|
MI935
LGA775 Core™ 2 Duo
Intel® Q35 Chipset
Mini-ITX Motherboard
USER’S MANUAL
Version 1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
MI935 User’s Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is intentionally left blank.
iv
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Introduction
Checklist
Your MI935 Core 2 Duo motherboard package should include the items
listed below:
•
•
•
•
•
•
The MI935 motherboard
This User’s manual
1 x I/O shield
1 x IDE cable
1 x SATA cable
1 CD containing the following:
•
•
Chipset Drivers
Flash Memory Utility
MI935 User’s Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Product Description
The MI935 Mini-ITX motherboard is designed for either the Intel®
Core™2 Duo or Core™2 Quad processors of up to 1333MHz FSB.
It is based on the Intel’s Q35 Express chipset and it comes with
two single-channel DDR2 memory slots and 4GB memory
capacity for faster system responsiveness and support of 64-bit
computing. The new IBASE motherboards are aimed for high
performance PCs in the digital, communications and industrial
sector.
On board is one PCI Express x16 slot that offers up to 3.5X the
bandwidth over traditional PCI architecture to support the latest
high-performance graphics cards. Dual independent display
comes to life with the onboard Intel® Q35 integrated graphics for
CRT and an optional SDVO card supporting either an LVDS or
DVI display interface. LAN functionality is supported with a 10/100
Ethernet controller or with two Gigabit Ethernet controllers.
MI935 is expandable, with the use of an adaptor card, ID394, to
support 2 or 4 serial ports, or ID395 to support TPM 1.2 security
function. Other useful features on the board include two SATA II
ports, one eSATA port, eight USB 2.0 interface, watchdog timer,
digital I/O and two serial ports. Board dimensions are 170mm by
170mm. (Note: CPU power consumption – under 95watt
recommended.)
MI935 FEATURES
y Intel® Q35 Express Chipset Based
y Support LGA775 Intel® Core™2 Duo/Quad CPU
y Support up to 1333MHz FSB
y Support up to 4GB DDRII 800/667 memory
y 1 x PCI Express (x16)
y Support one 10/100 or two Gigabit LAN on board
y 2x SATA II, 1x eSATA, 1x IDE, 8x USB 2.0,
2x COM, 7.1Ch.HD Audio
2
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Specifications
Mini ITX (for performance desktop market)
Form Factor
Processor
Socket LGA775, Supports the Intel Core 2 Duo and Intel Core2 Quad
processors, and Intel Celeron 400 (Conroe-L) Sequence processor.
800/1066/1333 MHz
FSB
Intel Q35 Chipset:
Chipset
•
•
•
•
•
Intel Q35 Graphic Memory Controller Hub (GMCH)
Intel ICH9/ICH9R I/O Controller Hub
Award BIOS: footprint from SPI, supports ACPI, SMBIOS
2 x 240-pin DDRII 667/800 DIMM sockets, support one channels,
Supports max. 4 GB system memory
BIOS
Memory
Intel Q35 integrated graphic subsystem (GMA3100), dual
independent display available through on-board VGA and PCI-e
x16 expansion adapter (DVI or LVDS) or VGA card
LAN1: dual Footprint support option:
Video
LAN
•Intel 82566DM Nineveh 10/100/1000 LAN
•Intel 82562V Ekron-N 10/100
LAN2: Marvell 88E8053 PCI-express Gigabit LAN controller x1
Intel ICH9/ICH9R built-in USB 2.0 host controller, supports 8 ports:
•4 ports in the rear I/O region
USB
•4 ports with on-board headers
Intel ICH9 built-in SATA II controller (3.0Gb/sec) w/ 2 ports. ICh9R
SATA II
Built-in raid 0,1 or AHCI (for eSATA)
Jmicron JM368 (PCI-e to PATA) x1 for 1 PATA channel
Intel ICH9/ICH9R built-in high definition audio w/ Realtek ALC888
Codec
IDE
Audio
Winbond W83627EHG: COM1 (RS232), COM2 (RS232/422/485) &
Hardware monitor
LPC I/O
Hardware Monitor
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Two fan connectors with tachometer support
CPU fan connector supports 4-wire fan with PWM control
Supports three thermal diodes (CPU die + 2 on-board)
Voltage monitoring for VCC (processor), 3.3V, 5V, and 12V
Mini-DIN x 1 for PS/2 KB & MS
Edge Connectors
Esata connectorx1(for ICH9R)
DB9 + DB15 stack connector x 1 for COM1 & VGA
RJ45 + dual USB stack connector x2 for LAN1~2 and USB1~4
Triple (3x1) phone jack connector x1 for High-Definition Audio
Standard SATA (7-pin shrouded vertical) connector x2
4x2 pins pin-header x2 for USB 5-6,7-8.
5x2 pins DF11-10 x1 for COM2 (RS232/422/485)
5x2 pins pin-header x1 for Digital I/O
5X2 pins pin-headerx1 for audio front.
On Board Headers /
Connectors
40 pins box-header x1 for IDE
4 pins pin--header x1 for CPU fan & system fan
3 pins pin--header x2 for system fan
PCI-express (x16) slot x1
Expansion
8x2 pins pin header x1 for adaptor card:
-
-
ID394 (2 or 4 serial ports)
ID395 (TPM function)
Yes (256 segments, 0, 1, 2…255 sec/min)
4 in and 4 Out
Watchdog Timer
Digital IO
LAN Wakeup
Other
24 pins ATX main power + 4 pins 12V
+5V, +3.3V, +12V, -12V & 5VSB
170 x 170mm
Power Connector
System Voltage
Board Size
MI935 User’s Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Installing the CPU
The MI935 motherboard supports an LGA 775 processor socket for
Intel® Core 2 Duo processors.
The LGA 775 processor socket comes with a lever to secure the
processor. Refer to the pictures below, from left to right, on how to place
the processor into the CPU socket. Please note that the cover of the
LGA775 socket must always be installed during transport to avoid
damage to the socket.
ATX Power Installation
The system power is provided to the motherboard with the ATX2 and
ATX1 power connectors. ATX2 is a 24-pin power connector and ATX1
is a 4-pin 12V power connector.
The 24-pin power connector can to be connected to a standard 20-pin
ATX power connector in a standard ATX power supply (Min. 400watt).
Note: The power supply 5VSB voltage must be at least 2A.
6
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Installing the Memory
The MI935 motherboard supports four DDR2 memory sockets for a
maximum total memory of 4GB in DDR memory type. It supports
DDR2 667/800MHz.
