ITIpci 5232E Four Port Ethernet and
Fast Ethernet PCI Host Adapter
Installation and User’s Guide
Order Number 9806-5232M
IntraServer Technology, Inc., Copyright 1998
quad_enet.doc
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Class B Device Certification Statements
Federal Communications Commission Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against a harmful
interference in residential installations. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio or television equipment reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Move the equipment away from the receiver
Plug the equipment into an outlet on a circuit different from that to which the receiver is
powered
If necessary, the user should consult the dealer or an experienced radio/television technician
for additional suggestions
CAUTION: Only equipment certified to comply with Class B (computer input/output devices, terminals,
printers, etc.) should be attached to this equipment, and must have shielded interface cables.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and (2) this device must accept any interference
received , including interference that may cause undesired operation.
Each host adapter is equipped with an FCC compliance label which shows the FCC Identification number.
The full text of the label is in the preceding paragraph.
Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee
manufacturer could void the user’s authority to operate such equipment.
Canadian Compliance Statement
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le material brouiller
du Canada
European Compliance Statement
WARNING: This is a Class B product. In domestic environments this product may cause radio
interference in which case the user may be required to take adequate measures.
Please write to IntraServer Technology, Inc, Seven October Hill Road, Holliston, MA 01746 with regards
to any questions on this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction........................................................................................................................ 6
ITI-5232E Four Port Ethernet and FAST Ethernet Kit Contents........................................7
Connectors and Indicator LEDs...............................................................................................8
Hardware Installation........................................................................................................ 9
System Requirements ................................................................................................................9
Installing the adapter.................................................................................................................9
Network Device Driver Installation Instructions............................................................ 11
Windows NT.............................................................................................................................11
Contents of the driver kit.......................................................................................................................11
Installing the ITI-5232E (DC21X4 Driver) on Windows NT: ..........................................................12
Windows 95 Installation for PCI systems..............................................................................18
NetWare ....................................................................................................................................23
Linux..........................................................................................................................................25
For information regarding drivers, installation, and support for Linux please visit our World
Wide Web site at http://intraserver.com/support/faq.html.........................................................25
Digital UNIX.............................................................................................................................26
Digital OpenVMS.....................................................................................................................27
Appendix A ....................................................................................................................... 28
Digital’s SRM Console Settings ..............................................................................................28
Displaying and Setting Ethernet Port Characteristics............................................................................28
Appendix B ....................................................................................................................... 30
Connector Pin Assignments ....................................................................................................30
Cabling Requirements .............................................................................................................31
Appendix C: Troubleshooting....................................................................................... 32
Windows NT Version 4.0 and 3.51 .........................................................................................32
Error messages ......................................................................................................................................32
Driver initialization errors:................................................................................................................33
Driver run time errors:.......................................................................................................................33
Windows 95...............................................................................................................................34
Appendix D: Adapter Specifications............................................................................. 36
ITI-5232E Four Port 10/100 Ethernet PCI adapter .............................................................36
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
Table 1 ITI-5232E Adapter Models ________________________________________________________7
Table 2 Connections and Indicator LEDs ___________________________________________________8
Table 3 Contents of Software Distribution Floppy ___________________________________________11
Table 4 Digital UNIX and OpenVMS SRM Console Media Selection _____________________________28
Table 5 8-Pin MJ Connector Pin Assignments_______________________________________________30
Table 6 Adapter to Network Hub Wiring ___________________________________________________31
Table 7 Adapter to Adapter (point to point) Wiring___________________________________________31
Table 8 DC21X4 NT driver error codes____________________________________________________33
Figures
Figure 1 Connectors and Indicator LEDs ___________________________________________________8
Figure 2 8-Pin MJ Connector (Front)_____________________________________________________30
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
IntraServer’s Four Port ITI-5232E provides four FAST (10/100Mb/sec) channels from a single PCI
host slot, providing the maximum network integration for high performance network server needs.
Each of four ports is capable of running FAST, FAST Full Duplex, or 10Mb/sec for configuration
flexibility, allowing a single card to communicate with FAST or Standard Ethernet systems
simultaneously.
