Instructions for use
WASHING MACHINE
Contents
GB
Installation, 2-3
Unpacking and levelling
Electric and water connections
The first wash cycle
GB
English,1
Technical details
Washing machine description, 4-5
Control panel
Leds
Starting and Programmes, 6
Briefly: how to start a programme
Programme table
Personalisations, 7
Setting the temperature
Setting the spin speed
Functions
WIL 85
Detergents and laundry, 8
Detergent dispenser
Bleach cycle
Preparing your laundry
Special items
Precautions and advice, 9
General safety
Disposal
Saving energy and respecting the environment
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning your appliance
Cleaning the detergent dispenser
Caring for your appliance door and drum
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
Before calling for Assistance
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the drain hose
! Do not use extensions or multiple sockets.
GB
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
! The power supply cable must never be bent or
dangerously compressed.
! The power supply cable must only be replaced by
an authorised serviceman.
65 - 100 cm
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
alternatively, place it
over the edge of a
basin, sink or tub,
fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
! We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Technical details
Model
WIL 85
Electric connection
59.5 cm wide
85 cm high
Dimensions
Capacity
Before plugging the appliance into the mains
socket, make sure that:
52.5 cm deep
• the socket is earthed and in compliance with the
applicable law;
from 1 to 5 kg
Electric
please refer to the technical data plate
fixed to the machine
• the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (on the right);
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres
Water
connections
• the supply voltage is included within the values i
ndicated on the Technical details table
(on the right);
Spin speed
up to 800 rpm
Control
programmes
according to
EN 60456
directive
• the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
programme 2; temperature 60°C;
run with a load of 5 kg.
This appliance is compliant with the
following European Community
Directives:
! The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments
- 2002/96/CE
! When the washing machine is installed, the mains
- 2006/95/CE (Low Voltage)
socket must be within easy reach.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing machine description
Control panel
FUNCTION
Buttons
GB
Leds
ON-OFF/
DOOR
LOCK
Led
ON-OFF
Button
PROGRAMME
Knob
Detergent dispenser
START/RESET
Button
TEMPERATURE
Knob
SPIN SPEED
Knob
Detergent dispenser: to add detergent and fabric
softener (see page 8).
TEMPERATURE knob: to set the temperature or
the cold wash cycle (see page 7).
LEDS: to find out which wash cycle phase is under
START/RESET button: to start the programmes or
way.
cancel any incorrect settings.
If the Delay Timer function has been set, the time
left until the programme starts will be indicated (see
page 5).
ON-OFF/DOOR LOCK Led: to find out whether the
washing machine is on and if the appliance door can
be opened (see page 5).
SPIN SPEED knob: to set the spin speed or exclude
the spin cycle completely (see page 7).
ON/OFF button: to turn the washing machine on
and off.
FUNCTION buttons: to select the functions
available. The button corresponding to the function
selected will remain on.
PROGRAMME knob: to select the wash
programmes. The knob stays still during the cycle.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Leds
Cycle phase under way:
During the wash cycle, the LEDs gradually illuminate
on to indicate the cycle phase under way:
GB
The LEDS provide important information.
This is what they can tell you:
Prewash
Wash
Delay set:
If the Delay Timer function has been enabled (see
page. 7), once you have started the programme,
the LED corresponding to the delay set will begin to
flash:
Rinse
Spin cycle
Note: during draining, the LED corresponding to the
Spin cycle phase will be turned on.
Function buttons
The FUNCTION BUTTONS also act like LEDS.
When a function is selected, the corresponding
button is illuminated.
As time passes, the remaining delay will be
displayed, and the corresponding LED will flash:
If the function selected is incompatible with the
programme set, the button will flash and the
function will not be enabled.
If you set a function that is incompatible with
another function you selected previously, only the
last one selected will be enabled.
Once the set delay is complete, the flashing LED will
turn off and the programme set will start.
ON-OFF/DOOR LOCK led
If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any
damages, wait for the LED to flash before you open the appliance door.
! The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED
indicates there is an abnormality (see page 11).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting and Programmes
6. Add the detergent and any fabric softener
(see page 8).
7. Start he programme by pressing the START/RESET
button.
