Invacare Mobility Aid 1085144 User Manual

Reliant Bath Lift (RBL250)  
Pendant/Cable/Current Limit Device Replacement Kit  
Assembly,Installation and Operating Instructions  
Kit No. 1085144  
NOTE: Check all parts for shipping damage. In case of dam- 1. Securetheframetothefloorwiththesuctioncupsorby  
age, DONOTuse. ContactyourDealerforfurtherinstruction.  
standing on the frame base during removal of the seat.  
2. Press the UP button on the pendant to raise the  
seat all the way up (DETAIL "A").  
SAFETY SUMMARY  
The following recommendations are made for the  
safe replacement of the PENDANT/CABLE/CUR-  
RENT LIMIT DEVICE:  
3. Grasp the handgrip on the battery pack and pull  
upwards to remove it from the motor shroud as  
shown in DETAIL "B".  
GENERAL WARNINGS  
4. Press and hold the spring loaded chair release  
button to release the seat (DETAIL "C").  
DO NOT insta ll or use this e quipme nt without  
first re a ding a nd unde rsta nding this instruc -  
tion she e t. If you a re una ble to unde rsta nd  
the Wa rnings, Ca utions or Instruc tions in this  
Instruc tion She e t a nd in the Owne r's Ope ra t-  
ing a nd Ma inte na nc e Ma nua l (Pa rt No.  
1081003) provide d with the Ba th Lift, c onta c t  
a he a lthc a re profe ssiona l, de a le r or te c hni-  
c a l pe rsonne l be fore a tte mpting to insta ll this  
kit, othe rwise , injury or da ma ge ma y oc c ur.  
5. While holding the button with one hand, grasp the  
seat bottom firmly with your other hand.  
6. Slidetheseatupuntiltheslideblockdisengagesfrom  
the groove in the frame as shown in FIGURE 1.  
7. Grasp the handgrip on the battery pack and push  
downwards to install onto the motor shroud.  
8. Press the DOWN button on the pendant to lower  
the bath lift to the lowest position (DETAIL "A").  
This kit MUST b e insta lle d b y a n Inva c a re  
De a le r o r te c hnic a l p e rso nne l.  
9. If necessary, remove the bath lift frame from the  
bathtub. Refer to REMOVING THE FRAME FROM  
THE BATHTUB in this instruction sheet.  
INSTALLATION WARNINGS  
Afte r ANY a djustme nts, re pa ir or se rvic e a nd  
BEFORE use , m a ke sure a ll a tta c hing ha rd -  
wa re is tighte ne d se c ure ly - othe rwise injury  
or da ma ge ma y oc c ur.  
DETAIL "B"  
STEPS 2 AND 7  
DETAIL "A"  
STEPS 1 AND 8  
PULL UP TO REMOVE  
Use p rop e r lifting te c hniq ue s to a void in-  
jury. Ke e p b a c k stra ig ht a nd b e nd kne e s  
whe n lifting c om p one nts of the b a th lift.  
Down Button  
Pendant  
PUSH DOWN TO  
é
INSTALL  
REPLACING THE PENDANT/ CABLE/  
CURRENT LIMIT DEVICE  
NOTE: Refer to the INSTALLATION WARNINGS in the  
SAFETY SUMMARY of this instruction sheet.  
ê
Handgrip  
Motor  
Shroud  
Up  
Removing the Seat (FIGURE 1)  
Button  
Battery Pack  
WARNING  
Seat  
Recess  
To p re ve nt p inc hing injury b e twe e n se a t  
b a c k a nd m otor shroud whe n re m oving /  
insta lling the se a t, DO NOT gra sp se a t a ny-  
whe re othe r tha n a t the re c e ss a t the top  
(DETAIL "C"), the op e ning a t the b ottom of  
the se a t or the lip a t the top of the se a t.  
