Integra DVD Player DPS 67 User Manual

DPS-6.7_En.book Page 1 Monday, July 31, 2006 3:12 PM

Super Audio CD & DVD Audio/Video Player

DPS-6.7

Instruction Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 3 Monday, July 31, 2006 3:12 PM

Precautions

1. Recording Copyright—Unless it’s for personal use

only, recording copyrighted material is illegal with-

out the permission of the copyright holder.

• Do not expose this unit to direct sunlight or heat

sources, because its internal temperature may

rise, shortening the life of the optical pickup.

• Avoid damp and dusty places, and places subject

to vibrations from loudspeakers. Never put the

unit on top of, or directly above a loudspeaker.

• Install this unit horizontally. Never use it on its

side or on a sloping surface, because it may cause

a malfunction.

• If you install this unit near a TV, radio, or VCR,

the picture and sound quality may be affected. If

this occurs, move this unit away from the TV,

radio, or VCR.

2. AC Fuse—The AC fuse inside the unit is not user-

serviceable. If you cannot turn on the unit, contact

your Integra/Onkyo dealer.

3. Care—Occasionally you should dust the unit all

over with a soft cloth. For stubborn stains, use a soft

cloth dampened with a weak solution of mild deter-

gent and water. Dry the unit immediately afterwards

with a clean cloth. Don’t use abrasive cloths, thin-

ners, alcohol, or other chemical solvents, because

they may damage the ﬁnish or remove the panel let-

tering.

8. To Obtain a Clear Picture—This unit is a high-

tech, precision device. If the lens on the optical

pickup, or the disc drive mechanism becomes dirty

or worn, the picture quality may be affected. To

maintain the best picture quality, we recommend

regular inspection and maintenance (cleaning or

worn part replacement) every 1,000 hours of use

depending on the operating environment. Contact

your Integra/Onkyo dealer for details.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SEC-

TION CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the

voltage requirements printed on the unit’s rear panel

(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

9. Moisture Condensation

The power cord plug is used to disconnect this unit

from the AC power source. Make sure that the plug

is readily operable (easily accessible) at all times.

Moisture condensation may damage this unit.

Read the following carefully:

Moisture may condense on the lens of the optical

pickup, one of the most important parts inside this

unit.

• Moisture condensation can occur in the following

situations:

Pressing the [Standby/On] button to select Standby

mode does not fully shutdown the unit. If you do not

intend to use the unit for an extended period,

remove the power cord from the AC outlet.

– The unit is moved from a cold place to a warm

place.

– A heater is turned on, or cold air from an air

conditioner is hitting the unit.

5. Never Touch this Unit with Wet Hands—Never

handle this unit or its power cord while your hands

are wet or damp. If water or any other liquid gets

inside this unit, have it checked by your Integra/

Onkyo dealer.

– In the summer, when this unit is moved from an

air conditioned room to a hot and humid place.

– The unit is used in a humid place.

• Do not use this unit when there’s the possibility

of moisture condensation occurring. Doing so

may damage your discs and certain parts inside

this unit.

If condensation does occur, remove all discs and

leave this unit turned on for two to three hours. By

this time, the unit will have warmed up and any con-

densation will have evaporated.

6. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you origi-

nally bought it.

• Do not leave rubber or plastic items on this unit

for a long time, because they may leave marks on

the case.

• This unit’s top and rear panels may get warm

after prolonged use. This is normal.

• If you do not use this unit for a long time, it may

not work properly the next time you turn it on, so

be sure to use it occasionally.

• When you’ve ﬁnished using this unit, remove all

discs and turn off the power.

7. Installing this Unit

• Install this unit in a well-ventilated location.

• Ensure that there’s adequate ventilation all

around this unit, especially if it’s installed in an

audio rack. If the ventilation is inadequate, the

unit may overheat, leading to malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 4 Monday, July 31, 2006 3:12 PM

Precautions—Continued

10. Region Numbers—The DVD standard uses region

numbers to control how discs can be played around

the world, the world being divided into six regions.

This unit will only play DVD discs that match its

region number, which can be found on its rear panel

For U.S. models

FCC Information for User

CAUTION:

The user changes or modiﬁcations not expressly

approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

ALL

(e.g.,

11. About this Manual—This manual explains how to

use all of this unit’s functions. Although the DVD

standard offers many special features, not all discs

use them all, so depending on the disc being played,

this unit may not respond to certain functions. See

the disc’s sleeve notes for supported features.

NOTE:

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interfer-

ence in a residential installation.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accor-

dance with the instructions, may cause harmful interfer-

ence to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful inter-

ference to radio or television reception, which can be

determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by

one or more of the following measures:

This unit contains a semiconductor laser system and is

classiﬁed as a “CLASS 1 LASER PRODUCT”. So, to

use this model properly, read this Instruction Manual

carefully. In case of any trouble, please contact the store

where you purchased the unit.

To prevent being exposed to the laser beam, do not try

to open the enclosure.

CAUTION:

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver.

CLASS 1M VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN. DO NOT VIEW

DIRECTLY WITH OPTICAL INSTRUMENTS.

•

Connect the equipment into an outlet on a circuit dif-

ferent from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV tech-

nician for help.

THIS PRODUCT UTILIZES A LASER. USE OF

CONTROLS OR ADJUSTMENTS OR PERFOR-

MANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARD-

OUS RADIATION EXPOSURE.

The label on the right is

applied on the rear panel.

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003.

For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

1. This unit is a CLASS 1

LASER PRODUCT and

employs a laser inside the cabinet.

2. To prevent the laser from being exposed, do not remove the

cover. Refer servicing to qualiﬁed personnel.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE

LA CLASSE B EST CONFORME À LA NORME

NMB-003 DU CANADA.

Sur les modèles dont la ﬁche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS

LARGE DE LA FICHE DANS LA BORNE CORRE-

SPONDANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 5 Monday, July 31, 2006 3:12 PM

Supplied Accessories

Make sure you have the following accessories:

RC-658DV

Remote controller & 2 batteries (AA/R6)

AV cable (RCA) (1.5 m)

cable (1.8 m)

This cable is used to connect the DVD player to other

-compatible Integra/Onkyo components for

(Remote Interactive) control.

To use

, in addition to an

connection, you must

make an analog audio connection (RCA) between the

DVD player and your Integra/Onkyo AV receiver.

Power cord (2 m)

Power-plug adapter

Only supplied in certain countries. Use this adapter if

your AC outlet does not match with the plug on the DVD

player’s power cord. (Adapter varies from country to

country.)

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 6 Monday, July 31, 2006 3:12 PM

Contents

Basic Operation

Advanced Operation

Playback Techniques

Overview

Important Safety Instructions...............................2

Precautions .........................................................3

Supplied Accessories..........................................5

Introduction..........................................................8

Features ..........................................................8

Disc Notes .......................................................9

Before Using the DVD player ............................12

Installing the Batteries ...................................12

Using the Remote Controller .........................12

Front & Rear Panels..........................................13

Front Panel....................................................13

Display...........................................................14

Rear Panel.....................................................15

Remote Controller .........................................16

Advanced Playback .......................................... 34

Selecting Chapters/Titles/Tracks/Folders

by Number.................................................. 34

Searching by Time........................................ 35

Repeat Playback........................................... 36

A-B Repeat Playback.................................... 36

Random Playback......................................... 37

Memory Playback ......................................... 38

Last Memory ................................................. 39

Zooming........................................................ 40

Selecting Camera Angles ............................. 40

Selecting Soundtracks .................................. 41

Selecting Subtitles ........................................ 41

Displaying Information .................................. 42

Connections

Detailed Settings

Connecting the DVD player...............................18

AV Cables & Connectors...............................18

Video Output/Video Setting Matrix ................19

Audio Output/Audio Setting Matrixes.............19

Before Making Any Connections ...................20

Basic Setup ...................................................20

Connecting Your TV (video only)...................21

Connecting to an AV Receiver ......................22

HDMI and Progressive Settings........................ 43

Setting the HDMI........................................... 43

Selecting Progressive or Interlaced .............. 43

Configuring the DVD player.............................. 44

Using the Onscreen Setup Menus................ 45

Picture Menu................................................. 46

Audio Menu................................................... 48

Language Menu............................................ 50

Display Menu ................................................ 52

Operation Setting Menu................................ 53

Connecting

-compatible Components......23

Connecting your HDTV or AV receiver

with an HDMI Input......................................24

Using the Multiroom Control Kits...................25

Connecting the Power/Turning

Miscellaneous information

on the DVD player .........................................26

Additional information ....................................... 55

Resetting the player...................................... 55

Adjusting the Display Brightness .................. 55

DVD-Video regions ....................................... 55

Disc Content Organization............................ 55

Glossary............................................................ 56

Troubleshooting................................................ 58

Specifications.................................................... 62

Getting Started and Setting up

Initial Setup........................................................27

First Time Setup ............................................27

Basic Playback

Playing Discs.....................................................28

Starting, Pausing & Stopping Playback.........28

Select Next & Previous track/chapter............29

Fast Forward & Reverse................................30

Forward Frame-by-Frame Playback..............30

Slow-motion Playback ...................................30

Navigating DVD & VCD Disc Menus .............31

Navigating CDs & Super Audio CDs .............31

Navigating MP3, WMA & DivX Discs.............32

Viewing a Slideshow of JPEG Images ..........33

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 7 Monday, July 31, 2006 3:12 PM

Contents—Continued

Thank you for purchasing the Integra/

Onkyo DPS-6.7 Super Audio CD & DVD

Audio/Video player. Read this manual care-

fully before using your new DVD player. A

good understanding of its features and oper-

ation will allow you to achieve optimum

performance and enjoyment.

Overview ..............................................2

Keep this manual for future reference.

Connections ......................................18

Getting Started and Setting up ........27

Basic Playback ..................................28

Playback Techniques ........................34

Detailed Settings...............................43

Miscellaneous information...............55

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 8 Monday, July 31, 2006 3:12 PM

Introduction

Features

*1 Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic” and the double-D symbol are trademarks

of Dolby Laboratories.

Highlights

• Dolby Digital, DTS

• DVD-Video, Video CD, audio CD

*2 “DTS” and “DTS Digital Out” are registered trademarks of

Digital Theater Systems, Inc.

®*4

• MP3, WMA, JPEG, DivX

(not North Amer-

*3 Windows Media, and the Win-

dows logo are trademarks, or

registered trademarks of

Microsoft Corporation in the

United States and/or other coun-

tries.

ican model)

• DVD-Audio and Super Audio CD

• CD-R/RW, DVD-R/RW, and DVD+R/RW com-

patible

• HDMI digital interface

*4 DivX, DivX Certiﬁed, and asso-

ciated logos are trademarks of

DivX, Inc. and are used under

license.

• 5.1-channel analog audio output

Video

• Advanced 108 MHz/14-bit video D/A converter

• 2 Components, 2 S-Video, and 2 composite video out-

puts

• Repeat/A-B Repeat/Random/Memory playback

• Supports 4:3 and 16:9 aspect ratio TVs

• Parental Lock function

*5 HDMI, the HDMI logo and

High-Deﬁnition Multimedia Interface are trademarks or regis-

tered trademarks of HDMI licensing LLC.

*6 VLSC and the VLSC logo are registered trademarks of Onkyo

Corporation.

• Screen Saver function

Audio

• 192 kHz/24-bit D/A converter

• Optical / Coaxial digital output

• VLSC (Vector Linear Shaping Circuitry) on all

channels

• Dynamic Range Control setting

Others

• Adjustable display brightness

• Full-function remote controller

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 9 Monday, July 31, 2006 3:12 PM

Introduction—Continued

• The DVD player does not support disc types not listed.

• The DVD player supports 8 cm and 12 cm discs.

• Don’t use discs with an unusual shape, such as those

shown below, because you may damage the DVD

player.

Disc Notes

Supported Discs

The DVD player supports the following discs.

Disc

Logo

Format or ﬁle type

DVD-Video

DVD-Audio

• Don’t use discs that have residue from adhesive tape,

rental discs with peeling labels, or discs with custom-

made labels or stickers. Doing so may damage the

DVD player and you may not be able to remove the

disc properly.

Super Audio

Super Audio CD (single

layer, dual layer, hybrid)

DVD-Video, MP3, WMA,

JPEG, MPEG4

DVD-R

About playing copy-controlled CDs

Some copy-controlled CDs may not conform to ofﬁcial

CD standards. They are special discs and may not play

on the DVD player.

DVD-Video, VR format ,

MP3, WMA, JPEG,

MPEG4

DVD-RW

Function Support

Video CD

Including PBC

PCM

The following icons are used throughout this manual to

indicate which functions can be used with the various

disc formats and ﬁle types.

Audio CD

Icon

Disc format or ﬁle type

Audio CD, MP3, WMA,

JPEG, DivX, MPEG4

CD-R

DVD-V

DVD-Video

DVD-A

SACD

DVD-Audio

Super Audio CD

DVD-VR mode

Video CD

Audio CD, MP3, WMA,

JPEG, MPEG4

CD-RW

JPEG CD

JPEG

DVD-VR

VCD

– DVD+R/RW –

The DVD player supports DVD+R/RW discs

recorded in the following formats:

• Discs recorded in DVD-Video mode.

Audio CD

• Discs recorded in ISO 9660 Level 2 or Joliet for-

mat containing MP3, WMA, or JPEG ﬁles.

MP3

JPEG

DivX

MP3 ﬁle

*1 The DVD player’s region number is printed on the rear panel.

If you attempt to play a disc intended for another region, the

message appears onscreen.

JPEG ﬁle

DivX (not North American model)

*2 MP3, WMA, and JPEG ﬁles are supported on discs recorded in

ISO 9660 Level 2 or Joliet format. (See “MP3/WMA/JPEG

Compatibility” on page 10 for more details.) However, some

CD-R, CD-RW, DVD-R, and DVD-RW discs may not work

properly for any of the following reasons: incomplete disc

ﬁnalization, disc burner characteristics, disc characteristics, the

disc is damaged or dirty, the total size of the data is too small.

Discs that contain different types of ﬁles, JPEG, MP3, WMA,

MPEG, DivX, and so on, are not supported. See the manual

supplied with your disc burner for more information. Conden-

sation or dirt on the optical pickup lens can also affect play-

back.

*3 The DVD player does not support DVD-VR discs that use

CPRM (Content Protection for Recordable Media).

*4 Some audio CDs feature copy protection that doesn’t conform

to the ofﬁcial CD standard. Since these are nonstandard discs,

they may not play properly in the DVD player.

About this Manual

This manual explains how to use all of the DVD player’s

functions. Although the DVD standard offers many spe-

cial features, not all discs use them all, so depending on

the disc being played, the DVD player may not respond

to certain functions. See your disc’s sleeve notes for sup-

ported features.

When you attempt to use a DVD feature that is

not available, this logo may appear onscreen,

indicating that the feature is not supported by

the current disc or by the DVD player.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 10 Monday, July 31, 2006 3:12 PM

Introduction—Continued

MP3/WMA/JPEG Compatibility

About DivX

• The DVD player can play/display MP3, WMA, and

JPEG ﬁles recorded on CD-R, CD-RW, DVD-R,

DVD-RW, DVD+R and DVD+RW discs.

• Discs must be in ISO 9660 Level 2 or Joliet format

(folders can be up to eight levels deep). Music ﬁles

recorded on discs that use the HFS (hierarchical ﬁle

system) cannot be played.

DivX is a compressed digital video format created by the

DivX® video codec from DivXNetworks, Inc. This

player can play DivX video ﬁles burned on CD-R discs.

When naming ﬁles on a disc prior to burning, keep in

mind that by default they will be played in alphabetical

order.

Note:

• Discs must be ﬁnalized.

• North American models do not support DivX Video.

• The DVD player can only recognize the ﬁrst session

on multisession discs.

DivX video compatibility

• You can determine the order in which the DVD player

plays/displays your MP3/WMA songs and JPEG pic-

tures by preﬁxing ﬁle and folder names with a three-

digit number. For example 001.Root, 002.Folder, and

so on, and 001.Track.mp3, 002.Track.mp3, and so on.

• Only the ﬁrst eight characters of folder and track names

(excluding the ﬁlename extension) are displayed.

• The folder numbered “001” appears as “ROOT” in the

Disc Navigator.

• The DVD player supports up to 255 folders and up to

255 ﬁles per folder.

• If you try to play an incompatible ﬁle, the message

“This format cannot be played” appears on the display.

• Ofﬁcial DivX Certiﬁed product.

• Plays DivX 5, DivX 4, DivX 3 and DivX VOD

video content (in compliance with DivX Certiﬁed

technical requirements).

