of protection against tip over. Extra caution MUST be observed when
traversing such surfaces.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2 SAFETY
Storage
WARNING
ƽ
Scooters that are used by incontinent users and/or are frequently exposed to water may require replacement of electrical
components more frequently.
RAIN TEST
Invacare has tested its powered scooters in accordance with ISO 7176 “Rain Test”. This provides the end user or his/her
attendant sufficient time to remove his/her powered scooter from a rain storm and retain powered scooter operation.
DO NOT leave the powered scooter in a rain storm of any kind.
DO NOT use the powered scooter in a shower.
DO NOT leave the powered scooter in a damp area for any length of time.
Direct exposure to rain or dampness will cause the scooter to malfunction electrically and mechanically; may cause the
powered scooter to prematurely rust.
Check to ensure that all electrical connections are secure at all times.
Remove the key from the ignition while the powered scooter is not in use so as to avoid injury and/or damage to the
scooter and surrounding areas.
Avoid storing or using the scooter near open flame or combustible products. Serious injury or damage to property may
result.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2 SAFETY
Electrical and Grounding
WARNING
Check to ensure that all electrical connections are secure at all times.
GROUNDING INSTRUCTIONS
Ꮨ
DO NOT, under any circumstances, cut or remove the round grounding prong from any plug used with or for Invacare
products. Some devices are equipped with three-prong (grounding) plugs for protection against possible shock hazards.
Where a two-prong wall receptacle is encountered, it is the personal responsibility and obligation of the customer to
contact a qualified electrician and have the two-prong receptacle replaced with a properly grounded three-prong wall
receptacle in accordance with the National Electrical Code. If you must use an extension cord, use ONLY a three-wire
extension cord having the same or higher electrical rating as the device being connected. In addition, Invacare has placed
RED/ORANGE warning tags on some equipment. DO NOT remove these tags.
Battery
WARNING
ƽ
The warranty and performance specifications contained in this manual are based on the use of deep cycle gel cell batteries.
Invacare strongly recommends their use as the power source for this unit.
Carefully read battery/battery charger information prior to installing, servicing or operating your powered scooter.
Weight Training
WARNING
ƽ
Invacare DOES NOT recommend the use of its powered scooters as a weight training apparatus. Invacare powered
scooters have NOT been designed or tested as a seat for any kind of weight training. If occupant uses said powered
scooter as a weight training apparatus, Invacare shall NOT be liable for bodily injury and the warranty is void.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2 SAFETY
Weight Limitation
WARNING
The weight limitation is 300 lbs.
ƽ
Disposal
WARNING
This product has been supplied from an environmentally aware manufacturer that complies with the Waste Electrical and
Electronic Equipment (WEEE) Directive 2002/96/CE.
This product may contain substances that could be harmful to the environment if disposed of in places (landfills) that are
not appropriate according to legislation.
Please be environmentally responsible and recycle this product through your recycling facility at its end of life.
2.1 EMI Information
CAUTION
ƽ
IT IS VERY IMPORTANT THAT YOU READ THIS INFORMATION REGARDING THE POSSIBLE EFFECTS OF
ELECTROMAGNETIC INTERFERENCE ON YOUR POWERED WHEELCHAIR.
Electromagnetic Interference (EMI) From Radio Wave Sources
Powered wheelchairs and motorized scooters (in this text, both will be referred to as powered wheelchairs) may be susceptible to electromagnetic
interference (EMI), which is interfering electromagnetic energy (EM) emitted from sources such as radio stations, TV stations, amateur radio (HAM)
transmitters, two way radios, and cellular phones. The interference (from radio wave sources) can cause the powered wheelchair to release its brakes,
move by itself, or move in unintended directions. It can also permanently damage the powered wheelchair's control system. The intensity of the
interfering EM energy can be measured in volts per meter (V/m). Each powered wheelchair can resist EMI up to a certain intensity. This is called its
“immunity level.” The higher the immunity level, the greater the protection. At this time, current technology is capable of achieving at least a 20 V/m
immunity level, which would provide useful protection from the more common sources of radiated EMI.
There are a number of sources of relatively intense electromagnetic fields in the everyday environment. Some of these sources are obvious and easy
to avoid. Others are not apparent and exposure is unavoidable. However, we believe that by following the warnings listed below, your risk to EMI
will be minimized.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
2 SAFETY
The sources of radiated EMI can be broadly classified into three types:
1. Hand-held Portable transceivers (transmitters-receivers with the antenna mounted directly on the transmitting unit. Examples include: citizens
band (CB) radios, “walkie talkie”, security, fire and police transceivers, cellular telephones, and other personal communication devices).
Some cellular telephones and similar devices transmit signals while they are ON, even when not being used.
2. Medium-range mobile transceivers, such as those used in police cars, fire trucks, ambulances and taxis. These usually have the antenna mounted
on the outside of the vehicle; and
3. Long-range transmitters and transceivers, such as commercial broadcast transmitters (radio and TV broadcast antenna towers) and amateur
(HAM) radios.
Other types of hand-held devices, such as cordless phones, laptop computers, AM/FM radios, TV sets, CD players, cassette
players, and small appliances, such as electric shavers and hair dryers, so far as we know, are not likely to cause EMI
problems to your powered wheelchair.
Powered Wheelchair Electromagnetic Interference (EMI)
Because EM energy rapidly becomes more intense as one moves closer to the transmitting antenna (source), the EM fields from hand-held radio wave
sources (transceivers) are of special concern. It is possible to unintentionally bring high levels of EM energy very close to the powered wheelchair's
control system while using these devices. This can affect powered wheelchair movement and braking. Therefore, the warnings listed below are
recommended to prevent possible interference with the control system of the powered wheelchair.