DETAIL "C"  
STEP 4  
Spring Loaded Chair Release Button  
LIFT THE SEAT  
To pre ve nt fra me from tipping whe n re mov-  
ing se a t, e ithe r suc tion the fra me to the floor  
or pla c e one foot on the fra m e ba se whe n  
re m oving / insta lling the se a t.  
é
C AUTIO N  
STEPS 5-6  
The ba th lift se a t MUST be re move d from the  
to p o f the lifting c yc le , othe rwise , da ma ge  
to the unit ma y oc c ur.  
Slide  
Block  
Seat Bottom  
DO NOT gra sp se a t by side fla ps, othe rwise  
da ma ge to the ba th lift or the ba thtub ma y  
o c c ur.  
Frame  
Groove  
FIGURE 1 - REMOVING THE SEAT  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Spade Connector Wires  
RED  
STEPS 1 - 2  
Connection to  
Motor Shroud  
YELLOW (+) Wire  
BLACK Spade  
Spade  
Connector  
Connector  
Battery  
Connector  
Mounting  
Screws  
(Nuts NOT  
SHOWN)  
Pendant  
Cable  
Nut  
Mounting  
Bracket  
BLUE (-)  
Wire  
Flared End  
Mounting Screws  
YELLOW (+) Wire  
DETAIL "A"  
STEP 3  
LOOSEN  
FIGURE 4 - REMOVING THE MOTOR SHROUD  
- RELEASING THE CABLES  
FlatScrew  
(DO NOT  
REMOVE)  
BLUE (-)  
Wire  
Removing the Battery Connector (FIGURE 5)  
Bare  
Wire  
1. Remove the two (2) mounting screws and nuts  
securing the battery connector to the motor shroud  
as shown in FIGURE 5.  
Insulated  
Wire  
Motor  
Shroud  
Battery  
Connector  
FIGURE 5 - REMOVING THE BATTERY  
C O NNEC TO R  
2. Carefully pull the battery connector away from the  
motor shroud.  
3. Loosen, but do not remove the two (2) flat screws  
on the battery connector to release the YELLOW  
(+) and BLUE (-) wires.  
Rem oving Current Lim it Device (FIGURE 6)  
1. Remove the two (2) mounting screws and nuts se-  
curing the current limit device to the motor shroud.  
4. Pull the YELLOW (+) and BLUE (-) wires through  
the motor shroud.  
NOTE: EXISTING mounting screws and nuts will be  
used to secure NEW current limit device to motor  
shroud.  
5. Remove the current limit device. Refer to REMOV-  
ING CURRENT LIMIT DEVICE in this instruction  
sheet.  
2. Remove the pendant/cable/current limit device as-  
sembly.  
3. Install NEW pendant/cable/current limit device as-  
sembly. Refer to INSTALLING NEW CURRENT  
LIMIT DEVICE in this instruction sheet.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Battery Connector (FIGURE 7)  
Mounting  
Screws  
REAR  
C AUTIO N  
The BLUE (-) a nd YELLO W (+) wire s MUST  
b e insta lle d p ro p e rly, o the rwise , se rio us  
d a m a g e to the e le c tric a l syste m o f the  
b a th lift m a y o c c ur.  
BLUE and  
YELLOW  
Battery  
Connector  
Wires  
Motor  
Shroud  
1. Position the BLUE (-) wire through the FRONT hole  
and the YELLOW (+) wire through the REAR hole  
as shown in DETAIL "D" of FIGURE 7.  
Spade  
Connector  
Wires  
FRO NT  
2. If necessary, loosen, but do not remove the two  
(2) flat screws in the battery connector (DETAIL  
"E").  
3. Visually inspect the battery connector to find the  
POSITIVE (+) and NEGATIVE (-) channels. Refer  
to DETAIL "E" of FIGURE 7.  
Current Limit Device  
Pendant Cable  
4. Insert the bare end of the YELLOW (+) wire into  
the POSITIVE (+) channel.  
