Instructions for use
WASHER-DRYER
Contents
GB
Installation, 2-3
Unpacking and levelling, 2
GB
Electric and water connections, 2-3
The first wash cycle, 3
English,1
Technical details, 3
Washer-dryer description, 4-5
Control panel, 4
Leds, 5
Starting and Programmes, 6
Briefly: how to start a programme, 6
Programme table, 6
Personalisations, 7
Setting the temperature, 7
Setting the drying cycle, 7
Functions, 7
WIDL 106
Detergents and laundry, 8
Detergent dispenser, 8
Preparing your laundry, 8
Special items, 8
Precautions and advice, 9
General safety, 9
Disposal, 9
Saving energy and respecting the environment, 9
Care and maintenance, 10
Cutting off the water or electricity supply, 10
Cleaning your appliance, 10
Cleaning the detergent dispenser, 10
Caring for your appliance door and drum, 10
Cleaning the pump, 10
Checking the water inlet hose, 10
Troubleshooting, 11
Service, 12
Before calling for Assistance, 12
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the drain hose
! Do not use extensions or multiple sockets.
GB
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
! The power supply cable must never be bent or
dangerously compressed.
! The power supply cable must only be replaced by
an authorised serviceman.
65 - 100 cm
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
alternatively, place it
over the edge of a
basin, sink or tub,
fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
Technical details
! We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Model
WIDL 106
59.5 cm wide
85 cm high
Dimensions
Capacity
Electric connection
53.5 cm deep
from 1 to 5 kg for the wash programme;
from 1 to 4 kg for the drying programme
Before plugging the appliance into the mains
socket, make sure that:
Electric
voltage 230/240 Volts 50 Hz
• the socket is earthed and in compliance with the
applicable law;
connections
maximum absorbed power 2050 W
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres
Water
• the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (on the right);
connections
Spin speed
up to 1000 rpm
• the supply voltage is included within the values i
ndicated on the Technical details table
(on the right);
Wash: programme 2; temperature 60°C;
run with a load of 5 kg.
Control
Drying: first drying cycle performed with
a 1 kg load, by selecting a drying time
of 40 min;
programmes
according to
IEC456 directive
• the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
Second drying cycle performed with a 4
kg load and the DRYING knob on
the
setting.
This appliance is compliant with the
following European Community
Directives:
! The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
- 73/23/CEE of 19/02/73 (Low
Voltage) and subsequent amendments
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments
! When the washing machine is installed, the mains
socket must be within easy reach.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Washer-dryer description
Control panel
FUNCTION
Buttons
GB
Leds
ON-OFF/
DOOR
LOCK
Led
ON-OFF
Button
PROGRAMME
Knob
Detergent dispenser
START/RESET
Button
TEMPERATURE
Knob
DRYING
Knob
Detergent dispenser: to add detergent and fabric
softener (see page 8).
TEMPERATURE knob: to set the temperature or
the cold wash cycle (see page 7).
LEDS: to find out which wash cycle phase is under
START/RESET button: to start the programmes or
way.
cancel any incorrect settings.
If the Delay Timer function has been set, the time
left until the programme starts will be indicated (see
page 5).
ON-OFF/DOOR LOCK Led: to find out whether the
Washer-dryer is on and if the appliance door can be
opened (see page 5).
DRYING knob: to set the desired drying cycle
(see page 7).
ON/OFF button: to turn the Washer-dryer on and off.
FUNCTION buttons: to select the functions
available. The button corresponding to the function
selected will remain on.
PROGRAMME knob: to select the wash
programmes. The knob stays still during the cycle.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Leds
Cycle phase under way:
During the wash cycle, the LEDs gradually illumina-
te on to indicate the cycle phase under way:
GB
The LEDS provide important information.
This is what they can tell you:
Prewash / Wash
Rinse
Delay set:
If the Delay Timer function has been enabled (see
page. 7), once you have started the programme,
the LED corresponding to the delay set will begin to
flash:
Spin cycle
Drying
Note:
- during draining, the LED corresponding to the
Spin cycle phase will be turned on.
- when the drying cycle is complete, the indicator
light relative to phase
will flash, to indicate that
As time passes, the remaining delay will be
the DRYING knob needs to be set back to the 0
displayed, and the corresponding LED will flash:
setting.
