Indesit Washer Dryer WD 12 S User Manual

M
Washer-dryer  
Instructions for installation and use  
WD 12 S  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M
Dividing your garments  
What goes in your washer-dryer?  
Before washing, you can do a great deal to ensure better results. Divide your garments  
according to fabric and colour. Read the labels, follow their guidelines.  
according to fabric and  
colour, is very important  
for good results  
Before washing.  
The labels say it all.  
Big and small happily  
Divide your washing according Always look at the labels: they together.  
This washer-dryer has a special  
to the type of fabric and colour tell you everything about your  
fastness. garment and how to wash it in  
Empty all pockets (coins, paper, the best possible way.  
electronic control device for even  
distribution: before the spin cycle  
starts, this device allows the  
money and small obejects) and The table on page 6 shows all  
ensure all loose buttons are meanings behind these garments  
to  
positions  
themselves, to minimise noise  
and vibrations during the spin  
cycle.  
repaired or removed prior to symbols. Their recom-  
loading.  
mendations are important to  
achieve better wash results.  
Starting the washer-dryer  
After installing your new washer-dryer, start a wash cycle  
by setting programme "1" at 90 degrees.  
Starting your washer-dryer in  
the right way is important for the  
quality of your wash, to help  
prevent future problems and  
enhance life expectancy of your  
appliance. Once you have  
loaded your washer-dryer and  
added the detergent together  
with any fabric conditioner,  
always check that:  
1.The door is closed correctly.  
2. The plug is secured in the  
socket.  
3. The water supply is turned  
on.  
4. Selector knob A is positioned  
on one of the symbols (Stop/  
Reset).  
Choosethedesiredprogramme  
The programme is selected  
according to the type of garments  
thatneedtobewashed.Tochoose  
a programme, refer to the table on  
page 4. Turn knob A until the  
selected programme is aligned  
with the mark on the knob, turn  
knob B to the desired temperatu-  
re settings, check that knob C is  
in the desired position, if  
necessary use buttons E, F, G  
and lastly, press on/off button H  
(I position).  
For more delicate  
garments:  
protect underwear, tights  
and stockings and delicate  
items by placing them in a  
canvas pouch  
Always disconnect electricity at  
the socket and turn off the water  
supply.  
Remember that, in the event  
of a power failure, or should  
the washer-dryer switch itself  
off, the programme chosen  
will remain in its memory.  
At the end of the wash cycle...  
Lamp I will flash quickly for a few  
seconds, then it will begin  
flashing more slowly.  
Then turn the washer-dryer off  
by pressing on-off button H  
(O position).You can now open  
the washer-dryer door safely.  
After having removed the  
freshly cleaned washing, leave  
the door open to allow air  
circulation inside the drum.  
How to eliminate the most common stains  
Ink and biro Dab with a wad of cotton soaked in methyl alcohol or alcohol at 90°.  
Tar Dab with fresh butter, rub in turpentine then wash immediately.  
Wax Scrape away, then run a hot iron between two sheets of absorbent paper. Then rub in cotton with turpentine or  
methyl alcohol.  
Chewing gum Rub in nail polish remover and wipe with a clean rag.  
Mold Cotton and white linen should be placed in a solution of 5 parts water, one bleach and a spoon of vinegar, then  
washed immediately. For other white fabrics, use hydrogen peroxide at 10 volumes and wash immediately.  
Lipstick Dab with ether on wool or cotton. Use tricloroetilene for silk.  
Nail polish Place a sheet of absorbent paper on the side of the stain, wet it with nail polish remover, shifting the  
garment as the sheet gradually changes colour.  
Grass Dab with a wad of cotton soaked in methyl alcohol.  
Instructions for installation and use  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Understanding the control panel  
Here I’m in command  
Making the right choice is important. And it’s easy.  
E
G
L
F
I
A
B
D
C
H
Programme selector knob  
Use this knob to select the wash It is used to set the wash tempe-  
programme. rature in the recommended  
Turn this knob clockwise only. programme table on pag. 4. It also  
To select a programme, you allows you to reduce the tempe-  
should turn the knob so that the rature recommended for the  
Temperature control knob  
Detergent dispenser  
It is divided into three  
compartments:  
1.Detergent for pre-wash;  
2.Detergent for the main cycle  
wash;  
Extra Economy  
Reduces water consumption  
during the rinse cycles. We  
recommend that you use this  
function only with small laundry  
loads, dosing the detergent  
proportionally.  
3.Fabric conditioner.  
symbol/number of the desired  
selected programme, and even to  
programme is in line with the set a cold wash cycle ( ).  
pointer on the knob.  
Anti-crease  
Now press on/off button H  
On-off  
(position I), pilot lamp I will start  
flashing.  
After 5", the setting will be  
accepted, pilot lamp I will stop  
flashing (staying lit) and the wash  
cycle will begin.  
Should you wish to interrupt the  
programme in progress or set a  
This button allows you to  
interrupt a programme (on  
symbol ) keeping the washing  
soaking in water before the spin  
cycle. It is a very useful button  
in particular because it can be  
used for delicates and  
synthetics. It is only to be used  
with wash programmes for  
synthetic fabrics, silk and  
curtains when it is impossible for  
you to take the washing out  
immediately.Before opening the  
washing machine door, finish the  
wash cycle as follows:  
When button H is pressed, the  
washer-dryer is switched on,  
when it is not the machine is  
switched off.  
