Infinity Stereo System 11cs User Manual

653.1cs, 1.1cs  
I N ST R U C T I O N S  
KAPPASERIES  
®
Thank you  
for purchasing an Infinity Kappa Series 3-Way  
Component System. We’ve organized this manual to make your installation  
as simple and trouble-free as possible. Please read it thoroughly before  
proceeding. Remember to keep your sales receipt with this manual in a  
safe place so both are available for future reference.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MIDRANGE INSTALLATION  
TWEETER INSTALLATION  
Bi-Amp  
RIGHT  
+
GRN  
GRN/WHT  
Amplifier  
To Woofer Amplifier  
RIGHT  
GRN/BLK  
+
(Tweeter & Mids)  
GRN  
+
sacle = 70%  
+
LEFT  
RED  
RED  
Connect Pigtail  
Jumpers As Shown  
+
+
BLK  
BLK  
+
+
+
+
+
+
W O O F E R  
M I D R A N G E  
E M I T T W E E T E R  
E M I T T W E E T E  
M
R I D R A N G E  
W O O F E R  
RIGHT  
F R O M L E F T A M P L I F I E R S  
F R O M R I G H T A M P L I F I E R S  
+
Amplifier  
(Woofers)  
BLU/BLK  
BLU/WHT  
+
To LEFT  
Woofer  
+HI  
To RIGHT  
Woofer  
LEFT  
REFERENCE STANDARD AUTOMOTIVE  
Component System Crossover Network  
HI +  
TO LEFT  
TO LEFT  
TO RIGHT  
TO RIGHT  
BLU  
BLU  
Figure 5. Installing a Kappa 1.1cs/653.1cs midrange driver  
in a door panel.  
MIDRANGE  
TWEETER  
TWEETER  
MIDRANGE  
+
+
+
+
LO  
HI  
LO MID HI  
HI MID LO  
HI  
LO  
GRY/ RED/  
RED/ GRY/  
BLK  
BLK  
WHT  
WHT  
Figure 6. After installing the surface-mount plate, slide the  
Kappa1.1cs EMIT-N™ tweeter down on the plate to lock in  
place.  
GRY  
+HI  
RED  
RED  
GRY  
+HI  
To LEFT  
To RIGHT  
Figure 2.This application shows  
connections for a Kappa1cs sys-  
tem and two stereo amplifiers.  
WOOFER INSTALLATION  
4"Midrange  
4"Midrange  
+MID  
+MID  
Tri-Amp  
To LEFT  
Tweeter  
To RIGHT  
Tweeter  
Figure 4. Installing a Kappa1.1cs/653.1cs woofer  
above a deck or (with the enclosed spacer) below  
a deck.  
NOTE: Use the mounting clips as nuts to secure  
the below-deck installation.  
RIGHT  
+
GRN  
GRN/WHT  
Amplifier  
(Tweeters)  
To Midrange Amplifier  
RIGHT  
GRN/BLK  
GRN  
+
LEFT  
To Woofer Amplifier  
RIGHT  
+
+
+
+
+
+
+
+
W O O F E R  
M I D R A N G E  
E M I T T W E E T E R  
E M I T T W E E T E  
M
R I D R A N G E  
W O O F E R  
Remove Pigtail  
F R O M L E F T A M P L I F I E R S  
F R O M R I G H T A M P L I F I E R S  
RIGHT  
+
BLU/WHT  
Amplifier  
(Midrange)  
BLU/BLK  
To LEFT  
Woofer  
To RIGHT  
Woofer  
+
REFERENCE STANDARD AUTOMOTIVE  
LEFT  
Component System Crossover Network  
+HI  
BLU  
HI +  
TO LEFT  
TO LEFT  
TO RIGHT  
TO RIGHT  
BLU  
MIDRANGE  
TWEETER  
TWEETER  
MIDRANGE  
+
+
+
+
LO  
HI  
LO MID HI  
HI MID LO  
HI  
LO  
GRY/ RED/  
RED/ GRY/  
BLK  
BLK  
WHT  
WHT  
RIGHT  
GRY  
+HI  
RED  
RED  
GRY  
+
+HI  
Figure 7. After sliding down the flush-mount clip onto the  
back of the Kappa1.1cs EMIT-N tweeter, use the supplied  
hardware to fasten the cup to the panel.  
Amplifier  
(Woofers)  
To LEFT  
To RIGHT  
4"Midrange  
4"Midrange  
Figure 3.This application shows  
connections for a Kappa1cs sys-  
tem and three stereo amplifiers.  