Briefly: starting a programme
GB
1. Switch the washing machine on by pressing button
All the LEDS will light up for a few seconds and
the ON-OFF/DOOR LOCK Led will begin to flash.
2. Load your laundry into the washing machine and
shut the appliance door.
3. Set the PROGRAMME knob to the programme
required.
4. Set the wash temperature (see page 7).
5. Set the spin speed (see page 7).
.
To cancel it, keep the START/RESET button pressed
for at least 2 seconds.
8. When the programme is finished, the ON-OFF/
DOOR LOCK Led will flash to indicate that the
appliance door can be opened. Take out your
laundry and leave the appliance door ajar to allow
the drum to dry thoroughly. Turn the washing
machine off by pressing button
.
Programme table
C ycle
length
(m inutes)
D etergent
Type of fabric and
degree of soil
Te m p e -
rature
Fabric Stain rem oval
softener option/bleach
Program m es
D escription of wash cycle
pre-
wash
wash
Standard
Cotton: Extremely soiled whites
(sheets, tablecloths, etc.)
Pre-wash, wash cycle, rinse cycles,
intermediate and final spin cycles
1
2
2
2
167
152
158
143
90°C
90°C
60°C
40°C
•
•
•
•
•
•
Cotton: Extremely soiled whites
(sheets, tablecloths, etc.)
Delicate/
Traditional
Wash cycle, rinse cycles,
intermediate and final spin cycles
•
Cotton: Heavily soiled whites
and fast colours
Delicate/
Traditional
Wash cycle, rinse cycles,
intermediate and final spin cycles
•
Cotton: Heavily soiled whites
and delicate colours
Delicate/
Traditional
Wash cycle, rinse cycles,
intermediate and final spin cycles
•
Cotton: Slightly soiled whites
and delicate colours (shirts,
jumpers, etc.)
Delicate/
Traditional
Wash cycle, rinse cycles,
intermediate and final spin cycles
3
99
40°C
•
•
Synthetics: Heavily soiled fast
colours (baby linen, etc.)
Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
4
4
5
6
7
60°C
40°C
40°C
40°C
30°C
•
•
•
•
•
•
•
•
•
•
Delicate
Delicate
Delicate
80
71
71
50
52
Synthetics: Heavily soiled fast
colours (baby linen, etc.)
Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Synthetics: Delicate colours (all
types of slightly soiled garments)
Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Wash cycle, rinse cycles and
delicate spin cycle
W ool
Very delicate fabrics
(curtains, silk, viscose, etc.)
Wash cycle, rinse cycles, anti-
crease or draining cycle
Time 4 you
Cotton: Heavily soiled whites
and fast colours
Wash cycle, rinse cycles,
intermediate and final spin cycles
8
9
60
50
60°C
40°C
•
•
•
•
Cotton: Slightly soiled whites
and delicate colours (shirts,
jumpers, etc.)
Wash cycle, rinse cycles,
intermediate and final spin cycles
Synthetics: Delicate colours (all
types of slightly soiled garments)
Wash cycle, rinse cycles,
delicate spin cycle
10
11
40°C
30°C
•
•
•
•
40
Synthetics: Delicate colours (all
types of slightly soiled garments)
Wash cycle, rinse cycles and
delicate spin cycle
30
Sport
Cold wash (without detergents),
wash cycle, rinse cycles, and
delicate spin cycle
12
13
°C
Sports shoes (MAX. 2 pairs)
30
•
•
•
•
50
63
Fabrics for sportswear
(Tracksuits, shorts, etc.)
Wash cycle, rinse cycles,
intermediate and final spin cycles
30°C
PARTIAL PROGRAMMES
Delicate/
Traditional
Rinse
•
Rinse cycles and spin cycle
Draining and spin cycle
Draining
Spin cycle
Drain
Notes
-For programmes 8 and 9, we advise against exceeding a wash load of 3.5 kg.
-For programme 13 we advise against exceeding a wash load of 2 kg.
-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.
Special programme
Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts
30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30°C), you can wash
different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Personalisations
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6).
GB
The temperature can be lowered, or even set to a cold wash ( ).
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the programme selected.
