Instructions for use
WASHER-DRYER
!
This symbol reminds you to read this instruction manual.
GB
GB
Contents
English,1
Installation, 2-3-4-5
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 6
Cutting off the water and electricity supplies
Cleaning the washer-dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
PWDE 8147 S
Precautions and advice, 7
General safety
Disposal
Description of the washer-dryer, 8-9
Control panel
Display
How to run a wash cycle or a drying cycle, 10
Wash cycles and options, 11
Table of wash cycles
Wash options
Detergents and laundry, 12
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Troubleshooting, 13-14
Assistance, 15-16
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the drain hose
Connect the drain
• the supply voltage is included within the values
indicated on the Technical Data Plate fixed on
the machine.
GB
hose, without bending
it, to a draining duct or
a wall drain situated
between 65 and 100
cm from the floor;
• the socket is compatible with the washer-
dryer’s plug. If this is not the case, replace the
socket or the plug.
65 - 100 cm
Your appliance is now supplied with a 13 amp
fused plug it can be plugged into a 13 amp
socket for immediate use. Before using the
appliance please read the instructions below.
The drain hose may
be connected to
an under-sink trap.
Before connecting
the drain hose from
the machine ensure
that any blanks or
removable ends have
been taken off the
spigot.
WARNING-THISAPPLIANCEMUSTBEEARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be
used, and the fuse cover re-fitted. If the fuse
cover is lost, the plug must not be used until a
replacement is obtained.
Where it connects to
the waste water pipe
cut end off spigot or
remove the blanking cap
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words
on the base of the plug. Replacements can be
obtaineddirectlyfromyournearestServiceDepot.
If it is placed over the
edge of a basin or sink
be sure the free end of
the hose should not
be underwater.
Removing the plug:
If your appliance has a non-rewireable moulded
plug and you should wish to re-route the mains
cable through partitions, units etc., please
ensure that either:
the plug is replaced by a fused 13 ampere
rewireable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13
amp cable outlet, controlled by a switch, (in
compliance with BS 5733) which is accessible
without moving the appliance.
! We advise against the use of hose extensions; in
caseofabsoluteneed,theextensionmusthavethe
same diameter as the original hose and must not
exceed 150 cm in length. Ensure that if the drain
hose is pushed into a standpipe, that the end does
notgodownmorethan15cms(6inches).Ifthehose
ispusheddowntoofar,thismaycausethemachine
to self -syphon ie. continuously empty as it is filling.
Disposing of the plug:
Ensure that before disposing of the plug itself,
you make the pins unusable so that it cannot be
accidentally inserted into a socket.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
Instructions for connecting cable to an alternative
plug:
• the socket is earthed and in compliance with
the applicable law;
Important: the wires in the mains lead are
coloured in accordance with the following code:
Green & Yellow Earth
• the socket is able to sustain the appliance’s
maximum power load indicated on the Technical
Data Plate fixed on the machine;
Blue
Brown
Neutral
Live
3
Download from Www.Somanuals.com. All Manuals Search And Download.
As the colours of the wires in the lead may
not correspond with the coloured markings
identifying the terminals in your plug, proceed
as follows:
! The power supply cable must only be
GB
replaced by an authorised serviceman.
Warning! The company denies all liability if and
when these norms are not respected.
Connect Green & Yellow wire to terminal
marked E or or coloured Green or Green &
Yellow.
The first wash cycle
Connect Brown wire to terminal marked L or
coloured Red.
Connect Blue wire to terminal marked N or
coloured Black.
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle 1.
If a 13 amp plug (BS 1363) is used it must be
fitted with a 13 amp fuse, either in the plug or
adaptor or at the distribution board.
If you are in any doubt regarding the electrical
supply to your machine, consult a qualified
electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE
NEUTRAL (N)
LIVE (L)
EARTH (E)
BROWN
GREEN & YELLOW
GREEN &
YELLOW
13 ampere fuse
BROWN
CROSS-BAR
CORD GRIP
BLUE
Disposing of the appliance:
When disposing of the appliance please
remove the plug by cutting the mains cable
as close as possible to the plug body and
dispose of it as described above.