DivX disc compatibility with this player is limited as

follows:

CD-R (650 MB/74 min. only)

Playable discs

CD-RW not recommended

Audio format

CBR MP3, VBR MP3, DivX AC3

Enhance video GMC, Opel, Progressive B-frames

■ MP3

Frame rate

8 to 25 fps

• MP3 ﬁles must be MPEG1Audio Layer 3 format, 44.1

or 48 kHz, ﬁxed bit-rate.

• MP3 ﬁles must have a “.mp3” or “.MP3” ﬁlename

extension.

CD physical

format

Mode 1, Mode 2 x A Form 1

ISO9660 Level 1, 2, or Joliet

File system

A ﬁle name should be in alphabet

and numerals only, and must incor-

porate “AVI” extension.

• Variable bit-rates (VBR) from 64 kbps to 320 kbps are

supported. (Playing times may display incorrectly

with VBR.)

File name

e.g. “*****.AVI”

■ WMA

Total number of

folders

Less than 255

• WMA ﬁles must have the copyright option turned off.

• Sampling rates 44.1/48 kHz are supported.

• Variable bit-rates (VBR) from 48 kbps to 192 kbps are

supported. (Playing times may display incorrectly

with VBR.)

Total number of

ﬁles

• WMA ﬁles must have a “.wma” or “.WMA” ﬁlename

extension.

■ JPEG

• JPEG ﬁles must have a “.jpg” or “.JPG” ﬁlename

extension.

• JPEG ﬁles must be less than 5 megabytes in size.

• JPEG ﬁles up to 5,700 x 3,800 pixels are supported.

About WMA

WMA is an acronym for Windows Media Audio and

refers to an audio compression technology developed by

Microsoft Corporation. WMA content can be encoded

by using Windows Media Player version 7/7.1 or 8.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 11 Monday, July 31, 2006 3:12 PM

Introduction—Continued

Handling Discs

• Never touch the underside of a disc.Always hold discs

by the edge, as shown.

It is forbidden by law to copy, broadcast, show, broadcast

on cable, play in public, or rent copyrighted material

without permission.

DVD-Video discs are copy-protected, and any record-

ings made from these discs will be distorted.

This product incorporates copyright protection technol-

ogy that is protected by method claims of certain U.S.

patents and other intellectual property rights owned by

Macrovision Corporation and other rights owners. Use

of this copyright-protection technology must be autho-

rized by Macrovision Corporation, and is intended for

home and other limited viewing uses only, unless other-

wise authorized by Macrovision Corporation. Reverse

engineering or disassembly is prohibited.

Underside

• Never attach adhesive tape or sticky labels to discs.

Cleaning Discs

• For best results, keep your discs clean. Fingerprints

and dust can affect the sound and picture quality and

should be removed as follows. Using a clean soft

cloth, wipe from the center outwards, as shown. Never

wipe in a circular direction.

✔

• To remove stubborn dust or dirt, wipe the disc with a

damp soft cloth, and then dry it with a dry cloth.

• Never use solvent-based cleaning ﬂuids, such as thin-

ner or benzine, commercially available cleaners, or

antistatic sprays intended for vinyl records, because

they may damage the disc.

Storing Discs

• Don’t store discs in places subject to direct sunlight, or

near heat sources.

• Don’t store discs in places subject to moisture or dust,

such as in a bathroom or near a humidiﬁer.

• Always store discs in their cases and vertically. Stack-

ing, or putting objects on unprotected discs may cause

warping, scratches, or other damage.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 12 Monday, July 31, 2006 3:12 PM

Before Using the DVD player

Installing the Batteries

Using the Remote Controller

To use the remote controller, point it at the DVD player’s

remote control sensor, as shown below.

Open the battery compartment, as shown.

Remote control sensor

DVD player

30˚

Insert the two supplied batteries (AA/R6)

in accordance with the polarity diagram

inside the battery compartment.

Notes:

• The remote controller may not work reliably if the

DVD player is subjected to bright light, such as direct

sunlight or inverter-type ﬂuorescent lights. Keep this

in mind when installing the DVD player.

• If another remote controller of the same type is used in

the same room, or the DVD player is installed close to

equipment that uses infrared rays, the remote control-

ler may not work reliably.

Close the battery compartment.

• Don’t put anything, such as a book, on the remote con-

troller, because the buttons may be pressed inadvert-

ently, thereby draining the batteries.

• The remote controller may not work reliably if the

DVD player is installed in a rack behind colored glass

doors. Keep this in mind when installing the DVD

player.

• The remote controller will not work if there’s an obsta-

cle between it and the DVD player’s remote control

sensor.

Notes:

• If the remote controller doesn’t work reliably, try

replacing both batteries.

• Don’t mix new and old batteries, or different types of

batteries.

• If you intend not to use the remote controller for a long

time, remove the batteries to prevent possible leakage

and corrosion.

• Flat batteries should be removed as soon as possible to

prevent possible leakage and corrosion.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 13 Monday, July 31, 2006 3:12 PM

Front & Rear Panels

For detailed information, refer to the pages in brackets.

Front Panel

1 2

3 4 5

7 8 9 J K L M

S R Q

P O

A Standby/On button [26]

This button is used to set the DVD player to On or

Standby.

J Open/Close button [28]

This button is used to open and close the disc tray.

K Pause button [28, 30]

B Standby indicator [26]

This button is used to pause playback.

This indicator lights up when the DVD player is in

Standby.

L Stop button [29]

This button is used to stop playback.

C Resolution button [43]

M Play button [28]

This button is used to select the video resolution for

the HDMI output, and select progressive or inter-

laced scanning.

This button is used to start playback.

N Down/Up

buttons [29]

The Down [

] button is used to select the previ-

D HDMI button [43]

ous chapter or track. During playback it selects the

beginning of the current track.

This button is used to turn HDMI on or off.

E HDMI indicator [43]

This indicator lights up when a HDMI signal is

being output.

The Up [

ter or track.

] button is used to select the next chap-

O Setup button [45]

F Disc tray [28]

This button is used to open and close the onscreen

setup menus.

Discs are loaded here.

G Top Menu button [31, 33]

P Return button

With DVD discs, this button displays the main

menu. With a JPEG disc, it displays thumbnails of

the images. With a Video CD, it turns PBC on or off.

This button is used to exit the onscreen setup.

Q Remote control sensor [12]

This sensor receives control signals from the remote

controller.

H Cursor

& Enter buttons [45]

The four cursor buttons located around the central

[Enter] button are used to navigate DVD-Video

menus and the onscreen setup menus.

The central [Enter] button is used to start playback

of the selected title, chapter, or track and to conﬁrm

settings.

R Display button [42]

This button is used to display information about the

current disc, title, chapter, or track, including the

elapsed time, remaining time, total time, and so on.

Press it repeatedly to display more information.

S Dimmer button [55]

I Menu button [31, 33]

This button is used to adjust the display brightness.

This button is used to display a menu on a DVD or

to open the Disc Navigator when using a JPEG disc,

or VR format DVD-RW disc.

normal

dim

dimmer

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 14 Monday, July 31, 2006 3:12 PM

Front & Rear Panels—Continued

Display

4 5678 9 0 A B C

DE F GH

9RANDOM indicator

D PRO LOGIC indicator

This indicator appears when using the Random

function.

The

D indicator appears when playing Dolby

Digital material. The PRO LOGIC indicator appears

when the DVD player’s Dolby Pro Logic decoder is

on.

0REMAIN indicator

This indicator appears while the remaining time is

being displayed.

2Disc type indicators

These indicators show the type of disc loaded.

ARepeat

indicator

3TITLE indicator

This indicator appears when A-B playback or repeat

playback is used.

While stopped, the total number of titles on the cur-

rent DVD-Video disc is displayed here. During

playback, the number of the current title is dis-

played.

BA-B indicator

These indicators appear when using the A-B Repeat

function.

4GROUP indicator

CCamera angle

indicator

While stopped, the total number of groups on the

current DVD-Audio disc is displayed here. During

playback, the number of the current group is dis-

played.

This indicator appears if the DVD-Video disc being

played features multiple camera angles.

DPROGRESSIVE indicator

This indicator appears when progressive video is

being output by the component video output.

5TRACK indicator

This indicator appears while track numbers are

being displayed. While stopped, the total number of

tracks on the current SACD, Video CD, audio CD,

or MP3/WMA disc are displayed. During playback,

the number of the current track is displayed.

EDTS indicator

This indicator appears when playing DTS material.

FPlay

indicator

This indicator is shown during playback.

65.1 CH indicator

GPause

indicator

This indicator appears when playing 5.1-channel

material.

This indicator appears when playback is paused.

HMP3 indicator

7CHP indicator

This indicator appears when playing an MP3 disc.

This indicator appears while the number of the cur-

rent chapter is being displayed.

IMessage & time area

Time information, such as total time, remaining

time, and so on, is displayed here in hours, minutes,

and seconds. Other messages are also displayed.

8D.MIX indicator

During multichannel audio playback, indicates that

the output signal has been down mixed from the

original audio source. This is an automatic function

performed by the player in order to present the most

appropriate audio mix to the speakers present in

your system.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 15 Monday, July 31, 2006 3:12 PM

Front & Rear Panels—Continued

Rear Panel

3 4 5 6 789

A AUDIO OUTPUT [20, 22, 23]

F COMPONENT 1 VIDEO OUTPUT [21]

These jacks output component video and can be

connected to an component video input on a TV or

projector.

These jacks make up the multichannel analog audio

output. The FRONT/D.MIX jacks can be connected

to a stereo input on a TV, hi-ﬁ amp, or other compo-

nent. The 1 and 2 jacks output the same signals, so

use either pair. If you use this connection, in the

Speaker Conﬁguration (page 48), set the Sub-

woofer, Center Speaker, and Surround Speaker set-

tings to Off, so that 5.1-channel DVD audio is down

mixed into two channels.

If you’re using an AV receiver or surround decoder

with a 5.1-channel analog audio input, use the

FRONT/D.MIX 1 or 2 jacks and the SURR 1 L/R,

CENTER, and SUBWOOFER jacks.

If you’re using an AV receiver or surround decoder

with a 7.1-channel analog audio input, connect the

SURR 2 L/R jacks to your amp’s surround back L/R

jacks, and set the SURR MODE switch to “1+2.”

The SURR 1 and SURR 2 jacks output the same

signals.

The DVD player has two component video outputs,

the COMPONENT 1 and COMPONENT 2, how-

ever, they output the same video signal.

G COMPONENT 2 VIDEO OUTPUT [21]

These BNC connectors can be used to connect a TV

or projector with BNC component video inputs.

The DVD player has two component video outputs,

the COMPONENT 1 and COMPONENT 2, how-

ever, they output the same video signal.

H OPTICAL DIGITAL AUDIO OUTPUT [22]

This optical digital audio output can be connected to

an optical digital audio input on a hi-ﬁ amp, AV

receiver, or surround sound decoder (Dolby Digital,

DTS).

I COAXIAL DIGITAL AUDIO OUTPUT [22]

This coaxial digital audio output can be connected

to a coaxial digital audio input on a hi-ﬁ amp, AV

receiver, or surround sound decoder (Dolby Digital,

DTS).

jack [23]

These

connected to the

gra/Onkyo AV components for interactive control.

Connecting an cable only does not make the

(Remote Interactive) connectors can be

connectors on your other Inte-

J AC INLET [26]

The supplied power cord is connected here. The

other of the power cord should be connected to a

suitable wall outlet.

system operational.You must also connect the audio

cables as well.

C RS 232

This port is for servicing.

K SURR MODE switch [23]

This switch is used to turn the AUDIO OUTPUT

SURR 2 on or off. To use this output, set the switch

to “1+2.” The SURR 2 jacks output the same signals

as the SURR 1 jacks.

D IR IN/OUT [25]

A commercially available IR receiver can be con-

nected to the IR IN jack, allowing you to control the

DVD player when it's out of sight, for example,

installed in a cabinet.

L HDMI OUT [24]

This HDMI output can be used to connect a TV or

projector with an HDMI input. This HDMI connec-

tor outputs digital audio and digital video.

A commercially available IR emitter can be con-

nected to the IR OUT jack to pass IR (infrared)

remote control signals along to other components.

M S VIDEO OUTPUT 1/2 [21]

E VIDEO OUTPUT 1/2 [20]

These connectors can be used to connect TVs or

projectors with S-Video inputs.

The DVD player has two S-Video output connec-

tors. They output the same video signal.

These RCA/phono connectors can be used to con-

nect TVs or projectors with composite video inputs.

The DVD player has two composite video output

connectors. They output the same video signal

respectively.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 16 Monday, July 31, 2006 3:12 PM

Front & Rear Panels—Continued

Remote Controller

A Standby button [26]

This button is used to set the DVD player to

Standby.

B On button [26]

This button is used to turn on the DVD player.

Don’t turn on the DVD player until you’ve com-

pleted, and double checked all connections

(pages 20–25).

C Number buttons [34, 35, 53]

These buttons are used to enter title, chapter, and

track numbers and to enter times for locating spe-

ciﬁc points in time.

D Audio button [41]

This button is used to select foreign language

soundtracks and audio formats (e.g., Dolby Digital

or DTS) on DVD-Video discs.

For Video CDs you can select left-channel, right-

channel, or stereo.

E Subtitle button [41]

This button is used to select subtitles on

DVD-Video discs.

F Random button [37]

This button is used with the Random function.

G Slow

buttons [30]

These buttons are used for slow-motion playback.

H Down/Up

buttons [29]

The Down [

] button is used to select the previ-

ous chapter or track. During playback it selects the

beginning of the current track.

The Up [

] button is used to select the next chap-

ter or track.

I FR/FF

buttons [30]

These buttons are used for fast reverse and fast for-

ward.

J Cursor

buttons [45]

These buttons are used to navigate onscreen menus.

K Menu button [31, 33]

This button is used to display a menu on a DVD or

to open the Disc Navigator when using a JPEG disc,

or VR format DVD-RW disc.

L Top Menu button [31, 33]

With DVD discs, this button displays the main

menu. With a JPEG disc, it displays thumbnails of

the images. With a Video CD, it turns PBC on or off.

M Aspect/Zoom button [40, 46]

This button is used to change the view mode. Press-

ing and holding it for a few seconds selects Zoom

mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 17 Monday, July 31, 2006 3:12 PM

Front & Rear Panels—Continued

N Open/Close

button [28]

This button is used to open and close the disc tray.

O Search button [34, 35]

This button is used to search for titles, chapters,

groups, folders, tracks, and speciﬁc points in time.

P Memory button [38]

This button is used with the Memory function.

Q Repeat button [36]

This button is used to set the Repeat function.

R A-B button [36]

This button is used to set the A-B Repeat function.

S CLR button [34, 35, 39]

This button is used to cancel various functions.

T Display button [42]

This button is used to display information about the

current disc, title, chapter, or track, including the

elapsed time, remaining time, total time, and so on.

Press it repeatedly to display more information.

U Angle button [40]

This button is used to select camera angles on

DVD-Video discs.

V Last Memory button [39]

This button is used with the Last Memory function.

W Pause

button [28, 30]

This button is used to pause playback. While play-

back is paused, pressing this button moves the video

forward one frame at a time.

X Play

button [28]

This button is used to start playback.

Y Stop button [29]

This button is used to stop playback.

Z Enter button [45]

This button is used to start playback of the selected

title, chapter, or track, and to conﬁrm settings.

a Return button

This button is used to exit the onscreen setup.

b Setup button [45]

This button is used to open and close the onscreen

setup menus.

c Resolution button [43]

This button is used to select a video resolution for

the HDMI OUT.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 18 Monday, July 31, 2006 3:12 PM

Connecting the DVD player

AV Cables & Connectors

Video

Cable

Jack

Description

HDMI connections can carry uncompressed, stan-

dard or high deﬁnition digital video and digital

audio, for the best picture and sound quality.

HDMI

Component video separates the luminance (Y) and

color difference signals (PR, PB), providing the best

picture quality. Some TV manufacturers label their

component video inputs differently.

/ C^R

/ CR

Component

video

The DVD player has RCA/phono and BNC compo-

nent video outputs.

/CB

/CR

P^R

/C^R

S-Video provides better picture quality than com-

posite video.

S-Video

S VIDEO

VIDEO

Composite

video

(supplied)

Composite video can be found on virtually all TVs,

VCRs, and video equipment.

Audio

Cable

Jack

Description

Optical digital audio connections provide better

audio quality than analog connections.

Optical digital

Coaxial digital

OPTICAL

Coaxial digital audio connections provide better

audio quality than analog connections.

COAXIAL

RCA analog audio connectors can be found on vir-

tually all AV components.

Analog

(supplied)

This cable carries multichannel analog audio and

it’s typically used to connect DVD players with

individual 5.1 channel analog audio outputs. Sev-

eral standard analog audio cables can be used

instead of a multichannel cable.

