Indesit
HI561 IXUK
HI591 IXUK
Commercial Codes
28113 + 28114
Instruction Booklet
Aura
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION .......................................................................................................................... 4
Safety warnings .................................................................................................................................... 4
Components ......................................................................................................................................... 4
Instructions for Installation ................................................................................................................... 5
Fixing the wall brackets (and splashback) .................................................................................... 5
Fixing the canopy hood ................................................................................................................. 6
Ducting or Recirculation fitting....................................................................................................... 7
Electrical connection and working test .......................................................................................... 8
Fitting the telescopic chimney stack .............................................................................................. 8
USE
9
Safety warnings .................................................................................................................................... 9
Instruction for Use ................................................................................................................................ 9
MAINTENANCE........................................................................................................................ 10
Metal grease filters ............................................................................................................................. 10
Charcoal filters ................................................................................................................................... 10
Worktop illumination ........................................................................................................................... 11
Cleaning ............................................................................................................................................. 11
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
This canopy hood is designed to be fixed to any rigid vertical surface, over a gas or
electric hotplate and can be used either in the extraction mode (ducted to the outside) or
in the recirculation mode (internal recycling).
Safety warnings
• Before commencing the installation, consideration should be given to the difficulties
to be found during installation and to the bulky weight of the hood. The installation
work must be undertaken by a qualified and competent person in conformity to the
rules concerning the evacuation of contaminated air. The manufacturer disclaims all
liability for any damage or injury caused as a result of not following the instructions
for installation contained in the following text.
• When used in the extraction mode the cooker hood ducting must not be connected to
a flue which is used for exhausting fumes from appliances supplied with energy other
than electric such as a central heating flue or water heating flue.
• When istalled, the hood must be positioned at least 65 cm above a cooking appliance.
• Never do flambé cooking under this cooker hood.
• Never leave frying pans unattended during use as overheated fats and oils may catch
fire.
• If the room where the cooker hood is to be used contains a fuel burning appliance
such as a central heating boiler then this must be of the room sealed or balanced flue
type. If other types of flue or appliance are fitted ensure that there is an adequate
supply of air into the room. When the cooker hood is used in conjunction with other
appliances supplied with energy other than electric, the negative pressure in the room
must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the
cooker hood.
2
S
Components
The cooker hood is made up of the following
components (fig 1):
• n. 1 hood canopy C complete with controls,
lighting and fan motor.
1
A
I
• n. 1 telescopic chimney stack formed by:
n. 1 U-shaped upper section item S
n. 1 U-shaped lower section item I
• n. 1 reduction flange Ø 150-120 A
• n. 1 recirculation spigot item R
• n. 1 deflector D (special versions only)
• n. 1 plastic bag containing:
C
R
D
n. 1 wall brackets 1 to fix the canopy hood
n. 2 wall brackets 2 to fix the chimney, rawl
plugs, screws, and documentation
• n. 1 splashback B (optional)
B
Fig. 1
4
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions for Installation
For easy installation proceed as follows:
• Fix the wall brackets and Splashback.
• Fix the canopy.
• Set the hood for recirculation or evacuation.
• Connect the hood to the mains supply and ensure that it works properly.
• Fix the telescopic metal frame.
Fixing the wall brackets (and splashback)
Ref. to Fig. 2a-b
• Draw a vertical line on the wall, from the centre of the cooking appliance up to the ceiling,
using a marking pen. This is to ensure the correct vertical alignment of many components.
Fixing the wall brackets 1:
• Put the bracket I to the wall, aligning its marked centre across the vertical line, ensuring
that the distance between the centres of the holes and the cooking area is as follows:
• Draw a horizontal line on the wall ensuring that the distance from the cooktop is as
follows:
a) when the splasback is to be installed: d = 270 mm + H, where H is the height of the
visible part of the splashback; as the splashback can be of different heights, the correct
H figure can only be obtained by measuring the actual height of the splashback to be
fitted.
b) without splashback d = 875 mm minimum.
243_A02
2
1
2
1
Fig. 2
115
115
140
140
B
B
b
a
GB
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: ensure that the wall bracket (I) is levelled. The hood can be aligned or adjusted
in height by rotating the adjustment screws (see below).