Electromagnetic interference (EMI) from sources such as radio and TV stations, amateur radio (HAM) transmitters, two-way radios, and cellular
phones can affect powered wheelchairs and motorized scooters.
FOLLOWING THE WARNINGS LISTED BELOW SHOULD REDUCE THE CHANCE OF UNINTENDED BRAKE RELEASE OR POWERED
WHEELCHAIR MOVEMENT WHICH COULD RESULT IN SERIOUS INJURY.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2 SAFETY
WARNING
ƽ
1) DO NOT operate hand-held transceivers (transmitters receivers), such as citizens band (CB) radios, or turn ON
personal communication devices, such as cellular phones, while the powered wheelchair is turned ON;
2) Be aware of nearby transmitters, such as radio or TV stations, and try to avoid coming close to them;
3) If unintended movement or brake release occurs, turn the powered wheelchair OFF as soon as it is safe;
4) Be aware that adding accessories or components, or modifying the powered wheelchair, may make it more
susceptible to EMI (NOTE: There is no easy way to evaluate their effect on the overall immunity of the powered
wheelchair); and
5) Report all incidents of unintended movement or brake release to the powered wheelchair manufacturer, and
note whether there is a source of EMI nearby.
Important Information
1) 20 volts per meter (V/m) is a generally achievable and useful immunity level against EMI (as of May 1994) (the
higher the level, the greater the protection);
2) This device has been tested to a radiated immunity level of 20 volts per meter.
3) The immunity level of the product is unknown.
Modification of any kind to the electronics of this scooter as manufactured by Invacare may adversely affect the EMI
immunity levels.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3 PRODUCT LABELING
3 Product Labeling
Lynx L-3 shown. The labels are in the same locations for the Lynx L-4.
! WARNING
Pinch Point.
1079203
Serial
Number
Label
DO NOT operate the scooter unless the tiller is in the locked position.
DO NOT lean against or pull forward on the tiller while mounting or
dismounting the scooter. Otherwise, injury may occur.
--------------------------------------------------------------------------------------------
DO NOT lift scooter up by the front or rear shroud. Otherwise injury
or damage to the scooter may occur.
1118373 Rev A
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3 PRODUCT LABELING
The battery wiring label is on the underside of
the battery box door.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4 TECHNICAL DATA
4 Technical Data
4.1 Typical Product Parameters
Overall Dimensions
LYNX L-3
LYNX L-4
Base Length:
39.8 in
26 in
Base Width:
Step Height (Floor Pan to Ground):
Seat Height (Floor Pan to Seat Cushion):
Overall Height:
4 in
14 - 16 in
36 in
Seat Dimensions
LYNX L-3
LYNX L-4
LYNX L-4
Width:
18 in
16 in
15 in
Depth:
Back Height:
Arm Dimensions
LYNX L-3
Length:
11.6 in
9 in
Height between Seat and Arms:
Minimum Width Between Arms:
15.0 in
19
Download from Www.Somanuals.com. All Manuals Search And Download.
4 TECHNICAL DATA
Wheels
LYNX L-3
LYNX L-4
Front Wheel:
Drive Wheel:
8 in x 2 in
8 in x 2 in
Driving
LYNX L-3
LYNX L-4
Speed Range:
0 - 5 mph
8° Grade
Maximum Incline Capability:
Turning Radius:
39.4 in
51.2 in
Weight
LYNX L-3
30 lbs
LYNX L-4
39 lbs
Front Base Section:
Rear Base Section:
Batteries:
25 lbs
25 lbs
23 lbs
23 lbs
Seat:
19 lbs
19 lbs
Basket:
1 lb
1 lb
Total Weight of Product:
Maximum Weight Limitation:
98 lbs
107 lbs
300 lbs
300 lbs
20
Download from Www.Somanuals.com. All Manuals Search And Download.
5 INSPECTION
5 Inspection
5.1 Safety Inspection Checklists
Every six months take your powered scooter to a qualified technician for a thorough inspection and servicing. Regular
cleaning will reveal loose or worn parts and enhance the smooth operation of your powered scooter. To operate properly
and safely, your powered scooter must be cared for just like any other vehicle. Routine maintenance will extend the life and
efficiency of your powered scooter.
WARNING
ƽ
Before performing any maintenance, adjustment or service, turn power Off and remove key from ignition.
CAUTION
As with any vehicle, the wheels and tires should be checked periodically for cracks and wear, and should be replaced.
Initial adjustments should be made to suit your personal body structure needs and preference. Thereafter follow these maintenance procedures:
21
Download from Www.Somanuals.com. All Manuals Search And Download.
5 INSPECTION
Inspect/Adjust Initially
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
Ensure powered scooter drives straight (no excessive drag or pull to one side).
Check frame for damage and corrosion.
Ensure that the brake release lever is easy to engage/disengage.
Ensure that tiller adjustment mechanism engages and disengages properly and securely.
Ensure that the scooter stops completely when throttle is released (i.e., does not continue to roll as if the throttle is activated).
Clean upholstery and armrests.
Ensure armrest pad sits flush against arm tube.
Inspect the seat upholstery for rips and tears.
Inspect seat swivel for release and engagement (seat locks into the determined swivel positions).
Inspect for excessive side movement or binding when the drive wheels are raised or turned.
Inspect front wheel/fork assembly for proper tension by spinning the wheel. The front wheel should come to a gradual stop.
Check the front fork for damage or corrosion.
Tighten locknut if the front wheel wobbles noticeably or loosen locknut if the wheel binds to a stop.
Ensure that wheel bearings are clean and free of moisture.
Ensure that the bolts and fasteners on the caster assemblies are tight.
Inspect tires for flat spots and wear.
Clean molded body shrouds.
Check that all labels are present and legible.
Inspect/Adjust Weekly
❑
❑
❑
Ensure that tiller adjustment mechanism engages and disengages properly and securely.
