Intellinet Network Solutions Home Security System 550703 User Manual

Wireless Network

IP Camera

PROFESSIONAL SERIES

Model 550703

User’s Guide LV2.0

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Important Notice

1. Camera surveillance laws may differ for each country. Please contact the local authorities to avoid any

surveillance law violations.

2. Please note that the CMOS lens that comes with the Wireless Network IP Camera can be damaged

permanently if the camera lens is exposed to direct sunlight. If your application demands prolonged

exposure to sunlight, you should consider equipping it with a sun visor.

3. The Wireless Network IP Camera is not weatherproof. Please be aware of environmental specifications

included in the manual. For outdoor use, please use a weatherproof case to protect the Wireless Network

IP Camera from water, moisture, or temperature (higher or lower than specification). For Wireless

Network IP Camera cleaning, gently wipe with clean dry cloth.

4. Be sure to use only the DC adapter that is provided with your camera. Connecting the Wireless Network

IP Camera directly to AC current may cause electric damages to the Camera.

5. Be cautious when handling Wireless Network IP Camera. Physical shocks may cause serious damage.

6. Be sure to mount the Wireless Network IP Camera securely to avoid any human injures. Please keep the

Wireless Network IP Camera out of reach of children.

7. If the Wireless Network IP Camera does not operate properly, please contact the closest local Wireless

Network IP Camera distributor for after sales service. In all cases, you are prohibited from

disassembling the product. If you do, INTELLINET ACTIVE NETWORKING is not responsible for

any malfunction or the service warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

TABLE OF CONTENTS

PRODUCT OVERVIEW

IP N

BOUT WIRELESS

ETWORK AMERA

AIN FEATURES AND BENEFITS

YSTEM REQUIREMENTS

PHYSICALDESCRIPTION

ONTENTS

OP VIEW AND DESCRIPTION

EAR VIEW AND DESCRIPTION

INSTALLATION SUMMARY

ASSIGNING IPADDRESS & ACCESSING NETWORK IP

CAMERA HOME PAGE

IP A

SSIGNING

DDRESS

DDRESS BY USING

INSTALLER

IP C

ONNECTING IRELESS ETWORK

AMERA TO A

IP I

SING

NSTALLER

IP A

SSIGNING

DDRESS BY USING YPER ERMINAL

ONFIGURING YPER ERMINAL

IPA

DDRESS

SSIGNING AN

IP C

CCESSING THE IRELESS ETWORK

AMERA OME AGE

TARTING THE EB ROWSER

OGIN AGE

IP C

ETWORK

AMERA OME AGE

ADJUSTING THE CAMERALENS

DJUSTING THE OCUS

EPLACING THE ENS

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

CONFIGURINGADMINISTRATION TOOLS

DMINISTRATOR ENU VERVIEW

MAGE ONFIGURATION

ETWORK ONFIGURATION

IRELESS ONFIGURATION

SER ONFIGURATION

VENT RIGGER ONFIGURATION

IME ONFIGURATION

YSTEM ONFIGURATION

APPENDIX

A. T

ECHNICAL PECIFICATIONS

B. FAQ

C. T

ROUBLE HOOTING

. U

IP A

TILIZING

DDRESSES ON OCAL ETWORK

NTRODUCTION

IP C

ONSTRUCTION AND ETWORK LASS

C C

LASS ETWORK

E. U

PDATING IRMWARE

DENTIFY THE VERSION OF FIRMWARE

OWNLOAD EW IRMWARE

NSTALL EW IRMWARE

F. T I/O C

ONNECTOR

G. RS 232 CABLE

H. D

YNAMIC OMAIN AME ERVER

. H -S

IGH PEED OLUTIONS

. R

EINSTATING THE ACTORY EFAULT ETTINGS

K. G

LOSSARY OF ERMS

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

PRODUCT OVERVIEW

About the Wireless Network IP Camera

The Wireless Network IP Camera can be connected directly to Ethernet or Fast Ethernet networks

and also supports wireless transmission based on the IEEE 802.11b standard. It is different from the

conventional PC Web Camera; the Wireless Network IP Camera is as standalone system with built-

in CPU and web-based solutions providing a low cost product that can transmit high quality video

images for monitoring. The wireless Network IP Camera can be managed remotely, accessed and

controlled by any PC/Notebook over an intranet or the Internet via a web browser. The simple

installation procedures and web-based interface allows easy integration into your network

application environments coupled with many applications such as remote monitoring for a cost-

effective solution.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Main Features and Benefits

Convenient Operation

The Wireless Network IP Camera is a standalone system with built-in CPU requiring no special

hardware or software such as PC frame grabber cards. The Wireless Network IP Camera supports

both Active-X mode for Internet Explorer and JAVA mode for Internet Explorer and Netscape

Navigator. Therefore, all that is required is a common web browser, such as Microsoft Internet

Explorer 4.x or above.

Open Standards

The Wireless Network IP Camera supports TCP/IP networking, SMTP e-mail, HTTP and other

Internet-related protocols. It can be used in a mixed operating system environment with Windows,

Unix, Mac and OS/2. It integrates easily into other web/intranet applications and CGI scripts.

Wired and Wireless Network Support

The Wireless Network IP Camera supports both wired and wireless transmission providing the

advantage of mobility, flexibility and high-speed wireless LAN based technology (IEEE 802.11b) to

transform it into a total solution for your network. Three modes can be configured from the slide on

the rear panel:

●

Local Area Network (Ethernet / Fast Ethernet) only

Local Area Network (Ethernet / Fast Ethernet) and Wireless Local Area Network (802.11b)

Wireless Local Area Network (802.11b) only

Simple Administration

Using a standard web browser, you can configure and manage the Wireless Network IP Camera

directly from its own embedded web pages. The embedded operating system is upgradeable through

the network.

Firmware Upgrades are available on the web at: http://www.intellinet-network.com/ipcamera/

External Devices

The auxiliary input/output connector on the camera allows you to connect your Wireless Network IP

Camera to a variety of external devices; such as IR-sensors, switches, and alarm relays.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Security

Your Wireless Network IP Camera includes a self-contained web server, which means that digital

images can be secured in the same manner as with any other Internet host. Your Network

Administrator, using the unit’s security settings in combination with an organization’s Internet

firewall, normally implements data protection. The Administrator can decide whether individuals,

groups, or the whole world may access the camera. The Wireless Network IP Camera supports

multi-user password protection

Compression and Performance

With an adaptive frame rate dependent on the image and lighting conditions, the Wireless Network

IP Camera delivers up to 30 JPEG images per second at a resolution of 320x240.

Broad Range of Applications

With today’s high-speed Internet services, the Wireless Network IP Camera can provide the ideal

solution for live video images over the intranet and Internet for remote monitoring. The Wireless

Network IP Camera allows remote access from a web browser for live image viewing and allows

Administrator to manage and control the Wireless Network IP Camera anywhere and any time.

Apply the Wireless Network IP Camera to monitor various objects and places such as homes,,

offices, banks, hospitals, child-care centers, amusement parks and other industrial and public

facilities. The Wireless Network IP Camera can also be used for intruder detection, to capture still

images for archiving and many more applications.

Free Application Software *

IP Installer – for quick installation

Multi-Viewer – for viewing of 4 cameras simultaneously

PDA Viewer – for viewing the camera on Windows CE PDA devices.

* Available at http://www.intellinet-network.com/ipcamera/.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

System Requirements

Network

10Base-T Ethernet or 100Base TX Fast Ethernet

Wireless Local Area Network

IEEE 802.11b Wireless LAN

Recommended PC or Notebook to Access the Wireless Network IP Camera.

System Requirements:

CPU: Pentium II, 266 MHz or above

Memory Size: 32 MB (64MB recommended)

VGA card resolution: 800 x 600 or above

Web Browser:

Internet Explore 5.0 or above (Active-X & JAVA Mode-Image View for Windows OS and JAVA

Mode – Image View for other OS)

Netscape 6.0 or above (JAVA Mode – Image View)

Multi-View Applications:

Supports OS: Win 98, Win 98 SE, Win 2000, Win Me, Win XP

System requirements for Multi-View:

CPU: Pentium III, 450 MHz or above

Memory Size: 128 MB (256 MB Recommended)

VGA card resolution: 800x600 or above

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

PHYSICAL DESCRIPTION

Contents

Carefully remove all items from the package. In addition to this User’s Guide, be certain

that you have:

‹ One Wireless Network IP Camera (550703)

‹ Two External Wireless Antennas

‹ One Installation CD-ROM

‹ One Quick Installation Guide

‹ One Printed Manual

‹ One AC Power Adapter (suitable for your country’s electric power)

‹ One Camera Stand

* If any item is missing, or if you find any damage or mismatch, promptly contact

your dealer for assistance.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Top view and Description

Network Activity LED

Image Capture LED

Operating status LED

Image Capture LED (red): The Image Capture LED flashes when users are accessing the camera,.

It flashes once when an image is being captured or saved.

Operating Status LED (green): This LED indicates the Wireless Network IP Camera’s operating

status. Once power is supplied, the LED stays on for the first 15-20 seconds, and then it blinks once

every second as long as the power is connected properly.

Network Activity LED (green): This LED indicates network activity.

NOTE

1. After connecting the Ethernet network, the status led (green) on the right side of the

camera should be on. If not, check your network connection.

2. The slide switch on the rear panel must be positioned to LAN/WAN or WLAN setting for

the wireless communication to take effect.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Rear View and Description

Antenna Connector

RS 232 Connector

Network Connector

GPIO Connector

Power Connector

LAN/ WLAN-LAN/ WAN

Power Connector: Only use the AC adapter provided by your dealer to avoid any possible damage

from electric shock.

Network Connector: For connection of 10baseT Ethernet or 100base TX Fast Ethernet cable.