With each port capable of up to 200Mb/sec in FAST Full Duplex mode, a single ITI-5232E is
capable of up to 800Mb/sec.
ITI-5232E features include:
-
-
-
-
High performance PCI bus master, 32-bit direct memory access (DMA)
architecture
Four independent 10/100 Digital 21143-PC Ethernet channels for optimal
network performance
Support for all Alpha and Intel Operating systems, including Windows 95,
Netware, Windows NT, OpenVMS, Digital UNIX and Linux.
Direct 10Base-T and 100Base-TX network connection with full auto-negotiation
support
-
-
-
-
Half and Full Duplex mode of operation
Jumperless “Plug and Play” implementation
Speed, Link Status, Transmit and Receive activity LEDs
3.3 and 5.0 volt universal PCI support
All major operating systems are supported on the adapter, including:
- Windows NT, Windows 95, Windows 3.x
- OS/2
- NetWare 3.x, 4.x
- Digital UNIX
6
Download from Www.Somanuals.com. All Manuals Search And Download.
- OpenVMS
-
-
MS/DOS
Linux
Two ITI-5232E models are available, as described in Table 1.
Model
Interrupts
Required
1
Description
Interrupt Assignment
ITI-5232E-N
Channel 0 – Interrupt A
Channel 1 – Interrupt A
Channel 2 – Interrupt A
Channel 3 – Interrupt A
Channel 0 – Interrupt A
Channel 1 – Interrupt B
Channel 2 – Interrupt C
Channel 3 – Interrupt D
Four Port Channel FAST Ethernet Adapter for
Windows NT, Windows 95 operating systems
that support sharing of PCI interrupts
ITI-5232E-O/U
4
Four Port Channel FAST Ethernet Adapter for
Digital UNIX, OpenVMS operating systems that
do not support sharing of PCI interrupts
Table 1 ITI-5232E Adapter Models
ITI-5232E Four Port Ethernet and FAST Ethernet Kit Contents
Your ITI-5232E kit includes the items shown below. Verify that you have the following
items before you proceed with the installation:
•
•
•
ITI-5232E Four Port Ethernet and FAST Ethernet Adapter
Software installation kit
This installation guide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connectors and Indicator LEDs
The ITI-5232E provides four 8-pin Modular Jack (MJ) connectors for connection with
your network. Each of these four ports supports either Twisted Pair Category 3 or 5 cable
for 10Mb/s connections, or Category 5 cable for 100Mb/sec operation.
Figure 1 shows the ITI-5232E Adapter connectors and indicator LEDs.
1
Port 0
2
Port 1
3
Port 2
4
Port 3
5
7
Port 0
Port 1
Port 2
Port 3
6
8
Figure 1 Connectors and Indicator LEDs
Table 2 describes the ITI-5232E Four Port Fast Ethernet Adapter connectors and indicator LEDs.
Reference
Component
Channel 0 8-pin MJ Connector
Description
10/100 Mb/s twisted-pair network
connector for Channel 0
10/100 Mb/s twisted-pair network
connector for Channel 1
10/100 Mb/s twisted-pair network
connector for Channel 2
10/100 Mb/s twisted-pair network
connector for Channel 3
100 Mb/s (Left LED)
❶
❷
❸
❹
❺
Channel 1 8-pin MJ Connector
Channel 2 8-pin MJ Connector
Channel 3 8-pin MJ Connector
Channel 0 Indicator LEDs
Activity (Center LED)
Link (Right LED)
100 Mb/s (Left LED)
Activity (Center LED)
Link (Right LED)
100 Mb/s (Left LED)
Activity (Center LED)
Link (Right LED)
100 Mb/s (Left LED)
❻
❼
❽
Channel 1 Indicator LEDs
Channel 2 Indicator LEDs
Channel 3 Indicator LEDs
Activity (Center LED)
Link (Right LED)
Table 2 Connections and Indicator LEDs
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
This chapter describes how to install the ITI-5232E adapter in your PCI based bus master compatible
computer, and how to connect it to your network.