Nuts  
FIGURE 6 - REMOVING CURRENT LIMIT  
DEVIC E  
C AUTIO N  
Installing NEW Current Lim it Device  
(FIGURE 6)  
DO NO T tig hte n the fla t sc re w o nto the  
insula te d p o rtio n o f the wire . Ensure the  
sc re w se c u re s th e b a re wire O NLY.  
1. Position the NEW current limit device on the in-  
side of the motor shroud with the blue and yellow  
battery connector wires towards the REAR of the  
shroud and the pendant cable towards the FRONT  
of the shroud as shown in FIGURE 6.  
5. Tighten the flat screw to secure the wire to the battery  
connector. Refer to DETAIL "F" of FIGURE 7.  
6. Repeat STEPS 4 - 5 to install the BLUE (-) wire  
into the NEGATIVE (-) channel.  
2. Align the mounting holes of the current limit device  
and the motor shroud and secure with the two (2)  
existing mounting screws and nuts. Tighten se-  
curely.  
7. Ensure BOTH wires are securely installed in the  
battery connector.  
NOTE: If installed properly, the wires should not pull  
out of the battery connector when gently tugged.  
3. Install the battery connector. Refer to INSTALLING  
THE BATTERY CONNECTOR in this instruction  
sheet.  
8. Position the battery connector on the motor shroud  
with the flared end on the bottom as shown in FIG-  
URE 7.  
9. Align the mounting holes of the battery connector  
with the mounting holes of the motor shroud.  
10. Secure the battery connector to motor shroud with the  
two (2) mounting screws and nuts. Tighten securely.  
11. Install the motor shroud. Refer to INSTALLING THE  
MOTOR SHROUD in this instruction sheet.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
DETAIL "D" - STEP 1  
1. Connect the spade connector wires to the motor  
in the following manner:  
REAR of  
Motor  
Shroud  
FRONT of  
Motor  
Shroud  
A. BLACK spade connector wire to lower spade.  
B. RED spade connector wire to upper spade.  
C AUTIO N  
FRONT  
Hole  
DO NO T se c ure the p e nd a nt c a b le b e -  
yo nd the m id d le o f the c a b le (m e a sur-  
ing fro m the c urre nt lim it d e vic e to the  
p e n d a n t), o th e rwise d a m a g e to th e  
Yellow (+) Wire  
c a b le m a y re sult.  
.
2. Secure the pendant cable and the spade connec-  
tor wire wrap to the motor with the mounting bracket  
as shown in FIGURE 8.  
REAR Hole  
Blue (-) Wire  
DETAIL "E" STEPS 2-3  
DETAIL "F" - STEP 5  
3. Alignthemountingholesofthemountingbracketand  
motor and secure the mounting bracket with the two  
(2) EXISTING mounting screws. Tighten securely.  
Flat Screws  
POSITIVE (+)  
Battery  
Connector  
Channel  
4. Positionthemotorshroudoverthemotor, aligning the  
mounting holes of the motor shroud and motor.  
YELLOW  
(+) Wire  
Bare  
End of  
Wire  
5. Install the machine screw and washer in the side  
mounting hole. Tighten securely.  
6. Install the two (2) self-locking screws and two (2)  
washersinthefrontmountingholes. Tightensecurely.  
Insulated  
Wire  
BLUE (-)  
Wire  
7. Grasp the handgrip on the battery pack and push  
downwards to install it onto the motor shroud.  
NEGATIVE  
(-) Channel  
TIGHTEN  
Flathead Screw (DO  
Flared End of Battery Connector  
WARNING  
NOT REMOVE)  
To pre ve nt fra m e from tipping whe n ra ising  
the b a th lift witho ut the se a t insta lle d , e i-  
the r suc tion the fra m e to the floor or p la c e  
one foot on the fra m e b a se .  
STEPS 8-10  
YELLOW (+) Wire  
8. Secure the frame to the floor with the suction cups or by  
standing on the frame base.  