! The washer-dryer should not be installed
in an outdoor environment, not even where
the area is sheltered, because it may be very
dangerous to leave it exposed to damp, rain
and thunderstorms.
! When the washer-dryer is installed, the mains
socket must be within easy reach.
! Do not use extensions or multiple sockets.
! The power supply cable must never be bent
or dangerously compressed.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
GB
Model
PWDE 8147 S
width 59.5 cm
Dimensions height 85 cm
depth 60 cm
from 1 to 8 kg for wash
programme
Capacity
Electrical
from 1 to 6 kg for the drying
programme
please refer to the technical
connections data plate fixed to the machine
maximum pressure
1 MPa (10 bar)
Water con-
minimum pressure
nections
0.05 MPa (0.5 bar)
drum capacity 62 litres
up to 1400 rotations per
minute
Spin speed
wash: programme 1; tem-
perature 60°C; using a load
of 8 kg.
Energy ra-
ted
drying: the smaller load
must be dried by selecting
programmes the “A1” (IRON) dryness le-
according to vel. The load must consist of
regulation
EN 50229
2 sheets, 1 pillowcase and
1 hand towel; the remainder
of the load must be dried by
selecting the “A4” (EXTRA)
dryness level.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2002/96/EC
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
To access the pre-chamber:
Cutting off the water and
electricity supplies
GB
1. Take off the cover
panel on the front
of the machine by
first pressing it in
the centre and then
pushing downwards
on both sides until
you can remove it
(see figures).
• Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system
inside the washer-dryer and help to prevent
leaks.
1
2
3
• Unplug the washer-dryer when cleaning it
and during all maintenance work.
Cleaning the washer-dryer
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.
2. Unscrew the lid
by rotating it anti-
clockwise (see figure):
a little water may
trickle out. This is
perfectly normal.
Cleaning the detergent dispenser
drawer
To remove the drawer,
1
press lever (1) and pull
the drawer outwards
(2) (see figure).
Wash it under running
water; this procedure
3.Clean the inside thoroughly.
4.Screw the lid back on.
2
should be repeated
5.Reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
frequently.
Checking the water inlet hose
Caring for the door and drum of
your appliance
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
• Always leave the porthole door ajar in order
to prevent unpleasant odours from forming.
Cleaning the pump
! Never use second-hand hoses.
The washer-dryer is fitted with a self-
cleaning pump which does not require any
maintenance. Sometimes, small items (such
as coins or buttons) may fall into the protective
pre-chamber at the base of the pump.
! Make sure the wash cycle has finished and
unplug the appliance.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and tips
! This washer-dryer was designed and constructed in
accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
Disposal
GB
• Disposing of the packaging materials:
observe local regulations so that the packaging may be
re-used.
• The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
using the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the materials
inside the machine, while preventing potential damage
to the atmosphere and to public health. The crossed-out
dustbin is marked on all products to remind the owner of
their obligations regarding separated waste collection.
For more information relating to the correct disposal of
household appliances, owners should contact their local
authorities or appliance dealer.
General safety
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
• Do not dry unwashed items in the tumble dryer.
Items that have been soiled with substances such
as cooking oil, acetone, alcohol, petrol, kerosene,
spot removers, turpentine, waxes and wax removers
should be washed in hot water with an extra amount of
detergent before being dried in the tumble dryer.
Items such as foam rubber (latex foam), shower caps,
waterproof textiles, rubber backed articles and clothes or
pillows fitted with foam rubber pads should not be dried
in the tumble dryer.
Fabric softeners, or similar products, should be used as
specified by the fabric softener instructions. The final part
of a tumble dryer cycle occurs without heat (cool down
cycle) to ensure that the items are left at a temperature
that ensures that the items will not be damaged.