GPIO Connector: For connection of external devices such as infrared sensors, alarms, or motion

detectors (please refer to Appendix F – The I/O Connector).

RS232 Cable Connector: For connection of external devices such as an external pan/tilt/zoom

mechanism, or direct connection to a serial port for configuration (please refer to Appendix G - RS

232 Cable).

IMPORTANT

1. After connecting the Ethernet network, the status led (green) on the right side of the camera

should be on. If not, check your network connection.

2. Connect Wireless Network IP Camera to Ethernet network. The default position of the camera’s

network switch is in the center position, meaning the camera operates in both LAN and WLAN

modes.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

INSTALLATION SUMMARY

1. Connect Ethernet and power to the Wireless Network IP Camera.

2. Install and launch the “IP-Installer”

3. Assign an IP address and network settings

4. Securely mount the Wireless Network IP Camera.

5. Adjust the Focus

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

ASSIGNING IP ADDRESS & ACCESSING THE WIRELESS

NETWORK IP CAMERA HOME PAGE

Assigning an IP Address

To access the Wireless Network IP Camera, you need to assign an appropriate network IP address.

IMPORTANT

• Please use the newly assigned IP address, do NOT use any occupied IP address, the default, or the

example IP address.

• It is highly recommended that you assign an IP address before placing the Wireless Network IP

Camera in a remote location or network.

• Network IPAddress:

A network IP address is an identification code for computers or devices on a TCP/IP network.

Networks using TCP/IP protocol route messages based on the IP address of the destinations within

a closed Network. IP addresses can be assigned at random as long as each one is unique. However,

connecting a private network to the Internet requires using registered, public IP address to avoid

duplicates. IP address can be acquired from a network administrator or an Internet service provider.

• MAC (Media Access Control) Address (Ethernet)

MAC address is a hardware identification code that uniquely identifies each device of a network.

The MAC layer interfaces directly with the network media. Consequently, each type of network

media requires a different MAC layer. The MAC address of Wireless Network IP Camera is a 12-

digit number. A unique MAC address can be found on the label on the bottom of each Network IP

Camera.

NOTE

Please run the IP address installation program (IP Installer.exe) on a PC that is connected to the

same local network as the Wireless Network IP Camera.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Assigning an IP Address Using IP Installer (recommended)

Connecting the Wireless Network IP Camera to a PC

1. Connecting with direct cable (Non Crossover UTP cable). Used when connecting the Wireless

Network IP Camera to a switch, hub or router.

Connect

the

Wireless

Network IP Camera to a PC

through a HUB

2. Connecting with Crossover UTP Cable. Use the crossover cable to directly connect the

Wireless Network IP Camera to a PC.

Connect

the

Wireless

Network IP Camera directly

to a PC through LAN ports.

Crossover Cable

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Using IP Installer

To install an IP address, you should use the IP Installer provided with Wireless Network IP Camera.

You can also download the latest version of this program from the web site (http://intellinet-

network.com).

Note : System requirements for IP Installer: Microsoft Windows9x/NT/2000/XP.

① Execute the IP Installer after the Network

IP Camera has completed the boot process

(wait at least 15 seconds).

② When the IP Installer is executed, the panel

shows every Wireless Network IP Camera

connected on the local network.

③ From the Wireless Network IP Cameras

listed, select one to assign a new IP address

(every Wireless Network IP Camera has a

factory default IP address).

Note: The MAC Address can be found on the underside label of the Wireless Network IP

Camera. To choose a Wireless Network IP Camera, click on its list.

Enter the Administrator ID and password in the blank (Default Administrator ID and password are

all “admin”) to assign (or change) the IP Address for the Wireless Network IP Camera..

Enter the IP address, Gateway address, Subnet Mask address, and DNS Server address that are

assigned from network administrator. (When the addresses are not assigned properly, you cannot

access the Wireless Network IP Camera).

The Server IP Address represents an IP address of a PC that runs a TFTP Server which is being used

to upgrade the firmware of the Wireless Network IP Camera via Hyperterminal. This upgrade

method is designed for engineers. Therefore, the Server IP Address field can normally be left blank.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

After entering all addresses for the Wireless Network IP Camera, click the “Change Network

Configurations” button.

The following message is displayed once all the information is set up properly. Click OK.

NOTE

After changing the Network Configuration, it will take about 15 seconds to reboot the Wireless

Network IP Camera.. After that you may access the Wireless Network IP Camera Home Page.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Assigning IPAddress by using Hyper Terminal (Advanced Users only)

You can assign an IP address by using Hyper Terminal. In this case, you should configure Hyper

Terminal first

Configuring Hyper Terminal

Hyper Terminal is a basic program for Windows 9x/NT/2000 and XP. A PC can communicate with

external devices through the serial port by using this program. The steps you should take to set the

Hyper Terminal are as follows in the case of Windows 2000 OS:

① Start Æ Programs Æ Accessories Æ

Communications Æ Hyper Terminal.

Select one of the icons and then enter an

appropriate name in the box.

② Select a serial port of PC, then click the

“OK” button. (Usually COM1 or COM2 is

recommended).

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

③ Configure bit/sec as 19,200 and leave the

other settings at the default values.

④ The panel looks like this image when

configured properly. (If it does not, repeat

steps 1-4.)

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Assigning IPAddress

Follow these steps to assign an IP address using Hyper Terminal

1. Execute “Hyper Terminal” on your PC

2. Connect an RS232 Cable to the serial port of the PC that you have selected in Chapter 4.3.1 -

Configuring Hyper Terminal and the Wireless Network IP Camera serial port while Hyper

Terminal is executed.

3. Supply power to the Wireless Network IP Camera.

4. A count down will start with the message “Press any key to stop auto-boot.”

5. Press any key. “Boot” prompt should appear as below.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

6. You can see Network Configuration while [Boot] prompt is running by pressing ‘p’ key again.

Here, inet on ethernet (e), host inet (h) and gateway inet (g) values are network configuration values.

You should change these values in most cases. If you don’t know what values you should assign,

contact the network administrator.

Inet on ethernet (e) is the IP address and Subnet Mask address of the Wireless Network IP Camera.

IP address and Subnet Mask addresses are separated by colon (:). For example, IP address is

represented by decimal numbers delimited by dots (.), e.g., ‘192.168.1.27’. Hexadecimal numbers,

e.g., ‘ffffff00’ in the case of ‘255.255.255.0,’ represent the Subnet Mask address. Note that the

numbers in the Subnet Mask value are not delimited by dots. See the example in the above picture.

Host inet (h) is the address to which Wireless Network IP Camera tries to connect to upgrade its

firmware program in flash memory. The Wireless Network IP Camera first searches for this host on

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

the network on booting sequence. For more information on Wireless Network IP Camera upgrade,

refer to “E. Updating Wireless Network IP Camera’s Newly Upgraded Program”.

Gateway inet (g) is the gateway address of the Network Camera

7. Type ‘c’ to change the network configuration in [Boot] prompt. If you type ‘c’,, the Wireless

Network IP Camera shows you the information you can change and the current assigned values.

You can change as the following figure.

8. When you terminate the Hyper-Terminal program after changing the network configuration,

Hyper-Terminal asks you whether to save the session. If you save the session, you can re-use

the hyper-terminal. To re-use the session you saved, click Start --> Programs --> Accessories --

> Communications --> HyperTerminal --> Wireless Network IP Camera.. ht in the case of

Windows 2000.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Accessing the Wireless Network IP Camera Home Page

After assigning the Wireless Network IP Camera an IP address, you may access Wireless Network IP

Camera and monitor real-time images on the Internet. You may configure Wireless Network IP

Camera within its own pages through any standard Web browser on a local or remote network.

Starting Web Browser

Start your web browser and enter your Wireless Network IP Camera’s IP address.

Default IPAddress

http://192.168.1.221/

Please note: 192.168.1.221 is the default IP Address of Network IP Camera. If you have change the IP address

using IPINSTALLER.EXE (see above), you need to enter the new IP Address in your web browser.

This page is to enter the Wireless Network IP Camera’s built-in Home page. To access this page, you

may be prompted to enter a user ID and password.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

1. ID and Password

If you key in a user ID and password, you can access the camera to monitor real-time video.

With Administrator’s ID and password, you can access real-time video with Administrative authority.

The default value of both user ID and password are “admin” and the administrator may change it at

the Administrator Menu. Each ID and password must be composed of no more than 10 bytes (e.g.,

10 English letters). For guest users, the Wireless Network IP Camera has default ID and password

“guest”, but guests cannot access the administrator tools..

2. Behind Firewall

If your PC is connected on a network with a firewall, you may not view real time video properly

because the video TCP port is blocked. If you are behind a firewall, you may view real-time video

through the Wireless Network IP Camera’s Server Push Viewer that transmits video through the

web’s TCP port instead of the video TCP port. By clicking on the “Behind Firewall” menu, you may

directly connect to the Server Push Viewer when you access the Wireless Network IP Camera home

page.

3. Active-X for MS Explorer Users

For all Microsoft Explorer users, the Active-

X Control program is required. The program

will be installed automatically when a user

accesses the Wireless Network IP Camera.

For Active-X installation on your PC, just

click ‘Yes’ to the question “Do you want to

install the program?” on the pop-up window.

If you cannot see images after installation,

you should download and install Active-X

manually.

The Active-X Installer may not show up, if the Security Settings on your PC are set too high. You

need to allow the execution of Active-X scripts.

The Active-X Installer requires the user currently logged on to the system to have system

administrator rights (Windows 2000 and Windows XP).

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

The manual installation requires the user to have system administrator rights (Windows 2000 and

Windows XP).

Active-X Manual Installation

If the Active-X program fails to install automatically, you may install it manually.