Turning the appliance off  
does not cancel the selected  
programme.  
Drying cycle knob  
Use this knob to select the  
desired drying cycle. Two  
options are available:  
A - Based on time:  
From 40 minutes to 150.  
B - Based on the damp level of  
the dry clothes:  
new one, select one of the  
Iron  
:use this slightly damp  
symbols (Stop/Reset) and wait  
5" : when the cancellation has  
been accepted, pilot lamp I  
flashes, and you can then turn the  
appliance off.  
After the wash cycle has been set  
and accepted by the washing  
machine, turning the knob will  
have no effect (except for when  
it is on position Stop/Reset).  
On-off lamp / door locked  
setting for clothes that you  
intend to iron to reduce effort  
and save energy in the drying  
cycle.  
Lamp I flashes slowly when the  
appliance is switched on and  
awaiting instructions and at the  
end of a cycle, indicating that the  
door can be opened. It flashes  
quickly when the door should  
not be opened. A steady light  
means the appliance has  
Wardrobe  
:use this setting  
when you want dry clothes that  
can be stored after hanging for  
a short while.  
Silk and curtains: press button E  
and the machine will drain the  
water.  
Synthetic fabrics: press button E  
if you want a spin cycle, or turn  
Extra dry  
: use this setting  
accepted  
the  
selected  
when you want very dry clothes.  
programme.  
knob A to symbol  
the water to be drained.  
N.B.:  
if you want  
A cooling stage is foreseen at  
the end of the drying cycle.  
Drying cycle lamp  
When this lamp is on, it means  
that knob C has been set on a  
drying cycle and at the end of the  
wash cycle, the appliance will run  
the selected tumble drying cycle.  
With “Daily wash”, this function  
is not performed.  
Slow spin  
Use this button to reduce the  
spinning speed from 1200 to  
600 rpm for the cotton and linen  
programmes and from 850 to  
600 rpm for the synthetic  
fabrics programmes.  
3
2
1
The detergent dispenser is here.  
3
Instructions for installation and use  
Download from Www.Somanuals.com. All Manuals Search And Download.  
What are you washing today?  
A programme for all seasons  
Type of fabric and degree of soil  
Programme Temperature Detergent Detergent Fabric  
Length of Description of wash cycle  
knob  
knob  
for  
prewash  
for wash  
softener  
the cycle  
(minutes)  
COTTON  
Exceptionally soiled whites  
(sheets, tablecloths, etc.)  
Warm prewash, wash cycle at 90°C, rinse  
cycles, intermediate and final spin cycles  
165  
145  
130  
95  
1
2
3
4
90°C  
Exceptionally soiled whites  
(sheets, tablecloths, etc.)  
Wash cycle at 90°C, rinse cycles,  
intermediate and final spin cycles  
90°C  
60°C  
40°C  
Heavily soiled whites and fast colours  
Wash cycle at 60°C, rinse cycles,  
intermediate and final spin cycles  
Slightly soiled whites and delicate  
colours (shirts, jumpers, etc.)  
Wash cycle at 40°C, rinse cycles,  
intermediate and final spin cycles  
Rinse cycles  
Rinse cycles, intermediate and final  
spin cycles  
Spin cycle  
Draining and final spin cycle  
Drying cycle for cotton fabrics  
Stop/Reset  
Interrupts/Cancels the selected programme  
SYNTHETICS  
Heavily soiled fast colour synthetics  
(baby linen, etc.)  
Wash cycle at 60°C, rinse cycles,  
anti-crease or delicate spin cycle  
100  
95  
5
6
7
8
60°C  
50°C  
40°C  
30°C  
Heavily soiled fast colour synthetics  
(baby linen, etc.)  
Wash cycle at 50°C, rinse cycles,  
anti-crease or delicate spin cycle  
Delicate colour synthetics  
(all types of slightly soiled garments)  
Wash cycle at 40°C, rinse cycles,  
anti-crease or delicate spin cycle  
70  
Delicate colour synthetics  
(all types of slightly soiled garments)  
Wash cycle at 30°C, rinse cycles and  
delicate spin cycle  
30  
Rinse cycles  
Rinse cycles, anti-crease or delicate  
spin cycel  
Fabric softener  
Rinse cycles with automatic introduction of  
softener, anti-crease or delicate spin cycle  
Spin cycle  
Draining and delicate spin cycle  
Drying cycle for synthetic fabrics  
Interrupts/Cancels the selected programme  
Stop/Reset  
DELICATES  
Wool  
Wash cycle at 40°C, rinse cycles and  
delicate spin cycle  
60  
50  
9
40°C  
30°C  
Particularly delicate garments and  
fabrics (curtains, silk, viscose, etc.)  
Wash cycle at 30°C, rinse cycles,  
anti-crease or draining  
10  
Rinse cycles  
Spin cycle  
Draining  
Rinse cyclesi, anti-crease or draining  
Draining and delicate spin cycle  
Draining  
Interrupts/Cancels the selected programme  
Stop/Reset  
Important: to cancel the wash programme you have just set, select one of the symbols (Stop/Reset) and wait for at least 5 seconds.  
