Insignia Digital Camera HCC334L User Manual

L-Series

Color Camera

PAL

NTSC

HCC334L

HCC484L

HCC334LX

HCC484LX

HCC335LX

HCC485LX

User Guide

Document G-113077-001 – 02/07 – Rev 3

Download from Www.Somanuals.com. All Manuals Search And Download.

Warnings

Installation and servicing should be performed only by

qualified and experienced personnel to conform to all local

codes and to maintain your warranty.

WARNING! 12 VDC/24 VAC models require the use

of CSA Certified/UL Listed Class 2

power adapters to ensure compliance

with electrical safety standards.

Where the MAINS plug or an appliance coupler is used as

the disconnect device, the disconnect device shall remain

readily operable.

WEEE (Waste Electrical and Electronic Equipment).

Correct disposal of this product (applicable in the

European Union and other European countries with

separate collection systems). This product should be

disposed of, at the end of its useful life, as per applicable

local laws, regulations, and procedures.

Explanation of Graphical

Symbols

THIS SYMBOL INDICATES THAT

DANGEROUS VOLTAGE

CONSTITUTING A RISK OF

ELECTRIC SHOCK IS PRESENT

CAUTION

RISK OF ELECTRIC

SHOCK

DO NOT OPEN

WITHIN THE UNIT.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE THE COVER.

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL

THIS SYMBOL INDICATES THAT

IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS

ACCOMPANY THIS UNIT.

Rev 3

iii

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

FCC Compliance Statement

Information to the User: This equipment has been tested

and found to comply with the limits for a Class A digital

device. Pursuant to Part 15 of the FCC Rules, these limits

are designed to provide reasonable protection against

harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may

cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Caution Changes or modifications not expressly

approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

Manufacturer’s Declaration of

Conformance

The manufacturer declares that the equipment supplied

with this guide is compliant with the essential protection

requirements of the EMC directive 89/336/EEC and the Low

Voltage Directive LVD 73/23 EEC, conforming to the

requirements of standards EN 55013 for emissions.

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . 2

Unpack Everythin g . . . . . . . . . . . . . . . . . . . . . . . . 2

Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Camera Functions . . . . . . . . . . . . . . . . . . . . . . . . 3

Setting Up Your Camera . . . . . . . . . . . . . . . . . . . 4

Selecting the Lens . . . . . . . . . . . . . . . . . . . . . . 4

Manual Lens . . . . . . . . . . . . . . . . . . . . . . . 4

Vari-focal Auto Iris Lens . . . . . . . . . . . . . . . 4

Direct Drive (DC) Lens . . . . . . . . . . . . . . . . 4

Video Drive (VSD) Len s . . . . . . . . . . . . . . . 5

Exposure Mode . . . . . . . . . . . . . . . . . . . . . . . . 5

Automatic Exposure Mode . . . . . . . . . . . . . 5

Manual Exposure Mode . . . . . . . . . . . . . . 5

Backlight Compensation (BLC). . . . . . . . . . . . 6

Flickerless Mode (FL) . . . . . . . . . . . . . . . . . . . . 6

Automatic Gain Control (AGC) . . . . . . . . . . . . 6

Auto White Balance (AWB) . . . . . . . . . . . . . . . 6

Auto Trace White Balance (ATW) . . . . . . . 6

Auto White Balance Control (AWC). . . . . . 7

One Push Lock . . . . . . . . . . . . . . . . . . . . . . 7

Synchronization Selection (LL/INT) . . . . . . . . . 7

Line Lock Phase Adjustment Potentiometer. . 8

Lens Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Adjusting the Back Focus . . . . . . . . . . . . . . . . . . . 9

Completing the Installation . . . . . . . . . . . . . . . . . . 11

Mounting the Camera . . . . . . . . . . . . . . . . . . . . . 11

Connecting the Camera . . . . . . . . . . . . . . . . . . . 12

Warranty and Service . . . . . . . . . . . . . . . . . . . . . . 13

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

The Honeywell L-Series Color cameras are ideally suited

for use in day-to-day surveillance applications. The L-

Series cameras are designed for exceptional value and

performance for everyday use. Their off-the-shelf feature

set is designed for high picture quality in standard

applications and they require little to no adjustment after

installation.