The manual installation program can be downloaded as follows:

Active-XVisit http://www.intellinet-network.com/driver/NetCam.exe to download and install Active-

X manually as follows:

① When the panel appears, select

"Run this …" if you want to

install right away.

② Install Shield Wizard appears after

finishing download.

③ Check “Repair” then click “Next”

④ When installation is completed,

press “Finish”

⑤ Go back to the Login page to access

Camera homepage.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

4) Java Applet for Windows, Macintosh or Unix System user.

Java Applet viewer is for a user who accesses the Wireless Network IP Camera through a computer

that does not Utilize MS Windows Active-X, such as Macintosh computers. Java Applet viewer is

run with Java Virtual Machine that is installed on the user’s computer.

Macintosh and Unix/Linux Systems

The Wireless Network IP Camera Active-X program is based on MS windows OS. Therefore it is

impossible to access the Wireless Network IP Camera and monitor real time images through the

default viewer.

If a user accesses the Wireless Network IP Camera through Macintosh or Unix systems, Wireless

Network IP Camera detects that OS is not MS Windows and it operates the Java based image

viewer to show real-time images. Some functions are not available for Java Applet.

NOTE

It is highly recommended that you select Active-X viewer for Windows 95, 98, 2000 or XP when

using Internet Explore 4.0 or higher. If not, choose Java Applet Viewer.

NOTE

Windows XP does not have the JAVA Virtual Machine installed by default. If you are planning

on using JAVA to access your camera, you may need to install the JAVA VIRTUAL MACHINE

for Windows first. You can download it here:

http://www.java.com/en/download/installed.jsp

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Wireless Network IP Camera Home Page

Having completed the login procedure, you now see the Wireless Network IP Camera home page

1. Connected Client

Shows the number of users currently connected to the camera (100 users can access the camera

simultaneously).

2. Administrator Menu

Provides access to the Administration menu. However, only users who have Administrator authority

can access the menu with the Administrator ID and password (please refer to Configuring the

Administration Menu).

3.Logout

Logs the user off the camera.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

4. SAVE, STOP SAVE, SNAP SHOT, SHOW

ONLY IMAGE

① SAVE, STOP SAVE

Users can save real time images from the

Wireless Network IP Camera.

Press SAVE then select the folder where you want to save images. (The image is saved as an

AVI file.)

Once it starts to save the image, “Saving” message and XviD Status appear.

To stop saving, press STOP SAVE.

(Saving Mode)

(XviD Status)

NOTE

„

You may view the saved image using Window Media Player or Real Player.

Click the “Install XviD” for AVI saving

The AVI saving will generate a new file with a different name in the same folder

every 20 minutes.

(For example) file name 2002_04_22_15_00, file name 2002_04_22_15_20…

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

② SNAP SHOT

To save only one image, press

SNAP SHOT and then select a

folder.

Save the image as JPG file.

③ SHOW ONLY IMAGE

When you want to see only the video

panel, press SHOW ONLY IMAGE.

5. Frame Rate

You may choose image transmission speed. If you choose ‘Fastest”, you will get images at the

fastest frame rate. The transmission speed depends on your network line’s capacity and PC’s

performance. The maximum selectable frame rate depends on the setting for this user in the USER

CONFIGURATION of the Administrator Menu.

6. Expansion

You may select the image size from 0.5 to 2. This function may be used when you want to expand

image size on your PC (resolution cannot be changed).The Expansion function does not change the

true resolution of the image, it is a digital zoom.

The image resolution can be changed in the IMAGE CONFIGURATION (Administrator Menu).

7. Camera Name

You can set a camera name (please refer to Chapter 6.7 - System Configuration)

8. Location

This shows where the camera is located (please refer to Chapter 6.7 - System Configuration).

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

ADJUSTING THE CAMERA LENS

Adjusting the Focus

In order for the Focus Assistant to access the full focusing range for your application environment,

simply turn the lens in the clockwise or counter clockwise direction. Unless you are replacing the

lens, do not unscrew it more than 1.0 mm.

*Adjust the camera focus while reviewing the picture quality on your web browser.

Lens

1.0 mm max

NOTE

◆ A Good level of focus is normally achievable throughout several planes within the camera’s

focusing spectrum.

◆ Since optimum focusing is dependent upon the camera’s field of view, it is important to scan

the focusing plane from the closest to furthest perspectives before attempting any fine-tuning.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Replacing the Lens

Because the Wireless Network IP Camera is designed with a CS-Mount, the lens supplied with

your product can be replaced with any standard C or CS lens typically used within the

surveillance industry.

Follow the instructions below to replace the supplied lens with any C or CS type lens:

1. Unscrew the Wireless Network IP Camera lens by turning the lens counter-clockwise

2. C-lens only: Attach the new lens to a C-CS adapter

3. Screw the new lens onto the Wireless Network IP Camera. If applicable, adjust the iris

according to the prevailing light conditions.

4. Refer to Adjusting the Focus on page 29.

5. Reload your Web browser and monitor the results from the product Home Page.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

CONFIGURING ADMINISTRATION TOOLS

You can control the configurations of the Wireless Network IP Camera by Administration Tools.

Only authorized users can access administration tools. Non-authorized users attempting access will

see the message: “You are not an administrator”.

Press Administrator Menu to control all configurations for Wireless Network IP Camera.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Administrator Menu Overview

The table below provides a one-step overview of the Administration Tools:

Image Configuration

Network Configuration

Wireless Configuration

User Configuration

Event Trigger Configuration

Time Configuration

System Configuration

Home

To configure compression rate, image size, brightness, contrast, etc.

To configure camera IP, web server port, image transfer port

To configure wireless setting

To configure user ID & password

To configure event trigger condition, image capture option, trigger

output

To configure date and time

To configure the camera name, location, PTZ and see the system

information.

Go to Wireless Network IP Camera home page

To prevent any unauthorized use, Wireless Network IP Camera access is restricted to defined users.

The Administrator(s) has exclusive access to the product administration tools and can determine the

registration, and access rights for all users.

Enter the default ID and password, then click “SUBMIT”

(Default ID and password are all “admin”)

CAUTION

Although, the Administrator’s default username and password (set to “admin” for all)

can be used for logging onto the unit for the first time, it is highly recommended that you change

this password for your Wireless Network IP Camera as soon as possible – since all Wireless

Network IP Camera products are shipped with the same default ID and password.

NOTE

Make sure to click “submit” after changing configuration or your changes will not be saved.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Image Configuration

Example of Wireless Network IP Camera definable image attributes using the Focus Assistant:

1. Compression rate

The file size of a JPEG-compressed image depends upon the actual content of the image. Images

containing much detail will generate larger files. Image quality is controlled through the level of

compression; where, high compression yields small files, while low compression maintains higher

image quality at the expense of larger files. The table below contains compression ratios for each

step, derived from real-life tests:

Compression Rate Level 1

Level 2

Level 3

Level 4

Level 5

QVGA

VGA

Level 6

Level 7

Level 8

Level 9

Level 10

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

2. Image Size

You may choose the image size VGA(640x480) or QVGA(320x240) and 160*120

Large image sizes (VGA) yield lower frame rates, while small sizes maintain higher frame rates

3. Vertical Flip

Turns the image view upside down (affects only the web browser live view)

4. Horizontal Flip

Switches the image view right from left (affects only the web browser live view)

5. Display Time/Date Stamp

Turns on/off the time and date stamp in the live image (affects only the web browser live view)

6. Brightness Mode, Brightness

The higher the number, the brighter the image. (Input digits from 0 to 255)

7. Contrast

The higher the number, the clearer the contrast. (Input digits from 0 to 15)

8. Hue

The lower the number, the pinker the color. The higher the number, the greener the color.

(It is possible to input digits from 0 to 15)

9. Saturation

The higher the number, the deeper the color. (It is possible to input digits from 0 to 255)

10. Sharpness

The higher the number, the more vivid the color. (It is possible to input digits from 0 to 7)

11. Exposure Mode

You may select “Auto” and “Manual”

12. Exposure

The higher the number, the brighter the image.(It is possible to input digits from 0 to 255)

13. Back Light

When the light is not sufficient, “Back Light” may increase visibility.

14. Further Reduce Exposure Time

Reduces exposure time from 1/20 to 1/100 under heavy light.

15. Indoor/Outdoor

Controls the brightness under the circumstance

16. Light Frequency

Sets a frequency for the image sensor

16. Submit

Transfers current configuration data to a Wireless Network IP Camera (after transferring data)

17. Cancel

18. Load Default Values

Sets the configuration as default values. (No need to press SUBMIT)

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Network Configuration

This screen defines the network type and addresses of the Wireless Network IP Camera. Here you

can configure the Camera’s IP address, the DNS server address, and the Server IP address. Each

configuration takes just a few seconds for booting after pressing SUBMIT.

1. Set IPAddress, Subnet Mask, and Gateway Address.

To set the IP Address, Subnet Mask, and Gateway Address manually, you may select “manually” in

combo box.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Manual configuration can be done using the IP installer or the information on this page.

(If you have trouble configuring network system information, please ask your Network

Administrator for assistance.)

To set DHCP, you may select ‘using DHCP’.

When selecting “using DHCP”, the IP Address, Subnet Mask Address and Gateway Address may not

be activated. Under DHCP selection, the IP address may be sent to an e-mail address whenever IP

address is changed. Users in a local area network may check the IP address through IP installer.

NOTE

If you select “DHCP”, you may see the rebooting message “Now the Network Camera

is rebooting to apply the changes...” on the Web Browser. After completing

rebooting, the Operating Status LED blinks once per second to verify that the changes were

applied.

To select DHCP, you must have DHCP server in the network. Otherwise, the IP address will

reboot automatically as the previous IP address. It may take 4 minutes for booting.

After rebooting, please reenter the previous IP address.