Battery  
Connector  
Mounting  
Screws  
(Nuts NOT  
SHOWN)  
9. Test the operation of the bath lift by pressing the  
UP and DOWN buttons on the pendant to ensure  
proper installation of the NEW pendant.  
10. Perform one (1) of the following:  
PROPER OPERATION - Install the bath lift  
frame into the bathtub. Refer to INSTALLING  
BATH LIFT INTO THE BATHTUB in this in-  
struction sheet.  
BLUE (-)  
Wire  
Flared End  
FIGURE 7 - INSTALLING THE BATTERY  
IMPROPER OPERATION - If the bath lift does  
not respond correctly when the pendant but-  
tons are pushed (for example, the lift raises  
when the DOWN button is pushed) or if it does  
not work at all, repeat STEPS 1-9 making sure  
the spade connectors are properly connected.  
C O NNEC TO R  
Installing the Motor Shroud (FIGURE 8)  
C AUTIO N  
Th e sp a d e c o n n e c to rs MUST b e c o n -  
n e c te d to th e m o to r a s sh o wn in FIG -  
URE 8 - o the rwise , the p e nd a nt will o p -  
e ra te im p ro p e rly.  
NOTE: If improper operation exists, contact  
Invacare at the number on the back of this in-  
struction sheet before using.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
DO NOT Secure Here  
STEP 2  
Spade Connector Wire Wrap  
Mounting Screw  
Current  
Limit  
STEPS 2-3  
Device  
Mounting  
Bracket  
Secure Here  
Pendant  
Pendant  
Cable  
STEPS 1 - 3  
BLACK Spade  
Connector Wire  
(STEP 1)  
To Current Limit  
Device  
RED Spade  
Connector  
Wire  
Motor Shroud  
Washer  
STEPS 4-6  
Upper  
Spade  
(STEP 1)  
Machine  
Screw  
Self-locking  
Screws  
Secure Pendant  
Cable and Spade  
Connector Wire  
Wrap Together  
(STEP 2)  
Nut  
Washer  
Mounting  
Bracket  
Mounting  
Screws  
Mounting  
Holes  
Lower Spade  
Pendant  
Motor  
FIGURE 8 - INSTALLING THE MOTO
A. Position the rubber pads of the frame just in front of  
the curve at the bottom of the back of the bathtub.  
Installing the Bath Lift into the Bathtub  
(FIGURE 9)  
B. Install the seat. Refer to INSTALLING THE  
SEAT in this instruction sheet.  
WARNING  
ALWAYS lo we r the b a th lift fra m e to the  
lo we st p o sitio n BEFORE p e rfo rm ing this  
p ro c e d ure . Othe rwise , the b a th lift fra m e  
m a y tip d uring insta lla tio n a nd injury o r  
d a m a g e m a y o c c ur.  
C. Position the frame to align the line on the entry/  
exit side flap with the inside edge of the bathtub  
as shown in DETAIL "G" of FIGURE 9.  
WARNING  
The fra m e m ust b e p o sitio ne d so tha t  
the sid e fla p o f the se a t o n the e ntry/  
e xit sid e o f the b a thtub is fully sup -  
p o rte d b y the sid e o f the b a thtub . The  
insid e e d g e o f the b a thtub MUST b e  
a lig ne d with the line o n this sid e fla p .  
Th e fra m e MUST b e p la c e d in to a n  
EMPTY b a th tu b .  
1. Clean tub and wipe suction cups with a damp cloth.  
2. Press the DOWN button on the pendant to lower  
the bath lift to the lowest position.  
D. Ensure the rubber pads and suction cups are  
positioned flat on the bottom of the bathtub.  
3. Grasp the handgrip on the battery pack and pull  
upwards to remove it from the motor shroud as  
shown in FIGURE 9.  
NOTE: Pull up on suction cup loops to release suc-  
tion cups from bathtub bottom.  
