TSS-1100
6 – Piece Home Theater System
SERVICE MANUAL
Infinity Systems Incorporated
250 Crossways Park Dr.
Woodbury, New York 11797
Rev2 1/2006
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
TSS-1100 150W Powered Sub/ Plate Amp
LINE VOLTAGE
US 120vac/60Hz
EU 230vac/50-60Hz
Yes/No
Yes
Yes
Hi/Lo Line
108-132
207-264
Nom.
120
230
Unit
Notes
Vrms
Vrms
Normal Operation
Normal operation, MOMS required
QA Test
Limits
Parameter
Specification
Unit
Conditions
Notes
Amp Section
Type (Class AB, D, other)
Load Impedance (speaker)
Rated Output Power (120VAC
Rated Output Power (230VAC
D
5.6
150
150
Ohms
Watts
Watts
n/a
110
110
Nominal
Domestic version only 120 VAC-60 Hz
EU Version only
230 VAC-50 Hz
Average RMS power, 3/20 Cycles 50 Hz, Driven
6dB above its input sensitivity sensitivity
145 Watts
AVG RMS Dynamic Power
THD @ Rated Power
THD @ 1 Watt
250
0.5
0.1
Watts
%
%
225
1
0.5
30
22K filter
22K filter
Amplifier output
DC Offset
10 mV-DC
Measured at the amplifier board. 120 Watts @
50 Hz, THD must be less tan 0.1%
Damping factor
>50
DF
20
Measured at amplifier board
Input Sensitivity
Input Frequency
L&R
35
188
188
Hz
mVrms
mVrms
35
±2dB
±2dB
Nominal Freq.
To 110 Watts, Ap Zo=600 Ohms
To 110 Watts , Ap Zo=600 Ohms
Single input driven
L or R input
Single input driven, LFE switch ON
Single input driven, LP switch to Normal, This
applies to 230VAC model only
Speaker/Hi Level Input
1.68
Vrms
±2dB
To 120 Watts
Signal to Noise
SNR-A-Weighted
SNR-unweighted
SNR rel. 1W-unweighted
90
85
65
dBA
dBr
dBr
85
80
60
relative to rated power
relative to rated power
relative to 1W Output
A-Weighting filter
22K filter
22K filter
Volume @max, w/ A/P Swept
Bandpass Measurement (Line
freq.+ harmonics) (BW=20 Khz)
Line level inputs must be terminated using
1KOHM
Residual Noise Floor
1 mVrms(max)
1.5
Input Impedance
Line Input (L, R,LFE)
Speaker/Hi Level Input
10K
> 4.7K
ohms
ohms
n/a
n/a
Nominal
Nominal
Filters
LP filter 4th order fixed
HP Filter 2nd order
LFE Low pass 2nd order
Notch filter (Friend circuit)
HP speaker out connector
Left & Right
50-150 Hz
Fixed
200>LP<1K Hz
± 10
2nd Order variable and 2nd order fix 2nd order variable + 2nd order fix-24 db/Octave
LFE input driven only
F=61 Hz, Q=3.607, Av=-8.62dB
1st order fix
200 Hz
± 10
± 10
Speaker input - Spkr out 4 Ohms (Applies to 230VAC model only)
Speaker input - Spkr out 8 Ohms (Appies to 230VAC model only)
Left & Right
100 Hz
Limiter
THD at Max. Output Power
n/a
n/a
--
functional Maximum Output Power
Maximum THD as a result of limiting.
Features
Volume pot Taper (lin/log)
Speaker input connectors
--
LOG
YES
functional
functional
A Taper
L&R Speaker input binding post connectors
L&R Speaker out with HP applies only to
230VAC models
HP Speaker out
Phase switch
LP Filter defeat switch
YES
0-180
YES
functional
functional
functional
deg
Disables LP filter, intended for LFE
Input Configuration
functional
functional
Dual RCA jack
Line In (L,R) & LFE
YES
YES
--
--
Binding post connector L&R (Applies to
230VAC model only)
Spkr/Hi Level In
Signal Sensing (ATO)
Auto-Turn-On (yes/no)
ATO Input test frequency
ATO Level LFE Input
YES
50
2
functional
functional
functional
Hz
mV
Maximum acceptable level.
