|
IB935
(IB935, IB935RF)
Socket LGA775 Pentium® 4
Intel® Q35 Chipset
PICMG 1.3 SHB Express CPU Card
USER’S MANUAL
Version 1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
IB935 User’s Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
The IB935 CPU Card
iv
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Introduction
Product Description
The IB935 PICMG1.3 SHB board incorporates the Intel® Q35 Express Chipset,
consisting of the Intel® Q35 Graphic Memory Controller Hub (GMCH) and
Intel® I/O Controller Hub 9 (ICH9), is an optimized integrated graphics solution
with a 800/1066/1333 MHz front-side bus.
The integrated graphics engine, based on Intel® Graphics Media Accelerator
3100 (Intel® GMA 3100) architecture, supports Dual Independent Display and
delivers richer visual color and picture clarity without the need for additional
discrete graphics cards, and the integrated audio support enables premium digital
sound and delivers advanced features such as multiple audio.
sockets with up to 12.8 GB/s of bandwidth and 4 GB memory addressability for
faster system responsiveness and support of 64-bit computing.
The main features of the SBC are:
ƒ
Supports Intel Core 2 Duo, Core 2 Quad, and Celeron 400 (Conroe-L)
sequence processor
ƒ
ƒ
ƒ
ƒ
Two DDR2 667/800 SDRAM DIMM, Max. 4GB
Onboard Gigabit Ethernet
Intel® Q35 Express VGA for CRT
4x USB 2.0, 2x COM, Watchdog timer, Digital I/O
ƒ
ƒ
5.1 Ch. Audio
Optional backplane with 2x PCI-E(x4), 1x PCI-E (x16), 8x PCI slots,
2x ISA slots, 4x USB connectors
Dimensions of the board are 338mm x 126mm.
IB935 User’s Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Checklist
Your IB935 Pentium® 4 CPU card package should include the items
listed below:
•
•
•
•
The IB935 CPU card
This User’s manual
1 Floppy cable
1 IDE cable
• 1 USB cable with bracket (USB2K-4)
• 1 Y-Cable supporting a PS/2 Keyboard and a PS/2 Mouse
•
1 SATA cable
• 2 Serial Port Ribbon Cable and 1 Parallel Port Attached to a
Mounting Bracket
• 1 Audio cable with bracket (Audio-18K)
•
•
Optional backplane (IP314)
1 CD containing the following:
•
•
Chipset Drivers
Flash Memory Utility
Reminder:
SATA:
When using the legacy operating system, only one controller is
available and the ports supported are SATA port 0, 1 (CN1, CN2).
It is suggested that the operating system is installed using these
SATA ports.
2
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Specifications
IB935
Product Name
PICMG 1.3 SHB Express full size CPU card
Form Factor
CPU Support
Socket LGA775, Supports the Intel Core 2 Duo and Intel
Core2 Quad processors, and Intel Celeron 400 (Conroe-L)
Sequence processor.
CPU Voltage
System Speed
0.5V~1.6V (VRD 11.0)
Up to 3.8GHz+
CPU FSB
800MHz/1066MHz/1333MHz
Green /APM
CPU Socket
Chipset
APM1.2
LGA 775
Intel® Bearlake Chipset
Q35 + ICH9 for IB935
Q35 + ICH9R for IB935RF
Award BIOS; supports ACPI
Q35 built-in, supports CRT
Intel 82566DM PCI Express Gigabit PHY
Intel 82574L PCI Express Gigabit controller (IB935RF)
BIOS
VGA
LAN1
LAN2
Memory type
Support Dual Channel
DDR2 DIMM Module x 2, 667/800MHz
(Without ECC function), Max. 4GB
W83627EHG: IrDA x1, Parallel x1, COM1 (RS232), COM2
(RS232/422/485), FDCx1, Hardware monitoring
LPC I/O
RTC/CMOS
Battery
Keyboard/Mouse
IDE
Built in ICH9/ICH9R
Lithium battery
Supports PS/2 Keyboard/Mouse connector
ITE IT8211 PCI to PATA controller for one PATA channel
support
Intel ICH9 built-in SATA II controller (3.0Gb/sec) w/ 4 ports
SATA II
DB15 x1 for VGA
PS/2 Connector x1 for keyboard/mouse
RJ-45 x2 for Gigabit LAN
Edge Connector
40 pins box-header x1 for IDE1
34 pins box-header x1 for Floppy
26 pins box-header x1 for LPT
10 pins box-header x2 for COM1/2
8 (4x2) pins header x 2 for USB1~4
5 pins header x 1 for IrDA(cut pin2)
12 pins header x1 for audio Line-Out, Line-In
& Microphone
Onboard
Header/Connector
4 pins header x1 for built-in speaker
SATA connector x4 for 4 SATA ports
Yes (256 segments, 0, 1, 2… 255 sec/min)
Watchdog Timer
Digital I/O
4 In / 4 Out
+5V, +3.3V, +12V, 5VSB (2A)
System Voltage
Modem Wakeup, LAN Wakeup
338mm x 126mm
Other
Board Size
PCI w/ 4x PCI master (Supports 4 PCI Slots)
4x (x1 PCIe slots)
1x (x16 PCIe slot)
Golden Finger I/F
(Also Backplane Spec.)
4x USB2.0 ports
IB935 User’s Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Installing the CPU
The IB935 board supports an LGA 775 processor socket for Intel Core 2
Duo and Intel Core2 Quad processors, and Intel Celeron 400(Conroe-L)
Sequence processor.
The LGA 775 processor socket comes with a lever to secure the
processor. Refer to the pictures below, from left to right, on how to place
the processor into the CPU socket. Please note that the cover of the
LGA775 socket must always be installed during transport to avoid
damage to the socket.
6
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Installing the Memory
The IB935 board supports two DDR2 memory sockets for a maximum
total memory of 4GB in DDR2 memory type. It supports DDR2
667/800.
Basically, the system memory interface has the following features:
Supports two 64-bit wide DDR data channels
Available bandwidth up to 6.4GB/s (DDR2 800) for single-channel
mode and 12.8GB/s (DDR2 800) in dual-channel mode.
Supports 256Mb, 512Mb, 1Gb DDR2 technologies.
Supports only x8, x16, DDR2 devices with four banks
Supports only unbuffered DIMMs
Supports opportunistic refresh
Up to 32 simultaneously open pages (four per row, four rows
maximum)
Installing and Removing Memory Modules
To install the DDR2 modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR2 module so that the key of the DDR2 module align
with those on the memory slot.
2. Gently push the DDR2 module in an upright position until the clips of
the slot close to hold the DDR2 module in place when the DDR
module touches the bottom of the slot.
3. To remove the DDR2 module, press the clips with both hands.
DDR2 Module
Lock
Lock
Lock
Lock
IB935 User’s Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Setting the Jumpers
Jumpers are used on IB935 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on IB935 and their respective functions.
8
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
JP1, JP2, JP3: RS232/422/485 (COM2) Selection
COM1 is fixed for RS-232 use only.