Basically, the system memory interface has the following features:
Supports two 64-bit wide DDR data channels
Available bandwidth up to 6.4GB/s (DDR2 800) for two-channel
mode.
Supports 256Mb, 512Mb, 1Gb DDR2 technologies.
Supports only x8, x16, DDR2 devices with four banks
Supports only unbuffered DIMMs
Supports opportunistic refresh
Up to 32 simultaneously open pages (four per row, four rows
maximum)
MI935 User’s Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Setting the Jumpers
Jumpers are used on the motherboard are used to select various settings
and features according to your needs and applications. Contact your
supplier if you have doubts about the best configuration for your needs.
The following lists the connectors and their respective functions.
8
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
JP7: Clear CMOS Contents
Use JP7, a 3-pin header, to clear the CMOS contents. Note that the
ATX-power connector should be disconnected from the motherboard
before clearing CMOS.
JP7
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
JP1, JP2, JP3: RS232/422/485 (COM2) Selection
COM1 is fixed for RS-232 use only.
COM2 is selectable for RS232, RS-422 and RS-485.
ID394: COM3 and COM4 are fixed for RS-232 use only. The following
table describes the jumper settings for COM2 selection.
COM2
Function
RS-232
RS-422
RS-485
JP3:
1-2
JP3:
3-4
JP3:
5-6
Jumper
Setting
JP1:
JP1:
JP1:
(pin closed) 3-5 & 4-6
1-3 & 2-4
1-3 & 2-4
JP2:
JP2:
JP2:
3-5 & 4-6
1-3 & 2-4
1-3 & 2-4
10
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Connectors on MI935
The connectors on MI935 allows you to connect external devices such as
keyboard, floppy disk drives, hard disk drives, printers, etc. The
following table lists the connectors on MI935 and their respective
functions.
CN5: Audio Connector.................................................................................... 15
CN3: eSATA HDD Connector ........................................................................ 15
IDE1: Primary IDE Connectors....................................................................... 16
J2: Digital I/O Connector (4 in, 4 out)............................................................. 17
J5: Audio Front Header ................................................................................... 17
J6, J7: USB4/5, USB6/7 Connectors ............................................................... 17
MI935 User’s Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Connector Locations on MI935/MI935F/MI935RF
ATX1: ATX 12V Power Connector.......................................................................................................13
CPU_FAN1: CPU Fan Power Connector..............................................................................................13
CN5: Audio Connector...........................................................................................................................15
IDE1: Primary IDE Connectors..............................................................................................................16
J5: Audio Front Header ..........................................................................................................................17
J6, J7: USB4/5, USB6/7 Connectors......................................................................................................17
J8: Power LED........................................................................................................................................17
J10: System Function Connector............................................................................................................18
12
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
ATX2: 24-pin ATX Power Connector
Signal Name Pin # Pin # Signal Name
3.3V
-12V
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
3.3V
3.3V
Ground
+5V
Ground
+5V
Ground
Power good
5VSB
Ground
PS-ON
Ground
Ground
Ground
-5V
+5V
+5V
+5V
Ground
10
11
12
+12V
+12V
+3.3V
ATX1: ATX 12V Power Connector
This connector supplies the CPU operation voltage
Pin #
Signal Name
Ground
Ground
+12V
1
2
3
4
+12V
CPU_FAN1: CPU Fan Power Connector
Pin #
Signal Name
Ground
+12V
1
2
3
4
Sense
Control
SYS FAN1, 2: System Fan Power Connectors
Pin #
Signal Name
Ground
+12V
1
2
3
Sense
MI935 User’s Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
CN4: PS/2 Keyboard and PS/2 Mouse Connectors
Keyboard Signal
Keyboard data
N.C.
GND
5V
Keyboard clock
N.C.
Pin #
Mouse Signal
Mouse data
N.C.
GND
5V
Mouse clock
N.C.
1
2
3
4
5
6
Mouse (top)
Keyboard (bottom)
CN2, J3: COM1/2 Serial Ports
CN2 (COM1) is a DB-9 connector, while J3 is a COM pin-header
connector.
Signal Name
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
GND, ground
Pin # Pin #
Signal Name
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
Not Used
1
2
3
4
5
6
7
8
9
10
J3: COM2 is jumper selectable for RS-232, RS-422 and RS-485.
Pin #
Signal Name
RS-232
DCD
RX
R2-422
TX-
RS-485
DATA-
DATA+
NC
NC
Ground
NC
NC
NC
NC
1
2
3
4
5
6
7
8
9
TX+
RX+
RX-
Ground
NC
NC
NC
NC
TX
DTR
Ground
DSR
RTS
CTS
RI
10
NC
NC
NC
14
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
CN1: VGA CRT Connector
Signal Name Pin # Pin # Signal Name
Red
Blue
1
3
2
4
Green
N.C.
GND
5
6
GND
GND
7
8
GND
VCC
N.C.
HSYNC
DDCCLK
9
10
12
14
GND
DDCDATA
VSYNC
11
13
15
CN6: Marvell 88E8053 PCI-express Gigabit LAN and USB2/3
Connector
CN7: Intel 82562V 10/100 or Intel 82566DM GbE RJ-45 and
USB0/1 Connector
Note: 10/100 LAN for MI935; Dual Gigabit LAN for MI935F
CN5: Audio Connector
CN4 is a 3-jack audio connector
CN3: eSATA HDD Connector
Pin # Signal Name
1
2
3
4
5
6
7
Ground
TX+
TX-
Ground
RX-
RX+
Ground
MI935 User’s Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
CN9, CN8: SATA HDD Connectors
Pin # Signal Name
1
2
3
4
5
6
7
Ground
TX+
TX-
Ground
RX-
RX+
Ground
IDE1: Primary IDE Connectors
Signal Name
Pin #
Pin #
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
1
2
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Protect pin
Ground
3
4
5
6
8
7
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
DRQ0
Host IOW
Host IOR
IOCHRDY
DACK0
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
IRQ14
Address 1
Address 0
Chip select 0
Activity
IDE1
16
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
J2: Digital I/O Connector (4 in, 4 out)
This 10-pin digital I/O connector supports TTL levels and is used to
control external devices requiring ON/OFF circuitry.
Signal Name Pin # Pin # Signal Name
Ground
Out3
Out2
IN3
1
3
5
7
9
2
4
6
8
10
+5V
Out1
Out0
IN1
IN2
IN0
J4: For LPC I/F Adaptor Card
Supports ID394 with Fintek F81216, 2 or 4 serial ports
J5: Audio Front Header
Signal Name Pin # Pin # Signal Name
MIC2_L
MIC2_R
Line2_R
Sense
1
3
5
7
9
2
4
6
8
10
Ground
Presence#
MIC2_ID
NC
Line2_L
Line2_ID
J6, J7: USB4/5, USB6/7 Connectors
Signal Name Pin Pin Signal Name
Vcc
1
3
5
7
2
4
6
8
Ground
USB1+
USB1-
Vcc
USB0-
USB0+
Ground
J8: Power LED
The power LED indicates the status of the main power switch.
