T
E
C
H
N
I
by
International Floors of America, Inc.
C
A
L
M
A
N
U
A
L
O
C
T.
2
0
0
2
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Important:
To preserve the warranty and deliver the best possible installation to your customer, follow the instructions
in this manual.
Safety Warning:
Centiva vinyl tile contains no asbestos fibers. When removing existing resilient floor coverings, carefully
observe the following warning:
Existing resilient floor coverings and black asphalt adhesive may contain asbestos. Improper procedures
used to remove these products could release asbestos fibers into the air. Asbestos fibers, if inhaled, may
cause serious bodily harm. Do not sand or dry-scrape these materials. A preferred alternative to removal
is to install a new floor over the old asbestos-containing floor whenever possible. If removal of existing
floor covering is necessary, be sure that all precautions are taken and proper procedures are followed. For
information regarding proper removal procedures, please consult Centiva or the Resilient Floor Covering
Institute, 401 East Jefferson Street, Suite 102, Rockville, MD 20850, phone: 301-640-8580. Check state and
local laws regarding removal of asbestos-containing materials.
Product:
IFA manufactures Centiva homogenous and wear-layered products for heavy commercial or residential
usage. Centiva offers unlimited choices of color, texture, style, and design. Centiva can be installed on
concrete, over underlayment panels such as Structurwood, Multiply, and Masonite brand underlayments.
Particleboard, strand board and flake board are NOT RFCI recommended underlayments; therefore, they
are not recommended as a subfloor for Centiva tiles and planks. Concrete subfloors need to be tested to
determine if the concrete’s moisture content is within the specified parameters.
Imperfections:
IFA prides itself on not packaging any products with defects. All Centiva products are closely inspected
prior to shipping. If a defect is detected, the installer should contact the supplier immediately.
Labor Policy
Not Reimbursable: Claims filed for materials that were/are installed with obvious defects
Materials that were/are installed under improper conditions
Materials that were/are installed incorrectly
Materials that were/are used for any non-flooring purpose
Storage
and Handling:
Proper storage is necessary to ensure the best performance and appearance from Centiva tiles and
adhesives.
o
o
A) Storage temperature range 65 F. -75oF. Avoid installations with tile temperatures above 80 F. and
below 60 oF.
B) Loosely lay tiles in the room or area prior to spreading adhesive to observe overall appearance.
C) The installation contractor must check to make sure all tiles and adhesives are correct for the job.
D) Always lay tiles or planks flat.
Installation
Temperatures:
A) Acclimate to the site conditions for at least 2 days (48 hours) prior to installation.
o
B) Be sure floor level temperatures are between 65 F. -75oF. for a minimum of 48 hours before
installation, during installation and afterward.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT CHARACTERISTICS
Classic Series*
Homogeneous:
Centiva manufactures homogeneous products for heavy commercial or residential usage. These tiles are
solid vinyl tiles with a standard gauge of 1/8” (3mm).
Multi-layered/Chip
Construction:
Specially developed products in multi-layered sheet form including a recycled backing and high-density wear
layer with a standard gauge of a minimum .30mil (0.8 mm) and/or chip construction throughout.
*Manufacturing of the Classic Series involves many handcrafted steps. This guarantees each tile receives a random,
natural look.
Event Series
Multi-layered &
Film Photograph:
Specially developed wear layered products are made with at least a .30 mil (0.8 mm) high density, clear PVC
wear layer.
All solid vinyl tiles, as well as the wear layer vinyl tiles and planks, have a standard gauge of 1/8”.
Classic &
Event Series
Color &
Textures:
Centiva is available in a wide range of colors and textures, reproducing the look of natural woods, stones,
ceramics and artistic designs. Textures include slate, smooth, granite, embossed, frost, tick and rustic.
Special attention should be paid when selecting a floor for your specific needs. All products can be
customized to fit your specific needs in other colors, sizes, surfaces and gauges. See charts for specific
textures and sizes.
Special Edge
Treatments:
Centiva special edge treatments include square edge, slight bevel, and regular bevel.
Applications:
All Centiva products can be used for commercial and residential use. The use of IFA adhesive is required in
order to validate the warranty for Centiva tiles or planks. Detailed instructions are listed in the installation
pages of the manual. After installation, a sealer and/or finisher is recommended for easy maintenance.
Samples:
Samples are cut from standard tiles and therefore do not correspond exactly to the pattern of the entire
tile. Samples may vary slightly from actual production runs. For critical color match, please check actual
production runs. Chain sets are available upon request. Colors shown in brochures and any other printing
are only as accurate as four color printing process will allow.
PRODUCT ABBREVIATIONS
Product
Surface
Edge Treatment
Coral Reef
Magics
Italian Marble
Concrete
CR
MG
IS
CC
NT
US
UP
PW
ST
HY-GW
HY-BB
HY-RR
HY-SD
HY-DD
CT
Slate
SS
GS
JS
Square Edge
Slight Bevel
Standard Bevel
SE
SB
BE
Smooth
Granite
Embossed
Frost
Tick
Rustic
ES
New Terrazzo
U.S. Solids
Ultraplank
Plankwood
Ultrastone
Good Ole Woods
Bamboo
RiverRock
SandStone
DesertDune
C-Tech
FR
TK
RU
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT SIZE AND PACKAGING:
Size in Inches
Classic Series
Product
Coral Reef
9 x 9
9 x 9
9 x 9
9 x 9
12 x 12 12 x 18 18 x 18 18 x 36
12 x 12 12 x 18 18 x 18 18 x 36
12 x 12 12 x 18 18 x 18 18 x 36
12 x 12 12 x 18 18 x 18 18 x 36
18 x 18
4 x 36
4 x 36
4 x 36
4 x 36
6 x 36
6 x 36
6 x 36
6 x 36
36 x 36
36 x 36
36 x 36
36 x 36
Magics
Italian Marble
Concrete
New Terrazzo
U.S. Solids
9 x 9
12 x 12 12 x 18 18 x 18 18 x 36
4 x 36
6 x 36
36 x 36
Pieces Per Carton
Sq. Ft. Per Carton
Weight Per Carton
80
45
45
45
30
45
20
45
10
45
45
45
30
45*
10
90**
38 lbs.
38 lbs.
38 lbs.
38 lbs.
38 lbs.
38 lbs.
30 lbs.
94 lbs.
Event Series
Product
Size in Inches
Ultraplank
4 x 36
Plankwood
Ultrastone
Good Ole Woods
Bamboo
6 x 36
12 x 12
18 x 18
36 x 36
4 x 36
4 x 36
RiverRock
12 x 12
12 x 18
12 x 12
18 x 18
18 x 18
36 x 36
36 x 36
SandStone
DesertDune
Pieces Per Carton
Sq. Ft. Per Carton
Weight Per Carton
45
45
24
36
45
45
30
45
45
45
10
90**
47 lbs.