The ITI-5232E host adapter is Plug and Play on the host systems PCI bus, and no configuration of
the adapter hardware is necessary.
System Requirements
Before you begin the installation procedure, you will need:
•
•
•
•
An available PCI bus master expansion slot
A system that is compatible with the PCI Specification, Version 2.1
A floppy disk drive for loading the software drivers
UTP category 3,4 or 5 cable (type dependant on your network type)
For multi-channel adapters such as the ITI-5232E it is required that your host system
firmware or BIOS support PCI bridging. If your host does not support PCI bridging contact
your system vendor for a BIOS upgrade. If your system can not be brought into compliance
with the PCI bridge specification, then you will not be able to use multi-channel ITIpci host
adapters.
Installing the adapter
The following procedure should be used to install the ITI-5332E adapter:
1. Turn OFF the power to the computer system, and to all peripherals directly connected to
the system (monitor, printer, external SCSI enclosures, etc.)
2. Unplug the system from the AC power line
3. Use an anti-static strap or precautions to avoid static discharge to your computer system
or the ITI-5232E adapter
4. Remove the access cover from your system (refer to the system’s documentation)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Locate a free PCI expansion slot (small white connector on the system’s motherboard)
and remove the screw and metal bracket for the selected slot. Be certain not to install the
adapter in an ISA or EISA slot, which are longer than the PCI slots
6. Install the adapter in the selected slot. The module should fit without forcing, and should
line up with the I/O bulkhead. Be certain that the adapter is fully seated in the slot
7. Replace the retaining screw removed in step 5
8. Connect to your Ethernet HUB using uncrossed Twisted Pair cable.
After installation, re-assemble the system enclosure, and proceed with Software installation.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Device Driver Installation Instructions
Windows NT
The ITI-5232E Four Port Ethernet and Fast Ethernet adapter uses the industry leading
Fast Network Engine, Digital’s DC21143 PCI MAC. Digital’s DC21X4.SYS mini-port
driver is used to support the four Ethernet channels on the card.
Contents of the driver kit
Your ITI-5232E kit includes a floppy disk, which contains the Windows NT and
Windows 95 drivers.
The floppy disk contains the following files and directories:
Operating
System
A:\WINNT
Architecture
(NT only)
\ALPHA
File Name
File Description
\ DC21X4.SYS
The Alpha executable driver
file for DC21143 Ethernet
Chip
\INTEL
\ DC21X4.SYS
\ DC21X4.SYS
The Intel executable driver file
for DC21143 Ethernet Chip
A:\WIN95
A:\
The Intel executable driver file
for DC21143 Ethernet Chip
\NDIS.VXD
\DISK1
NDIS Wrapper file
Flag file for NT
\NETPCI.INF
\OEMSETNT.INF
\README.TXT
Win’95 Setup information file
NT Setup information file
Information released since the
last publication of the
documentation (if any)
Information specific to this
software release (if any)
\RELEASE.NOT
Table 3 Contents of Software Distribution Floppy
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the ITI-5232E (DC21X4 Driver) on Windows NT:
Follow the procedure below to install the NT driver on your Intel or Alpha based system.
The choices you are given may vary slightly from these examples based on your
machine’s current network configuration and options. See your system administrator for
any additional information.
Note: Digital’s Alpha systems use a dynamic link library file (DLL) called a
hardware abstraction layer (HAL). This file can be found on your boot disk at the
location \os\hal.dll. This is a system file and is hidden. You must use the “show
system and hidden files” option under explorer to see this file.
Certain Alpha systems will hang after installing multi-port Ethernet cards unless
this file is updated to hal.dll dated on or after 26-MAY-1998.
If you experience this hang, shut down the machine, and remove the ITI-5232E
from your system. Contact Digital for an updated HAL, and installation
instructions.
1. From the Windows NT START Menu, select the Control Panel icon.
2. From the Control Panel menu select the Network icon.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
If a dialog box asks you "Do you want to install NT Networking?" select YES and
continue. Place the Windows NT installation media the CD-ROM reader, and
complete the Windows NT network installation. Consult Windows NT
documentation if you are unfamiliar with this process. Follow the on-screen
prompts until you are prompted for a Network Adapter Type.
