®
Intel IXP43X Product Line of
Network Processors
Hardware Design Guidelines
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
1.0 Introduction..............................................................................................................9
Content Overview................................................................................................9
Related Documentation...................................................................................... 10
2.0 System Architecture ................................................................................................ 15
System Architecture Description.......................................................................... 15
3.0 General Hardware Design Considerations................................................................ 17
DDRII/I SDRAM Interface................................................................................... 18
3.2.1 Signal Interface ..................................................................................... 19
3.2.2 DDRII/I SDRAM Initialization ................................................................... 20
3.3.1 Signal Interface ..................................................................................... 21
3.3.2 Reset Configuration Straps ...................................................................... 22
3.3.3 8-Bit Device Interface............................................................................. 24
3.3.4 16-Bit Device Interface ........................................................................... 25
3.3.5 Flash Interface....................................................................................... 26
3.4.1 Signal Interface ..................................................................................... 27
3.5.1 Signal Interface MII................................................................................ 29
3.5.2 Device Connection, MII ........................................................................... 30
GPIO Interface.................................................................................................. 31
3.6.1 Signal Interface ..................................................................................... 32
3.6.2 Design Notes ......................................................................................... 32
3.7.1 Signal Interface ..................................................................................... 33
3.8.1 Signal Interface ..................................................................................... 36
3.8.2 Device Connection.................................................................................. 40
HSS Interface................................................................................................... 40
3.9.1 Signal Interface ..................................................................................... 41
3.9.2 Device Connection.................................................................................. 41
3.10 SSP Interface ................................................................................................... 42
3.10.1 Signal Interface ..................................................................................... 43
3.10.2 Device Connection.................................................................................. 43
3.11 PCI Interface .................................................................................................... 44
3.11.1 Signal Interface ..................................................................................... 45
3.11.2 PCI Interface Block Diagram .................................................................... 46
3.11.3 PCI Option Interface............................................................................... 47
3.11.4 Design Notes ......................................................................................... 49
3.12 JTAG Interface.................................................................................................. 49
3.12.1 Signal Interface ..................................................................................... 50
3.13 Input System Clock ........................................................................................... 50
3.13.1 Clock Signals......................................................................................... 50
3.13.2 Clock Oscillator ...................................................................................... 50
3.13.3 Recommendations for Crystal Selection..................................................... 51
®
Intel IXP43X Product Line of Network Processors
April 2007
Document Number: 316844; Revision: 001US
HDG
3
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
3.14 Power ..............................................................................................................52
3.14.2 VCC Decoupling......................................................................................53
3.14.3 VCC33 Decoupling ..................................................................................53
3.14.4 VCCDDR Decoupling................................................................................53
3.14.5 Power Sequence.....................................................................................53
3.14.6 Reset Timing..........................................................................................53
4.0 General PCB Guide ...................................................................................................55
5.0 General Layout and Routing Guide...........................................................................59
Overview..........................................................................................................59
5.2.1 General Component Spacing ....................................................................60
5.2.2 Clock Signal Considerations......................................................................62
5.2.3 MII Signal Considerations ........................................................................63
5.2.4 USB V2.0 Considerations .........................................................................63
5.2.5 Crosstalk...............................................................................................63
5.2.6 EMI Design Considerations.......................................................................64
5.2.7 Trace Impedance....................................................................................64
5.2.8 Power and Ground Plane..........................................................................64
6.0 PCI Interface Design Considerations........................................................................66
Electrical Interface.............................................................................................66
6.3.1 Trace Length Limits.................................................................................68
6.3.2 Routing Guidelines..................................................................................69
6.3.3 Signal Loading........................................................................................69
7.0 DDRII / DDRI SDRAM ..............................................................................................70
Introduction......................................................................................................70
DDRII OCD Pin Requirements..............................................................................75
7.3.1 Signal-Timing Analysis ............................................................................75
7.3.2 Timing Relationships ...............................................................................78
7.3.3 Routing Guidelines..................................................................................81
7.3.3.2 Data and Control Groups............................................................82
9
Intel IXP435 Network Processor Block Diagram ..........................................................13
UART Interface Example............................................................................................28
USB RCOMP and ICOMP Pin Requirement.....................................................................35
USB Host Down Stream Interface Example...................................................................35
10 UTOPIA Interface Example.........................................................................................40
®
Intel IXP43X Product Line of Network Processors
HDG
4
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
11 HSS Interface Example............................................................................................. 42
12 Serial Flash and SSP Port (SPI) Interface Example........................................................ 44
13 PCI Interface........................................................................................................... 47
14 Clock Oscillator Interface Example.............................................................................. 51
15 Recommended circuit design on PCB for crystal oscillator .............................................. 52
16 Component Placement on a PCB................................................................................. 56
17 8-Layer Stackup ...................................................................................................... 58
18 6-Layer Stackup ...................................................................................................... 58
19 Signal Changing Reference Planes.............................................................................. 60
20 Good Design Practice for VIA Hole Placement............................................................... 61
21 Poor Design Practice for VIA Placement....................................................................... 61
22 Pad-to-Pad Clearance of Passive Components to a PGA or BGA....................................... 62
23 PCI Address/Data Topology ....................................................................................... 67
24 PCI Clock Topology .................................................................................................. 68
25 Processor-DDRII/I SDRAM Interface ........................................................................... 72
26 DDRII/DDRI RCOMP Pin External Resistor Requirements ............................................... 74
27 DDRII OCD Pin Requirements .................................................................................... 75
28 DDR Clock Timing Waveform ..................................................................................... 75
29 DDR SDRAM Write Timings........................................................................................ 76
30 DDR SDRAM Read Timings ........................................................................................ 76
31 DDR - Write Preamble/Postamble Duration.................................................................. 77
32 DDRII Clock Simulation Results: CK Signals................................................................. 82
33 DDRII Data and Control Simulation Results: DQ and DQS signals ................................... 83
34 DDRII Command Simulation Results: ADDRESS signals................................................. 84
Soft Fusible Features................................................................................................ 17
DDRII/I SDRAM Interface Pin Description.................................................................... 19
Boot/Reset Strapping Configuration............................................................................ 22
Setting Intel XScale Processor Operation Speed ......................................................... 24
10 MII NPE C Signal Recommendations ........................................................................... 29
12 GPIO Signal Recommendations .................................................................................. 32
13 USB Host Signal Recommendations ............................................................................ 33
14 UTOPIA Level 2/MII_A .............................................................................................. 36
15 High-Speed, Serial Interface 0................................................................................... 41
16 Synchronous Serial Peripheral Port Interface................................................................ 43
17 PCI Controller.......................................................................................................... 45
18 PCI Host/Option Interface Pin Description.................................................................... 47
19 Synchronous Serial Peripheral Port Interface................................................................ 50
20 Clock Signals........................................................................................................... 50
21 Power Supply .......................................................................................................... 52
22 PCI Address/Data Routing Guidelines.......................................................................... 67
23 PCI Clock Routing Guidelines ..................................................................................... 68
24 DDRII/I Signal Groups.............................................................................................. 71
25 Supported DDRI 32-bit SDRAM Configurations ............................................................. 73
26 Supported DDRII 32-bit SDRAM Configurations............................................................ 73
27 Supported DDRI 16-bit SDRAM Configurations ............................................................. 73
28 Supported DDRII 16-bit SDRAM Configurations............................................................ 74
®
Intel IXP43X Product Line of Network Processors
April 2007
Document Number: 316844; Revision: 001US
HDG
5
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
29 DDR Clock Timings ...................................................................................................75
30 DDRII-400 MHz Interface -- Signal Timings..................................................................77
31 DDR II/I SDRAM Interface -- Signal Timings.................................................................78
32 Timing Relationships.................................................................................................79
33 Signal Package Lengths.............................................................................................79
34 Clock Signal Group Routing Guidelines ........................................................................82
35 DDRII Data and Control Signal Group Routing Guidelines...............................................83
36 DDRII Command Signal Group Routing Guidelines ........................................................84
®
Intel IXP43X Product Line of Network Processors
HDG
6
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Revision History
Date
Revision
Description
April 2007
001
Initial release
§ §
®
Intel IXP43X Product Line of Network Processors
April 2007
Document Number: 316844; Revision: 001US
HDG
7
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
®
Intel IXP43X Product Line of Network Processors
HDG
8
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
1.0
Introduction
This design guide provides recommendations for hardware and system designers who
®
are developing with the Intel IXP43X Product Line of Network Processors. This
®
document should be used in conjunction with the Intel IXP43X Product Line of
®
Network Processors Datasheet and sample schematics provided for the Intel IXP435
Multi-Service Residential Gateway Reference Platform.
Design recommendations are necessary to meet the timing and signal quality
specifications. The guidelines recommended in this document are based on experience
®
and simulation work done at Intel while developing the Intel IXP435 Multi-Service
Residential Gateway Reference Platform. These recommendations are subject to
change.
Note:
This document discusses all features supported on the IXP43X product line of network
processors. A subset of these features is supported by certain processors in the IXP43X
®
®
network processors, such as the Intel IXP432 Network Processor. Refer to the Intel
IXP43X Product Line of Network Processors Datasheet for detailed information on
various features listed by processor.
1.1
Content Overview
Chapter Name
Description
Conventions used in this manual and related documentation
System architectural block diagram and system memory map
Chapter 2.0, “System Architecture”
Graphical representation of most common peripheral interfaces
General PCB design practice and layer stack-up description
Chapter 4.0, “General PCB Guide”
More specific layout and routing recommendations for board
designers
Considerations”
Board-design recommendations when implementing PCI
interface
Board-design recommendations when implementing
DDRII/I memory interface
Chapter 7.0, “DDRII / DDRI SDRAM”
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
9
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
1.2
Related Documentation
The reader of this design guide should also be familiar with the material and concept
presented in the following documents:
Title
Document #
®
Intel IXP43X Product Line of Network Processors Datasheet
316842
®
Intel IXP43X Product Line of Network Processors Developer’s
316843
316845
Manual
®
Intel IXP43X Product Line of Network Processors: Migrating from
®
the Intel IXP42X Product Line
®
Intel IXP400 Software Programmer’s Guide
252539
273795
273473
__
®
Intel IXP400 Software Specification Update
®
Intel XScale™ Core Developer’s Manual
®
Intel StrataFlash Embedded Memory (P30) Application Note
®
Intel XScale Microarchitecture Technical Summary
—
Double Data Rate (DDR) SDRAM Specification, 2004; JEDEC Solid
State Technology Association
JESD79D
IEEE 802.3 Specification
N/A
N/A
N/A
N/A
PCI Local Bus Specification, Rev. 2.2
Universal Serial Bus Specification, Revision 2.0
UTOPIA Level 2 Specification, Revision 1.0
1.3
Table 1 lists the acronyms and abbreviations used in this guide.
Table 1.
List of Acronyms and Abbreviations (Sheet 1 of 2)
Term
Explanation
AHB
APB
ATM
DDR
EMI
GPIO
HSS
IP
Advanced High-Performance Bus
Advanced Peripheral Bus
Asynchronous Transfer Mode
Double Data Rate
Electro-Magnetic Interference
General Purpose Input/Output
High Speed Serial
Internet Protocol
ISA
LAN
MII
Instruction Set Architecture
Local Area Network
Media-Independent Interface
Network Processor Engine
Printed Circuit Board
NPE
PCB
PCI
Peripheral Component Interface
Physical Layer Interface
Phase-Locked Loop
PHY
PLL
®
Intel IXP43X Product Line of Network Processors
HDG
10
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Table 1.
List of Acronyms and Abbreviations (Sheet 2 of 2)
Term
Explanation
PMU
SME
SSP
Performance Monitoring Unit
Small-to-Medium Enterprise
Synchronous Serial Protocol
UART
USB
VTT
Universal Asynchronous Receiver-Transmitter
Universal Serial Bus
Termination Voltage Supply
1.4
Overview
®
The Intel IXP43X Product Line of Network Processors is a highly integrated device,
capable of interfacing with most common industry standard peripherals, required for
high-performance control applications.
Note:
This document discusses all features supported on the IXP43X network processors.
®
Refer to the Intel IXP43X Product Line of Network Processors Datasheet for details on
feature support listed by processor.
Some of the key features of the IXP43X network processors, when used as a
single-chip solution for embedded applications are as follows:
®
®
*
• Intel XScale Processor (compliant with Intel StrongARM architecture) up to 667
MHz
• 32-bit PCI interface Master/Target 33 MHz
• Two Universal Serial Bus (USB) V2.0 Host Controller
• DDRI-266 SDRAM or DDRII-400 SDRAM—
— Support for 16 MB, minimum for DDR II/I, 32 MB minimum for DDRII-400;
1 GB, maximum for DDR II/I, 512 MBs maximum for DDRII-400
— User-enabled ECC.
• 16bit Data / 24bit Address Expansion Bus Interface
• One UART interface
• Two NPEs
• UTOPIA Level 2 Interface
• Synchronous Serial Port Interface (SSP)
• One High-Speed Serial Port Interfaces (HSS)
Note 1
• Network interfaces that can be configured in the following manner:
— Two MII interfaces
— One MII interface + 1 UTOPIA Level 2 interface
Note 1
• MII interfaces are:
— 802.3 MII interfaces
— Single MDIO interface to control the MII interfaces
Note 1
• UTOPIA Level 2 Interface is:
— Eight-bit interface
— Up to 33-MHz clock speed
— Five transmit and five receive address lines
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
11
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
• 16 GPIO (General Purpose Input Output)
• Packaging
— 460-pin PBGA
— 31 mm by 31 mm
— Commercial temperature (0° to 70° C)
— Lead free support
®
Refer to the Intel IXP43X Product Line of Network Processors Datasheet for complete
feature list and block diagram description.
Note:
1. This feature requires Intel-supplied software. To determine if this feature is enabled
®
in a particular software release, refer to the Intel IXP400 Software Programmer’s
Guide.
A block diagram of all major internal hardware components of IXP43X network
processors is shown in Figure 1. The illustration also shows how the components
interface with each other through the various bus interfaces such as the North AHB,
South AHB, and APB.
®
Intel IXP43X Product Line of Network Processors
HDG
12
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
®
Figure 1.
Intel IXP435 Network Processor Block Diagram
HSS
UTOPIA 2/ MII
NPE A
NPE C
North AHB133. 32 MHz x32bits
MII
AES/ 3DES/
DES/
SHA/ MD-5
North AHB
Arbiter
SSP
High Speed
UART
921 Kbaud
16 GPIO
GPIO
16/ 32 BITS
+ ECC
AHB
Slave /
APB
Interrupt
Controller
DDR 266 /
DDRII 400
DDRII/ I MEMORY
CONTROLLER
UNIT
QUEUE
MANAGER
AHB/ AHB
BRIDGE
Master
BRIDGE
266/ 400
IBPMU
Timers
South AHB133. 32 MHz x32 bits
South AHB
Arbiter
USB Port
USB Port
HOST
CONTROLLER
VERSION2.0
EXPANSION
BUS Controller
8/16 bit 80MHz
PCI
HOST
CONTROLLER
VERSION 2.0
CONTROLLER
32 bit 33 MHz
XScale Processor
32 KB I - CACHE
32KB D - CACHE
UTMI
UTMI
2KB MINI D- CACHE
266/400/533/667 MHz
2.0 PHY
2. 0 PHY
Bus Arbiters
Slave Only
Master on South AHB
Master on North AHB
AHB Slave APB Master
/
®
Note:
Figure 1 shows the Intel IXP435 Network Processor. For details on feature and SKU
®
support listed by processor, see the Intel IXP43X Product Line of Network Processors
Datasheet.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
13
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
1.5
Typical Applications
• SOHO-Small Business/Residential
• Modular Router
• Wireless Gateway(802.11a/b/g)
• Network-Attached Storage
• Wired/Wireless RFID Readers
• Digital Media Adapter
• Digital Media Player
• VoIP Router
• Video Phone
• Secure Gateway/Router
• Network Printer
• Wireless Media Gateway
• IP Set Top box
§ §
®
Intel IXP43X Product Line of Network Processors
HDG
14
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
2.0
System Architecture
2.1
System Architecture Description
®
The Intel IXP43X Product Line of Network Processors is a multifunction processor that
®
integrates the Intel XScale Processor (ARM* architecture compliant) with highly
integrated peripheral controllers and network processor engines.
The processor is a highly integrated design, manufactured with Intel’s 0.13-µm
production semiconductor process technology. This process technology, along with
numerous, dedicated function peripheral interfaces and many features with the Intel
XScale processor, addresses the needs of many system applications and helps reduce
system costs. The processors can be configured to meet many system application and
Figure 2 illustrates one of the many applications for which the IXP43X network
®
processors can be implemented. For detailed functional description, see the Intel
IXP43X Product Line of Network Processors Developer’s Manual.
2.2
System Memory Map
®
Refer to the Intel IXP43X Product Line of Network Processors Developer’s Manual for
a complete memory map and register description of each individual module.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
15
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
®
Figure 2.
Example: Intel IXP43X Product Line of Network Processors System Block
Diagram
JTAG
Header
Flash
32 Mbyte
CB[7:0]
D[31:0]
BA[1:0]
A[13:0]
DDRII/I
CS_N0
SDRAM
Max 1 Gbyte
D[15:0]
A[23:0]
RAS, CAS, WE, CS,CLK
Board
Configuration
Reset Logic
SSP
SLIC/CODEC or
T1/E1/J1 Framer
Intel® IXP43X Product
Line of Network
Processors
HSS 0
LCD/LED
Diagnostics
Display
Buff
SSP
CODEC or
A/D
xDSL
RS232
Serial Port 0
UTOPIA Level 2
DB9
PLL
OSC
Clock Buffer
RJ45
Port 0
10/100
PHYs
2-MII
Ethernet
Clocks
PCI
Clock
Up to 2 Ports
RJ45
Port 1
5 V
USB Host
Connector
USB v2.0
USB v2.0
3.3 V
2.5/1.8 V
1.3 V
Power Supply
USB Host
Connector
Transparent PCI Bridge
cPCI Bus
B4835-003
§ §
®
Intel IXP43X Product Line of Network Processors
HDG
16
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
3.0
General Hardware Design Considerations
This chapter contains information for implementing and interfacing with major
®
hardware blocks of the Intel IXP43X Product Line of Network Processors. Such blocks
include DDRII/I SDRAM, Flash, Ethernet PHYs, UART and other peripherals interfaces.
Signal definition tables list resistor recommendations for pull-ups and pull-downs.