• Mark on the wall the centres of the two keyholes of the bracket.
Fixing the wall brackets item 2:
• Place one of the two brackets (item 2 fig. 1) 15 mm from the ceiling or from a horizontal
line drawn between the top of the adjoining wall cabinets, ensuring that the bracket is
level and mark the centres for the keyhole bracket fixing screws.
• Place the other wall bracket (item 2 fig. 1) on the wall at “X” distance. This measurement
should be determined by the height of the upper chimney stack and mark the centres for
the keyhole bracket fixing screws.
• Pilot drill all the hole positions as marked on the wall using an 8 mm drill and fix the wall
brackets 1-2 using the rawl plugs and screws supplied.
Splashback (optional)
When a splashback is to be fitted, the distance between the cooker hood and the cooking
appliances will be determined by the height of the splashback, item B. The splashback is
to be installed before installing the canopy. If the splashback is to be fixed to the wall
using both the top and bottom fixing holes care must be taken to ensure that the
splashback is fitted at the correct height before fixing it into position. The fitting should
be undertaken by a a competent person with experience in this type of installation. If the
splashback is to be fixed through only the top fixing holes proceeds as follows:
• Put the splashback on the worktop as illustrated in fig. 2a; then holding it against the wall
to ensure that it is correctly positioned mark the holes for the top fixing screws on the
wall.
• Pilot drill the wall using an 8 mm drill and fix the splashback using the 8 mm rawl plugs
and screws supplied.
• If the fixing holes in the bottom of the splashback are not to be used to secure the
splashback to the wall the installer should ensure that the bottom edge is tucked down
behind the rear of the worktop.
Fixing the canopy hood
• Adjust the two screws V (on the canopy
connection points) to approximately
half way.
• Hook the rear of the canopy to the wall
bracket 1, after anchoring the latter to
the wall.
Fig. 3
• Turn the screws V to adjust the canopy
vertically and level it horizontally.
• Fit and lock the central fixing screw V1
(provided) to lock the canopy in place
(fig.3).
6
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Ducting or Recirculation fitting
Ducting fitting
• The cooker hood can be ducted to the outside using
either rigid or flexible fire retardant ducting of 120 or
150 mm. The choice is left to the installer. When 120
mm ducting is to be used it will be necessary to install
the reduction flange item A on the air outlet fig. 4.
• The installer should provide suitable ducting and sealing
material for the installation.
A
• The cooker hood can also be ducted to the outside
through one of the rectangular openings located in either
side of the lower section of the chimney stack. In this
case the deflector (item D) should be fitted into the
spigot (item R) to close the aperture which is not used
(fig. 5).
Fig. 4
• If the hood is provided with the charcoal filters fitted,
the filters should be removed (see paragraph
Maintenance).
A
Recirculation fitting
• The filtered air is returned to the room through the two
side grilles on U-shaped lower section I, which are either
formed in the metal itself (fig. 6).
• Fit the recirculation spigot item R into the round outlet
on top of the canopy while pressing down on the spigot
until it snaps into position.
• Install the charcoal filters inside the canopy as instructed
in paragraph Maintenance).
R
D
Fig. 6
Fig. 5
R
243_A05
GB
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection and working test
• Before connecting to the mains supply ensure that the mains voltage corresponds
with the voltage on the rating plate inside the hood.
• Connect the cooker hood to the mains via a double pole switch which has 3 mm
clearance between the contacts.
• The appliance must be earthed.
• Once the electrical connection has been completed, check that worktop illumination,
motor and speed work properly.
Fitting the telescopic chimney stack
• Fit the two plastic supports provided to the top part of the hood.
• To fit the upper section item S first expand the chimney slightly to allow it to fit over the
wall brackets (item 2 fig. 1) and then secure the upper section using the 4 screws supplied.
• The lower section item I of the chimney stack should be fitted between the lower bracket
2 and the wall.
• Fix the U-shaped section to the plastic supports, using two of the screws provided in the
bag of accessories (fig. 7).