The data found in the table is purely indicative, and can vary according to the quantity and type of washing, the water system temperature and  
the room temperature.  
Special programme  
Daily wash Your washer-dryer has a programme available for the washing of lightly soiled garments in a short amount of time.  
By setting programme 8 at a temperature of 30°C, you can wash different types of fabrics together (except for wool and silk), with a  
maximum load of 3 kg. This programmes allows you to save on both time and energy as it only lasts around 30 minutes.  
We recommend the use of liquid detergent.  
Instructions for installation and use  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to dry  
A.  
Fabric  
type  
A combinedWashing and Dry only  
Drying Programme  
Drying time (Min.)  
Load type Max. load  
(kg)  
Once you have loaded the  
Extra  
dry  
Wardrobe Iron  
Look at table A to the side and washing that needs drying (2,5  
follow the instructions provided kg max. for cottons, see table  
for MAX load to have an for other fabrics ), make sure  
automatic washing and drying that:  
Cotton,  
Linen  
Clothing of  
different  
sizes  
cycle.  
- the door is shut correctly;  
2,5  
145  
130  
120  
Follow the instructions for wash - the plug is inserted in the socket;  
only (see page 2, the paragraph - the water tap is turned on;  
entitled "Starting the Washer- - button H has not been pressed  
Dryer") and use knob C to set (O position).  
the type of drying cycle desired,  
Cotton  
Terry  
towels  
2,5  
2,5  
1
145  
100  
65  
130  
90  
120  
85  
Terital,  
Cotton  
Sheets,  
Shirts  
then press button H (I position). And now set the wash cycle  
knob  
If the laundry load to be washed  
and dried exceeds the  
Set knob A on the appropriate  
Acrylics  
Nylon  
Pyjamas,  
socks, etc.  
drying setting  
depending on  
60  
60  
maximum load foreseen (see  
table A), then follow the  
instructions provided for wash  
only (see page 2, the paragraph  
entitled "Starting the Washer-  
Dryer").  
When the wash cycle has  
finished, remove your washing,  
divide it up and replace part of it  
inside the drum.  
the type of fabric, select the type  
of drying cycle required using  
knob C and then press on-off  
button H (I position).  
Slips, tights,  
stockings,  
etc.  
1
65  
60  
60  
At the end of the drying cycle...  
Wait for lamp I to flash slowly,  
then turn the washer-dryer off by  
pressing on-off button H  
(O position). Now you can open  
the appliance door. Once you  
have removed the washing from  
the appliance, leave the door  
open or ajar to avoid the  
formation of bad odours and  
turn off the water tap.  
The data contained in the table are purely indicative.  
For cotton loads of less than 1 Kg, use the drying programme  
designed for synthetic fabrics.  
Now follow the instructions  
provided for a dry only cycle.  
Repeat this procedure for the  
remainder of the load.  
IMPORTANT  
WARNING  
A spin cycle is carried out during the drying if you have set a  
cotton programme and a level of dryness (Extra dry  
Wardrobe , Iron ).  
- During the drying phase, the door tends to get quite hot.  
- Do not use the appliance to dry clothes that have been  
washed with flammable solvents (e.g. trichlorethylene).  
- Do not use the appliance to dry foam rubber or similar  
elastomers.  
,
- Make sure that the water tap is turned on during the drying  
cycles.  
- This washer-dryer can only be used to dry clothes which  
have been pre-washed in water.  
5
Instructions for installation and use  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Understanding labels  
Learn the meaning of these symbols and you will get better  
results, your garments will last longer resulting in an  
improved wash.  
All over Europe, garment labels These symbols are divided in  
contain messages expressed in five different categories and  
small yet important symbols. shapes: washing  
, bleaching  
Understanding them is very  
important if you want to get  
better results and treat your  
garments the way they deserve  
to be treated.  
, ironing  
and drying  
, dry cleaning  
.
Useful tips  
Turn shirts inside out to get better results  
and make them last longer.  
Always empty pockets of their contents.  
Look at the label: it will always give you useful  
advice.  
When loading your washing, try to have a mixture  
of large to small items.  
Make sure you select the right  
temperature!  
Consult and learn the symbols in this table: they will help you  
obtain a better wash, treat your clothes properly, and get a  
better performance out of your washer-dryer.  
Wash  
Bleaching  
Ironing  
Dry cleaning  
Drying  
Strong  
action  
Delicate  
action  
High  
Temp.  
Low  
Temperat.  
A
c
l
Wash at  
95°C  
Bleaching only in  
cold water  
Hot iron at max  
200°C  
Dry clean with any  
solvent  
Machine dryable  
P
Dry clean only with  
perchloride, benzine  
av., pure alcohol,  
R111 and R113  
Medium hot  
ironing at  
max 150°C  
Wash at  
60°C  
Do not machine  
dry  
Do not bleach  
F
Dry clean with av.  
benzine, pure alcohol  
and R113  
Wash at  
40°C  
Iron at max  
110°C  
Spread to dry  
Hang to dry  
without spin  
drying  
Wash at  
30°C  
Not ironable  
Do not dry clean  
Dry on clothes  
hanger  
Hand wash  
Not  
washable in  
water  
Instructions for installation and use  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Useful tips  
Never use your washer-  
How much does it weigh?  