Features disabled by a specific part number, do not require pull-ups or pull-downs.
Therefore, all pins can be left unconnected. Features enabled by a specific part number
and required to be Soft Fuse-disabled, only require pull-ups or pull-downs in the
clock-input signals. Other conditions can require pull-up or pull-down resistors for
configuration purposes at power on or reset. In the same way, open-drain outputs must
be pulled high.
Warning:
With the exception of USB_V5REF all other I/O pins of the IXP43X network processors
are not 5.0-V tolerant.
Table 2 gives the legend for interpreting the Type field used in the signal-definition
tables that are covered in this chapter.
Table 2.
Signal Type Definitions
Symbol
Description
Input pin only
I
O
Output pin only
Pin can be an input or output
Open-drain pin
Tri-State pin
I/O
OD
TRI
PWR
GND
Power pin
Ground pin
3.1
Soft Fusible Features
Soft Fuse Enable/Disable is a method to enable or disable features in hardware,
virtually disconnecting the hardware modules from the processor.
Some of the features offered in the IXP43X product line of network processors can be
Soft Fuse Enabled/Disabled during boot. It is recommended that if a feature is not used
in the design, the feature be soft disabled. This helps reduce power and maintain the
part running at a cooler temperature. When Soft Fuse Disabled, a pull-up resistor must
be connected to each clock input pins of the disabled feature interface. All other signals
can be left unconnected.
Soft Fuse Enable/Disable can be done by writing to EXP_UNIT_FUSE_RESET register.
®
For more information refer to the Intel IXP43X Product Line of Network Processors
Developer’s Manual and review the register description.
Table 3.
Soft Fusible Features (Sheet 1 of 2)
Name
Description
The complete bus must be enabled or disable.
PCI
HSS0
Can only be disable as a pair.
while enabling UTOPIA, MACs on NPE A is disabled.
while enabling MACs on NPE A, UTOPIA is disabled.
UTOPIA
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
17
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Table 3.
Soft Fusible Features (Sheet 2 of 2)
Name
Description
ETHERNET
USB Host
DDR ECC
Can enable MII MACs. Enable of MACs can be separately done per each NPE.
Each USB can be Enable separately.
ECC can be enabled or disabled separately from the rest of the DDR interface.
3.2
DDRII/I SDRAM Interface
The IXP43X network processors support unbuffered, DDRI-266 or DDRII-400 SDRAM
technology, capable of addressing two memory banks (one bank per CS). Each bank
can be configured to support 32/64/128/256/512-Mbyte for a total combined memory
support of 1 Gbyte.
The IXP43X network processors integrate a high-performance, multi-ported Memory
Controller Unit (MCU) to provide a direct interface with its local memory subsystem.
The MCU supports:
• DDR II/I or DDRII-400 SDRAM
• 128/256/512-Mbit, 1-Gbit DDRI SDRAM technology support
• Supports 256/512-Mbit technologies for the DDRII-400
• Only unbuffered DRAM support (No registered DRAM support)
• Dedicated port for Intel XScale processor to the DDRII/DDRI SDRAM
• Between 32 MBs and 1-GB of 32-bit DDRI SDRAM
• Between 64MBs and 512 MBs of 32-bit DDRII SDRAM
• 16MB for 16-bit memory systems for DDRI SDRAM (non-ECC) supporting 128-Mbit
technology only
• 32MB for 16-bit memory systems for DDRII SDRAM (non-ECC) supporting 256-Mbit
technology only
• Single-bit error correction, multi-bit detection support (ECC)
• 32-bit, 40-bit wide memory interfaces (non-ECC and ECC support), and 16-bit wide
memory interfaces (non-ECC)
The DDRII/DDRI SDRAM interface provides a direct connection to a high-bandwidth
and reliable memory subsystem. The DDRII/DDRI SDRAM interface is a 16 or
32-bit-wide data path.
The device supports non-ECC and ECC for error correction, which can be enable or
disable by software as required. Banks have a bus width of 32 bits for non ECC or
40 bits for ECC enable (32-bit data + 8-bit ECC).
An 8-bit Error Correction Code (ECC) across each 32-bit word improves system
reliability. It is important to note that ECC is also referred to as CB in many DIMM
specifications. The pins on the IXP43X network processors are called
DDR_CB[7:0]. ECC is only implemented in the 32-bit mode of operation, while the
algorithm used to generate the 8-bit ECC is implemented over 64-bit.
The ECC circuitry is designed to operate always on a 64-bit data and when operating in
32-bit mode, the upper 32 bits are driven to zeros internally. To summarize the impact
to the customer, the full 8 bits of ECC is stored and read from a memory array for the
ECC logic to work. An 8-bit-wide memory is used when implementing ECC.
®
Intel IXP43X Product Line of Network Processors
HDG
18
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
The memory controller only corrects single bit ECC errors on read cycles. The ECC is
stored into the DDRII/DDRI SDRAM array along with the data and is checked when the
data is read. If the code is incorrect, the MCU corrects the data before reaching the
initiator of the read. ECC error scrubbing is done with software. User-defined fault
correction software is responsible for The value written back into the memory location
contains the 32-bit word with the modified byte and the new ECC value.
®
General DDRII/I SDRAM routing guidelines can be found in Section 7.3.3, “Routing
Guidelines” on page 82. For more detailed information, see the PC266 and PC400 DDR
SDRAM specification.
3.2.1
Signal Interface
Table 4.
DDRII/I SDRAM Interface Pin Description (Sheet 1 of 2)
VTT
Terminatio
n
Type
Field
Name
Device-Pin Connection
Description
Connect a pair of differential clock
signals to every device; When
using both banks, daisy chain
devices with same data bit
sequence.
DDRII/I SDRAM Clock Out — Provides the
positive differential clocks to the external
SDRAM memory subsystem.
D_CK[2:0] /
DDR_CK[2:0]
O
No
DDRII/I SDRAM Clock Out — Provides the
negative differential clocks to the external
SDRAM memory subsystem.
D_CK_N[2:0] /
DDR_CK_N[2:0]
O
O
O
O
O
Same as above
No
Yes
Yes
Yes
Yes
Chip Select — Must be asserted for all
transactions to the DDRII/I SDRAM device.
One per bank.
D_CS_N[1:0] /
C_CS_N[1:0]
Use the same CS to control 32-bit
data + 8-bit ECC, per bank
The RAS signal must be connected
to each device in a daisy chain
manner
Row Address Strobe — Indicates that the
current address on D_MA[13:0] /
DDR_MA[13:0] is the row.
D_RAS_N /
DDR_RAS_N
The CAS signal must be connected
to each device in a daisy chain
manner
Column Address Strobe — Indicates that the
current address on D_MA[13:0] /
DDR_MA[13:0] is the column.
D_CAS_N /
DDR_CAS_N
The WE signal must be connected
to each device in a daisy chain
manner
Write Strobe — Defines whether or not the
current operation by the DDRII/I SDRAM is to
be a read or a write.
D_WE_N / DDR_WE_N
Data Bus Mask — Controls the DDRII/I SDRAM
data input buffers. Asserting D_WE_N/
DDR_WE_N causes the data on D_DQ[31:0]/
DDR_DQ[31:0] and D_CB[7:0]/DDR_CB[7:0]
to be written into the DDRII/I SDRAM devices.
Connect to each DM device pin.
For the 8-bit devices connect one
DM signal per device.
D_DM[4:0] /
DDR_DM[4:0]
O
O
Yes
Yes
For the 16-bit devices connect two
DM signal per device (depending
on how many data bits are being
used).
D_DM[4:0]/DDR_DM[4:0] controls this
operation on a per-byte basis. D_DM[3:0]/
DDR_DM[3:0] are intended to correspond to
each byte of a word of data. D/DM[4]/
DDR_DM[4] is intended to be utilized for the
ECC byte of data.
DDRII/I SDRAM Bank Selects — Controls which
of the internal DDRII/I SDRAM banks to read
or write. D_BA[1:0]/DDR_BA[1:0] are used for
all technology types supported.
The BA signals must be connected
to each device in a daisy chain
manner.
D_BA[1:0] /
DDR_BA[1:0]
Address bits 13 through 0 — Indicates the row
or column to access depending on the state of
D_RAS_N/DDR_RAS_N and D_CAS_N/
DDR_CAS_N.
All address signals must be
connected to each device in a
daisy chain manner.
D_MA[13:0] /
DDR_MA[13:0]
O
Yes
Yes
D_DQ[31:0] /
DDR_DQ[31:0]
Must be connected in parallel to
achieve a 32-bit bus width.
I/O
Data Bus — 32-bit wide data bus.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
19
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Table 4.
DDRII/I SDRAM Interface Pin Description (Sheet 2 of 2)
VTT
Terminatio
n
Type
Field
Name
Device-Pin Connection
Description
ECC Bus — Eight-bit error correction code
which accompanies the data on D_DQ[31:0]/
DDR_DQ[31:0].
When ECC is disabled and not being used in a
system design, these signals can be left un-
connected.
D_CB[7:0] /
I/O
I/O
Connect to ECC memory devices.
Yes
Yes
DDR_CB[7:0]
Data Strobes Differential — Strobes that
accompany the data to be read or written from
the DDRII/I SDRAM devices. Data is sampled
on the negative and positive edges of these
strobes. D_DQS[3:0]/DDR_DQS[3:0] are
intended to correspond to each byte of a word
of data. D_DQS[4]/DDR_DQS[4] is intended to
be utilized for the ECC byte of data.
Connect DQS[3:0] to devices with
data signals and DQS[4] to
devices with ECC signals.
D_DQS[4:0] /
DDR_DQS[4:0]
Clock enables — One clock after D_CKE[1:0]/
DDR_CKE[1:0] is de-asserted, data is latched
on D_DQ[31:0]/DDR_DQ[31:0] and
D_CB[7:0]/DDR_CB[7:0]. Burst counters
within DDRII/I SDRAM device are not
incremented. De-asserting this signal places
the DDRII/I SDRAM in self-refresh mode. For
normal operation, D_CKE[1:0]/DDR_CKE[1:0]
must be asserted.
Use one CKE per bank, never mix
the CKE on the same bank. Use
CKE[0] for bank0 and CKE[1] for
bank1
D_CKE[1:0] /
DDR_CKE[1:0]
O
Yes
On Die Termination Control — Turns on DDR II
SDRAM termination during writes.
D_ODT[1:0]
D_RES[2:1]
Compensation for DDR OCD (analog) DDRII
mode only. This function is not enable and
special connection is required.
Refer to Figure 27
Refer to Figure 27
Refer to Figure 27
Compensation Voltage Reference (analog) for
DDR driver slew rate control connected
through a resistor to D_CRES0.
D_SLWCRES
D_IMPCRES
Compensation Voltage Reference (analog) for
DDR driver impedance control connected
through a resistor to D_CRES0.
Analog VSS Ref Pin (analog) both D_SLWCRES
and D_IMPCRES signals connect to this pin
through a reference resistor. For DDRII/I
respectively:
Tied off to a - 285 / 387Ohm Resistor connected to
D_CRES0
O
Tied off to a resistor
resistor
DDR_IMPCRES used for process and
temperature adjustments.
- 825 / 845Ohm Resistor connected to
DDR_SLWCRES used for process and
temperature adjustments.
DDRII/IDDRII/I SDRAM Voltage Reference — is
used to supply the reference voltage to the
differential inputs of the memory controller
pins.
D_VREF / DDR_VREF
I
VCCDDR/2
VCCDDR/2
3.2.2
DDRII/I SDRAM Initialization
For instructions on DDRII/I SDRAM initialization, refer to DDR SDRAM Initialization
®
subsection in the Memory Controller chapter of the Intel IXP43X Product Line of
Network Processors Developer’s Manual.
®
Intel IXP43X Product Line of Network Processors
HDG
20
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
3.3
Expansion Bus
The Expansion Bus of the IXP43X network processors is specifically designed for
compatibility with Intel-and Motorola* style microprocessor interfaces.
The expansion bus controller includes a 24-bit address bus and a 16-bit wide data path,
running at a maximum speed of 80 MHz from an external clock oscillator. The bus can
be configure to support the following target devices:
• Intel multiplexed
• Intel non-multiplexed
®
®
• Intel StrataFlash
• Synchronous Intel StrataFlash Memory
• Motorola multiplexed
• Motorola non multiplexed
The expansion bus controller also has an arbiter that supports up to four external
devices that can master the expansion bus. External masters can be used to access
external slave devices that reside on the expansion bus, including access to internal
memory mapped regions within the IXP43X network processors.
All supported modes are seamless and no additional glue logic is required. Other cycle
types can be supported by configuring the Timing and Control Register for Chip Select.
The expansion interface functions support 8-bit or 16-bit data operation and allows an
address range of 512 bytes to 16 MBs, using 24 address lines for each of the four
independent chip selects.
Access to the expansion-bus interface is completed in five phases. Each of the five
phases can be lengthened or shortened by setting various configuration registers on a
per-chip-select basis. This feature allows the IXP43X network processors to connect to
a wide variety of peripheral devices with varying speeds.The expansion interface
supports Intel or Motorola* microprocessor style bus cycles. The bus cycles can be
configured to be multiplexed address/data cycles or separate address/data cycles for
each of the four chip-selects.
The expansion interface is an asynchronous interface to externally connected chips. A
clock is supplied to the IXP43X network processors expansion interface for the interface
to operate. This clock can be driven from GPIO 15 or an external source. Devices on the
expansion bus can be clocked by an external clock at a rate of up to 80 MHz. If GPIO 15
is used as the clock source, the Expansion Bus interface can only be clocked at a
maximum of 33.33 MHz. GPIO 15’s maximum clock rate is 33.33 MHz.
3.3.1
Signal Interface
Table 5.
Expansion Bus Signal Recommendations (Sheet 1 of 2)
Pull
Type
Field
Name
Up
Recommendations
Down
EX_CLK
EX_ALE
I
No
No
Use series termination resistor, 10Ω to 33Ω at the source.
Use series termination resistor, 10Ω to 33Ω at the source.
TRI O
Use 470Ω resistors for pull-downs; required for boot strapping for initial configuration of
Configuration Register 0. Pull-ups are not required as for when the system comes out of
reset, all bits are initially set HIGH. For more details, see Table 6.
For additional details on address strapping, see the Intel IXP43X Product Line of Network
Processors Developer’s Manual.
EX_ADDR[23:0]
I/O
Yes
®
EX_WR_N
EX_RD_N
I/O
I/O
No
No
Use series termination resistor, 10Ω to 33Ω at the source.
Use series termination resistor, 10Ω to 33Ω at the source.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
21
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Table 5.
Expansion Bus Signal Recommendations (Sheet 2 of 2)
Pull
Up
Down
Type
Field
Name
Recommendations
Use series termination resistor, 10Ω to 33Ω at the source.
Use 10KΩ resistors pull-ups to ensure that the signal remains de-asserted.
EX_CS_N[3:0]
I/O
Yes
EX_DATA[15:0]
EX_IOWAIT_N
I/O
I
No
Expansion-bus, bidirectional data.
Yes
Should be pulled high through a 10-KΩ resistor when not being utilized in the system.
3.3.2
Reset Configuration Straps
At power up or whenever RESET_IN_N is asserted, the Expansion-bus address outputs
are switched to inputs and the state of the inputs are captured and stored in
Configuration Register 0, bits 23 through 0. This occurs when PLL_LOCKED is de-
asserted.
The strapping of Expansion-bus address pins can be done by placing external pull-down
resistors at the required address pin. It is not required to use external pull-up resistors,
by default upon reset all bits on Configuration Register 0 are set High, unless an
external pull down is used to set them Low. For example to register a bit low or high in
the Configuration Register 0, do the following:
Place an external 470Ω pull-down resistor to register a bit LOW in the Configuration
Register 0.
No external pull-up is required; upon reset, bits are set high by default.
The state of the boot-strapping resistor is registered on the first cycle after the
synchronous de-assertion of the reset signal. These bits can be read or written as
needed for desired configurations. It is recommended that only Bit 31, Memory Map, be
changed from 1 to 0 after execution of boot code from external flash.
®
Refer to the Intel IXP43X Product Line of Network Processors Developer’s Manual for
a complete bit description of Configuration Register 0.
Table 6.
Boot/Reset Strapping Configuration (Sheet 1 of 2)
Name
Function
Description
®
®
Intel XScale
Processor
Allow a slower Intel XScale Processor clock speed to override device fuse settings.
But cannot be used to over clock core speed. Refer to Table 7 for additional
information.
EX_ADDR[23:21]
Clock Set[2:0]
EX_ADDR[20:17]
EX_ADDR[16:12]
Customer
Customer-defined bits. (Might be used for board revision.)
(Reserved)
(Reserved)
DDRI or DDRII mode selection:
0 - DDRII mode (400MHz)
1 - DDRI mode (266MHz)
EX_ADDR[11]
DDR_MODE
DDR_mode or DDR clock speed selection bit is read only and strapped in from exp
address bit 11 upon activation of reset_early_n and reset_cold_n.
®
Intel IXP43X Product Line of Network Processors
HDG
22
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Table 6.
Boot/Reset Strapping Configuration (Sheet 2 of 2)
Name
Function
Description
1 = EX_IOWAIT_N is sampled during the read/write expansion bus cycles for Chip
Select 0.
0 = EX_IOWAIT_N is ignored for read and write cycles to Chip select 0 if
®
EXP_TIMING_CS0 is configured to Intel mode that is mentioned in Intel IXP43X
®
Product Line of Network Processors Datasheet and Intel IXP43X Product Line of
Network Processors Developer’s Manual.
Typically, IOWAIT_CS0 must be pulled down to Vss when attaching a Synchronous
®
Intel StrataFlash on Chip Select 0 since the default mode for EXP_TIMING_CS0 is
Intel mode and EX_IOWAIT_N is an unknown value for Synchronous Intel
StrataFlash.
EX_ADDR[10]
IOWAIT_CS0
If the board does not connect the Synchronous Intel StrataFlash WAIT pin to
EX_WAIT_N (and the board guarantees EX_IOWAIT_N is pulled up), the value of
IOWAIT_CS0 is a don’t-care, since EX_IOWAIT_N will not be asserted.
When EXP_TIMING_CS0 is reconfigured to Intel Synchronous mode during
boot-up (for synchronous Intel chips), the expansion bus controller ignores
EX_IOWAIT_N during read and write cycles since the WAIT functionality is
determined from the EXP_SYNCINTEL_COUNT and EXP_TIMING_CS registers.