Pin # Signal Name
1
2
3
Power LED
No connect
Ground
MI935 User’s Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
J9: SPDIF Out Connector
Pin # Signal Name
1
2
SPDIF out
Ground
J10: System Function Connector
ATX Power ON Switch: Pins 1 and 2
This 2-pin connector is an “ATX Power Supply On/Off Switch” on the
system that connects to the power switch on the case. When pressed, the
power switch will force the system to power on. When pressed again, it
will force the system to power off.
Hard Disk Drive LED Connector: Pins 3 and 4
This connector connects to the hard drive activity LED on control panel.
This LED will flash when the HDD is being accessed.
Pin #
4
3
Signal Name
HDD Active
5V
Reset Switch: Pins 5 and 6
The reset switch allows the user to reset the system without turning the
main power switch off and then on again. Orientation is not required
when making a connection to this header.
+5V and 5VSB Signals: Pins 7 and 8
Pin #
7
8
Signal Name
+5V
+5VSB
PCIE_1: x16 PCI Express Slot
18
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
ID394 LPC Serial Ports Adapter (option)
J1 J2: COM3/4/5/6 Serial Ports
J1 - COM3/4 pin-header connector.
PIN1~PIN10 COM3
PIN11~PIN20 COM4
J2 - COM5/6 pin-header connector.
PIN1~PIN10 COM5
PIN11~PIN20 COM6
Signal Name
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
GND, ground
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
GND, ground
Pin # Pin #
Signal Name
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
Not Used
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
Not Used
1
3
2
4
5
6
7
8
9
10
12
14
16
18
20
11
13
15
17
19
CN1: LPC I/F connectors
Package list:
COM port cable (PK1-20B) x 2
Nylon Nut x 1
Screw x 2
Washer x2
MI935 User’s Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
This page is intentionally left blank.
20
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
BIOS Setup
This chapter describes the different settings available in the Award
BIOS that comes with the board. The topics covered in this chapter are
as follows:
2nd SuperIO Device.................................................................... 42
MI935 User’s Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your
computer system’s ROM supports Intel processors. The BIOS provides
critical low-level support for a standard device such as disk drives, serial
ports and parallel ports. It also adds virus and password protection as
well as special support for detailed fine-tuning of the chipset controlling
the entire system.
BIOS Setup
The Award BIOS provides a Setup utility program for specifying the
system configurations and settings. The BIOS ROM of the system stores
the Setup utility. When you turn on the computer, the Award BIOS is
immediately activated. Pressing the <Del> key immediately allows you
to enter the Setup utility. If you are a little bit late pressing the <Del>
key, POST (Power On Self Test) will continue with its test routines, thus
preventing you from invoking the Setup. If you still wish to enter Setup,
restart the system by pressing the ”Reset” button or simultaneously
pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by
turning the system Off and back On again. The following message will
appear on the screen:
Press <DEL> to Enter Setup
In general, you press the arrow keys to highlight items, <Enter> to
select, the <PgUp> and <PgDn> keys to change entries, <F1> for help
and <Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup
functions and exit choices.
22
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Frequency/Voltage Control
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
ESC : Quit
Ç È Æ Å : Select Item
F10 : Save & Exit Setup
Time, Date, Hard Disk Type…
The section below the setup items of the Main Menu displays the control
keys for this menu. At the bottom of the Main Menu just below the
control keys section, there is another section, which displays information
on the currently highlighted item in the list.
Note:
If the system cannot boot after making and saving system
changes with Setup, the Award BIOS supports an override to
the CMOS settings that resets your system to its default.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both Award and your system
manufacturer to provide the absolute maximum performance
and reliability. Changing the defaults could cause the system
to become unstable and crash in some cases.
MI935 User’s Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Standard CMOS Setup
“Standard CMOS Setup” choice allows you to record some basic
hardware configurations in your computer system and set the system
clock and error handling. If the motherboard is already installed in a
working system, you will not need to select this option. You will need to
run the Standard CMOS option, however, if you change your system
hardware configurations, the onboard battery fails, or the configuration
stored in the CMOS memory was lost or damaged.
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Fri, Oct 20, 2006
16 : 11 : 00
Item Help
Menu Level >
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
IDE Channel 2 Master
IDE Channel 3 Master
IDE Channel 4 Master
IDE Channel 4 Slave
None
None
None
None
None
None
None
None
Change the day, month,
Year and century
Video
EGA/VGA
Halt On
All , But Keyboard
Base Memory
640K
Extended Memory
Total Memory
2086912K
2087936K
At the bottom of the menu are the control keys for use on this menu. If
you need any help in each item field, you can press the <F1> key. It will
display the relevant information to help you. The memory display at the
lower right-hand side of the menu is read-only. It will adjust
automatically according to the memory changed. The following
describes each item of this menu.
Date
The date format is:
Day :
Sun to Sat
1 to 12
1 to 31
Month :
Date :
Year :
1999 to 2099
24
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
To set the date, highlight the “Date” field and use the PageUp/
PageDown or +/- keys to set the current time.
Time
The time format is: Hour : 00 to 23
Minute : 00 to 59
Second : 00 to 59
To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn>
or +/- keys to set the current time.
IDE Channel Master/Slave
The onboard Serial ATA connectors provide Primary and Secondary
channels for connecting up to four Serial ATA hard disks . Each channel
can support up to two hard disks; the first is the “Master” and the second
is the “Slave”.
Press <Enter> to configure the hard disk. The selections include Auto,
Manual, and None. Select ‘Manual’ to define the drive information
manually. You will be asked to enter the following items.
Capacity :
Cylinder :
Head :
Capacity/size of the hard disk drive
Number of cylinders
Number of read/write heads
Write precompensation
Precomp :
Landing Zone : Landing zone
Sector :
Number of sectors
The Access Mode selections are as follows:
CHS
LBA
(HD < 528MB)
(HD > 528MB and supports Logical Block Addressing)
Large (for MS-DOS only)
Auto
MI935 User’s Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Video
This field selects the type of video display card installed in your system.
You can choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA
or PGA monitor adapters. (default)
Power up in 40 column mode.
Power up in 80 column mode.
For Hercules or MDA adapters.
