Indesit Dishwasher DIS 04 User Manual

Operating instructions  
DISHWASHER  
Contents  
EN  
Installation, 2-3-4  
Positioning and levelling  
English, 1  
Connecting the water and electricity supplies  
Advice regarding the first wash cycle  
Technical data  
Electrical connection  
Description of the appliance, 5  
Overall view  
Control panel  
Loading the racks, 6  
Lower rack  
Cutlery basket  
Upper rack  
DIS 04  
Start-up and use, 7  
Starting the dishwasher  
Measuring out the detergent  
Wash options  
Wash cycles, 8  
Table of wash cycles  
Rinse aid and refined salt, 9  
Measuring out the rinse aid  
Measuring out the refined salt  
Care and maintenance, 10  
Shutting off the water and electricity supplies  
Cleaning the dishwasher  
Preventing unpleasant odours  
Cleaning the sprayer arms  
Cleaning the water inlet filter  
Cleaning the filters  
Leaving the machine unused for extended  
periods  
Precautions and advice, 11  
General safety  
Disposal  
Saving energy and respecting the environment  
Troubleshooting, 12  
Guarantee, 13  
After Sales Service, 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Anti-flooding protection  
Anti-condensation strip*  
EN  
To ensure floods do not occur, the dishwasher:  
- is provided with a special system which blocks the  
water supply in the event of anomalies or leaks from  
inside the appliance.  
After installing the dishwasher, open the door and stick  
the adhesive transparent strip under the wooden shelf in  
order to protect it from any condensation which may  
form.  
Some models are also equipped with the supplementary  
safety device New Acqua Stop*, which guarantees anti-  
flooding protection even in the event of a supply hose  
rupture.  
Advice regarding the first wash cycle  
After the appliance has been installed, immediately  
before running the first wash cycle, completely fill the  
salt dispenser with water and add only then  
approximately 1 kg of salt (see chapter entitled Rinse aid  
and refined salt). The water may overflow: this is normal  
and is not a cause for concern. Select the water  
hardness value (see chapter entitled Rinse aid and  
refined salt). - After the salt has been poured into the  
machine, the LOW SALT indicator light* switches off.  
WARNING: HAZARDOUS VOLTAGE!  
Under no circumstance should the water inlet hose be  
cut as it contains live electrical parts.  
Electrical connection  
Before inserting the plug into the electrical socket, make  
sure that:  
If the salt container is not filled, the water softener  
and the heating element may be damaged as a result.  
• The socket is earthed and complies with current  
regulations.  
• The socket can withstand the maximum load of the  
appliance, which is indicated on the data plate  
located on the inside of the door (see chapter entitled  
Description of the appliance).  
Technical data  
width 44.5 cm  
height 82 cm  
depth 57 cm  
• The power supply voltage falls within the values  
indicated on the data plate on the inside of the door.  
• The socket is compatible with the plug of the  
appliance. If this is not the case, ask an authorised  
technician to replace the plug (see Assistance); do  
not use extension cables or multiple sockets.  
Dimensions  
Capacity  
10 standard place-settings  
Water supply  
pressure  
Power supply  
voltage  
Total absorbed  
power  
0,05 ÷ 1MPa (0.5 ÷ 10 bar)  
7,25 – 145 psi  
See appliance data plate  
Once the appliance has been installed, the power  
supply cable and the electrical socket should be easily  
accessible.  
See appliance data plate  
See appliance data plate  
Fuse  
The cable should not be bent or compressed.  
This dishwasher conforms to the  
following European Community  
Directives:  
-2006/95/EC (Low Voltage  
-2004/108/EC (Electromagnetic  
Compatibility)  
-2005/32/EC (Comm. Reg.  
1275/2008) (Ecodesign)  
--97/17/EC (Labelling)  
If the power supply cable is damaged, it must be re-  
placed by the manufacturer or its Technical Assistance  
Service in order to prevent all potential hazards. (See Af-  
ter Sales Service)  
The Company shall not be held responsible for any  
incidents that occur if these regulations are not  
observed.  
-2002/96/ EC (Waste Electrical  
and Electronic Equipment WEEE)  
* Only available in selected models.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Electrical Connection  
As the colours of the wires in the mains lead may not  
Electrical Connection  
EN  
correspond with the coloured markings identifying the  
terminal in your plug, proceed as follows:  
connect Green & Yellow wire to terminal market “E” or  
coloured Green or Green & Yellow.  