3. From the “Network” dialog, select the Adapters tab, then select Add.
4. From the “Select Network Adapter” dialogue, select Have Disk…
13
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Insert the ITI-5232E driver diskette in your floppy drive and select OK.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
6. From the “Select OEM Option” dialogue, Select “IntraServer ITI5232E Four Port
10/100 Mbps Ethernet” adapter, and select OK.
7. A “Connection Type” dialog box will allow you to select the connection type
appropriate for your network configuration. The default connection type is
AutoSense, which should be correct for most network connections.
8. Should you need to change the media connection type, be certain to select the correct
connection type for your network. If not, the adapter port will not be able to “link” to
the network.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Upon completion, the selected adapter port(s) is (are) added to the Installed Adapter
Cards list in the Network Setting box (the number prefixing the adapter is the adapter
port number).
10. Select OK to complete the Network Setting initialization. Based on the protocols you
are running, one, or more dialog boxes may appear. See your network administrator
for appropriate settings for your network for each of the dialog boxes. A typical
dialog (TCP/IP) shown for example.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Shutdown and reboot the system.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 95 Installation for PCI systems
The following step should be taken in order to use the IntraServer Technology, Inc. ITI-
5232E Four Port Fast Ethernet 10/100 adapter in a system running Windows 95:
1. Power the machine down, unplug the AC power line, and remove the access cover.
2. Install the ITI5232 into an unused PCI slot. Attach the network cable(s) from the card
to your existing network device.
3. Replace the access cover of your machine.
4. Replace the AC power line, and boot Windows 95.
5. When Windows 95 detects the new hardware, a message:
"New Hardware Found, PCI Ethernet Controller" will be displayed.
6. Put the Software Installation Floppy in your Floppy drive, then select
Next >.
6. Windows ’95 will read the installation floppy, and will automatically find the ITI-
5232E Four Port Ethernet controller Select Finish. If you are the “Select Device” dialog
box to select the ITI-5232 Four Port 10/100 Mbps Ethernet Adapter” from the list and
select OK.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Windows ’95 may prompt you to insert the distribution media disk(s) to be installed
at this time.
13. Some files will be copied from your distribution media disk(s) and some from the
OEM distribution floppy disk.
14. If Windows prompts you for a file location of the distribution files, select the default
location A:\ and select OK.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
15. When all necessary files have been copied to your system, select Finish from the
“Add New Hardware Wizard” dialogue.
16. The preceding steps will be repeated for EACH of the four ports detected by
Windows ’95. You will need to repeat the above procedures until each of the four
ports have been added to your configuration.
17. Each port on the ITI-5232E Four Port Network adapter will be given an entry in the
adapter list in the “Network” dialogue.
18. The Enhanced mode driver should be used, and is selected by default.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
19. The ITI-5232E is capable of full AutoSense, which should allow plug and play
operation with your network. Should the need arise to specify the physical media,
select the “Advanced” tab, then select Connection Type, and select the connection
type that matches your network.
20. Select OK. Based on the network protocols running on your system, one or more
dialogue boxes may appear. See your network administrator for the network settings
for this machine.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
21. When prompted, allow the machine to restart, to allow the new network settings to
become active.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare
The Novell Netware driver, DC21x4 is used with both Netware 3.1x and Netware 4.x
servers.
Netware 3.x Server Driver
1. Prepare the hard drives of your server according to the instructions in your Netware
3.1x documentation.
2. While the server is down, insert the IntraServer Setup diskette into your server’s A
drive.
3. Copy the contents of a:\netware\311 or a:\netware\312 to the disk from which you
boot Netware 3.1x
4. Type SERVER at the DOS prompt press Enter to boot the Netware 3.1x Server.
5. Type LOAD INSTALL at the server console prompt and press Enter
6. Select System Options
7. Select Edit AUTOEXEC.NCF File
8. Edit the autoexec.ncf file. You must load the device driver once for each port used.
NetWare 4.x and 4.11
The Novell Netware driver DC21X4 is used with Netware 4.11 servers.