FRONT/D. MIX

SURR1

CENTER

Multichannel

analog audio

cable (RCA)

SUB

WOOFER

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 19 Monday, July 31, 2006 3:12 PM

Connecting the DVD player—Continued

Video Output/Video Setting Matrix

The following matrix shows how the video outputs work in relation to the various video settings.

HDMI Output Setting (page 27)

Setting

On (default)

Off

Progressive Setting (page 43)

HD Resolution setting (page 43)

480p/576p

(default)

Video output

Auto

720p, 1080i

Progressive

No output

Interlaced

HDMI

No output

✓

Component

S-Video

No output

✓

No output

✓

Composite

*1 Depending on the native resolution of your TV, you may get no picture.

*2 If your TV doesn’t support progressive scanning, you’ll get no picture.

*3 If your TV doesn’t support the HD Resolution settings of 720p and 1080i, you’ll get no picture.

Audio Output/Audio Setting Matrixes

■ Digital Audio Output/Audio Setting Matrix

The following matrix shows how the digital audio outputs work in relation to the Digital/HDMI Audio Out setting.

Setting

Digital/HDMI Audio Out setting (page 48)

Digital

audio output

All (default)

PCM

Off

HDMI

No output

✓

Digital (optical & coaxial)

Audio from SACDs is not output by the HDMI OUT or optical or coaxial digital audio outputs. It’s only output by the analog

audio outputs. Audio from the multichannel area of a DVD-Audio disc is also only output by the analog audio outputs.

*a If your TV or amp doesn’t support higher sampling rates, set the Linear PCM Out setting to Down Sample On (page 48).

*b Dolby Digital and DTS sources will be converted to PCM. If your TV or amp doesn’t support Dolby Digital and DTS, choose this

option.

■ Analog Audio Output/Audio Setting Matrix

The following matrix shows the recommended audio settings for each analog audio output.

Speaker Conﬁguration (page 48)

SACD Audio Setup (page 49)

Setting

5.1 channel (default):

2 channel:

Subwoofer: Off

Front: Large

Center: Off

Subwoofer: On

Front: Small

Center: Small

Surround: Small

DSD (default)

PCM

Analog audio

output

Surround: Off

2-channel (FRONT/D.MIX)

Multichannel

✓

*c If your TV or multichannel amp has a Dolby Pro Logic decoder built in, by setting the Downmix Setting (page 50) to Lt/Rt,

multichannel sources can be down mixed and output as an Lt/Rt mix.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 20 Monday, July 31, 2006 3:12 PM

Connecting the DVD player—Continued

Before Making Any Connections

• Read the manuals supplied with your AV components.

• Don’t connect the power cord until you’ve completed

all audio and video connections.

The supplied AV cable is made up of an analog audio

cable and a composite video cable.

Analog audio

Right (red)

Left (white)

Right (red)

Left (white)

Optical Digital Outputs

The DVD player’s optical digital connectors have a shut-

ter-type cover that opens when an optical plug is

inserted, and closes when it’s removed. Push the plug in

all the way.

Caution: To prevent shutter damage, hold the optical

plug straight when inserting and removing.

Composite video

(Yellow)

Right!

• Push each plug in all the way to

make a good connection (loose

connections can cause noise or

malfunctions).

• To prevent interference, keep

audio and video cables away from

power cords and speaker cables.

RCA AV Connection Color Coding

Wrong!

RCA AV connections are usually color coded: red,

white, and yellow. Use red plugs to connect right-chan-

nel audio inputs and outputs (typically labeled “R”). Use

white plugs to connect left-channel audio inputs and out-

puts (typically labeled “L”). And use yellow plugs to

connect composite video inputs and outputs.

Basic Setup

The setup described here is a basic setup that allows you to play discs using just the cables supplied with the player. In

this setup, stereo audio is played through the speakers in your TV.

This player is equipped with copy pro-

tection technology. Do not connect this

player to your TV via a VCR using AV

cables, as the picture from this player

will not appear properly on your TV.

AV cable

(Supplied)

ANALOG

INPUT

(This player may also not be compati-

ble with some combination TV/VCRs

for the same reason; refer to the manu-

VIDEO IN

facturer for more information.)

Power cord

(Supplied)

To power outlet

1. Connect the VIDEO OUTPUT and AUDIO OUTPUT FRONT/D.MIX 1 jacks to a set of AV inputs on your TV.

Use the supplied AV cable (RCA), connecting the red and white plugs to the audio outputs and the yellow plug to

the video output.

The DVD payer has two composite video output connectors and two pairs of stereo analog audio output connectors.

They output the same video and audio signals respectively.

See the following page if you want to use other cable for the video connection.

2. Connect the supplied AC power cord to the AC INLET, then plug into a power outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 21 Monday, July 31, 2006 3:12 PM

Connecting the DVD player—Continued

Using Component Video

ConnectingYour TV (video only)

You can use the component video output instead of the

standard video out jack to connect this player to your TV

(or other equipment).

This will provide better quality picture than S-Video.

• Use a RCA/phono or BNC component video cable

(not supplied) to connect the COMPONENT 1 or 2

VIDEO OUTPUT jacks to a component video input

on your TV (or monitor orAV receiver). The COMPO-

NENT 1 and 2 jacks output the same video signals, so

use either pair.

If you connect the component video output to a TV or

another component that doesn’t support progressive

scanning, be sure to turn off HDMI (see page 43).

You can set the component video output to Progressive

or Interlaced (see page 43).

• Connect the DVD player directly to your TV. If you

connect the DVD player through a VCR, TV/VCR

combination, or video selector, the picture may be dis-

torted because DVD-Video discs are usually copy pro-

tected.

Using S-Video

If your TV (or other equipment) has an S-Video input,

you can use this instead of the standard (composite) out-

put for a better quality picture.

• Use an S-Video cable (not supplied) to connect the S

VIDEO 1 or 2 OUTPUT to an S-Video input on your

TV (or monitor or AV receiver). The S VIDEO 1 and

2 jacks output the same video signals, so use either.

Line up the small triangle above the jack with the same

mark on the plug before plugging in.

COMPONENT

S VIDEO

COMPONENT

VIDEO IN

S VIDEO IN

Compatibility of this unit with progressive-scan TVs.

This player is compatible with progressive video Macro

Vision System Copy Guard.

CONSUMERS SHOULD NOTE THAT NOT ALL

HIGH DEFINITION TELEVISION SETSARE FULLY

COMPATIBLE WITH THIS PRODUCT AND MAY

CAUSE ARTIFACTS TO BE DISPLAYED IN THE

PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE

SCAN PICTURE PROBLEMS, IT IS RECOM-

MENDED THAT THE USER SWITCH THE CON-

NECTION TO THE “STANDARD DEFINITION”

OUTPUT. IF THERE ARE QUESTIONS REGARD-

ING OUR TV SET COMPATIBILITY WITH THIS

MODEL 525p AND 625p DVD PLAYER, PLEASE

CONTACT OUR CUSTOMER SERVICE CENTER.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 22 Monday, July 31, 2006 3:12 PM

Connecting the DVD player—Continued

Connecting the Analog Output

Connecting to an AV Receiver

Connect the FRONT/D.MIX 1 or 2AUDIO OUTPUT

jacks on this player to a set of analog audio inputs on

your AV receiver with the supplied AV cable (RCA).

The FRONT/D.MIX 1 and 2 jacks output the same sig-

nals, so use either pair.

Step 1: Audio Connection

You can connect the DVD player to your AV receiver

using the multichannel analog audio output or one of

the digital audio outputs. In addition, you should also

connect a 2-channel analog audio output for compati-

bility all certain discs.

AV receiver

Step 2:Video Connection (See pages 20–21)

You may also want to connect the DVD player’s video

output to your AV receiver and connect the AV

receiver’s video output to a video input on your TV.

You can use any of the DVD player’s video outputs.

Typically, you must use the same type of video cable

to connect your DVD player to your AV receiver as

you do to connect your AV receiver to your TV.

FRONT/D. MIX

^FRONTL

Before Connecting

• Before making any connections, turn off the DVD

player and AV receiver, and disconnect them from the

wall outlets. Failure to do so may result in speaker

damage.

Note:

Connection Hints

• If you use this connection, in the Speaker Conﬁgura-

tion (page 48), set the Subwoofer, Center Speaker, and

Surround Speaker settings to Off, so that multichannel

audio sources are down mixed into two channels.

• To enjoy Dolby Digital or DTS surround sound, you

must connect the DVD player to your AV receiver by

using an optical or coaxial digital audio cable or

HDMI cable. See page 24 for HDMI connection infor-

mation.

• To record the audio from a CD-R disc to a cassette

deck or CDR recorder that’s connected to the AV

receiver, or if you want to use your AV receiver’s

Zone 2 function, you must connect the DVD player’s

stereo analog audio output to your AV receiver.

• If your AV receiver has an analog multichannel input,

we recommend that you connect it to the DVD

player’s multichannel analog output. This will ensure

that you can enjoy all types of discs, including Dolby

Digital and DTS DVD-Video discs, and DVD-Audio

and SACD discs containing multichannel audio at

higher sampling rates.

Connecting the Digital Output

Connect one of the DIGITALAUDIO OUTPUT jacks

on this player to a digital input on your AV receiver.

COAXIAL

OPTICAL

COAXIAL

Connect one

or the other

AV receiver

If your AV receiver doesn’t support Dolby Digital and

DTS, set the Digital/HDMI Audio Out setting to PCM.

See page 48, and also refer to the operating instructions

that came with your AV receiver.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 23 Monday, July 31, 2006 3:12 PM

Connecting the DVD player—Continued

Connecting the Multichannel Analog

Output

Connecting

Components

-compatible

Connect the DVD player’s FRONT/D.MIX 1 or 2,

SURR 1, CENTER, and SUBWOOFER jacks to the

multichannel analog audio input on your AV receiver.

You can use three stereo audio cables for this.

FRONT/D. MIX

REMOTE

CONTROL

AUDIO OUTPUT

ANALOG

FRONT/D. MIX

SURR1 CENTER

SUB

WOOFER

REMOTE

CONTROL

FRONT

SUB

CENTER

AV receiver

SURR

• The remote controller supplied with Integra/Onkyo

AV receiver or ampliﬁers can be used to control the

DVD player.

AV receiver

• The function of the upper and lower

are the same. Connect to either one.

connectors

• To use

, in addition to an

connection, you must

■ IfYour AV Receiver has a 7.1-channel Analog

also make an analog audio connection (RCA) between

the DVD player and your other

nents.

Audio Input

-capable compo-

Connect the DVD player’s SURR 1 jacks to your AV

receiver’s surround input jacks, and connect the

SURR 2 jacks to your AV receiver’s surround back

input jacks. The SURR 1 and SURR 2 outputs output

the same signals.

When you make this connection, set the SURR MODE

switch to “1+2.”

If you use this connection, the output level will be

reduced by 3 dB (i.e., the volume level will be reduced

slightly).

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 24 Monday, July 31, 2006 3:12 PM

Connecting the DVD player—Continued

Notes:

Connecting your HDTV or AV

receiver with an HDMI Input

• The DVD player supports HDCP (High-bandwidth

Digital Content Protection), a protection system for

digital video. HDMI components that you connect to

the DVD player must also support HDCP.

This section shows how to connect the DVD player to a

AV receiver, HDTV, or projector that has an HDMI input

socket.

• The DVD player supports High-Deﬁnition Multime-

dia Interface Speciﬁcation Information Version 1.0.

What is HDMI?

HDMI & the DVD player

HDMI (High Deﬁnition Multimedia Interface) is a new

connection format that can carry uncompressed, stan-

dard or high deﬁnition digital video and digital audio.

Until now, several separate video and audio cables have

been required to connect AV components together. With

HDMI, a single cable is all that’s necessary to achieve

the best picture and audio quality.

HDMI video is compatible with DVI (Digital Visual

Interface). To send HDMI video to a DVI input requires

an HDMI-to-DVI cable. The DVD player supports

HDCP (High-bandwidth Digital Content Protection),

and for an HDMI-to-DVI connection to work, the other

component must also support it. Note that this may not

work with some DVI components.

■ Video

The DVD player’s HDMI OUT supports the following

video resolutions:

• 720 x 480p (progressive), 60 Hz

• 720 x 576p (progressive), 50 Hz (not North American

model)

• 1280 x 720p (progressive), 50/60 Hz

• 1920 x 1080i (interlaced), 50/60 Hz

If the connected HDTV or projector doesn’t support a

resolution, you may get no picture.

On the DVD player, you can select a resolution suitable

for use with the connected HDTV or projector (see

page 43).

Using HDMI

Use the HDMI cable (not supplied) to connect the DVD

player’s HDMI OUT to an HDMI input on your AV

receiver. Alternatively, you can connect the DVD player

directly to the HDMI input on your TV.

■ Audio Formats

The DVD player’s HDMI OUT supports the following

audio formats:

• PCM (96 kHz, 48 kHz, 44.1 kHz)

• Dolby Digital

• DTS

If your HDMI-compatible TV or projector doesn’t sup-

port Dolby Digital and DTS, the HDMI OUT will not

output digital audio in that format. In this case, set the

Digital/HDMI Audio Out setting to PCM (see page 48).

If your TV doesn’t support digital audio at high sampling

rates, set the Linear PCM Out setting to Down Sample

On, so that it’s down sampled to below 48 kHz (see

page 48).

Signal ﬂow

HDMI

HDTV,

projector

HDMI

HDMI cable

Note that audio from SACD discs is not output by the

HDMI OUT. For this format, you need to use the analog

multichannel output (see page 23).

(not supplied)

AV receiver

HDMI

HDTV,

HDMI

projector

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 25 Monday, July 31, 2006 3:12 PM

Connecting the DVD player—Continued

Using a Multiroom Kit with Other

Components

Using the Multiroom Control Kits

To control the DVD player with the remote controller

when DVD player is located in a cabinet, you’ll need a

commercially available multiroom remote control kit.

• Multiroom kits are made by Niles and Xantech.

These kits can also be used when control other compo-

nents.

In this setup, an IR emitter is connected to the DVD

player’s IR OUT jack and placed in front of the other

component’s remote control sensor. Infrared signals

received at the DVD player’s IR IN jack are fed through

to the other component via the IR emitter. Signals picked

up by the DVD player’s remote control sensor are not

output.

Using a Multiroom Kit with a Cabinet

In this setup, the IR receiver picks up the infrared signals

from the remote controller and feeds them to the DVD

player located in the cabinet via the connecting block.

IR Receiver

Connecting

block

IR IN

IR OUT

DVD player

IR Emitter

IR Receiver

Connecting

block

Remote controller

Other component

IR IN

DVD player

Signal ﬂow

The IR emitter should be connected to the DVD player’s

IR OUT jack, as shown below.

Inside

cabinet

Remote controller

Other component

Signal ﬂow

Remote control

Miniplug cable

The miniplug cable from the connecting block should be

connected to the DVD player’s IR IN jack, as shown

below.

sensor

Emitter

Miniplug

Miniplug cable

IR Emitter

From the connecting block

DVD player

Signal ﬂow

DVD player

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 26 Monday, July 31, 2006 3:12 PM

Connecting the Power/Turning on the DVD player

Before connecting

• Before unplugging the player from the

• Make sure that all the connections on pages 18–25 are

power outlet, make sure you ﬁrst

complete (the connection to a TV is required).

switch it into standby.

• For the above reasons, do not plug this

player into a switched power supply

found on some ampliﬁers and AV

receivers.

Standby/On

Standby indicator

To a wall

outlet

Standby

Press [Standby/On] button on the

DVD player or [On] on the remote

controller.

Turn on your TV and select the

input through which the DVD

player is connected.

The DVD player turns on and the

Standby indicator turns off.

Remote

controller

• To put the DVD player in the standby

mode, press [Standby/On] on the DVD

player, or [Standby] on the remote

controller.

• While the Standby indicator lights up,

the DVD player can receive signals

from the remote controller.

• Setting the [Standby/On] button to

standby does not shut off the power

completely.

Note:

• This player features a screen saver and an auto power

off function. If the player is stopped and no button is

pressed for 15 minutes, the screen saver starts (see

page 52). If the disc tray is closed but no disc is play-

ing and no control is pressed for 20 minutes, the player

automatically goes into standby (see page 54).

Plug the supplied power cord into

the AC INLET and then into the

power outlet on the wall.

• Do not use a power cord other than the

one supplied with the DVD player. The

power cord supplied is designed for

use with the DVD player and should

not be used with any other device.

• Never have the power cord discon-

nected from the DVD player while the

other end is plugged into the wall out-

let. Doing so may cause an electric

shock. Always connect by plugging

into the wall outlet last and disconnect

by unplugging from the wall outlet

ﬁrst.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 27 Monday, July 31, 2006 3:12 PM

Initial Setup

This chapter explains the settings you need to make the

very ﬁrst time the DVD player is turned on.