WARNING: Never stop a tumble dryer before the end of the
drying cycle unless all items are quickly removed and spread
out so that the heat is dissipated.
• This appliance was designed for domestic use only.
• Do not touch the machine when barefoot or with wet or
damp hands or feet.
• Do not pull on the power supply cable when unplugging the
appliance from the electricity socket. Hold the plug and pull.
• Do not open the detergent dispenser drawer while the
machine is in operation.
• Do not touch the drained water as it may reach
extremely high temperatures.
• Never force the porthole door. This could damage the safety
lock mechanism designed to prevent accidental opening.
• If the appliance breaks down, do not under any
circumstances access the internal mechanisms in an
attempt to repair it yourself.
• Always keep children well away from the appliance while
it is operating.
• The door can become quite hot during the wash cycle.
• If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Before loading laundry into the washer-dryer, make sure
the drum is empty.
• During the drying phase, the door tends to get quite hot.
• Do not use the appliance to dry clothes that have
been washed with flammable solvents (e.g.
trichlorethylene).
• Do not use the appliance to dry foam rubber or
similar elastomers.
• Make sure that the water tap is turned on during
the drying cycles.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the washer-dryer
Control panel
GB
OPTION
DOOR
buttons and
TEMPERATURE
ON/OFF
indicator lights
LOCKED
button
button
indicator light
DISPLAY
WASH
SPIN
DRY
CYCLE
Detergent dispenser drawer
START/PAUSE
button and indicator
light
button
button
SELECTOR
KNOB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
START/PAUSE
button and indicator light: when the
blue indicator light flashes slowly, press the button to start
a wash cycle. Once the cycle has begun the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
amber colour. If the symbol is not illuminated, the door
may be opened (wait approximately 3 minutes). To start
the wash cycle from the point at which it was interrupted,
press the button again.
ON/OFF
button: press this briefly to switch the
machine on or off. The START/PAUSE indicator light
which flashes slowly in a blue colour shows that the
machine is switched on. To switch off the washer-dryer
during the wash cycle, press and hold the button for
approximately 3 seconds; if the button is pressed briefly
or accidentally the machine will not switch off.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent
any damage, wait until the symbol turns off before opening
the door (wait approximately 3 minutes).
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of programmes and wash
cycles”).
To open the door while a cycle is in progress, press the
START/PAUSE button; if the DOOR LOCKED symbol is
switched off the door may be opened.
OPTION buttons and indicator lights: press to select
the available options. The indicator light corresponding to
the selected option will remain lit.
Standby mode
This washer-dryer, in compliance with new energy saving
regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
SPIN
button: press to reduce or completely exclude
the spin cycle; the value appears on the display.
Consumption in off-mode: 0,5 W
TEMPERATURE
button: press to reduce or
Consumption in Left-on: 0,5 W
completely exclude the temperature; the value appears
on the display.
DRYING button
: press to decrease or exclude
drying; the selected drying level or time will appear on the
display (see “How to run a wash cycle or a drying cycle”).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
GB
B
A
C
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED
START option has been set, the countdown to the start of the selected wash cycle will appear.
Furthermore, pressing the corresponding button allows you to view the maximum temperature, spin speed and drying level
or time values attained by the machine during the selected cycle.
The hour-glass flashes while the machine is processing data, depending on the wash cycle and
level selected. After
a maximum of 10 minutes, the “hour-glass” icon remains lit in a fixed manner and the final amount of time remaining is
displayed. The hour-glass icon will then switch off approximately 1 minute after the final amount of time remaining has
appeared.
The phases scheduled for the selected cycle and, once the cycle has begun, the current phase of the wash cycle (and drying
cycle, if applicable) appear in section B:
Main wash
Rinse
Spin/Drain
Drying
The icons corresponding to “temperature”, “spin” and “drying” (working from the left) are displayed in section C.
The “temperature” bars
The “spin” bars
indicate the maximum temperature level which may be selected for the set cycle.
indicate the maximum spin level which may be selected for the set cycle.