CGA 40
CGA 80
MONO
Halt On
This field determines whether or not the system will halt if an error is
detected during power up.
No errors
The system boot will not be halted for any error
that may be detected.
All errors
Whenever the BIOS detects a non-fatal error,
the system will stop and you will be prompted.
The system boot will not be halted for a
keyboard error; it will stop for all other errors
The system boot will not be halted for a disk
error; it will stop for all other errors.
All, But Keyboard
All, But Diskette
All, But Disk/Key
The system boot will not be halted for a key-
board or disk error; it will stop for all others.
26
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Advanced BIOS Features
This section allows you to configure and improve your system and
allows you to set up some system features according to your preference.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
CPU Feature
Press Enter
Press Enter
Enabled
Enabled
Removable
Hard Disk
CDROM
Enabled
On
ITEM HELP
Hard Disk Boot Priority
CPUL3 Cache
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Boot Up NumLock Status
Gate A20 Option
Fast
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
Disabled
6
250
Setup
APIC Mode
Enabled
1.4
Non-OS2
Disabled
MPS Version Control for OS
OS Select For DRAM>64MB
Small Logo (EPA) Show
CPU Feature
Press Enter to configure the settings relevant to CPU Feature.
Hard Disk Boot Priority
With the field, there is the option to choose, aside from the hard disks connected,
“Bootable add-in Cards” which refers to other external devices.
CPU Cache
Cache memory is additional memory that is much faster than conventional
DRAM (system memory). CPUs from 486-type on up contain internal cache
memory, and most, but not all, modern PCs have additional (external) cache
memory. When the CPU requests data, the system transfers the requested data
from the main DRAM into cache memory, for even faster access by the CPU.
These items allow you to enable (speed up memory access) or disable the cache
function. By default, these items are Enabled.
Quick Power On Self Test
When enabled, this field speeds up the Power On Self Test (POST) after
the system is turned on. If it is set to Enabled, BIOS will skip some
items.
First/Second/Third Boot Device
These fields determine the drive that the system searches first for an
operating system. The options available include Removable, Hard Disk,
CDROM, Legacy LAN and Disabled.
MI935 User’s Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Boot Other Device
These fields allow the system to search for an OS from other devices
other than the ones selected in the First/Second/Third Boot Device.
Boot Up NumLock Status
This allows you to activate the NumLock function after you power up
the system.
Gate A20 Option
This field allows you to select how Gate A20 is worked. Gate A20 is a
device used to address memory above 1 MB.
Typematic Rate Setting
When disabled, continually holding down a key on your keyboard will
generate only one instance. When enabled, you can set the two typematic
controls listed next. By default, this field is set to Disabled.
Typematic Rate (Chars/Sec)
When the typematic rate is enabled, the system registers repeated
keystrokes speeds. Settings are from 6 to 30 characters per second.
Typematic Delay (Msec)
When the typematic rate is enabled, this item allows you to set the time
interval for displaying the first and second characters. By default, this
item is set to 250msec.
Security Option
This field allows you to limit access to the System and Setup. The default
value is Setup. When you select System, the system prompts for the User
Password every time you boot up. When you select Setup, the system
always boots up and prompts for the Supervisor Password only when the
Setup utility is called up.
APIC Mode
APIC stands for Advanced Programmable Interrupt Controller. The
default setting is Enabled.
MPS Version Control for OS
This option is specifies the MPS (Multiprocessor Specification) version
for the OS. MPS version 1.4 added extended configuration tables to
improve support for multiple PCI bus configurations and improve future
expandability. The default setting is 1.4.
28
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
OS Select for DRAM > 64MB
This option allows the system to access greater than 64MB of DRAM
memory when used with OS/2 that depends on certain BIOS calls to
access memory. The default setting is Non-OS/2.
Small Logo (EPA) Show
The EPA logo appears at the right side of the monitor screen when the
system is boot up. The default setting is Disabled.
MI935 User’s Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Advanced Chipset Features
This Setup menu controls the configuration of the chipset.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Timing Selectable
CAS Latency Time
By SPD
Auto
ITEM HELP
Menu Level >
DRAM RAS# to CAS# Delay
DRAM RAS# Precharge
Precharge dealy (tRAS)
System Memory Frequency
System BIOS Cacheable
Memory Hole at 15M-16M
PCI Express Root Port Func
Auto
Auto
Auto
By SPD
Enabled
Disabled
Press Enter
** VGA Setting **
PEG/On Chip VGA Control
On-Chip Frame Buffer Size
DVMT Mode
Auto
8MB
DVMT
DVMT/FIXED memory Size
SDVO Device Setting
SDVO LVDS Protocol
SDVO Panel
Boot Display
TV Standard
128MB
None
1CH 18 bit
1024x768
CRT+LVDS
Off
Video Connector
TV Format
Automatic
Auto
DRAM Timing Selectable
This option refers to the method by which the DRAM timing is selected.
The default is By SPD.
CAS Latency Time
You can select CAS latency time in HCLKs of 3/3 or 4/4. The system
board designer should set the values in this field, depending on the
DRAM installed. Do not change the values in this field unless you
change specifications of the installed DRAM or the installed CPU. The
choices are 3, 4 and 5.
DRAM RAS# to CAS# Delay
This option allows you to insert a delay between the RAS (Row Address
Strobe) and CAS (Column Address Strobe) signals. This delay occurs
when the SDRAM is written to, read from or refreshed. Reducing the
delay improves the performance of the SDRAM.
DRAM RAS# Precharge
This option sets the number of cycles required for the RAS to
accumulate its charge before the SDRAM refreshes.
30
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Precharge delay (tRAS)
The default setting for the Active to Precharge Delay is Auto.
System Memory Frequency
This field sets the frequency of the DRAM memory installed. The
default setting is Auto. The other settings are DDR667 and DDR800.
System BIOS Cacheable
The setting of Enabled allows caching of the system BIOS ROM at
F000h-FFFFFh, resulting in better system performance. However, if
any program writes to this memory area, a system error may result.
Memory Hole At 15M-16M
In order to improve performance, certain space in memory can be
reserved for ISA cards. This memory must be mapped into the memory
space below 16 MB. The choices are Enabled and Disabled.
PCI Express Root Port Func
Press Enter to configure this field.
On-Chip VGA Setting
The fields under the On-Chip VGA Setting and their default settings are:
PEG/On Chip VGA Control: Auto
On-Chip Frame Buffer Size: 8MB
DVMT Mode: DVMT
DVMT/Fixed Memory Size: 128MB
SDVO Device Setting: None
To use the single DVI setting, install the IBP192-R DVI module; to
use the dual DVI setting, install the IBP192D-R DVI module; and
to use the LVDS+TV or LVDS or TV-out setting, install the IBP190
module.