If your appliance is supplied with a 13 amp. fused plug  
it can be plugged into a 13 amp socket for immediate  
use. Before using the appliance please read the  
instruction below.  
Connect Brown wire to terminal marked “L” or  
coloured Red.  
WARNING: THIS APPLIANCE MUST BE  
EARTHED.  
Connect Blue wire to terminal marked “N” or coloured  
Black.  
THE FOLLOWING OPERATIONS SHOULD BE  
CARRIED OUT BY A QUALIFIED ELECTRICIAN.  
If a 13 amp plug (BS 1363) is used it must be fitted with  
a 13 amp fuse. A15 amp plug must be protected by a 15  
amp fuse, either in the plug or adaptor or at the  
distribution board.  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA  
approved fuse to BS 1362 should always be used, and  
the fuse cover re-fitted. If the fuse cover is lost, the  
plug must not be used until a replacement is obtained.  
If you are in any doubt about the electrical supply to  
your machine, consult a qualified electrician before  
use.  
Replacemente fuse covers:  
If a replacement fuse cover is fitted, it must be of the  
correct colours as indicated by the coloured marking  
or the colour that is embossed in words on the base of  
the plug. Replacements can be obtained directly from  
your nearest Service Depot.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in  
accordance with the following code:  
BLUE  
“NEUTRAL” (“N”)  
“LIVE” (“L”)  
Removing the plug:  
BROWN  
Ifyour appliance has a non-rewireable moulded plug  
and you should wish to remove it to re-route the mains  
cable through partitions, units etc., please esure that  
either:  
GREEN AND YELLOW “EARTH” (“E”) or  
- the plug is replaced by a fused 13 amp re-wireable  
plug  
- or:  
bearing the BSI mark of approval  
- the mains cable is wired directly into a 13 amp cable  
outlet, controlled by a switch, (in compliance with BS  
5733) which is accessible without moving the  
appliance.  
Disposing of the plug:  
Ensure that before disposing of the plug itself, you  
make the pins unusable so that it cannot be  
accidentally inserted into a socket.  
Instruction for connecting cable to an altenative  
plug:  
Important: the wires in the mains lead are coloured  
in accordance with the following code:  
Disposing of the appliance:  
Green & Yellow  
Blue  
- Earth  
- Neutral  
- Live  
When disposing of the appliance please remove the  
plug by cutting the mains cable as close as possible to  
the plug body and dispose of it as described above.  
Brown  
CAUTION:  
- Once the appliance has been installed, the electrical plug  
and socket should remain accessible.  
- The Company shall not be held responsible for any  
incidents that occur if these regulations are not observed.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Description of the  
appliance  
Overall view  
EN  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
Upper rack  
Upper sprayer arm  
Tip-up compartments  
Rack height adjuster  
Lower rack  
Lower sprayer arm  
Cutlery basket  
Washing filter  
Salt dispenser  
10. Detergent and rinse aid dispensers  
11. Data plate  
12. Control Panel***  
Control panel  
Select wash cycle button  
ON/OFF  
indicator light  
Wash cycle indicator lights  
ON/OFF/RESET  
button  
***Only in completely built-in models.  
* Only available in selected models.  
The number and type of wash cycles and options may vary depending on the dishwasher model.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Loading the racks  
Before loading the racks, remove all food residues from  
the crockery and empty liquids from glasses and cups.  
Arrange the crockery so that it is held in place firmly and  
does not tip over.  
Adjusting the height of the upper rack  
In order to make it easier to arrange the crockery, the upper  
rack may be moved to a higher or lower level.  
EN  
The height of the upper rack should ideally be  
adjusted WHEN THE RACK IS EMPTY.  
After loading the appliance, check that the sprayer arms  
can rotate freely.  
Never lift or lower the rack on one side only.  
Lower rack  
Open the left and right guide rail stops  
and pull out the rack; position it higher  
or lower as required, slide it along the  
guide rails until the front wheels are in  
place and close the stops (see figure).  
The lower rack can hold pans, lids, plates, salad bowls, cutlery,  
etc. as seen in the Loading examples.  
Plates and large covers should be placed at the sides of the  
rack, ensuring that they do not block the rotation of the upper  
sprayer arm.  