The
symbol lights up while the drying settings are being adjusted.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
How to run a wash cycle or a
drying cycle
1. SWITCH THE MACHINE ON. Press the
button;
If your laundry load to be washed and dried is much
greater than the maximum stated load (see adjacent
table of programmes), perform the wash cycle, and
when the cycle is complete, divide the garments into
groups and put some of them back in the drum. At this
point, follow the instructions provided for a “Drying
only” cycle. Repeat this procedure for the remainder of
the load.
GB
the START/PAUSE indicator light will flash slowly in a
blue colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
A cooling-down period is always added to the end of
each drying cycle.
Drying only
Use the cycle selector knob to select a drying cycle
(11-12-13) in accordance with the type of fabric. The
desired drying level or time may also be set using the
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
DRYING button
.
Modify the cycle settings.
• Press the button to enable the option; the indicator light
corresponding to the button will switch on.
• Press the button again to disable the option; the
indicator light will switch off.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! If the selected option is not compatible with
a previously selected one, the indicator light
corresponding to the first function selected will flash and
only the second option will be activated; the indicator
light for the option which has been activated will be
illuminated.
Modify the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the
button, until it is completely excluded
Note: if the
option has been selected, none of the
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
incompatible options may be activated.
! The options may affect the recommended load value
and/or the duration of the cycle.
Setting the drying cycle
The first time the button
is pressed, the machine
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn blue, remaining lit in a fixed manner, and the door
will be locked (the DOOR LOCKED symbol will be lit).
To change a wash cycle while it is in progress, pause
the washer-dryer using the START/PAUSE button
(the START/PAUSE indicator light will flash slowly in an
amber colour); then select the desired cycle and press
the START/PAUSE button again. To open the door while
a cycle is in progress, press the START/PAUSE button;
if the DOOR LOCKED symbol is switched off the door
may be opened (wait approximately 3 minutes). Press
the START/PAUSE button again to restart the wash
cycle from the point at which it was interrupted.
will automatically select the maximum drying cycle
which is compatible with the selected wash cycle.
Subsequent presses will decrease the drying level
and then the drying time, until the cycle is excluded
completely (“OFF”). If these buttons are pressed again,
the maximum values are restored.
Drying may be set as follows:
A- Based on the desired laundry dryness level:
Iron: suitable for clothes which will need ironing
afterwards. the remaining dampness softens creases,
making them easier to remove. “A1” appears on the
display.
Hanger: ideal for clothes which do not need to be dried
fully. “A2” appears on the display.
Cupboard: suitable for laundry which can be put back
in a cupboard without being ironed. “A3” appears on
the display.
Extra: suitable for garments which need to be dried
completely, such as sponges and bathrobes. “A4”
appears on the display.
B - Based on a set time period: between 30 and 180
minutes (Max. load 4 kg).
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may be
opened (wait approximately 3 minutes). Open the door,
unload the laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the
button. The cycle will be stopped
and the machine will switch off.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash cycles and options
Table of wash cycles
GB
Detergents
Max.
Max.
Max. load Cycle
Description of the wash cycle
temp. speed Drying
(°C)
(kg)
duration
Fabric
(rpm)
Main wash
softener
Daily Programmes
1
1
1
2
3
4
5
6
7
White Cotton: extremely soiled whites.
White Cotton (1): heavily soiled whites and resistant colours.
White Cotton (2): lightly soiled whites and delicate colours.
Cotton: heavily soiled whites and resistant colours.
Coloured Cotton (3): lightly soiled whites and delicate colours.
Synthetics: lightly soiled resistant colours.
Jeans
90°
60°
40°
60°
40°
40°
40°
40°
40°
1400
1400
1400
1400
1400
800
8
8
8
8
8
3.5
4
800
Shirts
600
2
Wool: for wool, cashmere, etc.
800
2
Special cycles
8
9
Delicates: for garments in silk and viscose, lingerie.