Maximum acceptable level. (Applies to 230VAC
model only)
ATO Level Speaker in
ATO Turn-on time
40
5
mV
ms
functional
Amp connected and AC on, then
functional input signal applied
T before muting, after line or
Auto turn of time (T) must be 5 > T < 18
Minutes
Auto Mute/ Turn-OFF Time
Power on Delay time
15 minutes
sec.
18
speaker level signal is removed
3
4
AC Power Applied
2
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
QA Test
Limits
Parameter
Specification
Unit
Conditions
Notes
Transients/Pops
ATO Transient
5
mV-peak
n/a
@ Speaker Outputs
Turn-on Transient
Turn-off Transient
50 mV-peak
50 mV-peak
2V-pk-pk @ Speaker Outputs
2V-pk-pk @ Speaker Outputs
AC Line cycled from OFF to ON
AC Line cycled from ON to OFF
Efficiency
Efficiency
65
%
65
Nominal Line voltage 120 VAC
Maximum allowable input power under nominal
Input voltage and frequency, HOT or COLD
operation.
Stand-by Input Power
Power Cons. @ rated power
Protections
18
Watts
Watts
20
@ nom. line voltage
@ nom. line voltage
170
180
120 Watts into 5.6 Ohms @ nominal line voltage
Amplifier should resume operation after short
circuit condition removal
Temperature rise in accessible metal parts
should not exceed 35K rise for domestic version
Short Circuit Protection
YES
YES
functional Direct short at output
@1/8 max unclipped Power at 1.06 or 30K rise for European versions (refer to
Thermal Protection
functional times the input voltage
requirements sheet).
Design must insure no Offset at the speaker
output under any operating condition including
abnormal operation
DC Offset Protection
Line Fuse Rating
USA-Domestic
YES
2
-
2
DC present at Speaker Out leads
Amps
Amps
Type-T or Slo Blo-250 V
Type-T or Slo Blo-250 V, Low
Breaking capacity
Internal fuse with UL/SEMKO rated holder
Internal fuse with UL/SEMKO rated holder
EU
1.25
1.25
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
S
UBWOOFER CONTROLS
ᕡ
ᕢ
ᕣ
ꢀ
ᕥ
ᕦ
Subwoofer-Level Control
LFE/Normal Switch
Rear Panel
Phase Switch
Crossover-Frequency Adjustment
Line-Level (LFE) Inputs
Power Switch
¡
LEVEL
Max
NORMAL
Min
LFE
™
0˚
180˚
PHASE
£
CROSSOVER
FREQUENCY
¢
150Hz
50Hz
A Few Suggestions
L
R
∞
We recommend that you do not operate your speakers or
subwoofer with the bass, treble and loudness controls set to
full boost.This will place undue strain on your electronics and
speakers and could damage them.
LINE LEVEL IN
For LFE use L or R
The volume control setting on your processor/preamp or receiver
is not a specific indication of the overall loudness level of the
speakers.The only important consideration is the loudness level at
which the system can be played, regardless of where the volume
control is set.
ON
OFF
§
POWER
Always turn down the volume control setting on your processor/
preamp or receiver when changing a cassette or CD, or switching
inputs to AM or FM operation. Excessively loud transients (clicks or
popping sounds) can damage the satellite speakers and possibly
the subwoofer.
®
Important!
CAUTION
Whenever changing cables, pulling plugs, etc.,ALWAYS TURN OFF
ALL EQUIPMENT, including the subwoofer.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
®
NRTL/ C
CSA22.2
UL1492
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
AVERTISSEMENT: POUR PRÉVENIR LES RISQUES D’INCENDIE OU
DE CHOC ÉLECTRIQUE, ÉVITER D’EXPOSER CET APPAREIL A LA
PLUIE OU A L’HUMIDITÉ.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
SUBWOOFER CONNECTIONS
®
If you have a Dolby* Digital or DTS receiver/
processor with a low-frequency-effects (LFE)
or subwoofer output:
If your receiver/processor does not contain
a Dolby Digital or DTS processor but has a
subwoofer output:
RECEIVER/PROCESSOR
SUBWOOFER OR
LFE OUTPUT
LEVEL
Max
Min
LFE
0º
NORMAL
180º
PHASE
LEVEL
80Hz
Max
NORMAL
Min
15'
subwoofer
cable
CROSSOVER
FREQUENCY
LFE
0º
150Hz
50Hz
180º
PHASE
80Hz
15' subwoofer
cable included
included
L
R
CROSSOVER
FREQUENCY
LINE LEVEL IN
150Hz
50Hz
For LFE use L or R
L
R
LINE LEVEL IN
Set line-level/LFE switch to“Normal.”