1. Type LOAD INSTALL at the server console prompt and press Enter.
2. On the Installation Options menu, select Driver options (load/unload disk and
network drivers).
3. On the Driver Options menu, select Configure Network Drivers. The system displays
the installed network drivers, and the Additional Driver Actions menu
4. Select a driver and press Enter. If the desired IntraServer driver is not on the list,
proceed to Step 5.
5. Insert the IntraServer Setup diskette into drive A and press<INS> to install the
unlisted driver.
6. Press Enter. The system scans path a:\ for uninstalled drivers.
7. Press Enter to install the NetWare 4.x driver in drive A.
8. Select yes to copy the driver DC21X4
23
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Enter information as prompted. You may modify the adapter’s default configuration
by changing its parameters when prompted. The default settings provide best results
in most cases.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Linux
For information regarding drivers, installation, and support for Linux please visit our
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital UNIX
Drivers for the ITI-5232E are on the Digital UNIX distribution kit beginning with
Version 4.0D. Digital UNIX will identify the ITI-5232E as four 21140 based Ethernet
controllers.
Once the hardware is installed in your system, boot the system using genvmunix, in the
following manner:
>>>boot –file genvmunix
This will cause Digital UNIX to scan all hardware devices in the system, and identify the
ITI-5232E . Four 21140 based Ethernet adapters will be identified.
Create a new kernel with support for the four Ethernet ports, identified in genvmunix by
using the doconfig command.
# doconfig
When doconfig completes backup your existing kernel as follows:
# cp /vmunix /vmunix.sav
Then copy the new kernel created by doconfig, to /vmunix, and shutdown and reboot with
your new kernel.
If you are unfamiliar with doconfig, refer to your Digital UNIX documentation for
additional information.
Note: Digital UNIX relies on the settings for media type and speed set by the SRM console.
See Appendix A for more information.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital OpenVMS
Drivers for the ITI-5232E are on the Digital OpenVMS distribution kit beginning with
Version 7.1. Digital OpenVMS will identify the ITI-5232E as four 21140 based adapters.
Follow the documentation for the network software you will be running on the adapter for
specific configuration information.
Note: Digital OpenVMS relies on the settings for media type and speed set by the SRM
console. See Appendix A for more information.
Note: If you are connecting “Point to Point” to another adapter, do not select Auto-Sense
for ewa0_mode. Also, many hubs do not support Auto-Sense, it is therefore recommended
that the correct media type and speed are selected manually.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Digital’s SRM Console Settings
When the ITI-5232E is being used in a Digital Alpha platform running OpenVMS or
Digital UNIX, the SRM console is used to set the port speed, media (cable) type and boot
protocols, and can also be used to test the module.
After powering your system up, and before booting your operating system, the system
will stop at the SRM console prompt. On a uni-processor machine, the SRM prompt is
“>>>” and on the primary processor of a multi-processor machine, is “P0>>>”.
Digital uses a set of “Environment Variables” to store the settings of certain user
definable parameters, which are passed to the operating system to allow the users
configuration information to stay consistent when the SRM passes control of the system
to the operating system.
Displaying and Setting Ethernet Port Characteristics
The Alpha console recognizes the Ethernet device as an EW port. There are two
commands that are necessary for setting and showing the Ethernet port:
SET and SHOW.
Use SHOW to display characteristics of the Ethernet port.
>>>Show EWn0_MODE
Where ‘n’ is the Ethernet port letter.
Use SET to set characteristics of the Ethernet port. The available settings for
Ethernet media type are shown in Table 4.
Parameter
Settings
Description
EWn0_MODE
TWISTED-PAIR
FAST
10Mb/sec Twisted Pair
100Mb/sec Twisted Pair
Half Duplex
FULL DUPLEX TWISTED PAIR
Full Duplex Twisted Pair
Not Supported
AUI
BNC
Not Supported
FAST FD
FAST Full Duplex
Table 4 Digital UNIX and OpenVMS SRM Console Media Selection
28
Download from Www.Somanuals.com. All Manuals Search And Download.