The maximum spin speeds for each programme are as follows:
Programmes
Cottone
Synthetics
Wool
Maximum spin speed
800 rpm
800 rpm
600 rpm
no
Silk
The spin speed can be lowered, or the spin cycle can be excluded altogether by selecting symbol
.
The washing machine will automatically prevent you from selecting a spin speed higher than the maximum speed
for each programme.
Note: to avoid excessive vibrations, before every spin cycle the machine distributes the load in a uniform manner by
continuously rotating the drum at a speed which is slightly faster than the normal washing speed.
When, despite repeated attempts, the load is still not evenly distributed, the machine spins at a lower speed than
the set frequency.
If the load is excessively unbalanced, the machine attempts to distribute it instead of spinning.
The balancing attempts may extend the total duration of the cycle, up to a maximum of 10 minutes.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
Enabled with
programmes:
Function
Effect
Comments
Press the button repeatedly until the LED corresponding to the
desired delay is turned on.
The fifth time the button is pressed, the function will be disabled.
N.B.: Once you have pressed the Start/Reset button, the delay
can only be decreased if you wish to modify it.
Delays the start
of the wash by
up to 9 hours.
All
Delay Timer
Bleaching cycle
designed to
remove the
Please remember to pour the bleach into extra compartment 4
(see page 8).
This function is incompatible with the EASY IRON function.
2, 3, 4, 5,
Rinse cycle.
Stain
removal
toughest stains.
This option
reduces the
amount of
creasing on
fabrics, making
them easier to
iron.
When this function is set, programmes 4, 5, 7 will end with the
laundry left to soak (Anti-crease) and the Rinse cycle phase
3, 4, 5, 7, 8,
9, 10, Rinse
cycle.
LED
- to conclude the cycle, press the START/RESET button;
- to run the draining cycle alone, set the knob to the relative
symbol and press the START/RESET button.
will flash.
Easy iron
This function is incompatible with the STAIN REMOVAL function.
1, 2, 3, 4, 5,
8, 9, 10, 12,
13, Rinse
cycle.
Increases the
efficiency of the
rinse.
Recommended when the appliance has a full load or with large
quantities of detergent.
Extra Rinse
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergents and laundry
Detergent dispenser
Preparing your laundry
GB
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your
• Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
appliance and even pollute the environment.
• Empty all pockets and check for loose buttons.
• Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 5 kg
Open up the detergent
dispenser and pour in
4
the detergent and fabric
Synthetic fabrics: max 2.5 kg
softener, as follows.
Delicate fabrics: max 2 kg
Wool: max 1 kg
3
2
1
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
compartment 1: Detergent for pre-wash
(powder)
Before pouring in the detergent, make sure that
extra compartment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Special items
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme 7
which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1 kg.
Liquid detergent should only be poured in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
extra compartment 4: Bleach
! Do not use hand wash detergent because it may
form too much foam.
Bleach cycle
! Traditional bleach should be used on sturdy
white fabrics, and delicate bleach for coloured
fabrics, synthetics and for wool.
Place extra
compartment 4,
provided, into
compartment 1.
When pouring in the
bleach, be careful not to
exceed the "max" level
indicated on the central
pivot (see figure).
To run the bleach cycle alone, pour the bleach into
extra compartment 4, set the Rinse programme
and enable the Stain removal option (see page 7).
To bleach during a wash cycle, pour in the detergent
and fabric softener, set the desired programme and
enable the Stain removal option (see page 7).
The use of extra compartment 4 excludes the
possibility of using the pre-wash cycle.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and advice
! The washing machine was designed and built in
compliance with the applicable international safety
regulations. The following information is provided for
your safety and should consequently be read carefully.
the impact on human health and the environment.
GB
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
General safety
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
• This appliance has been designed for non-
professional, household use and its functions must
not be changed.
Saving energy and respecting the
environment
• This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
Environmentally-friendly technology
• Never touch the washing machine when barefoot
or with wet or damp hands or feet.
If you only see a little water through your appliance
door, this is because thanks to the latest Indesit
technology, your washing machine only needs less
than half the amount of water to get the best results:
an objective reached to respect the environment.
• Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
• Do not open the detergent dispenser while the
appliance is in operation.