Use the Up and Down [ ]/[

buttons to select “On” or “Off”

for “HDMI Output Setting.”

]

Remote

controller

Select “On” to use the HDMI output.

Initial Setup

TV Shape

: 4:3 Letter box

HDMI Output Setting

✔

On-Screen Language

Off

Enter

The “On-Screen Language” menu

appears next.

Use the Up and Down [ ]/[

buttons to select a language, and

then press [Enter].

]

Remote

controller

See page 50 for more information on

the language options.

First Time Setup

Initial Setup

The very ﬁrst time you turn on the DVD player, the Ini-

tial Setup menu appears onscreen.

TV Shape

: 4:3 Letter box

HDMI Output Setting

On-Screen Language

: On

✔

English

Initial Setup

TV Shape

Français

Español

Deutsch

Italiano

✔

4:3 Letter box

HDMI Output Setting

4:3 Pan Scan

On-Screen Language

16:9 Widescreen

16:9 Compressed

The Initial Setup menu closes and the

setup is complete.

The DVD player is now ready to use.

Note:

• You can cancel the Initial Setup by pressing the Open/

Close [ ] button, and complete the settings later by

using the onscreen setup menus (see page 44).

Here you need to make a few settings to get the DVD

player up and running. You can change these settings

later (see page 44).

Use the Up and Down [ ]/[

buttons to select aTV shape, and

then press [Enter].

]

Remote

controller

Select “4:3 Letter box” or “4:3 Pan

Scan” if you have a 4:3 TV. Select

“16:9 Widescreen” or “16:9 Com-

pressed” if you have a widescreen TV.

See page 46 for more information.

Initial Setup

TV Shape

✔

4:3 Letter box

HDMI Output Setting

4:3 Pan Scan

On-Screen Language

16:9 Widescreen

16:9 Compressed

The “HDMI Output Setting” menu

appears next.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 28 Monday, July 31, 2006 3:12 PM

Playing Discs

This chapter covers basic playback. Advanced playback

functions are covered in the next chapter.

Press Open/Close

The disc tray closes and the relevant disc

type indicator appears on the display.

Important:

• Throughout this manual, the term DVD refers to DVD-

Video, DVD-Audio, DVD-R/RW, and DVD+R/RW

discs. When a function is speciﬁc to a particular type

of DVD disc, it will be speciﬁed.

Tip:

Remote

controller

If you press the Play [ ] button, the disc

tray will close and, depending on the

type of disc, playback will start automat-

ically.

Pause

Stop

Open/Close

Play

• For details on playing JPEG picture

discs, see “Viewing a Slideshow of

JPEG Images” on page 33.

Note:

• Only load discs that are supported by the DVD player.

See pages 9 to 11.

Open/

Starting, Pausing & Stopping

Playback

Pause

Play

Down

This section explains how to start, pause, and stop

playback.

Stop

■ Start

To start playback, press the Play

] button.

[

Playback starts and the Play indica-

tor appears on the display.

If you’re playing a DVD-Video disc, or

a VCD with PBC (Playback Control),

you may need to start playback from a

menu (see page 31).

Press Open/Close

disc tray.

to open the

Remote

controller

See page 32 for more on MP3 discs.

Remote

controller

■ Pause

To pause playback, press the

Pause [ ] button.

Playback pauses and the Pause indi-

cator appears on the display.

Load a disc.

To resume playback, press the Play [

button.

]

Load a disc with the label side facing up,

using the disc tray guide to align the disc

(if you’re loading a double-sided DVD

disc, load it with the side you want to

play face down).

Remote

controller

Playback resumes and the Pause

indicator disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 29 Monday, July 31, 2006 3:12 PM

Playing Discs—Continued

Select Next & Previous track/chapter

■ Stop

To stop playback, press the Stop

] button.

[

DVD-A

SACD

VCD

MP3

DivX

DVD-V

DVD-VR

WMA

Playback stops and the Play indica-

tor disappears.

The North American model does not support DivX.

This section explains how to skip to the next and previ-

ous track and chapter.

• When you stop playback of a

DVD-Video disc or VCD, the DVD

player remembers the point at which

playback was stopped and “Resume”

appears onscreen. To resume play-

back from that point, press the Play

Remote

controller

■ Select

During Playback, press the Up

] button to select next track/

[

track/

chapter.

chapter

The Next track/chapter starts playback.

[

] button. To cancel the Resume

function, press the Stop [ ] button

again. The Resume function is reset

when the disc is removed from the

DVD player.

Remote

controller

• With the Last Memory function you

can resume playback from any point

even if the disc has been removed

(see page 39).

■ Select

During Playback, press the Down

] button to select previous

tack/chapter.

The ﬁrst press selects the beginning of

the current track.

Notes:

Previous [

track/

chapter

• Prolonged display of the same picture or menu may

cause irreparable damage to your TV screen known as

screen burn-in. To prevent this, don’t keep playback

paused for too long and always press the Stop [ ] but-

ton when you’ve ﬁnished playing a DVD-Video disc

or VCD. The DVD player features a screen saver to

protect your TV from the effects of burn-in (see

page 52).

Remote

controller

• With some DVD-Video discs, you may experience

picture noise that is not normally visible with standard

TV broadcasts. This is usually because DVD-Video

uses a lot of high-resolution video data. The amount of

noise, if any, will depend on your particular TV and

the problem can sometimes be alleviated by turning

down the TV’s sharpness control.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 30 Monday, July 31, 2006 3:12 PM

Playing Discs—Continued

Forward Frame-by-Frame Playback

DivX

DVD-VR

VCD

DVD-V

The North American model does not support DivX.

With frame-by-frame playback you can view individual

picture frames one at a time forward.

Pause

Slow

Play

■ Forward

frame-by-

frame

Press the Pause [ ] button.

Press it repeatedly to view sub-

sequent frames.

Remote

To resume normal playback, press the

Play [ ] button.

controller

Slow-motion Playback

Fast Forward & Reverse

DVD-V

DVD-VR

DivX

VCD

DivX

DVD-A

SACD

VCD

MP3

DVD-V

DVD-VR

The North American model does not support DivX.

With slow-motion playback you can watch a scene

slowly either forward or backward.

The North American model does not support DivX.

This section explains how to fast forward and reverse.

■ Fast

forward

During playback, press the FF

] button to start fast forward.

Playback fast forwards and “ x2”

appears onscreen.

■ Forward During playback or paused,

[

slow

press the Slow Forward [ ] but-

ton.

Remote

controller

motion

Forward slow-motion playback starts

and “ 1/2” appears onscreen.

To change the slow-motion speed, press

the Slow Forward [ ] button repeat-

edly to cycle through the speeds:

1/2, 1/4, 1/6, 1/8.

Remote

controller

To change the fast-forward speed, press

the FF [ ] button repeatedly to select:

x2, x4, x8, x16.

To resume normal playback, press the

Play [ ] button.

To resume normal playback, press the

Play [ ] button.

■ Fast

During playback, press the FR

reverse

[

] button to start fast reverse.

Playback reverses and “ x2” appears

onscreen.

To change the fast-reverse speed, press

the FR [ ] button repeatedly to

select: x2, x4, x8, x16.

Remote

controller

■ Backward During playback or paused,

slow

press the Slow Back [ ] button.

Backward slow-motion playback starts

and “ 1/2” appears onscreen.

To change the slow-motion speed, press

the Slow Back [ ] button repeatedly to

cycle through the speeds:

motion

Remote

controller

To resume normal playback, press the

Play [ ] button.

1/2, 1/4, 1/6, 1/8.

Note:

To resume normal playback, press the

Play [ ] button.

• Fast forward and fast reverse cannot be used with

WMA ﬁles.

Note:

• Backward slow-motion playback cannot be used with

DivX and MPEG ﬁles.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 31 Monday, July 31, 2006 3:12 PM

Playing Discs—Continued

Notes:

, Enter

Top Menu

• Not all DVDs and VCDs have menus.

• Menu operation varies from disc-to-disc. See the

disc’s sleeve notes for details.

• On some DVDs, to display the disc menu, press the

[Menu] button.

• For DVD-VR discs, press the [Top Menu] button to

display the program menu, or press the [Menu] button

to display the playlist, if available. Use the Up and

Down [ ]/[ ] buttons to select the program that you

want to play, and press the [Enter] button to start play-

back.

Number

buttons

To set VCD’s PBC on and off

PBC menus can turned on or off by pressing the [Top

Menu] button.

Down

Enter

Navigating CDs & Super Audio CDs

Tep Menu

This section explains how to play audio CDs and Super

Audio CDs with the Disc Navigator.

Load an audio CD or Super Audio

CD.

Navigating DVD & VCD Disc Menus

The Disc Navigator appears.

DVD-V

VCD

DVD-A

Stop

Disc CD

DVD-Video discs usually have a menu from which you

can select titles, chapters, and other options, including

soundtracks, subtitles, and audio formats (e.g., Dolby

Digital or DTS). VCDs that support PBC (Playback

Control) may also have an onscreen menu.

/Track01.CDA

001. Track01

002. Track02

003. Track03

004. Track04

005. Track05

006. Track06

007. Track07

008. Track08

Repeat

:Off

Random :Off

Load a DVD or VCD.

With DVD, a menu usually appears

automatically. If it doesn’t, try pressing

the [Top Menu] button.

The tracks are displayed.

Use the Up and Down [ ]/[

buttons to select a track, and

press [Enter] to start playback.

With SACDs, you can select the multi-

channel area, 2-channel area, or CD

layer by pressing the [Audio] button.

]

WithVCDs that support PBC, you may

have to press the Play [ ] button to dis-

play the menu.

Remote

controller

On a DVD menu, use the arrow

[

], [ ], [ ], [ ] buttons to

Remote

select an item, and then press

[Enter].

controller

On a VCD menu, use the number

buttons to select the tracks.

If the VCD’s menu consists of several

pages, use the Up [

] and Down

[

] buttons to view them. During

playback, you can return to the menu

by pressing the [Return] button.

Note:

• During random playback or memory playback, the

arrow buttons cannot be used.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 32 Monday, July 31, 2006 3:12 PM

Playing Discs—Continued

Use the Up and Down [ ]/[

buttons to select tracks and sub-

folders in the open folder.

]

Remote

controller

To open a folder in the list, press the

[Enter] button. To close a folder (i.e.,

move back up the directory tree), press

the [Return] button. Alternatively,

select the item at the top of the list and

press the [Enter] button.

Use the Left and Right [ ]/[ ] buttons

to display the other folders that contain

playable tracks.

Play

Enter

Return

To play the selected track, press

the Play [ ] or [Enter] button.

If available, the ID3 tag information,

(Title name, Artist name, Album name,

and so on) will scroll across the bottom

of the screen.

Remote

controller

Navigating MP3, WMA & DivX Discs

MP3

WMA

DivX

The North American model does not support DivX.

This section explains how to play MP3, WMA, and

DivX ﬁles with the Disc Navigator.

Play

2/3

Disc DATA

3/11

00:00:29 00:03:58 00:04:27

/mp3/Track03.MP3

002. mp3

Repeat

:Off

001. Track01

002. Track02

003. Track03

004. Track04

005. Track05

006. Track06

007. Track07

Random :Off

Load an MP3, WMA, or DivX disc.

The Disc Navigator appears.

Stop

Disc DATA

1/3

/mp3

-/5

Name: Onkyo Artist Name: Onkyo Album Name: Onkyo

001. ROOT

002. mp3

For MP3 playback

Repeat

:Off

Random :Off

003. MP3 music

001. Track01

002. Track02

003. Track03

004. Track04

005. Track05

Subsequent tracks in the same folder

are played in order.

Press the Stop [ ] button to stop

playback.

Remote

controller

Initially, the folders in the root direc-

tory are displayed.

The DVD player numbers folders and

tracks in hierarchical order.You can use

these numbers to select folders and

tracks directly with the Search function

(see page 34).

Note:

• During random playback or memory playback, the

arrow buttons cannot be used.

To open a folder, use the Up and

Down [ ]/[ ] buttons to select

it, and then press [Enter].

Remote

controller

The contents of the folder are dis-

played.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 33 Monday, July 31, 2006 3:12 PM

Playing Discs—Continued

Viewing a Slideshow of JPEG Images

Use the Left and Right [ ]/[ ] buttons

to display other folders that contain

JPEG images.

JPEG

This section explains how to display a slideshow of

JPEG images on your TV.

To play a slideshow, press the

Play [ ] or [Enter] button.

Subsequent images are displayed in

order, with each image being displayed

for ﬁve seconds.

Remote

controller

Load a JPEG disc.

The Disc Navigator appears.

Stop

Disc DATA

To display an image for longer, press

the Pause [ ] button. Press the Play

1/17

/jpg

-/-

001. jpg

Repeat

:Off

002. image0

003. image1

004. image2

005. image3

001. 001

[

] button to resume.

Random :Off

Use the Down and Up [

]/[

] but-

tons to view the previous or next image.

To ﬂip a picture 180 degrees, use the

Up and Down [ ]/[ ] buttons (not

while zoomed in).

002. 002

003. 003

Initially, the folders in the root direc-

tory are displayed.

To rotate a picture counterclockwise or

clockwise, use the Left and Right [ ]/

[ ] buttons (not while zoomed in).

To zoom in or out, use the [ ] and

The DVD player numbers folders and

ﬁles in hierarchical order. You can use

these numbers to select folders and ﬁles

directly with the Search function (see

page 34).

[

] buttons. While zoomed in, use the

[ ]/[ ]/[ ]/[ ] buttons to move

around the picture.

To open a folder, use the Up and

Down [ ]/[ ] buttons to select

it, and then press [Enter].

To stop the slideshow, press the

Stop [ ] or [Menu] button.

The slideshow stops automatically

when all pictures have been displayed.

Remote

controller

Remote

controller

The contents of the folder are dis

played.

Use the Up and Down [ ]/[

buttons to select images and

subfolders in the open folder.

]

■ To display thumbnails

Remote

controller

To display thumbnails, in step 3, after opening the folder

you want to display, press the [Top Menu] button.

Use the arrow [ ], [ ], [ ], [ ] buttons to select the

thumbnails, and press [Enter] to start a slideshow. Press

the [Menu] button to return to the Disc Navigator.

A thumbnail-size preview for the cur-

rently selected image is displayed.

DATA

1/17

Disc DATA

-/-

/image1/001.JPG

005. image1

001. 001

002. 002

003. 003

004. 004

005. 005

006. 006

007. 007

■ About HD JPEG

Repeat

:Off

Random :Off

If your TV is connected via HDMI and the HDMI reso-

lution is set to 720p or 1080i, you can view your JPEG

images in high deﬁnition (see page 47).

W: 150 H: 120

To open a folder in the list, press the

[Enter] button. To close a folder (i.e.,

move back up the directory tree), press

the [Return] button. Alternatively,

select the item at the top of the list and

press the [Enter] button.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 34 Monday, July 31, 2006 3:12 PM

Advanced Playback

Use the number buttons to spec-

ify a title, chapter, or track num-

ber.

Remote

controller

To enter, for example, “12,” press the

[1] button followed by the [2] button.

Number

buttons

Title

Chapter

Disc

DVD-VIDEO Current/Total 12/ 19 Current/Total 5/

Entered title number

appears here

Play

Entered chapter number

appears here

Enter

If you’re playing a DVD, MP3, WMA,

JPEG, or DivX disc and you want to

select a chapter, track, or ﬁle in another

title, group, or folder, press the Left [ ]

button to select and enter the number of

that title, group, or folder ﬁrst.

To clear a number, press the [CLR] but-

ton.

Selecting Chapters/Titles/Tracks/

Folders by Number

DVD-A

SACD

VCD

MP3

WMA

JPEG

DivX

DVD-V

DVD-VR

Press the Play [ ] or [Enter] but-

ton to start playback of the spec-

iﬁed title, chapter, or track.

Remote

controller

The North American model does not support DivX.

With the Search function you can select chapters, titles,

and tracks by number.

Press the [Search] button.

The Search window appears onscreen.

Remote

controller

This is what appears for DVDs.

Title

Chapter

Disc

DVD-VIDEO Current/Total 1/ 19 Current/Total - - -/ 78

Notes:

This is what appears for CDs.

• During playback, you can select other chapters or

tracks directly by using the number buttons (i.e., with-

out pressing the [Search] button). For example, to

select chapter #2, simply press [2]. To select chapter

#10, press [+10] and [0].

Track

Disc

CDDA

Current/Total - -/ 10

• DVD-Video discs usually have menus for selecting

titles and chapters.

• When Video CD PBC is on, you can’t search for

tracks. Turn PBC off ﬁrst.

• The [Search] button cannot be used during random

playback or memory playback.