EX_ADDR[9]
EX_ADDR[8]
EXP_MEM_DRIVE
USB Clock
Refer to table found in EX_ADDR[5].
Controls the USB clock select.
1 = USB Host/Device clock is generated internally
0 = USB Device clock is generated from GPIO[0].
When generating a spread spectrum clock on OSC_IN, GPIO[1] can be driven from
the system board to generate a 48 MHz clock for the USB Host.
Selects the data bus width of the FLASH memory device found on Chip Select 0.
Refer to 8/16_FLASH bit (Bit 0) of this register as well.
0 = 8 or 16-bit data bus size (must be pulled down during address strapping)
1 = not supported
EX_ADDR[7]
EX_ADDR[6]
32_FLASH
(Reserved)
(Reserved)
Expansion bus low/medium/high drive strength. The drive strength depends on
EXP_DRIVE and EXP_MEM_DRIVE configuration bits.
EXP_MEM_DRIVE EXP_DRIVE
Expansion drive strength
------------------------------------------------------------------------------------
EX_ADDR[5]
EXP_DRIVE
0
0
1
1
0
1
0
1
Reserved
Medium Drive
Low Drive
High Drive
Sets the clock speed of the PCI Interface
EX_ADDR[4]
EX_ADDR[3]
EX_ADDR[2]
PCI_CLK
(Reserved)
PCI_ARB
0 = 33 MHz (must be pulled down during address strapping)
1 = not supported
(Reserved). EX_ADDR[3] must not be pulled down during address strapping. This
bit must be written to ‘1’ if performing a write to this register.
Enables the PCI Controller Arbiter
0 = PCI arbiter disabled
1 = PCI arbiter enabled
Configures the PCI Controller as PCI Bus Host
0 = PCI as non-host
1 = PCI as host
EX_ADDR[1]
EX_ADDR[0]
PCI_HOST
Specifies the data bus width of the FLASH memory device found on Chip Select 0.
8/16_FLASH
Data bus size
16-bit
8/16_FLASH
0
1
8-bit
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
23
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
®
Table 7.
Setting Intel XScale Processor Operation Speed
®
Intel XScale Processor
Cfg0
Cfg1
Cfg_en_n
Actual Core Speed
(MHz)
Speed
EX_ADDR[21] EX_ADDR[22] EX_ADDR[23]
(Factory Part Speed)
667 MHz
667 MHz
667 MHz
667 MHz
667 MHz
X
0
1
0
1
X
0
0
1
1
1
0
0
0
0
667 MHz
667 MHz
533 MHz
266 MHz
400 MHz
533 MHz
533 MHz
533 MHz
533 MHz
533 MHz
X
0
1
0
1
X
0
0
1
1
1
0
0
0
0
533 MHz
533 MHz
533 MHz
266 MHz
400 MHz
400 MHz
400 MHz
400 MHz
400 MHz
400 MHz
X
0
1
0
1
X
0
0
1
1
1
0
0
0
0
400 MHz
400 MHz
400 MHz
266 MHz
400 MHz
266 MHz
X
X
X
266 MHz
Note:
The Intel XScale processor can operate at slower speeds than the factory programmed
speed setting. This is done by placing a value on Expansion bus address bits 23,22,21
when PLL_LOCK is deasserted and knowing the speed grade of the part from the
factory. Column 1 above denotes the speed grade of the part from the factory. Column
2, 3, and 4 denotes the values captured on the Expansion Bus address bits when
PLL_LOCK is deasserted. Column 5 represents the speed at which the Intel XScale
processor speed is operating at.
3.3.3
8-Bit Device Interface
The IXP43X network processors support 8-bit-wide data bus devices (byte mode). For
interface cycles, the data lines and control signals can be connected as shown in
Figure 3 on page 26. During byte mode accesses, the remaining data signals not being
used EX_DATA[15:8], are driven by the processor to an unpredictable state on WRITE
cycles and tri-stated during READ cycles.
When booting an 8-bit flash device, the expansion bus must be configured during reset
to the 8-bit mode, bit 0 and 7 of Configuration Register 0 must be set as follows (see
Table 6):
Bit 0 = 1. By default this bit is set high when coming off reset or any time reset is
asserted.
Bit 7 = 0. This can be done by placing an external 470 ohm pull-down resistor to the
pin EX_ADDR[7].
®
Intel IXP43X Product Line of Network Processors
HDG
24
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Boot-strapping is required in certain address pins of the Expansion bus. If it is required
to change access mode, after the system has booted, and during normal operation; the
Timing and Control Register for Chip Select must be configured to perform the desired
mode access. For a complete description on accomplishing this refer to the Expansion
®
Bus chapter in the Intel IXP43X Product Line of Network Processors Developer’s
Manual.
3.3.4
16-Bit Device Interface
mode). For Intel interface cycles, the data lines and control signals can be connected as
shown in Figure 3 on page 26.
When booting a 16-bit flash device, the expansion bus must be configured during reset
to the 16-bit mode (see Configuration Register 0).
Bit 0 = 0. This can be done by placing an external 470 ohm pull-down resistor to the
pin EX_ADDR[0].
Bit 7 = 0. This can be done by placing an external 470 ohm pull-down resistor to the
pin EX_ADDR[7].
Boot-strapping is required in certain address pins of the Expansion bus.To change to
access mode after booting the system and during normal operation, the Timing and
Control Register for Chip Select must be configured to perform the desired mode
access. For a complete description on how to accomplish this refer to the Expansion
®
Bus chapter in the Intel IXP43X Product Line of Network Processors Developer’s
Manual.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
25
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Figure 3.
8/16-Bit Device Interface
EX_DATA[15:0]
EX_DATA[7:0]
DATA[7:0]
Intel® IXP43X Product
Line of Network
Processors
8-Bit Device
Byte Access
EX_ADDR[23:0]
EX_ADDR[23:0]
ADDR[23:0]
EX_CS_N
EX_RD_N
EX_WR_N
CS
OE
WR
CS_N
OE_N
WR_N
EX_DATA[15:0]
EX_DATA[15:0]
DATA[15:0]
Intel® IXP43X Product
Line of Network
16-Bit Device
16-Bit-Word Access
ADDR[23:0]
Processors
EX_ADDR[23:0]
EX_ADDR[23:0]
EX_CS_N
EX_RD_N
EX_WR_N
CS
OE
WR
CS_N
OE_N
WR_N
B4095-004
3.3.5
Figure 4 illustrates how a boot ROM is connected to the expansion bus. The flash (ROM)
®
used in the block diagram is the Intel StrataFlash memory device TE28F256J3D —
32-Mbyte, 16-bit, flash in the 56-TSOP package. The Intel StrataFlash memory
TE28F256J3D is part of the 0.18-µm, 3.3-V Intel StrataFlash memory.
.
®
Intel IXP43X Product Line of Network Processors
HDG
26
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Figure 4.
Flash Interface Example
EX_DATA[15:0]
DATA[15:0]
EX_DATA[15:0]
EX_ADDR[23:0]
Intel® IXP43X Product
16-Bit Device
16-Bit-Word Access
ADDR[23:0]
Line of Network
Processors
EX_ADDR[23:0]
EX_CS_N
EX_RD_N
EX_WR_N
CS
OE
WR
CE0
OE_N
WR_N
Intel® Flash
3.3 V
RST#
RP_N
CE1
CE2
0 KΩ
4.7 KΩ
BYTE_N
VPEN_N
4.7 KΩ
B4097-005
3.4
UART Interface
The UART interface are a 16550-compliant UART with the exception of transmit and
receive buffers. Transmit and receive buffers are 64 bytes-deep versus the 16 bytes
required by the 16550 UART specification.
The interface can be configured to support speeds from 1,200 Baud to 921 Kbaud. The
interface supports the following configurations:
• Five, six, seven, or eight data-bit transfers
• One or two stop bits
• Even, odd, or no parity
The request-to-send (RTS0_N) and clear-to-send (CTS0_N) modem control signals also
are available with the interface for hardware flow control. The hardware supports a
four-wire interface:
• Transmit Data
• Receive Data
• Request to Send
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
27
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
• Clear to Send
Note:
The UART module does not support full modem functionality. However, this can be
implemented, by using GPIO ports to generate DTR, DSR, RI, and DCD and making
some changes to the driver.
3.4.1
Signal Interface
Table 8.
UART Signal Recommendations
Pull
Type
Field
Name
Up/
Recommendations
Down
Serial data input Port 0.
RXDATA0
TXDATA0
CTS0_N
RTS0_N
I
O
I
Yes
No
When signal is not being used in the system, this pin should be pulled high with a 10-KΩ
resistor.
Serial data output Port 0.
Clear-To-Send Port 0.
\When signal is not being used in the system, this pin should be pulled high with a 10-KΩ
resistor.
Yes
No
O
Request-To-Send Port 0.
The following figure contain a typical four signal interface between the UART and an
RS-232 transceiver driver, required to interface with external devices. Unused inputs to
the RS-232 driver can be connected to ground. This avoids signals floating to
undetermined states which can cause over heating of the driver leading to permanent
damage.
®
Intel IXP43X Product Line of Network Processors
HDG
28
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Figure 5.
UART Interface Example
DB9
Connector (Female)
1 DCD
1
2
CTS0_N
OUT4
IN3
2 RX
6
7
RTS0_N
RXDATA0
TXDATA0
IN1
OUT3
OUT2
3 TX
OUT1
IN2
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 RI
3
4
5
IN4
8
9
Intel® IXP43X
Intel® IXP43X
Product Line of
NC
Product Line of
Network Processors
RS-232
Transceiver
Network Processors
B4099-005
3.5
MII Interface
The IXP43X network processors support a maximum of two Ethernet MACs. Depending
on the part number of the IXP43X network processors, various combinations can be
®
used. Refer to the Intel IXP43X Product Line of Network Processors Datasheet for a
detailed list of features that can be enabled depending upon your requirements.
All MACs contained in the NPEs are compliant to the IEEE 802.3 specification and
handle flow control for the IEEE 802.3Q VLAN specification.
The Management Data Interface (MDI) supports a maximum of 32 PHY addresses. MDI
signals are required to be connected to every PHY chip. Each PHY port is assign a
unique address in the external PHY chip from 0 to 31, totaling a maximum of 32 PHY
addresses. The maximum number of MACs supported by the IXP43X network
processors is two.
The MII interface supports clock rates of 25 MHz for 100-Mbps operation or 2.5 MHz for
10-Mbps operation.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
29
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
3.5.1
Signal Interface MII
Table 9.
MII NPE A Signal Recommendations
Pull
Type
Name
Up/
Recommendations
Field
Down
Transmit Clock.
ETHA_TXCLK
I
Yes
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor.
ETHA_TXDATA[3:0]
ETHA_TXEN
O
O
No
No
Transmit Data.
Transmit Enable.
Receive Clock.
ETHA_RXCLK
ETHA_RXDATA[3:0]
ETHA_RXDV
I
I
I
I
I
Yes
Yes
Yes
Yes
Yes
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor.
Receive Data.
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor.
Receive Data Valid.
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor.
Collision Detect.
ETHA_COL
If operating in a full duplex mode and there is no requirement to use the Collision
Detect signal, then the pin must be pulled low with a 10-KΩ resistor.
Carrier Sense.
ETHA_CRS
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor.
Notes:
1.
2.
3.
Features disabled/enabled by Soft Fuse must be done during the boot-up sequence. A feature cannot be enabled after
being disabled without asserting a system reset.
Features disabled by a specific part number, do not require pull-ups or pull-downs. Therefore, all pins can be left
unconnected.
Features enabled by a specific part number — and required to be Soft Fuse-disabled, as stated in Note 1 — only require
pull-ups or pull-downs in the clock-input signals.
Table 10.
MII NPE C Signal Recommendations (Sheet 1 of 2)
Pull
Type
Field
Name
Up/
Recommendations
Down
Externally supplied transmit clock.
•
•
25 MHz for 100 Mbps operation
2.5 MHz for 10 Mbps
ETHC_txclk
I
Yes
This MAC contains hardware hashing capabilities that are local to the interface.
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor.
Transmit data bus to PHY, asserted synchronously with respect to ETHC_TXCLK. This
MAC contains hardware hashing capabilities that are local to the interface.
ETHC_txdATA[3:0]
ETHC_txen
O
O
No
Indicates that the PHY is being presented with nibbles on the MII interface. Asserted
synchronously, with respect to ETHC_TXCLK, at the first nibble of the preamble, and
remains asserted until all the nibbles of a frame are presented. This MAC contains
hardware hashing capabilities that are local to the interface.
Yes
®
Intel IXP43X Product Line of Network Processors
HDG
30
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Table 10.
MII NPE C Signal Recommendations (Sheet 2 of 2)
Pull
Type
Field
Name
Up/
Recommendations
Down
Externally supplied receive clock:
•
•
25 MHz for 100 Mbps operation
2.5 MHz for 10 Mbps
ETHC_rxclk
I
Yes
This MAC contains hardware hashing capabilities that are local to the interface.
Should be pulled high through a 10-KΩ resistor when not being utilized in the system.
Receive data bus from PHY, data sampled synchronously, with respect to ETHC_RXCLK.
This MAC contains hardware hashing capabilities that are local to the interface.
Should be pulled high through a 10-KΩ resistor when not being utilized in the system.
ETHC_rxdATA[3:0]
ETHC_rxdv
I
I
Yes
Yes
Receive data valid is used to inform the MII interface about data that is being sent by
the Ethernet PHY
This MAC contains hardware hashing capabilities that are local to the interface.
Should be pulled high through a 10-KΩ resistor when not being utilized in the system.
Asserted by the PHY when a collision is detected by the PHY. This MAC contains
hardware hashing capabilities that are local to the interface.
Should be pulled high through a 10-KΩ resistor when not being utilized in the system
ETHC_col
I
I
Yes
Yes
When this interface is disabled through the NPE-C Ethernet soft fuse (refer to the
®
Expansion Bus Controller chapter of the Intel IXP43X Product Line of Network
Processors Developer’s Manual) and is not being used a system design, this interface/
signal is not required for any connection.
Asserted by the PHY when the transmit medium or receive medium are active.
De-asserted when both the transmit and receive medium are idle. Remains asserted
throughout the duration of collision condition. PHY asserts CRS asynchronously and
de-asserts synchronously with respect to ETHC_RXCLK.
ETHC_crs
This MAC contains hardware hashing capabilities that are local to the interface.
Should be pulled high through a 10-KΩ resistor when not being utilized in the system.
Notes:
1.
2.
3.
Features disabled/enabled by Soft Fuse must be done during the boot-up sequence. A feature cannot be enabled after
being disabled without asserting a system reset.
Features disabled by a specific part number, do not require pull-ups or pull-downs. Therefore, all pins can be left
unconnected.
Features enabled by a specific part number — and required to be Soft Fuse-disabled, as stated in note 1 — only require
pull-ups or pull-downs in the clock-input signals.
Table 11.
MAC Management Signal Recommendations - NPE A and NPE C
Pull
Type
Field
Name
Up/
Recommendations
Down
NPE A and NPE C
Management data input output. Provides the write data to both PHY devices connected to
each MII interface. An external pull-up resistor of 1.5K ohm is required on
ETHC_MDIO to properly quantify the external PHYs used in the system. For specific
implementation, see the IEEE 802.3 specification.
ETH_mdio
IO
Yes
No
Should be pulled high through a 10-KΩ resistor when not being utilized in the system
NPE A and NPE C
Management data clock. Management data interface clock is used to clock the MDIO signal as
an output and sample the MDIO as an input. The ETHC_MDC is an input on power up and can
ETH_mdc
O
®
be configured to be an output through Intel APIs documented in the Intel IXP400 Software
Programmer’s Guide
3.5.2
Device Connection, MII
Figure 6 is a typical example of an Ethernet PHY device interfacing to one of the MACs
via the MII hardware protocol.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
31
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Figure 6.
MII Interface Example
Intel® IXP43X
Product Line of
Network Processors
10/100
PHY
TXEN
ETH_TXEN
ETH_TXCLK
TXCLK
TXDATA[3:0]
ETH_TXDATA[3:0]
ETH_RXDV
ETH_RXCLK
RXDV
Magnetics
RJ45
RXCLK
ETH_RXDATA[3:0]
RXDATA[3:0]
ETH_COL
ETH_CRS
COL
CRS
25 MHz
VCC (3.3 V)
1.5 KΩ
MDIO
MDC
ETH_MDIO
ETH_MDC
MII Interface
B4101-004
3.6
GPIO Interface
The IXP43X network processors provide 16 general-purpose input/output pins to
generate and capture application-specific input and output signals. Each individual pin
can be programmed as an input or output.
When programmed as an input, GPIO 0 to GPIO 12 can be configured to be an interrupt
source. Interrupt sources can be configured to detect either active high, active low,
rising edge, falling edge, or transitional. In addition, GPIO14 and GPIO15 can be
programmed to provide a user-programmable clock out.
During reset, all pins are configured as inputs and remain in this state until configured
otherwise, with the exception of GPIO15, which by default provides a clock output. The
driver strength of GPIO pins is sufficient to drive external LEDs with a proper limiting
resistor.
®
Intel IXP43X Product Line of Network Processors
HDG
32
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
3.6.1
Signal Interface
Table 12.
GPIO Signal Recommendations
Pull
Type
Name
Up/
Recommendations
Field
Down
General Purpose Input/Output.
If used as an input interrupt (only GPIO [12:0]), should be pull-up or pull-down, depending
on the level of activation. For example:
GPIO[13:0]
IO
Yes
Active high, use a 10-KΩ pull-down resistor.
Active low, use a 10-KΩ pull-up resistor.
Should be pulled high through a 10-KΩ resistor when not used.
Note: Alternate function for GPIO[1] - External USB 48 MHz Bypass Clock
General Purpose Input/Output.
GPIO[14]
GPIO[15]
IO
IO
Yes
Yes
Same recommendations as GPIO[13:0]. An additional feature includes Clock generation, max
clock out 33.33 MHz., set as input by default.
General Purpose Input/Output.
Same recommendations as GPIO[13:0]. An additional feature includes Clock generation, max
clock out 33.33 MHz., set as output by default.
3.6.2
Design Notes
The drive strength for GPIO[15:14] is limited to 8 mA, while GPIO [13:0] can output up
to 16 mA. When used for driving high current devices such as LEDs or relays, make
sure to place current-limiting resistor; else there could be permanent damage to the
driver of the IXP43X network processors.