COM2 is selectable for RS232, RS-422 and RS-485.
The following table describes the jumper settings for COM2 selection.
COM2
Function
RS-232
RS-422
RS-485
JP1:
1-2
JP1:
3-4
JP1:
5-6
Jumper
Setting
JP2:
JP2:
JP2:
(pin closed) 3-5 & 4-6
1-3 & 2-4
1-3 & 2-4
JP3:
JP3:
JP3:
3-5 & 4-6
1-3 & 2-4
1-3 & 2-4
JP4: Configure and Recovery (Factory use only)
JP9
Setting
Function
Pin 1-2
Short/Closed
Normal (default)
Pin 2-3
Short/Closed
Configure
Recovery
Open
JP5: Power ON Setting
JP17
Setting
Function
Pin 1-2
Short/Closed
Power on by system
button
Pin 2-3
Short/Closed
Power on by power
supply AC on
10
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
JP7: ICH9 PCI-E port 1-4 Configuration Settings
JP7 Setting
Function
Pin 1-2 & 3-4
Short
ICH9 PCI-E port 1-4 setting as 1x PCI-E x4
Pin 1/2/3/4
Open
ICH9 PCI-E port 1-4 setting as 4x PCI-E x1
JP11: Clear CMOS Contents
Use JP11 to clear the CMOS contents. Note that the ATX-power
connector should be disconnected from the board before clearing
CMOS.
JP11
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
IB935 User’s Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Connectors on IB935
The connectors on IB935 allow you to connect external devices such as
keyboard, mouse, hard disk drives, printers… etc. The following table
lists the connectors on IB935 and their respective functions.
12
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Connector Locations on IB935
ATX1: ATX 12V Power Connector
DIMM1: Channel A DDR2 Socket
DIMM2: Channel B DDR2 Socket
CPU_FAN1: CPU Fan Power
Connector
SYS_FAN1, SYS_FAN2: System
Fan Power
CN1, CN2, CN3, CN4: SATA
HDD Connector
IDE1: Primary IDE Connectors
FDC1: Floppy Drive Connector
VGA1: VGA CRT Connector
J1: External Audio Connector
J2: Parallel Port Connector
J3: Digital I/O Connector
(4 in, 4 out)
J4: IrDA Connector
J5: CD-In Audio Connector
J6: COM2 Serial Port
J7: COM1 Serial Ports Connector
J8: System Function Connector
J9: PS/2 Keyboard and Mouse
Connector
J10, J11: External PS/2 MS/KB
Connector
J12: Wake On LAN Connector
J13: USB Connector
J14: USB Connector
J15, J17: Gigabit LAN RJ45
Connector
J16: SPI Debug Tools Port
(Factory use only)
IB935 User’s Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
ATX1: ATX 12V Power Connector
Pin #
Signal Name
1
2
3
4
Ground
Ground
+12V
+12V
DIMM1: Channel A DDR2 Socket
DIMM1is the first-channel DDR2 sockets.
DIMM2: Channel B DDR2 Socket
DIMM2 is the second-channel DDR2 sockets.
CPU_FAN1: CPU Fan Power Connector
Pin #
Signal Name
Ground
+12V
Rotation detection
1
2
3
4
Control
SYS_FAN1, SYS_FAN2: SYSTEM Fan Power Connector
Pin #
Signal Name
Ground
+12V
Rotation detection
1
2
3
CN1, CN2, CN3, CN4: SATA HDD Connector
Pin #
Signal Name
Ground
TX+
1
2
3
4
5
6
7
TX-
Ground
RX-
RX+
Ground
14
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
IDE1: Primary IDE Connector
Signal Name
Pin #
Pin #
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
1
2
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Protect pin
Ground
3
4
5
6
8
7
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
DRQ0
Host IOW
Host IOR
IOCHRDY
DACK0
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
IRQ14
Address 1
Address 0
Chip select 0
Activity
IDE1
FDC1: Floppy Drive Connector
Signal Name Pin # Pin #
Signal Name
RM/LC
No connect
No connect
Index
Motor enable 0
Drive select 1
Drive select 0
Motor enable 1
Direction
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
1
3
5
7
2
4
6
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
11
13
15
17
19
21
23
25
27
29
31
33
Step
Write data
Write gate
Track 00
Write protect
Read data
FDD1
Side 1 select
Diskette change
IB935 User’s Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
VGA1: VGA CRT Connector
Signal Name Pin # Pin # Signal Name
Red
Blue
1
3
2
4
Green
N.C.
GND
5
6
GND
GND
7
8
GND
VCC
N.C.
HSYNC
DDCCLK
9
10
12
14
GND
DDCDATA
VSYNC
11
13
15
J1: External Audio Connector
J1 is a 12-pin header that is used to connect to the optional audio cable
that integrates jacks for Line In, Line Out and Mic.
Signal Name
Pin #
Pin #
Signal Name
LINEOUT R
Ground
1
3
2
4
LINEOUT L
Ground
LINEIN R
Ground
5
6
LINEIN L
Ground
7
8
10
12
Mic-In
Ground
9
VREF-Mic
Protect pin
11
J2: Parallel Port Connector
Signal Name
Pin # Pin # Signal Name
Line printer strobe
PD0, parallel data 0
PD1, parallel data 1
PD2, parallel data 2
PD3, parallel data 3
PD4, parallel data 4
PD5, parallel data 5
PD6, parallel data 6
PD7, parallel data 7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
N/A
AutoFeed
Error
Initialize
Select
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
N/A
ACK, acknowledge
Busy
J2
Paper empty
Select
16
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
J3: Digital I/O Connector (4 in, 4 out)
This 10-pin digital I/O connector supports TTL levels and is used to
control external devices requiring ON/OFF circuitry.
Signal Name Pin # Pin # Signal Name
Ground
Out3
Out2
IN3
1
3
5
7
9
2
4
6
8
10
+5V
Out1
Out0
IN1
IN2
IN0
J4: IrDA Connector
Pin #
Signal Name
+5V
No connect
Ir RX
1
2
3
4
5
Ground
Ir TX
J5: CD-In Audio Connector
Pin # Signal Name
1
2
3
4
CD Audio R
Ground
Ground
CD Audio L
IB935 User’s Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
J6: COM2 Serial Port
COM2 is jumper selectable for RS-232, RS-422 and RS-485.
Please refer to JP1, JP2, JP3: RS232/422/485 (COM2) Selection
Pin
#
Signal Name
RS-232
DCD
RX
R2-422
TX-
TX+
RS-485
DATA-
DATA+
NC
1
2
3
TX
RX+
4
5
6
7
8
9
10
DTR
Ground
DSR
RTS
CTS
RI
RX-
NC
Ground
NC
NC
NC
Ground
RTS-
RTS+
CTS+
CTS-
NC
NC
NC
NC
J7: COM1 Serial Ports Connector
J7 is a 10-pin header support RS232 COM ports.