47 lbs.
47 lbs.
47 lbs.
47 lbs.
94 lbs.
*All products in the Classic Series are packaged in 45 sf cartons.
**For larger projects, slabs of 36” x 36” may be put on pallets rather than in cartons with a
maximum of 240 slabs = 2,160 s/f
Additional sizes available upon request.
Please refer to the Abbreviation Chart for all abbreviations and surface textures.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CENTIVA PRODUCT SPECIFICATIONS
Commercial
and Residential:
All material shall be Centiva by International Floors of America, Inc. Every style has a 10-character code. The first
two characters represent the style, the next four are the color number, the next two are the surface, and the last two
are the selected edge XX - XXXX - XX – XX in size XX” x XX”
Centiva products shall only be installed with the IFA recommended adhesives. It is
recommended that a coating with a sealer and/or a finisher is used for floor protection.
CLASSIC SERIES
Italian Marble
Construction:
Standard Sizes:
Gauge:
Pure solid vinyl
9” x 9”, 12” x12”, 18” x 18”, and 36’ x 36’ slabs; custom sizes
1/8”
Wearlayer:
Packaged:
Homogeneous throughout
45 s/f per carton (9” x 9”, 12” x 12”, 18” x 18”);
90 s/f per carton of 36” x 36”
For larger projects, slabs of 36” x 36” may be put on pallets rather than in cartons with a
maximum of 240 slabs = 2,160 s/f
47 lbs per 9” x 9” or 12” x 12” or 18” x 18” carton
94 lbs per 36” x 36” carton
Approximate Weight:
Surfaces:
Edge Treatments:
Smooth, slate or granite
Square, regular bevel or slight bevel
Standard Colors:
7 plus custom colors
Slip Resistance
Dry – Excellent 0.7100 (ASTM C1028); Wet 0.6463
SS – T – 312B, Type III
285 lbs. per square inch
Reference Specifications:
Recommended Static Load:
Taber Abrasion Test:
Fire Performance:
~ 166,000 revolutions
Critical Radiant Flux: 0.45 watts/cm2 NFPA 101 Life Safety Code
Average Dm (corrected) 450 NFPA 101 Life Safety Code
75 or less (ASTM E084)
Smoke Density:
Flame Spread:
Coral Reef
Construction:
Standard Sizes:
Gauge:
Pure solid vinyl
9” x 9”, 12” x12”, 18” x 18”, and 36’ x 36’ slabs; custom sizes
1/8”
Wearlayer:
Packaged:
Homogeneous throughout
45 s/f per carton (9” x 9”, 12” x 12”, 18” x 18”);
90 s/f per carton of 36” x 36”
For larger projects, slabs of 36” x 36” may be put on pallets rather than in cartons with a
maximum of 240 slabs = 2,160 s/f
Approximate Weight:
47 lbs per 9” x 9” or 12” x 12” or 18” x 18” carton
94 lbs per 36” x 36” carton
Smooth, slate or granite
Square, regular bevel or slight bevel
Surfaces:
Edge Treatments:
Standard Colors:
Slip Resistance
Reference Specifications:
Recommended Static Load:
Taber Abrasion Test:
Fire Performance:
10 plus custom colors
Dry – Excellent 0.7100 (ASTM C1028); Wet 0.6463
SS – T – 312B, Type III
285 lbs. per square inch
~ 166,000 revolutions
Critical Radiant Flux: 0.45 watts/cm2 NFPA 101 Life Safety Code
Average Dm (corrected) 450 NFPA 101 Life Safety Code
75 or less (ASTM E084)
Smoke Density:
Flame Spread:
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Magics
Construction:
Standard Sizes:
Gauge:
Pure solid vinyl
9” x 9”, 12” x 12”, 18” x 18”, and 36” x 36” slabs; custom sizes
1/8”
Homogeneous throughout
Wearlayer:
Packaged:
45 s/f per carton (9” x 9”, 12” x 12”, 18” x 18”); 90 s/f per carton of 36” x 36”
For larger projects, slabs of 36” x 36” may be put on pallets rather than in cartons with a
maximum of 240 slabs = 2,160 s/f
Approximate Weight:
47 lbs per 9” x 9” or 12” x 12” or 18” x 18” carton
94 lbs per 36” x 36” carton
Smooth, slate and granite
Square, regular bevel or slight bevel
12 plus custom colors
Surfaces:
Edge Treatments:
Standard Colors:
Slip Resistance
Dry – Excellent 0.7100 (ASTM C1028); Wet 0.6463
Reference Specifications:
Recommended Static Load:
Taber Abrasion Test:
Fire Performance:
SS – T – 312B, Type III
285 lbs. per square inch
~ 166,000 revolutions
Critical Radiant Flux: 0.45 watts/cm2 NFPA 101 Life Safety Code
Average Dm (corrected) 450 NFPA 101 Life Safety Code
75 or less (ASTM E084)
Smoke Density:
Flame Spread:
Concrete
Construction:
Standard Sizes:
Gauge:
Multi-layered including at least .30 mil high density wear layer and recycled backing
9” x 9”, 12” x 12”, 18” x 18”, and 36” x 36” slabs; custom sizes
1/8”
Wearlayer:
Packaged:
Clear Rigid, High-Density PVC Of .30 Mil
45 s/f per carton (9” x 9”, 12” x 12”, 18” x 18”); 90 s/f per carton of 36” x 36”
For larger projects, slabs of 36” x 36” may be put on pallets rather than in cartons with a
maximum of 240 slabs = 2,160 s/f
Approximate Weight:
47 lbs per 9” x 9” or 12” x 12” or 18” x 18” carton
94 lbs per 36” x 36” carton
Surfaces:
Edge Treatments:
Granite, slate and embossed
Square, regular bevel or slight bevel
Standard Colors:
7 plus custom colors
Slip Resistance
Dry – Excellent 0.7100 (ASTM C1028); Wet 0.6463
SS – T – 312B, Type III
285 lbs. per square inch
~ 27,000 revolutions (wear layer products)
Critical Radiant Flux: 0.45 watts/cm2 NFPA 101 Life Safety Code
Average Dm (corrected) 450 NFPA 101 Life Safety Code
75 or less (ASTM E084)
Reference Specifications:
Recommended Static Load:
Taber Abrasion Test:
Fire Performance:
Smoke Density:
Flame Spread:
U.S. Solids
Construction:
Standard Sizes:
Gauge:
Multi-layered with at least .80 mil colored top layer and recycled backing
9” x 9”, 12” x 12”, 18” x 18”, and 36” x 36” slabs; custom sizes
1/8”
45 s/f per carton (9” x 9”, 12” x 12”, 18” x 18”); 90 s/f per carton of 36” x 36”
For larger projects, slabs of 36” x 36” may be put on pallets rather than in cartons with a
maximum of 240 slabs = 2,160 s/f
Packaged:
Approximate Weight:
47 lbs per 9” x 9” or 12” x 12” or 18” x 18” carton
94 lbs per 36” x 36” carton
Surfaces:
Edge Treatments:
Smooth, slate, granite, and embossed
Square, regular bevel or slight bevel
Standard Colors:
18 plus custom colors
Slip Resistance
Dry – Excellent 0.7100 (ASTM C1028); Wet 0.6463
SS – T – 312B, Type III
285 lbs. per square inch
Reference Specifications:
Recommended Static Load:
Taber Abrasion Test:
Fire Performance:
~ 110,000 revolutions
Critical Radiant Flux: 0.45 watts/cm2 NFPA 101 Life Safety Code
Average Dm (corrected) 450 NFPA 101 Life Safety Code
75 or less (ASTM E084)
Smoke Density:
Flame Spread:
7
Download from Www.Somanuals.com. All Manuals Search And Download.