Some dishwasher models are fitted  
with tip-up sections*, which can be  
used in a vertical position when  
If the rack is fitted with “Dual Space”  
handles*(see figure), pull out the  
upper rack until it reaches its stop  
point, grip the handles at the sides of  
the rack and move it upwards or  
downwards, then slowly let it fall back  
into place.  
arranging plates or in a horizontal  
position when arranging pans and  
salad bowls.  
Cutlery basket  
Loading examples for the upper rack  
The type of cutlery basket may vary according to the  
dishwasher model: The cutlery basket should be positioned at  
the front of the lower rack, by sliding it between the fixed  
inserts, or on the upper rack when the half load option has been  
selected (in models featuring this option).  
- It has a collapsible  
sliding system which  
means the cutlery can be  
arranged in the best  
possible way.  
Loading examples for the upper rack  
Knives and other utensils with sharp edges must be  
placed in the cutlery basket with the points facing downwards,  
or they must be positioned horizontally in the tip-up  
compartments on the upper rack.  
Cutlery basket positioning examples  
Items which should not be washed in the  
dishwasher  
• Wooden items, objects with wooden or horn handles or  
glued-on parts.  
• Items made from aluminium, copper, brass, pewter or tin.  
• Items made from plastic material which is not heat-resistant.  
• Antique or hand-painted porcelain.  
ù
Upper rack  
• Antique silver. Silver which is not antique may, however, be  
washed in the dishwasher using a delicate wash cycle,  
provided that it does not come into contact with other  
metals.  
Load this rack with delicate and lightweight crockery: glasses,  
tea and coffee cups, saucers, small salad bowls, saucepans  
and small saucepans which are not too soiled, using the  
Loading examples as a guide.  
We recommend the use of crockery which is dishwasher  
safe.  
• Mugs and cups, long sharp knives and serving utensils:  
place these on the tip-up compartments**.  
*Only available in selected models.  
** The number and position may vary.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Start-up and use  
Starting the dishwasher  
Measuring out the detergent  
EN  
A good wash result also depends on the correct  
amount of detergent being used; exceeding the  
stated amount does not result in a more effective  
wash and increases environmental pollution.  
1. Turn the water tap on.  
2. Open the door and press the ON/OFF button: you will  
hear a short beep and the ON/OFF and wash cycle  
indicator lights switch on for a few seconds.  
3. Measure out the detergent (see below).  
4. Load the racks (see chapter entitled Loading the  
racks).  
Only use detergent which has been  
specifically designed for dishwashers.  
DO NOT USE washing up liquid.  
5. Select the wash cycle in accordance with the type of  
crockery and its soil level (see Table of wash cycles), by  
pressing the SELECT WASH CYCLE button; the indicator  
light corresponding to the selected wash cycle will  
switch on.  
Using excessive detergent may result in foam  
residue remaining in the machine after the cycle  
has ended.  
The use of tablets is only recommended for  
models which offer the MULTI-FUNCTIONAL  
TABLETS option.  
7. Start the wash cycle by shutting the door: after a few  
seconds have passed, a long beep signals the start of  
the wash cycle.  
To achieve the best results from each washing  
and drying cycle, powder detergent, rinse aid  
liquid and salt should be used.  
8. Two short beeps and one long one indicate the end of  
the wash cycle and the indicator light corresponding to  
the wash cycle flashes slowly. Open the door, switch off  
the appliance by pressing the ON/OFF button, shut off  
the water tap and unplug the appliance from the  
electricity socket.  
Compartment A: Washing detergent  
Compartment B: Pre-wash detergent  
1. Open cover C by pressing  
button D.  
9. Wait for a few minutes before removing the crockery,  
in order to avoid burns. Unload the racks, beginning with  
the lower level.  
2. Pour in the detergent after  
consulting the Table of wash  
cycles:  
- The machine will switch off automatically  
during certain periods of inactivity, in order to  
minimise electricity consumption.  
• For powder detergent use  
compartments A and B.  
• For detergent in tablet form:  
when the cycle requires 1  
Modifying a wash cycle in progress  
tablet, place it in compartment  
A and close the cover; when it requires 2, place the  
second tablet at the bottom of the appliance.  
3. Remove detergent residues from the edges of the  
compartment and close the cover until it clicks.  