Holidays: unplug the  
appliance.  
dryer to wash... torn, fraying or 1 sheet 400-500 gr.  
non-hemmed linen. If it is 1 pillow case 150-200 gr.  
absolutely neccessary, place it in 1 tablecloth 400-500 gr.  
a bag for protection. Do not wash 1 bathrobe 900-1,200 gr.  
It is recommended that you  
should unplug the machine from  
the socket and turn off the water  
supply. Leave the door ajar to  
allow air circulation to the draw  
coloured linen with whites.  
1 towel 150-250 gr.  
Watch the weight!  
Coloured T-shirts, printed and the door gasket area.This will  
For best results, do not exceed onesandshirtslastlongerif turned prevent unpleasant odours.  
the weight limits stated below inside out before washing.  
(figures show weight of dry Printed T-shirts and sweatshirts  
garments):  
shouldalwaysbeironedinsideout.  
- Resistant fabrics:  
5 kg maximum  
- Synthetic fabrics:  
2.5 kg maximum  
- Delicate fabrics:  
2 kg maximum  
Dungaree alert.  
WOOLCYCLE  
For best results, we  
recommend you use a  
specific detergent, taking  
care not to wash more than  
1 kg of laundry.  
Very popular “salopette” type  
overalls have straps with hooks  
that can damage the drum of your  
washer-dryer or other garments  
during the wash.To minimise the  
risk, place hooks in the pocket  
and fasten with safety pins.  
- Pure new wool:  
1 kg maximum  
How to wash almost anything  
Curtains.  
Quilted coats and anorak.  
Trainers.  
Curtains tend to crease a great You can wash quilted coats and Once you have removed mud  
deal. A useful tip to reduce wind-cheaters, too, if they are and dirt from trainers, you can  
creasing: fold the curtains and padded with goose or duck even wash them with jeans or  
place them in a pillow case or down. Do not load more than any other tough garments. Do  
mesh bag. Do not load anything 2-3 kg and never load 5 kg. not wash trainers with whites.  
else inside the appliance, this Repeat rinse once or twice  
will ensure that the overall using the gentle spin.  
weight does not exceed the half  
load. Remember to use the  
specific programme 10 which  
automatically excludes the spin  
cycle.  
7
Instructions for installation and use  
Download from Www.Somanuals.com. All Manuals Search And Download.  
It’s important for a good wash  
Useful tips about the detergent dispenser  
The first secret is the easiest: the detergent dispenser is  
opened by pull it outwards.  
In compartment 1:  
Detergent for pre-washing (powder)  
In compartment 2:  
Detergent for washing  
(powder or liquid)  
You must follow the dosage Special containers are sold with  
recommendations provided by liquid or powder detergents for  
the manufacturers when adding placing inside the washer-dryer  
detergent or fabric conditioner. drum, these are positioned  
Doses will vary according to the according to the instructions  
wash load, the water hardness found in the detergent box  
In compartment 3:  
Additives (softeners, perfumes, etc.)  
3
2
1
and how soiled the washing is.  
Never use hand wash  
Experience will help you select detergent, because it may form  
the right dosage almost too much foam, which could  
automatically: it will become your damage the washer-dryer.  
secret.  
Detergents that are specifically  
Ensure no overfilling when formulated for both hand and  
adding fabric conditioner in machine wash are an  
compartment 3.  
exception.  
The washer-dryer automatically One last secret: when washing  
adds the softener to the wash in with cold water, always reduce  
each programme.  
the amount of detergent you use:  
Liquid detergent is poured into it dissolves less easily in cold  
compartment 2 just a few water than in hot water, so part  
seconds before starting the of it would be wasted.  
wash cycle.  
Remember that liquid detergent  
is only designed for wash  
cycles of up to 60 degrees on  
non pre-wash items.  
The detergent dispenser can be  
removed and cleaned: pull it outwards,  
as indicated in the figure. Then leave it  
under running water for a few minutes.  
A guide to environmentally  
friendly and economic use  
of your appliance.  
Cutting costs efficiently  
MAXIMISE THE LOAD SIZE  
Achieve the best use of energy, water, detergent and time by using the recommended  
maximum load size.  
SAVE up to 50% energy by washing a full load instead of 2 half loads.  
DO YOU NEED TO PRE-WASH?  
For heavily soiled laundry only!  
SAVE detergent, time, water and between 5 to 15% energy consumption by NOT  
selecting Prewash for slight to normally soiled laundry.  
IS A HOT WASH REQUIRED?  
Pretreat stains with stain remover or soak dried in stains in water before washing to  
reduce the necessity of a hot wash programme.  
SAVE up to 50% energy by using a 60°C wash programme.  
BEFORE USING A DRYING PROGRAMME ...  
SAVE energy and time by selecting the highest suitable spin speed to reduce the water  
content in laundry before using a drying programme.  
Instructions for installation and use  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Before calling, read the following  
In most cases, when your washer-dryer fails to work, the problems arising can  
be easily solved without having to call for a technician. Before calling for  
assistance, always check these points.  
But where did all the water go?  
The washer-dryer fails to  
the door is open or not shut  
properly.  
Simple: with the new Indesit technology, you need less than  
half of it, to get good results on twice as much!  
start.  