Duvet: for down-stuffed garments
30°
30°
0
-
-
2
3
1000
Max.
2 pairs
10 Sport Shoes
30°
600
-
Dry cycles
11 Cotton
-
-
-
-
-
-
-
-
-
-
-
-
6
3.5
2
12 Synthetics
13 Wool
Partial cycles
Rinse
-
-
-
1400
1400
0
-
-
-
-
-
8
8
8
Spin
Drain
-
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors
such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 50229: select wash cycle 1 with a temperature of 60°C.
2) Long wash cycle for cottons: select wash cycle 1 with a temperature of 40.
3) Short wash cycle for cottons: select wash cycle 3 with a temperature of 40.
EASY IRON and START/PAUSE indicator lights will flash. To
drain the water so that the laundry may be removed, press
Wash options
the START/PAUSE button or the EASY IRON button.
The “PRIME” technology optimises energy, water and time
consumption according to the quantity of garments actually
! It cannot be used in conjunction with wash cycles 7, 10,
11, 12, 13,
,
,
.
inserted in the machine. Moreover, pressing the
allows for selecting the following options:
button
Note: If you also want to run the drying cycle, this option is
enabled only if combined with level “A1” (Iron dry).
- Water: allows for reducing water consumption without
having to renounce impeccable results (recommended for
heavily soiled garments).
- Energy: automatically selected by “PRIME”, this option
reduces energy consumption (recommended for normally
soiled garments).
Cool Wash
The Cool Wash function saves energy by not heating the
water used to wash your laundry – an advantage both to the
environment and to your energy bill. Instead, intensified wash
action and water optimisation ensure great wash results in the
same average time of a standard cycle. For the best washing
results we recommend the usage of a liquid detergent.
! It cannot be used in conjunction with wash cycles
- Time: allows for reducing wash cycle duration
(recommended for lightly soiled garments).
! This may only be used in conjunction with wash cycles 1, 2,
3, 4 (all three levels) and 5, 6 (Energy and Time levels).
6, 7, 8, 9, 10, 11, 12, 13,
,
,
.
Delay Timer
Easy iron
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option is enabled, the
By selecting this function, the wash and spin cycles will be modified
in order to reduce the formation of creases. At the end of the cycle
the washer-dryer will perform slow rotations of the drum, while the
EASY IRON and START/PAUSE indicator lights will flash (blue and
orange respectively). To end the cycle, press the START/PAUSE
button or the EASY IRON button. For wash cycles number 8,
the machine will end the cycle while the laundry is soaking; the
corresponding indicator light
will remain lit. To remove
the delayed start setting, press the button until the text
“OFF” appears on the display.
! This option can be used in conjunction with all cycles.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergents and laundry
Detergent dispenser drawer
GB
Successful washing results also depend on the correct
In UK, Eire, Hong Kong and India the Woolmark trade
mark is a Certification trade mark.
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
Delicates: use special wash cycle 8 to wash all silk
garments. We recommend the use of special detergent
which has been designed to wash delicate clothes.
Curtains: we recommend you fold the curtains and place
them in a pillow case or mesh bag. Use wash cycle 8.
Duvet: to wash double or single duvets (the weight
of which should not exceed 3 kg), cushions or clothes
padded with goose down such as puffa jackets, use the
special wash cycle number 9 “Duvet”. We recommend
that duvets are placed in the drum with their edges folded
inwards (see figure) and that no more than ¾ of the total
volume of the drum is used.
! Do not use hand washing detergents; they create too
much foam.
Open the detergent
dispenser drawer and pour
in the detergent or washing
additive, as follows.
C
B
A
To achieve the best results, we recommend that a
liquid detergent is used and placed inside the detergent
dispenser drawer.
Compartment A: Washing detergent (powder or
liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
Compartment B: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Extra compartment C: we recommend this
compartment is used for liquid detergent.
Preparing the laundry
• Divide the laundry according to:
Sport Shoes (wash cycle 10): is for washing sports
shoes; for best results, do not wash more than 2 pairs
simultaneously.