• Search may not work with some discs.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 35 Monday, July 31, 2006 3:12 PM

Advanced Playback—Continued

Press the Play [ ] or [Enter] but-

ton to start playback of the spec-

iﬁed time.

Remote

controller

Number

buttons

Play

Notes:

Enter

• In some cases, playback may start from a slightly dif-

ferent point to the one that you specify.

• Time search may not work with some discs.

• Time search cannot be used while a DVD-Video or

Video CD menu is displayed onscreen.

• The [Search] button cannot be used during random

playback or memory playback.

Searching by Time

DVD-A

SACD

VCD

DVD-V

DVD-VR

With the Search function you can search by time.

During playback, press the

[Search] button twice.

The Search window appears onscreen.

Remote

controller

Time

Disc

DVD-VIDEO

-:- -:- -

Use the number buttons to enter

a time.

Time search only works within the cur-

rent title or track.

Remote

controller

To enter, for example, 5 minutes, 30

seconds, press [5] [3] [0] buttons.

Time

Disc

DVD-VIDEO

-:-5:30

To clear a number, press the [CLR] but-

ton.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 36 Monday, July 31, 2006 3:12 PM

Advanced Playback—Continued

Notes:

• Repeat playback may not work with some discs.

• The Repeat function can be used in combination with

the Random function (see page 37).

• If the Memory function is on (see page 38), the select-

able options are Memory Repeat, which plays the

playlist repeatedly, and Repeat Off.

Repeat

A–B

A-B Repeat Playback

DVD-V

DVD-VR

MP3

DivX

SACD

VCD

Play

The North American model does not support DivX.

With the A-B Repeat function you can play a speciﬁed

section over-and-over again.

During playback, press the [A-B]

button to set the A point (i.e., the

start of the section you want to

Remote

controller

Repeat Playback

repeat).

DVD-A

SACD

VCD

MP3

WMA

JPEG

DivX

DVD-V

DVD-VR

“Repeat A-” appears onscreen and

A indicator appears on the display.

The North American model does not support DivX.

With the Repeat function you can play a disc, title, chap-

ter, group, track, or folder over-and-over again.

Press the [A-B] button again to

set the B point (i.e., the end of the

section you want to repeat).

Playback repeats between the A and B

points, and “Repeat A-B” appears

Remote

controller

Press the [Repeat] button repeat-

edly to select a repeat option.

The selected repeat option appears

Remote

controller

onscreen and

AB indicator

onscreen.

appears on the display.

The available options depend on the

type of disc, as follows:

DVD-Video, DVD-VR: Chapter

Repeat, Title Repeat, Disc Repeat,

Repeat Off.

To cancel A-B repeat playback,

press the [A-B] button.

Remote

controller

DVD-Audio: Track Repeat, Group

Repeat, Disc Repeat, Repeat Off.

SACD, VCD, CD: Track Repeat, Disc

Repeat, Repeat Off.

MP3, JPEG, WMA, DivX: Track

Repeat, Folder Repeat, Disc Repeat,

Repeat Off.

Notes:

• The A-B Repeat function may not work with some

DVD-Video discs and VCDs that support PBC.

• In some cases, the A and B points may be at slightly

different points to the ones that you specify.

Press the Play [ ] button to start

repeat playback.

Remote

controller

To cancel repeat playback, use

the [Repeat] button to select

“Repeat Off.”

Remote

controller

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 37 Monday, July 31, 2006 3:12 PM

Advanced Playback—Continued

Press the Play [ ] button to start

random playback.

If you set the Random function during

playback, random playback begins

after the current chapter or track has

ﬁnished.

Remote

controller

Random playback stops automatically

when all of the items have been played

once.

If the Repeat function is on (see

page 36), random playback starts all

over again when all items have been

played.

Random

Play

To cancel random playback, use

the [Random] button to select

“Random Off.”

Remote

controller

Random Playback

DVD-V

DVD-A

DVD-VR

VCD

MP3

WMA

SACD

With the Random function you can enjoy a random

selection of titles, chapters, groups, tracks, or folders.

Notes:

• Random playback may not work with some discs.

Press the [Random] button

repeatedly to select a random

option.

• To use the Random function with aVCD that supports

PBC, you must ﬁrst turn off PBC (see page 31).

Remote

controller

• If the Memory function is on (page 38), random play-

back is unavailable.

The selected random option appears

onscreen.

• You can’t use the [Search] button during random play-

back.

The options available depends on the

type of disc, as follows:

• During random playback, the remote controller’s

arrow [ ], [ ], [ ], [ ] buttons and number buttons

don’t work with the Disc Navigator.

DVD-Video, DVD-VR: Title Random,

Disc Random, Random Off.

DVD-Audio: Group Random, Disc

Random, Random Off.

• The Random function cannot be used with JPEG ﬁles.

SACD, VCD, CD: Disc Random, Ran-

dom Off.

• For DVD-Audio discs, the Up [

used during random playback.

] button cannot be

MP3, WMA: Folder Random, Disc

Random, Random Off.

With the Title Random option, chapters

within the current title are played at

random. With the Disc Random option,

titles, chapters, groups, tracks, or fold-

ers on the disc are played at random.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 38 Monday, July 31, 2006 3:12 PM

Advanced Playback—Continued

Repeat step 2 to add more items

to the memory list.

You can add up to 32 items to the mem-

ory list.

Memory

CLR

To play the memory list, press

the Play [ ] button.

Remote

Last

Memory

controller

The Memory Play Setup window must

be open when you press the Play [

button.

]

Play

Stop

Enter

To stop playback, press the Stop

] button.

While playback is stopped, you can

delete the memory list by pressing the

[CLR] button.

[

Remote

controller

While playback is stopped, you can

cancel the Memory Playback function

by pressing the Stop [ ] button again.

Memory Playback

DVD-V

DVD-VR

VCD

MP3

WMA

SACD

DivX

The North American model does not support DivX.

With the Memory Playback function you can create your

own memory list of titles, chapters, and tracks.

Adding New Items to the List

Press the [Memory] button.

The Memory List window appears

onscreen, as shown.

Use the Up/Down [ ]/[ ] buttons

Remote

controller

to select the step before which

you want to insert the new item,

and then press the [Enter] but-

ton.

Remote

controller

Memory List

Title/Folder

Current/Total 001 / 019 Current/Total --- / 078

No.

Chapter/Track

--- / 019

--- / 078

Memory List

Title/Folder

Current/Total 001 / 019 Current/Total --- / 078

No.

Chapter/Track

005 / 019

002 / 019

--- / 019

003 / 019

010 / 019

--- / 019

001 / 078

012 / 078

--- / 078

004 / 078

003 / 078

--- / 078

The top row ( ) is used to enter title/

folder and chapter/track numbers.

The steps in the memory list are num-

bered.

Enter the title/folder, and chapter/

track numbers of the item to be

inserted.

Use the remote controller’s Left/Right

[ ]/[ ] buttons to select the parame-

ters, and use the number buttons to

enter the number.

Remote

controller

Enter the title/folder, and chapter/

track numbers of the item you

want to add to the memory list,

and then press [Enter].

Use the remote controller’s Left/Right

[ ]/[ ] buttons to select the parame-

ters, and use the number buttons to

enter the number.

To add the all titles, folders, chapters, or

tracks on the disc, select the parameter

and press [+10] button.

The new item is added to the memory

list as step 01.

Remote

controller

Press the [Enter] button.

The new item is inserted into the mem-

ory list and subsequent items move

down the list.

Remote

controller

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 39 Monday, July 31, 2006 3:12 PM

Advanced Playback—Continued

Deleting Items from the List

Last Memory

DVD-V

Remote

controller

Use the Up/Down [ ]/[ ] buttons

to select it, and then press the

[CLR] button.

With the Last Memory function you can resume play-

back from where you left off even if the disc has been

removed and the DVD player has been set to Standby.

Last Memory also remembers the soundtrack and subti-

tle settings you were using.

The item is deleted and subsequent

items move up the list.

Editing Steps

During DVD playback, press the

[Last Memory] button.

The last memory point for the disc is

stored, “LAST MEM” appears on the

display.

Use the Up/Down [ ]/[ ] buttons

to select the step.

Remote

controller

Remote

controller

If the [Last Memory] button is pressed

again, the last memory point is updated.

To stop playback, press the Stop

Remote

controller

[

] button.

Use the Left/Right [ ]/[ ] buttons

and number buttons to edit the

title/folder or chapter/track num-

bers, and then press [Enter].

Now you may remove the disc

and turn off the DVD player.

Remote

controller

To resume playback, load the

disc, and then press the Play [

button.

]

Remote

controller

The Last Memory dialog box appears.

Last Memory is set.

Start playback from memory location?

Notes:

Yes

Memory Clear

• To close the Memory List window, press the [Return]

button.

• The memory list will be deleted when the DVD player

is set to Standby or the disc tray is opened.

• To use this function with a VCD that supports PBC,

you must ﬁrst turn off PBC.

• The Memory Playback function cannot be used with

some discs.

To resume playback from the last

memory point, select “Yes,” and

then press [Enter].

Remote

controller

To start playback from the beginning,

select “No,” and then press [Enter].

To start playback from the beginning

and delete the last memory point, select

“Memory Clear,” and then press

[Enter].

• JPEG images can be added to the memory list, how-

ever, they will not be displayed.

Notes:

• The Last Memory function can store the last point for

up to six DVDs. When you set the Last Memory func-

tion for a seventh disc, the ﬁrst disc’s settings are

deleted.

• The Last Memory function will not work while a

menu is being displayed onscreen.

• The Last Memory function may not work with some

DVDs.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 40 Monday, July 31, 2006 3:12 PM

Advanced Playback—Continued

Selecting Camera Angles

DVD-V

Some DVDs feature multiple camera angles that allow

you to view scenes from different angles. When a DVD

features multiple camera angles, the camera indicator

appears on the display. Such discs usually have the cam-

era angle logo ( ) printed on the sleeve.

Angle

Play

Stop

Press the [Angle] button repeat-

edly to cycle through the avail-

able camera angles.

Remote

controller

The number of the currently selected

camera angle appears onscreen. For

example, on a disc with three camera

angles, you’d see 1/3, 2/3, and 3/3.

Zoom

Notes:

Zooming

• With some DVDs you may not be able to select differ-

DVD-VR

JPEG

ent camera angles even though the camera

tor is displayed.

indica-

DVD-V

VCD

With the Zoom function you can enlarge any part of the

picture.

• With some DVDs you can select camera angles from

a menu.

During playback or while play-

back is paused, press and hold

the [Zoom] button for 2 seconds.

Remote

controller

The picture is enlarged.

Press the [Zoom] again repeat-

edly to Zoom in.

Remote

The number of zoom steps available

controller

depends on the resolution of the disc or

ﬁle.

After the maximum zoom, the picture

returns to its normal size.

To see other areas of the picture

while zoomed, use the remote

Remote

controller

controller’s arrow [ ], [ ], [ ],

[

] buttons.

Notes:

• The Zoom function may not work with some discs.

• The Zoom function can also be used during slow-

motion playback.

• The Zoom function cannot be used with HD JPEG.

• The Zoom function cannot be used with disc menus.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 41 Monday, July 31, 2006 3:12 PM

Advanced Playback—Continued

Selecting Subtitles

DVD-V

DivX

The North American model does not support DivX.

Some DVD-Video discs feature subtitles in several lan-

guages. See the disc’s sleeve notes for details.

During playback, press the [Sub-

title] button repeatedly to cycle

through the available subtitles.

Audio

Subtitle

Remote

controller

The name of the selected subtitle

appears onscreen for several seconds.

To turn off subtitles, use the [Subtitle]

button to select “Off.”

Notes:

Selecting Soundtracks

• When you stop playback and cancel the Resume func-

tion (see page 28), the subtitle language will revert to

your default subtile language (see page 50), or the

disc’s default subtitle language.

DVD-A

VCD

SACD

DVD-V

Some DVD-Video discs feature soundtracks in several

languages or audio formats (e.g., Dolby Digital or DTS).

Music DVD-Video discs and DVD-Audio discs some-

times feature audio in several formats, such as PCM,

Dolby Digital, or DTS. See the disc’s sleeve notes for

details.

• With some DVDs you can select subtitles from a

menu, and you may not be able to select subtitles dur-

ing playback.

During playback, press the

[Audio] button repeatedly to

Remote

controller

cycle through the available

soundtracks.

The name of the selected soundtrack

appears onscreen for several seconds.

With VCDs, you can select Stereo,

Mono L (left), Mono R (right), or Mix.

With SACDs you can select Multichan-

nel area, 2 channel area, or CD layer.

Notes:

• With DVD-Video discs, when you stop playback and

cancel the Resume function (see page 28), the

soundtrack language will revert to your default lan-

guage (see page 50), or the disc’s default language.

• With some discs, selecting another soundtrack may

cause the picture to skip momentarily.

• With some DVDs you need to select soundtracks from

a menu, and you may not be able to select other

soundtracks during playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 42 Monday, July 31, 2006 3:12 PM

Advanced Playback—Continued

■ Audio CD, Super Audio CD

Displaying Information

Onscreen:

You can display various information about the current

disc, title, chapter, or track as follows.

• Current/total track number, elapsed track time,

remaining track time, and total track time.

• Current/total track number, elapsed disc time, remain-

ing disc time, and total disc time.

During playback, press the [Dis-

play] button repeatedly to cycle

though the information.

Display:

• Elapsed track time

• Remaining track time

• Elapsed disc time

• Remaining disc time

Various information appears onscreen.

The operating status (e.g., Stop, Play,

Resume) and disc type information is

displayed along the top of the screen.

Remote

controller

■ MP3, WMA

Onscreen:

• Current/total folder number, current/total track num-

ber in the folder, elapsed track time, remaining track

time (MP3 only), and total track time (MP3 only).

The information displayed depends on the type of disc,

as follows:

Display:

• File name

■ DVD-Video, DVD-VR

• Folder name

Onscreen:

• Total number of folders

• Elapsed track time

• Current/total title number, elapsed title time, remain-

ing title time, total title time, selected soundtrack,

selected subtitle, and the number of available camera

angles.

• Current/total chapter number, elapsed chapter time,

remaining chapter time, and total chapter time.

■ DivX

Onscreen:

• Current/total track number, elapsed track time,

remaining track time, total track time, selected

soundtrack, and selected subtitle.

Display:

• Remaining title time

• Elapsed chapter time

• Elapsed title time

Display:

• File name

• Folder name

■ DVD-Audio

• Total number of folders

• Elapsed track time

Onscreen:

• Current/total track number, elapsed track time,

remaining track time, total track time, selected

soundtrack, and selected subtitle.

• Current/total group number, elapsed group time,

remaining group time, and total group time.

Display:

• Remaining track time

• Elapsed track time

■ Video CD

Onscreen:

• Current/total track number, elapsed track time,

remaining track time, and total track time.

Display:

• Elapsed track time

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 43 Monday, July 31, 2006 3:12 PM

HDMI and Progressive Settings

Resolution

HDMI

Resolution

Note:

Setting the HDMI

• Be sure to choose a resolution that’s supported by your

TV. If you select a resolution that your TV doesn’t

support, there will be no picture.

This section explains how to turn on the HDMI OUT and

change the video resolution when your TV or projector

is connected to the HDMI OUT.

Press the DVD player’s [HDMI]

button to turn on HDMI.

Selecting Progressive or Interlaced

If your TV supports progressive video, you can set the

DVD player to progressive and enjoy progressive video

on your TV. If your TV doesn’t support progressive

video, set the DVD player to interlaced.

While the HDMI OUT is on, the component video out-

put is ﬁxed at progressive and depending on the selected

resolution there may be no output, so turn off the HDMI

OUT before changing this setting.

Press the [Resolution] button

repeatedly to change the HDMI

resolution.

The ﬁrst button press displays the cur-

rent resolution onscreen. Press the but-

ton again while the resolution is

Remote

controller

displayed to change the setting.

Press the DVD player’s [HDMI]

button to turn off HDMI.

Use the [Resolution] button to

select progressive or interlaced.

The ﬁrst button press displays the cur-

rent setting onscreen. Press the button

again while the setting is displayed to

The DVD player supports the following resolutions:

Auto:

The resolution is automatically set to the native resolu-

tion of the TV connected to the HDMI OUT.

If the DVD player does not support the TV’s native res-

olution setting, the resolution 480p/576p will be used.

change the setting.

Remote

controller

The PROGRESSIVE indicator appears

on the display when progressive is

selected.

480p (480p/576p) (default):

The setting displayed depends on the country in which

you purchased the DVD player.

720 × 480p 60Hz or 720 × 576p 50Hz

Also output by the DVD player’s analog video outputs.

With this setting, component video output will be pro-

gressive.

720p:

1280 × 720p 50/60Hz

Not output by the DVD player’s analog video outputs.