This is why you cannot see the water through the door:  
because there is little, very little of it, to respect the  
environment yet without renouncing maximum cleanliness.  
And, on top of that, you are also saving electricity.  
Is the On/Off button  
pressed?  
If it is, then a programmed start  
has been set.  
Is the plug correctly inserted  
into the socket? It could have  
been moved whilst cleaning.  
Is there electricity in the  
house?  
Is the programmed start  
knob, in the correct position  
A circuit breaker may have  
switched off as a result of too  
many electrical appliances  
working at the same time. Or  
maybe due to a general failure  
in your entire area.  
for  
those  
models  
concerned?  
Is the water supply turned  
on? For safety reasons, if the  
washer-dryer does not load  
water, it cannot start a wash  
cycle.  
Is the washer-dryer door  
closed properly?  
For safety reasons, the  
washer-dryer cannot work if  
off, select one of the symbols  
stop/reset , then switch it  
back on. If the knob continues  
to turn, call for assistance  
because it is showing an  
anomaly.  
The washer-dryer fails to  
fill with water.  
Is the hose correctly  
connected to the tap?  
Is there a water shortage ?  
There could be work in  
progress in your building or  
street.  
RIGHT WRONG  
The washer-dryer  
continuously fills and  
drains water.  
Leave the washer-dryer  
plugged in while  
Turn off the water  
supply after use.  
This will eliminate  
the possibility of  
leakage.  
cleaning.  
Is there sufficient water  
pressure? The autoclave  
may be malfunctioning.  
Even during maintenance,  
the appliance should  
always be unplugged.  
Is the drain hose positioned  
too low? It must be installed  
at a height ranging from 60 to  
100 cm.  
Always leave the  
Is the tap filter clean? If the  
water is very calcareous, or  
if work has recently been  
carried out on the water  
piping, the tap filter could be  
clogged with particles and  
debris.  
Use solvents and  
appliance door ajar  
to avoid bad odours.  
aggressive abrasives.  
Never use solvents or  
abrasives to clean the  
external and rubber parts  
of the washer-dryer.  
Is the end of the hose  
immersed in water?  
Clean the  
appliance’s  
Does the wall drainage  
system have a breather  
pipe? If the problem persists  
even after these checks, turn  
the water supply off the  
machine and call for  
assistance.  
If you live on an upper floor of  
your building, there may be a  
problem with your drain trap.  
To solve this problem, a  
special valve must be  
installed.  
exteriors gently.  
To clean the  
Neglect the detergent  
dispenser.  
It is removable and can  
easily be cleaned by  
leaving it under running  
water.  
exteriors and the  
rubber parts of the  
appliance, always  
use a soft cloth  
dipped in warm and  
soapy water.  
Is the rubber hose kinked?  
The tract of the rubber hose  
bringing water to washer-  
dryer must be as straight as  
possible. Make sure it is not  
squashed or kinked.  
Go on holiday without  
thinking about her.  
The programme selector  
knob keeps turning?  
Before leaving, always  
make sure that the  
washer-dryer is  
Wait a few minutes for the  
drain pump to empty the  
tub, switch the washer-dryer  
unplugged and that the  
water supply is turned off.  
9
Instructions for installation and use  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Is the drain hose kinked?  
The tract of the drain hose  
must be as straight as  
possible. Make sure the drain  
hose is not squashed or  
kinked.  
Is there space between the  
machine and adjacent  
units? If it is not a built-in  
model, the washer-dryer will  
oscillate a bit during the spin  
cycle. A few cm of space  
should therefore be left  
around it.  
Is the washer-dryer’s drain  
duct clogged? Is there an  
extension of the drain hose?  
If so, is it positioned  
incorrectly, blocking the  
water flow?  
The washer-dryer does  
not drain or spin.  
Too much foam.  
Is the detergent appropriate  
for machine washing?Check  
whether the definition on its  
label reads “for machine wash”  
or “hand and machine wash”,  
or any other similar wording.  
Does  
the  
selected  
programme incorporates  
water draining? Some  
programmes stop at the end  
of the wash cycles and  
draining will have to be  
selected manually.  
The washer-dryer leaks.  
Is the correct amount being  
used?An excessive amount of  
detergent, besides producing  
too much foam, does not  
guarantee a more effective  
wash, and causes scaling in the  
internal parts of the appliance.  
Is the “Anti-crease"  
function -where provided -  
enabled? This function  
requires manual selection for  
draining.  
Is the metal ring of the inlet  
hose properly attached?  
Turn off the water supply,  
unplug the appliance and try  
tightening its attachment  
without forcing it.  
Excessive vibration  
during the spin cycle.  
Is the drain pump clogged?  
To check it, turn off the water  
supply, unplug the washer-  
dryer and follow the  
instructions on page 13, or  
call for technical assistance.  
Have all transit screws been  
removed durind instal-  
lation? See the following  
Is the detergent dispenser The washer-dryer does  
obstructed? Remove and not dry.  
wash it under tap water.  
page  
on  
installation  
procedures.  
Check whether:  
Is the drain hose well  
the plug has been correctly  
attached?Turn off the water  
inserted into the socket;there  
supply, unplug the appliance  
is electricity in your home; the  
and try tightening its  
appliance door has been shut  
attachment.  