Signal
Name
DCD
RX
Pin
Pin
Signal
Name
DSR
RTS
CTS
RI
1
2
3
4
5
6
7
8
9
10
TX
DTR
GND
NC
J8: System Function Connector
J8 provides connectors for system indicators that provide light indication
of the computer activities and switches to change the computer status.
18
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Speaker: Pins 1 - 4
This connector provides an interface to a speaker for audio
tone generation. An 8-ohm speaker is recommended.
Pin #
Signal Name
Speaker out
No connect
Ground
1
2
3
4
+5V
Power LED: Pins 11 - 13
The power LED indicates the status of the main power
switch.
Pin #
11
12
Signal Name
Power LED
No connect
Ground
13
ATX Power ON Switch: Pins 7 and 17
This 2-pin connector is an “ATX Power Supply On/Off
Switch” on the system that connects to the power switch on
the case. When pressed, the power switch will force the
system to power on. When pressed again, it will force the
system to power off.
Reset Switch: Pins 9 and 19
The reset switch allows the user to reset the system without
turning the main power switch off and then on again.
Orientation is not required when making a connection to
this header.
IB935 User’s Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
Hard Disk Drive LED Connector: Pins 10 and 20
This connector connects to the hard drive activity LED on
control panel. This LED will flash when the HDD is being
accessed.
Pin #
10
20
Signal Name
HDD Active
5V
J9: PS/2 Keyboard and Mouse Connector
J9 uses a Y-cable with dual D-connectors for a PS/2 keyboard and a PS/2
mouse.
Pin #
Signal Name
Keyboard data
Mouse data
Ground
1
2
3
4
5
6
Vcc
Keyboard Clock
Mouse Clock
J9
J10, J11: External PS/2 Mouse and Keyboard Connector
Pin #
J10
KB clock
KB data
N.C.
Ground
Vcc
J11
Mouse data
N.C.
Ground
Vcc
1
2
3
4
5
Mouse clock
J12: Wake On LAN Connector
J12 is a 3-pin header for the Wake On LAN function on the
motherboard. The following table shows the pin out assignments of this
connector. Wake On LAN will function properly only with an ATX
power supply with 5VSB that has 1A.
Pin #
Signal Name
+5VSB
Ground
LAN Wakeup
1
2
3
20
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
J13: USB Connector
The following table shows the pin outs of the USB pin header.
Signal Name Pin Pin Signal Name
Vcc
1
2
3
4
5
6
7
8
Ground
USB1+
USB1-
Vcc
USB0-
USB0+
Ground
J13
J14: USB Connector
The following table shows the pin outs of the USB pin header.
Signal Name Pin Pin Signal Name
Vcc
1
2
3
4
5
6
7
8
Ground
USB3+
USB3-
Vcc
USB2-
USB2+
Ground
J14
J15, J17: Gigabit LAN RJ45 Connector
J15, J17 are Gigabit LAN RJ45 connectors.
J16: SPI Debug Tools Port (Factory use only)
IB935 User’s Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONS
This page is intentionally left blank.
22
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
BIOS Setup
This chapter describes the different settings available in the Award
BIOS that comes with the board. The topics covered in this chapter are
as follows:
BIOS Introduction ............................................................................... 24
Save & Exit Setup ............................................................................... 44
IB935 User’s Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your
computer system’s ROM supports Intel processors. The BIOS provides
critical low-level support for a standard device such as disk drives, serial
ports and parallel ports. It also adds virus and password protection as
well as special support for detailed fine-tuning of the chipset controlling
the entire system.
BIOS Setup
The Award BIOS provides a Setup utility program for specifying the
system configurations and settings. The BIOS ROM of the system stores
the Setup utility. When you turn on the computer, the Award BIOS is
immediately activated. Pressing the <Del> key immediately allows you
to enter the Setup utility. If you are a little bit late pressing the <Del>
key, POST (Power on Self Test) will continue with its test routines, thus
preventing you from invoking the Setup. If you still wish to enter Setup,
restart the system by pressing the ”Reset” button or simultaneously
pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by
turning the system off and back on again. The following message will
appear on the screen:
Press <DEL> to Enter Setup
In general, you press the arrow keys to highlight items, <Enter> to
select, the <PgUp> and <PgDn> keys to change entries, <F1> for help
and <Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup
functions and exit choices.
24
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Frequency/Voltage Control
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
ESC : Quit
Ç È Æ Å : Select Item
F10 : Save & Exit Setup
Time, Date, Hard Disk Type…
The section below the setup items of the Main Menu displays the control
keys for this menu. At the bottom of the Main Menu just below the
control keys section, there is another section, which displays information
on the currently highlighted item in the list.
Note:
If the system cannot boot after making and saving system
changes with Setup, the Award BIOS supports an override to
the CMOS settings that resets your system to its default.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both Award and your system
manufacturer to provide the absolute maximum performance
and reliability. Changing the defaults could cause the system
to become unstable and crash in some cases.
IB935 User’s Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Standard CMOS Setup
“Standard CMOS Setup” choice allows you to record some basic
hardware configurations in your computer system and set the system
clock and error handling. If the motherboard is already installed in a
working system, you will not need to select this option. You will need to
run the Standard CMOS option, however, if you change your system
hardware configurations, the onboard battery fails, or the configuration
stored in the CMOS memory was lost or damaged.
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Wed, Oct 3, 2007
16 : 11 : 00
Item Help
Menu Level >
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
None
None
None
None
Change the day, month,
Year and century
Drive A
Drive B
1.44M, 3.5 in.
None
Video
EGA/VGA
Halt On
All , But Keyboard
Base Memory
640K
Extended Memory
Total Memory
2086912K
2087936K
At the bottom of the menu are the control keys for use on this menu. If
you need any help in each item field, you can press the <F1> key. It will
display the relevant information to help you. The memory display at the
lower right-hand side of the menu is read-only. It will adjust
automatically according to the memory changed. The following
describes each item of this menu.
Date
The date format is:
Day :
Sun to Sat
1 to 12
1 to 31
Month :
Date :
Year :
1999 to 2099
To set the date, highlight the “Date” field and use the PageUp/
PageDown or +/- keys to set the current time.
26
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Time
The time format is: Hour : 00 to 23
Minute : 00 to 59
Second : 00 to 59
To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn>
or +/- keys to set the current time.
IDE Channel Master/Slave
The onboard Serial ATA connectors provide Primary and Secondary
channels for connecting up to four Serial ATA hard disks . Each channel
can support up to two hard disks; the first is the “Master” and the second
is the “Slave”.
Press <Enter> to configure the hard disk. The selections include Auto,
Manual, and None. Select ‘Manual’ to define the drive information
manually. You will be asked to enter the following items.
Capacity :
Cylinder :
Head :
Capacity/size of the hard disk drive
Number of cylinders
Number of read/write heads
Write precompensation
Precomp :
Landing Zone : Landing zone
Sector :
Number of sectors
The Access Mode selections are as follows:
CHS
LBA
(HD < 528MB)
(HD > 528MB and supports Logical Block Addressing)
Large (for MS-DOS only)
Auto
Drive A / Drive B
These fields identify the types of floppy disk drive A or drive B that has
been installed in the computer. The available specifications are:
360KB 1.2MB 720KB 1.44MB 2.88MB
5.25 in. 5.25 in. 3.5 in.