You may see the fail message from the Network Configuration page.

2. Send IPAddress to E-mail

To send camera system information (Camera Name, Camera Location, DHCP IP address), check

the text box and enter you e-mail address. (You should configure your SMTP server information

first)

3. Server Port Number

Set the Port Number for the web server. (The default port number is ‘80’ and users can select from

80 to 1023)

4. Image Transfer Port Number

Set the port number for the image transfer. (The default port number is “8080” and users can select

from 8000 to 65535)

5. Ugrade Port Number

Set the Port Number for upgrading firmware. (The default port number is “9000” and users can

select from 8000~65535)

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

6. PTZ port number (not useable in Wireless Camera)

CAUTION

Be careful not to use the same port number for Image Transfer Port Number and Upgrade port

number. If it is duplicated, a warning message will appear.

7. ETSP port number

Set the port number for ETSP [Event Trigger Setting Program]. (Default is “11000” and users can

select from 8000 to 65535. For the detail of ETSP, please refer to the ETSP manual.)

8. 1st, 2nd DNS Server Address

To map between IP address and domain name, you should enter you DNS server address.

If a user set the DNS server into the camera, users can configure the SMTP server, FTP server, and

NTP server with domain names.

DNS (Domain Name System)

DNS (Domain Name System) is used to map between IP address and domain name. Every network

device connected to the Internet has an IP address that is used instead of its domain name.

Common users are not familiar with IP addresses but the domain names.

If a user accesses a certain network device with its domain name, a DNS server translates the

domain name into an IP address .

9. SMTP server

You need to specify your SMTP Server if you want to use any of the camera's email features. Other

than that, it can be left blank.

10. Use SMTPAuthentication

If you need user authentication for accessing the SMTP server, check this box. and enter your ID and

password for your SMTP server. Realm should be left blank, and authentication should be set to

- Authentication method: Choose the SMTP authentication method.

- ID: : Enter the user ID for SMTP authentication.

- Password: Enter the user password for SMTP authentication..

- Realm: : Enter the Realm for SMTP authentication.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

11. DDNS Registration

To register the Wireless Network IP Camera to a DDNS (Dynamic Domain Name Server), check the

Enable box. A dynamic IP address complicates remote access since you may not know what your

current WAN IP address is when you want to access your network over the Internet. The solution to

the dynamic IP address problem comes in the form of a dynamic DNS service. (Please refer to the

Appendix for details.)

12. ID, Password

Enter the ID and password to find the registered Wireless Network IP Camera in the DDNS server.

13. Host Name

Enter the host name to find the registered Wireless Network IP Camera in the DDNS server.

14. DDNS Manual Update

You can update the DDNS manually.

15. Status

Shows the status of successful DDNS access.

16. Submit

Sends configured data to the Wireless Network IP Camera.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Wireless Configuration

This screen is used to configure wireless settings to match your access pointer for a wireless network

connection.

Wireless Setup

1. Use the Connection Mode to determine the type of wireless communication for the Wireless

Network IP Camera. There are two choices: Infrastructure Mode and Ad-hoc Mode. The default

setting for the Connection Mode is Infrastructure Mode.

2. Set the Service Area Name (SSID) as per the access point setting to which the user wants to

connect.

3. The channel is set to channel 1 as a default. In Infrastructure Mode the camera will automatically

find the Access Point. The channel only needs to be set in Ad-hoc mode.

4. The default setting for the “Tx rate” is Auto; however, it can be set to 5.5. or 11 mbps if required.

NOTE

Keep in mind the slide switch on the rear panel must be positioned to LAN-WAN or WLAN for the

wireless communication to take effect.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Security Settings:

Wireless network communications are easily intercepted. WEP (Wired Equivalent Privacy) is an

encryption method specified by the IEEE 802.11b standard to make any intercepted communications

extremely difficult to interpret by unauthorized parties.

The WEP key needs to be entered in HEX code.

To set up 64-bit WEP, input 10 HEX characters, for example, 0123456789.

To setup 128-bit WEP, input 26 HEX characters, for example, 01234567890123456789012345

Example 1) Your access point uses 64-bit encryption, default key 1 and the key value is

0123456789. Your wireless camera WEP setting will be:

64bit

Encryption (WEP):

0123456789

WEP Key Entry #1:

0000000000

WEP Key Entry #2:

0000000000

WEP Key Entry #3:

0000000000

WEP Key Entry #4:

Default Key:

Example 2) Your AP uses 128-bit encryption, default key 2 and the key value is

01234567890123456789012345. Your wireless camera WEP setting will be:

128bit

Encryption (WEP):

00000000000000000000000000

WEP Key Entry #1:

01234567890123456789012345

WEP Key Entry #2:

00000000000000000000000000

WEP Key Entry #3:

00000000000000000000000000

WEP Key Entry #4:

Default Key:

Please note:

All four WEP Keys need to be set up the exact same way as they are defined in your Wireless Access

Point.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Make sure the Encryption Code is the same as that of the access point the camera will be connected

to under Infrastructure Mode. Your PC’s encryption code also needs to be set up to match the

camera’s encryption code under either Infrastructure or Adhoc Mode.

The default setting for the Encryption Key is Disable; therefore, to secure the wireless transmission,

be sure to enable the Encryption Key by entering the relevant data.

NOTE

Carefully input the Encryption Code. Any error will cause the communication link to fail

IMPORTANT

Infrastructure Mode:

This is an 802.11 networking framework in which devices communicate with each other by first

going through an access point (AP). In infrastructure mode, wireless devices can communicate

with each other or can communicate with a wired network. When one AP is connected to a wired

network and a set of wireless stations, it is referred to as a Basic Service Set (BSS). An Extended

Service Set (ESS) is a set of two or more BSSs that form a single sub network. Most corporate

wireless LANs operate in Infrastructure Mode because they require access to the wired LAN in

order to use services such as file servers or printers.

Ad-hoc Mode:

This is an 802.11 networking framework in which devices or stations communicate directly with

each other, without the use of an AP. Ad-hoc Mode is also referred to as Peer-to-Peer Mode or an

Independent Basic Service Set (IBSS). Ad-hoc Mode is useful for establishing a network where

wireless infrastructure does not exist or where services are not required.

SSID (service set identifier):

This is a 32-character unique identifier attached to the header of packets sent over a WLAN that

acts as a password when a mobile device tries to connect to the BSS. The SSID differentiates one

WLAN from another, so all access points and all devices attempting to connect to a specific

WLAN must use the same SSID. A device will not be permitted to join the BSS unless it can

provide the unique SSID.

An SSID is also referred to as a network name because essentially it is a name that identifies a

wireless network.

To connect a wireless client such as a Wireless Network IP Camera to a specific AP, the user of

the camera should specify the SSID name in the camera’s wireless IP setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

User Configuration

This screen is used to configure IDs and passwords for an Administrator and up to 5 users.

1. User Account (max. 10 characters)

There is one Administrator account and 5 user accounts. Account names can be changed.

2. Password (max. 10 characters)

If you want to open your Wireless Network IP Camera to everyone, you cannot change default

user ID and password. However, you should change the administrator ID and password to a

unique selection.

3. Frame Rate

Define the maximum frame rate for each user. This feature is useful if you want to reserve

bandwidth for "power users."

4. Access Rights

The Administrator may assign users rights of viewing control. With the default setting, the

administrator has all configuration authority, and the normal user doesn’t have any right except

to access the login page and the camera home page (live video).

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Event Trigger Configuration

This screen is used to designate an e-mail address or FTP server to receive captured images by

setting SMTP or FTP settings. You may connect external devices such as an infrared sensor or alarm

sensor to use with the provided terminal block (please refer to Appendix F – The I/O Connector).

1. Trigger Condition

This is to select option how to send an event signal to theWireless Network IP Camera.

① Activation of digital input port

The Wireless Network IP Camera receives an event signal from an external device such as an

infrared sensor, alarm sensor, etc.. The trigger condition defines the the "active" state of the

IO Port.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

② Motion detection from……

This is to detect motion from camera by S/W data comparison. When you select Motion

Detection, the Wireless Network IP Camera detects a motion triggered by the camera lens.

To detect motion, the camera compares a previous and present image. Motion is detected

when, the camera recognizes a data change. This feature does not work if the image is too

dark. Also, the Motion Detection only works reliably at a maximum image resolution of

320x240.

CAUTION: Do not use the motion detection function for security monitoring of high value

items. When using motion detection for security, the use of an external sensor, such as

infrared, is recommended.

The "from" and "to" values specify the time window in which the motion detection is active..

Example: From 8 to 19 would activate the motion detection between 8 o'clock in the

morning and 7 o'clock in the evening.

③ Periodically…..

The Wireless Network IP Camera itself is to be triggered automatically by a programmable

setting.

④ Motion detection sensitivity

This is to configure the level of motion detection sensitivity. The level is composed of 10

settings from 0 to 9. The higher the setting, the greater the sensitivity.

In case of level 9 for sensitivity, the camera may detect a tiny motion, even light changes.

It is strongly recommended to configure levels 3 - 6 for sensitivity.

2. Image Capture Option

This is to configure image capture before and/or after an event is triggered.

① Before event

You may set the starting time to capture the image before an event is triggered.

(Input limitation is from 0 to 21 seconds.)

② After event

You may set the finishing time to capture the image after an event is triggered.

(Input limitation is from 0 to 21 seconds.)

③ Image capture frame rate

Set the frame rate from 1 to 15 fps when the image is being captured.

④ Image file name

You may designate an image file name to send via e-mail or FTP after an image is captured.