Has the washer-dryer been  
levelled correctly? The  
levelling of the appliance  
Always get  
assistance from  
authorised  
should  
be  
checked  
properly; a delayed start (if  
periodically. Adjust the feet  
and check them with a level.  
available) has not been  
selected; programme knob A  
has been set to position  
(Stop/Reset); the drying cycle  
knob C has been set to  
position 0.  
technicians and  
always insist on  
original spare parts.  
The washer-dryer doesn't  
dry properly.  
Technical characteristics  
Model  
WD 12 S  
Check whether:  
the end of the drain hose is  
underwater; the drain pump is  
obstructed; the advice given  
on the maximum loads has  
been taken; the water tap has  
been turned on.  
Dimensions  
width 59,5 cm  
height 85 cm  
depth 53,5 cm  
Capacity  
from 1 to 5 kg for the wash programme; from 1 to 2,5 kg for the drying programme  
Electrical  
voltage 230/240 Volt 50 Hz  
connections  
maximum absorbed power 2050 W  
If, despite all checks, the washer-  
dryer fails to function and the  
problem persists, call your  
nearest authorised Customer  
Service Centre, providing the  
following information:  
Water connections  
maximum pressure 1 MPa (10 bar)  
minimum pressure 0,05 MPa (0,5 bar)  
drum capacity 46 litre  
Spinning speed  
up to 1200 rpm  
- the nature of malfunction  
- the model type no.(Mod.....)  
- the serial number (S/N ....)  
This information can be found on  
the data plate situated at the back  
of the washer-dryer.  
Control programs  
wash: programme 3, temperature 60°C. Carried out with 5 kg load;  
in compliance with drying: run with a load of 2.5 kg and knob C set to position  
IEC regulation 456  
.
This appliance conforms with the following E.E.C. directives:  
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications  
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent  
modifications  
Instructions for installation and use 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and removal  
When the new  
washer-dryer arrives  
Whether new or just transported to a new house,  
installation is extremely important for the correct  
functioning of your washer-dryer.  
After removing the appliance from  
its packaging, check that it is  
Connection to the water  
mains  
intact. If in doubt, contact a  
Both hot and cold water supplies  
qualified technician immediately.  
are preferable and they should be  
The inside of the machine is  
between 34.5kN/m²(5lb/in²) and  
supported, fortransportation, by  
1034.2kN/m² (150lb/in²) pressure.  
four screws on the back panel.  
Thehosehavingthe red endfitting  
should be encountered between  
Electric connection  
the hot supply and the threaded  
connection adjacent to the letter H  
on the rear of the machine. The  
hose having the white end fittings  
should be connected between the  
cold supply and the threaded  
connection adjacent to the letter C  
on the rear of the machine.  
Remember to insert a sealing  
washer at each connection to  
ensure watertight joints. Do not  
overtighten the connections by  
using tools -hand tight is sufficient  
topreventleaks.Itisgenerallymore  
convenient to have these supplies  
away from the sink taps. Where  
no suitable hot water supply is  
available or it does not meet these  
requirements, bothinlethosesmay  
be connected to a cold supply by  
using two taps etc., or a «T»  
junction on the plumbing however,  
use of cold water only will increase  
programmetimes.  
Connecting the drain hose  
The drain hose (hooked pipe) is  
secured to the rear of the machine  
by support clips and may be  
routed to right or left as required.  
Your appliance is now supplied  
with a 13 amp fused plug it can  
be plugged into a 13 amp socket  
for immediate use. Before using  
the appliance please read the  
instructions below.  
Before using the washer-dryer,  
remove the screws, remove the  
spacers together with the rubber  
tubesattachedtothem(keepingall  
theparts)andusetheplasticplugs  
provided to fill in the holes.  
Important:Usethecap(provided)  
to close the 3 holes which housed  
the stop pin, situated in the right-  
hand part of the lower back of the  
washer-dryer.  
WARNING - THIS APPLIANCE  
MUST BE EARTHED.  
THE FOLLOWING OPERATIONS  
SHOULD BE CARRIED OUT BY A  
QUALIFIEDELECTRICIAN.  
The hook to be used in case the drain  
hose ends at a height below 60 cm.  
Replacing the fuse:  
When replacing a faulty fuse, a  
13 amp ASTA approved fuse to  
BS 1362 should always be used,  
and the fuse cover re-fitted. If the  
fuse cover is lost, the plug must  
not be used until a replacement  
is obtained.  
The drain hose should be placed  
in a stand pipe with a minimum  
internal diameter of 38 mm (1½  
inches)oritcanbepositionedover  
a sink or it can be connected as  
shown in Fig. A. The height of  
stand pipe or sink should be  
between 60 and 100 cm (24 and  
40 inches). Care must be taken  
that the hose is not obstructed,  
twisted, submerged or kinked. If  
the hose is connected with an  
airtightjoining, provisionshouldbe  
made to prevent syphoning.  
Levelling  
The washer-dryer must be  
levelled appropriatey in order to  
guaranteeitscorrectfunctioning.To  
level the appliance, the front feet  
must be adjusted; the angle of  
inclination, measuredaccordingto  
the worktop, must not exceed 2°.  