3.5 in.
3.5 in.
IB935 User’s Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Video
This field selects the type of video display card installed in your system.
You can choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA
or PGA monitor adapters. (default)
Power up in 40 column mode.
Power up in 80 column mode.
For Hercules or MDA adapters.
CGA 40
CGA 80
MONO
Halt On
This field determines whether or not the system will halt if an error is
detected during power up.
No errors
The system boot will not be halted for any error
that may be detected.
All errors
Whenever the BIOS detects a non-fatal error,
the system will stop and you will be prompted.
The system boot will not be halted for a
keyboard error; it will stop for all other errors
The system boot will not be halted for a disk
error; it will stop for all other errors.
All, But Keyboard
All, But Diskette
All, But Disk/Key
The system boot will not be halted for a key-
board or disk error; it will stop for all others.
28
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Advanced BIOS Features
This section allows you to configure and improve your system and
allows you to set up some system features according to your preference.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
CPU Feature
Press Enter
Press Enter
Disabled
Enabled
Enabled
CDROM
Legacy LAN
Hard Disk
Enabled
Disabled
Disabled
On
ITEM HELP
Menu Level >
Hark Disk Boot Priority
Virus Warming
CPU L3 Cache
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Gate A20 Option
Fast
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
Disabled
6
250
Setup
APIC Mode
Enabled
1.4
Non-OS2
No
MPS Version Control for OS
OS Select For DRAM>64MB
Report No FDD For WIN 95
Small Logo (EPA) Show
Disabled
CPU Feature
Press Enter to configure the settings relevant to CPU Feature.
Hard Disk Boot Priority
Press Enter to configure the settings.
Virus Warming
If this option is enabled, an alarm message will be displayed when trying
to write on the boot sector or on the partition table on the disk, which is
typical of the virus.
CPU L3 Cache
Cache memory is additional memory much faster than conventional
DRAM (system memory). CPUs from 486-type on up contain internal
cache memory, and most, but not all, modern PCs have additional
(external) cache memory. When the CPU requests data, the system
transfers the requested data from the main DRAM into cache memory,
for even faster access by the CPU. By default, these items are enabled.
Quick Power On Self Test
When enabled, this field speeds up the Power On Self Test (POST) after
the system is turned on. If it is set to Enabled, BIOS will skip some
items.
IB935 User’s Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
First/Second/Third Boot Device
These fields determine the drive that the system searches first for an
operating system.
Boot Other Device
These fields allow the system to search for an OS from other devices
other than the ones selected in the First/Second/Third Boot Device.
Swap Floppy Drive
This item allows you to determine whether or not to enable Swap Floppy
Drive. When enabled, the BIOS swaps floppy drive assignments so that
Drive A becomes Drive B, and Drive B becomes Drive A. By default,
this field is set to Disabled.
Boot Up Floppy Seek
This feature controls whether the BIOS checks for a floppy drive while
booting up. If it cannot detect one (either due to improper configuration
or its absence), it will flash an error message.
Boot Up NumLock Status
This allows you to activate the NumLock function after you power up
the system.
Gate A20 Option
This field allows you to select how Gate A20 is worked. Gate A20 is a
device used to address memory above 1 MB.
Typematic Rate Setting
When disabled, continually holding down a key on your keyboard will
generate only one instance. When enabled, you can set the two typematic
controls listed next. By default, this field is set to Disabled.
Typematic Rate (Chars/Sec)
When the typematic rate is enabled, the system registers repeated
keystrokes speeds. Settings are from 6 to 30 characters per second.
Typematic Delay (Msec)
When the typematic rate is enabled, this item allows you to set the time
interval for displaying the first and second characters. By default, this
item is set to 250msec.
30
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Security Option
This field allows you to limit access to the System and Setup. The default
value is Setup. When you select System, the system prompts for the User
Password every time you boot up. When you select Setup, the system
always boots up and prompts for the Supervisor Password only when the
Setup utility is called up.
APIC Mode
APIC stands for Advanced Programmable Interrupt Controller. The
default setting is Enabled.
MPS Version Control for OS
This option is specifies the MPS (Multiprocessor Specification) version
for your operating system. MPS version 1.4 added extended
configuration tables to improve support for multiple PCI bus
configurations and improve future expandability. The default setting is
1.4.
OS Select for DRAM > 64MB
This option allows the system to access greater than 64MB of DRAM
memory when used with OS/2 that depends on certain BIOS calls to
access memory. The default setting is Non-OS/2.
Report No FDD For WIN 95
If you are using Windows 95/98 without a floppy disk drive, select
Enabled to release IRQ6. This is required to pass Windows 95/98's SCT
test. You should also disable the Onboard FDC Controller in the
Integrated Peripherals screen when there's no floppy drive in the system.
If you set this feature to Disabled, the BIOS will not report the missing
floppy drive to Win95/98.
Small Logo (EPA) Show
The EPA logo appears at the right side of the monitor screen when the
system is boot up. The default setting is Disabled.
IB935 User’s Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Advanced Chipset Features
This Setup menu controls the configuration of the chipset.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Timing Selectable
CAS Latency Time
By SPD
Auto
ITEM HELP
Menu Level >
DRAM RAS# to CAS# Delay
DRAM RAS# Precharge
Precharge dealy (tRAS)
System Memory Frequency
System BIOS Cacheable
Memory Hole at 15M-16M
PCI Express Root Port Func
Auto
Auto
Auto
By SPD
Enabled
Disabled
Press Enter
** VGA Setting **
PEG/On Chip VGA Control
On-Chip Frame Buffer Size
DVMT Mode
Auto
8MB
DVMT
DVMT/FIXED memory Size
SDVO Device Setting
SDVO LVDS Protocol
SDVO Panel Number
Boot Display
128MB
None
1 Ch 18bit
852 x 480
Auto
Panel Scaling
Auto
Panel Number
Onboard Lan Boot ROM
Onboard IT8211F IDE ROM
1024 x 768 18bit SC
Enabled
Enabled
DRAM Timing Selectable
This option refers to the method by which the DRAM timing is selected.
The default is By SPD.
CAS Latency Time
You can select CAS latency time in HCLKs of 3/3 or 4/4. The system
board designer should set the values in this field, depending on the
DRAM installed. Do not change the values in this field unless you
change specifications of the installed DRAM or the installed CPU. The
choices are 3, 4 and 5.
DRAM RAS# to CAS# Delay
This option allows you to insert a delay between the RAS (Row Address
Strobe) and CAS (Column Address Strobe) signals. This delay occurs
when the SDRAM is written to, read from or refreshed. Reducing the
delay improves the performance of the SDRAM.