For LFE use L or R
NOTE: If your receiver/processor has only one sub out,
you may use either the L or R input.
Set line-level/LFE switch to“LFE.”
TSS-1100
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
OPERATION
Surround Modes
Crossover Adjustment
The Crossover Frequency Control ꢀ determines the highest
frequency at which the subwoofer reproduces sounds. For the
TSS-1100, it is recommended that this control be set at 120Hz
(approximately the 3 o’clock position).
When using the system in a Dolby Digital or DTS home theater
system, make sure all speakers are set to“Small”. When using the
TSS-1100 in a Dolby Pro Logic* home theater system, make sure
the receiver’s center channel mode is set to“Normal.”
Some Dolby Digital-equipped receivers/processors offer different
setup options for each source or surround mode, e.g., CD-stereo,
videotape, Dolby, Pro Logic. In each case, follow your equipment’s
instructions to ensure that the subwoofer output is turned on and
that the speakers are set to“Small”in each mode.
NOTE: This control will have no effect if the LFE/Normal Switch
ᕢ is set to LFE. If you have a Dolby Digital or DTS receiver/
processor, the Low-Pass Frequency is set by the receiver/
processor. Set the LFE/Normal Switch ᕢ on the subwoofer to
LFE. Consult your owner’s manual to learn how to view or change
this setting.A setting of 120Hz – 150Hz is recommended.
Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use the
outlets on the back of the receiver.
Phase Control
The Phase Switch ᕣ determines whether the subwoofer
speaker’s piston-like action moves in and out with the main
speakers, 0˚, or opposite the main speakers, 180˚. Proper phase
adjustment depends on several variables such as room size,
subwoofer placement and listener position.Adjust the phase
switch to maximize bass output at the listening position.
ᕡ
Initially set the Subwoofer Level Control to the“MIN”position.
ᕦ
Turn on the subwoofer by pressing the Power Switch on the
rear panel.
Turn on your entire audio system and start a CD or movie sound-
track at a moderate level.
Final Positioning
Auto On/Stand-By
After correctly connecting the TSS-1100 system and verifying
that both the subwoofer and all satellite speakers are playing, it
is time to optimize the system for your particular listening room.
Earlier, you placed the subwoofer in its general location. Finding
the exact location for optimum performance sometimes only
involves moving the speakers up to a few inches in any
ᕦ
With the Power Switch in the ON position, the LED on the front
panel will remain lit in red or green to indicate the On/Stand-By
mode of the subwoofer.
RED = STAND-BY (No signal detected,Amp Off)
GREEN = ON (Signal detected,Amp On)
direction.We urge you, therefore, to experiment with placement,
if possible, until your speakers deliver their full potential.
The subwoofer will automatically enter the Stand-By mode after
approximately 10 minutes when no signal is detected from your
system.The subwoofer will then power ON instantly when a signal
is detected. During periods of normal use, the Power Switch
can be left on.You may turn off the Power Switch for extended
periods of nonoperation, e.g., when you are away on vacation.
ᕦ
ᕦ
M
AINTENANCE AND SERVICE
The satellite and subwoofer enclosures may be cleaned using a
soft cloth to remove fingerprints or to wipe off dust.
Adjust Level
Turn the Subwoofer Level Control up about half way. If no
ᕡ
All wiring connections should be inspected and cleaned or
remade periodically.The frequency of maintenance depends on
the metals involved in the connections, atmospheric conditions,
and other factors, but once per year is the minimum.
sound emanates from the subwoofer, check the AC-line cord and
input cables.Are the connectors on the cables making proper
contact? Is the AC plug connected to a“live”receptacle? Has the
ᕦ
Power Switch been pressed to the“On”position? Once you
have confirmed that the subwoofer is active, proceed by playing a
CD or DVD. Use a selection that has ample bass information.