Function buttons
The FUNCTION BUTTONS also act like LEDS.
When a function is selected, the corresponding
button is illuminated.
If the function selected is incompatible with the
programme set, the button will flash and the
function will not be enabled.
Once the set delay is complete, the flashing LED will
turn off and the programme set will start.
If you set a function that is incompatible with
another function you selected previously, only the
last one selected will be enabled.
ON-OFF/DOOR LOCK led:
If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any
damages, wait for the LED to flash before you open the appliance door.
! The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED
indicates there is an abnormality. Call for Technical Assistance.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting and Programmes
6. Add the detergent and any fabric softener (see page 8).
7. Start he programme by pressing the START/RESET
button.
Briefly: starting a programme
GB
1. Switch the Washer-dryer on by pressing button
All the LEDS will light up for a few seconds and
the ON-OFF/DOOR LOCK Led will begin to flash.
2. Load your laundry into the washing machine and
shut the appliance door.
3. Set the PROGRAMME knob to the programme
required.
4. Set the wash temperature (see page 7).
5. Set the drying cycle if necessary (see page 7).
.
To cancel it, keep the START/RESET button pressed
for at least 2 seconds.
8. When the programme is finished, the ON-OFF/
DOOR LOCK Led will flash to indicate that the
appliance door can be opened. Take out your
laundry and leave the appliance door ajar to allow
the drum to dry thoroughly. Turn the Washer-dryer
off by pressing button
.
Programme table
Cycle
length
(minutes)
Detergent
Type of fabric and
degree of soil
Te m p e -
rature
Fabric
softener
Programmes
Description of wash cycle
pre-
wash
wash
Standard
Extremely soiled whites
(sheets, tablecloths, etc.)
Pre-wash, wash cycle, rinse cycles,
intermediate and final spin cycles
1
2
2
2
3
4
4
5
6
7
8
90°C
90°C
60°C
40°C
40°C
60°C
40°C
40°C
30°C
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
135
125
110
105
70
Extremely soiled whites
(sheets, tablecloths, etc.)
Wash cycle, rinse cycles,
intermediate and final spin cycles
Heavily soiled whites and fast
colours
Wash cycle, rinse cycles,
intermediate and final spin cycles
Heavily soiled whites and delicate
colours
Wash cycle, rinse cycles,
intermediate and final spin cycles
Slightly soiled whites and delicate
colours (shirts, jumpers, etc.)
Wash cycle, rinse cycles,
intermediate and final spin cycles
Heavily soiled fast colours
(baby linen, etc.)
Wash cycle, rinse cycles, anti-crease
or delicate spin cycle
75
Heavily soiled fast colours
(baby linen, etc.)
Wash cycle, rinse cycles, anti-crease
or delicate spin cycle
60
Wash cycle, rinse cycles anti-crease
or delicate spin cycle
Wool
50
Very delicate fabrics
(curtains, silk, viscose, etc.)
Wash cycle, rinse cycles, anti-crease
or draining cycle
45
Drying cotton
Drying delicates
Time 4 you
Heavily soiled whites and fast
colours
Wash cycle, rinse cycles,
intermediate and final spin cycles
9
60°C
40°C
30°C
•
•
•
•
•
•
60
40
30
Delicate colours
(all types of slightly soiled garments)
Wash cycle, rinse cycles, delicate
spin cycle
10
11
Delicate colours
(all types of slightly soiled garments)
Wash cycle, rinse cycles and delicate
spin cycle
Sport
Cold wash (without detergents), wash
cycle, rinse cycles, and delicate spin cycle
12
13
Sports shoes (MAX. 2 pairs)
30°C
30°C
•
•
•
•
50
60
Fabrics for sportswear
(Tracksuits, shorts, etc.)
Wash cycle, rinse cycles,
intermediate and final spin cycles
PARTIAL PROGRAMMES
Rinse
•
Rinse cycles and spin cycle
Draining and spin cycle
Drain
Spin cycle
Drain
Notes
-For programme 9, we advise against exceeding a wash load of 3.5 kg.
-For programme 13 we advise against exceeding a wash load of 2 kg.
-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.
Special programme
Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts
30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30°C), you can wash
different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Personalisations
C
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6).
GB
The temperature can be lowered, or even set to a cold wash ( ).
The data contained in the
table are purely indicative.