All captured images are saved as JPG files. (Example. “File name 000”.JPG)

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

⑤ Append to the image file name

You may append some information to the Image file name

A. Camera IP address : Example: “file name _192.168.1.19”.JPG

B. Date and time : Example: “file name_20020218150030.”JPG

C. Trigger condition flag

1. If choosing “Activation of digital input port”, “D” may be appended to image file name.

Example: “file name_D.”JPG

In case of choosing “Periodically every…”, “P” is appended to image file name.

Example: “file name_P”.JPG

D. Image sequence number

If you select this option, you may classify the file that has same extend name.

Consecutive numbers are from “000” to “999”

Example: When you designate the file name as “camera” and select “Image sequence

number,”the file name appears “ camera001.JPG, camera002.JPG ….camera999.JPG”

Image capture option limitation

Configuration for image capture option affects memory capacity. If you configure this option to

excess memory size, the Warning message “Not enough memory…” appears.

The total image capture frame rate must be limited 45 fps due to memory size.

(Before event time + After event time) x Image capture frame rate must be less than 45.

For example, if you configure “Before event time” as 3 seconds, “After event time” as 2 seconds

and “image capture frame” as 3 fps, the total image capture frame rate is ( 3 + 2) x 3 = 15 fps.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

3. Trigger Output

This is to configure digital output states and control script. The Wireless Network IP Camera

sends captured images via e-mail or FTP server when connected external sensors detect events.

① External devices signal output

This is to supply voltage to output port when events are triggered. (This option is only

activated when you select “Activation of digital output” option in previous “Trigger

Condition” option.)

② Send alarm to ETSP client

This is to send an alarm to an ETSP client.

If you check the box, the alarm will be sent to the ETSP client when an event is triggered.

ETSP Client is currently under development (as of January 2005). It will be available for

download at the following address: http://www.intellinet-network.com/ipcamera.

③ Send captured image via e-mail

This is to designate a person to receive a captured image via e-mail.

The Wireless Network IP Camera sends a captured image to a designated e-mail address

through an SMTP server.

You may configure the SMTP server and E-mail address. (E-mail address must

be composed within 50 bytes, which are equal to 50 English characters.

④ Send captured image to FTP server

This is to send a captured image from the Wireless Network IP Camera when an event is

triggered.

Enter FTP server IP address, user ID and password and select a directory to save the image.

The FTP Server Address needs to be entered without "FTP://"!

Example for use of the directory field:

Root Folder for FTP User Account which the camera uses: root

Subfolder in which the images should be uploaded: root/images

In that case you need to enter "images" (without leading or trailing /) in the directory field.

FTP RENAME ENABLE:

If the camera uploads an image to your Web Site every xx seconds (refresh) and if you

display this image on your web page, you should always check this box. Otherwise it can

be left unchecked.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Time Configuration

This screen is used to configure date and time.

1. Synchronized with NTP server

The Wireless Network IP Camera automatically configures date and time through the NTP

(Network Time Protocol) server. The NTP Server is based on Greenwich time. Select NTP

server, IP address and Time Zone to set the date and time automatically, then press SUBMIT. It

may not work due to the possible network error; in this case, you can select other NTP server

and IP address or you can set the date and time manually. Once date and time are set,, you don’t

have to reconfigure when connecting to the Wireless Network IP Camera.

The "Update Interval" tells the camera how often to contact the NTP Server to resync the

internal clock. For time critical applications the update interval can be set from 1 minute to

2880 minutes (= 2 days).

Free NTP Servers can be found at: http://www.ntp.org/.

2. Set manually

Enter the date and time manually, then click SUBMIT.

3. Enable Daylight Savings

This is to configure for Daylight Savings Time.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

System Configuration

This screen is used to configure camera name, location and public image access. It also lets you

remotely restart the camera and restore the factory default values.

1. Camera name

This is to configure camera name for the front-page view. Camera name should be limited to 15

bytes, which are equal to 15 English characters.

2. Camera location

This is to configure camera location for the front-page view. Camera location should be limited

to 30 bytes, which are equal to 30 English characters.

3. Supply voltage to output port option

This option is to supply voltage to the Wireless Network IP Camera’s output port.

Just click “supply” to supply voltage to control the PTZ devices.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

4. Direct public access to image via HTTP

The camera supports a method to access the live image directly without logging in to the camera.

The URL is: http://camera_ip/jpg/image.jpg.

If direct public access is enabled, the image can be accessed without entering username and

password. If direct public access is disabled, a valid username and password must be provided.

This feature is important for users who wish to use the camera in 3^rdparty video monitoring

applications as it turns your Network IP Camera into a "JPG Compatible Camera".

5. Image file name (maximum length 10 characters)

Set the image file name for the public access feature.

Example1 – Public Access is enabled: http://192.168.1.221/jpg/image.jpg

Example2 – Public Access is disabled: http://guest:[email protected]/jpg/image.jpg*

* MSIE does not support this type of command any longer due to a recent security upgrade by

Microsoft.

6. System information

This is to check system information for Wireless Network IP Camera. You may see the model

name, serial no., Mac address of Ethernet and WLAN Adapter, Bootrom & Firmware version.

(Please refer to Appendix E,. Updating Firmware.).

7. Reboot

This function allows you to reboot the camera via your web browser.

8. Restore Defaults

This functions allows you to restore the camera's factory default settings via your web browser.

After the function has been performed, all settings are reverted to the original settings (including

the IP Address, which is set to 192.168.1.221).

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

APPENDIX

A. Technical Specifications

Image

Resolutions supported: 640x480, 320x240, 160x120

Standard JPEG Compression – 10 levels of compressions

Frame Rates: Up to 8 fps at 640 x 480 resolution and 30 fps at 320x240 resolution

Network

10baseT Ethernet or 100baseTX Fast Ethernet

Twisted pair category 5 cables, Standard RJ45 connector

IEEE802.11b Wireless Ethernet, 11 Mbps

Two detacheable antennas, connected via RSMA connectors

Supported Protocols: TCP/IP, UDP, PING, ARP, FTP, TFTP, and HTTP

Configuration by IP INSTALLER Windows Application and/or Web-based administration page.

Network Throughput: Up to 7 Mbps

Image Sensor

1/3” CMOS censor

326,688 pixels, 24-bit color, YUV digital output

Automatic exposure/Gain/White balance control

Image enhancement – brightness, contrast, gamma, saturation, sharpness, etc

664x492 pixel array elements

Electronic shutter: 1/30 s ~ 1/15734 s

Auto back light compensation: Automatic back light on or off depending on the lighting condition.

Lens specification

Replaceable standard CS mount lens

Focal length 6.0 mm, Angular field of view 54°, Object distance 0.1m to infinity

Maximum Relative aperture F1.8

C-Mount adapter available

Hardware

32bit RISC Net ARM CPU

ZORAN hardware compression chip

384 Kbytes video frame buffer

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

4M flash memory

SDRAM 8Mbyte

12V Power supply adapter included

Under 6W power consumption

System Requirements

Operating systems: Windows 9x, Windows NT/2000, Linux, Linux, MaOSc, etc.

Internet Explorer 4.0 or higher.

JAVA support for MacOS, Linux and Windows.

I/O Connector

D-sub 9pin RS232 connector

1 Input to trigger the camera on external events.

1 Output of 12 V to signal external devices, max 150 mA

Installation

Assigning IP address via IP INSTALLER program or web-based.

Approvals

EMC: FCC Class B, CE EN55022/1994, EN61000-3-2 & 3: 1995, EN50082-1: 1997

Operating Temperature

0-50’C

Others

Operating Status LED, Power LED, Image Capture LED, Network Packet Transmit LED

EEPROM clear button

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

B. Frequently Asked Question (FAQ)

1. What is a Network IP camera?

A Network IP Camera is a stand-alone device which allows a user to view live, full motion video

from anywhere on a computer network, even over the Internet, using a standard web-browser.

2. Are all Network IP cameras the same?

No, some network cameras have an embedded OS (operating system) as well as an embedded Web

server. To be called a Network IP camera, the only requirement is that the camera connects to the

network, and not a computer - an embedded OS is what separates network cameras.

3. Why Choose a Network IP Camera over a Web Camera?

An IP Camera is a true networking device containing an embedded OS (Operating System), supports

multiple users, and can be viewed using any web browser. It does not require additional hardware to

operate and therefore has the flexibility to be located anywhere with a network connection. A web

cam must be connected to a host computer, supports only one user at a time, and cannot be shared on

a network. Only the host computer can access the web cam.

4. What is the advantage of the embedded OS?

Cameras with an embedded OS communicate directly with the user; the images or video are sent

directly from the camera to the person(s) accessing it. A Network camera without an embedded OS

must rely on a third party server or a separate piece of software, meaning the images/video is sent to

the third party server, then the user accesses the image from the third party server.

5. Do I need a public fixed IP address for each camera?

No, you of course, can have a real, public, static IP address for each camera, however, using just one

static IP address for your router and a virtual server or port forwarding, you can use many cameras

with just one static IP. Please also note that the IP camera must have an adjustable web server port

(you must be able to change the web server port) to use multiple cameras behind a router.

6. Can I use the camera outside?

The Wireless Network IP Camera is designed for indoor use only.

7. What additional software is required?

Networking IP Cameras with an embedded Operating System (OS) should not need any additional

software.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

8. How does the built-in motion detection work?

It very simply compares what it sees now to what it saw in the last frame and based on a sensitivity

you select will trigger an event. The event can be to send an e-mail, to send an Image to a FTP

server, or to send a series of images (before and after the motion is detected) to an e-mail address or

FTP server.-All required software is built into the camera.

9. What is the maximum length Ethernet cable I can use?

The same topology limitations that apply to any 10/100 Ethernet card apply, meaning the maximum

segment length is 100 meters from the switch/hub to the camera

10. What is Power-over-Ethernet (PoE)?

Power-over-Ethernet (PoE), or "Active Ethernet," eliminates the need to run power to devices on a

wired LAN. Using PoE, installers need to run only a single CAT5 Ethernet cable that carries both

power and data to each device. This allows greater flexibility and significantly decreases installation

costs in many cases.