If a problem occurs, make sure that all connections are properly
made and clean. If a problem exists in one loudspeaker, reverse
the connection wires to the left and right system. If the problem
remains in the same speaker, then the fault is with the loud-
speaker. If the problem appears in the opposite speaker, the
cause is in another component or cable. In the event that your
TSS-1100 ever needs service, contact your local Infinity dealer
or Infinity directly at 516.674.4INF (USA only) or
Set the overall volume control of the receiver/processor to a
ᕡ
comfortable level.Adjust the Subwoofer Level Control until
you obtain a pleasing blend of bass. Bass response should
not overpower the room but rather be adjusted so there is
a harmonious blend across the entire musical range. Many
users have a tendency to set the subwoofer volume too loud,
adhering to the belief that a subwoofer is there to produce lots of
bass.This is not entirely true.A subwoofer is there to enhance
bass, extending the response of the entire system so the bass
can be felt as well as heard. However, overall balance must
be maintained or the music will not sound natural.An experienced
listener will set the volume of the subwoofer so its impact on
bass response is always there but never obtrusive.
www.infinitysystems.com for a service center near you.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
SERVICE NOTE
Access to woofer:
1) Carefully pry metal grille out of its recess with a sharp pointed
instrument such as an awl or dental pick – USE CAUTION and
protect the surface of the subwoofer from scratches or dents from
the work tool. Work evenly around the perimeter until the grill w/
gasket can be removed.
2) Remove the (6) Phillips screws holding the trim ring to the cabinet.
3) Remove the (6) Phillips screws holding the woofer to the cabinet.
REPLACEMENT: Assure when the woofer is replaced, it is exactly centered
in the counterbore.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
TSS-1100 Satellites/Center & Packing
PART #
DESCRIPTION
TSS-1100 system
1100-SATBPLT
1100-SATBCHR
1100-CENBPLT
1100-CENBCHR
1100-GSPLT
1100-GCPLT
1100-GSCHR
1100-GCCHR
1100-CRPLT
1100-CRCHR
1100CTN-PLT
1100CN-PLT230
1100CTN-CHR
1100CN-CHR230
1100SOM-120
1100SOM-230
1100WS-120
Complete TSS-1000 Satellite (Platinum)
Complete TSS-1000 Satellite (Charcoal)
Complete TSS-1000 Center channel (Platinum)
Complete TSS-1000 Center channel (Charcoal)
Grill cover w / logo for satellite TSS-1100 platinum
Grill cover w / logo for center TSS-1100 platinum
Grill cover w / logo for satellite TSS-1100 charcoal
Grill cover w / logo for center TSS-1100 charcoal
Cradle for center TSS-1100 platinum
Cradle for center TSS-1100 charcoal
Carton for TSS-1100 platinum 120V
Carton for TSS-1100 platinum 230V
Carton for TSS-1100 charcoal 120V
Carton for TSS-1100 charcoal 230V
120V Owner manual for TSS-1100
230V Owner manual for TSS-1100
TSS-1100 warranty sheet 120V
1100-SCTF1
Top styrofoam sat/center pack
1100-SCBF2
Bottom styrofoam sat/center pack
1100-WFT1
Top styrofoam subwoofer
1100-WFB2
Bottom styrofoam subwoofer
1100-BRTPLT
TSS-1100 wall mount bracket Platinum
TSS-1100 Satellite single pack
TSS-SAT1100PLT
TSS-SAT1100CHR
1100-BRTPLT
1100-BRTCHR
1100CTNSP-PLT
1100CTNSP-CHR
1100SATOM
Complete packed TSS-1000 Satellite (Platinum) w/ accessories
Complete packed TSS-1000 Satellite (Charcoal) w/ accessories
TSS-1100 wall mount bracket Platinum
TSS-1100 wall mount bracket Charcoal
TSS-1100 Sat single pack beauty carton -PLT
TSS-1100 Sat single pack master carton-CHR
TSS-1100 Sat OM
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
TSS1100 sub Test Set Up and Procedure
SYSTEM AURAL SWEEP TEST
Equipment needed:
• Function/signal generator/sweep generator
• Multimeter
• RCA cables
General Unit Function (UUT = Unit Under Test)
Switches/knobs on the amplifier faceplate:
Crossover Frequency Adjust full CW (150Hz)
Phase switch – either position
Normal/LFE switch - Normal
1. From the signal generator, Connect both right and left line level inputs (RCA jacks) – to signal generator and
UUT. Use Y-cable if necessary from mono source.