New Terrazzo
Construction:
Standard Sizes:
Through layers of encapsulated chips including recycled backing
18” x 18”
Gauge:
Packaged:
Approximate Weight:
1/8”
45 s/f per carton (18” x 18”)
47 lbs per 18” x 18” carton
Smooth
Surfaces:
Edge Treatments:
Standard Colors:
Slip Resistance
Square
5 plus custom colors*
Dry – Excellent 0.7100 (ASTM C1028); Wet 0.6463
SS – T – 312B, Type III
285 lbs. per square inch
Reference Specifications:
Recommended Static Load:
Taber Abrasion Test:
Fire Performance:
Smoke Density:
~ 110,000 revolutions
Critical Radiant Flux: 0.45 watts/cm2 NFPA 101 Life Safety Code
Average Dm (corrected) 450 NFPA 101 Life Safety Code
75 or less (ASTM E084)
Flame Spread:
EVENT SERIES
ULTRASTONE Plaza
Construction:
Standard Sizes:
Gauge:
Solid Vinyl Tile
12” x12”, 18” x 18”, and 36” x 36” slabs; custom sizes
.120 mil (3mm)
Wearlayer:
Packaged:
Clear Rigid, High-Density PVC of .30 Mil
45 s/f per carton (12” x 12”, 18” x 18”); 90 s/f per carton of 36” x 36”
For larger projects, slabs of 36” x 36” may be put on pallets rather than in cartons with a
maximum of 240 slabs = 2,160 s/f
Approximate Weight:
47 lbs per 12” x 12” or 18” x 18” carton
94 lbs per 36” x 36” carton
Surfaces:
Edge Treatments:
Standard Colors:
Frost
Square or slight bevel
8 plus custom colors*
Slip Resistance
D-2047-82 Static Coefficient of Friction on wet and dry surfaces
ASTM E-648 .45 Watts/cm2 or less; NFPA 101 Life Safety Code Class I Passes
285 lbs. per square inch
ASTM E-662 450 or less in flaming mode, Passes
75 or less (ASTM E-84) Class B Passes
Critical Radiant Flux:
Recommended Static Load:
Smoke Generation:
Flame Spread:
ULTRASTONE Terra
Construction:
Standard Sizes:
Gauge:
Solid Vinyl Tile
12” x12”, 18” x 18”, and 36” x 36” slabs; custom sizes
.120 mil (3mm)
Wearlayer:
Packaged:
Clear Rigid, High-Density PVC of .30 Mil
45 s/f per carton (12” x 12”, 18” x 18”); 90 s/f per carton of 36” x 36”
For larger projects, slabs of 36” x 36” may be put on pallets rather than in cartons with a
maximum of 240 slabs = 2,160 s/f
Approximate Weight:
47 lbs per 12” x 12” or 18” x 18” carton
94 lbs per 36” x 36” carton
Surfaces:
Edge Treatments:
Standard Colors:
Granite
Square or slight bevel
8 plus custom colors*
Slip Resistance
D-2047-82 Static Coefficient of Friction on wet and dry surfaces
ASTM E-648 .45 Watts/cm2 or less; NFPA 101 Life Safety Code Class I Passes
285 lbs. per square inch
ASTM E-662 450 or less in flaming mode, Passes
75 or less (ASTM E-84) Class B Passes
Critical Radiant Flux:
Recommended Static Load:
Smoke Generation:
Flame Spread:
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRASTONE Rialto
Construction:
Solid Vinyl Tile
Standard Sizes:
Gauge:
12” x12”, 18” x 18”, and 36” x 36” slabs; custom sizes
.120 mil (3mm)
Wearlayer:
Packaged:
Clear Rigid, High-Density PVC of .30 Mil
45 s/f per carton (12” x 12”, 18” x 18”); 90 s/f per carton of 36” x 36”
For larger projects, slabs of 36” x 36” may be put on pallets rather than in cartons with a
maximum of 240 slabs = 2,160 s/f
Approximate Weight:
Surfaces:
47 lbs per 12” x 12” or 18” x 18” carton; 94 lbs per 36” x 36” carton
Frost
Edge Treatments:
Standard Colors:
Slip Resistance:
Square or slight bevel
4 plus custom colors*
D-2047-82 Static Coefficient of Friction on wet and dry surfaces
ASTM E-648 .45 Watts/cm2 or less; NFPA 101 Life Safety Code Class I Passes
285 lbs. per square inch
Critical Radiant Flux:
Recommended Static Load:
Smoke Generation:
Flame Spread:
ASTM E-662 450 or less in flaming mode, Passes
75 or less (ASTM E-84) Class B Passes
PLANKWOOD
Construction:
Standard Sizes:
Solid Vinyl Tile
6” x 36” and custom
.120 mil (3mm)
Gauge:
Wearlayer:
Clear Rigid, High-Density PVC of .30 Mil
Packaged:
Approximate Weight:
36 s/f per carton
30 lbs per carton
Surfaces:
Tick
Edge Treatments:
Standard Colors:
Slip Resistance
Square
11 plus custom colors*
D-2047-82 Static Coefficient of Friction on wet and dry surfaces
ASTM E-648 .45 Watts/cm2 or less; NFPA 101 Life Safety Code Class I Passes
285 lbs. per square inch
ASTM E-662 450 or less in flaming mode, Passes
75 or less (ASTM E-84) Class B Passes
Critical Radiant Flux;
Recommended Static Load:
Smoke Generation:
Flame Spread:
ULTRAPLANK
Construction:
Standard Sizes:
Solid Vinyl Tile
4” x 36” and custom
Gauge:
.120 mil (3mm)
Wearlayer:
Packaged:
Clear Rigid, High-Density PVC of .30 Mil
45 s/f per carton
Approximate Weight:
47 lbs per carton
Surfaces:
Tick
Slight Bevel
16 plus custom colors*
D-2047-82 Static Coefficient of Friction on wet and dry surfaces
ASTM E-648 .45 Watts/cm2 or less; NFPA 101 Life Safety Code Class I Passes
285 lbs. per square inch
ASTM E-662 450 or less in flaming mode, Passes
75 or less (ASTM E-84) Class B Passes
Edge Treatments:
Standard Colors:
Slip Resistance
Critical Radiant Flux:
Recommended Static Load:
Smoke Generation:
Flame Spread:
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Good Ole Woods/Bamboo
Construction:
Standard Sizes:
Solid Vinyl Tile
4” x 36” and custom
Gauge:
.120 mil (3mm)
Wearlayer:
Packaged:
Clear Rigid, High-Density PVC of .30 Mil
45 s/f per carton
Approximate Weight:
47 lbs per carton
Surfaces:
Tick/Frost/Rustic
Slight Bevel
Edge Treatments:
Standard Colors:
Slip Resistance
9 and 2 plus custom colors*
D-2047-82 Static Coefficient of Friction on wet and dry surfaces