Saving on detergent, water, energy and time
• To avoid wasting resources, the washing machine
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
• Do not touch the drain water as it could reach
very high temperatures.
• Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
• The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
• In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
• Treating stains with a stain remover or leaving them
to soak before washing will cut down the need to
wash them at high temperatures. A programme at
60°C instead of 90°C or one at 40°C instead of
60°C will save up to 50% on energy.
• Always keep children well away from the
appliance while in operation.
• The appliance door tends to get quite hot during
the wash cycle.
• Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
• Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
• Before loading your laundry into the washing
machine, make sure the drum is empty.
• If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
The Delay Timer option (see page 7) helps to
organise your wash cycles accordingly.
Disposal
• Disposing of the packaging material:
observe local regulations, so the packaging can
be re-used.
• The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
• If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
Cutting off the water or electricity
supply
Cleaning the pump
GB
The washing machine is fitted with a self-cleaning
pump that does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber that protects the
pump, situated in the lower part of the same.
•
Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
•
Unplug your appliance when cleaning it and
during all maintenance operations.
! Make sure the wash cycle has ended and unplug
the appliance.
Cleaning your appliance
To access the pre-chamber:
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
1. using a screwdriver,
remove the cover panel
on the lower front of the
washing machine (see
figure);
Cleaning the detergent dispenser
Remove the dispenser
by pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
2. unscrew the lid
rotating it anti-
clockwise (see figure): a
little water may trickle
out. This is perfectly
normal;
Caring for your appliance door and
drum
•
Always leave the appliance door ajar to prevent
unpleasant odours from forming.
3. clean the interior thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong and
a cracked hose could easily split open.
! Never use hoses that have already been used.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem
GB
can't easily be solved by consulting the following list.
Possible causes/Solution:
Problem
• The appliance is not plugged into the socket, or not enough to
make contact.
The washing machine won't
start.
• There has been a power failure.
• The appliance door is not shut properly.
The wash cycle won't start.
• The
button has not been pressed.
• The START/RESET button has not been pressed.
• The water tap is not turned on.
• A delayed start has been set (using the Delay Timer, see page 7).
• The water inlet hose is not connected to the tap.
• The hose is bent.
The washing machine fails to
load water.
• The water tap is not turned on.
• There is a water shortage.
• The water pressure is insufficient.
• The START/RESET button has not been pressed.
• The drain hose is not fitted between 65 and 100 cm from the floor
(see page 3).
The washing machine
continuously loads and unloads
water.
• The free end of the hose is underwater (see page 3).
• The wall drainage system doesn't have a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and call for Assistance. If the dwelling is on one of
the upper floors of a building, there may be drain trap problems causing the
washing machine to load and unload water continuously. In order to avoid
such an inconvenience, special anti-drain trap valves are available in shops.
• The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 6).
• The Easy iron option is enabled: to complete the programme, press
the START/RESET button (see page 7).
The washing machine does not
drain or spin.
• The drain hose is bent (see page 3).
• The drain duct is clogged.
• The drum was not unblocked correctly during installation (see page 2).
• The washing machine is not level (see page 2).
• The washing machine is closed in between furniture cabinets and
the wall (see page 2).
The washing machine vibrates
too much during the spin cycle.
• The water inlet hose is not screwed on correctly (see page 2).
• The detergent dispenser is obstructed (to clean it, see page 10).
• The drain hose is not secured properly (see page 3).
The washing machine leaks.
• Switch off the machine and unplug the appliance; wait for
approximately 1 minute then switch it on again.
If the problem persists, contact Assistance.
The ON-OFF/DOOR LOCK Led
flashes rapidly at the same
time as at least one other LED.
• The detergent is not suitable for machine washing (it should bear
the definition "for washing machines" or "hand and machine wash",
or the like).
There is too much foam.
• You used too much detergent.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
195071498.00
-
05/2008
Xerox Business Services
Before calling for Assistance:
• Check whether you can solve the problem on your own (see page 11);
• Restart the programme to check whether the problem has been solved;
GB
• If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
! Always request the assistance of authorised servicemen.
Notify the operator of:
• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N).
This information can be found on the data plate situated on the rear of the washing machine.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|