1080i:

1920 × 1080i 50/60Hz

Not output by the DVD player’s analog video outputs.

Tip:

These settings can also be changed by using the onscreen

setup menus (see pages 46, 47).

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 44 Monday, July 31, 2006 3:12 PM

Conﬁguring the DVD player

This chapter explains the various functions and settings of the onscreen setup menus.

Functions and settings are arranged into six menus: Picture, Audio, Language, Display, Operation Setting, and Initial.

The following table lists all the functions and settings, with a brief description and page number where you can ﬁnd full

details.

Setting

Description

Page #

TV Shape

Select the aspect ratio that matches your TV.

Stretch the picture to ﬁt your TV screen.

Turn HDMI video output on or off.

View Mode

HDMI Output Setting

Set the component video output to progressive or

interlaced.

Progressive Setting

HD Resolution

Picture

Select the video resolution for the HDMI OUT.

For displaying JPEG images at a high resolution on a

HDTV.

HD JPEG Mode

Video Black Level

Brightness

Choose a video black level.

Adjust the picture brightness.

Adjust the picture sharpness.

Sharpness

PAL Output Setting (not North

American model)

Convert the disc’s video format to NTSC or PAL.

Settings for the digital signal output by the optical,

coaxial, and HDMI digital audio outputs.

Digital/HDMI Audio Out

Linear PCM Out

Select whether or not the DVD player down samples

digital audio.

Subwoofer

Front Speaker

Center Speaker

Surround Speaker

Conﬁgure the speakers settings for the multichannel

analog audio output.

Audio

Test tone for adjusting the level of each channel of

your amp’s multichannel input.

Test Tone

Center delay

Delay for the multichannel output’s center and sur-

round jacks.

Surr. delay

Dynamic Range Control

Set the Dynamic Range function.

Determines how the built-in Dolby Pro Logic decoder

works.

Dolby Pro Logic Setting

Determines whether DSD or PCM is output when

playing SACDs.

SACD Audio Setup

Downmix Setting

Dolby and DTS downmix settings.

Select a language for the onscreen setup menus and

messages.

On-Screen Language

Language

Disc Menu Language

Audio Language

Select your preferred language for disc menus.

Select your preferred language for soundtracks.

Select your preferred language for subtitles.

Subtitle Language

DivX Subtitle (not North Ameri-

can model)

Select your preferred language for DivX subtitle.

Turn on or off onscreen messages and indicators.

On-Screen Display

Display

Select a color for onscreen setup menus and mes-

sages.

On-Screen Display Color

Select a background color for when playback is

stopped.

Background

Screen Saver

Set the Screen Saver function.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 45 Monday, July 31, 2006 3:12 PM

Conﬁguring the DVD player—Continued

Setting

Description

Page #

Parental Lock

Security Code

Set the Parental Lock function.

Change the security code for use with parental lock.

Determines what's played on DVD-Audio discs with

DVD-Video contents.

Operation

Setting

DVD Priority Contents

Determines how the SACD multichannel and 2-chan-

nel area and the CD area are played.

SACD Priority Contents

Auto Power Off

Sets the Auto power off function.

DivX Registration (not North

American model)

Displays your DivX VOD registration code

Initial Setup

TV Shape

This menu appears automatically the very ﬁrst time

you turn on your DVD player. (These settings are

available in other menus.)

HDMI Output Setting

On-Screen Language

Using the Onscreen Setup Menus

This section explains how to navigate the onscreen setup menus.

Press the [Setup] button.

The onscreen setup menu appears, as

shown.

Picture

TV Shape

: 4:3 Letter box

: Normal

: Off

View Mode

HDMI Output Setting

Progressive Setting

HD Resolution

HD JPEG mode

Video Black Level

Brightness

: Interlace

: 480p

: Off

: Light

: Level 4

Sharpness

Progressive Conversion : Auto

Use the arrow [ ]/[ ]/[ ]/[

]

Enter

buttons to navigate the menus,

and press the [Enter] button to

see the available options.

Setup

Use the Up/Down [ ]/[ ] buttons

to select the options, and press

the [Enter] button to conﬁrm your

selection.

When you’ve ﬁnished, press the

[Setup] button again.

The onscreen setup menu closes.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 46 Monday, July 31, 2006 3:12 PM

Conﬁguring the DVD player—Continued

View Mode

Picture Menu

With this setting you can adjust the aspect of the picture

so that it ﬁts your TV screen. Due to your TV’s aspect

ratio setting and the DVD’s aspect ratio, black bars may

appear above and below the picture or at the sides and the

aspect of the picture may be unsuitable. In this case, use

this setting to adjust the aspect of the picture as you like.

TV Shape

With this setting you can select a picture format to match

the aspect ratio of your TV.

4:3 Letter box (default): Choose

this option if you have a standard

TV (4:3 aspect ratio). When you

watch widescreen DVD-Video

Normal (default): The picture is displayed in its

original aspect ratio.

movies, the entire picture will be

visible and there will be black

View Mode 1: The picture is stretched horizontally

to make it ﬁt the height of the screen.

bars at the top and bottom of the screen, as shown.

View Mode 2: The picture is stretched vertically to

4:3 Pan & Scan:Choose this

make it ﬁt the width of the screen.

option if you have a standard TV

(4:3 aspect ratio) and want to use

the full height of the screen when

watching widescreen

View Mode 3: The picture is stretched horizontally

and vertically to make it ﬁt the screen.

Tip:

The view mode can also be changed by

using the remote controller’s [Aspect]

button.

DVD-Video movies. In order to

use the full height of the screen, the picture will be

cropped on both sides, as shown. This option won’t

work with discs that don’t support pan and scan.

Note:

• This setting does not apply to DVD menus.

16:9 Widescreen: Choose this option if you have a

widescreen TV (16:9 aspect ratio). Depends on TV,

the picture appears stretched when watching programs

in 4:3 format.

HDMI Output Setting

With this setting you can turn the HDMI video output on

or off. See page 43 for more information.

16:9 Compressed: Choose

this option if you have a

On (default): Video is output by the HDMI OUT.

Off: Video is not output by the HDMI OUT.

widescreen TV (16:9 aspect

ratio) and the picture appears

stretched when watching

programs in 4:3 format. This

option will correct the issue.

Tip:

This setting can also be changed by using the [HDMI]

button on the front panel (see page 43).

Note:

Notes:

• When this setting is set to On, video is output by the

analog video outputs only when the HD Resolution is

set to 480p/576p.

• This setting does not apply to DVD menus.

• When the HDMI OUT signal is at a resolution of 720p

or 1080i, programs in 4:3 format will appear stretched,

so we recommend that you select the 16:9 Com-

pressed option.

Progressive Setting

With this setting you can set the component video output

to progressive or interlaced. While the HDMI Output

Setting is set to On, this setting is ﬁxed at Progressive

and cannot be changed. See page 43 for more informa-

tion.

• With some DVD-Video discs this setting may have no

effect. See the disc’s sleeve notes to see which picture

format is used.

Interlaced: Component video output is interlaced.

Progressive: Component video output is progressive.

Tip:

When the HDMI Output Setting is set to Off, you can

also change this setting by using the [Resolution] button

on the front panel (see page 43).

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 47 Monday, July 31, 2006 3:12 PM

Conﬁguring the DVD player—Continued

HD Resolution

Brightness

With this setting you can set the video resolution for the

HDMI OUT. See page 43 for more information.

With this setting you can adjust the picture brightness.

Level 1-7: 1 is the darkest. 7 is the brightest. The

Auto: The resolution is automatically set to the

native resolution of the TV connected to the HDMI

OUT.

default brightness is 4 (standard).

Sharpness

480p (480p/576p) (default): The setting displayed

depends on the country in which you purchased the

DVD player.

With this setting you can adjust the picture sharpness.

Level 1-7: 1 is the softest. 7 is the sharpest. The

default sharpness is 4 (standard).

720 x 480p 60 Hz or 720 x 576p 50 Hz

720p: 1280 x 720p 50/60 Hz

1080i: 1920 x 1080i 50/60 Hz

PAL Output Setting (Not North American

model)

Tip:

With this setting you can specify how the DVD player

outputs video signals when playing NTSC format

DVD-Video discs or Video CDs.

When the HDMI Output Setting is set to On, you can

also change this setting by using the [Resolution] button

on the front panel (see page 43).

AUTO (default): Use this option if your TV supports

both PAL and NTSC. The DVD player does not con-

vert the video format. When you play a PAL disc, the

video output will be PAL format. And when you play

an NTSC disc, it’ll be NTSC format.

Note:

• Initially, the DVD player is conﬁgured to output both

HDMI and analog video. However, if after changing

the resolution settings there’s no picture, with the ana-

log video connection or HDMI connection in place,

press the [Resolution] button repeatedly to restore the

picture.

NTSC: Use this option if your TV doesn’t support

PAL playback, or the picture is distorted when

watching PAL discs. The DVD player will convert

PAL format video signals to NTSC-compatible for-

mat.

HD JPEG mode

If your TV is connected to the HDMI OUT and the

HDMI resolution is set to 720p or 1080i, this setting

allows you to display your JPEG pictures in high deﬁni-

tion.

PAL: Use this option if your TV doesn’t support

NTSC playback, or the picture is distorted when

watching NTSC discs. The DVD player will convert

NTSC format video signals to PAL-compatible for-

mat.

On: JPEG pictures displayed in high deﬁnition.

Off (default): JPEG pictures displayed as normal.

Note:

• If you select the wrong setting by mistake and loose

the picture, while pressing and holding the Up

button, press the [Standby/On] button to return to the

previous setting.

Notes:

• If your TV is connected to a video output other than

the HDMI OUT, or the HDMI output resolution is set

to something other than 720p or 1080i, even if this set-

ting is set to On, your JPEG pictures will not be dis-

played in high deﬁnition.

• When using HD JPEG, it may take a while to display

each picture. And the Zoom function cannot be used.

Also, onscreen status messages such as “Play” and

“Stop” are not displayed.

Video Black Level

With this setting you can adjust the picture blackness for

the analog video outputs. It does not affect the compo-

nent video output when its set to progressive.

Light: Blacks are lighter, and the entire picture

becomes lighter.

Dark: Blacks are darker, and the entire picture

becomes darker.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 48 Monday, July 31, 2006 3:12 PM

Conﬁguring the DVD player—Continued

■ Subwoofer

Audio Menu

On (default): Select if a subwoofer is connected.

Off: Select if no subwoofer is connected.

Digital/HDMI Audio Out

With this setting you can conﬁgure the optical, coaxial,

and HDMI digital outputs.

■ Front Speaker

Large: Select if the front speakers are large.

All (default): Dolby Digital and DTS signals are out-

put as they are.

Small (default): Select if the front speakers are

small.

PCM: Dolby Digital and DTS signals are down

mixed to 2 channels and output as PCM.

Note:

• If the Subwoofer setting is set to Off, this setting is

ﬁxed at Large and cannot be changed.

Off: No digital signals are output.

Note:

■ Center Speaker

• MPEG is output as PCM regardless of this setting.

Large: Select if the center speaker is large.

Small (default): Select if the center speaker is small.

Off: Select if no center speaker is connected.

Linear PCM Out

With this setting you can conﬁgure the DVD player to

output digital audio with higher sampling rates (e.g.,

88.2 kHz, 96 kHz) as it is or to down sample it to 48 kHz

or below.

If the AV component you connect to the DVD player’s

digital audio outputs supports 96 kHz digital audio,

select Down Sample Off. Otherwise, select Down Sam-

ple On.

Note:

• If the Front Speaker setting is set to Small, the

Large option cannot be selected.

■ Surround Speaker

Large: Select if the surround speakers are large.

Small (default): Select if the surround speakers are

small.

Down Sample On: 196 kHz and 96 kHz sources are

down sampled to 48 kHz, and 176.4 kHz and

88.2 kHz sources are down sampled to 44.1 kHz.

Off: Select if no surround speakers are connected.

Note:

Down Sample Off (default): Sources are output as

they are.

• If the Front Speaker setting is set to Small, the

Large option cannot be selected.

Notes:

• Some copy-protected DVD-Video discs may use

96 kHz digital audio only for D/A conversion to the

analog audio outputs.

Test Tone

If you can adjust the volume level of each channel of

your amp’s multichannel input, with this function, you

can output a test tone from each multichannel output

jack in turn and adjust each level as necessary.

1. Use the Up/Down [ ]/[ ] buttons to select a

speaker, and then press the [Enter] button.

• With some discs, even if you select Down Sample Off,

the digital audio will be down sampled, and in some

cases may not be output by the DVD player’s digital

audio outputs.

A test tone is output by each speaker as it’s selected.

Speaker Conﬁguration

2. Refer to your AV receiver’s instruction manual

for details on adjusting the volume level of each

channel.

With these settings, you can specify which speakers are

connected and their sizes. These settings only apply to

the DVD player’s analog multichannel output. If you

connect to only the FRONT/D.MIX L/R jacks, set the

Subwoofer, Center Speaker, and Surround Speaker set-

tings to Off.

Note:

• The test tone is not output by the digital audio outputs.

Note:

• The Speaker Conﬁgurations have no effect on

192 kHz/176.4 kHz DVD-Audio.

• To use the Speaker Conﬁguration settings with SACD

playback, in the SACD Audio Setup, select PCM.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 49 Monday, July 31, 2006 3:12 PM

Conﬁguring the DVD player—Continued

Center Delay and Surr. Delay

Dynamic Range Control (Dolby Digital

only)

With these settings, you can adjust the multichannel out-

put signals relative to the listening position.

With the Dynamic Range Control function you can

reduce the dynamic range of Dolby Digital material so

that you can still hear quiet parts even when listening at

low volume levels—ideal for watching movies late at

night when you don’t want to disturb anyone.

For 5.1-channel surround playback, ideally your speak-

ers should all be the same distance away from the listen-

ing position, but this isn’t always practical. By setting a

delay time for the center and surround speakers, you can

adjust their virtual positions without having to physically

move them, creating the ideal listening environment. The

diagram below shows the ideal locations for the center

and surround speakers.

Off (default): The full dynamic range is preserved.

On: The dynamic range of Dolby Digital material is

compressed.

Notes:

Ideal location of center speaker

• The impact of the Dynamic Range Control function

depends on the Dolby Digital material that you are

playing and with some material there will be little or

no effect.

• When the DVD player is set to Standby, this function

is automatically set to Off.

(A)

All speakers should be

locatedwithinthecircle

with a radius of Df.

• Depending on the Speaker Conﬁguration settings, this

setting may be ﬁxed.

(B)

Ideal location of a

surround speaker

Dolby Pro Logic Setting

This setting determines how the DVD player’s built-in

Dolby Pro Logic decoder works with 2-channel material.

■ Center Delay

Center Delay (A) = Df – Dc

On: The Dolby Pro Logic decoder decodes Dolby

Surround material and processes the following audio

formats: 2-channel Dolby Digital on DVD-Video

discs, 48 kHz (16-, 20-, and 24-bit) PCM audio on

DVD-Video discs, and 2-channel audio on CDs.

No Delay (default): When Df equals Dc.

1msec: When (A) is approx. 1 ft. (0.3 m)

2msec: When (A) is approx. 2 ft. (0.6 m)

3msec: When (A) is approx. 3 ft. (0.9 m)

4msec: When (A) is approx. 4 ft. (1.2 m)

5msec: When (A) is approx. 5 ft. (1.5 m)

Off (default): The Dolby Pro Logic decoder is off.

Note:

• If the Center Speaker or Surround Speaker is set to Off

in the Speaker Conﬁguration settings (page 48), the

Dolby Pro Logic decoder will not work even if you

select Auto or On.

■ Surr. Delay

Surr. Delay (B) = Df – Ds

No Delay (default): When Df equals Ds.

5msec: When (B) is approx. 5 ft. (1.5 m)

10msec: When (B) is approx. 10 ft. (3 m)

15msec: When (B) is approx. 15 ft. (4.5 m)

20msec: When (B) is approx. 20 ft. (6 m)

25msec: When (B) is approx. 25 ft. (7.5 m)

SACD Audio Setup

With this setting you can choose whether DSD (Direct

Stream Digital) or PCM is output when playing Super

Audio CDs.

When DSD is selected, the Speaker Conﬁguration set-

tings have no effect and the source is output as it is: 2-

channel material is output as 2-channels, and multichan-

nel material is output as multichannel.

When PCM is selected, the source is output is in accor-

dance with the Speaker Conﬁguration settings and the

output is down mixed.

Notes:

• The delay settings have no effect on 192 kHz/

176.4 kHz DVD-Audio.

• To use the delay settings with SACD playback, in the

SACD Audio Setup, select PCM.

DSD (default): The source signal is output as it is.