SDVO LVDS Protocol: 1CH 18bit
SDVO Panel: 1024x768
Boot Display: CRT+LVDS
TV Standard: Off
Video Connector: Automatic
TV Format: Auto
MI935 User’s Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Integrated Peripherals
This section sets configurations for your hard disk and other integrated
peripherals. The first screen shows three main items for user to select.
Once an item selected, a submenu appears. Details follow.
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
Press Enter
Press Enter
Press Enter
ITEM HELP
OnChip IDE Device
SuperIO Device
Menu Level >
USB Device Setting
Phoenix - AwardBIOS CMOS Setup Utility
OnChip IDE Device
Enabled
Enabled
ITEM HELP
Menu Level >
IDE HDD Block Mode
IDE DMA transfer access
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
On-Chip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
SATA Mode
Auto
Auto
Auto
Auto
Enabled
Auto
Auto
Auto
Auto
IDE
LEGACY Mode Support
Enabled
Phoenix - AwardBIOS CMOS Setup Utility
SuperIO Device
ITEM HELP
Menu Level >
POWER ON Function
KB Power ON Password
Hot Key power ON
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
BUTTON ONLY
Enter
Ctrl-F1
3F8/IRQ4
2F8/IRQ3
Normal
Off
PWRON After PWR-Fail
Phoenix - AwardBIOS CMOS Setup Utility
USB Device Setting
Enabled
ITEM HELP
Menu Level >
USB 1.0 Controller
Enabled
Disabled
Disabled
USB 2.0 Controller
USB Keyboard Function
USB Mouse Function
USB Storage Function
Enabled
*** USB Mass Storage Device Boot Setting ***
32
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
IDE HDD Block Mode
This field allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive.
IDE DMA Transfer Access
This field, by default, is enabled
OnChip Secondary PCI IDE
This field, by default, is enabled
IDE Primary/Secondary Master/Slave PIO
These fields allow your system hard disk controller to work faster.
Rather than have the BIOS issue a series of commands that transfer to or
from the disk drive, PIO (Programmed Input/Output) allows the BIOS to
communicate with the controller and CPU directly.
The system supports five modes, numbered from 0 (default) to 4, which
primarily differ in timing. When Auto is selected, the BIOS will select
the best available mode.
IDE Primary/Secondary Master/Slave UDMA
These fields allow your system to improve disk I/O throughput to
33Mb/sec with the Ultra DMA/33 feature. The options are Auto and
Disabled.
SATA Mode
The setting choices for the SATA Mode are IDE, RAID and AHCI
Mode. Select [IDE] if you want to have SATA function as IDE.
Select [AHCI] for Advanced Host Controller Interface (AHCI) feature,
with improved SATA performance with native command queuing &
native hot plug. Select [RAID] to use SATA as RAID function. RAID
function is supported on the board if it uses ICH9R, but this is optional.
LEGACY Mode Support
When the Serial ATA (SATA) is set with the legacy mode enabled, then
the SATA is set to the conventional IDE mode. Legacy mode is
otherwise known as compatible mode.
Power ON Function
This field is related to how the system is powered on – such as with the
use of conventional power button, keyboard or hot keys. The default is
BUTTON ONLY.
MI935 User’s Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
KB Power ON Password
This field allows users to set the password when keyboard power on is
the mode of the Power ON function.
Hot Key Power ON
This field sets certain keys, also known as hot keys, on the keyboard that
can be used as a ‘switch’ to power on the system.
Onboard Serial Port
These fields allow you to select the onboard serial and parallel ports and
their addresses. The default values for these ports are:
Serial Port 1
Serial Port 2
3F8/IRQ4
2F8/IRQ3
UART Mode Select
This field determines the UART 2 mode in your computer. The default
value is Normal.
PWRON After PWR-Fail
This field sets the system power status whether on or off when power
returns to the system from a power failure situation.
USB 1.0 Controller
The options for this field are Enabled and Disabled. By default, this field
is set to Enabled.
USB 2.0 Controller
The options for this field are Enabled and Disabled. By default, this field
is set to Enabled. In order to use USB 2.0, necessary OS drivers must be
installed first. Please update your system to Windows 2000 SP4 or
Windows XP SP2.
USB Keyboard/Mouse/Storage Function
The options for this field are Enabled and Disabled. By default, this field
is set to Disabled.
34
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Power Management Setup
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
Enabled
S3(STR)
User Define
V/H SYNC+Blank
Yes
ITEM HELP
ACPI Function
ACPI Suspend
Menu Level >
Power Management
Video Off Method
Video Off In Suspend
Suspend Type
Stop Grant
3
Modem Use IRQ
Suspend Mode
Disabled
Disabled
Instant-Off
50.0%
HDD Power Down
Soft-Off by PWR-BTTN
CPU THRM-Throttling
Disabled
0
Resume by Alarm
Date (of Month) Alarm
Time (hh:mm:ss) Alarm
0 : 0 : 0
** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port
PCI PIRQ[A-D] #
HPET Support
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
32-bit mode
HPET Mode
ACPI Function
Enable this function to support ACPI (Advance Configuration and
Power Interface).
ACPI Suspend
The default setting of the ACPI Suspend mode is S3(STR).
Power Management
This field allows you to select the type of power saving management
modes. There are four selections for Power Management.
Min. Power Saving
Max. Power Saving
User Define
Minimum power management
Maximum power management.
Each of the ranges is from 1 min. to 1hr.
Except for HDD Power Down which ranges
from 1 min. to 15 min.
Video Off Method
This field defines the Video Off features. There are three options.
V/H SYNC + Blank
Default setting, blank the screen and turn
off vertical and horizontal scanning.
Allows BIOS to control the video display.
Writes blanks to the video buffer.
DPMS
Blank Screen
MI935 User’s Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Video Off In Suspend
When enabled, the video is off in suspend mode.
Suspend Type
The default setting for the Suspend Type field is Stop Grant.
Modem Use IRQ
This field sets the IRQ used by the Modem. By default, the setting is 3.
Suspend Mode
When enabled, and after the set time of system inactivity, all devices
except the CPU will be shut off.
HDD Power Down
When enabled, and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.
Soft-Off by PWRBTN
This field defines the power-off mode when using an ATX power
supply. The Instant Off mode allows powering off immediately upon
pressing the power button. In the Delay 4 Sec mode, the system powers
off when the power button is pressed for more than four seconds or
enters the suspend mode when pressed for less than 4 seconds.