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
• Do not exceed the values listed in the “Table of wash
cycles”, which refer to the weight of the laundry when dry.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washer-dryer performs the
distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special wash cycles
Jeans: turn the garments inside out before washing and
use liquid detergent. Use wash cycle 5.
Shirts: use special wash cycle 6 to wash shirts in various
fabrics and colours.
It guarantees maximum care is taken of the garments and
minimises the formation of creases.
Wool: the wool wash cycle of this machine has been
tested and approved by The Woolmark Company for the
washing of wool containing garments labelled as “hand
wash” provided that the garments are washed according
to the instructions on the garment label and those issued
by the manufacturer of this washer-dryer. (M1127)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make
sure that the problem cannot be solved easily using the following list.
GB
Problem:
The machine does not switch on.
Possible causes / Solutions:
• The appliance is not plugged into the socket fully, or not enough to make contact.
• There is no power to the socket, or the fuse has blown in the mains plug.
The wash cycle does not start.
• The door is not closed properly.
• The ON/OFF button has not been pressed.
• The START/PAUSE button has not been pressed.
• The water tap has not been turned on to allow water to flow into the machine.
• A delayed start has been set.
The machine does not dry.
• Check the 2 sections above.
• The ‘DRY’ button has been pressed to exclude drying.
The clothes are too hot when the
drying cycle is finished.
• A cooling-down period is always added to the end of each drying cycle. If the
clothes appear too hot to handle leave the door open to allow to cool further
before removing from the machine.
The machine does not fill with
water or ‘H20’ flashes on the
display.
• The water inlet hose is kinked.
• The water inlet hose is not connected to the water supply.
• The water pressure is too low.
• The water tap has not been turned on to allow water to flow into the machine.
• There is no water supply to the house.
• The inlet valve filter is blocked.
• The START/PAUSE button has not been pressed.
The machine continuously fills with • The top of the drain hose is too low - It must be fitted at a height between 65
water and continually drains away
or Water left in the drum
or Stuck on wash.
and 100 cm from the floor (see “Installation”).
• The drain hose is connected incorrectly to the sink trap allowing water to run
into the machine, the drain hose must be positioned higher than the bottom of
the sink to prevent water flowing down the drain hose.
• The end of the drain hose has been pushed too far down the standpipe, the
‘U’ bracket should be fitted 100 mm from the end of the drain hose.
The machine does not drain or spin • The Pump filter is blocked.
(error lights flashing).
• The drain hose is kinked (see “Installation”).
• New Installation - The blanking cap or spigot has not been removed if
connected under a sink.
• The drain hose or sink trap is blocked.
The machine does not spin.
• The Spin Speed is set to zero.
The machine does not drain or spin • If the ‘EASY IRON’ option is enabled, at the end of the program the machine
- ‘EASY IRON’ & ‘START/PAUSE’
indicator lights flash.
drum will rotate slowly. To complete the program press the ‘START/PAUSE’ or
the ‘EASY IRON’ buttons.
• If the ‘DELICATES’ programs are selected, at the end of the program it requires the
drain phase to be started. To complete the program press the ‘START/PAUSE’ or
the ‘EASY IRON’ buttons.
The wash programme takes too
long.
• Programme times will vary due to water pressure, the incoming water temperature
and if the wash load goes out of balance. This will increase the programme times
accordingly (see ‘ The machine wont spin properly’ below) - (Most Common Cause!).
The machine vibrates a lot during
the spin cycle.
• The feet have not been adjusted, enabling the machine to rock.
• New Installation - Either the Transit Bolts including the plastic spacers, or the
Polystyrene Packaging have not been removed when installing the machine.
• The machine is trapped between cabinets and/or walls.
• The load is in a slight out of balance condition and machine is spinning, but at
a lower speed.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
The Display sticks at one ‘time to
end’ for more than 1 Minute or
the Display changes the estimated
‘Time to End’ during the programme.
