Insignia Indoor Furnishings NS WD1450 User Manual

USER GUIDE  
Espresso Finish Closed Cabinet  
TV Stand  
for TVs up to 50”/95 lbs  
NS-WD1450/NS-WD1450-C  
SAFETY INFORMATION AND SPECIFICATIONS....2  
PACKAGE CONTENTS: PARTS.....................................3  
PACKAGE CONTENTS: HARDWARE..........................4  
ASSEMBLY INSTRUCTIONS.........................................5  
CARE AND MAINTENANCE...................................... 19  
Before using your new product, please read these instructions to prevent any damage.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
PACKAGE CONTENTS: PARTS  
Make sure that you have all the parts necessary to assemble your new TV stand. While not all parts are  
labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts  
from each other. Use this part identification to help identify similar parts.  
A
B
C
D
E
F
G
H
I
Right End  
Left End  
1
1
1
1
1
1
1
2
2
2
K
L
Small Adjustable Shelf  
Long Skirt  
2
1
2
1
2
1
2
2
2
Right Upright  
Left Upright  
Top  
M
O
P
Short Skirt  
Top Molding  
Long Brace  
Bottom  
Back  
Q
R
Short Brace  
Side Brace  
Outer Back  
Door  
S
Inner Base Block  
Outer Base Block  
T
J
Large Adjustable Shelf  
E
O
A
G
H
C
K
J
D
J
H
K
F
B
P
R
P
T
M
Q
I
L
I
R
S
M
T
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ESPRESSO FINISH CLOSED CABINET TV STAND  
PACKAGE CONTENTS: HARDWARE  
Note: The table below shows the required hardware. You may receive extra hardware.  
Make sure that you have all the hardware necessary to assemble your new TV stand.  
Label  
U
Hardware  
Qty.  
8
Label  
CC  
Hardware  
Metal pin  
Qty.  
24  
Sauder  
twist-lock®  
fasteners  
Rubber sleeve  
Warning label  
DD  
EE  
16  
1
V
Hidden cam  
2
2
Cam dowel  
W
FF  
GG  
HH  
10  
14  
2
Large metal  
bracket  
X
Y
1
Black 1-7/8” flat head screw  
Silver 1-1/8” flat head screw  
Metal bracket  
Hinge  
18  
Gold 1” machine screw  
Z
4
II  
37  
AA  
BB  
Knob  
2
4
Black 9/16” large head screw  
JJ  
8
Felt discs  
Black 1/2” flat head screw  
Nail  
KK  
20  
1
2
3
4in  
10  
20  
30  
40  
50  
60  
70  
80  
90  
100mm  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ESPRESSO FINISH CLOSED CABINET TV STAND  
ASSEMBLY INSTRUCTIONS  
Step 1: Preparing the right and left ends and the uprights  
Caution: Assemble your stand on a carpeted floor or on the empty carton to avoid scratching your stand.  
• Push a Sauder twist-lock® fastener (U) into the large holes in the right and left ends (A and B) and uprights (C  
and D).  
NOTE: Do not tighten the Sauder twist-lock® fasteners at this time.  
U
B
A
D
C
You’ll need:  
U (8)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 2 Preparing the short brace  
:
Push two hidden cams (V) into the short brace (Q). Then, insert the metal end of a cam dowel (W) into  
each hidden cam (V).  
NOTE: Do not tighten the hidden cams in this step.  
Q
Arrow  
V
W
Arrow  
Insert the cam dowel into the hidden cam.  
You’ll need:  
W (2)  
V (2)  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 3 Preparing the top  
:
Fasten the top molding (O) to the top (E). Use six silver 1-1/8” flat head screws (GG).  
Finished surface  
s
e
l
o
h
h
t
i
w
e
c
a
f
O
r
u
E
S
Curved edge  
You’ll need:  
GG (6)  
Phillips screwdriver  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 4 Attaching the uprights to the top  
:
• Fasten the uprights (C and D) to the underside of the top (E), then tighten the four Sauder twist-lock®  
fasteners (U).  
To use the Sauder twist-lock® fasteners:  
1 Insert the dowel end of the fastener into the hole of the adjoining part.  
Note: The dowel end of the fastener must remain fully inserted in the hole of the adjoining part while locking the fastener.  