It is recommended that a 10-KΩ pull-up resistor be used when a GPIO port is
configured as an input and not being used.
3.7
USB Interface
There are two USBV2.0 Host Controllers in the IXP43X network processors. It supports
Low-Speed, 1.5 Mbps, Full-Speed, 12 Mbps, High-Speed, 480 Mbps rate and interface
is EHCI compliant.
Supported features are:
• Host function
• Low-speed interface
• Full-speed interface
• High-speed interface
• EHCI register interface
• UTMI+ Level 2 Compliant
The following is a partial list of features that are not supported:
• Device function
• OTG function
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
33
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
3.7.1
Signal Interface
Table 13.
USB Host Signal Recommendations
Pull
Type
Name
Up/
Description
Field
Down
Positive signal of the differential USB receiver/driver for the USB host interface.
Use an 20Ω series termination resistor at the source.
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled low with a 10-KΩ resistor. When this interface is
disabled through the USB Device soft fuse and is not being used in a system design, it
is not required for any connection. Refer to Expansion Bus Controller chapter of the
USB_P0_POS
I/O
I/O
Yes
Yes
®
Intel IXP43X Product Line of Network Processors Developer’s Manual.
Negative signal of the differential USB receiver/driver for the USB host interface.
Use an 20Ω series termination resistor at the source.
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled low with a 10-KΩ resistor. When this interface is
disabled through the USB Device soft fuse and is not being used in a system design, it
is not required for any connection. Refer to Expansion Bus Controller chapter of the
USB_P0_NEG
®
Intel IXP43X Product Line of Network Processors Developer’s Manual.
USB_P0_PWREN
USB_P0_OC
O
I
No
No
Enables the external VBUS power source.
External VBUS power is in over current condition
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled low with a 10-KΩ resistor. When this interface is
disabled through the USB Device soft fuse and is not being used in a system design, it
is not required for any connection. Refer to Expansion Bus Controller chapter of the
®
Intel IXP43X Product Line of Network Processors Developer’s Manual.
Positive signal of the differential USB receiver/driver for the USB host interface.
Use an 20Ω series termination resistor at the source.
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled low with a 10-KΩ resistor. When this interface is
disabled through the USB Device soft fuse. Refer to Expansion Bus Controller chapter
USB_P1_POS
USB_P1_NEG
I/O
I/O
Yes
Yes
®
of the Intel IXP43X Product Line of Network Processors Developer’s Manual.
Negative signal of the differential USB receiver/driver for the USB host interface.
Use an 20Ω series termination resistor at the source.
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled low with a 10-KΩ resistor. When this interface is
disabled through the USB Device soft fuse and is not being used in a system design, it
is not required for any connection. Refer to Expansion Bus Controller chapter of the
®
Intel IXP43X Product Line of Network Processors Developer’s Manual.
USB_P1_PWREN
USB_P1_OC
O
I
No
No
Enable the external VBUS power source.
External VBUS power is in over current condition
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled low with a 10-KΩ resistor. When this interface is
disabled through the USB Device soft fuse and is not being used in a system design, it
is not required for any connection. Refer to Expansion Bus Controller chapter of the
®
Intel IXP43X Product Line of Network Processors Developer’s Manual.
A typical implementation of a USB interface Host down-stream is shown in Figure 9.
The Host controller cannot be used as a Device controller.
Note:
Note:
Depending on the data rate required, Low-speed, Full-speed or High-speed, the 1.5K
resistor shown near the device interface must be connected on the D+ or D-.
Speed configuration at the Device can be set as stated in note 1 and 2 below. For more
details, refer to the Universal Serial Bus Specification, Revision 2.0.
1. If a 1.5-KΩ, pull-up resistor is connected to USB_P_POS line, the USB port is
identified as Full-speed and High-speed mode.
®
Intel IXP43X Product Line of Network Processors
HDG
34
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
2. If a 1.5-KΩ, pull-up resistor is connected to USB_P_NEG line, the USB port is
identified as Low-speed mode.
To maintain signal integrity and minimize end-users termination mismatch, the IXP43X
network processors require external series termination resistors. The value of the
terminating resistors is based on the operational speed and length of the transmission
line.
Refer to following termination guidelines for High-speed:
1. High-speed USB designs require parallel termination at both the transmitter and
receiver. For host controller designs that use external termination resistors, place
the termination resistors as close as possible to the host controller signal pins.
Recommend less than 200 mils if possible. Follow the manufacturer’s
recommendation for the termination value needed to obtain the required 45 ohm to
ground parallel HS termination.
2. For downstream ports, a 15 kΩ pull down resistor on the connector side of the
termination is required for device connection detection purposes. Note that this pull
down might be integrated into the host controller silicon. Follow the manufacturer’s
recommendation for the specific part used.
if they should pass EMI testing. Place the CM choke as close as possible to the
connector as shown in Figure 8 on page 36. Common mode chokes can provide
required noise attenuation. Design can include a common mode choke footprint to
provide a stuffing option in the event the choke is needed to pass EMI testing.
Note:
Common mode chokes degrade signal quality, thus they should only be used if EMI is a
known problem.
Figure 7.
Common Mode Choke
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
35
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Figure 8.
USB RCOMP and ICOMP Pin Requirement
USB_ RBIASP
USB_ RBIASN
Intel®
IXP43X
Product Line
of Network
Processors
22.6
Ω
±1%
resistor
Figure 9.
USB Host Down Stream Interface Example
USB_VDD
Host
Device
Intel® IXP43X
Product Line of
Network
200 mA
0.1 µF
FERRITE
47 µF
0.1 µF
Processors
V_BUS USB_3V3
USB_HPEN
USB_HPWR
4.7 µF
1.5 KΩ
Look at
Note 1&2
20 Ω
USB_HPOS
(D+)
D
+
FERRITE
Device
22 pF 22 pF
D-
15 KΩ
USB
Port
20 Ω
USB_HNEG
(D-)
FERRITE
22 pF 22 pF
15 KΩ
B4105-004
®
Intel IXP43X Product Line of Network Processors
HDG
36
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
3.8
UTOPIA Level 2 Interface
The IXP43X network processors support the industry-standard UTOPIA Level 2 bus
interface. A dedicated Network Processor Engine (NPE) handles segmentation and
reassembly of ATM cells, CRC checking/generation, and transfer of data to/from
memory. This allows parallel processing of data traffic on the UTOPIA interface,
®
off-loading processor overhead required by the Intel XScale Processor.
The UTOPIA module is configured as a master and can support single-PHY (SPHY) or
multi-PHY (MPHY).
The IXP43X network processors are in compliance with the ATM Forum, UTOPIA Level 2
Specification, Revision 1.0. For optimal design results, the guidelines of the
specification should be followed.
3.8.1
Signal Interface
Table 14.
UTOPIA Level 2/MII_A
Pull
Type
Field
Name
Up/
Description
Down
UTOPIA Level 2 Mode of Operation:
UTOPIA Level 2 Transmit clock input. Also known as UTP_TX_CLK. This signal is
used to synchronize all UTOPIA Level 2 transmit output to the rising edge of the
UTP_OP_CLK.
MII Mode of Operation:
Externally supplied transmit clock.
UTP_OP_CLK /
ETHA_TXCLK
I
Yes
•
•
25 MHz for 100 Mbps operation
2.5 MHz for 10 Mbps
When this interface/signal is enabled and is not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor.
UTOPIA Level 2 flow control output signal. Also known as the TXENB_N signal.
Used to inform the selected PHY about data transmission. Placing the PHY’s
address on the UTP_OP_ADDR and bringing UTP_OP_FCO to logic 1 during the
current clock, followed by the UTP_OP_FCO going to a logic 0, on the next clock
cycle, selects the PHY that is active in MPHY mode.
In SPHY configurations, UTP_OP_FCO is used to inform the PHY that the
processor is ready to send data.
UTP_OP_FCO
UTP_OP_SOC
TRI
TRI
TRI
Yes
Yes
No
This signal is tied to Vcc with an external 10-KΩ resistor.
Start of Cell. Also known as TX_SOC.
Active high signal is asserted when UTP_OP_DATA contains first valid byte of a
transmitted cell.
This signal is tied to Vss with an external 10-KΩ resistor.
UTOPIA Level 2 Mode of Operation:
UTOPIA Level 2 output data. Also known as UTP_TX_DATA. Used to send data
from the processor to an ATM UTOPIA Level 2-compliant PHY.
UTP_OP_DATA[3:0] /
ETHA_TXDATA[3:0]
MII Mode of Operation:
Transmit data bus to PHY, asserted synchronously with respect to ETHA_TXCLK.
This MAC interface does not contain hardware hashing capabilities that are local
to the interface. In this mode of operation the pins represented by this interface
are ETHA_TXDATA[3:0].
®
††
Refer to the Intel IXP43X Product Line of Network Processors Developer’s Manual for information on how to select an
interface.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
37
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Pull
Up/
Down
Type
Field
Name
Description
UTOPIA Level 2 Mode of Operation:
UTOPIA Level 2 output data. Also known as UTP_TX_DATA. Used to send data
from the processor to an ATM UTOPIA Level 2-compliant PHY.
MII Mode of Operation:
UTP_OP_DATA[4] /
ETHA_TXEN
TRI
No
Indicates that the PHY is being presented with nibbles on the MII interface.
Asserted synchronously, with respect to ETHA_TXCLK, at the first nibble of the
preamble, and remains asserted until all the nibbles of a frame are presented.
This MAC does not contain hardware hashing capabilities that are local to the
interface.
UTOPIA Level 2 Mode of Operation:
UTP_OP_DATA[7:5]
UTP_OP_ADDR[4:0]
TRI
I/O
No
UTOPIA Level 2 output data. Also known as UTP_TX_DATA. Used to send data
from the processor to an ATM UTOPIA Level 2-compliant PHY.
Transmit PHY address bus. Used by the processor when operating in MPHY
mode to poll and select a single PHY at any given time.
When this interface/signal is enabled and is not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor. When this
interface is disabled through the UTOPIA Level 2 and/or the NPE-A Ethernet soft
fuse and is not being used in a system design, it is not required for any
Yes
®
connection. Refer to Expansion Bus Controller chapter of the Intel IXP43X
Product Line of Network Processors Developer’s Manual.
UTOPIA Level 2 Output data flow control input: Also known as the TXFULL/CLAV
signal.
Used to inform the processor, the ability of each polled PHY to receive a complete
cell. For
cell-level flow control in an MPHY environment, TxClav is an active high tri-
stateable signal from the MPHY to ATM layer.
The UTP_OP_FCI is connected to multiple MPHY devices. It sees the logic high
generated by the PHY, one clock after the given PHY address is asserted and a
full cell can be received by the PHY. The UTP_OP_FCI sees a logic low generated
by the PHY one clock cycle, after the PHY address is asserted, and a full cell
cannot be received by the PHY.
UTP_OP_FCI
I
Yes
When this interface/signal is enabled and is not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor. When this
interface is disabled through the UTOPIA Level 2 and/or the NPE-A Ethernet soft
fuse and is not being used in a system design, it is not required for any
®
connection. Refer to Expansion Bus Controller chapter of the Intel IXP43X
Product Line of Network Processors Developer’s Manual.
UTOPIA Level 2 Mode of Operation:
UTOPIA Level 2 Receive clock input. Also known as UTP_RX_CLK.
This signal is used to synchronize all UTOPIA Level 2-received inputs to the rising
edge of the UTP_IP_CLK.
MII Mode of Operation:
UTP_IP_CLK /
ETHA_RXCLK
Externally supplied receive clock.
I
Yes
•
•
25 MHz for 100 Mbps operation
2.5 MHz for 10 Mbps
This MAC interface does not contain hardware hashing capabilities that are local
to the interface.
When this interface/signal is enabled and is not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor.
®
††
Refer to the Intel IXP43X Product Line of Network Processors Developer’s Manual for information on how to select an
interface.
®
Intel IXP43X Product Line of Network Processors
HDG
38
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Pull
Up/
Down
Type
Field
Name
Description
UTOPIA Level 2 Input Data flow control input signal. Also known as RXEMPTY/
CLAV.
Used to inform the processor of the ability of each polled PHY to send a complete
cell. For cell-level flow control in an MPHY environment, RxClav is an active high
tri-stateable signal from the MPHY to ATM layer. The UTP_IP_FCI, which is
connected to multiple MPHY devices, sees logic high generated by the PHY, one
clock after the given PHY address is asserted, when a full cell can be received by
the PHY. The UTP_IP_FCI sees a logic low generated by the PHY, one clock cycle
after the PHY address is asserted if a full cell cannot be received by the PHY.
UTP_IP_FCI
I
Yes
In a SPHY mode, this signal is used to indicate to the processor that the PHY has
an octet or cell available for transferring to the processor.
When this interface/signal is enabled and is not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor. When this
interface is disabled through the UTOPIA Level 2 and/or the NPE-A Ethernet soft
®
fuse (refer to Expansion Bus Controller chapter of the Intel IXP43X Product Line
of Network Processors Developer’s Manual) and is not being used in a system
design, the interface/signal is not required for any connection.
Start of Cell. RX_SOC
Active-high signal that is asserted when UTP_IP_DATA contains the first valid
byte of a transmitted cell.
When this interface/signal is enabled and is not being used in a system design,
the interface/signal should be pulled high with a 10KΩ resistor. When this
interface is disabled through the UTOPIA Level 2 and/or the NPE-A Ethernet soft
fuse and is not being used in a system design, it is not required for any
connection. Refer to Expansion Bus Controller chapter of the Intel IXP43X
Product Line of Network Processors Developer’s Manual.
UTP_IP_SOC
I
Yes
®
UTOPIA Level 2 Mode of Operation:
UTOPIA Level 2 input data. Also known as RX_DATA.
Used by the processor to receive data from an ATM UTOPIA Level 2-compliant
PHY.
MII Mode of Operation:
Receives data bus from the PHY; asserted synchronously with respect to
ETHA_RXCLK.
When the interface/signal is enabled and is not being used in a system design, it
UTP_IP_DATA[3:0] /
ETHA_RXDATA[3:0]
I
Yes
should be pulled high with a 10KΩ resistor.
When the interface is disabled through the UTOPIA Level 2 and/or the NPE-A
Ethernet soft fuse and is not being used in a system design, it is not required for
®
any connection. (Refer to Expansion Bus Controller chapter of the Intel IXP43X
Product Line of Network Processors Developer’s Manual).
UTOPIA Level 2 Mode of Operation:
UTOPIA Level 2 input data. Also known as RX_DATA.
Used by to the processor to receive data from an ATM UTOPIA Level 2-compliant
PHY.
MII Mode of Operation:
Receive data valid used to inform the MII interface about data that is being sent
by the Ethernet PHY.
This MAC does not contain hardware hashing capabilities that are local to the
interface.
UTP_IP_DATA[4] /
ETHA_RXDV
I
Yes
When the interface/signal is enabled and is not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor. When this
interface is disabled through the UTOPIA Level 2 and/or the NPE-A Ethernet soft
fuse (and is not being used in a system design, it is not required for any
®
connection. Refer to Expansion Bus Controller chapter of the Intel IXP43X
Product Line of Network Processors Developer’s Manual.
®
††
Refer to the Intel IXP43X Product Line of Network Processors Developer’s Manual for information on how to select an
interface.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
39
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Pull
Up/
Down
Type
Field
Name
Description
UTOPIA Level 2 Mode of Operation:
UTOPIA Level 2 input data. Also known as RX_DATA.
Used by the processor to receive data from an ATM UTOPIA Level 2-compliant
PHY.
•
When an NPE A is configured in UTOPIA Level 2 mode of operation and the
signal is not used, it should be pulled high through a 10-KΩ resistor.
UTP_IP_DATA[5] /
ETHA_COL
MII Mode of Operation:
Asserted by the PHY when a collision is detected by the PHY.
I
Yes
•
When an NPE A is configured in MII mode of operation and the signal is not
used, it should be pulled low through a 10-KΩ resistor.
When this interface is disabled through the UTOPIA Level 2 and/ or the NPE-A
Ethernet soft fuse and is not being used in a system design, it is not required for
®
any connection. Refer to Expansion Bus Controller chapter of the Intel IXP43X
Product Line of Network Processors Developer’s Manual.
UTOPIA Level 2 Mode of Operation:
UTOPIA Level 2 input data. Also known as RX_DATA.
Used by the processor to receive data from an ATM UTOPIA Level 2-compliant
PHY.
MII Mode of Operation:
Asserted by the PHY when transmit medium or receive medium is active. De-
asserted when both the transmit and receive medium are idle. Remains asserted
throughout the duration of collision condition. PHY asserts CRS asynchronously
and de-asserts synchronously with respect to ETHA_RXCLK.
UTP_IP_DATA[6] /
ETHA_CRS
I
Yes
When this interface/signal is enabled and is not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor. When this
interface is disabled through the UTOPIA Level 2 and/or the NPE-A Ethernet soft
fuse and is not being used in a system design, it is not required for any
®
connection. Refer to Expansion Bus Controller chapter of the Intel IXP43X
Product Line of Network Processors Developer’s Manual.
UTOPIA Level 2 Mode of Operation:
UTOPIA Level 2 input data. Also known as RX_DATA.
Used by the processor to receive data from an ATM UTOPIA Level 2-compliant
PHY.
MII Mode of Operation:
Not Used.
UTP_IP_DATA[7]
I
Yes
When this interface/signal is enabled and is not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor. When this
interface is disabled through the UTOPIA Level 2 and/or the NPE-A Ethernet soft
fuse and is not being used in a system design, it is not required for any
®
connection. Refer to Expansion Bus Controller chapter of the Intel IXP43X
Product Line of Network Processors Developer’s Manual.
Receive PHY address bus.
UTP_IP_ADDR[4:0]
I/O
TRI
No
Used by the processor while operating in an MPHY mode to poll and select a
single PHY at any given point of time.
UTOPIA Level 2 Input Data Flow Control Output signal: Also known as the
RX_ENB_N.
In a SPHY configuration, UTP_IP_FCO is used to inform the PHY that the
processor is ready to accept data.
In MPHY configurations, UTP_IP_FCO is used to select those PHY drives that
signals UTP_RX_DATA and UTP_RX_SOC. The PHY is selected by placing the
PHY’s address on the UTP_IP_ADDR and bringing UTP_OP_FCO to logic 1 during
the current clock, followed by the UTP_OP_FCO going to a logic 0 on the next
clock cycle.
UTP_IP_FCO
Yes
When this interface/signal is enabled and is not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor.