DRAM RAS# Precharge
This option sets the number of cycles required for the RAS to
accumulate its charge before the SDRAM refreshes.
32
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Precharge delay (tRAS)
The default setting for the Active to Precharge Delay is Auto.
System Memory Frequency
This field sets the frequency of the DRAM memory installed. The
default setting is Auto. The other settings are DDR667 and DDR800.
System BIOS Cacheable
The setting of Enabled allows caching of the system BIOS ROM at
F000h-FFFFFh, resulting in better system performance. However, if
any program writes to this memory area, a system error may result.
Memory Hole At 15M-16M
In order to improve performance, certain space in memory can be
reserved for ISA cards. This memory must be mapped into the memory
space below 16 MB. The choices are Enabled and Disabled.
PCI Express Root Port Func
Press Enter to configure this field.
VGA Setting
The fields under the On-Chip VGA Setting and their default settings are:
PEG/On Chip VGA Control: Auto
On-Chip Frame Buffer Size: 8MB
DVMT Mode: DVMT
DVMT/Fixed Memory Size: 128MB
SDVO Device Setting: None
To use the single DVI setting, install the IBP192-R DVI module; to
use the dual DVI setting, install the IBP192D-R DVI module; and
to use the LVDS+TV or LVDS or TV-out setting, install the IBP190
module.
SDVO LVDS Protocol: 1Ch 18bit
SDVO Panel Number: 852 x 480
Boot Display: Auto
Panel Scaling: Auto
Panel Number: 1024 x 768 18bit SC
Onboard Lan Boot ROM: Enabled
Onboard IT8211F IDE ROM: Enabled
IB935 User’s Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Integrated Peripherals
This section sets configurations for your hard disk and other integrated
peripherals. The first screen shows three main items for user to select.
Once an item selected, a submenu appears. Details follow.
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
Press Enter
Press Enter
Press Enter
ITEM HELP
Menu Level >
OnChip IDE Device
SuperIO Device
USB Device Setting
Phoenix - AwardBIOS CMOS Setup Utility
OnChip IDE Device
Enabled
Enabled
ITEM HELP
IDE HDD Block Mode
IDE DMA transfer access
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
On-Chip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
SATA Mode
Auto
Auto
Auto
Auto
Enabled
Auto
Auto
Auto
Auto
Menu Level >
IDE
LEGACY Mode Support
Enabled
Phoenix - AwardBIOS CMOS Setup Utility
Onboard Device
ITEM HELP
POWER ON Function
KB Power ON Password
Hot Key power ON
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
RxD , TxD Active
BUTTON ONLY
Enter
Ctrl-F1
Enabled
Menu Level >
3F8/IRQ4
2F8/IRQ3
Normal
Hi, Lo
IR Transmission Delay
UR2 Duplex Mode
Enabled
Half
Use IR Pins
IR-Rx2Tx2
378/IRQ7
SPP
EPP1.7
3
Onboard Parallel Port
Parallel Port Mode
EPP Mode Select
ECP Mode Use DMA
PWRON After PWR-Fail
Off
34
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Phoenix - AwardBIOS CMOS Setup Utility
USB Device Setting
Enabled
ITEM HELP
USB 1.0 Controller
Enabled
Disabled
Disabled
Menu Level >
USB 2.0 Controller
USB Keyboard Function
USB Mouse Function
USB Storage Function
Enabled
*** USB Mass Storage Device Boot Setting ***
IDE HDD Block Mode
This field allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive.
IDE DMA Transfer Access
This field, by default, is enabled
OnChip Secondary PCI IDE
This field, by default, is enabled
IDE Primary/Secondary Master/Slave PIO
These fields allow your system hard disk controller to work faster.
Rather than have the BIOS issue a series of commands that transfer to or
from the disk drive, PIO (Programmed Input/Output) allows the BIOS to
communicate with the controller and CPU directly.
The system supports five modes, numbered from 0 (default) to 4, which
primarily differ in timing. When Auto is selected, the BIOS will select
the best available mode.
IDE Primary/Secondary Master/Slave UDMA
These fields allow your system to improve disk I/O throughput to
33Mb/sec with the Ultra DMA/33 feature. The options are Auto and
Disabled.
SATA Mode
The setting choices for the SATA Mode are IDE, RAID and AHCI
Mode. Select [IDE] if you want to have SATA function as IDE.
Select [AHCI] for Advanced Host Controller Interface (AHCI) feature,
with improved SATA performance with native command queuing &
native hot plug. Select [RAID] to use SATA as RAID function. RAID
function is supported on the board if it uses ICH9R, but this is optional.
IB935 User’s Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
LEGACY Mode Support
When the Serial ATA (SATA) is set with the legacy mode enabled, then
the SATA is set to the conventional IDE mode. Legacy mode is
otherwise known as compatible mode.
Power ON Function
This field is related to how the system is powered on – such as with the
use of conventional power button, keyboard or hot keys. The default is
BUTTON ONLY.
KB Power ON Password
This field allows users to set the password when keyboard power on is
the mode of the Power ON function.
Hot Key Power ON
This field sets certain keys, also known as hot keys, on the keyboard that
can be used as a ‘switch’ to power on the system.
Onboard FDC Controller
Select Enabled if your system has a floppy disk controller (FDC)
installed on the motherboard and you wish to use it. If you install an
add-in FDC or the system has no floppy drive, select Disabled in this
field. This option allows you to select the onboard FDD port.
Onboard Parallel/Serial Port
These fields allow you to select the onboard serial and parallel ports and
their addresses. The default values for these ports are:
Serial Port 1
Serial Port 2
Parallel Port
3F8/IRQ4
2F8/IRQ3
378H/IRQ7
UART Mode Select
This field determines the UART 2 mode in your computer. The default
value is Normal.
36
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Parallel Port Mode
This field allows you to determine parallel port mode function.
SPP
Standard Printer Port
EPP
Enhanced Parallel Port
ECP
ECP+EPP
Normal
Extended Capabilities Port
Combination of ECP and EPP capabilities
Normal function
PWRON After PWR-Fail
This field sets the system power status whether on or off when power
returns to the system from a power failure situation.
USB 1.0 Controller
The options for this field are Enabled and Disabled. By default, this field
is set to Enabled.
USB 2.0 Controller
The options for this field are Enabled and Disabled. By default, this field
is set to Enabled. In order to use USB 2.0, necessary OS drivers must be
installed first. Please update your system to Windows 2000 SP4 or
Windows XP SP1.
USB Keyboard Support
The options for this field are Enabled and Disabled. By default, this field
is set to Disabled.
USB Mouse Support
The options for this field are Enabled and Disabled. By default, this field
is set to Disabled.
USB Storage Function
The options for this field are Enabled and Disabled. By default, this field
is set to Disabled.
IB935 User’s Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Power Management Setup
The Power Management Setup allows you to save energy of your system
effectively.