2 Tighten the fastener with a Phillips screwdriver as tight as possible.  
Dowel end  
D
S
w
u
r
t
f
-
t
a
c
i
e
s
w
®
l
o
i
f
t
a
h
c
k
o
u
t
S
e
s
a
t
u
e
n
d
e
C
r
s
r
S
w
u
r
t
f
-
t
a
c
i
s
e
w
®
l
i
f
o
t
a
h
c
k
S
a
u
d
s
e
s
t
e
r
n
e
r
E
Finished edge  
You’ll need:  
Phillips screwdriver  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 5 Attaching the outer backs  
:
1 Insert two metal pins (CC) into each side of the outer backs (H).  
2 Insert the metal pins (CC) in the outer backs (H) into the holes in the uprights (C and D).  
CC  
H
CC  
d
e
h
s
i
n
i
F
D
C
H
d
e
h
s
i
n
i
F
You’ll need:  
CC (8)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 6 Attaching the ends  
:
Fasten the ends (A and B) to the top (E), then tighten the four Sauder twist-lock® fasteners (U).  
Note: Make sure that the metal pins (CC) in the outer backs (H) insert into the holes in the ends (A and B).  
S
u
r
f
-
a
l
t
w
c
e
i
s
w
t
i
t
o
h
c
S
t
H
k
a
u
f
a
d
e
s
r
e
n
e
r
s
B
H
S
a
u
r
f
a
S
a
c
e
u
e
w
d
f
e
i
t
s
r
h
t
t
o
o
w
n
u
i
e
t
s
r
s
t
-
l
c
k
E
A
Finished edge  
Finished edge  
You’ll need:  
Phillips screwdriver  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 7  
:
Attaching the bottom and the short brace  
1 Fasten the bottom (F) to the ends (A and B) and the uprights (C and D) with eight black 1-7/8” flat head  
screws (FF).  
2 Fasten the short brace (Q) to the bottom (F), then tighten the two hidden cams (V).  
CAUTION: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not  
completely tightened may loosen and parts may separate.  
FF  
Surface with  
hidden cams  
FF  
Q
Curved edge  
F
d
e
h
s
i
n
i
f
u
e
n
s
c
a
U
f
B
r
D
C
A
START  
TIGHTEN  
Arrow  
CAUTION  
Risk of damage or  
Arrow  
Maximum  
injury. Hidden cams  
must be completely  
tightened. Hidden  
cams that are not  
completely tightened  
may loosen and parts  
may separate.  
210 degrees  
Minimum  
190 degrees  
You’ll need:  
FF (8)  
Phillips screwdriver  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 8 Preparing the braces  
:
• Fasten the eighteen metal brackets (Y) to the long braces (P) and side braces (R) with eighteen black 9/16” large  
head screws (II).  
Note: Make sure that the brackets are even with the edges of the braces.  
Unfinished  
surface  
Y
Y
P
P
Y
Unfinished  
surface  
Y
Y
R
R
You’ll need:  
Y (18)  
II (18)  
Phillips screwdriver  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 9 Attaching the braces  
:
1 Fasten the long braces (P) to the bottom (F) with eight black 9/16” large head screws (II).  
2 Fasten the long braces (P) to the short brace (Q) with two black 1-7/8” flat head screws (FF).  
3 Fasten the side braces (R) to the bottom (F) and long braces (P) with ten black 9/16” large head screws (II).  
Surface without  
metal brackets  
R
FF  
P
F
Surface without  
metal brackets  
Q
P
R
FF  
Surface without  
metal brackets  
You’ll need:  
FF (2)  
II (18)  
Phillips screwdriver  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 10 Attaching the base blocks and skirts  
:
1 Fasten the base blocks (S and T) to the long brace (P) with eight silver1-1/8” flat head screws (GG).  
Note: There are no pre-drilled holes in the base blocks. The screws will tighten into the grooves in the base blocks. The  
outer base blocks (T) have only one notch and the inner base blocks (S) have two notches. Pay close attention to  
the positioning of the base blocks.  
2 Fasten the large metal bracket (X) to the bottom (F) with a black 9/16” large head screw (II).  
3 Insert the skirts (L and M) into the notches in the base blocks.  
Note: Make sure that the long skirt (L) is positioned in front of the large metal bracket.  