11. Can Network IP Cameras use different lenses?

Advanced Network IP Cameras utilize CS-mount lenses, which can accommodate a variety of

specialized lenses, such as wide-angle, fisheye or telephoto lenses.

12. What image sizes can be viewed from Network IP Cameras?

Advanced Network IP Cameras use multiple pre-set image sizes that typically include 160 x 120,

320 x 240 and 640 x 480 pixel image sizes.

13. Can I view a Network IP Camera from my PDA?

Network IP Cameras can now be viewed on most Windows systems,, including Pocket PC devices,

such as the Compaq iPAQ, HP Jornada, Dell Axim, Casio Cassiopeia and many others.

You can download the PDA Viewer at: http://www.intellinet-network.com/ipcamera.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

C. Trouble Shooting

This appendix provides useful information to help you to resolve any difficulty you might have with

your Wireless Network IP Camera. Fault symptoms, possible causes and remedial actions are

provided within a quick reference table.

PINGing your IP Address

By sending a packet to the specified address and waiting for a reply, the PING (Packet Internet

Groper) can determine whether a specific IP address is accessible; it also provides a particularly

useful method for confirming addressing conflicts with your Wireless Network IP Camera on the

network.

Disconnect your Wireless Network IP Camera,, follow the instructions below in association with

Symptoms, Possible Cause and Remedial Actions, and run the PING utility to troubleshoot TCP/IP

problems on your network.

① Start a DOS window

② Type ping x.x.x.x, where x.x.x.x. is the IP address of the Wireless Network IP Camera

③ The subsequent replies will provide an explanation as to the case of the problem. Replies can

be interpreted as defined in the table below:

PING Reply

Interpretation and recommendation

bytes = 32 time = 2 ms

The IP address is already used and cannot be used again. Your

must obtain a new IP address

Destination host unreachable

Request timed out

Wireless Network IP Camera is not accessible within your

subnet.You must obtain a new IP address

This IP address is not used by anyone and is available for use

with your Wireless Network IP Camera

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Symptoms, Possible Causes and Remedial Actions

Symptoms

Possible causes

Remedial actions

Wireless Network IP

Camera cannot be

accessed from a web

browser

The IP address is

already used by another from the network

devices

1.Disconnect your Wireless Network IP Camera

2. Run the PING utility (as described in PINGing

your IP Address).

The Power LED is not

constantly lit

The IP address is

located within a

different subnet

Run the PING utility (as described in PINGing Your

IP Address), If the utility returns “no response” or

similar, the diagnosis is probably correct – you

should then proceed as follows

In Windows 95/98 or Windows NT, check the IP

address for your Wireless Network IP Camera is

within the same subnet as your workstation:

1.Click “Start”, “Settings”, “Control Panel” and

“Network”.

2.Specify the TCP/IP adapter and click on

“Properties”. In Properties, Click “IP Address”.

3.Check that the first 3 numbers within the IP

address of your Wireless Network IP Camera match

the first 3 of your workstation. If not, your Wireless

Network IP Camera may be on a different subnet

and the IP address cannot be set from this

workstation. You must set the Wireless Network IP

Camera IP address from a workstation on the same

subnet.

Other networking

problems

Try replacing your network cable

Test the network interface of the product by

connecting a local computer to the unit, using a

standard crossover (hub-to-hub) cable.

If the above actions do not resolve the problem, the

Wireless Network IP Camera may be faulty, In this

case, try to localize the problem by connecting the

camera to the serial port of a local computer, using

the supported RS232 cable

Faulty power supply

Verify that you are using a provided power supply

The network LED is off Faulty cabling

1.To verify that the cables are functional, PING the

address of a known existing unit on your network.

2.If the cabling is OK and your network is

reachable, your should receive the reply similar to

this:

. . . bytes = 32 time = 2 ms

The operating status

LED is off

Faulty connection

Verify that the power is connected

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Your Wireless Network Firewall protection

IP Camera works

Check the Internet firewall with your network

administrator.

locally, but not

externally.

Default routers required

Determine whether you need to configure the default

router settings

The Internet site is too

heavily loaded

Configure the Wireless Network IP Camera to

upload your video images to an FTP server or an ISP

Direct exposure to extreme sunlight or halogen light

may cause serious damage to the CMOS sensor.

Reposition your Wireless Network IP Camera into a

A series broad vertical

white lines appear

across the image.

The CMOS sensor

becomes overloaded

when the light is too

bright. This can happen more shaded location immediately.

e.g. with sun light

reflexes.

Note: damage caused to Wireless Network IP

Camera through over exposure to direct sunlight or

halogen light is not covered under the product

warranty.

Bad focus

Focus has not been

correctly adjusted

Adjust the camera manually until the image views

clear.

Noisy images

Video images may be

noisy if you are using

the Wireless Network

You need more light. Use the back light function.

If not helpful, you may wish to consider replacing

the basic lens with a more sensitive lens, if the

IP Camera in a very low lighting conditions within the installation area

light environment cannot be improved

The Display Properties Open the Display Properties in your desktop and

Poor image quality

are incorrectly

configured for your

desktop

configure your display to show at least 65’000

colors, i.e., at least 16-bit.

Note: Using only 16 or 256 colors on your computer

will produce dithering artifacts in the image.

The camera is not

focused correctly

Referring to the above, adjust the camera manually

NOTE

If you still have a problem after reading this information, please contact your dealer or check

the FAQ on the INTELLINET ACTIVE NETWORKING web site at

http://www.intellinet-network.com.

Before contacting the technical support team, please make sure that you run the latest

firmware on your Wireless Network IP Camera.

You can obtain the latest firmware here: http://www.intellinet-network.com/ipcamera.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

D. Utilizing IP Addresses on Local Area Network

Introduction

Access to the Internet is achieved via Internet IP addresses. Currently, IP addresses are limited.

There are 5 classes of networks, and each network contains IP addresses. A network can only hold a

limited number of IP addresses. The number of IP addresses depends on the network class. The 5

classes are labeled “A” through “E,” with the most common one being the “C” class network.

IP Construction and Network Class

1. IP Construction

xxx

(xxx: 0-255)

e.g. 192.168.1.1

2. Network Class

A Class: A network that contains IP addresses from 0 to 127 at room ‘X1”

Network ID: X1

Host ID: X2, X3, X4

There are 128 A-Class networks in the world.

B Class: A network that contains IP addresses from 0 to 127 at room ‘X1”

Network ID: X1, X2

Host ID: X3, X4

There are 65, 534 B-Class networks in the world.

C Class: A network that contains IP addresses from 192 to 223 at room ‘X1’.

Network ID: X1, X2, X3

Host ID: X4

The most common network in the world; there are 2,097,152 C-class networks in the world.

D Class: A network that contains IP addresses from 224 to 239 at room ‘X1’. D-class networks

are used for multicasting, and are not allowed for common use.

E Class: A network that contains IP addresses from 240 to 255 at room ‘X1’. E-class networks are

reserved.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

C Class Network

1. Features of Addresses

IP address: The three-digit number in room ‘X4’ is for the Host ID. The number ranges from 0 to

255. Among the numbers, 0 is used for Network ID, 1 is used for Router IP (Gateway address) and

255 are used for Broadcast address. The numbers from 2 to 244 are IP addresses that can be

assigned to Wireless Network IP Cameras, PCs, etc.

Network ID: Identifies a network. Generally the first number assigned is Network ID.

Gateway address: The IP address of the router for connecting Internet and local network.

Broadcast address: The IP address for broadcasting. All devices connected on a local network

have the same Broadcast address.

Subnet Mask: Divides a local network into two remote networks. The Subnet Mask shows the IP

quantity in a certain network. The number that can be used as Subnet Mask is

limited (0, 4, 8, 16, 32, 64, 128)

2. Network Configuration

① To use as one network

Network ID: xxx.xxx.xxx.0

Gateway Address: xxx.xxx.xxx.1

Subnet Mask: 255.255.255.0

Broadcast Address: xxx.xxx.xxx.255

IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.254

② To use as two Sub-networks (1/2 + 1/2)

Sub-Network ID: xxx.xxx.xxx.0

Gateway Address: xxx.xxx.xxx.1

Subnet Mask: 255.255.255.128

Broadcast Address: xxx.xxx.xxx.127

IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.126

Sub-Network ID: xxx.xxx.xxx.128

Gateway Address: xxx.xxx.xxx.129

Subnet Mask: 255.255.255.128

Broadcast Address: xxx.xxx.xxx.255

IP Addresses: xxx.xxx.xxx.130 – xxx.xxx.xxx.254

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

③ To use as three sub-networks (1/4 + 1/4 + 1/2)

Sub-Network ID: xxx.xxx.xxx.0

Gateway Address: xxx.xxx.xxx.1

Subnet Mask: 255.255.255.192

Broadcast Address: xxx.xxx.xxx.63

IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.62

Sub-Network ID: xxx.xxx.xxx.64

Gateway Address: xxx.xxx.xxx.65

Subnet Mask: 255.255.255.192

Broadcast Address: xxx.xxx.xxx.127

IP Addresses: xxx.xxx.xxx.66 – xxx.xxx.xxx.126

Sub-Network ID: xxx.xxx.xxx.128

Gateway Address: xxx.xxx.xxx.129

Subnet Mask: 255.255.255.128

Broadcast Address: xxx.xxx.xxx.225

IP Addresses: xxx.xxx.xxx.130 – xxx.xxx.xxx.256

④ To use as four sub-networks (1/4 + 1/4 + 1/4 + 1/4)

Sub-Network ID: xxx.xxx.xxx.0

Gateway Address: xxx.xxx.xxx.1

Subnet Mask: 255.255.255.192

Broadcast Address: xxx.xxx.xxx.63

IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.62

Sub-Network ID: xxx.xxx.xxx.64

Gateway Address: xxx.xxx.xxx.65

Subnet Mask: 255.255.255.192

Broadcast Address: xxx.xxx.xxx.127

IP Addresses: xxx.xxx.xxx.66 – xxx.xxx.xxx.126

Sub-Network ID: xxx.xxx.xxx.128

Gateway Address: xxx.xxx.xxx.129

Subnet Mask: 255.255.255.192

Broadcast Address: xxx.xxx.xxx.191

IP Addresses: xxx.xxx.xxx.130 – xxx.xxx.xxx.190

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Sub-Network ID: xxx.xxx.xxx.192

Gateway Address: xxx.xxx.xxx.193

Subnet Mask: 255.255.255.192

Broadcast Address: xxx.xxx.xxx.255

IP Addresses: xxx.xxx.xxx.194 – xxx.xxx.xxx.254

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

E. Updating Firmware

CAUTION

The process to update the current firmware is already installed into your Wireless Network IP Camera

Follow the instruction in this manual. During the process, do not expose the camera to physical shock

nor disconnect network and power. Otherwise, your Wireless Network IP Camera can be damaged

seriously, which may result improper operation or failure.