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
Enabled
S3(STR)
User Define
DPMS
ITEM HELP
ACPI Function
ACPI Suspend Type
Power Management
Video Off Method
Video Off In Suspend
Suspend Type
Menu Level >
Yes
Stop Grant
3
Modem Use IRQ
Suspend Mode
Disabled
Disabled
Instant-Off
50%
Disabled
Disabled
Disabled
Disabled
0
HDD Power Down
Soft-Off by PWR-BTTN
CPU THRM-Throttling
Wake-Up by PCI Card
Power On by Ring
USB KB Wake-up From S3
Resume by Alarm
Date (of Month) Alarm
Time (hh:mm:ss) Alarm
0 : 0 : 0
** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port
PCI PIRQ[A-D] #
HPET Support
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
32-bit mode
HPET Mode
ACPI Function
Enable this function to support ACPI (Advance Configuration and
Power Interface).
ACPI Suspend
The default setting of the ACPI Suspend mode is S3(STR).
Power Management
This field allows you to select the type of power saving management
modes. There are four selections for Power Management.
Min. Power Saving
Max. Power Saving
User Define
Minimum power management
Maximum power management.
Each of the ranges is from 1 min. to
1hr. Except for HDD Power Down
which ranges from 1 min. to 15 min.
38
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Video Off Method
This field defines the Video Off features. There are three options.
V/H SYNC + Blank
Default setting, blank the screen and turn
off vertical and horizontal scanning.
Allows BIOS to control the video display.
Writes blanks to the video buffer.
DPMS
Blank Screen
Video Off In Suspend
When enabled, the video is off in suspend mode. The default setting is
Yes.
Suspend Type
The default setting for the Suspend Type field is Stop Grant.
Modem Use IRQ
This field sets the IRQ used by the Modem. By default, the setting is 3.
Suspend Mode
When enabled, and after the set time of system inactivity, all devices
except the CPU will be shut off.
HDD Power Down
When enabled, and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.
Soft-Off by PWR-BTTN
This field defines the power-off mode when using an ATX power
supply. The Instant Off mode allows powering off immediately upon
pressing the power button. In the Delay 4 Sec mode, the system powers
off when the power button is pressed for more than four seconds or
enters the suspend mode when pressed for less than 4 seconds.
CPU THRM-Throttling
When the system enters Doze mode, the CPU clock runs only part of the
time. You may select the percent of time that the clock runs.
Wake up by PCI Card
By default, this field is disabled.
IB935 User’s Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Power On by Ring
This field enables or disables the power on of the system through the
modem connected to the serial port or LAN.
Resume by Alarm
This field enables or disables the resumption of the system operation.
When enabled, the user is allowed to set the Date and Time.
Reload Global Timer Events
The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events that can
prevent the system from entering a power saving mode or can awaken
the system from such a mode. When an I/O device wants to gain the
attention of the operating system, it signals this by causing an IRQ to
occur. When the operating system is ready to respond to the request, it
interrupts itself and performs the service.
40
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
PNP/PCI Configurations
This option configures the PCI bus system. All PCI bus systems on the
system use INT#, thus all installed PCI cards must be set to this value.
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
No
PNP OS Installed
PCI Slot
Disabled
ITEM HELP
Init Display First
Reset Configuration Data
Menu Level >
Auto (ESCD)
Resources Controlled By
IRQ Resources
Press Enter
Press Enter
DMA Resources
Disabled
128
PCI/VGA Palette Snoop
**PCI Express relative items**
Maximum Payload Size
PNP OS Installed
Enable the PNP OS Install option if it is supported by the
operating system installed. The default value is No.
Init Display First
The default setting is PCI Card.
Reset Configuration Data
This field allows you to determine whether to reset the configuration
data or not. The default value is Disabled.
Resources Controlled by
This PnP BIOS can configure all of the boot and compatible devices
automatically with the use of a use a PnP operating system such as
Windows 95.
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors properly.
This field allows you to set whether or not MPEG ISA/VESA VGA
cards can work with PCI/VGA. When this field is enabled, a PCI/VGA
can work with an MPEG ISA/VESA VGA card. When this field is
disabled, a PCI/VGA cannot work with an MPEG ISA/VESA card.
Maximum Payload Size
The default setting of the PCI Express Maximum Payload Size is 128.
IB935 User’s Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
PC Health Status
This section shows the parameters in determining the PC Health Status.
These parameters include temperatures, fan speeds and voltages.
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
ITEM HELP
Shutdown Temperature
CPU Warning Temperature
Current System Temp.
Current CPU1 Temperature
Current CPU2 Temperature
FAN1 Speed
Disabled
Disabled
34°C/93°F
27°C/80°F
0°C/32°F
0 RPM
Menu Level >
FAN2 Speed
FAN3 Speed
Vcore(V)
VIN0
4400 RPM
0 RPM
1.02 V
1.32 V
3.32 V
4.94 V
3.32 V
3.08 V
4.96 V
VIN1
VIN3
3.3V
VBAT(V)
5VSB(V)
Smart Fan Temperature
Fan Tolerance Value
Disabled
4
Shutdown Temperature
This field allows the user to set the temperature by which the system
automatically shuts down once the threshold temperature is reached.
This function can help prevent damage to the system that is caused by
overheating.
CPU Warning Temperature
This field allows the user to set the temperature so that when the
temperature is reached, the system sounds a warning. This function can
help prevent damage to the system that is caused by overheating.
Temperatures/Fan Speeds/Voltages
These fields are the parameters of the hardware monitoring function
feature of the board. The values are read-only values as monitored by the
system and show the PC health status.
Smart Fan Temperature
This field enables or disables the smart fan feature. At a certain
temperature, the fan starts turning. Once the temperature drops to a
certain level, it stops turning again.
42
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Frequency/Voltage Control
This section shows the user how to configure the processor frequency.
Phoenix - AwardBIOS CMOS Setup Utility
Frequency/Voltage Control
8 X
Disabled
ITEM HELP
CPU Clock Ratio
Auto Detect PCI Clk
Spread Spectrum
Disabled
Menu Level >
Auto Detect PCI Clk
This field enables or disables the auto detection of the PCI clock.
Spread Spectrum
This field sets the value of the spread spectrum. The default setting is
Disabled. This field is for CE testing use only.
IB935 User’s Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS SETUP
Load Fail-Safe Defaults
This option allows you to load the troubleshooting default values
permanently stored in the BIOS ROM. These default settings are
non-optimal and disable all high-performance features.
Load Optimized Defaults
This option allows you to load the default values to your system
configuration. These default settings are optimal and enable all high
performance features.
Set Supervisor Password
These two options set the system password. Supervisor Password sets a
password that will be used to protect the system and Setup utility. User
Password sets a password that will be used exclusively on the system. To
specify a password, highlight the type you want and press <Enter>. The
Enter Password: message prompts on the screen. Type the password, up
to eight characters in length, and press <Enter>. The system confirms
your password by asking you to type it again. After setting a password,
the screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are
prompted to enter the password. A message will confirm the password to
be disabled. Once the password is disabled, the system will boot and you
can enter Setup freely.