®
††
Refer to the Intel IXP43X Product Line of Network Processors Developer’s Manual for information on how to select an
interface.
®
Intel IXP43X Product Line of Network Processors
HDG
40
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
3.8.2
Device Connection
The following example shown in Figure 10 shows a typical interface to an ADSL Framer
via the UTOPIA bus. Notice that depending on the framer used some control signals
might be required which can be derived from the Expansion bus or the GPIO signals.
Figure 10.
UTOPIA Interface Example
Intel® IXP43X
Product Line of
Network
Processors
Control Signals
25 MHz
EX_BUS
Analog Front
End
ATM Layer Device
ADSL Framer
Multi-Channel
AFE
RJ11
UTP_OP_CLK
UTP_OP_FCO
UTP_OP_ADDR[4:0]
TXCLK
TXENB#
TXADDR[4:0]
TXCLAV
TXSOC
UTP_OP_FCI
UTP_OP_SOC
TXDATA[7:0]
UTP_OP_DATA[7:0]
RXENB#
UTP_IP_FCO
UTP_IP_ADDR[4:0]
RXADDR[4:0]
UTP_IP_FCI
RXCLAV
RXSOC
UTP_IP_SOC
UTP_IP_DATA[7:0]
RXDATA[7:0]
AFE
RJ11
UTP_IP_CLK
RXCLK
UTOPIA Level 2
Interface
25 MHz
SDRAM
Local Memory
B4107-005
3.9
HSS Interface
NPE A has an integrated High-Speed Serial (HSS) module, whose primary function is to
provide connectivity between the internal NPE A and the external HSS interface. There
is one HSS port that can directly interface to SLIC/CODEC devices for voice
applications, or serial DSL framers. The HSS ports are software configurable to support
various serial protocols, such as T1/ E1/J1, and MVIP. For a list of supported protocols,
®
see the Intel IXP400 Software Programmer’s Guide.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
41
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
3.9.1
Signal Interface
Table 15.
High-Speed, Serial Interface 0
Pull
Type
Name
HSS_TXFRAME0
HSS_TXDATA0
HSS_TXCLK0
Up
Recommendations
Field
Down
Transmit frame.
I/O
OD
I/O
I/O
I
Yes
Yes
Yes
Yes
Yes
Yes
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor.
Transmit data out. Open Drain Output.
When this interface/signal is enabled and is used or not used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor to Vcc33.
Transmit clock.
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor.
Receive frame.
HSS_RXFRAME0
HSS_RXDATA0
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor.
Receive data input.
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor.
Receive clock.
HSS_RXCLK0
I/O
When this interface/signal is enabled and is not being used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor.
Notes:
1.
2.
3.
Features disabled/enabled by Soft Fuse must be done during the boot-up sequence. A feature cannot be enabled after
being disabled without asserting a system reset.
Features disabled by a specific part number, do not require pull-ups or pull-downs. Therefore, all pins can be left
unconnected.
Features Enabled by a specific part number and required to be Soft Fuse-disabled, as stated in Note 1 alone require pull-
ups or pull-downs in the clock-input signals.
3.9.2
Figure 11 shows a typical interface between the IXP43X network processors and a SLIC
CODEC, through the SSP and HSS ports, and a couple of GPIO signals.
®
Intel IXP43X Product Line of Network Processors
HDG
42
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Figure 11.
HSS Interface Example
Vccp (3.3 V)
10 KΩ
Intel® IXP 43X
Product Line of
Network Processors
External Oscillator
GPIO_0
GPIO_1
Clock derived internally
from 3.6864 MHz
or external oscilator
SSP_EXTCLK
33 MHz
RESET_N INT_N
SSP_SCLK
SSP_SFRM
SSP_TXD
SSP_RXD
CLK
CS_N
D I
DO
Vccp (3.3 V)
SSP Interface
10 KΩ
HSS_TX_FRAME0
HSS_TXDATA0
HSS_TXCLK0
RJ11
DTX
AFE
HSS_RXFRAME0
HSS_RXDATA0
HSS_RXCLK0
FSYNC
RXD
PCLK
Clock derived from
SLIC/CODEC
or external oscilator
SLIC CODEC
HSS Interface
512 KHz to
8.192 MHz
B4108-005
3.10
SSP Interface
The IXP43X network processors have a Synchronous Serial Peripheral Interface (SSP)
®
module. Its primary function is to provide connectivity between the Intel XScale
Processor and an external SSP interface.
The SSP module supports Texas Instruments synchronous serial protocol (SSP)*,
Motorola serial peripheral interface (SPI)* and National Microwire*.
The clock rate can be selected from an internal, 3.6864-MHz source or external source
fed at input pin SSP_EXTCLK. The clock can then be divided down anywhere from
7.2 KHz to 1.84 MHz by setting bits 15:08 in SSP Control Register 0 (SSCR0). For
instructions on the SSP configuration register, refer to the Serial Clock Register (SCR)
®
subsection in the Memory Controller chapter of the Intel IXP43X Product Line of
Network Processors Datasheet.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
43
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
3.10.1
Signal Interface
Table 16.
Synchronous Serial Peripheral Port Interface
Pull
Up/
Down
Type
Field
Name
Recommendations
SSP_SCLK
SSP_SFRM
SSP_TXD
O
O
O
No
No
No
Serial bit clock.
Serial frame indicator.
Transmit data (serial data out).
Receive data (serial data in).
Should be pulled high through a 10-KΩ resistor when not being utilized in the system.
SSP_RXD
I
I
Yes
Yes
External clock input.
SSP_EXTCLK
Should be pulled high through a 10-KΩ resistor when not being utilized in the system.
3.10.2
Device Connection
There are a number of devices available that can interface to SSP or SPI ports, these
can range from RTC (Real-Time Clock), LCD (Liquid Crystal Displays), Digital Thermal
Sensor to Flash memory devices.
flash devices can be used to store board revision, serial numbers, or assembly
SSP port in the IXP43X network processors. For an additional example of SPI interface,
refer to Figure 11, where a SLIC is connected to the SSP and HSS ports.
®
Intel IXP43X Product Line of Network Processors
HDG
44
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Figure 12.
Serial Flash and SSP Port (SPI) Interface Example
Intel® IXP43X Product
Line of Network
Processors
SPI Flash
SSP_SCLK
SSP_SFRM
SSP_TXD
CLK
CS_N
D I
SSP_RXD
DO
SSP_EXTCLK
7.2 KHz
to 3.6864 MHz
SSP Interface
External Oscillator
B4109-003
3.11
PCI Interface
The PCI Controller of the IXP43X network processors is an industry-standard, 32-bit
interface, high-performance bus that operates at 33 MHz(PCI Local Bus Specification,
Rev. 2.2).
General PCI routing guidelines can be found in Section 6.2, “Topology” on page 67. For
detailed information, see the PCI Local Bus Specification, Rev. 2.2.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
45
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
3.11.1
Signal Interface
Table 17.
PCI Controller (Sheet 1 of 2)
Pull
Type
Name
PCI_AD[31:0]
PCI_CBE_N[3:0]
PCI_PAR
Up/
Recommendations
Field
Down
PCI Address/Data bus.
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
When this interface/signal is enabled and is not being used in a system design, the interface/
signal should be pulled high with a 10-KΩ resistor.
PCI Command/Byte Enables.
When this interface/signal is enabled and is not being used in a system design, the interface/
signal should be pulled high with a 10-KΩ resistor.
PCI Parity.
When this interface/signal is enabled and is not being used in a system design, the interface/
signal should be pulled high with a 10-KΩ resistor.
PCI Cycle Frame.
PCI_FRAME_N
PCI_TRDY_N
PCI_IRDY_N
PCI_STOP_N
PCI_PERR_N
PCI_SERR_N
PCI_DEVSEL_N
PCI_IDSEL
When this interface/signal is enabled and is being used or not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor.
PCI Target Ready.
When this interface/signal is enabled and is being used or not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor.
Initiator Ready.
When this interface/signal is enabled and is being used or not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor.
Stop.
When this interface/signal is enabled and is being used or not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor.
Parity Error.
When this interface/signal is enabled and is being used or not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor.
System Error.
When this interface/signal is enabled and is being used or not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor.
Device Select:
When this interface/signal is enabled and is being used or not being used in a system design,
the interface/signal should be pulled high with a 10-KΩ resistor.
Initialization Device Select.
When this interface/signal is enabled and is not being used in a system design, the interface/
signal should be pulled high with a 10-KΩ resistor.
Arbitration Request.
PCI_REQ_N[3:1]
I
When this interface/signal is enabled and is not being used in a system design, the interface/
signal should be pulled high with a 10-KΩ resistor.
Arbitration Request:
PCI_REQ_N[0]
PCI_GNT_N[3:1]
PCI_GNT_N[0]
Notes:
I/O
O
Yes
No
When this interface/signal is enabled and is not being used in a system design, the interface/
signal should be pulled high with a 10-KΩ resistor.
Arbitration Grant.
Arbitration Grant.
I/O
Yes
When this interface/signal is enabled and is not being used in a system design, the interface/
signal should be pulled high with a 10-KΩ resistor.
1.
2.
3.
Features disabled/enabled by Soft Fuse must be done during the boot-up sequence. A feature cannot be enabled after
being disabled without asserting a system reset.
Features disabled by a specific part number, do not require pull-ups or pull-downs. Therefore, all pins can be left
unconnected.
Features enabled by a specific part number — and required to be Soft Fuse-disabled, as stated in Note 1 — only require
pull-ups or pull-downs in the clock-input signals.
®
Intel IXP43X Product Line of Network Processors
HDG
46
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Table 17.
PCI Controller (Sheet 2 of 2)
Pull
Type
Name
Up/
Recommendations
Field
Down
Interrupt A.
PCI_INTA_N
O/D
I
Yes
Yes
When this interface/signal is enabled and is used or not used in a system design, the
interface/signal should be pulled high with a 10-KΩ resistor.
Clock input.
PCI_CLKIN
When this interface/signal is enabled and is not being used in a system design, the interface/
signal should be pulled high with a 10-KΩ resistor.
Notes:
1.
2.
3.
Features disabled/enabled by Soft Fuse must be done during the boot-up sequence. A feature cannot be enabled after
being disabled without asserting a system reset.
Features disabled by a specific part number, do not require pull-ups or pull-downs. Therefore, all pins can be left
unconnected.
Features enabled by a specific part number — and required to be Soft Fuse-disabled, as stated in Note 1 — only require
pull-ups or pull-downs in the clock-input signals.
3.11.2
PCI Interface Block Diagram
While using the IXP43X network processors in Master mode, the PCI module can
interface to up to four PCI cards (devices) at 33 MHz. The limitation is due to load
requirements to maintain signal integrity.
The PCI-to-PCI bridge must be used to address the PCI requirement not to exceed one
load per PCI connector unless it is through a PCI-to-PCI bridge.
The IDSEL signals on the PCI slots can be connected to one of the PCI_AD lines,
preferable to the higher order address signals. Reset support can be accomplished by
using one of the GPIO pins to generate a reset or through an external decoder of the
Expansion bus.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
47
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Figure 13.
PCI Interface
Intel® IXP43X
Product Line of
Network Processors
PCI Bus
PCI Slots
B4110-003
3.11.3
PCI Option Interface
The IXP43X network processors can be used in a design as a host or as an option
device. This section describes how the IXP43X network processors can be connected as
an option device to obtain proper functionality. There are slight differences in the
recommendations described in this document apply, however the design must use the
device pin connections listed in Table 18.
Table 18.
PCI Host/Option Interface Pin Description (Sheet 1 of 3)
Option
Type
Field
Type
Field
Name
Device-Pin Connection
Description
All address/data signals must be
PCI_AD[31:0]
PCI_CBE_N[3:0]
PCI_PAR
I/O
I/O
I/O
I/O
I/O
I/O
PCI Address/Data bus
connected between the two devices.
Connect signals to same pins between
the two devices.
PCI Command/Byte Enables
PCI Parity
Connect signal to same pin between
the two devices.
Connect signal to same pin between
the two devices.
Connect a 10-KΩ pull-up resistor.
PCI_FRAME_N
PCI_TRDY_N
I/O
I/O
I/O
I/O
PCI Cycle Frame
PCI Target Ready
Connect signal to same pin between
the two devices.
Connect a 10-KΩ pull-up resistor.
®
Intel IXP43X Product Line of Network Processors
HDG
48
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Table 18.
PCI Host/Option Interface Pin Description (Sheet 2 of 3)
Option
Type
Field
Type
Field
Name
Device-Pin Connection
Description
Connect signal to same pin between
the two devices.
Connect a 10-KΩ pull-up resistor.
PCI_IRDY_N
PCI_STOP_N
PCI_PERR_N
PCI_SERR_N
PCI_DEVSEL_N
I/O
I/O
I/O
I/O
I/O
I/O
Initiator Ready
Stop
Connect signal to same pin between
the two devices.
Connect a 10-KΩ pull-up resistor.
I/O
I/O
I/O
I/O
Connect signal to same pin between
the two devices.
Connect a 10-KΩ pull-up resistor.
Parity Error
System Error
Device Select
Connect signal to same pin between
the two devices.
Connect a 10-KΩ pull-up resistor.
Connect signal to same pin between
the two devices.
Connect a 10-KΩ pull-up resistor.
Connect one of the higher order PCI
address signals to the Device.
Connect a 10K pull-up resistor to the
Host.
PCI_IDSEL
I
I
I
I
Initialization Device Select
Arbitration Request
On the Option device, these signals are not
used, they should be pulled high with a 10-KΩ
resistor.
Note: The PCI_REQ_N[n] must correspond
to the PCI_GNT_N[n], where n must
be the same number in the square
bracket.
From the Option device, connect output
signal PCI_REQ_N[0] to one of the
PCI_REQ_N[3:0] inputs to the Host.
Note: the PCI_REQ_N[n] must
correspond to the PCI_GNT_N[n],
where n must be the same number in
the square bracket.
PCI_REQ_N[3:1]
Arbitration Request
From the Option device, connect output
PCI_REQ_N[0] to one of the
On the Option device, this signal is an output
and must be connected to one of the
PCI_REQ_N[3:0] inputs to the Host.
Note: The PCI_REQ_N[n] must correspond
to the PCI_GNT_N[n], where n must
be the same number in the square
bracket.
PCI_REQ_N[3:0] inputs to the Host.
PCI_REQ_N[0]
PCI_GNT_N[3:1]
PCI_GNT_N[0]
I
O
O
I
Note: the PCI_REQ_N[n] must
correspond to the PCI_GNT_N[n],
where n must be the same number in
the square bracket.
Connect one of the Host outputs
PCI_GNT_N[3:0] to PCI_GNT_N[0]
input to the Option.
Note: the PCI_GNT_N[n] must
correspond to the PCI_GNT_N[n],
where n must be the same number in
the square bracket.
Arbitration Grant
On the Option device, these signals are not
used, they should be pulled high with a 10-KΩ
resistor.
O
O
Arbitration Grant
Connect one of the Host outputs
PCI_GNT_N[3:0] to PCI_GNT_N[0]
input to the Option.
Note: the PCI_GNT_N[n] must
correspond to the PCI_GNT_N[n],
where n must be the same number in
the square bracket.
On the Option device, this signal is an input
and must be connected to one of the
PCI_GNT_N[3:0] outputs of the Host.
Note: The PCI_REQ_N[n] must correspond
to the PCI_GNT_N[n], where n must
be the same number in the square
bracket.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
49
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Table 18.
PCI Host/Option Interface Pin Description (Sheet 3 of 3)
Option
Type
Field
Type
Field
Name
Device-Pin Connection
Description
Interrupt A
Connect PCI_INTA_N output from the
Option to one of the GPIO input signals
of the Host. The GPIO signal at the
Host must be configure as an input
interrupt level sensitive.
This interrupt is generated from the Option to
one of the GPIO inputs to the Host.
On the Host this signal is not used, it should
be pulled high with a 10-KΩ resistor.
PCI_INTA_N
O/D
O/D
Clock must be connected to both
devices. Trace lengths must be
matched. Use point to point clock
distribution.
PCI_CLKIN
I
I
Clock input
3.11.4
Design Notes
• The IXP43X network processors do not support the 5 V PCI signal interface by
itself. Only the 3.3 V signal interface is supported without signal level conversion;
however, it is possible to interface to 5 V logic while using a voltage level converter.
• The PCI Local Bus Specification, Rev. 2.2 requires that the bus is always parked,
as some device is always driving the AD lines. You must use pull-ups on these
signals. The specification states that the following control lines should be pulled up:
— FRAME_N
— STOP_N
— INTA_N
— TRDY_N
— SERR_N
— INTB_N
— IRDY_N
— PERR_N
— INTC_N
— DEVSEL_N
— LOCK_N
— INTD_N
• The GPIO pins of the IXP43X network processorscan be used by PCI devices on PCI
slots to request an interrupt from the processors’ PCI controller.
• PCI_INTA_N is used to request interrupts to external PCI Masters. This signal is an
open drain and requires a pull-up resistor.
3.12
JTAG Interface
JTAG is the popular name for IEEE standards 1149.1-1990 and 1149.1a-1993, IEEE
Standard Test Access Port and Boundary-Scan Architecture, which provides support
for:
• Board-level boundary-scan connectivity testing
• Connection to software debugging tools through the JTAG interface
• In-system programming of programmable memory and logic devices on the PCB
The interface is controlled through five dedicated test access port (TAP) pins: TDI, TMS,
TCK, nTRST, and TDO, as described in the IEEE 1149.1 standard. The boundary-scan
test-logic elements include the TAP pins, TAP controller, instruction register,
boundary-scan register, bypass register, device identification register, and data-specific
®
registers. These are described in the Intel IXP43X Product Line of Network Processors
Developer’s Manual.
The IXP43X network processors can be controlled during debug through a JTAG
interface to the processor, the debug tools such as the Macraigor Systems Raven*, EPI
Majic*, Wind River Systems* visionPROBE*/ visionICE* or various other JTAG tools
plug into the JTAG interface through a connector.
®
Intel IXP43X Product Line of Network Processors
HDG
50
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
3.12.1
Signal Interface
Table 19.
Synchronous Serial Peripheral Port Interface
Pull
Up/
Down
Type
Field
Name
Recommendations
Test mode select.
JTG_TMS
I
Yes
When the JTAG interface is not being used, the signal must be pulled high using a 10-kΩ
resistor.
Test Input data.