Figure 1

Camera Overview

C/CS mount adapter:

C mount: turn

counterclockwise

Lens connector for

Auto Iris lens plug

CS mount: turn clockwise

Setscrew: loosen locking ring

with a Phillips screwdriver to

adjust mounting ring.

Features

•

1/3” CCD

C/CS adjustable lens mount adapter

Excellent signal-to-noise ratio of more than 50 dB

Minimum illumination:

•

High Res — 0.4 lux (F1.2, 50 IRE, AGC ON)

Standard Res — 0.2 lux (F1.2, 50 IRE, AGC ON)

•

2-way Auto Iris: Video Iris (VSD) or Direct Drive (DC)

Iris lens

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Before You Begin

Please read this guide carefully

before you install the L-Series Color

camera.

Keep this guide for future reference.

Unpack Everything

Check that the items received match those listed on the

order form and packing slip. The L-Series packing box

should include, in addition to this User Guide:

•

One L-Series Color camera

One Auto Iris lens plug

If any parts are missing or damaged, contact the dealer you

purchased the camera from or call Honeywell Customer

Service (see Contact Information on the back of this

manual).

Note

You will also require a Phillips screwdriver to

complete the installation.

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Camera Settings

Camera Functions

Figure 2

Camera Rear View

Mains 230V —Line Voltage

(HCC335LX, HCC485LX)

Low Voltage

(HCC334L/X, HCC484L/X)

ID EO

IR IS

V ID

V-P

E L

L O C

IR IS

L E

V-P

P U

P W

A E

L /L

~2 0 7 -2 5 3 VAC 5 0 H

S D

AGC

O FF

12V

24V

Legend

Description

DIP switches for mode settings (see Figure 3)

Auto Iris Lens select switch, VSD for Video or DC for Direct

Drive

Sync select switch

Video output connector

Power input connector (24 VAC: 3 terminals)—Low Voltage

model only

Power LED indicator

DC Iris level adjustment, for use with DC Iris lens

V-Phase adjustment, for use with Line lock

Push Lock in White Balance (WB) mode

EEPROM data setting for factory use only

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Up Your Camera

Figure 3 shows the factory set DIP switch settings.

Automatic Gain Control (AGC) and Auto White Balance

Control (AWC) are set ON.

Figure 3

Factory Set DIP Switch Settings

IRIS

LEVEL

VIDEO

PUSH IRIS

AES

OFF

LOCK LEVEL V- PH

PWR

L/L

BLC

AES

BLC INT

VSD

AGC

WB3

WB2

OFF

VSD

AGC

WB3

WB2

WB1

DC 12V

AC 24V

WB1

GND

= ON

= OFF

Selecting the Lens

Manual Lens

Set the EE/ME DIP switch on the rear of the camera (see

Figure 3) to EE. Set the AES/AI switch to AES. EE and AES

are the typical settings.

Vari-focal Auto Iris Lens

Vari-focal Auto Iris lenses (Direct Drive [DC] or Video Drive

[VSD]) are connected to the camera via a 4-pin square

socket located at the side of the camera. Set the AES/AI

DIP switch to AI. EE and AI are the typical settings.

To set a different exposure, see Exposure Mode on page 5.

Direct Drive (DC) Lens

1. Set the VSD/DC switch on the rear of the camera to

DC. Set the AES/AI DIP switch to AI.

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Slowly turn the LEVEL potentiometer until the picture

on the monitor is as clear as possible and is not too

bright.

Video Drive (VSD) Lens

Set the VSD/DC switch on the rear of the camera (see

Figure 3) to VSD.

Exposure Mode

Automatic Exposure Mode

The Electronic Exposure feature compensates for

excessive light levels by automatically adjusting the shutter

speed of the camera. Set the EE/ME switch to EE

(recommended setting).

Manual Exposure Mode

Set the EE/ME switch to ME. This setting is typically used

only in machine vision applications. The table below gives

the shutter speeds for the switch settings.

Switch Label

Shutter

BLC

AES/AI

speed(s)

1/50 (PAL)

1/60 (NTSC)

OFF

AES

OFF

1/100 (PAL)

OFF

BLC

1/120 (NTSC)

1/250

OFF

AGC

WB3

WB2

WB1

1/500

1/1000

1/2000

1/4000

1/10000

OFF

= ON

= OFF

LEGEND

OFF

Caution Before you adjust the shutter speed, it is

important that you understand how the settings

can affect the scene detail.