ASTM E-648 .45 Watts/cm2 or less; NFPA 101 Life Safety Code Class I Passes
285 lbs. per square inch
ASTM E-662 450 or less in flaming mode, Passes
75 or less (ASTM E-84) Class B Passes
Critical Radiant Flux;
Recommended Static Load:
Smoke Generation:
Flame Spread:
RiverRock/DesertDune
Construction:
Standard Sizes:
Gauge:
Solid Vinyl Tile
12” x12”, 18” x 18”, and 36” x 36” slabs; custom sizes
.120 mil (3mm)
Clear Rigid, High-Density PVC of .30 Mil
45 s/f per carton (12” x 12”, 18” x 18”);
90 s/f per carton of 36” x 36”
Wearlayer:
Packaged:
For larger projects, slabs of 36” x 36” may be put on pallets rather than in cartons with a
maximum of 240 slabs = 2,160 s/f
Approximate Weight:
47 lbs per 12” x 12” or 18” x 18” carton
94 lbs per 36” x 36” carton
Surfaces:
Edge Treatments:
Standard Colors:
Rock/Granite
Square or slight bevel
5 and 5 plus custom colors*
Slip Resistance:
D-2047-82 Static Coefficient of Friction on wet and dry surfaces
ASTM E-648 .45 Watts/cm2 or less; NFPA 101 Life Safety Code Class I Passes
285 lbs. per square inch
ASTM E-662 450 or less in flaming mode, Passes
75 or less (ASTM E-84) Class B Passes
Critical Radiant Flux:
Recommended Static Load:
Smoke Generation:
Flame Spread:
SandStone
Construction:
Standard Sizes:
Gauge:
Solid Vinyl Tile
12” x18”, and 36” x 36” slabs; custom sizes
.120 mil (3mm)
Wearlayer:
Packaged:
Clear Rigid, High-Density PVC of .30 Mil
45 s/f per carton (12” x 18”);
90 s/f per carton of 36” x 36”
For larger projects, slabs of 36” x 36” may be put on pallets rather than in cartons with a
maximum of 240 slabs = 2,160 s/f
47 lbs per 12” x 18” carton
Approximate Weight:
94 lbs per 36” x 36” carton
Surfaces:
Edge Treatments:
Rock/Granite
Square or slight bevel
Standard Colors:
Slip Resistance:
Critical Radiant Flux:
Recommended Static Load:
Smoke Generation:
Flame Spread:
2 plus custom colors*
D-2047-82 Static Coefficient of Friction on wet and dry surfaces
ASTM E-648 .45 Watts/cm2 or less; NFPA 101 Life Safety Code Class I Passes
285 lbs. per square inch
ASTM E-662 450 or less in flaming mode, Passes
75 or less (ASTM E-84) Class B Passes
*In the Event Series, custom colors require a minimum order of 10,000 S/F per color.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Commercial
& Residential
There are three (3) basic requirements necessary to assure a long lasting, attractive Centiva® floor:
1.
2.
3.
Proper Subfloor Preparation
Installation
Adhesives
The following guidelines will help to ensure complete satisfaction with your installation by fulfilling these
requirements. Centiva tiles and planks are suitable for surfaces on above and below grade. Centiva can be
installed over concrete or wood subfloors.
1.0 SUBFLOOR PREPARATION
1.1 Testing
A calcium chloride test (moisture test) is essential on all concrete floors. This test should be performed in several areas: the
perimeter of the room, at columns, and wherever else moisture might occur. The moisture level from the concrete should
not exceed 3.0 lbs./1000 sq. ft. in a 24 hour time period. If the concrete exceeds the moisture limitations, the installation
should not proceed until the problem is corrected. A moisture problem can be corrected by sealing the concrete with any of
the many brands of concrete sealers available. After the sealer has been applied, always retest to ensure that the problem has
been corrected. A moisture test indicates the conditions at the time of testing only. The flooring contractor cannot be held
responsible if the moisture appears in the future causing adhesive failure. A new concrete floor contains a high percentage of
moisture; therefore, it must be allowed adequate drying time. This drying time normally requires 28 to 30 days, but it can vary
depending on several conditions such as the type of concrete used, average air temperature, and the thickness or location of
the slab.
1.2 Preparation
New Floors
Underlayment panels can be used to correct deficiencies in the subfloor and to provide a smooth, sound surface for Centiva tiles and planks.
There are numerous suitable underlayment panels such as Structurwood, Multiply, and Masonite brand underlayments. The
most common of these is ¼” APA underlayment grade plywood. Particleboard, strand board and flake board are NOT RFCI
recommended underlayments; therefore, they are not recommended as a subfloor for Centiva tiles and planks.
Always fasten underlayment panels in accordance with the manufacturer’s recommendations because any
failure of the underlayment or Centiva flooring as a result of the underlayment is the responsibility of the
underlayment manufacturer and installer. Suitable underlayment with a fully sanded surface and a minimum
thickness of ¼” is preferred. Always make sure that the subfloor is free of any foreign material such as dust,
grease, oil, polish, and loose material that may cause staining, telegraphing, or adhesive failure.
Concrete subfloors are acceptable as long as the concrete’s moisture content is within the specified
parameters.
A Portland based patching compound or leveler should be used to cover seams, cracks, indentations, and subfloor
irregularities. Calcium sulfate/plaster/gypsum based compounds are NOT recommended as they may harbor and promote
mildew growth, offer poor bond and adhesion strength, and/or have low indentation resistance.