If a mistake was made during the wash cycle selection  
process it is possible to change the cycle, provided that it  
has only just begun: open the door, taking care to avoid the  
escaping steam, and press and hold the ON/OFF button;  
the machine will switch off with a long beep. Switch the  
machine back on using the ON/OFF button and select the  
new wash cycle using the SELECT WASH CYCLE button;  
start the cycle by closing the door.  
Adding extra crockery  
Without switching off the machine, open the door, taking  
care to avoid the escaping steam, and place the  
crockery inside the dishwasher. Close the door: the  
cycle starts from the point at which it was interrupted.  
Accidental interruptions  
If the door is opened during the wash cycle, or if there is  
a power cut, the cycle stops. It starts again from the point  
at which it was interrupted once the door has been shut  
or the electricity supply is restored.  
* Only available in selected models.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wash cycles  
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the  
dishwasher, reduce the amount of detergent used accordingly.  
EN  
The number and type of wash cycles and options may vary depending on the dishwasher model.  
Wash cycle  
duration  
(tolerance  
10%)  
Detergent  
(A) = compartment A  
(B) = compartment B  
Wash cycle selection  
instructions  
Wash  
cycle  
Drying  
Hrs. Min.  
Powder  
Liquid  
Tablets  
Extremely soiled dishes and  
pans (not to be used for  
delicate items).  
25 g (A)  
25 ml (A)  
1 (A)  
1 (A)  
Yes  
2:25’  
1:50’  
Intensive  
Normal  
Normally soiled pans and  
dishes. Standard daily wash  
cycle.  
21 g (A)  
4 g (B)  
21 ml (A)  
4 ml (B)  
Yes  
Preliminary wash cycle for  
dishes while the load is  
awaiting completion with the  
dishes from the next meal.  
No  
No  
No  
No  
0:08’  
2:50’  
Soak  
Environmentally-friendly wash  
cycle with low energy  
consumption levels, suitable for  
pans and dishes.  
25 g (A)  
25 ml (A)  
1 (A)  
Yes  
Eco*  
Notes:  
* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it  
uses less energy and is les harmful to the environment.  
Note for Test Laboratories: for detailed information relating to comparative EN testing conditions, please send an email  
to the following address: [email protected]  
To make it easier to measure out the detergent, it is worth remembering that:  
1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. of powder = approximately 5 ml of  
liquid  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rinse aid and refined salt  
number 2).  
E.g. Hardness level 1 (1 cycle indicator light flashing)  
st nd  
Hardness level 2 (1 cycle indicator light ON, 2 cycle  
Only use products which have been  
specifically designed for dishwashers.  
Do not use table salt or industrial salt, or  
washing up liquid.  
st  
EN  
indicator light flashing)  
nd  
Hardness level 3 (1st and 2 cycle indicator lights ON, 3  
rd  
Follow the instructions given on the packaging.  
cycle indicator light flashing etc) up to maximum 5 levels.  
If using a multi-functional product it is not necessary to  
add rinse aid; however, we recommend that you add salt,  
especially if you live in an area where the water is hard or  
very hard. Follow the instructions given on the packaging.  
- Press the P button repeatedly until the desired hardness  
level has been reached (1-2-3-4-5*see Water hardness  
table).  
- To exit the function, wait approximately few seconds or press  
another option*button, or switch off the machine using the ON/  
OFF button.  
If you do not add salt or rinse aid, the LOW  
SALT* and LOW RINSE AID* indicator lights  
remain lit.  
Even if using multi-functional tablets, the salt dispenser should  
still be filled.  
Measuring out the rinse aid  
Rinse aid makes it easier for the crockery to dry, as water  
runs off surfaces more readily and therefore does not leave  
streaks or marks.  
Water Hardness Table  
°dH  
0
°fH  
mmol/l  
level  
11  
0
20 1.1  
2
3
6
9
1
2
3
12 17 21  
17 34 31  
34 50 61  
30 2.1  
60 3.1  
90 6.1  
The rinse aid dispenser should be filled:  
• When the LOW RINSE AID*indicator light on the control  
panel is illuminated;  
4*  
For values between 0°f and 10°f, we do not  
recommend the use of salt.  
* this setting may cause a slight increase in the  
duration of the cycle.  