CPU THRM-Throttling
When the system enters Doze mode, the CPU clock runs only part of the
time. You may select the percent of time that the clock runs.
Resume by Alarm
This field enables or disables the resumption of the system operation.
When enabled, the user is allowed to set the Date and Time.
Reload Global Timer Events
The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events that can
prevent the system from entering a power saving mode or can awaken
the system from such a mode. When an I/O device wants to gain the
attention of the operating system, it signals this by causing an IRQ to
occur. When the operating system is ready to respond to the request, it
interrupts itself and performs the service.
36
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
PNP/PCI Configurations
This option configures the PCI bus system. All PCI bus systems on the
system use INT#, thus all installed PCI cards must be set to this value.
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
No
PNP OS Installed
PCI Slot
Disabled
ITEM HELP
Init Display First
Reset Configuration Data
Menu Level >
Auto (ESCD)
Resources Controlled By
IRQ Resources
Press Enter
Press Enter
DMA Resources
Disabled
128
PCI/VGA Palette Snoop
**PCI Express relative items**
Maximum Payload Size
PNP OS Install
Enable the PNP OS Install option if it is supported by the
operating system installed. The default value is No.
Init Display First
The default setting is PCI Card.
Reset Configuration Data
The default value is Disabled.
Resources Controlled by
This PnP BIOS can configure all of the boot and compatible devices
with the use of a PnP operating system such as Windows 95.
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors properly.
This field allows you to set whether or not MPEG ISA/VESA VGA
cards can work with PCI/VGA. When this field is enabled, a PCI/VGA
can work with an MPEG ISA/VESA VGA card. When this field is
disabled, a PCI/VGA cannot work with an MPEG ISA/VESA card.
Maximum Payload Size
The default setting of the PCI Express Maximum Payload Size is 128.
MI935 User’s Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
PC Health Status
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
ITEM HELP
Shutdown Temperature
CPU Warning Temperature
North Bridge Temp.
CPU Temp.
System Temp.
System Fan Speed
CPU Fan Speed
Disabled
Disabled
Menu Level >
32°C/89°F
39°C/102°F
39°C/102°F
0 RPM
4440 RPM
0 RPM
Chassis Fan Speed
Vcore
12 V
1.8 V
1.24
V
12.03 V
1.92
4.99
V
V
5
V
-12V
-11.62 V
3.3 V
3.15
3.13
5.29
V
V
V
VBAT (V)
5VSB(V)
Smart Fan2 Temperature
Fan2 Tolerance Value
Smart Fan3 Temperature
Fan3 Tolerance Value
Disabled
5
Disabled
5
CPU Warning Temperature
This field allows the user to set the temperature so that when the
temperature is reached, the system sounds a warning. This function can
help prevent damage to the system that is caused by overheating.
Shutdown Temperature
This field allows the user to set the temperature by which the system
automatically shuts down once the threshold temperature is reached.
This function can help prevent damage to the system that is caused by
overheating.
Temperatures/Fan Speeds/Voltages
These fields are the parameters of the hardware monitoring function
feature of the board. The values are read-only values as monitored by the
system and show the PC health status.
38
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Frequency/Voltage Control
Phoenix - AwardBIOS CMOS Setup Utility
Frequency/Voltage Control
Disabled
Disabled
ITEM HELP
Auto Detect PCI Clk
Spread Spectrum
Menu Level >
Auto Detect PCI Clk
This field enables or disables the auto detection of the PCI clock.
Spread Spectrum
This field sets the value of the spread spectrum. The default setting is
Disabled. This field is for CE testing use only.
MI935 User’s Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Load Fail-Safe Defaults
This option allows you to load the troubleshooting default values
permanently stored in the BIOS ROM. These default settings are
non-optimal and disable all high-performance features.
Load Optimized Defaults
This option allows you to load the default values to your system
configuration. These default settings are optimal and enable all high
performance features.
Set Supervisor/User Password
These two options set the system password. Supervisor Password sets a
password that will be used to protect the system and Setup utility. User
Password sets a password that will be used exclusively on the system. To
specify a password, highlight the type you want and press <Enter>. The
Enter Password: message prompts on the screen. Type the password, up
to eight characters in length, and press <Enter>. The system confirms
your password by asking you to type it again. After setting a password,
the screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are
prompted to enter the password. A message will confirm the password to
be disabled. Once the password is disabled, the system will boot and you
can enter Setup freely.
Save & Exit Setup
This option allows you to determine whether or not to accept the
modifications. If you type “Y”, you will quit the setup utility and save all
changes into the CMOS memory. If you type “N”, you will return to
Setup utility.
Exit Without Saving
Select this option to exit the Setup utility without saving the changes you
have made in this session. Typing “Y” will quit the Setup utility without
saving the modifications. Typing “N” will return you to Setup utility.
40
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
2nd SuperIO Device
The 2nd SuperIO selection under the Integrated Peripherals will appear if
the ID394-R daughter card is used on the motherboard.
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
Press Enter
Press Enter
Press Enter
Press Enter
ITEM HELP
OnChip IDE Device
SuperIO Device
2nd SuperIO Device
USB Device Setting
Menu Level >
Phoenix - AwardBIOS CMOS Setup Utility
2nd SuperIO Device
230h
IRQ5
ITEM HELP
Menu Level >
Onboard Serial Port 3
Serial Port 3 Use IRQ
Onboard Serial Port 4
Serial Port 4 Use IRQ
Onboard Serial Port 5
Serial Port 5 Use IRQ
Onboard Serial Port 6
Serial Port 6 Use IRQ
238h
IRQ7
Disabled
IRQ10
Disabled
IRQ11
Onboard Serial Port
These fields allow you to select the onboard serial and parallel ports and
their addresses. The default values for these ports are:
Serial Port 3
Serial Port 4
Serial Port 5
Serial Port 6
230/IRQ5
238/IRQ7
Disabled/IRQ10
Disabled/IRQ11
MI935 User’s Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
This page is intentionally left blank.
42
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
Drivers Installation
This section describes the installation procedures for software and
drivers under the Windows 2000 and Windows XP. The software and
drivers are included with the board. If you find the items missing, please
contact the vendor where you made the purchase. The contents of this
section include the following:
IMPORTANT NOTES:
1. After installing your Windows operating system (Windows 2000/XP),
you must install first the Intel Chipset Software Installation Utility
before proceeding with the drivers installation.
2. How to create an AHCI driver disk, when your board supports the
RAID/AHC function:
1.Put an empty disc into your floppy disk drive
2.Execute the f6flpy32.exe that is in the Driver CD you have received.