M
d
e
h
s
i
n
i
F
Notch should be  
located here  
L
d
e
h
s
i
n
i
F
M
d
T
e
h
s
i
n
i
F
S
F
P
S
Notch should be  
located here  
T
X
You’ll need:  
Phillips screwdriver  
GG (8)  
X (1)  
II (18)  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 11 Attaching the back  
:
1 Carefully turn over your TV stand onto its front edges. Unfold the back (G) and lay it over the unit.  
2 Make sure the back is centered along all four edges. Push on opposite corners, if required, to make it square.  
3 Fasten the back (G) to the unit with nails (KK).  
Note: Perforations have been provided for access through the back. Carefully cut out the holes, as needed.  
CAUTION: Do not stand the unit upright without the back fastened. The unit may collapse.  
The perforations should  
be positioned here  
e
c
a
f
r
u
s
G
d
e
h
s
i
n
i
f
n
U
You’ll need:  
KK (20)  
Hammer  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 12 Attaching the doors  
:
1 Carefully stand your unit upright.  
2 Fasten two hinges (Z) to each door (I). Use four black 1/2” flat head screws (JJ) on each door.  
3 Fasten the first door (I) to the right end (A) and the second door (I) to the left end (B). Use the screws in the  
hinges.  
a. Loosen the mounting screw on both hinges, then slide the hinge apart.  
b. Tighten the vertical adjusting screws on the hinge plates partway into the right end (A).  
c. Slide the hinges back together by aligning the door (I) with right end (A) then tighten the vertical  
adjustment screws and mounting screws.  
d. Repeat steps a-c for to attach the second door (I) to the left end (B).  
4 Fasten a knob (AA) to each door (I). Use the gold 1” machine screws (HH).  
5 Stick two felt disks (BB) on each door (I) where it comes in contact with the uprights (C or D).  
3a  
I
Hinge plate  
Z
3c  
Horizontal  
adjustment screw  
A
Mounting  
screw  
(depth)  
I
C
AA  
Vertical adjustment  
screw  
HH  
BB  
You’ll need:  
HH (2)  
JJ (8)  
BB (4)  
AA (2)  
Z (4)  
Phillips screwdriver  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 13 Adjusting the doors  
:
Refer to the enlarged diagram to identify the parts on the hinges.  
The doors may need some adjustments. Follow the text below to make needed adjustments.  
DOOR ADJUSTMENTS:  
• To adjust the doors from side to side (horizontal), loosen the horizontal adjustment screws several turns, then  
turn the adjusting screw in or out. Tighten the mounting screw after making adjustments.  
• To adjust the doors up and down (vertical), loosen both sets of vertical adjustment screws. Move the doors up or  
down to the desired location. Tighten the screws after making adjustments.  
• To adjust the doors in or out (depth), loosen the mounting screws one turn and move the doors in or out, as  
needed. Tighten the mounting screws after making adjustments.  
Horizontal  
adjustment screw  
Mounting screw (depth)  
Vertical adjustment screw  
You’ll need:  
Phillips screwdriver  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 14 Attach miscellaneous hardware and labels  
:
1 Push the rubber sleeves (DD) over one end of each metal pin (CC). Insert the metal end of the pins into the hole  
locations of your choice in the ends (A and B) and uprights (C and D). Set the adjustable shelves (J and K) onto  
the metal pins.  
2 Apply the warning label (EE) to the top (E). You should be able to read the label when the TV is removed from  
the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in  
the diagram.  
Note: This is a permanent label intended to last for the life of the product. After it is applied, do not try to remove it.  
Note: Please read the back pages of this instruction booklet for important safety information.  
3 This completes the assembly. Clean your TV stand with your favorite furniture polish or a damp cloth, then wipe  
dry.  
WARNING  
Never use this furniture with a TV that  
is too large or too heavy. Severe injury  
or death can occur. The TV and  
furniture will be unstable and may tip.  
- The TV must weigh less than 95 lbs.  
- The base of the TV must be able to  
sit completely on this shelf.  
EE  
E
K
95 lbs.  
20 lbs.  
A
C
J
J
25 lbs.  
25 lbs.  
K
20 lbs.  
B
60 lbs.  
D
CC  
DD  
You’ll need:  
DD (16)  
CC (16)  
EE (1)  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPRESSO FINISH CLOSED CABINET TV STAND  
CARE AND MAINTENANCE  
Wood/Laminate  
• Use your favorite type of furniture polish.  
• Do not spray polish directly onto the stand. Spray onto a soft cloth then wipe the stand.  