Whenplacedoncarpet, makesure  
the ventilation is not reduced.  
Note: the maximum temperature  
should not exceed 70°C (158°F).  
The rubber gasket.  
Connect the inlet hose to the  
threaded connector on the  
machine rear.  
The front feet are adjustable.  
The guide for draining into tubs and  
sinks.  
Warning!  
The company denies all  
liability if and when these  
norms are not respected.  
Retain the transit screws,  
spacers and washers.  
Should you move house  
then these should be  
Plastic bags, expanded  
styrofoam, nails and other  
packaging parts are not  
children’s toys, and are  
potentially dangerous.  
replaced to support the  
inside of the machine to  
prevent damage when  
transporting the machine.  
Water pipe inlet at the top right.  
Fig. A  
11 Instructions for installation and use  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement fuse covers:  
How to connect an alternati-  
ve plug:  
The wires in this mains lead are  
coloured in accordance with the  
following code:  
If a replacement fuse cover is  
fitted, it must be of the correct  
colour as indicated by the  
coloured marking or the colour  
that is embossed in words on the  
base of the plug. Replacements  
can be obtained directly from  
your nearest Service Depot.  
BLUE  
BROWN  
NEUTRAL(N)  
LIVE(L)  
GREEN&YELLOW EARTH(E)  
Disposing of the appliance:  
When disposing of the appliance  
please remove the plug by  
cutting the mains cable as close  
as possible to the plug body and  
dispose of it as described above.  
Removing the plug:  
If your appliance has a non-  
rewireable moulded plug and you  
should wish to re-route the mains  
cable through partitions, units  
etc., please ensure that either:  
the plug is replaced by a fused  
13 ampere re-wearable plug  
bearing the BSI mark of approval.  
or:  
the mains cable is wired directly  
into a 13 amp cable outlet,  
controlled by a switch, (in  
compliance with BS 5733) which  
is accessible without moving the  
appliance.  
GREEN &  
YELLOW  
13 ampere fuse  
BROWN  
CROSS-BAR  
CORD GRIP  
BLUE  
Disposing of the plug:  
Ensure that before disposing of  
the plug itself, you make the pins  
unusable so that it cannot be  
accidentally inserted into a  
socket.  
Instructions for connecting  
cable to an alternative plug:  
Important: the wires in the  
mains lead are coloured in  
accordance with the following  
code:  
Green &Yellow Earth  
Blue  
Brown  
Neutral  
Live  
As the colours of the wires in the  
lead may not correspond with the  
coloured markings identifyng the  
terminals in your plug, proceed as  
follows:  
Connect Green & Yellow wire to  
terminal marked E or  
or  
colouredGreenorGreen&Yellow.  
Connect Brown wire to terminal  
marked L or coloured Red.  
Connect Blue wire to terminal  
marked N or coloured Black.  
If a 13 amp plug (BS 1363) is used  
it must be fitted with a  
13 amp fuse, either in the plug or  
adaptororatthedistributionboard.  
If you are in any doubt the  
electrical supply to your machine,  
consult a qualified electrician  
before use.  
Instructions for installation and use 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Easy Care and Maintenance  
Treat your machine well and it will provide  
many years of trouble free service  
Your washer-dryer is a reliable companion in life and on the job. It is just as important for you to keep it in  
shape.  
Your washer-dryer is designed  
to provide reliable service over  
many years. A few simple steps  
will help to prolong its life and  
avoid problems. It is advisable,  
to turn off water taps when the  
machine is not to be used, this  
protects the hoses, etc.  
It is important to wash  
the detergent dispenser  
regularly.  
To prevent dried washing  
powder from  
accumulating, place the  
dispenser under running  
water for a few minutes.  
If the water in your area is too  
hard, use a deliming product  
(water is hard if it often leaves  
Never exaggerate with doses.  
Normal detergents already  
contain deliming agents. Only if  
the water is particularly hard,  
that is, rich in lime content, do  
we recommend the use of a  
specific product at every wash.  
A periodical wash cycle with a  
dose of a deliming product,  
without detergents or washing,  
may prove useful.  
Never use too much detergent  
or additives because this could  
cause an excess amount of  
foam, scaling and possible  
damage to the component parts  
of your washer-dryer.  
whitish stains around taps or  
drains, especially of bath tubs.  
For more accurate information as  
to the type of water in your  
system, call the local water  
works or a local plumber).  
Pockets must always be  
emptied removing even pins,  
badges and any other hard  
object.  
The washer-dryer exterior  
should be cleaned with a rag  
dipped in lukewarm water and  
soap.  
Do not forget to empty all pockets: small objects can  
cause damage to your washer-dryer.  
When in need, check the pump and the rubber hose.  
The washer-dryer comes equipped with a self-cleaning pump that does not require any cleaning or maintenance.  
Small objects may accidentally fall into the pump: coins, hair clips, loose buttons and other small items. To avoid  
possible damage, they are withheld in an accessible pre-chamber, situated at the lower end of the pump.  
Attention: Before attempting to examine this pre-chamber, first  
ensure that the machine has finished its programme and is empty.  
Unplug the machine, as with any maintenance.  