JTG_TDI
JTG_TDO
I
O
I
Yes
O
When the JTAG interface is not being used, the signal must be pulled high using a 10-kΩ
resistor.
Test Output data.
Test Reset.
JTG_TRST_N
Yes
When the JTAG interface is not being used, the signal must be pulled low using a 10-kΩ
resistor.
Test Clock.
JTG_TCK
I
Yes
When the JTAG interface is not being used, the signal must be pulled high using a 10-kΩ
resistor.
3.13
Input System Clock
The IXP43X network processors require a 33.33-MHz reference clock to generate all
internal clocks required including core clock and the various buses running internally
within the system.
3.13.1
Clock Signals
Table 20.
Clock Signals
Type
Field
Name
Description
Source must be a clock input of 33.33-MHz.
Use a series termination resistor, 10 Ω to 33 Ω at the source.
OSC_IN
I
OSC_OUT
O
No connect
3.13.2
Clock Oscillator
clock, connect the clock oscillator output to the OSC_IN pin through a series
termination of 33 Ω as shown in Figure 14. The series termination helps to smooth the
rise and fall edges of the clock and eliminate ringing. Leave the OSC_OUT pin
unconnected.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
51
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Figure 14.
Clock Oscillator Interface Example
3.3 V
OUT
33 KΩ
VDD
ON
OSC_IN
10 KΩ
0.01 µF
33.33 MHz
OSC_OUT
Intel® IXP43X
Product Line of
Network
Processors
B4111-005
3.13.3
Recommendations for Crystal Selection
The parameters that should be considered while selecting the crystal to be used are:
Frequency
33.33 MHz
Operation Mode
Fundamental
Load
18 pF (This is the capacitance value of the discrete component) *Note1
+/- 30 ppm
Capacitance
Frequency
Tolerance
Frequency
stability over
temperature
+/- 50 ppm
Effective Series
20 ohm *Note2
> 100 uW
Resistance (ESR)
Drive level
Note:
1) The capacitance value here does not include stray capacitance. The design has been
simulated to work with load capacitance up to 36pF.
2) This does not include the stray resistance. The design has been simulated to work up
to 40 ohm series resistance.
The Rf and Rs may not needed. Please refer to the crystal vendor datasheet for
recommendation.
®
Intel IXP43X Product Line of Network Processors
HDG
52
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Figure 15.
Recommended circuit design on PCB for crystal oscillator
osc_out
osc_in
RF=1Mohm
xtal
RS
C
C
3.14
Power
The IXP43X network processors have separate power supply domains for the processor
core, DDRII/I SDRAM memory, and input/output peripherals to enable low power
system design.
Table 21.
Power Supply
Nominal
Name
voltage
Description
†
VCC
1.3V
3.3V
1.3-V power supply input pins are used for the internal logic.
VCC33
3.3-V power supply input pins are used for the peripheral (I/O) logic.
1.8V or
2.5V
VCCDDR
VSS
1.8-V or 2.5-V power supply input pins are used for the DDRII/I memory interface.
Ground power supply input pins are used for the 3.3-V, 2.5-V, 1.8-V, and the 1.3-V power
supplies.
GND
5.0V
5-V power supply input pins are used for reference voltage.
Note: 3.3-V power supply input can be used but causes damage to the USB controller if signal
pin is shorted to 5V VBUS.
USB_v5REF
VCCP_OSC
3.3-V power supply input pins are used for peripheral (I/O) logic of the analog oscillator circuitry.
®
3.3V
Require special power filtering circuitry. See the Intel IXP43X Product Line of Network
Processors Datasheet
1.3V
GND
1.3-V power supply input pin. Dedicated for Fuse.
Specialized ground for USB Band Gap.
1.3-V power supply input pins are used for USB PLL.
VCCF
VSSAUBG
®
VCCAUPLL
VCCAUBG
1.3V
3.3V
Requires special power filtering circuitry.See the Intel IXP43X Product Line of Network
Processors Datasheet
3.3-V power supply input pins are used for USB Band Gap
®
Requires special power filtering circuitry. See the Intel IXP43X Product Line of Network
Processors Datasheet
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
53
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Nominal
Name
voltage
Description
†
VCCPUSB
3.3V
1.3V
3.3-V power supply input pins are used for USB IO.
VCCUSBCORE
1.3-V power supply input pins are used for USB IO core.
1.3-V power supply input pins are used for internal logic of the analog phase lock-loop circuitry.
®
VCCA
1.3V
Requires special power filtering circuitry. See the Intel IXP43X Product Line of Network
Processors Datasheet
3.14.1
Decoupling Capacitance Recommendations
It is common practice to place decoupling capacitors between the supply voltages and
ground. Placement can be near the input supply pins and ground, with one 100-nF
capacitor per pin. Additional decoupling capacitors can be place all over the board
every 0.5" to 1.0". This ensures good return path for currents and reduce power surges
and high-frequency noise.
It is also recommended that 4.7-µF to 10-µF capacitors be placed every 2" to 3".
3.14.2
3.14.3
3.14.4
VCC Decoupling
Connect one 100-nF capacitor per each VCC pin. Placement should be as close as
possible to the pin. It is also recommended to place a 4.7-µF capacitor near the device.
Use traces as thick as possible to eliminate voltage drops in the connection.
VCC33 Decoupling
Connect one 100-nF capacitor per each Vcc33 pin. Placement should be as close as
possible to the pin. It is also recommended to place a 4.7-µF capacitor near the device.
Use traces as thick as possible to eliminate voltage drops in the connection.
VCCDDR Decoupling
Connect one 100-nF capacitor per each VCCDDR pin. Placement should be as close as
possible to the pin. It is also recommended to place a 4.7-µF capacitor near the device.
Use traces as thick as possible to eliminate voltage drops in the connection.
3.14.5
3.14.6
Power Sequence
Power sequence is crucial for proper functioning of the IXP43X network processors. For
®
a complete description of power sequencing, see the Intel IXP43X Product Line of
Network Processors Datasheet.
Reset Timing
Proper reset timing is also a crucial requirement for proper functioning of the IXP43X
network processors. There are two reset signal PWRON_RESET_N and RESET_IN_N
which required assertion sequence.
®
For a complete description of their functionality, see the Intel IXP43X Product Line of
Network Processors Datasheet and its section titled Reset Timings. PWRON_RESET_N
is used as a Power Good and RESET_IN_N is used for resetting internal registers.
®
Intel IXP43X Product Line of Network Processors
HDG
54
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
The IXP43X network processors can be configured at reset de-assertion via external,
pull-down resistors on the address expansion bus signals EX_ADDR[23:21]. For a
complete description, see Section 6, “Boot/Reset Strapping Configuration” on page 22.
§ §
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
55
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
4.0
General PCB Guide
4.1
PCB Overview
Beginning with components selection, this chapter presents general PCB guidelines. In
cases where it is too difficult to adhere to a guideline, engineering judgment must be
used. The methods are listed as simple DOs and DO NOT’s.
This chapter does not discuss the functional aspects of any bus, or layout guides for
any interfaced devices.
4.2
4.3
General Recommendations
It is recommended that boards based on the IXP43X network processors employ a PCB
stackup yielding a target impedance of 50 Ω ± 10% with 5 mil nominal trace width.
That is, the impedance of the trace when not subjected to the fields created by
changing current in neighboring traces.
When calculating flight times, it is important to consider the minimum and maximum
impedance of a trace based on the switching of neighboring traces. Using wider spaces
between the traces can minimize this trace-to-trace coupling. In addition, these wider
spaces reduce crosstalk and settling time.
Component Selection
• Do not use components faster than necessary
Clock rise (fall) time should be as slow as possible, as the spectral content of the
waveform decreases
• Use components with output drive strength (slew-rate) controllable if available
• Use SMT components (not through-hole components) as through-hole (leaded)
components have more stub inductance due to the protruding leads.
• Avoid sockets when possible
• Minimize number of connectors
4.4
Component Placement
As shown in Figure 16 on page 57, when placing components, put:
• High-frequency components in the middle
• Medium-frequency around the high-frequency components
• Low-frequency components around the edge of the printed circuit board
®
Intel IXP43X Product Line of Network Processors
HDG
56
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Figure 16.
Component Placement on a PCB
C
O
N
N
E
C
T
Medium Frequency
High Frequency
Components
O
R
Analog Circuit
Low Frequency
PCB
B2264-01
• Place noisy parts (clock, processor, video, and so on.) at least 1.5 – 3 inches away
from the edge of the printed circuit board
• Do not place noisy components close to internal/external cables
— Any loose cables picks up noise and acts as an antenna to radiate that noise
— Be aware of the peak in-rush surge current into the device pins. This surge
current can inject high-frequency switching noise into power planes of the
printed circuit board
• Place high-current components near the power sources
• Do not share the same physical components (such as buffers and inverters)
between high-speed and low-speed signals. Use separate parts.
• Place clock drivers and receivers such that clock trace length is minimized
• Place clock generation circuits near a ground stitch location. Place a localized
ground plane around the clock circuits and connect the localized plane to system
ground plane
• Install clock circuits directly on the printed circuit board, not on sockets
• Clock crystals should lie flat against the board to provide better coupling of
electromagnetic fields to the board
4.5
Stack-Up Selection
Stack-up selection directly affects the trace geometry which, in turn, affects the
characteristic impedance requirement for the printed-circuit board. Additionally, the
clean, noise-free-planes design and placement is significantly important as
components run at higher speeds requiring more power.
Considerations include:
• Low-speed, printed-circuit-board construction — for example two-layer boards:
— Advantages:
• Inexpensive
• Manufactured by virtually all printed-circuit-board vendors
— Disadvantages:
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
57
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
• Poor routing density
• Uncontrolled signal trace impedance
• Lack of power/ground planes, resulting in unacceptable crosstalk
• Relatively high-impedance power distribution circuitry, resulting in
noise on the power and ground rails
• High-speed circuits require multi-layer printed circuit boards:
— Advantages:
• Controlled-impedance traces
• Low-impedance power distribution
— Disadvantages:
• Higher cost
• More weight
• Manufactured by fewer vendors
• Symmetry is essential to keep the board stack-up symmetric about the center
This minimizes warping
• For best impedance control, have:
— No more than two signal layers between every power/ground plane pair
— No more than one embedded micro-strip layer under the top/bottom layers
• For best noise control, route adjacent layers orthogonally. Avoid layer-to-layer
parallelism
• Fabrication house must agree on design rules, including:
— Trace width, trace separation
— Drill/via sizes
• The distance between the signal layer and ground (or power) should be minimized
to reduce the loop area enclosed by the return current
— Use 0.7:1 ratio as a minimum.
Figure 17 and Figure 18 provides an example for a six-layer and eight-layer board. For
stripline (signals between planes), the stackup should be such that the signal line is
closer to one of the planes by a factor of five or more. Then the trace impedance is
controlled predominantly by the distance to the nearest plane.
®
Intel IXP43X Product Line of Network Processors
HDG
58
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Figure 17.
8-Layer Stackup
4.5 mil
5 mil
7 mil
Legend
Component (Top) Side
SIGNAL
Data
Data
Data
L1
L2
L3
L4
GND
17.8 mil
7 mil
5 mil
4.5 mil
62 mil
POWER
Data
Data
L5
L6
L7
L8
Solder (Bottom) Side
B2244-02
Figure 18.
6-Layer Stackup
Legend
4.5 mil
SIGNAL
GND
7 mil
Component (Top) Side
L1
~40 mil
L2
L3
7 mil
62 mil
POWER
4.5 mil
L4
L5
L6
Solder (Bottom) Side
B2275-02
• Fast and slow transmission line networks must be considered
• PCB-board velocities
• Board FR4 ~ 4.3
• Target impedance of 50 Ω ± 10%
• Trace width: 5 mils
• Signal Layers (1/2 oz. Copper)
• Power Layer (1 oz. Copper)
• Ground (GND) Layer (1 oz. Copper)
§ §
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
59
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
5.0
General Layout and Routing Guide
5.1
Overview
This chapter provides routing and layout guides for hardware and systems based on the
IXP43X network processors.
The high-speed clocking required when designing with the processors requires special
attention to signal integrity. In fact, it is highly recommended that the board design be
simulated to determine optimum layout for signal integrity. The information in this
chapter provides guidelines to aid designers with board layout. In cases where it is too
difficult to follow a design rule, engineering judgment must be used.
5.2
General Layout Guidelines
The layout guidelines recommended in this section are based on experience and
knowledge gained from previous designs. Layer stacking varies, depending on design
complexity, however following standard rules helps minimize potential problems
dealing with signal integrity.
The following recommendations help to route a functional board:
• Provide enough routing layers to comply with minimum and maximum timing
requirements of the IXP43X network processors and other components.
• Connectors, and mounting holes must be placed in a ways that will not interfere
with basic design guidelines in this document.
• Provide uniform impedance throughout the board, specially for high speed areas
such us clocking, DDRII/I-SDRAM, PCI, device bus, and so forth.
• Place analog, high-voltage, power supply, low-speed, and high-speed devices in
various sections of the board.
• Decoupling capacitors must be placed next to power pins.
• Series termination resistors must be placed close to the source.
• Analog and digital sections of the board must be physically isolated from each
other. No common ground, power planes, and signal traces are allowed to
cross-isolation zones. Use appropriately sized PCB traces for larger enough to
handle peak current. Keep away from high-speed digital signals.
• Keep stubs as short as possible (preferably, the electrical length of the stub less
than half of the length of the rise time of signal).
• All critical signals should be routed before all other non-critical signals.
• Do not route signals close to the edge of the board, power or ground planes. Route
signal at least 50 to 100 mils away from the edge of the plane.
• Try to match buses to the same trace length and keep them in groups adjacent to
each other, away from other signals.
• Route processor address, data and control signals using a daisy-chain topology.
• Minimize number of vias and corners on all high speed signals.
• Do not route under crystals or clock oscillators, clock synthesizers, or magnetic
devices (ferrites, toroids).
• Maintain trace spacing consistent between differential pairs and match trace length.
• Keep differential signals away from long and parallel, high-speed paths, such as
clock signals and data strobe signals.
®
Intel IXP43X Product Line of Network Processors
HDG
60
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
• Do not place high-frequency oscillators and switching network devices close to
sensitive analog circuits.
• Arrange the board so that return currents for high-speed traces must never jump
between planes. Restrict traces to remain on either side of whichever ground plane
they start out nearest. This allows the use of naturally grouped horizontal and
vertical routing layers.
If signals change between layers, the reference voltage changes, as shown in
Figure 19. This creates discontinuity in the path of the signal.
Figure 19.
Signal Changing Reference Planes
VIAs
Driver
Signal
Receiver
Signal
GND
PWR
Return Current
ByPass Caps
Trace
Signal
B2269-01
The design in Figure 19, routes a signal on the top layer, close to the GND plane, and
provides a very good return current path. The signal then is routed to the bottom layer,
close to the PWR plane, such that the return current flows to the ground plane through
bypass caps. Thus the path for the return currents is less inductive than in the previous
case where the signal is routed on the top layer.
5.2.1
General Component Spacing
• Do not place components within 125 mils to the edge of the printed circuit board.
For exact dimensions consult your manufacturing vendor.
• Keep a minimum spacing between via and the solder pad edges > 25mil.
• Position devices that interface with each other close to one another to minimize
trace lengths.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
61
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Figure 20.
Good Design Practice for VIA Hole Placement
25 mils min
25 mils min
25 mils min
B2266-01
surface-mount boards.
Figure 22 shows minimum pad-to-pad clearance for surface-mount passive
components and PGA or BGA components.
Figure 21.
Poor Design Practice for VIA Placement
Flush Via min
Potential Bridge min
B2267-01
®
Intel IXP43X Product Line of Network Processors
HDG
62
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Figure 22.
Pad-to-Pad Clearance of Passive Components to a PGA or BGA
PBGA Package
60 mils min
60 mils min
60 mils min
B2268 -01
5.2.2
Clock Signal Considerations
• Provide good return current paths for clock traces.
• Keep clock traces away from the edge of the board and any other high-speed
devices or traces.
• Keep clock traces away from analog signals, including voltage reference signals.
• Clock signals should not cross over a split plane.
• Route clock signals in a single, internal layers and eliminate routing in multiple
layers as much as possible.
• Do not route traces or vias under crystals or clock oscillators devices unless there is
a plane between the trace and the component.
• Do not route parallel signal traces directly above or below clock traces unless there
is a ground or at least a power plane separation between those layers.
• Route clock traces with a minimum number of vias.
• Space clock traces away from other signals three times the trace width on each
side.
• Use guard traces when routing on top or bottom layers whenever possible. Guard
traces must be connected to ground.
• Do not daisy-chain, instead use point-to-point clock distribution. Place a series
termination resistor as close as possible to the source.
• Keep traces short to minimize reflections and signal degradation.
• Maintain control impedance for all clock traces, microstrip or stripline.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
63
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
— Be aware of propagation delays between a microstrip and stripline.
— Calculate capacitive loading of all components and properly compensate with a
series or parallel terminations.
• Measure and match trace lengths for devices that interface with each other and
have their clock derived from the same source.
If traces must be long, treat them as transmission lines. Terminate clock traces to
match trace impedance.
• If there is a power plane, instead of a ground plane, make sure that the power
plane has adequate decoupling to ground, especially near clock drivers and
receivers.
5.2.3
5.2.4
MII Signal Considerations
MII signals run at 25 MHz and the required routing guide lines are as follows:
• Minimize the number of vias to two per trace
• Keep traces as short as possible and straight, away from other signals
• Control impedance to maintain at 50 Ω
• the length of Rx or Tx in each group must match
• Avoid sharp corners, using 45° corners instead
USB V2.0 Considerations
The following are recommendations for routing differential pair signal required to by
the USB interface:
• Traces can be routed in tightly couple structure with 5mil trace width and 10mil air
gap, or maintain air gap equal 2X trace width. It is recommended to route
manually.
• Match trace length for each differential pair.
• Avoid sharp corners, use 45° corners instead.
• Always use a perfect symmetry within a differential pair.
• Minimize the number vias.
• Avoid routing other signals close by or in parallel to the differential pair,
maintaining no less than 50 mil to any other signal.
• Maintain control impedance for each differential pair to 90 Ω +/- 15 Ω.
• Use high value ferrite beads (100 MHz/60 Ω – 100 MHz/240 Ω).
5.2.5
Crosstalk
Crosstalk is caused by capacitance and inductance coupling between signals. It is
composed of both backward and forward crosstalk components.