For example, to set the media type and speed to FAST Twisted Pair, enter the
command:
>>>set ewa0_mode FAST
If you will be remote booting via the Ethernet, you must also set the boot protocol
to match that of the boot node. Typically OpenVMS uses MOP protocol and UNIX
uses BOOTP.
For example to set a port to MOP (VMS) use:
>>>set ewa0_protocol MOP
Note: Port 0 will be the lowest controller letter found by the SRM console, “A” if there are
no other Ethernet ports in the system. If there is an onboard Ethernet controller, it will be
assigned port letter “A” and the ports on your ITI-5232 will be assigned “B,C,D and E” for
ports “0,1,2 and 3” respectively.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Connector Pin Assignments
Each of the Four 8-pin MJ connectors for 10/100 Mb/sec are wired as shown in Figure 2:
1 2 3 4 5 6 7 8
Figure 2 8-Pin MJ Connector (Front)
With the connection pins assigned as shown in Table 5:
Pin Number
Signal Name
1
2
3
4
5
6
7
8
Transmit +
Transmit -
Receive +
No Connection NC
No Connection NC
Receive -
TX (+)
TX (-)
RX (+)
RX (-)
No Connection NC
No Connection NC
Table 5 8-Pin MJ Connector Pin Assignments
Connection from the ITI-5232 adapter to a network hub must be made as shown in
Table 6:
Straight Through
Adapter Pin
Hub Pin
ÇÈ
ÇÈ
ÇÈ
TX (+)
TX (-)
RX (+)
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
RX (+)
RX (-)
TX (+)
ÇÈ
RX (-)
TX (-)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6 Adapter to Network Hub Wiring
Connection from the ITI-5232E adapter to another network adapter (point to point) must
be made as shown in Table 7:
Crossover
Adapter 1
Adapter 2
Pin
1
2
Pin
3
6
ÇÈ
ÇÈ
ÇÈ
TX (+)
TX (-)
RX (+)
RX (+)
RX (-)
TX (+)
3
1
4
4
5
5
ÇÈ
RX (-)
6
2
TX (-)
7
7
8
8
Table 7 Adapter to Adapter (point to point) Wiring
Cabling Requirements
In order for your network to operate properly, you must use a category of network cabling
that is appropriate for the data rate of the channel. For 10Mb/s operation, Category 3, 4
or 5 cable is appropriate. When operating in 100Mb/s or 100Mb/s Full Duplex, a
Category 5 cable should be used.
The maximum cable segment length supported at 100Mb/sec speed, on Category 5 cable
is 100M. Any single cable segment (adapter to adapter or adapter to network hub) must
be within the 100M length requirement.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C:
Troubleshooting
Windows NT Version 4.0 and 3.51
The most common problem encountered on Windows NT for Ethernet devices is a
mismatch of the port’s speed and media settings to those in use on the network. The most
simple check of correct cabling is to observe the status lights on the handle of the card.
Once the card is installed in the system, the software is installed, and the module is wired
to your network hub, the LINK light should be illuminated. If LINK fails to light, check
that your cable type and media settings are correct. Appendix B provides cable
information for all configurations.
If you are connected to a FAST hub, be sure card is set to AUTO1, FAST or FAST Full
Duplex, depending on the capability of your hub.
If you are connected to a 10Mb/sec hub, the card should be set to AUTO1, Twisted Pair or
Twisted Pair Full Duplex, depending on the capability of your hub.
Cables from the ITI-5232E to a hub MUST NOT BE CROSSOVER.
Cables from the ITI-5232E to another ITI-5232E MUST BE CROSSOVER.
1
TIP: If you are certain your cable type is correct, but you are not seeing LINK, setting the
port to match the hub port exactly (ex. FAST, not AUTO). Some hubs have trouble with
cards set to AUTO negotiate.
Error messages
The error messages are logged in the Windows NT Error Log and can be seen using the
Error Log Viewer (in NT's Administration Tools group).
Each error message has a standard NDIS error code and a driver's additional code. The
additional codes are listed in Table 8.