2. On the amplifier, turn the LEVEL control full Counterclockwise (Min).
3. Turn on generator, adjust to 150mV, 50 Hz.
4. Plug in UUT; turn the power switch ON. Turn LEVEL control full Clockwise (Max).
5. LED (on front panel) should now be Green; immediate bass response should be heard and felt from rear port
tube opening.
Sweep Function
1. Follow steps 1-5 above, using a sweep generator as a signal source.
2. Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofer and test.
Driver Function (Woofer)
1. Remove woofer from cabinet (follow steps on exploded view page); detach + and - wire clips.
2. Check DC resistance of woofer; it should be 3.3 ohms±10%.
3. Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated
amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
TSS-1100 120V ELECTRICAL PARTS LIST
Part Number
MAIN PCB
Resistors
Qty
Description
Reference Designator
020-000098-400
020-220497-120
021-100401-120
021-220202-120
021-240405-020
022-500003-020
024-100298-120
024-100398-120
024-100498-100
024-100498-120
4
1
1
1
4
1
2
1
1
7
Carbon film resistor 0R 1/8W
Carbon film resistor 2K2 1/4W J
MOF Resistor 1K 1W J Kink
MOF Resistor 22R 2W(S) J MB
MOF Resistor 2K4/5WS J 17x6
Resistor KNP 0R05 3WS J FK TYPE
SMD Resistor 10R 1/8W J 0805
SMD Resistor 100R 1/8W J 0805
SMD Resistor 1K 1/8W F 0805
SMD Resistor 1K 1/8W J 0805
C22-C24,31
R11
R103
R10
R6,9,R7A,R9A
R104
R81,82
R62
R110
R79,83,92,95,96,105,65
R2,17,19,37,54,58,63,71,72,74,75,84,88,89,97,106,113-
117,111,123,124, 119,120
R2-4
R3,112
R121
R2A
R98
R4A
R35A
R32
R6A
R39
R38
R29
R45
R108
R94
R90
024-100598-120
024-100598-120
024-100698-120
024-100898-120
024-110498-120
024-110598-100
024-110698-100
024-133598-100
024-137698-100
024-160398-120
024-162598-100
024-178498-100
024-180598-100
024-187698-100
024-200498-120
024-200598-120
024-220398-120
024-220498-121
024-220598-120
024-220798-120
024-237598-120
024-270498-120
024-280498-100
024-300398-120
024-300598-120
024-330498-120
024-330598-120
024-332498-100
024-390498-120
024-390598-120
024-430498-120
024-453498-100
024-453598-100
024-470298-120
024-470398-120
024-470498-120
024-470598-120
024-470698-120
024-470798-120
024-510398-120
024-560498-120
024-560598-120
024-620398-100
024-680398-120
024-680498-120
024-680598-120
024-820598-120
025-010300-000
26 SMD Resistor 10K 1/8W J 0805
3
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
2
2
1
1
8
2
2
1
1
1
1
1
2
3
2
4
1
1
1
1
1
2
1
6
6
1
1
SMD Resistor 10K 1/8W J 0805
SMD Resistor 100K 1/8W J 0805
SMD Resistor 10M 1/8W J 0805
SMD Resistor 1K1 1/8W J 0805
SMD Resistor 11K 1/8W F 0805
SMD Resistor 110K 1/8W F 0805