Ensure that the scooter stops completely when throttle is released (i.e., does not continue to roll as if the throttle is activated).
Inspect tires for flat spots and wear.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
5 INSPECTION
Inspect/Adjust Monthly
❑
❑
❑
❑
❑
Check brake for binding or interference with travel.
Inspect front wheel/fork assembly for proper tension by spinning the wheel. The front wheel should come to a gradual stop.
Tighten locknut if the front wheel wobbles noticeably or loosen locknut if the wheel binds to a stop.
Inspect seat swivel for release and engagement (seat locks into the determined swivel positions).
Inspect the seat positioning strap for signs of wear. Replace if worn or damaged. Ensure buckle latches. Verify that the hardware that attaches
the seat positioning strap to the frame is secure and undamaged. Replace if necessary.
❑
Ensure that the bolts and fasteners on the caster assemblies are tight.
Inspect/Adjust Periodically
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
Ensure that the powered scooter drives straight (no excessive drag or pull to one side).
Check frame for damage and corrosion.
Ensure that the brake release lever is easy to engage/disengage.
Inspect for no excessive side movement or binding when the drive wheels are raised or turned.
Check front fork for damage or corrosion.
Ensure wheel bearings are clean and free of moisture.
Clean upholstery and armrests.
Inspect the seat upholstery for rips and tears.
Ensure armrest pad sits flush against arm tube.
Check that all labels are present and legible.
Inspect electrical components for signs of corrosion. Replace if corroded or damaged.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
6 OPERATING THE POWERED SCOOTER
6 Operating the Powered Scooter
6.1 Control Panel
1. Speed Control Knob - The speed control knob is located on the right side of the control panel. The Turtle icon represents the slowest speed
and the Rabbit icon represents the fastest speed.
2. Battery Charge Display - The battery charge display is located at the top center of the control panel. When the scooter is turned on, the needle
on the battery charge display will move to the right to indicate the amount of battery charge. The amount of battery charge is indicated by the
colors on the display. If the charge is full, the needle will be to the right, in the GREEN area. As the battery charge decreases, the needle moves,
from right to left. When the needle is in the YELLOW area, the batteries are draining and should be charged soon. When the needle is to the
far left in the RED area, charge the batteries immediately. If the needle does not move when the scooter is turned on, the batteries should be
charged as soon as possible.
WARNING
ƽ
When negotiating ramps, if the throttle control lever is released while in forward motion, the powered scooter will roll
back approximately one foot before brake engages. If the throttle control lever is released while in reverse motion the
powered scooter will roll back approximately three feet before brake engages.
3. Key - The key is just below the control panel. Turn the key:
•
•
To the Left - Turn the scooter off.
To the Right - Turn the scooter on.
4. Horn Button - The horn button is located on left side of the control panel.
5. Throttle Control Lever - The throttle control lever is located in front of the handles on the tiller assembly.
6. Service Indicator - The service indicator will flash if there is a problem with the scooter. The number of flashes indicates the type of error. Refer
24
Download from Www.Somanuals.com. All Manuals Search And Download.
6 OPERATING THE POWERED SCOOTER
Battery Charge Display
Horn Button
Key
Service Indicator
Speed Control Knob
Throttle Control Lever
6.2 Operating the Scooter
WARNING
ƽ
After any adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely -
otherwise injury or damage may result.
DO NOT make sharp turns in the forward or reverse direction at excessive speed. Failure to observe the warning can
cause the scooter to tip over and may result in injury to user and/ or damage to the product.
To determine and establish your particular safety limits, practice bending, reaching and transferring activities in several
combinations in the presence of a qualified healthcare professional before attempting active use of the powered scooter.
Ensure seat is properly locked before attempting transfer into or out of the powered scooter. Attempting unsafe transfers
may cause a fall from the powered scooter resulting in bodily injury.
For individuals with balance problems, practice transferring activities with an assistant in the presence of a qualified
healthcare professional. DO NOT attempt to transfer into or out of the powered scooter without assistance.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
6 OPERATING THE POWERED SCOOTER
4. Transferring to and from the seat can be accomplished in one of two ways:
•
•
Flipping up the armrest makes entering/exiting easier.
Rotating seat to the direction of transfer. Refer to Adjusting 90° Seat Swivel on page 31.
5. Once you have transferred into the seat, rotate seat to the forward position and flip arms down.
7. Adjust speed control knob to the appropriate setting.
For driving indoors or on uneven terrain, a slower speed is recommended. For soft terrain or steep inclines (no greater
than 8°), a faster speed may be necessary.
8. Insert the key into the ignition and turn it to the on position.
WARNING
ƽ
ALWAYS depress the throttle control lever gradually. This will ensure smooth safe starts.
Throttle control levers operate such that moving one will also move the opposite side throttle control lever.
9. To operate the scooter, depress the throttle control lever in the following manner:
•
•
•
To Move Forward - Push the right side throttle control lever (away from the user) or pull the left side throttle control lever towards the
user).
To Move in Reverse - Push the left side throttle control lever (away from the user) or pull the right side throttle control lever (towards the
user).
To Stop - Release the throttle control lever and the powered scooter will quickly slow down and the brake will engage.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
6 OPERATING THE POWERED SCOOTER
To equip the scooter for left hand operation, contact a qualified technician.
The powered scooter is equipped with a “proportional” control meaning that the farther you depress the throttle control lever, the faster the
powered scooter travels. With a proportional control, you can drive as slowly in the high speed setting as you can in the low speed setting. Your top
speed, however, is limited by the setting of the speed-control knob. For safety reasons, reverse speed is limited to approximately 50% of forward
speed.
When first learning to drive, adjust speed control knob for a slow speed and try to drive the powered scooter as slowly as possible by depressing the
throttle control lever only slightly. This exercise will help you learn to utilize the full potential of the proportional control and allow you to start and
stop smoothly.