The path is 8.1A\Intel\Q35\Raid\
MI935 User’s Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
Intel Chipset Software Installation Utility
The Intel® Chipset Drivers should be installed first before the software
drivers to enable Plug & Play INF support for Intel chipset components.
Follow the instructions below to complete the installation under
Windows 2000/XP/Vista. (Before installed Intel Chipset Software
Installation Utility,Please update your system to Windows 2000 SP4 or
Windows XP SP1A)
1. Insert the DVD that comes with the board. Click Intel Chipsets and
then Intel(R) Bearlake Chipset Family Drivers.
2. Click Intel(R) Chipset Software Installation Utility.
3. When the Welcome screen appears, click Next to continue.
44
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
4. Click Yes to accept the software license agreement and proceed with
the installation process.
5. On the Readme Information screen, click Next to continue the
installation.
6. When the Setup Progress screen appears, click Next to continue.
7. The Setup process is now complete. Click Finish then restart the
computer and for changes to take effect.
MI935 User’s Manual
45
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
Intel Graphics Driver Installation
To install the Graphics drivers, follow the steps below to proceed with
the installation.
1. Insert the DVD that comes with the board. Click Intel Chipsets and
then Intel(R) Bearlake Chipset Family Drivers.
2. Click Intel(R) Bearlake Chipset Family Graphics Driver.
3. When the Welcome screen appears, click Next to continue.
4. Click Yes to accept the software license agreement and proceed with
the installation process.
5. On Readme File Information screen, click Next to continue.
6. On Setup Progress screen, click Next to continue the installation.
7. The Setup process is now complete. Click Finish to restart the
computer and for changes to take effect.
46
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
Realtek HD Code Audio Driver Installation
Follow the steps below to install the Realtek High Definition Codec
Audio Driver.
1. Insert the DVD that comes with the board. Click Intel Chipsets and
then Intel(R) Bearlake Chipset Family Drivers.
2. Click Realtek High Definition Codec Audio Driver.
3. When the Welcome screen appears, click Next to continue.
4. The Setup process is now complete. Restart the computer when
prompted for changes to take effect.
MI935 User’s Manual
47
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
LAN Drivers Installation
Follow the steps below to start installing the Intel 82566DM or Intel
82562V drivers.
1. Insert the DVD that comes with the board. Click Intel Chipsets and
then Intel(R) Bearlake Chipset Family Drivers.
2. Click Intel(R) PRO LAN Network Drivers.
3. On the next screen, click Install Drivers to start the drivers
installation.
4. When the Welcome screen appears, click Next to continue.
5. In the License Agreement screen, click I accept the terms in license
agreement and Next to accept the software license agreement and
proceed with the installation process.
6. When the Setup Options appears, click Install Drivers only and Next
to continue.
7. When the Ready to Install the Program screen appears, click Install to
continue.
8. The Setup process is now complete (InstallShield Wizard Completed).
Click Finish to restart the computer and for changes to take effect.
48
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
Follow the steps below to install the Marvell Gigabit LAN drivers.
1. Insert the CD that comes with the motherboard. Click LAN Card and
then Marvell LAN Controller Drivers.
2. Click Next when the InstallShield Wizard welcome screen appears.
3. Click Next to agree with the license agreement.
4. Click Next when the Readme Information screen appears to proceed
with the drives installation process.
5. When the Installation is complete, click Finish for the changes to take
effect.
MI935 User’s Manual
49
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
Follow the steps below to use the wake up function by Intel 82566DM or
Intel 82562V.
1. The BIOS Setup item “Wake-Up by PCI card” has to be set as
[Enabled] .
2. Go to the Device Manager under Windows and select Network
adapters. The following window will appear (Intel(R) 82566DM Gigabit
Network Connection Properties). Click Power Management and select
Wake on Magic Packet from power off states .
3. Turn off computer .
50
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
Follow the steps below to install the Marvell Gigabit LAN drivers.
1. Insert the DVD that comes with the board. Click LAN Card and then
Marvell LAN Controller Driver.
2. Click Next when the InstallShield Wizard welcome screen appears.
3. Click Next to agree with the license agreement.
4. Click Install when the Ready to Install the Program screen appears to
proceed with the drives installation process.
5. When the Installation is complete, click Finish for the changes to take
effect.
6. To use the wake up function by Marvell Gigabit LAN, go to the
Device Manager under Windows and select Network adapters. The
following window will appear (Generic Marvell Yukon Chipset based
Ethernet Controller Properties). Click Advanced and select Wake From
Shutdown. In the Value field on the right, select On.
7. Then, also in the Advanced section, click on Wake Up Capabilities. In
the Value field on the right, select Magic Packet, then click OK.
8. Turn off computer.
MI935 User’s Manual
51
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Appendix
A. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port
addresses that also becomes the identity of the device. The following
table lists the I/O port addresses used.
Address
Device Description
DMA Controller #1
Interrupt Controller #1
Timer
Keyboard Controller
Real Time Clock, NMI
DMA Page Register
Interrupt Controller #2
DMA Controller #2
Clear Math Coprocessor Busy Signal
Reset Math Coprocessor
IDE Interface
Parallel Port #2(LPT2)
Serial Port #2(COM2)
Graphics adapter Controller
Parallel Port #1(LPT1)
Network Ports
000h - 01Fh
020h - 03Fh
040h - 05Fh
060h - 06Fh
070h - 07Fh
080h - 09Fh
0A0h - 0BFh
0C0h - 0DFh
0F0h
0F1h
1F0h - 1F7h
278h - 27Fh
2F8h - 2FFh
2B0h - 2DFh
378h - 3FFh
360h - 36Fh
3B0h - 3BFh
3C0h - 3CFh
3D0h - 3DFh
3F0h - 3F7h
3F8h - 3FFh
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy Disk Controller
Serial Port #1(COM1)
52
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
B. Interrupt Request Lines (IRQ)
Peripheral devices use interrupt request lines to notify CPU for the
service required. The following table shows the IRQ used by the devices
on board.
Level
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
Function
System Timer Output
Keyboard
Interrupt Cascade
Serial Port #2
Serial Port #1
Reserved
Floppy Disk Controller
Parallel Port #1
Real Time Clock
Reserved
Reserved
Reserved
PS/2 Mouse
80287
Primary IDE
Secondary IDE
MI935 User’s Manual
53
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
C. Watchdog Timer Configuration
The WDT is used to generate a variety of output signals after a user
programmable count. The WDT is suitable for use in the prevention of
system lock-up, such as when software becomes trapped in a deadlock.