PCM: The source signal is output in accordance with

the Speaker Conﬁguration settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 50 Monday, July 31, 2006 3:12 PM

Conﬁguring the DVD player—Continued

Downmix Setting

Audio

With this setting you can conﬁgure the FRONT/D.MIX

AUDIO OUT jacks and AV CONNECTOR for use with

a 2-channel stereo amp or an amp with a built-in Dolby

Pro Logic decoder. It determines how multichannel

audio sources are down mixed.

With this setting you can select your preferred language

for soundtracks. When you play a DVD-Video disc with

multiple language soundtracks, your preferred language

will be selected automatically.

Select “Others” if the language you want is not dis-

played. See “Selecting Other Languages” on page 51.

In the Speaker Conﬁguration, set the Subwoofer, Center

Speaker, and Surround Speaker settings to Off.

Notes:

• Not all DVD-Video discs have soundtracks in multiple

languages.

Stereo (default): Choose this option if you’re con-

necting the FRONT/D.MIX AUDIO OUT jacks or

AV CONNECTOR to a stereo amp or TV. Multi-

channel audio is down mixed into stereo.

• Even if a DVD-Video disc has soundtracks in multiple

languages, this setting may not always work.

• If a DVD has only one soundtrack, that will be used.

• With some DVD-Video discs you can select languages

from a menu.

Lt/Rt: Choose this option if you’re connecting the

FRONT/D.MIX AUDIO OUT jacks or AV CON-

NECTOR to an AV receiver, TV, or other component

with a built-in Dolby Pro Logic decoder. Multichan-

nel audio is down mixed into an Lt/Rt mix, which is

a 2-channel mix containing front left, front right,

center, and surround channel information.

Subtitle Language

With this setting you can select your preferred language

for subtitles. When you play a DVD-Video disc with

multiple language subtitles, your preferred language will

be selected automatically.

Select “No Subtitle” if you don’t want subtitles dis-

played. Select “Others” if the language you want is not

displayed. See “Selecting Other Languages” on page 51.

Language Menu

On-Screen Language

With this setting you can select a language for the

onscreen setup menus and messages.

Notes:

• Not all DVD-Video discs have subtitles.

• Even if a DVD-Video disc has subtitles in multiple

languages, this setting may not always work.

• If a DVD has only one subtitle language, that will be

used.

Select one of the displayed languages.

Disc Menu Language

With this setting you can select your preferred language

for disc menus. When you play a DVD-Video disc with

multiple language disc menus, your preferred language

will be selected automatically.

• With some DVD-Video discs you can select subtitles

from a menu.

Select “Others” if the language you want is not dis-

played. See “Selecting Other Languages” on page 51.

Notes:

• Not all DVD-Video discs have menus in multiple lan-

guages.

• Even if a DVD-Video disc has menus in multiple lan-

guages, this setting may not always work.

• If a DVD has only one menu language, that will be

used.

• With some DVD-Video discs you can select languages

from a menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 51 Monday, July 31, 2006 3:12 PM

Conﬁguring the DVD player—Continued

■ Selecting Other Languages

This section explains how to select other languages for

disc menus, audio, and subtitles.

Language

Byelorussian

Bulgarian

Bihari

Code

Language

Panjabi

Code

Polish

Pashto, Pushto

Quechua

Rhaeto-Romance

Kirundi

Select “Others” from the Disc

Bislama

Bengali

Remote

controller

Menu Language, Audio Lan-

guage, or Subtitle menu, and

then press [Enter].

Tibetan

Breton

Romanian

Kinyarwanda

Sanskrit

Sindhi

Catalan

Corsican

Czech

Use the remote controller’s Left/

Right [ ]/[ ] buttons to select the

code.

Use the Up/Down [ ]/[ ] buttons

to enter a language code.

See adjacent table for language codes.

Welsh

Sangho

Serbo-Croatian

Sinhalese

Slovak

Danish

Remote

controller

Bhutani

Esperanto

Estonian

Basque

Persian

Slovenian

Samoan

Shona

Finnish

Somali

Fiji

Albanian

Serbian

Siswati

Faroese

Frisian

When you’ve ﬁnished, press the

[Enter] button.

Remote

controller

Irish

Sesotho

Sundanese

Swahili

Scots-Gaelic

Galician

Guarani

Gujarati

Hausa

Tamil

Telugu

Tajik

Hindi

Thai

Croatian

Hungarian

Armenian

Interlingua

Interlingue

Inupiak

Tigrinya

Turkmen

Tagalog

Setswana

Tonga

Use this list when specifying other languages.

Language

Japanese

English

Code

Language

Kirghiz

Code

Latin

Turkish

French

Lingala

Indonesian

Icelandic

Hebrew

Yiddish

Tsonga

Tatar

German

Italian

Laothian

Lithuanian

Latvian

Twi

Spanish

Chinese

Dutch

Ukrainian

Urdu

Malagasy

Maori

Javanese

Georgian

Kazakh

Uzbek

Portuguese

Swedish

Russian

Korean

Macedonian

Malayalam

Mongolian

Moldavian

Marathi

Malay

Vietnamese

Volapük

Wolof

Greenlandic

Cambodian

Kannada

Kashmiri

Kurdish

Xhosa

Greek

Yoruba

Afar

Zulu

Abkhazian

Afrikaans

Amharic

Arabic

Maltese

Burmese

Nauru

Nepali

Assamese

Aymara

Azerbaijani

Bashkir

Norwegian

Occitan

Oromo

Oriya

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 52 Monday, July 31, 2006 3:12 PM

Conﬁguring the DVD player—Continued

DivX Subtitle (Not North American model)

Display Menu

Some DivX video discs include subtitles in one or more

languages. The disc packaging will usually inform you

about which subtitle languages are available.

With this setting you can select your preferred language

for DivX subtitles. When you play a DivX disc with mul-

tiple language subtitles, your preferred language will be

selected automatically.

On-Screen Display

With this setting you can turn on or off onscreen mes-

sages, such as “Play,” “Stop,” and “Resume.”

Off: Onscreen messages are not displayed.

On (default): Onscreen messages are displayed.

You can select DivX subtitle languages by region:

On-Screen Display Color

Unicode (UTF-8): Unicode encoding scheme. Two

With this setting you can set the color and theme of the

Disc navigation window.

bytes are used to encode each character.

Western European: Albania, Breton, Catalan, Dan-

ish, Dutch, English, Faroese, Finnish, French,

Gaelic, German, Icelandic, Irish, Italian, Norwegian,

Portuguese, Spanish, and Swedish

Sapphire

Pearl

Amethyst

Garnet

Standard: Albanian, Danish, Dutch, English, Finn-

ish, French, Gaelic, German, Italian, Kurdish

(Latin,) Norwegian, Portuguese, Spanish, Swedish,

and Turkish

Background

With this setting you can select the color of the back-

ground that’s displayed when the DVD player is stopped.

Central European: Albanian, Croat, Czech, Dutch,

English, German, Hungarian, Irish, Polish, Roma-

nian, Slovak, Slovene, and Serbian

Blue

Gray

Cyrillic: Bulgarian, Byelorussian, English, Mace-

donian, Moldavian, Russian, Serbian, and Ukrainian

Graphic: The theme picture speciﬁed for the On-

Screen Display Color setting is used.

Greek: English and Modern Greek

Hebrew: English and Modern Hebrew

Arabic: Arabic

Screen Saver

With the Screen Saver function you can protect your TV

against screen burn-in, which can occur when the same

image or menu is displayed for a long time.

Baltic: Baltic

Vietnam: Vietnamese

Chinese: Chinese

Off: Screen saver off.

On (default): Screen saver on.

Korean: Korean

When the Screen Saver function is set to On, and play-

back is stopped for 15 minutes, the Screen Saver func-

tion automatically displays a moving image.

Once the screen saver has been activated, you can cancel

it by pressing either the Play [ ] button.

Notes:

• Some external subtitle ﬁles may display incorrectly or

not at all.

• Supported ﬁle types for external subtitle ﬁles:

.srt, .sub, .txt, .smi, .ssa, .ass, .psb.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 53 Monday, July 31, 2006 3:12 PM

Conﬁguring the DVD player—Continued

Change the Security Code

Operation Setting Menu

To change the Security Code, conﬁrm your existing code

then enter a new one.

Setting the Parental Lock

With the Parental Lock function you can block access to

certain scenes that the authors have ﬂagged as being

unsuitable for children.

Select “Operation Setting” menu

in the setup.

Use the Up/Down [ ]/[ ] buttons

to select “Security Code,” and

then press the [Enter] button.

Select “Operation Setting” menu

Remote

controller

in the setup.

The security code input screen appears.

Use the Up/Down [ ]/[ ] buttons

to select “Parental Lock,” and

then press the [Enter] button.

Remote

controller

The security code input screen appears.

Enter the existing security code

using the remote controller’s

Remote

controller

number buttons, and then press

the [Enter] button.

Enter the security code using the

remote controller’s number but-

tons, and then press the [Enter]

button.

The default security code is “8888.”

You can change the security code in the

next section.

The default security code is “8888.”

Even if a new security code has been

entered, the code “8888” can still be

used.

Once the security code has been

entered, the new security code input

screen appears.

Remote

controller

Enter the new security code

using the remote controller’s

Remote

controller

number buttons, and then press

the [Enter] button.

The new security code has been set.

Use the Up/Down [ ]/[ ] buttons

to change the level of parental

Remote

lock, and then press the [Enter]

controller

button.

At level 8 parental lock is off, with level

1 being the strictest level.

Notes:

• When entering a security code, you can use the [CLR]

button to delete the numbers entered so far, if neces-

sary.

• Not all discs use parental lock. See the disc’s sleeve

notes for details.

• Discs with parental lock may cut certain scenes,

replace certain scenes with children-friendly scenes,

or prevent playback of the entire disc.

Note:

• If you forget your security code, enter “8888” instead.

“8888” is a security code that can always be used.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 54 Monday, July 31, 2006 3:12 PM

Conﬁguring the DVD player—Continued

DVD Priority Contents

DivX Registration

DVD-A

To play DivX VOD (video on demand) content on this

DVD player, you ﬁrst need to register it with your DivX

VOD content provider.You do this by generating a DivX

VOD registration code, which you then submit to your

provider.

This setting determines what is played when a

DVD-Audio disc also contains DVD-Video material.

DVD-AUDIO (default): The DVD-Audio material is

played.

Your 8-digit registration code is displayed.

DVD-VIDEO: The DVD-Video material is played.

SACD Priority Contents

DivX® Video On Demand

Your registration code is:

SACD

01234567

(http://www.divx.com/vod)

SACDs have two separate areas for storing audio

tracks—one for multichannel audio, the other for 2-

channel stereo audio. In addition, hybrid SACDs have

an extra layer for playback in standard CD players.

With this setting you can determine how SACDs are

played by the DVD player.

Make a note of the code as you will need it when you

Important:

• DivX VOD content is protected by DRM (digital

rights management). This restricts playback of content

to speciﬁc, registered devices.

• Resetting the DVD player (as described at the end of

this manual) will not cause you to lose your registra-

tion code.

2 ch Area: The 2-channel stereo audio tracks are

played.

Multi ch Area (default): The multichannel audio

tracks are played.

CD Area: The CD layer of hybrid SACDs is played.

Notes:

• This setting determines which area of the disc is

played initially. If Multi ch Area is selected, and an

SACD that contains no multichannel area is loaded,

the 2-channel area will be played.

Auto power off

The Auto power off function automatically turns off the

DVD player after 20 minutes of inactivity.

Off (default): Auto power off function off.

On: Auto power off function on.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 55 Monday, July 31, 2006 3:12 PM

Additional information

Resetting the player

Disc Content Organization

Use this procedure to reset all the player’s settings to the

factory default.

■ DVD-Video Format

DVD-Video discs contain titles, which are usually subdi-

vided into chapters.

Turn on the DVD player.

Title 2

Title 1

Wait until “INTEGRA” has disappeared

from the display.

Chapter 1

Chapter 2

Chapter 1

Chapter 2

Using the front panel buttons,hold

down the Stop [ ] button and

press [Standby/On] button.

“INITIALIZE” appears on the display.

When the reset is complete, “COM-

PLETE” is displayed, and the DVD

player enters Standby mode.

DVD-Video

■ DVD-Audio

DVD-Audio discs contain groups and tracks.

Group 1

Track 2

Group 2

Track 1 Track 2

Track 1

Track 3

DVD-Audio

■ SACD

SACDs have two separate areas for storing audio

tracks—one for multichannel audio, the other for 2-

channel stereo audio. In addition, hybrid SACDs have an

extra layer for playback in standard CD players.You can

specify how the DVD player handles SACDs on page 49.

Adjusting the Display Brightness

You can adjust the brightness of the display as follows.

Press the [Dimmer] button

repeatedly to cycle through the

following options:

Multichannel area

Track 1 Track 2 Track 3

Stereo area

Track 2

Track 1

Track 3

dim, dimmer, normal.

CD layer of a hybrid SACD

SACD

DVD-Video regions

■ VCD

VCDs contain video tracks.

All DVD-Video discs carry a region mark on the case

somewhere that indicates which region(s) of the world

the disc is compatible with. Your DVD player also has a

region mark, which you can ﬁnd on the rear panel. Discs

from incompatible regions will not play in this player.

Discs marked “ALL” will play in any player.

The diagram below shows the various DVD regions of

the world.

Track 1

Track 2

Track 3

Track 4

Video CD

■ DVD-VR

DVD-VR discs contain programs, which may be subdi-

vided into cells. They may also contain playlists.

Program 2

Program 1

Cell 1

Cell 2

Cell 1

Cell 2

DVD-VR

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 56 Monday, July 31, 2006 3:12 PM

Additional information—Continued

■ Audio CD Format

■ MP3, WMA & JPEG Files

Audio CDs contain tracks.

MP3, WMA, and JPEG ﬁles are typically organized into

folders. The DVD player handles MP3, WMA, and

JPEG ﬁles as tracks.

Track 1

Track 2

Track 3

Track 4

Track 5

Folder 1

Track 2

Folder 2

Track 1 Track 2

Audio CD

Track 1

Track 3

MP3/WMA/JPEG (CD-R/CD-RW)

Glossary

Analog audio

DRM

An electrical signal that directly represents sound. Com-

pare this to digital audio which can be an electrical sig-

nal, but is an indirect representation of sound. See also

“Digital audio.”

DRM (digital rights management) is a type of server

software developed to enable secure distribution of paid

content over the web, recently incorporated by WMA

(Windows Media Audio).

Aspect ratio

DTS

The width of a TV screen relative to its height. Conven-

tional TVs are 4:3 (in other words, the screen is almost

square); widescreen models are 16:9 (the screen is

almost twice as wide as it is high).

DTS stands for Digital Theater Systems. DTS is

a surround system different from Dolby Digital that has

become a popular surround sound format for movies.

Dynamic range

Digital audio

The difference between the quietest and loudest sounds

possible in an audio signal (without distorting or getting

lost in noise).

Dolby Digital and DTS soundtracks are capable of a very

wide dynamic range, delivering dramatic cinema-like

effects.

An indirect representation of sound by numbers. During

recording, the sound is measured at discrete intervals

(44,100 times a second for CD audio) by an analog-to-

digital converter, generating a stream of numbers.

On playback, a digital-to-analog converter generates an

analog signal based on these numbers. See also “Sam-

pling frequency” and “Analog audio.”

File extension

A tag added to the end of a ﬁlename to indicate the type

of ﬁle. For example, “.mp3” indicates an MP3 ﬁle.

DivX

DivX is a media technology created by DivX,

Inc. DivX media ﬁles contain compressed video. DivX

ﬁles can also include advanced media features like

menus, subtitles, and alternate audio tracks.

Abbreviation for high deﬁnition, as in HDTV (high-def-

inition TV).

HDCP (High-bandwidth Digital Content Protection)

The video encryption technology developed by Intel for

HDMI/DVI. It’s designed to protect video content and

requires a HDCP-compatible device to display the

encrypted video.

Dolby Digital

Using a maximum of 5.1 channels of audio,

this high quality surround system is used in many of the

ﬁner movie theaters around the world.

The on-screen display shows which channels are active,

for example showing 3/2.1. The 3 being the two front

channels and the center channel; the 2 being the surround

channels, and the .1 being the LFE channel.

*1. DivX, DivX Certiﬁed, and associated logos are trademarks of

DivX, Inc. and are used under license.

*2. Manufactured under license from Dolby Laboratories. “Dolby”

and the double-D symbol are trademarks of Dolby Laborato-

ries.

*3. “DTS” and “DTS Digital Out” are registered trademarks of

Digital Theater Systems, Inc.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 57 Monday, July 31, 2006 3:12 PM

Glossary—Continued

Regions (DVD-Video only)

HDMI

These associate discs and players with particular areas of

the world. This unit will only play discs that have com-

patible region codes. You can ﬁnd the region code of

your unit by looking on the rear panel. Some discs are

compatible with more than one region (or all regions).