6.3 Engaging/Disengaging the Brake Release Lever
WARNING
ƽ
Ensure that the brake-release lever is in the engaged position before driving. There should be an audible “click” when
stopping and starting the scooter.
Lynx L-3 shown. Lynx L-4 brake release lever is in the same location.
The brake release lever manually engages and disengages the brake. The brake release lever is located under the seat on the right side.
The brake must be engaged in normal driving conditions. Activation of the throttle control lever automatically releases the brake so that the powered
scooter can drive. Releasing the throttle control lever automatically engages the brake so as to prevent the powered scooter from rolling on its own.
When the brake release lever is disengaged and the key is removed, the powered scooter can be pushed. The powered scooter cannot be driven with
the brake in the disengaged position.
1. To engage the brake release lever (Drive) - Pull back the brake release lever.
2. To disengage the brake release lever (Push) - Push forward the brake release lever.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
7 SEAT AND ARMS
7 Seat and Arms
WARNING
ƽ
After any adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely -
otherwise injury or damage may result.
Before performing any maintenance, adjustment or service, turn power off and remove key from ignition.
Refer to Label Locations on page 9 for pinch point location.
7.1 Removing/Installing the Seat
WARNING
ƽ
Before use, ensure that the seat is in the locked position. The seat lever MUST be pulled up to the 90° position to allow the
seat to drop into the locked position. Otherwise, a fall from the scooter could occur causing bodily injury and/or damage to
the scooter.
Removing
1. Fold down seat back.
2. Pull up the seat lock lever.
3. Lift the seat assembly up and away from the seat post.
Seat
Assembly
Installing
1. Lower the seat assembly onto the seat post.
2. Pull the seat lock lever up to allow the seat to drop into the locked
position.
Seat Lock
Lever
3. Lift up on seat assembly to ensure the seat is secure.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
7 SEAT AND ARMS
7.2 Adjusting Seat Height
Knob removed for clarity. The knob does not
have to be removed to perform this procedure.
3. Loosen the knob on the frame tube.
4. Remove the locking pin that secures the seat post to the frame
tube.
5. Align the frame tube mounting hole with one of three seat post
mounting holes to achieve desired seat height.
Seat Post
WARNING
Mounting
Holes
Locking Pin
Knob
ƽ
Make sure the detent balls of the locking pin are
fully released beyond the outer edge of the frame
tube before operating the scooter. Otherwise,
injury and/or damage may result.
Keep detent balls clean.
Frame Tube
6. Insert the locking pin through the frame tube and seat post. Ensure
the detent balls (not shown) of the locking pin are beyond the outer
edge of the frame tube and the pin secures the frame tube to the
seat post.
Frame Tube
Mounting Hole
7. Tighten the knob until the seat post does not move around inside
of the frame tube.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
7 SEAT AND ARMS
7.3
Adjusting 90° Seat Swivel
Top View
WARNING
ƽ
Ensure that seat is locked into the forward position
before and during operation of the scooter.
Otherwise, injury to the user and/or damage to the
scooter may result.
Seat
CAUTION
Use the seat swivel option with caution when
accessories are installed (such as safety flag, crutch/
cane holder, etc.). Otherwise, damage to the
scooter or property may occur.
1. Pull up the seat lock lever to unlock the seat.
View From Back
2. Rotate the seat to the desired position.
3. Release the seat lock lever to lock the seat in the desired position.
Seat
Ensure that the seat is locked in the forward facing
position before operating the scooter.
Seat Lock
Lever
31
Download from Www.Somanuals.com. All Manuals Search And Download.
7 SEAT AND ARMS
7.4 Adjusting the Arm Width
Lynx L-3 shown. Lynx L-4 adjusts the same way.
When installing the arms during set up, the four
mounting screws are installed on the seat hinge for
shipping purposes.
Arm
Arm
1. Loosen the knob securing the arm tube to the seat frame.
2. Push the arm in or out to the desired position.
Tube
Seat
Frame
Knob
7.5 Replacing Armrest Pads
1. Remove the two mounting screws that secure the armrest pad to
Arm Pad
Arm
arm.
2. Remove the old armrest pad.
3. Install new armrest pad and securely tighten with existing mounting
screws.
4. If necessary, repeat STEPS 1-3 to replace the other armrest pad.
Mounting
32
Download from Www.Somanuals.com. All Manuals Search And Download.
8 TILLER ADJUSTMENT
8 Tiller Adjustment
8.1 Adjusting the Tiller Angle
WARNING
ƽ
Before performing any maintenance, adjustment or service, turn power Off and remove key from ignition.
Ensure that tiller is properly adjusted before driving the scooter.
After making any tiller angle adjustments and before use, the tiller MUST be securely locked into position. Otherwise, a fall
from the scooter could occur causing bodily injury and/or damage to the scooter. Gently, push/pull against tiller to ensure
that the tiller is securely engaged into the adjustment plate.
DETAIL “A”
Tiller Adjustment Lever
Tiller Assembly
The powered scooters feature an adjustable tiller.
The tiller locks into one of three positions. The
tiller can also be folded down for transportation
and storage.
Mounting Hole
Pin
1. Rotate or pull out the tiller adjustment lever (Detail “A”) until the
pin disengages from the mounting hole.
2. Move the tiller to the desired position.
3. Release or rotate the tiller adjustment lever to lock the pin into the
desired mounting hole (Detail “A”).
4. Gently push/pull against tiller to ensure that the tiller is securely
locked.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
9 WHEELS AND CASTERS
9 Wheels and Casters
WARNING
ƽ
After any adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely -
otherwise injury or damage may result.
Before performing any maintenance, adjustment or service, turn power Off and remove key from ignition.