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Backlight Compensation (BLC)

If there is excessive light (for example, a window exists in a

scene), the camera tries to compensate by reducing the

overall exposure, resulting in the areas surrounding the

window becoming too dark. Turn the BLC switch ON to

eliminate the silhouette effect.

Flickerless Mode (FL)

Set the FL switch to ON to remove the flicker in a picture.

For PAL models, the shutter speed is 1/100 second; for

NTSC models, the shutter speed is 1/120 second.

Automatic Gain Control (AGC)

This feature can improve picture quality when the level of

scene illumination is low. When set to OFF, the gain is 11

dB. When set to ON, the gain is 30 dB.

Auto White Balance (AWB)

Auto white balance ensures that color integrity is

maintained. To set the white balance, change the WB1,

WB2, or WB3 switches as shown in the following table.

WB1 WB2 WB3 AWB Mode

OFF OFF OFF ATW Mode

ME OFF ON

OFF AWC Mode

ON One Push Lock

AES

OFF

OFF ON

BLC

OFF OFF Indoor Fixed Mode (3200°K)

AGC

WB3

WB2

WB1

OFF ON

Fluorescent Fixed Mode

(4200°K)

OFF User Fixed Mode (4700°K)

ON Outdoor Fixed Mode (6300°K)

= ON

= OFF

LEGEND

Auto Trace White Balance (ATW)

This mode covers a range of 2800°K to 8000°K. This mode

is typically used for indoor applications.

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto White Balance Control (AWC)

This mode covers a wider range of 2000°K to 10000°K and

performs at a faster operating speed than ATW mode. This

mode is typically used for outdoor applications or where

variable lighting conditions exist.

One Push Lock

Press PUSH LOCK on the rear of the camera to calibrate

the white balance for the current scene. This mode is

typically used for scenes with constant lighting conditions.

Synchronization Selection (LL/INT)

This switch selects the synchronization mode of the

camera. When the camera is connected to an AC supply,

the Line lock (LL) mode is used to lock the camera’s frame

rate to the frequency so that each camera in the system is

triggered at the same point on the supply’s AC cycle. The

default setting is LL.

WARNING! The LL/INT switch must be set to INT

when operating from 12 VDC.

V-PH

VIDEO

PUSH

IRIS

L/L

LOCK LEVEL V-PH

PWR

L/L

AES

BLC INT

VSD

AGC

WB3

WB2

OFF

DC 12V

AC 24V

WB1

INT

GND

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Line Lock Phase Adjustment

Potentiometer

When the camera is in Line lock mode, it is possible to

adjust the point on the AC cycle at which the camera

triggers. This feature allows for synchronization of cameras

that are connected to different phases.

The V-PHASE adjustment potentiometer allows the line

lock phase trigger point to be adjusted by 270°. Rotating

the potentiometer clockwise advances the trigger point and

turning it counterclockwise retards the trigger point. The

factory default setting is the zero crossing point. If all

cameras in a system are on the same phase then no line

lock phase adjustment should be made.

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Lens Installation

Adjusting the Back Focus

The back focus adjustment is accessible at the front end of

the camera housing to adjust the back focal length or

picture focus.

The range of adjustment allows both C- and CS-mount

lenses to be used without the need for a spacer ring.

Figure 4

C/CS Mount

Setscrew

1. Loosen the setscrew with a Phillips screwdriver.

2. Adjust the focus ring to focus the picture.

3. Retighten the setscrew.

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 5

DC and VSD Lens Pin Definition

Auto Iris lens connector

Pin DC (Direct Drive) lens

Video (VSD) lens

Power (+12V)

CTRL -

CTRL +

DRV +

Video Signal

GND

DRV -

Set the select switch to DC

Set the select switch to VSD

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Completing the Installation

Mounting the Camera

Mounting points are provided on the top of the camera for

mounting the camera on a bracket or tripod. They are

designed to accept standard sized 1/4 x 20 mounting

screws. This bracket can be unscrewed and mounted onto

the opposite side of the camera, depending on your

application. The mounting bracket must be capable of

supporting the weight of the camera and its lens.