SMD Resistor 13K3 1/8W F 0805
SMD Resistor 137K 1/8W F 0805
SMD Resistor 160R 1/8W J 0805
SMD Resistor 16K2 1/8W F 0805
SMD Resistor 1K78 1/8W F 0805
SMD Resistor 18K 1/8W F 0805
SMD Resistor 187K 1/8W F 0805
SMD Resistor 2K 1/8W J 0805
SMD Resistor 20K 1/8W J 0805
SMD Resistor 220R 1/8W J 0805
SMD Resistor 2K2 1/8W J 0805
SMD Resistor 22K 1/8W J 0805
SMD Resistor 2M2 1/8W J 0805
SMD Resistor 23K7 1/8W F 0805
SMD Resistor 2K7 1/8W J 0805
SMD Resistor 2K8 1/8W F 0805
SMD Resistor 300R 1/8W J 0805
SMD Resistor 30K 1/8W J 0805
SMD Resistor 3K3 1/8W J 0805
SMD Resistor 33K 1/8W J 0805
SMD Resistor 3K32 1/8W F 0805
SMD Resistor 3K9 1/8W J 0805
SMD Resistor 39K 1/8W J 0805
SMD Resistor 4K3 1/8W J 0805
SMD Resistor 4K53 1/8W F 0805
SMD Resistor 45K3 1/8W F 0805
SMD Resistor 47R 1/8W J 0805
SMD Resistor 470R 1/8W J 0805
SMD Resistor 4K7 1/8W J 0805
SMD Resistor 47K 1/8W J 0805
SMD Resistor 470K 1/8W J 0805
SMD Resistor 4M7 1/8W J 0805
SMD Resistor 510R 1/8W J 0805
SMD Resistor 5K6 1/8W J 0805
SMD Resistor 56K 1/8W J 0805
SMD Resistor 620R 1/8W F 0805
SMD Resistor 680R 1/8W J 0805
SMD Resistor 6K8 1/8W J 0805
SMD Resistor 68K 1/8W J 0805
SMD Resistor 82K 1/8W J 0805
Thermister TSE-103 K L:50mm
R1,87,61,68
R118
R80
R48
R73,64
R51,53
R55
R56
R7,8,12-15,59,67
R4,5
R26,27
R93
R77
R78
R36
R30
R101,102
R76,99,100
R85,86
R44,47,49,107
R70
R60
R57
R1
R122
R16,18
R5A
R46,91,40-43
R33,34A,31,50,52,66
R69
TH1
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
MAIN PCB
026-200595-269
026-500495-252
1
1
VR PN:RD163121R03D-20KBx2(EJ) FREQUENCY
VR 5KA PN:RK163111R52B-5KA (EJ) LEVEL
VR2
VR1
Capacitors
031-100144-103A
031-100184-100A
031-100244-100A
031-100343-100A
031-100344-100
031-100344-100A
031-220243-103
031-220344-300A
031-330444-300
031-470244-102A
031-470344-100A
031-560243-100A
031-820343-101A
032-100484-200
032-270393-300
032-820244-200
033-470464-270
033-680464-270
034-100525-300
034-100625-300
034-220525-301
034-330515-000
034-330525-300
034-330615-300
034-330780-300
034-470415-301
034-470515-200
034-470615-301
035-100393-301
035-100443-300
035-220393-300
035-470293-300
038-100363-300
039-100384-100
1
2
7
2
4
SMD Capacitor 0u001/50V K 0805 X7R TAP
SMD Capacitor 0u01/250V K 0805 X7R TAP
SMD Ceramic capacitor 0u01/50V K 0805 X7R
SMD Capacitor 100pF/50V J 0805 NPO TAP
SMD Capacitor 0u1/50V K 0805 X7R TAPIN
C79
C3,7
66,67,5,10,33,45,51,
C36,58)
C1-4
C11,42-44,46-49,52,54,55,60,63,71,74,77
C40
C20,21,19
C34
C62,59
C80
C57,61
C56
C70,C70B
C29
C30
C73
C72
C35
C64
C4,9,41,50,53
C39
16 SMD Capacitor 0u1/50V K 0805 X7R TAPIN
1
3
1
2
1
2
1
2
1
1
1
1
1
1
5
1
1
2
2
1
1
1
2
2
1
1