To gain access gently ease down the top of the plinth panel situated at  
the base of the machine, with a screwdriver etc, to release it. Then  
ease the top edge forward to allow it to be lifted clear (Fig. 1). Place  
a shallow dish or tray below the cover of the pre-chamber to catch  
the small amount of water present. Release the cover by turning anti-  
clockwise (Fig. 2). Ensure that the cover is securely replaced.  
Fig. 1  
The water inlet hose  
Fig. 2  
Re-fit the plinth cover by inserting the hooks on its lower edge into  
the slots and ease the top edge back into position.  
Check the rubber hose at least once a year. If you see any cracks, replace it immediately. When you use your washer-dryer,  
water pressure is very strong and a cracked tube could easily split open.  
13 Instructions for installation and use  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important for the safe use of your washer-dryer  
Your safety and that of  
Your washer-dryer has been built in compliance  
with the strictest international safety regulations.  
To protect you and all your family.  
your family  
Read these instructions and all 7. Never open the detergent 9. While the appliance is  
that children do no touch  
it. Never force the washer-  
dryer door because this  
could damage the safety  
lock which prevents  
accidental opening when the  
nachine is working. Allow a  
few minutes at the end of the  
program for the lock to  
release.  
the information in this manual  
carefully:they are an important  
source, not only of numerous  
useful tips, but also of vital  
information on safety, use and  
maintenance.  
dispenser while the  
appliance is functioning;  
do not use hand wash  
detergent because the  
abundance of foam could  
damage its internal parts.  
functioning, do not touch  
the drain water as it could  
reach very high tempera-  
tures. The appliance door,  
during wash cycles, tends  
to become hot; ensure  
1. the machine should not be 8. Never pull on the supply  
installed in an outdoor  
environment, not even  
when a roof shelters the  
area, because it may be very  
dangerous to leave it  
exposed to rain and  
thunderstorms.  
cable or the washer-dryer to  
disconnect it from the wall  
socket: it is extremely  
dangerous.  
10. In case of malfunctioning,  
first close the water tap  
and unplug the appliance  
from the wall socket; do  
not under any circum-  
stances touch internal parts  
in order to attempt repairs.  
2. It must only be used by  
adults and exclusively for  
washing clothes following  
the instructions provided in  
this manual.  
I only want an authorised  
specialised technician with  
original Indesit spare parts!  
11. If you interrupt a Wash  
Programme before its  
end, then the water and  
clothes may be hot. The  
water level may also be  
above the door, see  
instruction for draining  
the machine before you  
open the door and handle  
with caution .  
3. Should it have to be moved,  
proceed with the help of two  
or three people and handle  
it with the utmost care.  
Never try to do this alone,  
because the appliance is  
very heavy.  
12. During theTumble Drying  
programme and at its end,  
the clothes and drum of  
the machine may be hot,  
handle with caution and  
do not touch the drum.  
4. Before loading the washer-  
dryer, make sure the drum  
is empty.  
5. Never touch the washer-  
dryer when barefoot or  
with wet or damp hands  
or feet.  
6. Never use extensions or  
multiple plugs, which are  
particularly dangerous in  
humid environments. The  
power supply cable must  
never  
be  
bent  
or  
dangerously compressed.  
How to change the power supply cable  
The power supply cable must only be replaced by one of our authorised Service Engineers.  
Instructions for installation and use 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stay in touch  
THANK YOU for choosing an Indesit appliance. We are confident  
you have made a good choice and that your new appliance will give  
many years of excellent service.  
And we're there when you need us.  
Register your purchase  
now  
This will confirm your entitlement to enter our quarterly prize draw  
where you have the possibility to recover the cost of your purchase.  
Simply complete and return the Registration Form supplied with the  
appliance documents, using the FREEPOST envelope supplied. Or  
call the Registration Hotline on 0870 010 4305.  
We're as close to you as your telephone  
For direct access to Genuine Indesit Spare Parts and Accessories,  
call 0870 558 5850 and speak to our skilled staff who can help you to identify and purchase the item you require.  
For a Rapid Response to a problem with your appliance, call 0870 607 0805. We're open from Monday to  
Saturday (8am - 5.30pm weekdays, 9am - 5pm Saturday). We have our own department of highly trained Indesit  
service staff. For most calls, our Service Engineer can fix the problem on the first visit.  
Please have the following details to hand when you ring us:  
The nature of the problem, the Model Number and the Serial Number.  
These numbers can be found on the appliance and on the portion of the Registration Card which you retain.  
15 Instructions for installation and use  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instructions for installation and use 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17 Instructions for installation and use  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instructions for installation and use 18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Merloni Elettrodomestici  
Viale Aristide Merloni 47  
60044 Fabriano  
Italy  
Tel +39 0732 6611  
Fax +39 0732 662501  
Leader for young Europe  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Clothes Dryer TCD980 User Manual
Ingersoll Rand Sander 311A User Manual
Intel Computer Hardware ATC6430M User Manual
Jackson Model Vehicle Chemical Sanitizing Glasswasher Dishmachine Series User Manual
JobSite Systems Speaker LST CTR User Manual
Kidde Carbon Monoxide Alarm 9CO5 LP User Manual
KitchenAid Food Processor KFP1330 User Manual
Kodak Digital Camera C 503 User Manual
Kompernass Bread Maker KH 1122 User Manual
Konica Minolta Digital Camera e mini User Manual