+
+MID  
+MID  
LEFT  
To LEFT  
Tweeter  
To RIGHT  
Tweeter  
- 3 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A NOTE ON POWER HANDLING  
ADJUSTING THE SOUND  
SPECIFICATIONS  
The speakers used in Kappa Series 3-Way  
1.1cs  
Type:  
After you have connected all the speakers to the  
crossover according to the connection diagram,  
you may adjust the overall sound of the system to  
suit your taste.  
The output of the woofers may be decreased by  
moving the woofer + connection at the crossover  
to the low position.  
The output of the midrange may be decreased by  
moving the midrange + connection at the  
crossover to the low position.  
The output of the tweeter may be increased by  
moving the tweeter + connection at the crossover  
to the high position or decreased by moving it to  
the low position.  
653.1cs  
Type:  
Component Systems are designed to produce rea-  
sonable volume levels with little amplifier power.  
However, the addition of an amplifier to drive  
your speakers and a subwoofer will enhance the  
dynamic range of your system, and help over-  
come the ambient noise in a moving vehicle.  
Kappa speakers are designed to handle the power  
of a dedicated amplifier driven at or below its  
rated power. If an amplifier is driven far above its  
rated power, the output signal will “clip,” and the  
additional power present in a clipped signal can  
damage any speaker. Distorted or “fuzzy” sound  
from your speakers is an indication that the ampli-  
fier has exceeded its rated power, and you should  
reduce the volume level  
6" x 9" 3-Way System  
4 ohms  
200 watts per channel  
6-1/2" 3-Way System  
4 ohms  
120 watts per channel  
Speaker Impedance:  
Power Handling:  
Frequency  
Response (±3dB):  
Sensitivity:  
Speaker Impedance:  
Power Handling:  
Frequency  
Response (±3dB):  
Sensitivity:  
36Hz ~ 45kHz  
89Hz @ 2.83 V, 1 watt  
50Hz ~ 45kHz  
89Hz @ 2.83 V, 1 watt  
Crossover Frequencies: Woofer  
Hi terminal: 210Hz  
Crossover Frequencies: Woofer  
Hi terminal: 210Hz  
Lo terminal: 130Hz  
Midrange: 400Hz  
Tweeter:12.5kHz  
Lo terminal: 130Hz  
Midrange: 400Hz  
Tweeter: 12.5kHz  
Mounting Depth  
Drop-in Woofer:  
Cut-out  
Mounting Depth,  
Drop-in Woofer:  
Cut-out  
Diameter Woofer:  
Mounting Depth,  
Drop-in Midrange:  
Cut-out  
Diameter Midrange: 3-3/4" (96 mm)  
Mounting  
DepthTweeter:  
Cut-out  
DiameterTweeter:  
2-9/16" (65 mm)  
2-1/2" (67.5 mm)  
5-11/16" (149 mm)  
1-13/16" (46 mm)  
Diameter Woofer:  
5-11/16" x 8-3/4"  
(149 mm x 223 mm)  
Mounting Depth,  
Drop-in Midrange:  
Cut-out  
Diameter Midrange: 3-3/4" (96 mm)  
Mounting  
DepthTweeter:  
Cut-out  
DiameterTweeter:  
1-13/16" (46 mm)  
GENERAL CARE  
The loudspeaker grilles may be cleaned with a  
slightly damp cloth. Do not use any cleaners or  
solvents on the grilles or the speaker cones.  
1" (25.4 mm)  
1" (25.4 mm)  
3-3/8" x 1-3/4"  
(84.6 mm x 44.7 mm)  
3-3/8" x 1-3/4"  
(84.6 mm x 44.7 mm)  
DECLARATION OF CONFORMITY  
We, Infinity Systems A/S  
Kongevejen 194B  
DK-3460 Birkerød  
DENMARK  
declare in own responsibility, that the products described in this owner’s manual are in compliance with technical standards:  
EN 50 081-1/1992  
Steen Michaelsen  
Infinity Systems A/S  
EN 50 082-1/3.1995  
Birkerød. DENMARK. 2/98  
Infinity Systems, Inc. • 250 Crossways Park Drive,  
Woodbury, NY 11797 USA • (516) 496-3400 • FAX (516) 682-3583  
®
Download from Www.Somanuals.com. All Manuals Search And Download.  

Invacare Mobility Aid Electric wheelchair User Manual
IRiver MP3 Player IFP 800 User Manual
Jackson Dishwasher Conserver II User Manual
Jensen Car Stereo System CD4610 User Manual
JVC Speaker System HR A47U User Manual
Kenmore Vacuum Cleaner 11636722 User Manual
Kenwood Blender FP210 User Manual
Kicker Stereo Amplifier ZX3502 User Manual
KiSS Networked Entertainment DVD Player DP 450 User Manual
Kodak Digital Camera 1500628 User Manual