• The display time is for guidance only - it is not a precise time to finish
and may vary.
GB
The machine is noisy.
• There will always be some motor, pump and drum noise during spin.
The machine wont spin properly.
• Out of Balance detected when attempting to go into a spin cycle - If this
happens the machine will continue to try to repeat the distribution of the load
required before the machine will go into higher spin speeds - This will increase
the programme time accordingly. This is a safety feature to prevent damage.
Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,
etc). - Try the programme again using a different load.
The machine leaks from the
dispenser.
• The dispenser drawer is blocked with detergent and requires cleaning.
• The water pressure is too high and requires turning down - turn down the tap
on the water supply pipe slightly and try again.
• The machine is tilting forwards - It must be level when in its final position.
The machine leaks (other than
dispenser).
• The fill hose is loose, check both the cabinet and tap ends.
• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill
hose is missing the rubber washer.
• The drain hose is not fixed in properly.
The option lights and the START/
PAUSE indicator light are flash
rapidly and an error code appears
on the display (eg F-01, F-..).
• Switch off the machine and unplug it, wait for approximately 1 minute and then
switch back on again. If the problem persists contact Technical Assistance
Centre.
The machine smells.
• The machine requires a service wash. Run a 90 degree wash cycle with
detergent and no laundry.
The machine door cannot be
opened.
• The door will not open until the door lock indicator light goes out shortly after
the program has finished.
• If there is no power to the machine you need to perform the manual unlocking
procedure.
Door Seal damaged at the bottom.
• The door seal has drainage holes at the bottom - This is normal.
• The water level is correct if it can be seen at the bottom of the door.
The water level is too low when
the machine is washing.
The word ‘dON’ appears in the
display window and the drum
slowly turns.
• To exit, switch machine off, then press and hold ‘ON/OFF’ and ‘START/PAUSE’
buttons simultaneously for 3 seconds until ‘dof’ appears. Note the machine will
need the language resetting.
There is too much foam.
• The detergent is not suitable for machine washing (it should display the text
‘for washer-dryers’ or ‘hand and machine wash’ or the like).
• Too much detergent was used - less detergent is required in soft water.
After completing the programme,
or before starting a programme,
the machine has turned itself off
(no lights).
• To comply with new energy saving regulations the machine is fitted with an
automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate
the machine, it can then either be switched off or a new programme selected.
General.
• Your washer-dryer contains sensors that monitor progress during the wash cycle
(eg: Water Levels, Temperatures, Out of Balance loads, Wash time/progress).
Normally, if your machine successfully completes the cycle, there is unlikely to
be anything wrong!
Remember, you will be charged for a service call for problems caused by incorrect installation, as listed above.
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.
Do not wash items which do not have a wash label, or wash items that are not intended as machine washable.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Assistance
12 Months Parts and Labour Guarantee
GB
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve
months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
Replacement of any consumable item or accessory . These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR
NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Indesit also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering your appliance
with us and the parts being fitted by one of our authorised engineers. There will be a charge for our engineer’s time. To
activate the extra parts warranty on your appliance, simply call our registration line on 08448 24 24 24 (Republic of
Ireland 01 230 0800).
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills for the
life of your policy. To find the ideal plan for you please call our advice line on
08448 226 226 (Republic of Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any technical
difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08448 224 224 (Republic of
Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an engineer to call.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
195106514.00
08/2012
-
Xerox Fabriano
After Sales Service
GB
No one is better placed to care for your Indesit appliance during the course of its working life than us - the manufacturer.
Essential Contact Information
Indesit Service
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified
engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean your
appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Indesit ownership. To activate your free 5 year parts guarantee you must register
your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling & Disposal Information
As part of Indesit’s continued commitment to helping the environment, Indesit reserves the right to use quality, recycled
components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door, plug and
cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the appliance can no longer
be plugged into a mains socket, and the door cannot be locked shut.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|