NEXT
SETUP INSTRUCTIONS
AD-14
Duplex Unit
CF1501/CF2001
WARNING
• Before setting up this unit, be sure to unplug the power cord of the copier.
• Parts inside the copier are extremely hot. Before replacing the spring, be sure to wait approxi-
mately 20 minutes after turning off the copier and checking that the area around the fusing unit
has cooled down. In addition, touching any part other than those specified may result in burns.
CAUTION
• Keep all packing materials out of the reach of children.
• Before attaching the duplex unit, be sure that optional memory M128-2 is installed.
4657-7744-12
© MINOLTA CO., LTD.
Printed in Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
NEXT
Duplex Unit
4. Grasp the upper right-side door as shown,
7. Re-install the paper output cover.
and then carefully open the door completely
while making sure to support it.
NOTE
Be sure to support the door while carefully
opening it; otherwise, it may be damaged.
C4657U026AA
5. Remove the two screws securing the paper
output cover, and then remove the cover.
C4657U020AB
C4657U022AA
6. Remove the spring indicated in the illustra-
tion, and then replace it with the enclosed
spring.
8. Using the two screws, secure the paper out-
put cover.
NOTE
• Be sure to install the spring so that it is
oriented as shown in the illustration.
• The area around the fusing unit is
extremely hot. Touching any part other
than those specified may result in burns.
C4657U024AA
9. Close the upper right-side door.
C4657U023AA
4657-7744-12
– 2 –
Download from Www.Somanuals.com. All Manuals Search And Download.
NEXT
3. Plug the two connectors from the duplex unit
into the connectors on the copier.
Duplex Unit
■ Installing the Duplex Unit
1. Align the two tabs on the duplex unit with the two holes in the copier, and then install
the duplex unit.
C4657U009AA
C4657U013AA
C4657U005AA
NOTE
While supporting the duplex unit, open the
door on the right side of the copier, and
make sure that the tabs are secured within
the holes in the copier door.
C4657U010AA
C4657U006AA
4. Secure the cable of the duplex unit with the
cable holder as shown.
2. Open the duplex unit, and then secure the duplex unit to the copier with the enclosed
flat-head screws.
Firmly tighten the screws with a coin or screwdriver.
NOTE
Keep the duplex unit supported until it is secured with the screws.
C4657U017AA
5. Install the enclosed wiring cover.
C4657U011AA
C4657U007AA
C4657U008AA
4657-7744-12
– 3 –
Download from Www.Somanuals.com. All Manuals Search And Download.
NEXT
Duplex Unit
5. Touch “1st.”.
■ Checking and Adjusting the Paper Reference Position
NOTE
Perform the procedure below after adjusting the paper reference positions for the paper
feed unit and the large-capacity cabinet.
1. Display the Tech. Rep. Mode screen.
(For details about displaying the Tech. Rep.
Mode screen, refer to the Service Manual.)
C4657P002CA
6. Press the Start key.
A test page is printed.
C4658P001CA
2. Touch “Machine Adjust”.
C4004O068CA
7. Measure the width of loss for the test pattern
printed on the back of the test page.
3. Touch “PRT Area”.
a
NOTE
Do not measure from the back of the test
pattern.
Standard width (a): 3.0 mm ± 1.0 mm
C4659P004CA
If the measured width of loss does not meet
4. Touch “Dup. Left Margin”.
its standard width, touch
and
in the
lower-right corner of the screen to adjust the
width.
Print another test page and check the printed
image.
C4657U014AA
C4657P001CA
4657-7744-12
– 4 –
Download from Www.Somanuals.com. All Manuals Search And Download.
RETURN
Duplex Unit
8. Adjust the paper reference positions for the
2nd, 3rd and 4th drawers in the same way
(by repeating steps 5 through 7).
NOTE
The 4th drawer is only available if two
optional paper feed units are installed.
4657-7744-12
– 5 –
Download from Www.Somanuals.com. All Manuals Search And Download.
|