1.3 Preparation
Existing Floors
Centiva vinyl tile or planks contain no asbestos fibers. When removing existing resilient floor coverings,
carefully observe the following warning:
Existing resilient floor coverings and black asphalt adhesive may contain asbestos. Improper procedures used to remove these
products could release asbestos fibers into the air. Asbestos fibers, if inhaled, may cause serious bodily harm. Do not sand or
dry scrape these materials. A preferred alternative to removal is to install a new floor over the old asbestos-containing floor
whenever possible. If removal of existing floor covering is necessary, be sure that all precautions are taken and proper
procedures are followed. For information regarding proper removal procedures, please consult Centiva or the Resilient Floor
Covering Institute, 401 East Jefferson Street, Suite 102, Rockville, MD, 20850, phone: 301-640-8580. Check state and local
laws regarding removal of asbestos-containing materials.
After removing existing flooring, make sure to remove also old cutback adhesive, grease, wax, or other foreign matter.
Painted and/or varnished surfaces must be sanded and dust free. In some cases old concrete subfloors must be shot blasted
and a floor leveler should be applied prior to installation. Poor subfloor preparation may telegraph later on through the
Centiva flooring causing visible irregularities. Between floor prep and start of installation, make sure to keep the floor dry, free
from dirt, dust and grit.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2.0 INSTALLATION
Before any installation takes place, please read the following information carefully:
−
−
All Centiva tiles and planks should be present at the jobsite for 48 hours at a temperature between 68-72 degrees F in
order to acclimate properly. Avoid installations with temperatures above 80 degrees F and below 60 degrees F. All
Centiva tiles and planks are duplications of natural or real products; therefore, shades and pattern variations will occur.
The Classic Series, including Coral Reef, Magics, Italian Style Marble, Concrete and New Terrazzo, achieves its natural
and realistic appearance through its variations. The Centiva Classic Series is a non-directional floor tile! The product
should be pre-blended before installation begins. This is similar to shuffling a deck of cards, and the purpose is to make
the different shades and patterns occur at random. As larger the floor tile (12” x 12”, 18”x 18” or 36”x 36”) less blend is
possible in ratio to the size of the room.
−
The Event Series with its products Ultrastone (Plaza, Rialto and Terra), Ultraplank, Plankwood and Harmony Line is a
multi-layered, solid vinyl tile and plank with a film photographic design and high density commercial wear layer of .30 mil
(0.8 mm metric). Please pay attention to the backside of the tile of Ultrastone. Plaza and Rialto have as standard a frost
finish surface. Due to light reflection, shine difference could occur if the tiles do not get placed in a certain direction.
Therefore we recommend the following installation pattern:
Cross Joint Installation
½ Off Installation
↔
↨
↨
↔
↨
↔
↨
↔
↨
↨
↨
↨
↨
↨
↨
↨
↨
↨
↨
↨
↨
↨
↨
Remember:
This procedure is
↨
↨
↨
↨
↨
↨
↨
recommended only for tile
in the Event Series with
frost finish (FR) only.
(Standard for Ultrastone
Plaza and Rialto)
↔
↨
↔
↨
↔
↨
↔
↨
↔
↔
↨
↨
2.1 Calculating
The number of tiles you will need:
Measure the room’s length and width. Multiply the width times the length to get the square footage. Measure all offsets and
alcoves separately, and add the square footage for each area to arrive at the total square footage. All Centiva products come
standard in three sizes: 12-inch squares, 18-inch squares and 36-inch squares. Each 12-inch tile covers one square foot, so
when you figure the number of square feet in the installation area, you already know how many tiles you need. Add 5%
allowance for cutting waste and always round up to the next full carton (45 sq. ft.).
An 18-inch tile covers 2.25 sq. ft. Simply take your total square footage and divide it by 2.25. Again, add 5% for waste.
A 36-inch slab covers 9 sq. ft. Slabs are mostly used for larger applications and waste should be considered between 5 – 8%.
Slabs are boxed in 90 sq. ft. cartons.
Centiva also offers other sizes, such as 9” x 9”, 12” x 18”, 12” x 36”, and 18” x 36”.
2.2 Feature
Strips:
Feature Strips around a tile are easy to calculate.
You will need 2 linear ft. for each 12-inch tile
“
“
“
“
“
“
3 linear ft for each 18-inch tile
6 linear ft for each 36-inch slab
To figure out quantity on Centiva Floor Design patterns please ask your Centiva representative or call
1-800-633-3380.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Laying Out The Job Site Using Centiva
Classic And Event Series Tiles or Slabs
2.4 Diagonal Layout For Centiva Classic
And Event Series Tiles Or Slabs
Carefully determining where to begin your tile installation results
in the most professional looking job. Always try to end up with
at least half a tile at each wall for best appearance.
Extra measurements and guidelines are needed for
diagonal installations. A sketch is useful for any
complicated installation. Follow these guidelines for
diagonal installations:
Follow these steps:
Figure 1.
Figure 1.
1. Treat the room as
rectangle, disregarding
offsets, alcoves, etc. Find
the center points of the two
end walls and strike a chalk
line between them.
1. Divide the room into equal
quarter sections and adjust
the same way you would
for normal installations.
Figure 2
Figure 2.
4’3”
2. Find the center of the chalk
line, using T-square or a
Centiva tile to line up.
2. Measure and mark a
point 4’3” from the
center point on
Strike a second chalk line at
right angles to the first one.
The room is now divided
into four equal parts.
each centerline.
Snap a chalk line to
connect the four
new points.
Figure 3
Figure 3..
3. Starting in center of room
where the two chalk lines
intersect, loose lay several
tiles in a row to one end of
wall and a second row to a
sidewall. Measure distance
from last tile to wall. If it is
less than half a tile, move
centerline on half a tile
3. Mark the midpoint on
the new guidelines
and snap another
chalk line to its
opposite midpoint.
These lines should
intersect the original
center point or the
measurements will be
incorrect.
nearer the opposite wall.
Do this in both directions.
Figure 4.
4. Use the guidelines
for the installation.
Nine 12-inch tiles,
four 18-inch tiles or
one 36-inch slab will
start towards all four
directions.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 Layout Of Room Using Centiva Event Series
Ultraplank, Plankwood, Good Ole Woods Or
Bamboo
2.6 Laying Of The Plank
Spread adhesive following the specific recommendations for the adhesive
outlined in the Adhesives section of the manual. Place the first piece of
plank at the junction of the chalk lines. Continue to lay the plan, making
sure each plank is flush against the chalk line and tight against the adjoining
plank. Make sure the plank is well seated into the adhesive, paying special
attention to the edges. Lay row by row, or in a pyramid fashion.
Pyramid Fashion
Find the center point of the room. Strike a line (A-B).
Figure 1.
A
B
A
B
Obtain a true 90o angle by using a carpenter’s square. Strike a
second line, which will divide the room into four equal parts.