Note

Some installation codes dictate that the mounting

bracket must be capable of supporting up to four

times the combined weight of the camera and

lens.

Figure 6

Camera Mount

Unscrew 3 bracket

securing screws and

then resecure the

bracket on the other

side of the camera.

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the Camera

1. Connect the VIDEO connector on the rear of the

camera to the video-in connector on your monitor.

2. Connect the camera to a power supply appropriate for

your installation.

HCC334L/X, HCC484L/LX: 12 VDC or 24 VAC power

supply

HCC335LX, HCC485LX: 230V power supply

3. Plug in the power supply. The power (PWR) LED

illuminates to show that the camera is receiving power.

If it does not illuminate, check the connections and the

power source.

Figure 7

Camera Connections

Low voltage model shown

(HCC334L/X, HCC484L/X)

Monitor

V ID E O

P U S H

L O C K

IR IS

L E V E L

V-P H

P W

L /L

E E

M E

A I

Power LED

A E S

B LC

IN T

V S D

AGC

OFF

B 3

B 2

B 1

12V

AC 24V

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Warranty and Service

Subject to the terms and conditions listed on the Product warranty,

during the warranty period Honeywell will repair or replace, at its

sole option, free of charge, any defective product returned prepaid.

In the event you have a problem with any Honeywell product,

please call Customer Service at 1.800.796.CCTV (North America

only) for assistance or to request a Return Merchandise

Authorization (RMA) number. For Europe and the United

Kingdom, please contact your Honeywell dealer.

Be sure to have the model number, serial number, and the nature

of the problem available for the technical service representative.

Prior authorization must be obtained for all returns, exchanges, or

credits. Items shipped to Honeywell without a clearly identified

Return Merchandise Authorization (RMA) number may be

refused.

Specifications

Note

These specifications refer to all models, except

where otherwise noted.

HCC334L HCC334LX HCC484L HCC484LX

HCC335LX

HCC485LX

Operational

Image Sensor:

1/3” Super HAD CCD

Video

NTSC

PAL

NTSC

PAL

Standard:

Scanning

System:

525 lines,

625 lines,

525 lines,

625 lines,

2:1 interlace 2:1 interlace 2:1 interlace 2:1 interlace

Number of

510 x 492 500 x 582 768 x 494 752 x 582

Pixels (H x V):

Minimum

Illumination:

< 0.2 lux @ F1.2

(50 IRE, AGC ON)

330 TVL 330 TVL

< 0.4 lux @ F1.2

(50 IRE, AGC ON)

480 TVL 480 TVL

Horizontal

Resolution:

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

HCC334L HCC334LX HCC484L HCC484LX

HCC335LX

HCC485LX

Video Output:

Sync System:

S/N Ratio:

1 Vp-p @ 75 Ohms

Internal/Line lock

> 50 dB

Auto Gain

On (30 dB)/Off (11 dB)

Control (AGC):

ALC:

EE/VSD/DC

Automatic

Electronic

Shutter (AES): sec

1/60 -

1/100,000

1/50 -

1/100,000

sec

1/60 -

1/100,000

sec

1/50 -

1/100,000

sec

Lens Mount:

C/CS mount (adjustable)

White Balance

(AWB):

ATW/AWC/One Push Lock/Indoor/Outdoor/

Fluorescent/User

BLC:

On/Off

0.45

Gamma:

Electrical

Input Voltage: HCC334L/LX, HCC484L/LX: 12 VDC/24 VAC

HCC335LX, HCC485LX: 230 VAC

Input Voltage

Range:

HCC334L/LX, HCC484L/LX: 11 - 16 VDC, 17 - 28 VAC

HCC335LX, HCC485LX: 230 VAC 10%

HCC334L/LX, HCC484L/LX: 3.5 W

Power

Consumption:

HCC335LX, HCC485LX: 4.2 W (max)

Mechanical

Dimension:

(W x H x D)

HCC334L/LX, HCC484L/LX: 2.68 x 2.2 x 4.72 in. (68 x

56 x 120 mm)

HCC335LX, HCC485LX: 2.68 x 2.2 x 5.51 in. (68 x 56 x

140 mm)

Weight:

HCC334L/LX, HCC484L/LX: 0.84 lb (.380 kg)

HCC335LX, HCC485LX: 0.90 lb (.410 kg)

Environmental

Temperature:

Operating: 14°F to 122°F (-10°C to +50°C)

Storage: -4°F to158°F (-20°C to +70°C)

Regulatory

Emissions:

Immunity:

Safety:

FCC, CE (EN55013)

CE (EN50130-4)

EU: 73/23/EEC LVD

Rev 3

G-113077-001

02/07

Download from Www.Somanuals.com. All Manuals Search And Download.