Error Message
Code
0x01
0x02
0x03
0x04
0x05
0x06
DC21X4_ERRMSG_REGISTRY
DC21X4_ERRMSG_ALLOC_MEMORY
DC21X4_ERRMSG_SROM
DC21X4_ERRMSG_MEDIA
DC21X4_ERRMSG_LOAD_CAM
DC21X4_ERRMSG_SYSTEM_ERROR
32
Download from Www.Somanuals.com. All Manuals Search And Download.
DC21X4_ERRMSG_TXM_JABBER_TIMEOUT 0x07
Table 8 DC21X4 NT driver error codes
Driver initialization errors:
NDIS_ERROR_CODE_UNSUPPORTED_CONFIGURATION
DC21X4_ERRMSG_REGISTRY
The AdapterType Registry’s key is missing or its value is unsupported by the
adapter board
NDIS_ERROR_CODE_ADAPTER_NOT_FOUND
No board matching the AdapterCFID Registry’s key value was found plugged into
the PCI bus or in the slot specified in the Registry
NDIS_ERROR_CODE_OUT_OF_RESOURCES
DC21X4_ERRMSG_ALLOC_MEMORY
Not enough memory to allocate space for the Adapter data block
NDIS_ERROR_CODE_INVALID_VALUE_FROM_ADAPTER
DC21X4_ERRMSG_SROM
Invalid data read from the adapter’s serial ROM
NDIS_ERROR_CODE_NETWORK_ADDRESS
No readable burnt_in or software configured station address
NDIS_ERROR_CODE_UNSUPPORTED_CONFIGURATION
DC21X4_ERRMSG_MEDIA
The selected media port is not supported by the board.
NDIS_ERROR_CODE_INTERRUPT_CONNECT
Interrupt initialization failed
NDIS_ERROR_CODE_TIMEOUT DC21X4_ERRMSG_LOAD_CAM
DC21X4 CAM initialization failed
Driver run time errors:
33
Download from Www.Somanuals.com. All Manuals Search And Download.
NDIS_ERROR_CODE_HARDWARE_FAILURE
DC21X4_ERRMSG_SYSTEM_ERROR
System_Error interrupt (bus parity error)
NDIS_ERROR_CODE_HARDWARE_FAILURE
DC21X4_ERRMSG_TXM_JABBER_TIMEOUT
Transmit Jabber timer expired
Windows 95
If the adapter is not detected by Windows 95 after installing the adapter, and rebooting
Windows 95, check the following:
1. Double click on My Computer/Control Panel/System to display the System Properties
Page.
2. Select the Device Manager tab from the System properties page in order to view the list
of devices in the PC.
3. Check in the list of devices for an entry labeled Other Devices. If an Other Devices
entry exists, double click on it to display the list of devices under it.
4. Check the list for an entry labeled PCI Ethernet Controller. If this exists,
select/highlight it by clicking on it and then click on the Remove button at the bottom
of the page to delete it.
5. Reboot the PC and the adapter should now be detected.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D:
Adapter Specifications
ITI-5232E Four Port 10/100 Ethernet PCI adapter
PCI 32-bit bus master
Bus Interface
ITI-5232E-N - supports shared interrupts
ITI-5232E-O/U – does not support shared interrupts
Assigned by BIOS
Hardware Interrupts
Base I/O Addresses
Data Transfer Rates
Power Requirements
Up to 800 Mbps in Fast full duplex mode
PCI Universal 3.3 or 5 volts at 17 watts
Environmental
Operating Temperature
Humidity
Altitude
Ethernet Standards
0° to 55° C
5% to 85% non-condensing
3000m maximum
IEEE 802.3 10 Base-T
IEEE 802.3u 100 Base-T
FCC Class B
Certifications
CE Class B
(4) RJ-45 female
Electrical Connections
Physical Dimensions
9.0” X 4.125”
10 Mbps
20 Mbps Full duplex
100 Mbps
Network Speeds Supported
per Ethernet Network
Segment
200 Mbps Full duplex
Link
Indication LEDs
Activity
100TX link
36
Download from Www.Somanuals.com. All Manuals Search And Download.
|