1. Open the dispenser by turning  
the lid (G) in an anticlockwise  
direction.  
2. Pour in the rinse aid, making  
(°dH = hardness measured in German degrees - °f =  
hardness measured in French degrees - mmol/l = millimoles  
per litre)  
sure it does not overflow from the  
F
dispenser. If this happens, clean  
the spill immediately with a dry  
G
Measuring out the refined salt  
In order to achieve the best possible results using a wash  
cycle, make sure that the dispenser is never empty. Refined  
salt removes limescale from the water, thus avoiding the  
formation of deposits on crockery.  
cloth.  
3. Screw the lid back on.  
NEVER pour the rinse aid directly into the appliance tub.  
Adjusting the amount of rinse aid  
The salt dispenser is located in the lower part of the  
dishwasher (see Description) and should be filled:  
• When the green float*cannot be seen by simply looking at  
the cap of the salt dispenser.  
If you are not completely satisfied with the drying results, you  
may adjust the quantity of rinse aid used. Use a screwdriver  
to turn the dosage adjuster (F) to one of the 6 pre-set  
positions (the default position is set to 4):  
• When the LOW SALT*indicator light on the control panel is  
illuminated;  
• If there are streaks on the crockery, set the adjustment  
device to a lower number (1-3).  
• If drops of water remain on the crockery or if there are  
limescale marks present after the cycle has finished, set the  
adjuster to a higher number (4-6).  
1. Remove the lower rack and unscrew the  
container cap (anticlockwise).  
2. The first time you do this: fill the water  
tank right up to its edge.  
3. Position the funnel*(see figure) and fill  
Setting the water hardness  
the salt container right up to its edge (this should hold  
approximately 1 kg); it is not unusual for a little water to leak  
out.  
Every dishwasher is equipped with a water softener which, by  
using refined salt designed especially for this type of  
appliance, supplies water without limescale which is then used  
to wash the crockery.  
4. Remove the funnel*and wipe any salt residue away from  
the opening; rinse the cap under running water and then  
screw it on, the head facing downwards so as to let the water  
flow out of the four cracks which are arranged in a star shape  
on the lower part of the cap. (Salt cap with green float*)  
It is advisable to perform this procedure every time you  
add salt to the container.  
This dishwasher offers a setting which helps to reduce  
pollution and optimises washing performance in accordance  
with the water hardness level in your area. This information can  
be obtained from the organisation which supplies your  
household with water.  
- Open the door and switch on the machine by pressing the  
ON/OFF button.  
Make sure the cap is screwed on tightly, so that no detergent  
can get into the container during the wash cycle (this could  
damage the water softener beyond repair).  
- Press the P button and hold for approximately 5 seconds;  
two short beeps will sound and the indicator light  
corresponding to the set degree of hardness will flash slowly  
on the control panel (the water softening system is set to  
When necessary, measure out the salt before a wash  
cycle so that any saline solution which has leaked out of the  
salt dispenser is removed.  
9
* Only available in selected models.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and maintenance  
Clean the water inlet filter at the tap outlet regularly.  
- Turn off the water tap.  
Shutting off the water and electricity  
supplies  
• Turn off the water tap after every wash cycle to avoid  
EN  
- Unscrew the end of the water inlet hose, remove the filter and  
clean it carefully under running water.  
- Replace the filter and screw the water hose back into  
leaks.  
• Always unplug the appliance when cleaning it and  
when performing maintenance work.  
position.  
Cleaning the filters  
Cleaning the dishwasher  
The filter assembly consists of three filters which remove food  
residues from the washing water and then recirculate the  
water. They should be cleaned if you wish to achieve the best  
results in every wash.  
• The external surfaces of the machine and the control  
panel may be cleaned using a non-abrasive cloth  
which has been dampened with water. Do not use  
solvents or abrasive products.  
Clean the filters regularly.  
• Any marks on the inside of the appliance may be  
removed using a cloth dampened with water and a  
little vinegar.  
The dishwasher should not be used without filters, or if the  
filter is loose.  
• After several washes, check the filter assembly and if  
necessary clean it thoroughly under running water, using a  
non-metallic brush and following the instructions below:  
1. Turn the cylindrical filter C in an anti-clockwise direction  
and pull it out (fig. 1).  
Preventing unpleasant odours  
• Always keep the door of the appliance ajar in order to  
avoid moisture from forming and being trapped inside  
the machine.  