If you are unable to update the firmware or the Wireless Network IP Camera does not operate properly

after updating, please contact your dealer.

Identify the Version of Firmware

You can identify the version of Wireless Network IP Camera’s Firmware on the System

Configuration Page. It is also displayed on the camera's login page.

(You may check the version of your Wireless Network IP Camera firmware first and then update if

necessary.)

Follow these steps to check the installed version of firmware

① Connect to your Wireless Network IP Camera home page.

② Click “Administrator Menus.”

③ Move to System Configuration Page and check the version of firmware.

Download New Firmware

You can download the latest firmware over the Internet at the INTELLINET ACTIVE

NETWORKING website: www.intellinet-network.com/ipcamera.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Install New Firmware

The Wireless Network IP Camera can be upgraded via the LAN or remotely over the Internet.

Follow these steps to install new firmware:

① Confirm that the Wireless Network IP Camera is

connected to your PC. (As long as you can

access your Wireless Network IP Camera Home

page, you can upgrade its firmware.)

② Execute the upgrade utility (included in ZIP file).

③ Enter the camera’s IP address, upgrade

port number, Admin ID and password configured

on the Network Configuration page.

And then press “start upgrade” button.

You may see the upgrading status.

Upgrading levels are divided into 4 steps from

“Transferring Firmware” to “Verify flash memory”.

(Each step is indicated on progress bar.)

④ When upgrading is complete, a message appears.

"Firmware Upgrade Completed."

Click the “OK” button.

The Upgrade process must not be interrupted!

If the network connection fails during the upgrade, the camera will be damaged.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

F. The I/O Connector

The I/O Connector provides the physical interface to a digital output, and a single digital photo-

coupled input that is used for connecting a variety of external alarm devices to the Wireless Network

IP Camera; including, IR-sensors, switches and alarm relay.

In combination with the configurable alarm facilities, you can quickly develop a variety of security

applications that are triggered on time- or alarm-based events. The connector can also be utilized as

an alternative connection point for supplying DC power to the unit.

Function

Description

Power GND (-)

Power DC12V (+)

Digital Out (+)

Power for the external input/output devices (-)

Power for the external input/output devices (+)

Output to the external output devices (+)

Output to the external output devices (-)

Input for the external input devices (+)

Input for the external input devices (-)

Digital Out GND (-)

Digital In (+)

Digital In GND (-)

1-2 PIN

To supply external devices with power. PIN1 is connected to GND terminal of device’s power and

PIN2 is connected to (+) terminal. However, the external device should be less DC 12V as a voltage

and 200mA as an electric current.

3-4 PIN

PIN3 is connected to (+) terminal of an external output device; PIN4 is connected to GND terminal

of it. The Wireless Network IP Camera makes the external output device operating by sending a

signal to it. However, the external device should be less than DC 12V and 200mA.

5-6 PIN

PIN5, 6 are connected to the signal output terminal of external input device such as infrared sensor

or alarm sensor. (The behavior of pins 5 and 6 can be controlled in the EVENT TRIGGER

CONFIGURATION of the Administrator Menu)

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

G. RS 232 CABLE

The Serial Connector

In absence of a local network connection, the RS232 serial connector provides a physical interface

for connecting a PTZ device or computer to the Wireless Network IP Camera. This means that

Wireless Network IP Camera can operate as a standalone unit, -independent of any computer

network. Users can connect to theWireless Network IP Camera by external mode.

DSUB 9 PIN FEMALE

DIN 8 PIN MALE

DIN8P MALE TO DSUB9P FEMALE

PIN NAME

RTS

DIN 8 PIN MALE

DSUB 9 PIN FEMALE

CTS

TXD

GND

RXD

DTR

DCD

PIN Function

RTS : Return to send

CTS : Clear to send

TXD : Transmit data

RXD : Receive data

DTR : Data terminal ready

GND : Ground

DSR : Data signal ready

RI : (Ring LED)

CD : (Carrier detect)

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

H. Dynamic Domain Name Service (DDNS)

Your internet Service Provider (ISP) provides you at least one IP address which you use to connect

to the Internet. The address you get may be static, meaning it never changes, or dynamic, meaning

it’s likely to change periodically. Just how often it changes depends on your ISP. A dynamic IP

address complicates remote access since you may not know what your current WAN IP address is

when you want to access your network over the Internet. The solution to the dynamic IP address

problem comes in the form of a dynamic DNS service.

The Internet uses DNSs to lookup domain names and translates them into IP addresses. Domain

names, such as www.intellinet-network.com , are easy to remember aliases for IP addresses. A

dynamic DNS service is unique because it provides a means of updating your IP address so that your

listing will remain current when your IP address changes. There are several excellent DDNS services

available on the Internet, and best of all they’re free. Two excellent DDNS services are www.ods.org

(ODS) and www.DynDNS.org. You’ll need to register with the service and set up the domain name

of your choice to begin using it. Please refer the the home page of the service for detailed

instructions.

A DDNS service works by uploading your WAN IP address to its servers periodically, your gateway-

router may support DDNS directly, in which case you can enter your DDNS account information

into your router, and it will update the DDNS servers automatically when your IP address changes.

Please consult your router’s documentation for more information. If your router does not support

DDNS, you can run a small client utility on any PC on your network, which will perform the

updating. The client utility is usually provided for free by the service. Check the service’s web page

for further information, terms and conditions.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

How to use ODS DDNS service

1. Access ODS home page (www.ods.org).

2. To register your ID, select REGISTER and then register your ID/ password. After that you

just log in with registered ID/password.

3. After you log in, you will see the following page.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

If you want to use normal DDNS service among many services, you should fill in the blanks in

the circled box and then click “Add Host.”

① Host: write the name you want.

② Domain: Select the domain you want (i.E. sphere-web.com)

③ Type: Select ‘A’ (‘A’ is normal)

④ Target: Write initial IP of equipment but just write any IP address that is in the form of

“xxx.xxx.xxx.xxx”

⑤ TTL Priority: DO NOT select. This is an option.

If you want to select “intellinet.sphere-web.com.org” for domain name, write ‘intellinet’ in Host

item and then select sphere-web.com for domain. Otherwise, please refer to the premium service.

NOTE

After completing the setup, you should set DDNS registration for the Wireless Network

IP Camera

Example Configuration:

Your ODS Username: intellinet

Your ODS Password: 550703

Your ODS Domain Name: cam.sphere-web.com

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

How to use DynDNS DDNS server

1. Access the Dyndns home page (www.dyndns.org).

2. If you didn’t register your ID, click “Sign Up Now” and then register your ID.

Otherwise, login with registered ID.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

3. Click “Add Host”, and then go to the next page.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

4. Enter the domain name you want and leave other items unchanged, and then Click “Add Host”

button to register. If you want to know details of any field, please refer to FAQ for each

home page.

5. You will see this confirmation page.

NOTE

After completing DynDNS setting, you should set DDNS registration for the Wireless Network

IP Camera

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

DDNS registration for the Wireless Network IP Camera

1. After you set ODS or DynDNS successfully, you should move to administration -> network

configuration.

2. In DDNS Registration, select DDNS server (ODS or Dyndns) you want.

Enter ID/password that you registered and fill domain name that you set in each home page.

(ex: intellient.ods.org)

„ Before setting DDNS, you should register ID/password and domain name in ODS

or Dyndns DDNS service.

3. If registration is finished successfully, you will see “Registration Success.” Now, you can

connect to the Wireless Network IP Camera by a domain name that you registered.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

I. High-Speed Solutions

This information is to help you access high-speed Internet services, such as xDSL, or a cable modem

connection. However, since some high-speed Internet services may provide only one external IP

address that may not be static,, there are several practical issues to consider.

AVAILABLE IPADDRESS

An ISP (Internet Service Provider) ideally will provide you with several static IP addresses – in

which case you can assign any one of these to your Wireless Network IP Camera to make it fully

accessible over the Internet. However, if your service provider supplies you with only one IP address,

which is often the case, this IP number is normally assigned to your PC,-leaving no connection

available for your Wireless Network IP Camera.

What can you do if your ISP is unable to provide you with an IP number?

There are a number of other options to consider, including:

NAT BOX

Short for Network Address Translator, NAT is an Internet standard that allows a local-area network

(LAN) to use one set of IP addresses for internal traffic and a second set of addresses for external

traffic. A NAT box located where your LAN meets the Internet will handle all of the necessary IP

address translations and provides:

z Internal IP addresses that are unique to your network – with no possibility of conflict with

IP Addresses used by other companies and organizations.

z The possibility of combining multiple ISDN connections into a single Internet connection.

z An effective firewall for hiding internal IP addresses.

