TSS-4000
TOTAL SPEAKER SOLUTIONS
TSS-CENTER1100
Owner’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Tilting the Speaker
WIRING THE SPEAKER
After placing the speaker, you are ready to connect it to your
system. First, turn off all audio system power. Use high-quality
speaker wire to make the connections. Consult the owner’s
manuals included with your amplifier or receiver for connection
and operation procedures.
If needed, the enclosed stand allows you to tilt the speaker
across a wide range (i.e., up a maximum of 18˚ or down a
maximum of 7˚), as shown in Figure 3.
Important!
Do not exceed the tilt range. Doing so may cause the speaker to
fall out of its stand.
Surround Modes
When using the TSS-CENTER1100 in a Dolby* Digital or DTS®
home theater system, make sure the amplifier or receiver
center channel speaker modes are set to“Small.”
Wiring and Polarity
The TSS-CENTER1100 speaker has gold-plated terminals that
can accept bare wire.To ensure proper polarity, connect each
+ terminal on the back of the amplifier or receiver to the
respective + (red) terminal on each speaker, as shown in
Figure 4. Connect the – (black) terminals in a similar way.
See the owner’s manuals that were included with your
amplifier or receiver to confirm connection procedures.
Important!
Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will degrade the imaging and bass
response of the home theater system.
After correctly placing and wiring the TSS-CENTER1100 and
the rest of your speaker system, adjust the levels for all of the
channels as recommended by the manufacturer of your amplifier
or receiver.
Figure 3.
ᕡ
ᕢ
–
+
Figure 4.This example shows how to connect bare wires to the
terminals. Banana plugs may also be inserted directly into the
rear of the connector.
ᕡ Loosen the terminals.
ᕢ Insert bare ends; tighten terminals.
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE OF YOUR SPEAKER SYSTEM
When needed, use a soft cloth to remove any fingerprints or
to wipe off dust. Do not use any cleaning products or polish.
Clean the grille by gently vacuuming.
SPECIFICATIONS
TSS-CENTER1100
Frequency Response
120Hz – 20kHz ( 3dB)
Nominal Impedance
8 ohms
89dB
Sensitivity
(2.83V @ 1m)
Recommended Amplifier
Power Range
10 – 125 watts
Crossover Frequencies
Low-Frequency Drivers
3,500Hz; 24dB/octave
(2) 3-1/2" (89mm) MMD®,
magnetically shielded
High-Frequency Driver
3/4" (19mm) MMD,
elliptical waveguide,
magnetically shielded
Dimensions (H x W x D)
Weight
4-1/8" x 9-1/4" x 4-3/8"
(105mm x 235mm x 111mm)
4.5 lb (2.0kg)
Infinity continually strives to update and improve existing products, as well as create new ones.
The specifications and construction details in this and related Infinity publications are therefore
subject to change without notice.
Declaration of Conformity
We, Harman Consumer Group International
2, route de Tours
72500 Chateau-du-Loir
France
declare in own responsibility that the product
described in this owner’s manual is in compliance
with technical standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
© 2005 Harman International Industries, Incorporated.All rights reserved.
Infinity Systems, 250 Crossways Park Drive,Woodbury, NY 11797 USA
*Trademark of Dolby Laboratories. DTS is a registered trademark of Digital Theater Systems, Inc.
Laurent Rault
Infinity and MMD are registered trademarks, and Total Solutions is a trademark, of
Harman International Industries, Incorporated.
Harman Consumer Group International
Chateau-du-Loir, France 5/05
Part No. 400-OMCNTR 5/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|