9.1 Removing/Installing the Drive Wheels
This procedure applies to the rear wheels on the Lynx L-3 and all wheels on the Lynx L-4.
Removing
1. Turn power off and remove the key from the ignition.
*The keystock is not present on the front wheels
of the Lynx L-4 scooters.
2. Remove the seat. Refer to Removing/Installing the Seat on page 23.
3. Place the rear frame assembly (not shown) up on blocks so that the
drive wheels are off the ground.
4. Remove the washer and mounting screw that secure the drive
wheel to the drive shaft.
Keystock*
Drive Wheel
5. Remove the existing drive wheel assembly from the drive shaft.
Washer
Use a wheel puller if necessary to remove the
Drive Shaft
6. Remove keystock from drive shaft. Set aside.
Mounting Screw
wheel from the drive shaft.
7. If necessary, repeat STEPS 1-7 to remove other drive wheel.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
9 WHEELS AND CASTERS
Installing
* The keystock is not present on the front wheels of the Lynx L-4 scooters.
The keystock in the drive shaft MUST lineup with the cutout in the wheel hub.
If necessary, use a rubber hammer to gently tap drive wheel completely into position on the drive shaft.
2. Install the drive wheel onto the drive shaft.
3. Secure wheel to drive shaft using the mounting screw and washer. Securely tighten.
4. Repeat STEPS 1-3 to install the other drive wheel.
5. Install the seat. Refer to Removing/Installing the Seat on page 23.
9.2 Removing/Installing the Front Wheel
This procedure applies to the Lynx L-3 only.
Take note of position and orientation of wheel and mounting hardware before removing.
Removing
Fork
Fork
Mounting
Hole
Fork
Mounting
Hole
1. Turn power off and remove the key from the ignition.
2. Place the front of the powered scooter up on blocks so that the
front wheel is off the ground.
3. Remove the mounting screw, locknut, two spacers and washer that
secure the front wheel to the fork.
4. Remove the front wheel from the fork.
Locknut
Front
Wheel
Washer
Installing
Mounting
Screw
1. Align the front wheel with the fork mounting holes.
2. Using the mounting screw, locknut, two spacers and washer, secure
the front wheel to the fork.
Spacer
Spacer
3. Securely tighten the front wheel mounting hardware.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
10 BATTERIES
10 Batteries
WARNING
ƽ
Before performing any maintenance adjustment or service, turn power off and remove key from ignition.
NEVER allow any of your tools and/or battery cables to contact both battery terminals at the same time. An electrical short
may occur and serious personal injury or damage may occur.
The use of rubber gloves is recommended when working with batteries.
DO NOT tip the batteries. Keep the batteries in an upright position.
Invacare strongly recommends that battery installation and battery replacement always be done by a qualified technician.
All battery terminals caps (two on the left battery and two on the right battery) MUST be installed prior to use.
CAUTION
When connecting the battery cables to the batteries, the battery cables MUST be connected to the battery terminals/posts
as shown in FIGURE 10.3 - otherwise damage to the battery may result.
If there is battery acid in the bottom of the battery box or on the sides of the batteries, apply baking soda to these areas to
neutralize the battery acid. Before reinstalling the existing or new batteries, clean the baking soda from the battery tray or
batteries being sure to avoid contact with skin and eyes. Determine source of contamination. Never install/reinstall a
battery with a cracked or otherwise damaged case.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
10 BATTERIES
10.1 Recommended Battery Type
WARNING
ƽ
The warranty and performance specifications contained in this manual are based on the use of AGM batteries. Invacare
strongly recommends their use as the power source for this unit.
CAUTION
Failure to use the correct battery size and/or voltage may cause damage to the powered scooter and give unsatisfactory
performance.
The Lynx L-3 and Lynx L-4 powered scooters are designed to use two
12 volt, 12-Amp-hour (12 AH) batteries.
Recommended battery type is spill proof and requires no maintenance
except routine charging.
Charge batteries daily. DO NOT allow batteries to completely
discharge.
Invacare recommends that both batteries be replaced if one battery is
defective.
12 Volt, 12 Amp-Hour
(12AH) Battery
37
Download from Www.Somanuals.com. All Manuals Search And Download.
10 BATTERIES
10.2 Removing/Installing the Battery Box
The battery box is held in place with hook and loop strips.
Removing
1. Turn power off and remove the key from the ignition.
2. Remove the seat. Refer to Removing/Installing the Seat on page 23.
3. With one hand, push the release lever to the rear of the scooter.
4. With the other hand, hold the battery box handle and lift the battery box up and away from the scooter (Detail “A”).
Installing
1. Turn power off and remove the key from the ignition.
2. Remove the seat. Refer to Removing/Installing the Seat on page 23.
3. Holding the battery box handle, carefully lower the battery box on to the battery tray in the scooter (Detail “B”).
4. Press down the battery box to engage the connector on the battery box (not shown) with the connector on the scooter base (Detail “B”).
5. Reinstall the seat. Refer to Removing/Installing the Seat on page 23.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
10 BATTERIES
DETAIL “B”
DETAIL “A”
Battery Tray
Release Lever
Battery Box
Handle
Battery Box
Connector on Base
10.3 Removing/Installing the Batteries
Removing
1. Remove the seat. Refer to Removing/Installing the Seat on page 23.
2. Remove the battery box from the scooter. Refer to Removing/Installing the Battery Box on page 38.
3. Remove the twelve mounting screws (not shown) that secure the battery box top to the battery box (Detail “A” of FIGURE 10.3).
Mounting screws are located on the underside of the battery box.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
10 BATTERIES
4. Disconnect the wiring harness from the batteries by holding the connectors and pulling them in the following order (Detail “B” of FIGURE 10.3):
A. NEGATIVE (-) BLACK battery cable from the NEGATIVE (-) battery terminal on the left battery.
B. POSITIVE (+) RED battery cable from the POSITIVE (+) battery terminal on the right battery.
C. WHITE battery cable (Jumper) from the POSITIVE (+) battery terminal on the left battery and the NEGATIVE (-) battery terminal on the
right battery.