Honeywell Video Systems (Head office) Honeywell Video Systems

2700 Blankenbaker Pkwy, Suite 150

Louisville, KY 40299, USA

www.honeywellvideo.com

℡ +1.800.796.2288

Northern Europe

Netwerk 121

1446 WV Purmerend, The Netherlands

www.SecurityHouse.nl

℡ +31.299.410.200

Honeywell Security Australia Pty Ltd.

Unit 5, Riverside Centre

24-28 River Road West

Parramatta, NSW 2150, Australia

www.ademco.com.au

Honeywell Video Systems UK Ltd.

Aston Fields Road, Whitehouse Ind Est

Runcorn, Cheshire, WA7 3DL, UK

www.honeywellvideo.com

℡ +61.2.8837.9300

℡ +0844 8000 235

Honeywell Security Asia Pacific

33/F Tower A, City Center, 100 Zun Yi

Road

Shanghai 200051, China

www.security.honeywell.com/cn

℡ +86 21.2527.4568

Honeywell Security South Africa

Unit 6 Galaxy Park, 17 Galaxy Avenue

Linbro Park, P.O. Box 59904

2100 Kengray, Johannesburg

South Africa

www.honeywell.co.za

℡ +27.11.574.2500

Honeywell Security Asia

Flat A, 16/F, CDW Building

388 Castle Peak Road

Tsuen Wan, N.T., Hong Kong

www.security.honeywell.com/hk

℡ +852.2405.2323

Honeywell Security Deutschland

Johannes-Mauthe-Straße 14

D-72458 Albstadt, Germany

www.honeywell.com/security/de

℡ +49.74 31.8 01.0

Honeywell Security France

Parc Gutenberg, 8, Voie La Cardon

91120, Palaiseau, France

www.honeywell.com/security/fr

℡ +33.01.64.53.80.40

Honeywell Security Poland

Chmielewskiego 22a, 70-028

Szczecin, Polska

www.ultrak.pl

℡ +48.91.485.40.60

Honeywell Security Italia SpA

Via Treviso 2 / 4

31020 San Vendemiano

Treviso, Italy

Honeywell Security Czech Republic

Havránkova 33, Brno

Dolní Heršpice, 619 00

Czech Republic

www.honeywell.com/security/it

℡ +39.04.38.36.51

www.olympo.cz

℡ +420.543.558.111

Honeywell Security España

Mijancas 1. 3^aPlanta

P.Ind. Las Mercedes

Honeywell Security Slovakia Republic

Vajnorská 142, 83104 Bratislava

Slovakia

28022 Madrid, Spain

www.honeywell.com/security/es

℡ +34.902.667.800

www.olympo.sk

℡ +421.2.444.54.660

www.honeywellvideo.com

+1.800.796.CCTV (North America only)

[email protected]

Document G-113077-001 02/07 Rev 3

may be reproduced by any means without written permission from Honeywell Video

Systems. The information in this publication is believed to be accurate in all respects.

However, Honeywell Video Systems cannot assume responsibility for any

consequences resulting from the use thereof. The information contained herein is

subject to change without notice. Revisions or new editions to this publication may

be issued to incorporate such changes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Indesit Washer Dryer WIXL 163 S User Manual
Inter Tel Cordless Telephone INT1100 User Manual
Jensen TV DVD Combo FPE1908DVDC 19 User Manual
JVC Car Stereo System KW AVX800 User Manual
Jwin MP3 Player JX CD573 User Manual
KEF Audio Speaker XQ10 User Manual
Kettler Patio Furniture 1072 000 User Manual
Kidde Smoke Alarm SMOKE AND CARBON MONOXIDE ALARM User Manual
KitchenAid Blender KFP715BW2 User Manual
KitchenAid Refrigerator KBLS19KTSS4 User Manual