Measure the distance from the center to the wall parallel to the
direction of the plank. Divide that measurement by the width of
a plank (3”). If less than half a plank (1 ½”) remains as the
border plank, adjust the point by 1 ½”. This will give a large
border along the wall and reduce the chance of having to cut a
small sliver of flooring to place along the wall.
Row by Row Fashion
Figure 2.
A
B
*Row by row fashion installation specially recommended when using
IFA D-2001Wet Set Adhesive.
This is the incorrect way to lay the plank!
A
B
Centiva Vinyl Plank features beveled and square edges to accent
individual planks and create a distinct plank effect. For this
reason, anytime you make a cut, you will want to place that cut
edge along a wall. Placing a cut edge against the uncut edge of
another piece of flooring will not look natural or realistic.
However, for special patterns, the floor may be installed cut edge
to cut edge and beveled edge to beveled edge for a consistent and
finished look.
A
B
Fitting the Border:
Measure the distance from the last plank in the row to the wall. Mark the
plank and cut it against the mark. Lay the plank in place, making sure the
cut edge is against the wall.
Figure 3.
Fitting Around Irregular Objects:
First Plank
Make a pattern out of heavy paper to fit around pipes and other
irregularities. Place the pattern on the plank, trace, cutting along the trace
lines with scissors or a sharp knife. Place the cut plank into position.
The manufacturer or supplier will not be liable for any loss, damage, or complaint
of any kind if the specific procedures in the Installation Guidelines are not
followed.
A
B
14
Download from Www.Somanuals.com. All Manuals Search And Download.
2.7 Useful Installation Tips:
•
Intricate cuts around door frames, cabinets, transitions, etc. It is always recommended to fit in prior to
spreading adhesive. See also adhesive pages.
•
Have several clean white cloths and a container of denatured alcohol or mineral spirits available for cleaning
off excess adhesive from the tile as you work. Any excess adhesive must be removed from the tile surface, in
between tile seams, or the surrounding area WHILE STILL WET. IFA’s D-2001 and IFA PS-5000 may be
cleaned with soap and water while still wet, BUT IFA’s EP-2000H may only be cleaned with mineral spirits or
denatured alcohol WHILE STILL WET. DO NOT ALLOW ADHESIVE TO DRY ON TILE SURFACE. To
obtain best results, dampen a clean cloth with cleaner and gently rub areas as to not move the tiles out of
place. Do not saturate the area with cleaner and make sure that you clean up any excess cleaning solution as
you go.
•
Never begin installation when all necessary tools are not available. (straight edge knife, curved edge knife,
ruler, trowel, roller, etc.)
2.8 CFD (Centiva Custom Floor Design)
Please contact your Centiva representative for more information.
•
3.0 ADHESIVES
IFA recommends all tiles and planks be installed with IFA adhesives only. Please choose the following adhesives
that apply to your specific job specifications. Attention: The use of dry set IFA PS 5000 is for installation of the
Event Series only. IFA PS 5000 is not to be used for Centiva Classic Series.
3.1 QUICK, HANDY ADHESIVE REFERENCE GUIDE
Adhesive
D-2001
PS-5000
EP-2000
Installation
Sub-floor
wet set
Porous only
No
pressure sensitive, dry set
porous or non-porous
Yes
epoxy mix
porous or non-porous
Yes
Over old vinyl
Trowel size
1/16x1/16x1/16 sq. notch
Porous - 1/16x1/16x1/16 V-notch or roller
Non-porous - 1/32x1/32x1/32 V-notch or roller
~220-260 sq. ft. per gallon
2 hours
1/16x1/16x1/16 sq. notch
spread rate
open time
roller
~125 sq. ft. per gallon
20 minutes
~110 sq. ft. per gallon
varies
100 lb.
100 lb.
150 lb.
max. moisture
Centiva Floor
3 lbs/1,000 s.f. in 24 hours
Classic or Event
3 lbs/1,000 s.f. in 24 hours
EVENT ONLY
3 lbs/1,000s.f. in 24 hours
Classic or Event
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 IFA D-2001 Vinyl Plank & Luxury Vinyl Tile Flooring Adhesive
Description
& Data:
IFA D-2001 adhesive is solvent-free, non-flammable, freeze/thaw stable, and nearly odor-free. It can be used
where other adhesives might present potential health risks. It is suitable for office buildings, hotels, hospitals,
schools, restaurants, nursing homes, etc. IFA D-2001 adhesive contain one or more micro-biocides to inhibit the
growth of mold and mildew. IFA D-2001 can be used to install luxury vinyl tile and vinyl plank flooring over
porous floors. It exhibits quick grab, excellent moisture resistance, and spreads easily. DO NOT use over
existing resilient flooring or painted sub-floors. Not for use over non-porous floors such as sealed concrete,
metal, existing sheet flooring, etc. Only IFA adhesive is to be utilized for installing Centiva flooring.
Surface
Preparation:
Use on grade, above grade, or below grade (if the floor covering is recommended for below grade installations).
May be used over plywood and concrete. Use a high quality latex/Portland cement based-type patching
compound to fill or level any irregular areas. The floor must be sound, dry, and free from dirt, dust, old
adhesives, grease, wax, or other foreign matter. Painted or varnished surfaces must be sanded and dust-free.
Concrete floors must be fully cured, free from dust, moisture, excessive alkalinity, curing agents, and excessive
moisture vapor emissions (3 lbs. /1,000 SF/24 hrs.) On- and below-grade concrete must have a satisfactory
moisture barrier beneath the slab. Do not use IFA D-2001 where moisture is present in the concrete sub-floor;
moisture may retard or prevent the adhesive from setting. If applying over old cutback, all old adhesive must be
removed so that the floor is smooth.
Application:
The sub-floor, flooring material, and adhesive should be maintained at a minimum temperature of 68-
72 degrees F. for 48 hours prior to, during, and after installation. Apply the adhesive with a 1/16” x
1/16” x 1/16” square notched trowel in small sections. Apply only that amount of adhesive that can
be covered in 20 minutes. That open time will vary with the temperature, humidity, and porosity of
the sub-floor. For best results let the adhesive tack up before installing the planks or tile but install
them before the adhesive skins over or begins to dry. Position planks or tile firmly in the adhesive
without sliding them. Check open time periodically by lifting a section just laid to be certain that at
least 95% of the adhesive pattern has been transferred to the back of the planks or tile. If the
adhesive begins to set up or skin over, scrape it up and re-apply fresh adhesive. Roll each section
immediately upon completion with a 100 lb. sectional roller. Re-roll the entire floor after one or
two hours. Restrict heavy foot traffic or rolling loads for at least 24 hours. DO NOT WASH OR
WAX THE FLOOR FOR A MINIMUM OF 48 HOURS AFTER INSTALLATION.