5. Remove the tape securing the thermal switch to the side of the left battery.
6. Remove the batteries from battery box by lifting the batteries out.
Installing
1. Install the two new batteries into the battery box.
2. Secure the thermal switch to the side of the left battery using tape.
The thermal switch needs to be well secured and in direct contact with the side of the battery. Service tape is available as a
service part and is the recommended solution. As an alternate, a heavy duty “duct” styled tape can be used. If “duct” styled
tape is used, wrapping the tape completely around the battery with minimal overlap will provide the best adhesion.
A. NEGATIVE (-) BLACK battery cable to the NEGATIVE (-) battery terminal on the left battery.
B. POSITIVE (+) RED battery cable to the POSITIVE (+) battery terminal on the right battery.
C. WHITE battery cable (Jumper) to the POSITIVE (+) battery terminal on the left battery and the NEGATIVE (-) battery terminal on the right
battery.
4. Replace the top of the battery box and secure with the twelve mounting screws (Detail “A” of FIGURE 10.3). Securely tighten.
5. Reinstall the battery box on to the scooter frame. Refer to Removing/Installing the Battery Box on page 38.
6. Reinstall the seat. Refer to Removing/Installing the Seat on page 23.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
10 BATTERIES
NEGATIVE (-) BLACK
Battery Cable
DETAIL “A”
DETAIL “B”
BatteryBox
Cover
BatteryBox
Cover
WHITE Battery Cable
(Jumper)
NEGATIVE (-)
BLACK Battery
Terminal
POSITIVE (+)
RED Battery
Terminal
Cablesto
Thermal
Switch
(not
shown)
POSITIVE (+)
RED Battery
Cable
Battery
Box
Right Battery
Battery
Left Battery
Box
41
Download from Www.Somanuals.com. All Manuals Search And Download.
10 BATTERIES
10.4 Charging the Batteries
WARNING
ƽ
NEVER attempt to recharge the batteries by attaching cables directly to the battery terminals or clamps.
DO NOT attempt to recharge the batteries and operate the powered scooter at the same time.
Only use the provided charger with this product.
If the circuit breaker trips repeatedly, IMMEDIATELY unplug charger and contact dealer or a qualified technician.
CAUTION
New batteries MUST be fully charged prior to initial use of the powered scooter.
DO NOT sit in the scooter while recharging the batteries.
ALWAYS charge new batteries before initial use or battery life will be reduced.
As a general rule, you should recharge your batteries as frequently as possible to assure the longest possible life and to
minimize required charging time. Plan to recharge them when you do not anticipate using the powered scooter.
The powered scooter is designed with an electrical lockout to prevent it from being driven while the charger is plugged into
an outlet.
Always charge the batteries completely until the battery charger light turns GREEN.
The range per battery charge using recommended batteries should be approximately five to nine hours of typical operation.
Extensive use on inclines may substantially reduce per charge mileage.
1. Turn the key to the Off position.
2. If desired, remove the battery box from the scooter. Refer to Removing/Installing the Battery Box on page 38.
3. Ensure the brake release lever is engaged. Refer to Engaging/Disengaging the Brake Release Lever on page 22.
4. Move the battery charger port cap (located on the left side of the battery box) to one side.
5. Remove the battery charger cable from the storage compartment on the front of the battery box.
6. Plug one end of the battery charger cable into the battery charger port located on the battery box.
7. Plug the other end of the battery charger cable into 110-volt wall outlet.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
10 BATTERIES
The battery charger light will be YELLOW or RED.
8. Allow the batteries to charge until the charger light turns GREEN.
9. Perform one of the following:
•
•
Battery charger light turns GREEN - Unplug the battery charger cable from the scooter and the wall outlet.
Battery charger light flashes GREEN for over 40 minutes - Perform the following steps:
i.
Check that the battery charger is correctly connected to the scooter and the wall outlet.
ii. Check that the scooter is turned off.
iii. If steps i and ii do not correct the problem, contact a qualified technician.
10. Unplug the battery charger from the wall outlet.
11. Unplug the battery charger from the scooter.
Battery Charger Indicator Light
Storage Compartment
Wall
Outlet
Battery Charger Port Cap
Battery
Charger Port
12. Store the battery charger cable in the storage compartment.
13. Move the battery charger port cap to cover the battery charger
port.
Battery Box
Battery
Charger
Cable
43
Download from Www.Somanuals.com. All Manuals Search And Download.
11 TRANSPORTING
11 Transporting
WARNING
ƽ
After any adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely -
otherwise injury or damage may result.
Before performing any maintenance, adjustment or service, turn power off and remove key from ignition.
DO NOT lift the scooter by the rear shroud - otherwise damage to the scooter may occur.
11.1 Transporting the Scooter
Disassembling
1. Turn power off and remove the key from the ignition.
2. Remove the basket.
3. Remove the seat. Refer to Removing/Installing the Seat on page 23.
5. Hold the seat post with one hand (Detail “A”).
6. With the other hand, push the release lever to the rear of the scooter.
7. Lift the seat post to separate the front frame assembly from the rear frame assembly (Detail “B”).
8. Fold tiller down to lowest locked position. Refer to Adjusting the Tiller Angle on page 26.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
11 TRANSPORTING
Assembling
1. Unfold tiller. Refer to Adjusting the Tiller Angle on page 26.
2. Tilt the rear frame back a little.
3. Hold the seat post and align the frame tubes on the front frame assembly with the mounting recesses on the rear frame assembly (Detail “B”).