Table of drying times
Set the drying cycle
Turn the DRYING knob to set the desired drying type.
Fabric
type
Load type
Max.
load
(kg)
Cup-
board
Hanger
Iron
Two options are available:
A - Based on time: From 40 minutes to 150.
Cotton,
Linen
Clothing of different sizes
B - Based on the damp level of the dry clothes:
4
4
130
130
90
120
120
80
110
110
70
Iron
: slightly damp clothes, easy to iron.
: dry clothes to put away.
Cotton
Terry towels
Hanger
Cupboard
: very dry clothes, recommended for towelling
Terital,
Cotton
Sheets, Shirts
2,5
and bathrobes.
A cooling stage is foreseen at the end of the drying cycle.
Acrylics
Nylon
Pyjamas, socks, etc.
1
1
65
65
60
60
60
60
Slips, tights, stockings, etc.
If your laundry load to wash and dry is exceptionally in excess
of the maximum load foreseen (see table opposite), perform
the wash cycle, and when the programme is complete, divide up the garments and put part of them back in the
drum. Now follow the instructions provided for a dry only cycle. Repeat this procedure for the remainder of the load.
Dry only
Turn the PROGRAMME knob to one of the drying settings (7-8) depending on the type of fabric, then select the
desired drying type using the DRYING knob.
Important: - A spin cycle is carried out during the drying if you have set a cotton programme and a level of
dryness (Cupboard
, Hanger
, Iron
).
- For cotton loads of less than 1 Kg, use the drying programme designed for delicate fabrics.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
Enabled with
programmes:
Function
Effect
Comments
Press the button repeatedly until the LED corresponding to the
desired delay is turned on.
The fifth time the button is pressed, the function will be disabled.
N.B.: Once you have pressed the Start/Reset button, the delay
can only be decreased if you wish to modify it.
Delays the start
of the wash by
up to 9 hours.
All
Delay Timer
This option
reduces the
amount of
creasing on
fabrics, making
them easier to
iron.
When this function is set, programmes 4, 5, 6 will end with the
laundry left to soak (Anti-crease) and the Rinse cycle phase
3, 4, 5, 6,
9, 10,
Rinse cycle.
LED
- to conclude the cycle, press the START/RESET button;
- to run the draining cycle alone, set the knob to the relative
symbol and press the START/RESET button.
will flash.
Easy iron
1, 2, 3, 4, 9,
10, 12, 13,
Rinse cycle.
Increases the
efficiency of the
rinse.
Recommended when the appliance has a full load or with large
quantities of detergent.
Extra Rinse
All
programmes
except for 6
and draining.
Reduces the
spin speed.
1000-500
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergents and laundry
Detergent dispenser
Special items
GB
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme 6
which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1 kg.
appliance and even pollute the environment.
Open up the detergent
dispenser and pour in
the detergent and fabric
softener, as follows.
3
2
1
compartment 1: Detergent for pre-wash
(powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
! Do not use hand wash detergent because it may
form too much foam.
Preparing your laundry
• Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
• Empty all pockets and check for loose buttons.
• Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 5 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and advice
! The Washer-dryer was designed and built in
Disposal
compliance with the applicable international safety
GB
regulations. The following information is provided for
your safety and should consequently be read carefully.
• Disposing of the packaging material:
observe local regulations, so the packaging can
be re-used.
General safety
• Disposing of an old Washer-dryer:
• This appliance has been designed for non-
professional, household use and its functions must
not be changed.
before scrapping your appliance, cut the power
supply cable and remove the appliance door.
Saving energy and respecting the
environment
• This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
Environmentally-friendly technology
If you only see a little water through your appliance
door, this is because thanks to the latest Indesit
technology, your washing machine only needs less
than half the amount of water to get the best
results: an objective reached to respect the
environment.
• Never touch the washing machine when barefoot
or with wet or damp hands or feet.
• Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
• Do not open the detergent dispenser while the
appliance is in operation.
Saving on detergent, water,
energy and time
• Do not touch the drain water as it could reach
very high temperatures.
• To avoid wasting resources, the Washer-dryer
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
• Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
• The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
• In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
• Always keep children well away from the
appliance while in operation.
• Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on
energy.
• The appliance door tends to get quite hot during
the wash cycle.
• Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
• Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
• Before loading your laundry into the washing
machine, make sure the drum is empty.
• During the drying phase, the door tends to get
quite hot.
• Do not use the appliance to dry clothes that have
been washed with flammable solvents (e.g.
trichlorethylene).
• If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
The Delay Timer option (see page 7) helps to
organise your wash cycles accordingly.
• Do not use the appliance to dry foam rubber or
similar elastomers.
• Make sure that the water tap is turned on during
the drying cycles.
• If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
• This washer-dryer can only be used to dry clothes
which have been pre-washed in water.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
Cutting off the water or electricity
supply
Cleaning the pump
GB
The Washer-dryer is fitted with a self-cleaning pump
that does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into
the pre-chamber that protects the pump, situated in
the lower part of the same.
•
Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
•
Unplug your appliance when cleaning it and
during all maintenance operations.
! Make sure the wash cycle has ended and unplug
the appliance.
Cleaning your appliance
To access the pre-chamber:
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
1. using a screwdriver,
remove the cover panel
on the lower front of the
Washer-dryer (see
figure);
Cleaning the detergent dispenser
Remove the dispenser
by raising it and pulling it
out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
2. unscrew the lid
rotating it anti-
clockwise (see figure): a
little water may trickle
out. This is perfectly
normal;
Caring for your appliance door and
drum
•
Always leave the appliance door ajar to prevent
unpleasant odours from forming.
3. clean the interior thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong and
a cracked hose could easily split open.
! Never use hoses that have already been used.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Your Washer-dryer could fail to work. Before calling for Assistance (see page 12), make sure the problem can't
GB
easily be solved by consulting the following list.
Possible causes/Solution:
Problem
• The appliance is not plugged into the socket, or not enough to
make contact.
The washer-dryer won't start.
• There has been a power failure.
• The appliance door is not shut properly.
The wash cycle won't start.
• The
button has not been pressed.
• The START/RESET button has not been pressed.
• The water tap is not turned on.
• A delayed start has been set (using the Delay Timer, see page 7).
• The water inlet hose is not connected to the tap.
• The hose is bent.
The washer-dryer fails to load
water.
• The water tap is not turned on.
• There is a water shortage.
• The water pressure is insufficient.
• The START/RESET button has not been pressed.
• The drain hose is not fitted between 65 and 100 cm from the floor
(see page 3).
The washer-dryer continuously
loads and unloads water.
• The free end of the hose is underwater (see page 3).
• The wall drainage system doesn't have a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and call for Assistance. If the dwelling is on one of
the upper floors of a building, there may be drain trap problems causing the
Washer-dryer to load and unload water continuously. In order to avoid such
an inconvenience, special anti-drain trap valves are available in shops.
• The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 6).
• The Easy iron option is enabled: to complete the programme, press
the START/RESET button (see page 7).
The washer-dryer does not
drain or spin.
• The drain hose is bent (see page 3).
• The drain duct is clogged.
• The drum was not unblocked correctly during installation (see page 2).
• The Washer-dryer is not level (see page 2).
The washer-dryer vibrates too
much during the spin cycle.
• The Washer-dryer is closed in between furniture cabinets and
the wall (see page 2).
• The water inlet hose is not screwed on correctly (see page 2).
• The detergent dispenser is obstructed (to clean it, see page 10).
• The drain hose is not secured properly (see page 3).
The washer-dryer leaks.
• Call for Assistance because this means there is an abnormality.
The ON-OFF/DOOR LOCK Led
flashes rapidly at the same
time as at least one other LED.
• The detergent is not suitable for machine washing (it should bear
the definition "for washing machines" or "hand and machine wash",
or the like).
There is too much foam.
• You used too much detergent.
• The appliance is not plugged into the socket, or not enough to make contact.
• There has been a power failure.
The washer-dryer does not dry.
• The appliance door is not shut properly.
• A delayed start has been set (using the Delay Timer, see page 7).
• the DRYING knob is on the 0 setting.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
195043595.00
03/2004
-
Xerox Business Services
Before calling for Assistance:
• Check whether you can solve the problem on your own (see page 11);
• Restart the programme to check whether the problem has been solved;
GB
• If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
! Always request the assistance of authorised servicemen.
Notify the operator of:
• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N).
This information can be found on the data plate situated on the rear of the washer-dryer.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|