4. Place the frame into the bathtub.  
5. Perform the following steps to position the frame  
in the bathtub:  
6. Press firmly down onto the two (2) front suction cups  
toattachtheframesecurelytothebottomofthebath.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 1  
é STEP 2  
SIDE VIEW - STEPS 5A & 6  
Front of the  
Down  
Pendant  
PULL UP  
TO  
REMOVE  
Up  
Bathtub  
(fixture end)  
PRESS DOWN ON  
SUCTION CUP  
Motor  
Shroud  
Back of  
Suction  
Cup  
Loop  
the  
Bathtub  
Battery Pack  
DETAIL "G"  
STEP 5C  
Position of Line  
on Side Flap  
Side Flap  
Frame  
Suction  
Cup  
Entry/Exit  
Side Flap  
Rubber Pad  
FRONT VIEW - STEPS 5C-5D  
Seat  
Hinge  
Side Flaps  
Seat  
Bathtub  
Frame  
Inside Edge  
of Bathtub  
Suction Cups  
and Pads Flat  
on Bottom of  
bathtub  
PROPER POSITIONING OF  
ENTRY/ EXIT SIDE FLAP  
FIGURE 9 - INSTALLING THE BATH LIFT INTO THE BATHTUB  
Installing the Seat (FIGURE 10)  
3. Press the UP button on the pendant to raise the  
bath lift to the uppermost position.  
WARNING  
4. Grasp the handgrip on the battery pack and pull  
upwards to remove it from the motor shroud.  
To p re ve nt p inc hing injury b e twe e n se a t  
b a c k a nd m o to r shro ud whe n re m o ving /  
insta lling the se a t, DO NOT gra sp se a t a ny-  
whe re othe r tha n a t the re c e ss a t the top ,  
the o p e ning a t the b o tto m o f the se a t o r  
the lip a t the to p o f the se a t.  
5. Lowertheseatontotheframe, ensuringthattheslide  
block on the back of the chair slides down the two (2)  
grooves on the frame as shown in FIGURE 10.  
To p re ve nt fra m e fro m tip p ing whe n re -  
m o ving se a t, e ithe r suc tio n the fra m e to  
the flo o r o r p la c e o ne fo o t o n the fra m e  
b a se whe n re m o ving / insta lling the se a t.  
NOTE: The seat MUST be lowered onto the frame  
until the spring loaded chair release button locks in  
place and an audible "click" is heard.  
Recess  
LOWER  
Seat  
C AUTIO N  
SEAT  
The b a th lift se a t MUST b e insta lle d fro m  
the up p e rm o st lifting p o sitio n, o the rwise ,  
d a m a g e to the unit m a y o c c ur.  
DO NOT g ra sp se a t b y sid e fla p s to a void  
d a m a g e to the b a th lift o r the b a thtub .  
Slide  
Block  
Spring Loaded Chair  
Release Button  
1. Secure the frame to the floor with the suction cups or by  
standing on the frame base.  
2. Grasp the handgrip on the battery pack and push  
downwards to install it onto the motor shroud.  
Seat  
Groove  
Frame  
FIGURE 10 - INSTALLING THE SEAT  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW  
APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.  
This wa rra nty is e xte nd e d o nly to the o rig ina l p urc ha se r/ use r o f o ur p ro d uc ts.  
This wa rra nty g ive s yo u sp e c ific le g a l rig hts a nd yo u m a y a lso ha ve o the r le g a l rig hts  
whic h va ry fro m sta te to sta te .  
Inva c a re wa rra nts its p ro d uc t to b e fre e fro m d e fe c ts in m a te ria ls a nd wo rkm a nship fo r  
o ne (1) ye a r fo r the o rig ina l p urc ha se r. If within suc h wa rra nty p e rio d a ny suc h p ro d uc t  
sha ll b e p rove n to b e d e fe c tive , suc h p rod uc t sha ll b e re p a ire d or re p la c e d , a t Inva c a re 's  
o p tio n. This wa rra nty d o e s no t inc lud e a ny la b o r o r ship p ing c ha rg e s inc urre d in re -  
p la c e m e nt p a rt insta lla tio n o r re p a ir o f a ny suc h p ro d uc t. Inva c a re 's so le o b lig a tio n  
a nd yo ur e xc lusive re m e d y und e r this wa rra nty sha ll b e lim ite d to suc h re p a ir a nd / o r  
re p la c e m e nt.  