2
1
SMD Capacitor (PHYCOMP) 0u022/50V J 080
SMD Capacitor 220pF/50V K 0805 NPO TAP
SMD Capacitor 3300pF/50V K 0805 X7R TA
SMD Capacitor 0u047/50V K 0805 X7R TAP
SMD Capacitor 470pF/50V K 0805 X7R TAP
SMD Capacitor 56pF/50V J 0805 NPO TAPI
SMD Capacitor 820pF/50V J 0805 NPO TAP
END Mylar capacitor 1uF/250V K P:15
Mylar capacitor (ESK) 0u27/63V J (R) P:5
Mylar capacitor 0u082/100V K (R)
NPE Capacitor 1K 4u7/100V K1
NPE Capacitor 6u8/100V K10
Electrolytic capacitor 10uF/25V M (R)0511 P:5
Electrolytic capacitor 100uF/25V M (R)6
Electrolytic capacitor 22uF/25V M (R)5x11 P:5
Electrolytic capacitor 33uF/16V M (R)0511 P:5
Electrolytic capacitor 33uF/25V M (R)05
Electrolytic capacitor 330uF/16V M (R)0812 P:5
Electrolytic capacitor 85 SNAPIN 3300uF/80V
Electrolytic capacitor 4u7/50V M (R)0511 P:5 T
Electrolytic capacitor 47uF/16V M (R)0511 P:2.
Electrolytic capacitor 470uF/16V M (R)0812 P:5
Mylar capacitor (ESK TYPE) 0u1/63
C1
C12,78
C6,8
C2
C37
C65
C28,2A
C25,26
C27
C1A
C68,69
CXAC1
Mylar capacitor (ESK TYPE) 1uF/63
PE Capacitor 0u22/63V J P:5
PE Capacitor 0u047/63V J P:5
MPE capacitor P:5 0u1/100V J
Safety capacitor (0u1/250V) PN:HQX0.1K27
Semiconductors
051-000600-100
051-003100-000
051-005600-100
051-222200-100
051-290700-100
051-540101-000
051-555100-000
051-640001-000
052-400080-000
053-211100-000
054-000100-100
054-001002-100
054-001501-100
054-007200-100
054-007400-100
054-008403-100
054-011400-100
054-033904-100
054-033906-100
054-045580-100
054-050601-100
054-390402-100
054-414803-100
054-414803-100
2
1
1
1
2
1
1
2
1
1
5
1
3
2
2
1
1
7
4
1
2
1
Transistor NPN PN:MPSW06RLRA TO-92 T
Transistor NPN PN:TIP 31C TO-220 (MO
Transistor PNP PN:MPSW56RLRA TO-92 T
Transistor NPN (ON SEM) PN:MPS2222AR
Transistor PNP (ON) PN:MPS2907A RLRA
Transistor PNP(FAIRCHILD PN:2N5401 T
Transistor NPN PN:2N5551 TO-92 TAPIN
MOSFET N-Channel PN:IRF640N TO-2
Bridge Rectifier PN:RS804 400V,8A
Q2,Q16
Q4
Q3
Q21
Q19,23
Q1
Q17
Q18,22
BR1
U7
D5,26,29,33,38
D35
D6,7,9
U1,5,6
U2,3
D25
IC, IR2111 HALF-BRIDGE DRIVER
SMD DIODE PN:ES1D 200V 1A
SMD ZENER DIODE PN:BZX84C10 10V
SMD ZENER DIODE PN:BZX84C15 15V
SMD IC PN:TL072CDR SO-8 DUAL OP-AMP
SMD IC PN:TL074CDR QUAD OP-AMP
SMD ZENER DIODE BZX84C3V0 SOT-23
SMD Transistor PN:DTC114TKA SMT3 TAP
SMD Transistor PN:MMBT3904LT1 SOT23
SMD Transistor PN:MMBT3906LT1 SOT23
SMD IC NJM4558M-TE3 DUAL OP-AMP
SMD ZENER DIODE PN:BZX84C5V6 5.6
SMD Transistor (SC00044) PN:MMBT3904TR
Q7
Q11,14,13,5,8,25,9
Q6,10,12,15
U4
D36,37
Q1
D1-4,8,27,30,31,34,39, 11,14,16,17, 20-22,18,19,28,32
D1,2
21 SMD DIODE PN:LL4148
SMD DIODE PN:LL4148
2
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