Save & Exit Setup
This option allows you to determine whether or not to accept the
modifications. If you type “Y”, you will quit the setup utility and save all
changes into the CMOS memory. If you type “N”, you will return to
Setup utility.
Exit Without Saving
Select this option to exit the Setup utility without saving the changes you
have made in this session. Typing “Y” will quit the Setup utility without
saving the modifications. Typing “N” will return you to Setup utility.
44
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
Drivers Installation
This section describes the installation procedures for software and
drivers under the Windows 98SE, Windows ME, Windows 2000 and
Windows XP. The software and drivers are included with the
motherboard. If you find the items missing, please contact the vendor
where you made the purchase. The contents of this section include the
following:
Intel Chipset Software Intallation Utility...................................46
Intel Graphics Driver Installation ..............................................48
Realtek HD Code Audio Driver Installation..............................49
Intel PRO LAN Drivers Installation ..........................................50
IDE Controller Driver Installation……………………………..52
IMPORTANT NOTE:
1. After installing your Windows operating system(Windows
98SE/ME/2000/XP), you must install first the Intel Chipset Software
Installation Utility before proceeding with the drivers installation.
2. How to create an AHCI driver disk, when your board supports the
RAID/AHC function:
1.Put an empty disc into your floppy disk drive
2.Execute the f6flpy32.exe that is in the Driver CD you have received.
The path is 8.1D\Intel\Q35\Raid\
3.When IDE Device (HDD, CDROM, etc.) is to be used, one must use a
USB-FDD device (with the IDE device driver floppy diskette inserted)
to install the drivers when Windows is initializing. When Windows is
starting, press F6 and follow the proceeding instructions. The IDE
device drivers can be found in the driver DVD disc that is provided with
the motherboard with location in E:\SCSI\ITE8211\DISK\ (assuming E:
is the DVD ROM drive).
IB935 User’s Manual
45
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVER INSTALLATION
Intel Chipset Software Intallation Utility
The Intel Chipset Drivers should be installed first before the software
drivers to enable Plug & Play INF support for Intel chipset components.
Follow the instructions below to complete the installation under
Windows 98SE/ME/2000/XP. (Before installed Intel Chipset Software
Installation Utility,Please update your system to Windows 2000 SP4 or
Windows XP SP1A)
1. Insert the CD that comes with the board. Click Intel Chipsets and then
Intel(R) Bearlake Chipset Family Drivers.
2. Click Intel(R) Chipset Software Installation Utility.
3. When the Welcome screen appears, click Next to continue.
46
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
4. Click Yes to accept the software license agreement and proceed with
the installation process.
5. On the Readme Information screen, click Next to continue the
installation.
6. When the Setup Progress screen appears, click Next to continue.
7. The Setup process is now complete. Click Finish then restart the
computer and for changes to take effect.
IB935 User’s Manual
47
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVER INSTALLATION
Intel Graphics Driver Installation
To install the Graphics drivers, follow the steps below to proceed with
the installation.
1. Insert the DVD that comes with the board. Click Intel Chipsets and
then Intel(R) Bearlake Chipset Family Drivers.
2. Click Intel(R) Bearlake Chipset Family Graphics Driver.
3. When the Welcome screen appears, click Next to continue.
4. Click Yes to accept the software license agreement and proceed with
the installation process.
5. On Readme File Information screen, click Next to continue.
6. On Setup Progress screen, click Next to continue the installation.
7. The Setup process is now complete. Click Finish to restart the
computer and for changes to take effect.
48
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
Realtek HD Code Audio Driver Installation
Follow the steps below to install the Realtek High Definition Codec
Audio Driver.
1. Insert the DVD that comes with the board. Click Intel Chipsets and
then Intel(R) Bearlake Chipset Family Drivers.
2. Click Realtek High Definition Codec Audio Driver.
3. When the Welcome screen appears, click Next to continue.
4. The Setup process is now complete. Restart the computer when
prompted for changes to take effect.
IB935 User’s Manual
49
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVER INSTALLATION
Intel PRO LAN Drivers Installation
Follow the steps below to start installing the Intel 82566DM or Intel
82574L drivers.
1. Insert the DVD that comes with the board. Click Intel Chipsets and
then Intel(R) Bearlake Chipset Family Drivers.
2. Click Intel(R) PRO LAN Network Drivers.
3. On the next screen, click Install Drivers to start the drivers
installation.
4. When the Welcome screen appears, click Next to continue.
5. In the License Agreement screen, click I accept the terms in license
agreement and Next to accept the software license agreement and
proceed with the installation process.
6. When the Setup Options appears, click Install Drivers only and Next
to continue.
7. When the Ready to Install the Program screen appears, click Install to
continue.
8. The Setup process is now complete (InstallShield Wizard Completed).
Click Finish to restart the computer and for changes to take effect.
50
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVERS INSTALLATION
Follow the steps below to use the wake up function by Intel 82566DM or
Intel 82574L.
1. The BIOS Setup item “Wake-Up by PCI card” has to be set as
[Enabled] .
2. Go to the Device Manager under Windows and select Network
adapters. The following window will appear (Intel(R) 82566DM Gigabit
Network Connection Properties). Click Power Management and select
Wake on Magic Packet from power off states .
3. Turn off computer .
IB935 User’s Manual
51
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVER INSTALLATION
IDE Controller Drivers Installation
Follow the steps below to install IDE Controller Drivers.
1. Insert the CD that comes with the motherboard. Click ITE8211 Chip
and then IDE Controller Drivers . When the Welcome screen appears,
click Next to continue.
2. Select Type as ‘Typical’ and click Next to continue. Restart when
promoted and finish the installation process.
52
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Appendix
A. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port
addresses which also becomes the identity of the device. The following
table lists the I/O port addresses used.
Address
Device Description
DMA Controller #1
Interrupt Controller #1
Timer
Keyboard Controller
Real Time Clock, NMI
DMA Page Register
Interrupt Controller #2
DMA Controller #2
Clear Math Coprocessor Busy Signal
Reset Math Coprocessor
IDE Interface
Parallel Port #2(LPT2)
Serial Port #2(COM2)
Graphics adapter Controller
Parallel Port #1(LPT1)
Network Ports
000h - 01Fh
020h - 03Fh
040h - 05Fh
060h - 06Fh
070h - 07Fh
080h - 09Fh
0A0h - 0BFh
0C0h - 0DFh
0F0h
0F1h
1F0h - 1F7h
278 - 27F
2F8h - 2FFh
2B0 - 2DF
378h - 3FFh
360 - 36F
3B0 - 3BF
3C0 - 3CF
3D0 - 3DF
3F0h - 3F7h
3F8h - 3FFh
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy Disk Controller
Serial Port #1(COM1)
IB935 User’s Manual
53
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
B. Interrupt Request Lines (IRQ)
Peripheral devices use interrupt request lines to notify CPU for the
service required. The following table shows the IRQ used by the devices
on board.