Fo r wa rra nty se rvic e , p le a se c o nta c t the d e a le r fro m who m yo u p urc ha se d yo ur In-  
va c a re p ro d uc t. In the e ve nt yo u d o no t re c e ive sa tisfa c to ry wa rra nty se rvic e , p le a se  
write d ire c tly to Inva c a re a t the a d d re ss o n the b o tto m o f the p a g e . Pro vid e d e a le r's  
na m e , a d d re ss, m o d e l num b e r, d a te o f p urc ha se , ind ic a te na ture o f the d e fe c t a nd , if  
the p ro d uc t is se ria lize d , ind ic a te the se ria l num b e r.  
Inva c a re Co rp o ra tio n will issue a re turn a utho riza tio n. The d e fe c tive unit o r p a rts m ust  
b e re turne d fo r wa rra nty insp e c tio n using the se ria l num b e r, whe n a p p lic a b le , a s id e n-  
tific a tio n within thirty (30) d a ys o f re turn a utho riza tio n d a te . DO NOT re turn p ro d uc ts to  
o ur fa c to ry witho ut o ur p rio r c o nse nt. C.O.D. ship m e nts will b e re fuse d ; p le a se p re p a y  
ship p ing c ha rg e s.  
LIMITATIONS AND EXCLUSIONS: THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING  
FROM NORMAL WEAR OR FAILURE TO ADHERE TO THE ENCLOSED INSTRUCTIONS. IN ADDI-  
TION, THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF  
THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED; PRODUCTS SUBJECTED TO NEGLI-  
GENCE, ACCIDENT, IMPROPER OPERATION, MAINTENANCE OR STORAGE; OR PRODUCTS  
MODIFIED WITHOUT INVACARE'S EXPRESS WRITTEN CONSENT INCLUDING, BUT NOT LIM-  
ITED TO: MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS:  
PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE  
SPECIFIC CONSENT OF INVACARE; PRODUCTS DAMAGED BY CIRCUMSTANCES BEYOND  
INVACARE'S CONTROL; PRODUCTS REPAIRED BY ANYONE OTHER THAN AN AUTHORIZED  
INVACARE DEALER, SUCH EVALUATION SHALL BE SOLELY DETERMINED BY INVACARE.  
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRAN-  
TIES, IF ANY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR  
A
PARTICULAR PURPOSE.  
IT SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESSED WARRANTY PROVIDED  
HEREIN AND THE REMEDY FOR VIOLATIONS OF ANY IMPLIED WARRANTY SHALL BE LIMITED  
TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CON-  
TAINED HEREIN. INVACARE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDEN-  
TAL DAMAGES WHATSOEVER.  
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/ PROVINCIAL LAWS AND RE-  
Q UIREMENTS.  
Invacare Corporation  
USA  
One InvacareWay  
Elyria, Ohio USA  
44036-2125  
Invacare is a registered trademark of Invacare Corporation.  
©
1999 Invacare Corporation  
800-333-6900  
Form No. 98-321 Part No. 1085312 RevA (1)-1/00  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Intellinet Network Solutions Network Router 150N ADSL2+ User Manual
Intel TV Cables 307017 001 User Manual
Inter Tel Telephone 8278659 User Manual
Jensen Portable Radio 256939 User Manual
Karcher Pressure Washer K 201 User Manual
Kenmore Gas Grill 1191643301 User Manual
Kenmore Water System 350 Series User Manual
KitchenAid Clothes Dryer KEYE650V User Manual
KitchenAid Dishwasher 119 User Manual
Konica Minolta All in One Printer 2480 MF User Manual