Limitations:
Clean-up:
Store indoors only. Protect from freezing. Adhesive is freeze/thaw stable to 10 degrees F.
Prolonged or repeated freeze/thaw cycles should be avoided. Should adhesive freeze, allow to thaw
at room temperature and stir well before using. The finished installation must be protected from
moisture and/or freezing for a minimum of 48 hours. Not for use over non-porous floors.
Dried adhesive can be difficult to remove; take care to remove wet adhesive from the surface of the
flooring before it dries. Fresh adhesive (and dried adhesive on resilient flooring) can be removed
with a soapy, wet cloth. Dried adhesive can be removed from carpet with a non-flammable cleaning
solvent.
Coverage:
Approximately 125 square feet per gallon. Coverage will vary with the type of floor covering and job
conditions.
Product Specs:
Base: Latex
Weight: 9.3 lbs/gal Shelf Life:
Open Time: 20 Minutes
Color: Cream
One Year, Unopened
Consistency: Medium Paste
VOCs: -0- Calculated
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 IFA PS-5000 Pressure Sensitive Vinyl Tile and Plank Adhesive
Description
& Data:
PS-5000 adhesive is solvent-free, non-flammable, freeze/thaw stable, and nearly odor-free. It can be used where
other adhesives might present potential health risks. It is suitable for office buildings, hotels, hospitals, schools,
restaurants, nursing homes, etc. PS-5000 adhesive contains one or more micro-biocides to inhibit the growth of
mold and mildew. PS-5000 should be used to install Centiva Vinyl Products Event Series and Harmony Line.
(ULTRASTONE, ULTRAPLANK, PLANKWOOD, GOOD OLE WOODS, BAMBOO, RIVER ROCK, DESERT
DUNE AND SANDSTONE.) UNDER NO CIRCUMSTANCES SHOULD IFA PS-5000 BE USED FOR THE
CENTIVA CLASSIC SERIES. It spreads easily, exhibits quick grab, and has excellent resistance to moisture and
plasticizer migration. Only IFA adhesive is to be utilized for installing Centiva flooring.
Surface
Preparation:
Use on grade, above grade, or below grade (if the floor covering is recommended for below grade installations).
May be used over plywood, concrete, terrazzo, steel, and well-bonded, wax-free floor coverings. Use a high
quality latex/Portland cement based-type patching compound to fill or level any irregular areas. Never sand
resilient floors; they may contain asbestos. The floor must be sound, dry, and free from dirt, dust, old
adhesives, grease, wax, or other foreign matter. Concrete floors must be fully cured, free from dust, moisture,
excessive alkalinity, curing agents, and excessive moisture vapor emissions (3 lbs. /1,000 SF/24 hrs.) On- and
below-grade concrete must have a satisfactory moisture barrier beneath the slab. Do not use PS-5000 where
moisture is present in the concrete sub-floor; moisture may retard or prevent the adhesive from setting. May
be used over old cutback adhesive provided that the old adhesive is removed and the floor is smooth.
Application:
The adhesive, tile, and room should be maintained at a minimum temperature of 68-72 degrees F. for 48 hours
prior to, during, and after installation. For porous sub-floors apply the adhesive with a 1/16” x 1/16” x 1/16”
V-notched trowel; for non-porous sub-floors use a 1/32” x 1/32” x 1/32” V-notched trowel. Immediately after
spreading the adhesive, roll it with a short nap roller dampened with adhesive to flatten the adhesive ridges.
This procedure will ensure that the trowel notch pattern does not telegraph through to the finished floor.
When using the “wet method” of installation test the adhesive to see if it has “strings” and is moist to the touch
before installing the floor covering. Check periodically to make sure there is full transfer to adhesive to the
back of the floor covering. When using the “tacky” method of installation, allow the adhesive to become tacky
before beginning the installation (adhesive should not transfer to the finger when touched). That set-up time
will vary with the temperature, humidity, and porosity of the sub-floor. To test, touch the adhesive lightly; if it
does not transfer to your finger, proceed with the installation. Place the tiles into the adhesive within two
hours of spreading. (Place carefully and accurately because the tiles cannot be repositioned easily). Within an
hour of installation roll the entire floor with a 100 lb. roller. Roll at least twice, once in each direction. Restrict
heavy foot traffic or rolling loads for at least 24 hours.
Limitations:
Clean-up:
Store indoors only. Protect from freezing. Adhesive is freeze/thaw stable to 10 degrees F. Prolonged or
repeated freeze/thaw cycles should be avoided. Should adhesive freeze, allow to thaw at room temperature and
stir well before using. The finished installation must be protected from moisture and/or freezing for a minimum
of 48 hours.
Dried adhesive can be difficult to remove; take care to remove wet adhesive from the surface of the tiles before
it dries. Fresh adhesive can be removed with a soapy, wet cloth. DO NOT FLOOD. DO NOT USE
SOLVENTS AS CLEANING AGENTS. DO NOT ALLOW ADHESIVE TO DRY ON FLOOR
COVERING BECAUSE EFFORTS TO REMOVE IT MAY CAUSE DAMAGE TO THE FLOOR
COVERING.
Coverage:
Approximately 220-260 square feet per gallon. Coverage will vary with the type of floor covering and job
conditions.
Product Specs:
Base: Acrylic Latex Color: White
Shelf Life: One Year, Unopened;
Consistency: Thin Paste;
VOCs: -0- Calculated
Weight/Gal: 8.45 lbs.
Open Time: 60 Minutes
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4 IFA EP-2000 Epoxy Adhesive (Solvent Free)
Description
Parts A & B
& Data:
IFA EP-2000 adhesive is solvent-free, non-flammable, and nearly odor-free. It can be used where other
adhesives might present potential health risks. It is suitable for use in office buildings, hotels, hospitals, schools,
restaurants, nursing homes, etc. IFA EP-2000 is recommended for the installation of vinyl flooring products on
approved sub-floors. It is especially recommended for use on non-porous sub-floors.
Surface
Preparation:
Use on grade, above grade, or below grade. IFA EP-2000 may be used over structurally sound surfaces of
plywood (sealed), hardboard, concrete, and terrazzo. Use a high quality latex/Portland cement-type patching
compound to fill or level any irregular areas. The floor must be sound, dry, and free from dirt, dust, old
adhesives, grease, wax, or other foreign matter. Concrete floors must be fully cured, free from dust, moisture,
excessive alkalinity, curing agents, and excessive moisture vapor emissions (3 lbs. /1,000 SF/24 hrs.). On- and
below-grade concrete must have a satisfactory moisture barrier beneath the slab.