Backward crosstalk creates an induced signal on the network that propagates in the
opposite direction of the aggressor signal. Forward crosstalk creates a signal that
propagates in the same direction as the aggressor signal.
Circuit board analysis software should be used to analyze your board layout for
crosstalk problems.
• To effectively route signals on the PCB, signals are grouped (address, data, and so
on.).
— The space between groups can be 3 w (where w is the width of the traces).
®
Intel IXP43X Product Line of Network Processors
HDG
64
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
— Space within a group can be just 1 w.
— Space between clock signals or clock to any other signal should be 3 w. The
coupled noise between adjacent traces decreases by the square of the distance
between the adjacent traces.
5.2.6
EMI Design Considerations
It is strongly recommended that good electromagnetic interference (EMI) design
practices must be followed while designing with the IXP43X network processors.
®
• Information on spread-spectrum clocking is available in the Intel IXP4XX Product
Line of Network Processors and IXC1100 Control Plane Processor: Spread-
Spectrum Clocking to Reduce EMI Application Note.
• Place high-current devices as closely as possible to the power sources.
• Proper termination of signals can reduce reflections, which can emit a high-
frequency component that contribute to more EMI than the original signal itself.
• Ferrite beads can be used to add high frequency loss to a circuit without
introducing power loss at DC and low frequencies. They are effective when used to
absorb high-frequency oscillations from switching transients or parasitic
resonances within a circuit.
• Keep rise and fall times as slow as possible. Signals with fast rise and fall times
contain many high-frequency harmonics which can radiate significantly.
• A solid ground is essential at the I/O connector to chassis and ground plane.
• Keep the power plane shorter than the ground plane by at least 5x the spacing
between the power and ground planes.
• Stitch together all ground planes around the edge to the board every 100 to
200 mil. This helps reduce EMI radiating out of the board from inner layers.
5.2.7
5.2.8
Trace Impedance
All signal layers require controlled impedance of 50 Ω ±10 % microstrip or stripline
(unless otherwise specified) where appropriate. Selecting the appropriate board stack-
up to minimize impedance variations is very important.
When calculating flight times, it is important to consider the minimum and maximum
trace impedance based on the switching neighboring traces.
Power and Ground Plane
Power and ground planes should have sufficient decoupling capacitors to ensure
sustainable current needed for high-speed switching devices. See Section 3.14.1,
“Decoupling Capacitance Recommendations” on page 54.
• It is highly recommended to use sufficient internal power and ground planes.
®
• The Intel IXP43X Product Line requires a number of power supplies. It is
appropriate to use power islands in the power plane under the processor, as it will
be too expensive to have a power plane for each power source.
• Power islands must be large enough to include the required power supply
decoupling capacitance, and the necessary connection to the voltage source and
destination.
• Islands can be separated by a minimum of 20-mil air gap.
• Use at least one via per power or ground pin, wherever possible use more vias,
depending on current drawn.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
65
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
• Use at least one decoupling capacitor per power pin and place it as close as
possible to the pin.
• Minimize the number of traces routed across the air gaps between power islands.
— Each crossing introduces signal degradation due to the impedance
discontinuity.
— For traces that must cross air gaps, route them on the side of the board next to
a ground plane to reduce or eliminate signal degradation caused by crossing
the gap.
— When this is not possible, then route the trace to cross the gap at a right angle
(90°).
§ §
®
Intel IXP43X Product Line of Network Processors
HDG
66
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
6.0
PCI Interface Design Considerations
The IXP43X network processors have a single, 32-bit PCI device module that runs at 33
MHz. This chapter describes some basic guidelines to help design hardware that
interfaces with PCI devices.
The PCI module is compatible with the PCI Local Bus Specification, Rev. 2.2. For a
complete functional description and physical requirements, see the PCI Local Bus
Specification, Rev. 2.2.
6.1
6.2
Electrical Interface
The electrical definition is restricted to 3.3 V signaling environment. The device is not
5 V tolerant. All devices interfacing with the PCI module must operate at 3.3 V.
Topology
Interfacing devices must be connected in a daisy-chain topology. When more than one
device is in the bus, connecting stubs must be kept as short as possible.
There is a limitation to the number of devices connected to the internal arbiter. If more
than four devices are required to be connected, an external arbiter is required.
and timing parameters must be met while routing a board that interfaces with a single
PCI device or up to four devices as shown in Figure 23.
TCYC ≥ TVAL +TPROP + TSKEW + TSU
where:
TVAL = Valid Output Delay
TPROP = Bus Propagation Delay (maximum time for complete flight)
TSKEW = Total Clock Skew
TSU = Input Setup Time
@33 MHz
TCYC = 30 nSec
TVAL = 11 nSec
TPROP = 10 nSec
TSKEW = 2 nSec
When defining the maximum length of segments A and B as shown in Figure 23, the
calculation must:
• Include an additional trace length segment from the PCI connector to the input
device within the expansion PCI card
• Assume the segment to be 1.5 inch
• Use trace propagation delay of 150 to 190 ps/in as specified by the PCI standard
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
67
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Figure 23.
PCI Address/Data Topology
Intel® IXP43X
Product Line of
Network
PCI Slot
PCI Slot
PCI Slot
PCI Slot
Processors
A
B
B
B
B5196-003
Table 22.
PCI Address/Data Routing Guidelines
Parameter
Routing Guidelines
Signal Group
PCI Address/Data
Daisy Chain
Ground
Topology
Reference Plane
Characteristic Trace Impedance
Nominal Trace Width
55 Ω ±10%
5 mils
Nominal Trace Separation
Spacing to Other Groups
Limit the number of VIAS to 10 per Signal
10 mils
20 mils
10
6.3
Clock Distribution
To meet timing and avoid clock overloading, it is recommended to use point-to-point
clock distribution as shown in Figure 24.
Clock skew between interfacing devices is very critical and must be met. The maximum
skew must be measured between any two components. If designing a motherboard,
the skew must be measured to the expansion card device and not to the PCI connector.
Ensure that clock skew between all devices does not exceed the values in Section 6.2.
®
Intel IXP43X Product Line of Network Processors
HDG
68
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Figure 24.
PCI Clock Topology
PCI Devices
A
A
B
B
Rs
Rs
Clock
Driver
33 MHz
Intel®
IXP43X
A
Product Line
of Network
Processors
B
Rs
B4114-004
Table 23.
PCI Clock Routing Guidelines
Parameter
Routing Guidelines
Signal Group
PCI Clock
Topology
Point-to-Point
Ground
Reference Plane
Characteristic Trace Impedance
Nominal Trace Width
Nominal Trace Separation
Spacing to Other Groups
Trace length A
55 Ω ±10%
5 mils
10 mils
20 mils
Maximum 300 mils
There is no limit as long as the trace length is maintained for
each clock and that maximum clock skew is not violated.
Trace length B
Resistor Rs
22 Ω ±10%
Maximum VIAS
6
6.3.1
Trace Length Limits
intended to run. The limitations of the maximum trace length can be calculated with
the equations shown in Section 6.2. Solve for TPROP and use it to calculate the maximum
trace length. This is a straight-forward calculation, but very critical to meet timing. It is
recommended to keep the trace lengths as short as possible and not to exceed TPROP
.
Note:
For acceptable signal integrity at up to 33 MHz, it is very important to design the PCB
board with controller impedance in the range of 55 Ω ±10%.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
69
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
6.3.2
Routing Guidelines
It is recommended to route signals with respect to an adjacent ground plane. If routing
signals over power planes, ensure that the signals are referenced to a single power
plane voltage level and not multiple levels. For example, you can route signals over a
3.3 V plane or a 5 V plane, but do not route the same signal over both planes. If signals
are routed over split planes, you must connect the splitting planes with 0.01 µF,
high-speed capacitors near the signal crossing the split. The capacitors should not be
placed more than 0.25 inches from the point at which the signals cross the split.
This manual does not repeat all the guidelines that are already stated in the
PCI Local Bus Specification, Rev. 2.2. Refer to the specification when designing a
motherboard or an expansion card.
6.3.3
Signal Loading
Shared PCI signals must be limited to one load on each of the PCI slots. Any violation of
expansion board or add-on device trace length or loading limits compromises
system-signal integrity.
§ §
®
Intel IXP43X Product Line of Network Processors
HDG
70
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
7.0
DDRII / DDRI SDRAM
7.1
Introduction
This document is intended to be used as a guide for routing DDRII/DDRI SDRAM based
®
on the Intel IXP435 Multi-Service Residential Gateway Reference Platform. It contains
routing guidelines and simulation results for using x16 Thin Small Outline Package
(TSOP) memory devices soldered onto the processor module.
The memory controller only corrects single bit ECC errors on read cycles. The ECC is
stored into the DDRII/DDRI SDRAM array along with the data and is checked when the
data is read. If the code is incorrect, the MCU corrects the data before reaching the
initiator of the read. ECC error scrubbing is done with software. User-defined fault
correction software is responsible for scrubbing the memory array and handling double-
bit errors.
To limit double-bit errors from occurring, periodically read the entire usable memory
array to allow the hardware unit within the memory controller to correct any single-bit.
This also prevents the ECC errors that would have occurred prior to these errors
becoming double-bit ECC errors. Implementing this method is system-dependent.
Note:
It is important to note that when sub-word writes (byte writes or half-word writes
within a word-aligned boundary) are done to a 32-bit memory with ECC enabled, the
memory controller performs read-modify writes. There is a performance impact with
read-modify writes that must be considered when writing software.
With read-modify writes, the memory controller reads the 32-bit word that
encompasses the byte that is to be written when a byte write is requested. The
memory controller modifies the specified byte, calculates a new ECC, and writes the
entire 32-bit word back into the memory location it was read from.
The value written back into the memory location contains the 32-bit word with the
modified byte and the new ECC value.
The MCU supports two physical banks of DDRII/DDRI SDRAM. The MCU has support for
unbuffered DDRI 266 and DDRII 400 in the form of discrete chips only.
The MCU supports a memory subsystem ranging from 32 MB to 1 GB for 32-bit
memory systems for DDRI SDRAM, from 64 MB to 512 MB for 32-bit memory systems
for DDRII SDRAM, and supports 16 MB for 16-bit memory systems for DDRI SDRAM
ECC or non-ECC system can be implemented using x8, or x16 devices. Table 25,
Table 26, Table 27 and Table 28 illustrate the supported DDRII/DDRI SDRAM
configurations
The two DDRII/DDRI SDRAM chip enables (DDR_CS_N[1:0]) support a DDRII/DDRI
SDRAM memory subsystem consisting of two banks. The base address for the two
contiguous banks are programmed in the DDRII/DDRI SDRAM Base Register (SDBR)
and is aligned to a 16 MB boundary. The size of each DDRII/DDRI SDRAM bank is
programmed with the DDRII/DDRI SDRAM boundary registers (SBR0 and SBR1).
The DDRII/DDRI SDRAM devices comprise four internal leaves. The MCU controls the
leaf selects within DDRII/DDRI SDRAM by toggling DDR_BA[0] and DDR_BA[1].
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
71
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Table 24.
DDRII/I Signal Groups
Group
Signal Name
Description
D_CK[2:0] / DDR_CK[2:0] DDRII/I SDRAM Differential Clocks
Clocks
D_CK_N[2:0] /
DDRII/I SDRAM Inverted Differential Clocks
DDR_CK_N[2:0]
D_CB[7:0] / DDR_CB[7:0] ECC Data
D_DQ[31:0] /
Data Bus
DDR_DQ[31:0]
D_DQS[4:0] /
Data Strobes
DDR_DQS[4:0]
Data
D_DQS_N[4:0]
Complementary Data Strobes
Data Mask
D_DM[4:0] /
DDR_DM[4:0]
D_CKE[1:0] /
DDR_CKE[1:0]
Clock Enable - one per bank
Chip Select - one per bank
Address Bus
Control
D_CS_N[1:0] /
DDR_CS_N[1:0]
D_MA[13:0] /
DDR_MA[13:0]
D_BA[1:0] / DDR_BA[1:0] Bank Select
Command
D_RAS_N / DDR_RAS_N
D_CAS_N / DDR_CAS_N
D_WE_N / DDR_WE_N
Row Address Select
Column Address Select
Write Enable
®
Intel IXP43X Product Line of Network Processors
HDG
72
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Figure 25.
Processor-DDRII/I SDRAM Interface
DDRII/I_DQ[31:0]
DDRII/I_MA[13:0]
DATA[31:0]
DQ[31:0]
A[13:0]
ADDRESS[13:0]
CLOCK[2:0], CLOCK#[2:0]
CLOCK ENABLE[1:0]
CHIP SELECT#[1:0]
DDRII/I_CK[2:0]
DDRII/I_CK_N[2:0]
CK[2:0]
CK#[2:0]
DDRII/I_CKE[1:0]
DDRII/I_CS_N[1:0]
DDRII/I_BA[1:0]
CKE[1:0]
CS#[1:0]
BA[1:0]
BANK SELECT[1:0]
DDRII/I_CB[7:0]
DDRII/I_DM[4:0]
ECC DATA[7:0]
DQ[7:0]
DM[4:0]
DATA MASK[4:0]
DDRII/I_DQS[4:0]
DATA STROBE[4:0]
WRITE#, RAS#, CAS#
DQS[4:0]
WE#
RAS#
CAS#
DDRII/I_WE_N
DDRII/I_RAS_N
DDRII/I_CAS_N
B3986-003
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
73
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Table 25.
Supported DDRI 32-bit SDRAM Configurations
Address Size
Leaf Select
Total
DDR SDRAM
Technology
DDR SDRAM
Arrangement
Page
# Banks
Memory
b
Size
a
Row
Column
DDR_BA[1]
DDR_BA[0]
ADDR[25]
Size
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
64 M
128 M
32 M
4KB
4KB
2KB
2KB
4KB
4KB
2KB
2KB
8KB
8KB
4KB
4KB
8KB
8KB
4KB
4KB
16 M x 8
8 M x 16
32 M x 8
16 M x 16
64 M x 8
32 M x 16
128 M x 8
64 M x 16
12
10
ADDR[26]
ADDR[25]
ADDR[27]
ADDR[26]
ADDR[28]
ADDR[27]
ADDR[29]
ADDR[28]
c
128 Mbit
12
13
13
13
13
14
14
9
ADDR[24]
ADDR[26]
ADDR[25]
ADDR[27]
ADDR[26]
ADDR[28]
ADDR[27]
64 M
128 M
256 M
64 M
10
9
256 Mbit
512 Mbit
128 M
256 M
512 M
128 M
256 M
512 M
1 G
11
10
11
10
c
1 Gbit
256 M
512 M
a. Table indicates 32-bit wide memory subsystem sizes.
b. Table indicates 32-bit wide memory page sizes.
c. Supported with DDR SDRAM only
Table 26.
Supported DDRII 32-bit SDRAM Configurations
Address Size
Row Column
Leaf Select
Total
Memory
Size
DDR SDRAM
Technology
DDR SDRAM
Arrangement
# of
Banks
Page
Size
DDR_BA[1]
DDR_BA[0]
1
2
1
2
1
2
1
2
128MB
256MB
64MB
4KB
4KB
2KB
2KB
4KB
4KB
4KB
4KB
32M x 8
16M x16
64M x 8
32M x16
13
13
14
13
10
9
ADDR[27]
ADDR[26]
256 Mbit
ADDR[26]
ADDR[28]
ADDR[27]
ADDR[25]
ADDR[27]
ADDR[26]
128MB
256MB
512MB
128MB
256MB
10
10
512 Mbit
Table 27.
Supported DDRI 16-bit SDRAM Configurations
Address Size
Leaf Select
Total
Memory
Size
DDR SDRAM
Technology
DDR SDRAM
Arrangement
# of
Banks
Page
Size
Row
Column
DDR_BA[1]
DDR_BA[0]
128 Mbit
8M x16
1
12
9
ADDR[23]
ADDR[22]
16MB
1KB
®
Intel IXP43X Product Line of Network Processors
HDG
74
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Table 28.
Supported DDRII 16-bit SDRAM Configurations
Address Size
Leaf Select
Total
Memory
Size
DDR SDRAM
Technology
DDR SDRAM
Arrangement
# of
Banks
Page
Size
DDR_BA[1
]
Row
13
Column
DDR_BA[0]
256 Mbit
16M x16
1
9
ADDR[24]
ADDR[23]
32MB
The DDR_RCOMP signal must be terminated through resistors specified in Figure 26.
This allows the DDRII/I controller to make temperature and process adjustments.
7.2
DDRII/DDRI RCOMP and Slew Resistances Pin
Figure 26 shows the requirements for the DDRII/DDRI RCOMP pin.
Figure 26.
DDRII/DDRI RCOMP Pin External Resistor Requirements
DDRI
R1 =387Ω ±1%
resistor
OR
DDRII
R 1 =285Ω ±1 % resistor
DDRIMPCRES
R1
R2
Intel® IXP43X
Product Line of
Network Processors
DDRCRES
0
DDRSLWCRES
DDRI
R2 =845Ω ±1% resistor
OR
DDRII
R 2 =825Ω ±1 % resistor
For example, when DDRI SDRAM is used, DDRIMPCRES is connected with 387Ω and
DDRSLWCRES is connected with 845Ω resistor to DDRCRES0.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
75
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
7.3
Figure 27 shows the requirement for the DDRRES1 and DDRRES2 pins.
Figure 27.
DDRII OCD Pin Requirements
DDRRES2
Intel® IXP43X
Product Line
of Network
Processors
DDRRES1
0. 1 uF
1 K
Ω
40.2
resistor
Ω
resistor
Note:
Since the OCD calibration function is not enabled, DDRRES2 must be pulled to ground
with a 1-KΩ resistor.
7.3.1
Signal-Timing Analysis
Figure 28.
DDR Clock Timing Waveform
V
V
tch
tcl
V
ih(min)
V
ih (min)
V
test
V
test
V
V
V
il(max )
il(max)
il(max )
T
CH
T
CL
T
C
Table 29.
DDR Clock Timings
DDR-II 400
DDR-I 266
Symbol
Parameter
Units
Notes
Min
Max
Min
Max
T
DDR SDRAM clock Frequency
DDR SDRAM clock Cycle Time
DDR SDRAM clock High Time
DDR SDRAM clock Low Time
200
133
MHz
ns
F
T
5
7.5
1
1
1
C
T
2.15
2.15
3.37
3.37
ns
CH
T
ns
CL
T
DDR SDRAM clock Period Stability
350
100
350
100
ps
CS
DDR SDRAM clock skew for any
differential clock pair (D_CK[2:0] -
T
ps
skew
Notes:
1.