MAIN PCB
054-540100-100
3
SMD Transistor (PNP) PN:MMBT5401 LT1
Q20,24,26
THERMAL SENSE PCB
024-100598-120
024-560498-120
031-100344-100
054-007200-100
054-390402-100
054-414803-100
3
1
4
1
1
2
SMD Resistor 10K 1/8W J 0805
SMD Resistor 5K6 1/8W J 0805
0U1/50V K 0805 X7R
SMD IC TL072CDR SO-8
SMD Transistor MMBT3904TR Fairchild
SMD Diode LL4148 Vishay
R138-R141
R140
C81-82, C13,C38
U8
Q27
D44-45
Miscellaneous
1100-LED
1
1
1
1
1
1
2
2
2
4
3
4
1
1
5
1
2
1
2
1
2
1
1
1
1
1
1
1
6
6
1
LED ass'y
042-010147-000
043-300101-000
043-324300-000
043-560200-000
043-840100-000
044-100100-000
061-020000-000
061-314002-000
061-400014-000
061-700044-000
063-010012-000
063-321102-000
063-531808-000
066-120300-900
072-010007-000
073-011001-400
073-032315-601
073-050001-000
074-020018-000
074-030002-000
074-300018-000
083-041802-009
093-105202-300
008-061215-000
008-062002-002
008-062002-012
008-062004-012
008-063208-000
008-069304-000
041-115001-000
Transformer PN:YT-15250 (TSS1100/120V
INDUCTOR PN:YT-10033 30uH
INDUCTOR 324uH YT-10778
L2
L4
L1
L3
INDUCTOR 56uH YT-10779
Inductor PN:YT-14389 84uH TSS1100/23
SMD FERRITE BEAD PN:321611 600R/
Knob ABS HTS-10/20 φ20x15m/m UL
Strain Relief P/N SB4F-2
RUBBER FOOT ID:6.2 OD:11.5 t=2mm
Mica 13x18mm TO-220 holeless
Bracket for power transistor P/N:TRK-1
PANEL (ARMANDO) 322x105.7x15mm A
Bucket (PB-10/12) ABS 322x105.7x14
CABLE TIE CV-120S
RCA base SCJ-1020 2P(G) WHT,RED
BRACKET 16x34mm t=0.8mm brass plated
Heatsink, black anodized 70x58x20mm, thread
FUSE CLIP P/N:CFFH1206
ROCKER SW (POWER) PN:RF1003-BB4-0
TOGGLE SW PN:L101-T2B4QE
RELAY PN:943-1C-48D
UL Power Cord SPT-2 BLK 6 feet
FUSE:UL GSL(2AG) FUSE:2A,250V,5*
GASKET C4305 12x15 t=5mm CR PSA
GASKET (PB10/12) PN:L-32 200x20m
GASKET (PB10/12) 200x20mm t=2mm CR4305 PSA
GASKET 200x35x3mm PSA
GASKET C4305 321x8 t=1mm CR PSA
GASKET C4305 93x4 t=1mm CR {SA
BEAD COIL YT-10911
FB1,FB2
94V-0 BLK
55degree BLK
Q4,18,22
for ICx4
BS-94VO BLK
6.5mm BLK (94VO)
CONN1
for PANEL
SW5,SW6
K1
F1
for Thermister
for Cover
for spkr cable
for Cover
for Cover
L5
230V VARIATION
086-021818-030
093-205201-320
042-010148-000
072-060170-000
072-060213-000
072-060214-000
1
1
1
4
4
4
VDE Power Cord LF2-75
Fuse 1.25A/250V VBS UTE
Power Transformer
Binding Post
Binding Post Plug (Black)
Binding Post Plug (Red)
F1
PT1
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
THERMAL SENSE PCB
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
Circled area =THERMAL SENSE PCB
N/U = Not Used
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TSS-1100
23
Download from Www.Somanuals.com. All Manuals Search And Download.
|