4. While holding the seat post, slowly pivot the rear frame assembly forward until the release lever locks (Detail “A”).
6. Install the seat. Refer to Removing/Installing the Seat on page 23.
7. Install the basket.
DETAIL “A”
DETAIL “B”
Release
Lever
Front Frame
Assembly
Seat Post
Seat Post
Frame Tube
Frame Tube
Mounting
Recess
Mounting
Recess
Release
Lever
Rear Frame Assembly
(Slightly Tilted)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
12 ACCESSORIES
12 Accessories
WARNING
ƽ
After any adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely -
otherwise injury or damage may result.
Before performing any maintenance, adjustment or service, turn power off and remove key from ignition.
The crutch/cane holder, safety flag, rear mounted basket and oxygen holder all install into the accessory tubes; ONLY one
of these may be installed at a time.
12.1 Installing/Removing the Accessory Tube
Installing
Mounting Screw DETAIL “A”
Installs HERE
1. Position the accessory tube onto the seat frame.
2. Secure the accessory tube to the seat frame using the mounting
screw (Detail “A”).
Cap
3. Remove the mounting knob from the accessory tube.
4. Remove the cap from the accessory tube.
Removing
1. Remove the mounting screw securing the accessory tube to the
seat frame.
Mounting Knob
Accessory Tube Mounts
to the Seat Frame HERE
2. Remove the accessory tube from the seat frame.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
12 ACCESSORIES
12.2 Installing/Removing the Crutch/Cane Holder
WARNING
ƽ
The installation of the crutch/cane holder onto the back of the scooter seat significantly increases the length of the scooter.
When turning the scooter or swiveling the scooter seat, it is important to take note of this increased length - otherwise,
injury and/or damage to the surrounding property may result.
Installing
1. Install the crutch/cane holder into the accessory tube located on
the back of the seat.
Accessory Tube
2. Install the mounting knob to secure the crutch/cane holder in place.
Securely tighten.
Crutch Cane
Holder
3. Align the slot on the base with the hook on the crutch/cane holder
and slide base down into position.
Mounting Knob
Removing
1. Remove the crutch/cane holder from the accessory tube.
2. Remove the mounting knob that secures the crutch/cane holder in
place.
Hook
Base
Insert Into
Accessory Tube
3. Remove the crutch/cane holder from the accessory tube.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
12 ACCESSORIES
12.3 Installing/Removing the Safety Flag
WARNING
ƽ
The installation of the safety flag onto the back of the scooter seat significantly increases the length of the scooter. When
turning the scooter or swiveling the scooter seat, it is important to take note of this increased length - otherwise, injury
and/or damage to the surrounding property may result.
Installing
1. Install the bracket into the accessory tube located on the back of
the seat.
2. Install mounting knob to secure the bracket in place. Securely
tighten.
Mounting Knob
3. Install safety flag into bracket.
Accessory Tube
Removing
Safety Flag
1. Remove the safety flag from the bracket.
2. Remove the mounting knob that secures the bracket in place.
3. Remove the bracket from the accessory tube located on the back
of the seat.
Insert Into Accessory
Tube
Bracket
48
Download from Www.Somanuals.com. All Manuals Search And Download.
12 ACCESSORIES
12.4 Installing/Removing/Using the Walker Holder
WARNING
ƽ
After ANY adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely.
The installation of the walker holder onto the back of the scooter seat significantly increases the length of the scooter.
When turning the scooter or swiveling the scooter seat, it is important to take note of this increased length - otherwise,
injury and/or damage to the surrounding property may result.
Installing/Removing the Walker Holder
Reverse this procedure to remove the walker holder.
1. If necessary, loosen but DO NOT remove the mounting knob.
Walker Holder
2. Install the walker holder into the accessory tube.
3. Thread the mounting knob into the welded nut on the accessory
tube. Securely tighten.
Accessory
Tube
Hook
Using the Walker Holder
1. Fold walker. Refer to walker instructions.
Mounting
Knob
Walker MUST be folded before using walker
Hook and
Loop Strap
2. Hang folded walker on walker holder hooks.
3. Secure walker with hook and loop straps.
holder.
Insert Into
Accessory Tube
49
Download from Www.Somanuals.com. All Manuals Search And Download.
12 ACCESSORIES
12.5 Installing/Removing the Rear Mounted Basket
WARNING
ƽ
The rear mounted basket is rated for a maximum capacity of ten lbs.
After ANY adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely.
The installation of the basket and basket bracket onto the back of the scooter seat increases the length of the scooter.
When turning the scooter or swiveling the scooter seat, it is important to take note of this increased length - otherwise,
injury and/or damage to surrounding property may occur.
Installing
1. Loosen but DO NOT remove the mounting knob.
2. Install the basket bracket into the accessory tube.
Accessory
Tube
Mounting
Knob
3. Thread the mounting knob into the welded nut on the accessory
tube. Securely tighten.
4. Align the mounting clips on the bracket with the slots on the basket
and slide the basket down securely into position.
Rear Basket
Mounting Clips
Insert Into
Accessory
Tube
Removing
1. Remove the basket from the bracket.
2. Loosen the mounting knob.
3. Remove the basket bracket from the accessory tube.
4. Tighten the mounting knob.
Slots
Basket Bracket
50
Download from Www.Somanuals.com. All Manuals Search And Download.
13 MAINTENANCE
13 Maintenance
WARNING
ƽ
After any adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely -
otherwise, injury or damage may occur.
Before performing any maintenance, adjustment or service, turn power Off and remove key from ignition.
DO NOT overtighten hardware attaching to the frame. This could cause damage to the frame.
When storing scooter for prolonged periods of time, remove batteries. Refer to Removing/Installing the Battery Box on
page 30. After reinstallation, always recharge batteries before use. Refer to Charging the Batteries on page 32.
Use care in storage. DO NOT allow any metallic objects to contact the exposed terminals.