Part 2a
OPERATION AND MAINTENANCE INSTRUCTIONS
S
Fig. 7
I
8
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
USE
Safety warnings
• Before carring out any kind of maintenance or cleaning, disconnect the hood from the
mains supply.
• The grease filters and the charcoal filter should be cleaned or replaced as recommended
by the manufacturer or more frequently if the hood is used consistently over 4 hours
per day.
• When using a gas hob in connection with the cooker hood never leave the burners of
the hob uncovered while the hood is in use or when the pans have been removed.
Switch off the gas before removing the pan, or for just short periods and never leave
the hob unattended.
• Always ensure that the flame is kept at the correct intensity to prevent the flame from
licking round from the bottom of the pan; this will save energy and will avoid a
dangerous concentration of heat.
• Always ensure that the appliance is used in accordance with the manufacturer’s
instructions for the removal of contaminated air and odours during cooking.
Instruction for Use
Control panel
BUTTON T1
BUTTON T2
=
=
Turns the lighting system on and off;
Turns the on and off at low speed. This is ideal to obtain a particularly
silent but continuous flow of air when the level of cooking fumes is
low;
BUTTON T3
BUTTON T4
=
=
Medium speed, suitable for most normal operating conditions. This
gives an excellent ratio between treated air flow and noise level;
High speed, suitable to deal with heavy cooking fumes, even for long
periods of time.
T2
T3
T4
T1
2
3
GB
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Regular maintenance and cleaning will ensure good performance and reliability, while
extending the working life of the hood. Special attention should be paid to the grease
filters and to the charcoal filters when the hood is used in the recirculation mode.
Metal grease filters
Cleaning
The metal grease filter should be cleaned
every two months with normal usage and can
be cleaned in a dishwasher or by hand using
a mild detergent or liquid soap.
Replacement
• Remove the filters one at a time, pushing the
handle towards the rear of the hood (fig. 8).
Fig. 8
• When replacing, ensure that the handle faces
outwards.
ATTENTION - THERE COULD BE A
POSSIBLE FIRE HAZARD IF THE FILTERS
ARE NOT REPLACED ACCORDING TO
THESE INSTRUCTIONS.
Charcoal filters
Functioning
In the recycling mode the charcoal filters
absorb smells and odours. This hood is
designed to be fitted with two charcoal filters
on both sides of the fan unit (fig. 9). The
charcoal filter cannot be washed and should
be replaced at least every 4 months or more
frequently if the hood is used consistently.
Replacement
• To remove the charcoal filters place on hand
on one filter at a time and turn it toward the
front part.
• The charcoal filter can now be removed.
• Always ensure to replace both filters at the
same time.
Fig. 9
ATTENTION - THERE COULD BE A
POSSIBLE FIRE HAZARD IF THE FILTERS
ARE NOT REPLACED ACCORDING TO
THESE INSTRUCTIONS.
10
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Worktop illumination
Worktop illumination is provided by 2
40W bulbs.
To replace the lighting elements
proceed as follows:
• Remove the metal clips T.
Z
T
Z
T
• The glass diffuser is kept in position by
the retaining lugs Z.
• Pull the glass diffuser slightly to one
side until it disconnects from the lug on
the other side (arrow 1), then pull
slightly downwards (arrow 2) and slide
in the opposite direction (arrow 3) until
the glass diffuser can be removed.
• Replace the lamps or the neon strip
and replace the glass diffuser by
repeating the above operations in
reverse order (fig. 10).
Fig. 10
Cleaning
When cleaning the hood:
• Never use a wet cloth or sponge, or
running water.
• Never use thinners or products
containing alcohol, as they might
damage the paintwork.
• Never use abrasive cleaning materials,
in particular when cleaning stainless
steel surfaces.
It is recommended to use a damp
cloth and mild liquid household
cleaner.
GB
11
Download from Www.Somanuals.com. All Manuals Search And Download.
This appliance complies with European regulations on low voltages, EEC Directive 73/23 on
electrical safety, and with the following European regulations: EEC Directive 89/336 on
electromagnetic compatibility and EEC Directive 93/68 on EC marking.
436000718 01 020522
Download from Www.Somanuals.com. All Manuals Search And Download.
|