Under these sorts of circumstances, the timer will count to zero and the
selected outputs will be driven. Under normal circumstance, the user
will restart the WDT at regular intervals before the timer counts to zero.
SAMPLE CODE:
//=======================================================================
//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//=======================================================================
====
#include <stdio.h>
#include <stdlib.h>
#include "W627EHF.H"
//=======================================================================
====
int main (int argc, char *argv[]);
void copyright(void);
void EnableWDT(int);
void DisableWDT(void);
//=======================================================================
====
int main (int argc, char *argv[])
{
unsigned char bBuf;
unsigned char bTime;
char **endptr;
copyright();
if (argc != 2)
{
printf(" Parameter incorrect!!\n");
return 1;
}
if (Init_W627EHF() == 0)
{
printf(" Winbond 83627HF is not detected, program abort.\n");
return 1;
}
bTime = strtol (argv[1], endptr, 10);
54
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
printf("System will reset after %d seconds\n", bTime);
EnableWDT(bTime);
return 0;
}
//=======================================================================
void copyright(void)
{
printf("\n======== Winbond 83627EHF Watch Timer Tester (AUTO DETECT)
========\n"\
"
"
"
Usage : W627E_WD reset_time\n"\
Ex : W627E_WD 3 => reset system after 3 second\n"\
W627E_WD 0 => disable watch dog timer\n");
}
//=======================================================================
void EnableWDT(int interval)
{
unsigned char bBuf;
bBuf = Get_W627EHF_Reg( 0x2D);
bBuf &= (!0x01);
Set_W627EHF_Reg( 0x2D, bBuf);
//Enable WDTO
Set_W627EHF_LD( 0x08);
Set_W627EHF_Reg( 0x30, 0x01);
//switch to logic device 8
//enable timer
bBuf = Get_W627EHF_Reg( 0xF5);
bBuf &= (!0x08);
Set_W627EHF_Reg( 0xF5, bBuf);
//count mode is second
Set_W627EHF_Reg( 0xF6, interval);
//set timer
}
//=======================================================================
void DisableWDT(void)
{
Set_W627EHF_LD(0x08);
Set_W627EHF_Reg(0xF6, 0x00);
Set_W627EHF_Reg(0x30, 0x00);
//switch to logic device 8
//clear watchdog timer
//watchdog disabled
}
//=======================================================================
MI935 User’s Manual
55
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
//=======================================================================
//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//=======================================================================
====
#include "W627EHF.H"
#include <dos.h>
//=======================================================================
====
unsigned int W627EHF_BASE;
void Unlock_W627EHF (void);
void Lock_W627EHF (void);
//=======================================================================
unsigned int Init_W627EHF(void)
{
unsigned int result;
unsigned char ucDid;
W627EHF_BASE = 0x2E;
result = W627EHF_BASE;
ucDid = Get_W627EHF_Reg(0x20);
if (ucDid == 0x88)
{
goto Init_Finish;
}
W627EHF_BASE = 0x4E;
result = W627EHF_BASE;
ucDid = Get_W627EHF_Reg(0x20);
if (ucDid == 0x88)
{
goto Init_Finish;
}
W627EHF_BASE = 0x00;
result = W627EHF_BASE;
Init_Finish:
return (result);
}
//=======================================================================
void Unlock_W627EHF (void)
{
outportb(W627EHF_INDEX_PORT, W627EHF_UNLOCK);
outportb(W627EHF_INDEX_PORT, W627EHF_UNLOCK);
}
//=======================================================================
====
void Lock_W627EHF (void)
{
outportb(W627EHF_INDEX_PORT, W627EHF_LOCK);
}
//=======================================================================
void Set_W627EHF_LD( unsigned char LD)
{
Unlock_W627EHF();
outportb(W627EHF_INDEX_PORT, W627EHF_REG_LD);
outportb(W627EHF_DATA_PORT, LD);
56
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Lock_W627EHF();
}
//=======================================================================
void Set_W627EHF_Reg( unsigned char REG, unsigned char DATA)
{
Unlock_W627EHF();
outportb(W627EHF_INDEX_PORT, REG);
outportb(W627EHF_DATA_PORT, DATA);
Lock_W627EHF();
}
//=======================================================================
unsigned char Get_W627EHF_Reg(unsigned char REG)
{
unsigned char Result;
Unlock_W627EHF();
outportb(W627EHF_INDEX_PORT, REG);
Result = inportb(W627EHF_DATA_PORT);
Lock_W627EHF();
return Result;
}
//=======================================================================
//=======================================================================
//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//=======================================================================
#ifndef __W627EHF_H
#define __W627EHF_H
1
//=======================================================================
#define
#define
W627EHF_INDEX_PORT
W627EHF_DATA_PORT
(W627EHF_BASE)
(W627EHF_BASE+1)
//=======================================================================
#define W627EHF_REG_LD 0x07
//=======================================================================
#define W627EHF_UNLOCK
#define W627EHF_LOCK
0x87
0xAA
//=======================================================================
unsigned int Init_W627EHF(void);
void Set_W627EHF_LD( unsigned char);
void Set_W627EHF_Reg( unsigned char, unsigned char);
unsigned char Get_W627EHF_Reg( unsigned char);
//=======================================================================
#endif
//__W627EHF_H
MI935 User’s Manual
57
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
File of the Main.cpp
//=====================================================================
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//=====================================================================
#include <dos.h>
#include <conio.h>
#include <stdio.h>
#include <stdlib.h>
#include "W627HF.H"
//=====================================================================
void ClrKbBuf(void);
int main (int argc, char *argv[]);
//=====================================================================
int main (int argc, char *argv[])
{
unsigned char ucDO = 0;
unsigned char ucDI;
unsigned char ucBuf;
//data for digital output
//data for digital input
Set_W627HF_LD( 0x07);
//switch to logic device 7
//clear
Set_W627HF_Reg(0xF1, 0x00);
ucDI = Get_W627HF_Reg(0xF1) & 0x0F;
ClrKbBuf();
while(1)
{
ucDO++;
Set_W627HF_Reg(0xF1, ((ucDO & 0x0F) << 4));
ucBuf = Get_W627HF_Reg(0xF1) & 0x0F;
if (ucBuf != ucDI)
{
ucDI = ucBuf;
printf("Digital I/O Input Changed. Current Data is 0x%X\n",ucDI);
}
if (kbhit())
{
getch();
break;
}
delay(500);
}
return 0;
}
//=====================================================================
void ClrKbBuf(void)
{
while(kbhit())
{
getch();
}
}
//---------------------------------------------------------------------------
58
MI935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
|