Level
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
Function
System Timer Output
Keyboard
Interrupt Cascade
Serial Port #2
Serial Port #1
Reserved
Floppy Disk Controller
Parallel Port #1
Real Time Clock
Reserved
Reserved
Reserved
PS/2 Mouse
80287
Primary IDE
Secondary IDE
54
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
C. Watchdog Timer Configuration
The WDT is used to generate a variety of output signals after a user
programmable count. The WDT is suitable for use in the prevention of
system lock-up, such as when software becomes trapped in a deadlock.
Under these sort of circumstances, the timer will count to zero and the
selected outputs will be driven. Under normal circumstance, the user
will restart the WDT at regular intervals before the timer counts to zero.
SAMPLE CODE:
This code and information is provided "as is" without warranty of any
kind, either expressed or implied, including but not limited to the
implied warranties of merchantability and/or fitness for a particular
purpose.
;[]================================================
; Name : Enable_And_Set_Watchdog
; IN
: AL - 1sec ~ 255sec
; OUT : None
;[]================================================
Enable_And_Set_Watchdog Proc
Near
push
ax
;save time interval
call Unlock_Chip
mov cl, 2Bh
call Read_Reg
and al, NOT 10h
call Write_Reg
;set GP24 as WDTO
;switch to LD8
mov cl, 07h
mov al, 08h
call Write_Reg
IB935 User’s Manual
55
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
mov cl, 0F5h
call Read_Reg
and al, NOT 08h
call Write_Reg
;set count mode as second
;set watchdog timer
;watchdog enabled
pop ax
mov cl, 0F6h
call Write_Reg
mov al, 01h
mov cl, 30h
call Write_Reg
call Lock_Chip
ret
Enable_And_Set_Watchdog Endp
;[]===============================================
; Name : Disable_Watchdog
; IN
: None
; OUT : None
;[]===============================================
Disable_Watchdog Proc
call Unlock_Chip
Near
mov cl, 07h
mov al, 08h
call Write_Reg
;switch to LD8
xor al, al
mov cl, 0F6h
call Write_Reg
;clear watchdog timer
;watchdog disabled
xor al, al
mov cl, 30h
call Write_Reg
call Lock_Chip
ret
Disable_Watchdog Endp
;[]===============================================
56
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
; Name : Unlock_Chip
; IN : None
; OUT : None
;[]===============================================
Unlock_Chip Proc Near
Mov dx, 4Eh
mov al, 87h
out dx, al
out dx, al
ret
Unlock_Chip
Endp
;[]================================================
; Name : Lock_Chip
; IN : None
; OUT : None
;[]================================================
Unlock_Chip
Proc
Near
mov dx, 4Eh
mov al, 0AAh
out dx, al
ret
Unlock_Chip
Endp
;[]================================================
; Name : Write_Reg
; IN : CL - register index
;
AL - Value to write
; OUT : None
;[]================================================
Write_Reg Proc
Near
push
mov dx, 4Eh
mov al,cl
out dx,al
pop ax
ax
inc dx
out dx,al
ret
Write_Reg Endp
;[]================================================
IB935 User’s Manual
57
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
; Name : Read_Reg
; IN : CL - register index
; OUT : AL - Value to read
;[]=================================================
==
Read_Reg Proc
Mov al, cl
mov dx, 4Eh
out dx, al
Near
inc dx
in al, dx
ret
Read_Reg Endp
;[]================================================
58
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
D. Digital I/O Sample Code
Filename: W627hf.h
//=====================================================================
//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//=====================================================================
#ifndef __W627HF_H
#define __W627HF_H
//=====================================================================
#define W627_IOBASE 0x4E
//=====================================================================
1
#define
#define
W627HF_INDEX_PORT
W627HF_DATA_PORT
(W627_IOBASE+0)
(W627_IOBASE+1)
//=====================================================================
#define W627HF_REG_LD 0x07
//=====================================================================
#define W627HF_UNLOCK
#define W627HF_LOCK
0x87
0xAA
//=====================================================================
void Set_W627HF_LD( unsigned char);
void Set_W627HF_Reg( unsigned char, unsigned char);
unsigned char Get_W627HF_Reg( unsigned char);
//=====================================================================
#endif
//__W627HF_H
IB935 User’s Manual
59
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Filename: W627hf.cpp
//=====================================================================
//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//=====================================================================
#include "W627HF.H"
#include <dos.h>
//=====================================================================
void Unlock_W627HF (void);
void Lock_W627HF (void);
//=====================================================================
void Unlock_W627HF (void)
{
outportb(W627HF_INDEX_PORT, W627HF_UNLOCK);
outportb(W627HF_INDEX_PORT, W627HF_UNLOCK);
}
//=====================================================================
void Lock_W627HF (void)
{
outportb(W627HF_INDEX_PORT, W627HF_LOCK);
}
//=====================================================================
void Set_W627HF_LD( unsigned char LD)
{
Unlock_W627HF();
outportb(W627HF_INDEX_PORT, W627HF_REG_LD);
outportb(W627HF_DATA_PORT, LD);
Lock_W627HF();
}
//=====================================================================
void Set_W627HF_Reg( unsigned char REG, unsigned char DATA)
{
Unlock_W627HF();
outportb(W627HF_INDEX_PORT, REG);
outportb(W627HF_DATA_PORT, DATA);
Lock_W627HF();
}
//=====================================================================
unsigned char Get_W627HF_Reg( unsigned char REG)
{
unsigned char Result;
Unlock_W627HF();
outportb(W627HF_INDEX_PORT, REG);
Result = inportb(W627HF_DATA_PORT);
Lock_W627HF();
return Result;
}
//=====================================================================
File of the Main.cpp
60
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
//=====================================================================
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//=====================================================================
#include <dos.h>
#include <conio.h>
#include <stdio.h>
#include <stdlib.h>
#include "W627HF.H"
//=====================================================================
void ClrKbBuf(void);
int main (int argc, char *argv[]);
//=====================================================================
int main (int argc, char *argv[])
{
unsigned char ucDO = 0;
unsigned char ucDI;
unsigned char ucBuf;
//data for digital output
//data for digital input
Set_W627HF_LD( 0x07);
//switch to logic device 7
//clear
Set_W627HF_Reg(0xF1, 0x00);
ucDI = Get_W627HF_Reg(0xF1) & 0x0F;
ClrKbBuf();
while(1)
{
ucDO++;
Set_W627HF_Reg(0xF1, ((ucDO & 0x0F) << 4));
ucBuf = Get_W627HF_Reg(0xF1) & 0x0F;
if (ucBuf != ucDI)
{
ucDI = ucBuf;
printf("Digital I/O Input Changed. Current Data is 0x%X\n",ucDI);
}
if (kbhit())
{
getch();
break;
}
delay(500);
return 0;
}
}
//=====================================================================
void ClrKbBuf(void)
{
while(kbhit())
{
getch();
}
}
//---------------------------------------------------------------------------
IB935 User’s Manual
61
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
This page is intentionally left blank.
62
IB935 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
|