HDMI (High-Deﬁnition Multimedia Interface) is a high-

speed digital interface which has the capability to sup-

port standard, enhanced, or high-deﬁnition video plus

standard to multichannel surround-sound audio on a sin-

gle digital connection. HDMI features include uncom-

pressed digital video, a bandwidth of up to 5 gigabytes

per second and communication between the AV source

and AV devices such as DTVs.

Sampling frequency

The rate at which sound is measured to be turned into

digital audio data. The higher the rate, the better the

sound quality, but the more digital information is gener-

ated. Standard CD audio has a sampling frequency of

44.1kHz, which means 44,100 samples (measurements)

per second. See also “Digital audio.”

ISO 9660 format

International standard for the volume and ﬁle structure

of CD-ROM discs.

JPEG

WMA

A ﬁle format used for still images, such as photographs

and illustrations. JPEG ﬁles are identiﬁed by the ﬁle

extension “.jpg” or “.JPG”. Most digital cameras use this

format.

WMA is short for Windows Media Audio and refers to

an audio compression technology developed by

Microsoft Corporation. WMA data can be encoded by

using Windows Media Player version 8.

MP3

MP3 (MPEG1 audio layer 3) is a compressed audio ﬁle

format. Files are recognized by their ﬁle extension

“.mp3” or “.MP3”.

MPEG video

The video format used for Video CDs and DVDs. Video

CD uses the older MPEG-1 standard, while DVD uses

the newer and much better quality MPEG-2 standard.

PBC (PlayBack Control) (Video CD only)

A system of navigating a Video CD through on-screen

menus recorded onto the disc. Especially good for discs

that you would normally not watch from beginning to

end all at once—karaoke discs, for example.

PCM (Pulse Code Modulation)

The most common system of encoding digital audio,

found on CDs and DAT. Excellent quality, but requires a

lot of data compared to formats such as Dolby Digital.

For compatibility with digital audio recorders (CD, MD,

and DAT) andAV ampliﬁers with digital inputs, this unit

can convert Dolby Digital, and DTS to PCM. See also

“Digital audio.”

Progressive scan video

All the lines that make up a video picture are updated in

one pass (compared to interlace which takes two passes

to update the whole picture).

*1. HDMI, the HDMI logo and High-Deﬁnition Multimedia Inter-

face are trademarks or registered trademarks of HDMI licens-

ing LLC.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 58 Monday, July 31, 2006 3:12 PM

Troubleshooting

Symptom

Possible cause

Remedy

Connect the power cord to a suitable wall outlet

(page 26).

The power cord is not connected.

Can’t turn on the DVD

player?

Turn off the DVD player, wait ﬁve seconds, then try

turning it on again. If that fails, disconnect the

power cord from the wall outlet, wait ﬁve seconds,

reconnect it, then try turning it on again.

External interference is affecting the DVD

player’s digital circuitry.

The DVD player turns

itself off when it’s not

being used?

TheAuto power off function will turn the DVD

player off automatically after 20 minutes of

inactivity.

TheAuto power off function can be turned on or off

as required (page 54).

On your TV, select the input to which the DVD

player is connected.

The wrong input source is selected on your TV.

The video cable is not connected properly.

Check the video cable and correct as necessary.

The PAL Output Setting is set wrong for your Change the PAL Output Setting to suit your TV

TV.

(page 47).

No HDMI Video Output?

The HDMI Output Setting is set to Off.

Try pressing the [HDMI] button on the front panel

repeatedly to switch the HDMI OUT on, and then

pressing the [Resolution] button repeatedly to get

picture (page 43).

Your TV doesn’t support HDMI Resolution

settings of 720p and 1080i.

If the DVD player is connected to yourAV receiver,

try connecting it directly to your TV. It will not

work if you connect to a component that doesn’t

support HDCP (page 24).

The connected component doesn’t support

HDCP.

No picture?

No Component Video Output?

Your TV does not support progressive scan-

ning, and the HDMI OUT is on.

While the HDMI OUT is on, the component

video output outputs progressive video.

Try pressing the [HDMI] button on the front panel

repeatedly to switch the HDMI OUT off, and then

pressing the [Resolution] button repeatedly to

switch to Interlaced (page 43).

The HDMI Resolution is not set to 480p

(480p/576p).

Press the [Resolution] button repeatedly to select

480p (480p/576p) (page 43).

No S-Video or Composite Video Output?

The HDMI Resolution is not set to 480p

(480p/576p).

Try pressing the [Resolution] button on the front

panel repeatedly to get picture (page 19).

The wrong input source is selected on your

hi-ﬁ amp or AV receiver.

On your hi-ﬁ amp orAV receiver, select the input to

which the DVD player is connected.

The audio cable is not connected properly.

Your hi-ﬁ amp or AV receiver is turned off.

Check the audio cable and correct as necessary.

Turn on your hi-ﬁ amp or AV receiver.

No sound?

Not all of the analog and digital audio outputs See page 19 for details on how the DVD player out-

work with all disc types and formats. puts audio from each output.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 59 Monday, July 31, 2006 3:12 PM

Troubleshooting—Continued

Symptom

Possible cause

Remedy

No Sound from the HDMI OUT?

The Digital/HDMI Audio Out setting is set to Change the Digital/HDMI Audio Out setting to

Off. either All or PCM (page 48).

The DVD player is connected to the DVI jack You won’t hear any sound from the HDMI OUT if

on your TV or AV receiver. your TV or AV receiver only supports DVI.

The HDMI setting on your TV or AV receiver Change the HDMI setting on your TV or AV

is set to DVI. receiver to HDMI.

Your TV orAV receiver doesn’t support Dolby Change the Digital/HDMI Audio Out setting to

or DTS.

PCM (page 48).

SACD audio is not output by the HDMI OUT

(page 19).

You’re playing an SACD.

No sound?

Your TV or AV receiver doesn’t support

88.2 kHz, 96 kHz, 176.4 kHz or 196 kHz

PCM.

Change the Linear PCM Out setting to Down Sam-

ple On (page 48).

No Digital Audio Output?

The Digital/HDMI Audio Out setting is set to Change the Digital/HDMI Audio Out setting to

Off. either All or PCM (page 48).

Your TV orAV receiver doesn’t support Dolby Change the Digital/HDMI Audio Out setting to

or DTS.

PCM (page 48).

Your TV or AV receiver doesn’t support

88.2 kHz, 96 kHz, 176.4 kHz or 196 kHz

PCM.

Change the Linear PCM Out setting to Down Sam-

ple On (page 48).

The disc is dirty.

Remove the disc and clean it (page 11).

The picture distorts occa-

sionally?

You’re using the Fast Forward or Fast Reverse A little picture distortion may occur when using

function.

these functions. This is normal.

The DVD player is connected to your TV via a

VCR or other video equipment whose copy

protection system is affecting the picture.

Picture instability or

noise?

Connect the DVD player directly to your TV

(page 20).

No disc loaded.

Load a disc (page 28).

The disc is incompatible.

The disc is upside down.

Load only compatible discs (pages 9, 10).

Load the disc the correct way up (page 28).

Place the disc in the center of the disc tray

(page 28).

Can’t start playback?

The disc is not centered in the disc tray.

The disc is dirty.

Remove the disc and clean it (page 11).

The disc supports parental lock and the Paren-

tal Lock function is on.

Turn off the Parental Lock function (page 53).

Can’t watch the

DVD-Video material on a

DVD-Audio disc?

The DVD Priority Contents setting is set to

DVD-AUDIO.

Set the DVD Priority Contents setting to

DVD-VIDEO (page 54).

Can’t play the multichan-

nel area of a hybrid

SACD?

The SACD Priority Contents setting is not set Set the SACD Priority Contents setting to Multi ch

to Multi ch Area.

Area (page 54).

The disc is not ISO 9660 Level 2 format.

The disc has not been ﬁnalized.

Use only ISO 9660 Level 2 format discs (page 10).

Finalize the disc (page 10).

Can’t play MP3 and JPEG

discs?

There’s a noise when using During CD 1-Track Repeat playback, the start

repeat playback. of the next track may be heard.

This is not a malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 60 Monday, July 31, 2006 3:12 PM

Troubleshooting—Continued

Symptom

Possible cause

Remedy

MP3 ﬁles without a “.mp3” or “.MP3” ﬁle-

name extension are not recognized.

Use the correct ﬁlename extension (page 10).

Can’t select MP3 ﬁles?

Only ﬁles in the ﬁrst session of a multisession disc

can be played (page 10).

The MP3 disc is a multisession disc.

WMA ﬁles without a “.wma” or “.WMA” ﬁle-

name extension are not recognized.

Use the correct ﬁlename extension (page 10).

Don’t use the copyright option (page 10).

Can’t play WMA ﬁles?

Can’t view JPEG ﬁles?

The WMA ﬁle’s copyright option is on.

JPEG ﬁles without a “.jpg” or “.JPG” or

“.JPEG” ﬁlename extension are not recog-

nized.

Use the correct ﬁlename extension (page 10).

Use JPEG ﬁles that are less than 5 megabytes

(page 10).

The JPEG ﬁle is too big.

Turn off the DVD player, wait ﬁve seconds, then

turn it on again. If that doesn’t resolve the issue,

disconnect the power cord from the wall outlet,

wait ﬁve seconds, reconnect it, then try again.

Buttons on the DVD player Power supply voltage ﬂuctuations and other

and remote controller

don’t work?

anomalies, such as static electricity, can inter-

fere with normal operation.

There are no batteries in the remote controller. Install new batteries (page 12).

The batteries are ﬂat.

Replace with new batteries (page 12).

Check the batteries and correct as necessary

(page 12).

The batteries are installed incorrectly.

You’re not pointing the remote controller at the Point the remote controller at the DVD player’s

DVD player’s remote sensor.

remote sensor (page 12).

Buttons on the DVD player

work OK but those on the

remote controller don’t?

Use the remote controller closer to the DVD player

(page 12). The remote controller has a range of

approximately 16 ft. (5 meters).

You’re too far away from the DVD player.

Make sure that the DVD player is not subjected to

direct sunshine or inverter-type ﬂuorescent lights.

Relocate if necessary.

A strong light source is interfering with the

DVD player’s remote sensor.

If the DVD player is installed in a cabinet with

colored glass doors, the remote controller may

not work reliably when the doors are closed.

Open the doors, or use a cabinet without colored

glass.

The DVD player contains a microcomputer for signal processing and control functions. In very rare situa-

tions, severe interference, noise from an external source, or static electricity may cause it to lockup. In the

unlikely even that this should happen, unplug the power cord from the wall outlet, wait at least ﬁve seconds,

and then plug it back in again. Alternatively, press and hold the Stop [ ] button until “RESET” appears on

the display (about 10 seconds).

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the

unit’s malfunction. Before you record important data, make sure that the material will be recorded correctly.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 61 Monday, July 31, 2006 3:12 PM

Troubleshooting—Continued

■ HDMI Status Mode

If you’re using an HDMI connection and there’s no picture or sound, you can check the status of the HDMI connection

by pressing and holding down the DVD player’s [Display] button for 10 seconds until a message ID appears on the

display. Look up the message ID in the following tables and check the HDMI connections and settings on both the DVD

player and the connected component.

HDMI connection and HDMI-related settings status

Displayed ID

Message

Turn the DVD player and the connected component off, then turn them on again. Make sure that

the connected component is working properly and that the DVD player’s HDMI settings are conﬁg-

ured suitably for that component.

MSG ID 001

MSG ID 015

No picture from the HDMI connection

Displayed ID

Message

MSG ID 002

The HDMI Output Setting is set to Off. Change it to On (page 43).

MSG ID 003

MSG ID 004

The HDMI cable may not be connected properly. Check the connection. Also, make sure the HDMI

input on the TV or AV receiver is correctly conﬁgured to received HDMI.

Make sure the HDMI input on the TV or AV receiver is correctly conﬁgured to received HDMI.

The connected component may not support HDCP. Make sure the connected component supports

HDCP.

Turn the DVD player and the connected component off, then turn them on again.

The DVD player may be connected to the other component’s DVI jack. Some TVs may not properly

receive the video output by the DVD player. Also, with a DVI connection, there will be no sound.

MSG ID 005

MSG ID 006

MSG ID 007

The DVD player’s HD Resolution setting is set to 720p or 1080i. If your TV doesn’t support these

resolutions, select another resolution (page 43).

MSG ID 008

MSG ID 009

The connected component may not be receiving the HDMI signal properly.

Try selecting another resolution on the DVD player (page 43).

No sound from the HDMI connection

Displayed ID

Message

The DVD player’s Digital/HDMI Audio Out setting is set to Off. Change the setting to All or PCM

(page 48).

MSG ID 010

MSG ID 011

MSG ID 014

The connected component may not support 96 kHz PCM. Set the DVD player’s Linear PCM Out

setting to Down Sample On (page 48).

MSG ID 012

MSG ID 013

The connected component may not support Dolby Digital. Set the DVD player’s Digital/HDMI Audio

Out setting to PCM (page 48).

MSG ID 016

MSG ID 017

The connected component may not support DTS. Set the DVD player’s Digital/HDMI Audio Out

setting to PCM (page 48).

MSG ID 020

Audio from SACDs is not output by the HDMI OUT (page 19).

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 62 Monday, July 31, 2006 3:12 PM

Speciﬁcations

North American model: NTSC

Other model: PAL/NTSC

Signal System

Composite Video Output/Impedance

S-Video Output/Impedance

1.0 V (p-p)/75Ω negative sync, RCA

Y: 1.0 V (p-p)/75Ω negative sync, 4-pin mini DIN

C: 0.286 V (p-p)/75Ω

Y: 1.0 V (p-p)/75Ω

PB/PR: 0.7 V (p-p)/75 Ω RCA/ phono

Component Video Output/Impedance

Component Video Frequency Response

DVD Audio

5 Hz–50 MHz

4 Hz–88 kHz (192 kHz)

4 Hz–50 kHz

Super Audio CD

Frequency response

4 Hz–44 kHz (96 kHz)

4 Hz–22 kHz (48 kHz)

DVD Linear Sound

Audio CD

4 Hz–20 kHz (44.1 kHz)

106 dB

S/N Ratio

Audio Dynamic Range

96 dB

THD (Total Harmonic Distortion)

Wow and Flutter

0.003% (1 kHz)

Below threshold of measurability

–22.5 dBm

Audio Output (Digital/Optical)

Audio Output/Impedance (Digital/Coaxial)

0.5 p-p/75Ω

FRONT D.MIX/CENTER/SUBWOOFER: 2.0 V/440Ω

SURROUND 1, 2: 2.0 V/440Ω (SURR MODE 1)

1.4 V/440Ω (SURR MODE 1+2)

Audio Output/Impedance (Analog)

■ General

North American model: AC 120 V, 60 Hz

Other model: AC 100–240 V, 50/60 Hz

Power Supply

Power Consumption

17 W

Stand-by Power Consumption

0.4 W

435 x 81 x 312 mm

(17 1/8 x 3 3/16 x 12 5/16 ins.)

Dimensions (W x H x D)

Weight

3.7 kg (8.2 lbs.)

Operation Condition Temperature and Humidity

5˚C–35˚C (41˚F–95˚F), 5%–85%

SACD, DVD-Audio, DVD-video, DVD-R/RW (VR, VIDEO),

DVD+R/RW, CD, CD-R/RW, Video CD, MP3, WMA, JPEG,

DivX (not North American model)

Disc Compatibility

Disc that have not been property ﬁnalized may only be partially

playable or not playable at all

Speciﬁcations and features subject to change without notice.

The letter displayed at the end of the product name found in catalogs and on package represents the color of the DVD

player. Though the color varies, the speciﬁcations and operations are the same.

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 63 Monday, July 31, 2006 3:12 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

DPS-6.7_En.book Page 64 Monday, July 31, 2006 3:12 PM

Integra Division of

ONKYO U.S.A. CORPORATION

18 park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com

Integra Division of

ONKYO CORPORATION

Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8124

I0608-1

SN 29344215

* 2 9 3 4 4 2 1 5 *

Download from Www.Somanuals.com. All Manuals Search And Download.

Indesit Washer IWB6065 User Manual
Ingersoll Rand Paint Sprayer 210CSA User Manual
Intel Life Jacket SC450NX User Manual
JBL Portable Speaker S412PII User Manual
Jenoptik Digital Camera 50z3 User Manual
JVC Network Router PD 42DX User Manual
Kensington Computer Keyboard K62064A MSRP User Manual
Kenwood Speaker KFC 1362 User Manual
Kenwood Two Way Radio TKR 751 User Manual
King Canada Sander KC 6108 OSC User Manual