NAT Feature in Windows 2000

Utilize the NAT feature in Windows 2000 to allow multiple Ethernet cards in your PC, and you can

then use one of port for the Internet and the other for your internal network. With this solution, you

can let your Wireless Network IP Camera upload image streams to an external Web Server that is

maintained and located with your ISP.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

ROUTERS AND FIREWALLS

Another solution is to use one of several small routers/firewalls currently available on the market.

These provide the necessary NAT functionality and allow complete independence for your PC,

which can be switched off or rebooted without affecting the image transmission from your Wireless

Network IP Camera.

WINGATE SERVER SOFTWARE

Running on a single Windows 95/98/2000 or NT computer, this software allows multiple users

simultaneous access to the Internet through a LAN or higher-speed line, such as xDSL or cable

modem connection; and effectively shares a single Internet connection with almost any type of client

computer running TCP/IP.

For more advanced users, the WinGate 3.0 Standard and Pro versions also allow the administrator to

change the IP bindings so that external requests may be routed specifically to your Wireless Network

IP Camera – running behind the WinGate software.

NOTE

NAT, or Network Address Translator (Virtual LAN): A hardware device currently being

developed and used to extend the Internet addresses already in use. NAT has been suggested as an

alternative to adopting IPv6 (IPng). It allows duplicate IP addresses to be used within a

corporation and unique addresses outside. It is defined in RFC 1631.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

J. Reinstating the Factory Default Settings

This information explains how to set the default settings in the Wireless Network IP Camera. In

certain circumstances it may become necessary to restart or reinstate the Factory Default settings for

your Wireless Network IP Camera: This is performed by pressing the Reset Button, or using the

Hyper Terminal Setting. Follow these instructions to reinstate the product factory default settings

By Pressing Reset Button

① Using a paper clip or any sharp pin, press the reset button on the backside of Wireless

Network IP Camera.

② Switch off the Wireless Network IP Camera by disconnecting the power cable.

③ Press and keep the Reset Button pressed, and then reconnect the power supply cable.

Keep the Reset Button pressed until the Operating Status LED (Green) blinks three times.

(Note that this may take up to 10~15 seconds), then release the button.

By Using the Web Browser (System Configuration Page)

You can restore the factory default values in the Administrator Menu, System Configuration,

Click on RESTORE DEFAULTS. See image below:

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

By Using Hyper Terminal (Advanced Users only)

① Execute Hyper Terminal as

described in Chapter “4.3.1

Configuring Hyper Terminal”

② Supply the power to the Wireless

Network IP Camera.

③ After a while, the count down

starts with the message

“Press 'p' key to stop auto-boot or

Load-Default-Button under the

NetCam for 3 seconds...”

.At this time, press the ‘p’ key. Then,

[Wireless Network IP Camera Boot]

prompt shows like the right side

image.

④ When you enter ‘w’, Administrator ID & password reset as factory default ‘admin.’

NOTE

Reinstating the original default settings will cause all parameters (Including IP address) to reset.

Factory default setting

Administrator ID: admin

Administrator Password: admin

Guest ID: guest

Guest Password: guest

IP Address: 192.168.1.221

Subnet Mask Address: 255.255.255.0

Gateway Address: 192.168.1.1

Server IP Address: 192.168.1.200

Compression Rate: Level 1

Image Size: QVGA

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

K. Glossary of Terms

Active-X – A control (or set of rules) used by a browser. Active-X controls are often downloaded

and installed automatically as required.

ARP – Address Resolution Protocol. A method for finding a host's Ethernet address from its Internet

address. The sender broadcasts an ARP packet containing the Internet address of another host and

waits for it (or some other host) to send back its Ethernet address. Each host maintains a cache of

address translations to reduce delay and loading. ARP allows the Internet address to be independent

of the Ethernet address but it only works if all hosts support it. The ARP command can be used to set

the IP addresses for your product.

CGI – A standard for running external programs from a World-Wide Web HTTP server. CGI

specifies how to pass arguments to the executing program as part of the HTTP request. It also

defines a set of environment variables. Commonly, the program will generate some HTML which

will be passed back to the browser, but it can also request URL redirection. Also, a set of rules (or a

program) that allows a Web Server to communications with other programs.

DSL –Digital Subscriber Loop, A family of digital telecommunications protocols designed to allow

high-speed data communication over the existing copper telephone lines between end-users and

telephone companies.

DHCP – A protocol that provides a means to dynamically allocate IP addresses to computers on a

local area network. The system administrator assigns a range of IP addresses to DHCP and each

client computer on the LAN has its TCP/IP software configured to request an IP address from the

DHCP server. The request and grant process uses a lease concept with a controllable time period.

Ethernet –A widely used networking standard.

Firewall –A virtual barrier between a LAN (Local Area Network) and other networks, e.g., the

Internet.

Frame Grabber Card – Plug-in hardware for “grabbing” images.

FTP – A client-server protocol that allows a user on one computer to transfer files to and from

another computer over a TCP/IP network. Also the client program the user executes to transfer files.

It is defined in STD 9, RFC 959.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

HTML – A markup language used to structure text and multimedia documents and to set up

hypertext links between documents, used extensively on the World Wide Web.

HTTP – A protocol used to request and transmit files, especially web pages and webpage

components, over the Internet or other computer network.

Intranet – A privately maintained computer network that can be accessed only by authorized

persons, especially members or employees of the organization that owns it.

IP (Internet Protocol) –. The network layer for the TCP/IP protocol suite widely used on Ethernet

networks, defined in STD 5, RFC 791. IP is a connectionless, best-effort packet switching protocol.

It provides packet routing, fragmentation and re-assembly through the data link layer.

IP Number (address) – A unique number used by a computer on the network to allow it to be

identified and found.

JPEG – A standard image format, used widely for photographs. Also known as JPG.

LAN (Local Area Network) –. A data communications network which is geographically limited

(typically to a 1 km radius), allowing easy interconnection of terminals, microprocessors and

computers within adjacent buildings. Ethernet and FDDI are examples of standard LANs.

PING – A protocol that sends a message to another computer and waits for acknowledgment, often

used to check if another computer on a network is reachable.

PPP (Point-to-Point Protocol) – A method allowing one computer to connect to another, usually via

a modem over a phone line.

Protocol - A set of formal rules describing how to transmit data, especially across a network. Low-

level protocols define the electrical and physical standards to be observed, bit- and byte-ordering and

the transmission and error detection and correction of the bit stream. High-level protocols deal with

the data formatting, including the syntax of messages, the terminal to computer dialogue, character

sets, sequencing of messages etc.

SMTP – Simple Mail Transfer Protocol

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

TCP/IP (Transmission Control Protocol/Internet Protocol) –. The wide-area-networking protocol

that makes the Internet work. TCP/IP is used on many networks, including the Internet. TCP keeps

track of the individual packets of information and IP contains the rules for how the packets are

actually sent and received.

URL (Uniform Resource Locator) – An “address” on the network.

WAN (Wide–Area–Network) – A communications network that uses such devices as telephone lines,

satellite dishes, or radio waves to span a larger geographic area than can be covered by a LAN.

Wizard – A program designed specifically to guide the user through a procedure. Typically used for

installation and configuration. Installshield Wizard is required to download Active-X manually.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRELESS NETWORK IP CAMERA User’s Guide

Limited Lifetime Warranty

* This INTELLINET ACTIVE NETWORKING® product is covered by the following warranty. *

This warranty applies to the original purchaser only. This warranty covers defects in material and

workmanship for the life of the original purchaser, for as long as the product is owned by the

original purchaser. Implied warranties end when the original purchaser no longer owns the product;

this limitation includes the implied warranty of merchantability. Some states or countries do not

allow limitations on how long an implied warranty lasts, so the above limitation may not apply to

you. * If this product fails during the warranty period because of a defect in material or

workmanship, we will repair or replace the product, at our option. Repair parts may be

remanufactured or refurbished. * This warranty does not cover damaged caused by: improper

installation; improper repairs, servicing, or alterations; use of supplies or parts that do not meet our

specifications; unauthorized modifications; failure to follow instructions; normal wear and tear;

natural disasters and accidents, including fire, water, lightning, and other acts of nature; anything

that is not a defect in material or workmanship. This warranty also does not cover: damage to items

that occurs during shipment to us; lost data, lost time, damaged software, or loss of revenue or

profits; losses covered by your insurance; shipping costs and expenses; incidental and consequential

damages not listed above. Some states or countries do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation or exclusion may not apply to you. *

How to get warranty service: Keep your original receipt or other proof of purchase. Notify us within

one week of the occurrence. Provide your name, your address, the serial number of the product, a

description of the problem, and your original sales slip or invoice. If requested by us, ship to us the

damaged product.

For more information or to file a warranty claim, visit www.intellinet-network.com. This warranty

gives you specific legal rights, and you may also have other rights depending on your state or

country.

IC INTRACOM

World Headquarters

550 Commerce Boulevard

Oldsmar, FL 34677

+1-813-855-0550

www.intellinet-network.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Integra Stereo Receiver DTR 51 User Manual
Invacare Mobility Aid 1110266 User Manual
JBL Speaker S36AWII User Manual
Jenn Air Oven JJW9627DDB User Manual
Jensen Automobile Electronics VCCYL35N User Manual
JVC CRT Television TM 2100PN User Manual
Jwin Conference Phone JT P670 User Manual
Kenmore Water System ULTRASOFT 175 625388170 User Manual
Kicker Speaker S10X User Manual
Kramer Electronics Switch SI VGAT UXGA User Manual