13.1 Suggested Maintenance Procedures
1. Before using the powered scooter, make sure all nuts and bolts are tight. Check any parts for damage or wear and replace. Check all parts for
proper adjustment.
2. Ensure that batteries are properly maintained and charged as required.
3. The wheels and tires should be checked periodically for cracks and wear, and should be replaced by a qualified technician.
4. Regularly check for loose nuts and/or bolts in the front and drive wheels. If loose, have them adjusted by a qualified technician.
5. Clean dirt, dust and grease from exposed components.
6. Periodically have the bearings of the front wheel checked to make sure they are clean and free from moisture.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
14 TROUBLESHOOTING
14 Troubleshooting
14.1 General Troubleshooting
SYMPTOM
PROBABLE CAUSE
SOLUTION
Limited Driving Distance.
Battery not charged long enough.
Charge batteries overnight or ensure eight hours of charge
between use.
Replace batteries. Refer to Removing/Installing the Battery
Box on page 30.
Batteries weak, won’t hold charge.
Batteries not Charging.
Charger not working.
Replace charger. Contact Dealer or a qualified technician.
Battery connections loose.
Check all connections. Secure connections. Refer to
Removing/Installing the Battery Box on page 30.
No current at wall outlet.
Switch another wall outlet.
Bad connection on charger, charger cable, plug Replace charger or internal repairs required. Contact Dealer
or internal wiring problem.
or a qualified technician.
Batteries draw excessive current when Battery failure.
charging.
Replace batteries. Refer to Removing/Installing the Battery
Box on page 30.
Battery indicator shows the charge
level is low - too Soon after being
recharged.
Charger not working.
Have charger checked. Service or replace the charger.
Contact Dealer or a qualified technician.
Replace batteries. Refer to Removing/Installing the Battery
Box on page 30.
Weak batteries.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
14 TROUBLESHOOTING
SOLUTION
SYMPTOM
Scooter will not drive.
PROBABLE CAUSE
Error
Check service indicator light on control panel (FIGURE 6.1 on
page 25). If flashing, count the number of flashes and refer to
Brake release lever disengaged.
Engage brake release lever. Refer to Engaging/Disengaging the
Brake Release Lever on page 22.
Batteries require charging.
Key not fully plugged in.
Charger plugged in.
Charge batteries. Refer to Charging the Batteries on page 32.
Ensure key is inserted fully into keyswitch.
Unplug charger from scooter.
Circuit breaker tripped.
page 55. If breaker trips again, it may indicate need for internal
repairs. Contact Dealer or a qualified technician.
Fuse blown in battery box.
Soft stop engaged. If key is turned off while
driving, the scooter holds power for 1.5 seconds
slowly decelerating to a stop.
Contact Dealer or qualified technician.
With key in the off position, wait for 30 seconds and turn key
to the on position.
Battery connections loose.
Check all connections. Secure connections. Refer to
Removing/Installing the Battery Box on page 30.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
14 TROUBLESHOOTING
14.2 Service Indicator Error Codes
FLASH DESCRIPTION
MEANING
Battery Low
The batteries are running low.
• Recharge the batteries.
The batteries have run out of charge.
• Recharge the batteries.
Battery voltage is too high. This may occur if overcharged &/or traveling down a long slope.
• If traveling down a slope, reduce your speed to minimize the amount of regenerative charging.
• Check the battery and associated connections and wiring.
1
2
3
Low Battery Fault
High Battery Fault
Current Limit Time-out
Park Brake Fault
The motor has been exceeding its maximum current rating for too long. This may be due to a faulty motor.
• Check the motor and associated connections and wiring.
4
5
6
• Turn the controller off, leave for a few minutes and turn back on again.
Either a park brake release switch is active or the park brake is faulty.
• Check the park brake and associated connections and wiring.
• Ensure any associated switches are in their correct positions.
The Throttle is out of neutral when turning the controller on.
• Ensure the throttle is in neutral when turning the controller on.
• The Throttle may require re-calibration.
Throttle OONAPU
Speed Pot Fault
Motor Voltage Fault
Other error
The throttle, speed limit pot, SRW or their associated wiring may be faulty.
• Check the throttle and speed pot and associated connections and wiring.
The motor or its associated wiring is faulty.
• Check the motor and associated connections and wiring.
The controller may have an internal fault.
• Check all connections & wiring.
7
8
9
Push/Rollaway Fault
The scooter has exceeded the Push or Rollaway speed limits.
• Turn the controller off and then on again.
10
54
Download from Www.Somanuals.com. All Manuals Search And Download.
14 TROUBLESHOOTING
14.3 Resetting the Circuit Breaker
WARNING
ƽ
NEVER defeat or bypass the circuit breaker. ONLY replace with a circuit breaker of the same rating.
Key must be removed from ignition before resetting circuit breaker.
Lynx L-3 shown. Lynx L-4 circuit breaker button is in the same location.
Resetting the circuit breaker may be needed if the scooter does not turn on and the reset button has popped out about .25
inch.
1. To reset, press the circuit breaker button located below the seat.
Seat
Circuit Breaker Button
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Invacare Corporation
USA
Canada
One Invacare Way
Elyria, Ohio USA
44036-2125
570 Matheson Blvd E Unit 8
Mississauga Ontario
L4Z 4G4 Canada
800-668-5324
© 2011 Invacare Corporation. All rights
reserved. Republication, duplication or
modification in whole or in part is prohibited
without prior written permission from
Invacare. Trademarks are identified by ™ and
®. All trademarks are owned by or licensed to
Invacare Corporation or its subsidiaries unless
otherwise noted.
800-333-6900
For more information regarding Invacare products, parts, and
Part No. 1143205
Rev H - 04/11
Download from Www.Somanuals.com. All Manuals Search And Download.
|