Application:
The adhesive, tile, and room should be maintained at a minimum temperature of 68-72 degrees F. for
48 hours prior to, during, and after installation. A unit of IFA EP-2000 consists of two (2) parts
labeled Part A and Part B. After opening each container use a can opener to cut the rims off both
containers. Thoroughly mix Part A and Part B separately. Combine the two (2) parts making sure
that ALL of the contents of one can is added to ALL the contents of the second can. Mix the two
parts together thoroughly until they are a uniform color. Immediately after mixing the two parts
together, pour the contents into an open, flat pan or on the floor (epoxy adhesive cures by chemical
reaction; the heat generated by that process reduces the open time and curing is accelerated if left in
the can). Spread the adhesive using a 1/16” x 1/16” x 1/16” square notched trowel. After spreading
the adhesive lay the tile into it immediately. Check open time periodically by lifting a section just laid
to be certain there is transfer of adhesive to the back of the floor covering. The open time will vary
with the temperature, humidity, and porosity of the sub-floor*. Use a kneeling board or work off of
the tile whenever possible. After installation roll the floor using a 150 lb. sectional roller, first in one
direction and then in a direction at a right angle to the first line of direction. THE FLOOR MUST BE
ROLLED BEFORE THE ADHESIVE HARDENS. Prohibit all traffic for 24 hours after installation to
allow adhesive to dry completely.
Limitations:
Clean-up:
Store indoors only. Protect from freezing. Full cure takes 48-72 hours; the finished installation must
be protected from moisture and/or freezing for a minimum of 24 hours. Avoid traffic over the
finished floor for at least 12 hours after installation.
Epoxy adhesives cannot be removed after they set. It is recommended the installer have a bucket
of water and a clean cloth close by in order to remove any wet adhesive immediately that may get
onto the tile.
Coverage:
Approximately 125 square feet per gallon unit. Varies due to sub-floor porosity and irregularities.
Product
Specification:
Base: Part A-Resin; Part B-Hardener
Consistency: Soft Paste
Color: Off-White (Combined)
Weight/Gal: 12.5 lbs. (Combined)
VOCs: Less than 30 grams per liter
Shelf Life:
One Year, Unopened
Open Time: *35-45 Minutes
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
CHEMICAL AND STAIN RESISTANCE
This test was conducted in accordance with ASTM F 925, Resistance to Chemicals of Resilient Sheet Flooring.
By this test, a specified reagent is applied to the surface of the flooring material and allowed to remain in contact
for 60 =/- 1 minute. After the exposure of time, the reagent is cleaned from the surface using warm water and
the surface dried. Within 5 minutes after removal of the reagent, the material is visually examined and the
exposed area compared to the adjacent unexposed area.
The following categories are rated:
ꢀ
ꢀ
Surface Dulling—indicating that the specimen suffered a loss of gloss
Surface Attack—indicating that the specimen suffered surface damage such as softening, warping,
swelling, blistering, peeling, raised, or rough area
ꢀ
Color Change—indicating that the specimen suffered discoloring or bleaching or both.
Each category is rated as No Change=NC, Slight Change=SC, Moderate Change=MC, or Sever
Change=SC. After 24 hours, the exposed specimens are re-examined and similarly rated.
Chemical
Five Minutes
24 Hours
Surface Surface
Dulling Attack Change
Color
Surface Surface
Dulling Attack
Color
Change
5% Acetic Acid
NC
NC
NC
NC
NC
NC
70% Isopropyl Alcohol
Mineral Oil
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
5% Sodium Hydroxide
5% Hydrochloric Acid
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
5% Ammonium
Hydroxide
5.25% Sodium Hypo
chlorite
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
5% Phenol
Unleaded Gasoline
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT WARRANTY
Including 20-Year Limited Wear Warranty
International Floors of America, Inc. warrants that its first line quality flooring material is free
from manufacturing defects (workmanship and/or material) and will replace defective floor
covering for a period of up to one (1) year from the date of purchase in accordance with the
conditions set forth below. If a manufacturing defect is found, the distributor or IFA
representative who sold you the flooring material should be notified promptly of the defect and
supplied with proof of purchase and the amount of flooring purchased.
Inspection by an authorized IFA representative may be necessary to verify that a manufacturing defect exists, or
you may be required to submit samples to the technical laboratory for analysis. IFA will repair defective areas
or will supply at no charge, new IFA materials of the same or similar color, design, and grade for the defective
areas for a period of up to one (1) year from the date of purchase.
If replacement is required in accordance with this warranty and the defective material or pattern has been
discontinued or unavailable, IFA reserves the right to select and supply similar IFA replacement material;
otherwise the same material will be supplied for replacement purposes.
Dimensional stability of IFA flooring material is only guaranteed when IFA recommended adhesive is used.
Limited Term Warranty: 20 years. IFA guarantees its product will not wear out for 20 years.
THIS WARRANTY DOES NOT INCLUDE THE FOLLOWING:
1.
Dissatisfaction due to improper installation, maintenance, or irregularities caused by the
subfloor.
2.
3.
Reduction of gloss due to use.
Discoloration due to improper maintenance practices, tar/asphalt tracking, water with high
mineral and iron content, grease and oil build up from cooking, carpets or mats with rubber
backing, dye transfer from rugs or carpets, or ground in dirt.
4.
5.
Damage due to stains, burns, cuts, gouges, scuffs, scratches, indentations, improper use of
furniture/floor protectors and other accidents or abuse.
Problems or damage due to moisture (including fungus discoloration), alkali or hydrostatic
pressure in the subfloor.
6.
7.
8.
Color variations from samples or printed illustrations compared to the actual production runs.
Installation of flooring over particle boards, chipwood, or pressboard.
Installations where material was not installed with the recommended IFA adhesive in
accordance with IFA’s specifications and recommended usage.
9.
Installation of IFA’s flooring products on grade or below grade concrete subfloors at sea level
or below sea level areas with an adhesive other than IFA’s recommendation.
Installation of IFA tile over existing tile, sheet vinyl or old existing concrete conditions.
10.
This warranty is made solely to the original purchaser of IFA first quality flooring material and is not transferable
under any circumstances. This warranty is in lieu of any other expressed warranty. No representative,
employee, or agent of IFA Inc. or any other person is authorized to assume for IFA any additional liability or
responsibility in connection with IFA’s floor covering except as described above. Implied warranties or
merchantability and fitness for a particular purpose are limited to a period of one (1) year from the date of
purchase. In no event shall IFA be liable for indirect, consequential or incidental damages of any kind.
Claims under this limited warranty must be made in written form and addressed to the following:
International Floors of America, Inc.
1701 Mars Hill Road
Florence, AL 35630
International Floors of America, Inc. reserves the right to update the standard procedures and specifications at any time.
For commercial and residential maintenance instructions, please refer to the current maintenance program sheets.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
by
International Floors of America, Inc.
Headquarters & Factory
1701 Mars Hill Road
Florence, AL 35630
Ph: 256-767-4990
Fax: 256-760-1763
Tech.man.102002
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
|