• Always test any polish in a discrete location first, such as the back of the stand, to make sure that there is no  
adverse reaction.  
• Dust frequently with a soft cloth.  
• Never slide objects across surfaces. Lift objects from the top surface rather than dragging them across the finish  
when moving them.  
• Do not expose your stand to direct sunlight, drying heat sources, or dampness.  
Glass  
• Use a commercial liquid glass cleaner and a soft cloth.  
• Do not use harsh powders or any other abrasive substances as they will scratch the glass.  
• Clean spills immediately with a soft, damp cloth.  
• Protect surfaces by using felt, leather, or cork under accessories.  
• Use a protective pad when using your stand as a writing surface (especially when using a ballpoint pen).  
• Dust frequently with a soft cloth.  
WARNING  
Please use your stand correctly and safely. Improper use can cause safety hazards or damage to your furniture or household items. Carefully read  
the following chart.  
Look out for:  
What can happen:  
How to avoid the problem:  
• Children climbing on the stand.  
• Risk of injury or death.  
• Never allow children to climb on or play with the stand.  
• A child may try to reach a toy or other object by climbing • A child climbing on the stand can make it top-heavy and • Do not place toys or food on the top shelves. Children may  
on the stand.  
• Children will play and be active near the TV.  
cause it to tip over.  
• A child playing with a TV can cause it to tip over.  
try to climb to reach them out of curiosity.  
• Improper use of the stand to support TVs.  
• Risk of injury or death.  
• A TV must only be set on furniture specifically designed to  
support a television.  
• Never use a TV that exceeds the weight ratings or size  
guidelines specified for the stand.  
• The stand is designed for use with TVs will specify the • TVs can be very heavy. Note, older CRT TVs tend to be  
maximum weight rating and recommended size of the  
TVs it will safely support.  
unbalanced and prone to tipping forward.  
• Overloaded shelves  
• Risk of injury.  
• Top-heavy furniture can tip over.  
• Overloaded shelves can break.  
• Never exceed the weight limits shown in the instructions.  
• Work from the bottom to the top when loading shelves.  
• The bottom shelves can only support 25 lbs. while the top  
can support 95 lbs.  
• Improperly moving the stand.  
• The stand can tip over or break if improperly moved.  
• Risk of injury.  
• Unload shelves from the top to the bottom before moving  
the stand.  
• Do not push the stand, especially on a carpeted floor. Have a  
friend help you lift the item and set it in place.  
• Do not lift the stand using the top shelf. Lift from the frame  
or leg assembly.  
• Remove the TV before moving the TV stand.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ESPRESSO FINISH CLOSED CABINET TV STAND  
Modification of any part of the Product, including the  
antenna  
ONE-YEAR LIMITED  
Display panel damaged by static (non-moving) images  
WARRANTY - INSIGNIA  
applied for lengthy periods (burn-in).  
Damage due to incorrect operation or maintenance  
Connection to an incorrect voltage or power supply  
Attempted repair by any person not authorized by Insignia  
to service the Product  
Definitions:  
The Distributor* of Insignia branded products warrants to you,  
the original purchaser of this new Insignia-branded product  
(“Product”), that the Product shall be free of defects in the  
original manufacturer of the material or workmanship for a  
period of one (1) year from the date of your purchase of the  
Product (“Warranty Period”).  
Products sold “as is” or “with all faults”  
Consumables, including but not limited to batteries (i.e. AA,  
AAA, C etc.)  
Products where the factory applied serial number has been  
altered or removed  
For this warranty to apply, your Product must be purchased in  
the United States or Canada from a Best Buy branded or Future  
Shop branded retail store or online at www.bestbuy.com,  
www.bestbuy.ca, or www.futureshop.ca and is packaged with  
this warranty statement.  
Loss or Theft of this product or any part of the product  
Display panels containing up to three (3) pixel failures (dots  
that are dark or incorrectly illuminated) grouped in an area  
smaller than one tenth (1/10) of the display size or up to  
five (5) pixel failures throughout the display. (Pixel based  
displays may contain a limited number of pixels that may  
not function normally.)  
How long does the coverage last?  
Failures or Damage caused by any contact including but  
not limited to liquids, gels or pastes.  
The Warranty Period lasts for 1 year (365 days) from the date you  
purchased the Product. Your purchase date is printed on the  
receipt you received with the Product.  
REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS  
YOUR EXCLUSIVE REMEDY FOR BREACH OF WARRANTY. INSIGNIA  
SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR  
What does this warranty cover?  
CONSEQUENTIAL DAMAGES FOR THE BREACH OF ANY EXPRESS  
OR IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, BUT  
NOT LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT,  
LOST BUSINESS OR LOST PROFITS. INSIGNIA PRODUCTS MAKES  
NO OTHER EXPRESS WARRANTIES WITH RESPECT TO THE  
PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR THE  
PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED  
WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN  
During the Warranty Period, if the original manufacture of the  
material or workmanship of the Product is determined to be  
defective by an authorized Insignia repair center or store  
personnel, Insignia will (at its sole option): (1) repair the Product  
with new or rebuilt parts; or (2) replace the Product at no charge  
with new or rebuilt comparable products or parts. Products and  
parts replaced under this warranty become the property of  
Insignia and are not returned to you. If service of Products or  
parts are required after the Warranty Period expires, you must  
pay all labor and parts charges. This warranty lasts as long as you  
own your Insignia Product during the Warranty Period. Warranty  
coverage terminates if you sell or otherwise transfer the Product.  
DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND  
NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY  
AFTER THE WARRANTY PERIOD. SOME STATES, PROVINCES AND  
JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN  
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT  
APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL  
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY  
FROM STATE TO STATE OR PROVINCE TO PROVINCE.  
Contact Insignia:  
For customer service please call 1-877-467-4289  
How to obtain warranty service?  
If you purchased the Product at a Best Buy or Future Shop retail  
store location, please take your original receipt and the Product  
to any Best Buy or Future Shop store. Make sure that you place  
the Product in its original packaging or packaging that provides  
the same amount of protection as the original packaging. If you  
purchased the Product from a Best Buy or Future Shop online  
INSIGNIA is a trademark of Best Buy and its affiliated companies.  
Registered in some countries.  
to the address listed on the web site. Make sure that you put the  
Product in its original packaging or packaging that provides the  
same amount of protection as the original packaging.  
To obtain warranty service, in the United States call  
1-888-BESTBUY, Canada call 1-866-BESTBUY for Future Shop call  
1-800-663-2275. Call agents may diagnose and correct the issue  
over the phone.  
Distributed by Best Buy Purchasing, LLC  
7601 Penn Ave South, Richfield, MN 55423 U.S.A.  
©2014 Best Buy. All rights reserved.  
Made in USA with U.S. and imported materials  
Where is the warranty valid?  
This warranty is valid only in the United States and Canada at  
Best Buy or Future Shop branded retail stores or websites to the  
original purchaser of the product in the county where the  
original purchase was made.  
What does the warranty not cover?  
This warranty does not cover:  
Customer instruction/education  
Installation  
Set up adjustments  
Cosmetic damage  
Damage due to weather, lightning, and other acts of God,  
such as power surges  
Accidental damage  
Misuse  
Abuse  
Negligence  
Commercial purposes/use, including but not limited to use  
in a place of business or in communal areas of a multiple  
dwelling condominium or apartment complex, or  
otherwise used in a place of other than a private home.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Certificate of Conformity  
1. This certificate applies to the Insignia Product  
identified by this instruction booklet.  
2. This certificate applies to the compliance of this  
product with the CPSC Ban on Lead-Containing  
Paint (16 CFR 1303).  
3. This product was manufactured for:  
Insignia  
4. Date of Manufacture: _______________  
Lot number: 361832  
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)  
INSIGNIA is a trademark of Best Buy and its affiliated companies.  
Registered in some countries.  
Distributed by Best Buy Purchasing, LLC  
7601 Penn Ave South, Richfield, MN 55423 U.S.A.  
©2014 Best Buy. All rights reserved.  
Made in USA with U.S. and imported materials  
V3 ENGLISH  
14-0647  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Washer IWC 6103 User Manual
Insignia DVD Player NS C2115 User Manual
Intec Vacuum Cleaner 8940 20 User Manual
Integra Speaker System MZA 47 User Manual
Ives Indoor Furnishings VR900 User Manual
JVC Car Speaker CS GD4250 User Manual
JVC CRT Television HV 32P37SUE HV 28P37SUE User Manual
Kawasaki Automobile Parts KX100D5 User Manual
Kodak Printer KY0730482 User Manual
Koss Telephone JR170 RF User Manual