2.
See Figure 28, “DDR Clock Timing Waveform” on page 76
Vtest is nominally (0.5 * Vtch - Vtcl)
®
Intel IXP43X Product Line of Network Processors
HDG
76
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Figure 29.
DDR SDRAM Write Timings
TVA3
ADDR/CTRL
TVB3
TVA5
CS[1:0]#
TVB5
CK
DQS
DQS#
T VA1
TV7
TVB1
DQ
Figure 30.
DDR SDRAM Read Timings
DQS
TVB4
TVA4
DQ
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
77
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Figure 31.
DDR - Write Preamble/Postamble Duration
TVB6
DQS
TVA6
DQS
Table 30.
DDRII-400 MHz Interface -- Signal Timings
Symbol
Parameter
Minimum
Nominal
Maximum
Units
Notes
T
T
DQ, CB and DM write output valid time before DQS.
DQ, CB and DM write output valid time after DQS.
521
521
ps
ps
1
1
VB1
VA1
Address and Command write output valid before CK
rising edge.
T
T
T
T
1771
1771
323
ps
ps
ps
ps
1, 4
1, 4
2
VB3
VA3
VB4
VA4
Address and Command write output valid after CK rising
edge.
DQ, CB and DM read input valid time before DQS rising
or falling edges.
DQ, CB and DM read input valid time after DQS rising or
falling edges.
323
2
T
T
T
T
CS_N[1:0] control valid before CK rising edge.
CS_N[1:0] control valid after CK rising edge.
DQS write preamble duration.
1771
1771
ps
ps
ps
ps
ps
4
4
3
3
1
VB5
VA5
VB6
VA6
3750
2500
1750
DQS write postamble duration.
T
V7
Notes:
1.
2.
See Figure 29, “DDR SDRAM Write Timings” on page 77
See Figure 30, “DDR SDRAM Read Timings” on page 77. The specified minimum requirements for the “Data to strobe
read setup” and “Data from strobe read hold” are determined with the DQS delay programmed for 90 degree phase
shift.
3.
4.
5.
See Figure 31, “DDR - Write Preamble/Postamble Duration” on page 78
Address/Command pin group; RAS_N, CAS_N, WE_N, MA[13:0], BA[1:0]
Designed to JEDEC specification; it is recommended that IBIS models should be used to verify signal integrity on
individual designs
®
Intel IXP43X Product Line of Network Processors
HDG
78
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Table 31.
DDR II/I SDRAM Interface -- Signal Timings
Symbol
Parameter
Minimum
Nom.
Maximum
Units
Notes
DQ, CB and DM write output valid time
before DQS.
T
T
T
T
T
T
T
1146
ps
1
VB1
VA1
VB3
VA3
VB4
VA4
VB5
DQ, CB and DM write output valid time after
DQS.
1146
3021
3021
948
ps
ps
ps
ps
ps
ps
1
1, 4
1, 4
2
Address and Command write output valid
before CK rising edge.
Address and Command write output valid
after CK rising edge.
DQ, CB and DM read input valid time before
DQS rising or falling edges.
DQ, CB and DM read input valid time after
DQS rising or falling edges.
948
2
CS_N[1:0] control valid before CK rising
edge.
3021
3021
4
T
T
T
CS_N[1:0] control valid after CK rising edge.
DQS write preamble duration.
ps
ps
ps
ps
4
3
3
1
VA5
VB6
VA6
5625
3750
1750
DQS write postamble duration.
T
V7
Notes:
1.
2.
See Figure 29, “DDR SDRAM Write Timings” on page 77
strobe read setup” and “Data from strobe read hold” are determined with the DQS delay programmed for
90 degree phase shift.
3.
4.
5.
See Figure 31, “DDR - Write Preamble/Postamble Duration” on page 78
Address/Command pin group; RAS_N, CAS_N, WE_N, MA[13:0], BA[1:0]
Designed to JEDEC specification; it is recommended that IBIS models should be used to verify signal
integrity on individual designs
7.3.1.0.1
Printed Circuit Board Layer Stackup
®
The layer stackup used for the Intel IXP435 Multi-Service Residential Gateway
Reference Platform is a 6-layer, printed circuit board with four signal layers and two
plane layers.
Details on the voltage reference layout are available in the CAD database or Gerber
®
files database for the Intel IXP435 Multi-Service Residential Gateway Reference
Platform.
7.3.2
Timing Relationships
The routing guidelines presented in the following subsections define the recommended
routing topologies, trace width, spacing geometries, and typical routed lengths for each
signal group. These parameters are recommended to achieve optimal signal integrity
and timing.
All signal groups are length matched to the DDR clocks. The clocks on the processor
module are length matched to within ±10 mils of each other. Once this overall clock
signals can be routed to within the timing specified. A simple summary of the timing
results for each signal group is provided in Table 32 on page 80.
Control/Command Group to Clock Summary:
• The maximum allowable difference from any command/control signal to the clock is
±0.6 ns.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
79
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
— Table 31 on page 79
Data Group to Strobe Summary:
• The more restrictive data group to strobe timing occurs for read operations
— Table 32 on page 80
— Table 33 on page 80
±0.25 ns.
— Figure 30 on page 77
— Table 32 on page 80
Strobe to Clock Summary:
0.475 ns to +0.875 ns
— Figure 32 on page 83
— Table 34 on page 83
These are absolute maximum ratings for length mismatch based in ideal printed board
conditions (exact signal propagation delays, ideal signal integrity with no reflections or
settling, zero rise/fall times, and so on.). To compensate for these non-ideal conditions,
more restrictive length matching conditions should be used based on signal integrity
analysis and simulation to provide a buffer zone and avoid possible variations in silicon
or printed circuit board manufacture.
Table 32.
Timing Relationships
Signal Group
Absolute Minimum Length
Absolute Maximum Length
Control to Clock
Command to Clock
Data to Strobe
Clock – 600 ps
Clock – 600 ps
Strobe – 250 ps
Clock – 475 ps
Clock + 600 ps
Clock + 600 ps
Strobe + 250 ps
Clock + 875 ps
Strobe to Clock
In addition to any trace length differentials which must be considered between signal
groups, differences in the package length between signals should be considered when
determining the total propagation delay of the signals. When using the IXP435
reference platform IBIS model for signal analysis, package characteristics are included
in the simulation results.
Table 33.
Signal Package Lengths (Sheet 1 of 3)
Group
Signal Name
Length (mil)
Signal Name
Length (mil)
D_CK_N0 /
DDR_CK_N0
558.19
D_CK0 / DDR_CK0
507.46
D_CK_N1 /
DDR_CK_N1
Clock
385.12
504.20
D_CK1 / DDR_CK1
D_CK2 / DDR_CK2
385.12
548.01
D_CK_N2 /
DDR_CK_N2
®
Intel IXP43X Product Line of Network Processors
HDG
80
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Table 33.
Signal Package Lengths (Sheet 2 of 3)
Group
Signal Name
Length (mil)
Signal Name
Length (mil)
D_CB0 / DDR_CB0
D_CB1 / DDR_CB1
D_CB2 / DDR_CB2
D_CB3 / DDR_CB3
402.94
393.93
377.69
378.47
D_CB4 / DDR_CB4
D_CB5 / DDR_CB5
D_CB6 / DDR_CB6
D_CB7 / DDR_CB7
385.50
419.24
398.22
435.03
D_DQ16 /
D_DQ0 / DDR_DQ0
D_DQ1 / DDR_DQ1
D_DQ2 / DDR_DQ2
D_DQ3 / DDR_DQ3
D_DQ4 / DDR_DQ4
D_DQ5 / DDR_DQ5
D_DQ6 / DDR_DQ6
D_DQ7 / DDR_DQ7
D_DQ8 / DDR_DQ8
D_DQ9 / DDR_DQ9
D_DQ10/ DDR_DQ10
D_DQ11 / DDR_DQ11
D_DQ12 / DDR_DQ12
D_DQ13 / DDR_DQ13
D_DQ14 / DDR_DQ14
D_DQ15 / DDR_DQ15
447.57
449.41
394.02
366.03
449.58
470.40
413.35
384.02
368.37
399.54
374.55
398.20
396.30
408.81
371.03
388.23
468.21
371.60
410.19
536.32
569.24
545.35
633.70
604.01
608.22
479.46
555.12
472.85
475.30
421.35
419.04
480.43
489.89
430.18
431.50
517.45
463.84
653.53
DDR_DQ16
D_DQ17 /
DDR_DQ17
D_DQ18 /
DDR_DQ18
D_DQ19 /
DDR_DQ19
D_DQ20 /
DDR_DQ20
D_DQ21 /
DDR_DQ21
D_DQ22 /
DDR_DQ22
D_DQ23 /
DDR_DQ23
D_DQ24 /
DDR_DQ24
Data
D_DQ25 /
DDR_DQ25
D_DQ26 /
DDR_DQ26
D_DQ27 /
DDR_DQ27
D_DQ28 /
DDR_DQ28
D_DQ29 /
DDR_DQ29
D_DQ30 /
DDR_DQ30
D_DQ31 /
DDR_DQ31
D_DQS0 /
DDR_DQS0
D_DQS2 /
DDR_DQS2
D_DQS1 /
DDR_DQS1
D_DQS3 /
DDR_DQS3
D_DQS4 /
DDR_DQS4
D_DM0 / DDR_DM0
D_DM1 / DDR_DM1
D_DM2 / DDR_DM2
D_CKE0 / DDR_CKE0
482.30
553.44
385.61
D_DM3 / DDR_DM3
D_DM4 / DDR_DM4
D_CKE1 / DDR_CKE1
536.80
428.52
384.34
Control
D_CS_N0 /
DDR_CS_N0
D_CS_N1 /
DDR_CS_N1
385.35
421.27
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
81
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Table 33.
Signal Package Lengths (Sheet 3 of 3)
Group
Signal Name
Length (mil)
Signal Name
Length (mil)
D_MA0 / DDR_MA0
D_MA1 / DDR_MA1
D_MA2 / DDR_MA2
515.78
357.69
509.12
D_MA7 / DDR_MA7
D_MA8 / DDR_MA8
D_MA9 / DDR_MA9
438.95
394.65
429.78
D_MA10 /
D_MA3 / DDR_MA3
D_MA4 / DDR_MA4
D_MA5 / DDR_MA5
462.16
444.71
576.87
378.96
418.37
392.79
DDR_MA10
D_MA11 /
DDR_MA11
D_MA12 /
DDR_MA12
Command
D_MA13 /
D_MA6 / DDR_MA6
D_BA0 / DDR_BA0
513.40
530.35
506.35
433.55
535.27
477.26
DDR_MA13
D_BA1 / DDR_BA1
D_RAS_N /
DDR_RAS_N
D_CAS_N /
DDR_CAS_N
D_WE_N /
DDR_WE_N
513.09
7.3.3
Routing Guidelines
Clock Group
7.3.3.1
The clock signal group includes the differential clock pairs D_CK[2:0] / DDR_CK[2:0]
and D_CK_N[2:0] / DDR_CK_N[2:0].
Here are some tips on how to route the differential clock pairs:
• Ensure that DDR clocks are routed on a single internal layers, except for pin
escapes
• A ground plane must be adjacent to the layer where the signals are routed
• Minimize the number of vias used, but ensure that the same number of vias are
used in the positive and negative trace
• It is recommended that pin escape vias be located directly adjacent to the ball pads
on all clocks
• Traces must be routed for differential mode impedance of 120 Ω
• Surface layer routing should be minimized (top or bottom layers)
• It is recommended to perform pre- and post-layout simulation
A series resistance value in the 25- to 50-Ω range should be used as it adds minimal
propagation delay to the signal without adversely varying from the CLK plus DQ
propagation delay average. The appropriate value for termination resistance should be
Table 34 provides routing guidelines for signals within this group.
®
Intel IXP43X Product Line of Network Processors
HDG
82
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Figure 32.
DDRII Clock Simulation Results: CK Signals
Table 34.
Clock Signal Group Routing Guidelines
Parameter
Definition
Signal Group Members
Topology
D_CK[2:0] and D_CK_N[2:0]
Differential Pair Point to Point (1 Driver, 4 Receivers)
o
50 Ω
Series Resistor
33 Ω
1
Nominal Trace Width
Internal (Strip Line) 3.5 mils, External (Micro Strip) 5 mils
2
Nominal Pair Spacing (edge to edge)
Minimum Pair to Pair Spacing
Internal (Strip Line) 10.5 mils, External (Micro Strip) 10 mils
Any layer 20mils
Minimum Spacing to Other DDR Signals
Minimum Spacing to non-DDR Signals
Maximum Via Count
20.0 mils
25.0 mils
5 per trace
Total Trace Length
500 mils to 1000 mils
DDR_CK to DDR_CK_N Length Matching
Notes:
Match total length to +/- 10 mils between clocks
1.
Nominal trace width is determined by board physical characteristics and stack-up. This value should
be verified with the PWB manufacturer to achieve the desired Zo.
2.
Nominal pair to pair spacing is determined by board physical characteristics and stack-up. This value
should be verified with the PWB manufacturer to achieve the desired Zdiff.
7.3.3.2
Data and Control Groups
The data and control signal group includes D_CB[7:0]/DDR_CB[7:0], D_DQ[31:0] /
DDR_DQ[31:0], D_DQS[4:0]/DDR_DQS[4:0], D_DM[4:0]/DDR_DM[4:0]., D_CS[1:0]/
DDR_CS[1:0] and D_CKE[1:0]/DDR_CKE[1:0]. The groups should be routed on
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
83
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
internal layers, except for pin escapes. It is recommended that pin escape vias be
located directly adjacent to the ball pads on all signals. Surface layer routing should be
minimized. The following table provides routing guidelines for signals within these
groups.
Figure 33.
DDRII Data and Control Simulation Results: DQ and DQS signals
DQ
22 ohm
DQS
Table 35.
DDRII Data and Control Signal Group Routing Guidelines
Parameter
Definition
D_CB[7:0]/DDR_CB[7:0], D_DQ[31:0] / DDR_DQ[31:0],
D_DQS[4:0]/DDR_DQS[4:0], D_DM[4:0]/DDR_DM[4:0].,
D_CS[1:0]/DDR_CS[1:0] and D_CKE[1:0]/DDR_CKE[1:0]
Signal Group Members
Topology
Differential Pair Point to Point (1 Driver, 2 Receivers)
Single Ended Trace Impedance (Z )
o
50 Ω
Series Resistor
22 Ω
1
Nominal Trace Width
Internal (Strip Line) 3.5 mils, External (Micro Strip) 5 mils
Internal (Strip Line) 10.5 mils, External (Micro Strip) 10 mils
Any layer 20mils
2
Nominal Pair Spacing (edge to edge)
Minimum Pair to Pair Spacing
Notes:
1.
Nominal trace width is determined by board physical characteristics and stack-up. This value should
be verified with the PWB manufacturer to achieve the desired Zo.
2.
Nominal pair to pair spacing is determined by board physical characteristics and stack-up. This value
should be verified with the PWB manufacturer to achieve the desired Zdiff.
®
Intel IXP43X Product Line of Network Processors
HDG
84
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Hardware Design Guidelines—Intel IXP43X Product Line of Network Processors
Table 35.
DDRII Data and Control Signal Group Routing Guidelines
Parameter
Definition
Minimum Spacing to Other DDR Signals
Minimum Spacing to non-DDR Signals
Maximum Via Count
20.0 mils
25.0 mils
5 per trace
Total Trace Length
1000 mils to 2000 mils
Notes:
1.
Nominal trace width is determined by board physical characteristics and stack-up. This value should
be verified with the PWB manufacturer to achieve the desired Zo.
Nominal pair to pair spacing is determined by board physical characteristics and stack-up. This value
should be verified with the PWB manufacturer to achieve the desired Zdiff.
2.
7.3.3.3
Command Groups
The command signal groups include all signals D_MA[13:0]/DDR_MA[13:0],
D_BA[1:0]/DDR_BA[1:0], D_RAS/DDR_RAS, D_CAS/DDR_CAS and D_WE/DDR_WE.
The groups should be routed on internal layers, except for pin escapes. It is
recommended that pin escape vias be located directly adjacent to the ball pads on all
signals. Surface layer routing should be minimized. The following table provides routing
guidelines for signals within these groups.
Figure 34.
DDRII Command Simulation Results: ADDRESS signals
20ohm
Table 36.
DDRII Command Signal Group Routing Guidelines
Parameter
Signal Group Members
Definition
D_MA[13:0]/DDR_MA[13:0], D_BA[1:0]/DDR_BA[1:0], D_RAS/DDR_RAS,
D_CAS/DDR_CAS and D_WE/DDR_WE.
Topology
Point to Point (1 Driver, 10Receivers)
Single Ended Trace Impedance (Z )
o
50 Ω
Notes:
1.
Nominal trace width is determined by board physical characteristics and stack-up. This value should
be verified with the PWB manufacturer to achieve the desired Zo.
Nominal pair to pair spacing is determined by board physical characteristics and stack-up. This value
should be verified with the PWB manufacturer to achieve the desired Zdiff.
2.
®
Intel IXP43X Product Line of Network Processors
April 2007
HDG
85
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Intel IXP43X Product Line of Network Processors—Hardware Design Guidelines
Table 36.
DDRII Command Signal Group Routing Guidelines
Parameter
Definition
Series Resistor
20 Ω
1
Nominal Trace Width
Internal (Strip Line) 3.5 mils, External (Micro Strip) 5 mils
2
Nominal Pair Spacing (edge to edge)
Minimum Pair to Pair Spacing
Internal (Strip Line) 10.5 mils, External (Micro Strip) 10 mils
Any layer 20mils
20.0 mils
Minimum Spacing to Other DDR Signals
Minimum Spacing to non-DDR Signals
Maximum Via Count
25.0 mils
5 per trace
Total Trace Length
1500 mils to 2500 mils
Notes:
1.
Nominal trace width is determined by board physical characteristics and stack-up. This value should
be verified with the PWB manufacturer to achieve the desired Zo.
2.
Nominal pair to pair spacing is determined by board physical characteristics and stack-up. This value
should be verified with the PWB manufacturer to achieve the desired Zdiff.
§ §
®
Intel IXP43X Product Line of Network Processors
HDG
86
April 2007
Document Number: 316844; Revision: 001US
Download from Www.Somanuals.com. All Manuals Search And Download.
|