2. Remove the cup filter B by exerting a slight pressure on the  
side flaps (fig. 2).  
• Clean the seals around the door and detergent  
dispensers regularly using a damp sponge. This will  
avoid food becoming trapped in the seals, which is  
the main cause behind the formation of unpleasant  
odours.  
3. Slide out the stainless steel plate filter A (fig. 3).  
4. Inspect the trap and remove any food residue. NEVER  
REMOVE the wash cycle pump (black detail) (fig. 4).  
Cleaning the sprayer arms  
Food residue may become encrusted onto the sprayer  
arms and block the holes used to spray the water. It is  
therefore recommended that the arms are checked from  
time to time and cleaned with a small non-metallic  
brush.  
C
1
2
The two sprayer arms may both be removed.  
To remove the upper sprayer  
arm, rotate the locking ring in  
an anti-clockwise direction.  
The upper sprayer arm  
should be replaced with the  
holes facing upwards.  
A
3
4
The lower sprayer arm can  
be removed by pulling it  
upwards.  
After cleaning the filters, replace the filter assembly and fix it in  
position correctly; this is essential for maintaining the efficient  
operation of the dishwasher.  
Leaving the machine unused for extended  
periods  
• Disconnect the appliance from the electricity supply and  
shut off the water tap.  
Cleaning the water inlet filter*  
If the water hoses are new or have not been used for an  
extended period of time, let the water run to make sure it  
is clear and free of impurities before performing the  
necessary connections. If this precaution is not taken,  
the water inlet could become blocked and damage the  
dishwasher.  
• Leave the door of the appliance ajar.  
• When you return, run a wash cycle when the dishwasher is  
empty.  
*Only available in selected models.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Precautions and advice  
This appliance was designed and manufactured in  
Saving energy and respecting the  
environment  
EN  
compliance with current international safety standards. The  
following information has been provided for safety reasons  
and should therefore be read carefully.  
Saving water and energy  
• Only begin a wash cycle when the dishwasher is full. While  
waiting for the dishwasher to be filled, prevent unpleasant  
odours using the Soak cycle (see Wash cycles).  
• Select a wash cycle which is suited to the type of crockery  
and to the soil level of the crockery using the Table of wash  
cycles:  
General safety  
• This appliance is not intended for use by persons  
(including children) with reduced physical, sensory or  
mental capabilities, or lack of experience and knowledge,  
unless they have been given supervision or instruction  
concerning use of the appliance by a person responsible  
for their safety.  
- For dishes with a normal soil level, use the Eco wash  
cycle, which guarantees low energy and water  
consumption levels.  
- If the load is smaller than usual activate the Half load  
option*(see Start-up and use).  
• Children should be supervised to ensure that they do not  
play with the appliance.  
• If your electricity supply contract gives details of electricity  
saving time bands, run wash cycles during the periods  
when a lower tariff is applied. The Delayed start*button  
(see Start-up and use) helps you organise the wash cycles  
accordingly.  
• The appliance was designed for domestic use inside the  
home and is not intended for commercial or industrial use.  
• The appliance must be used by adults only, to wash  
domestic crockery in accordance with the instructions in  
this manual.  
• The appliance must not be installed outdoors, even in  
covered areas. It is extremely dangerous to leave the  
machine exposed to rain and storms.  
Phosphate-free and chlorine-free detergents  
containing enzymes  
• Do not touch the appliance when barefoot.  
• When unplugging the appliance always pull the plug from  
the mains socket, do not pull on the cable.  
• We strongly recommend that you use detergents that do  
not contain phosphates or chlorine, as these products are  
harmful to the environment.  
• The water supply tap must be shut off and the plug should  
be removed from the electrical socket before cleaning the  
appliance or carrying out any maintenance work.  
• If the appliance breaks down, do not under any  
circumstances touch the internal parts in an attempt to  
perform the repair work yourself.  
• Enzymes provide a particularly effective action at  
temperatures around 50°C, and as a result detergents  
containing enzymes can be used in conjunction with low-  
temperature wash cycles in order to achieve the same  
results as a normal 65°C wash cycle.  
• Never touch the heating element.  
• To avoid wasting detergent, use the product in appropriate  
quantities based on the manufacturer’s recommendations,  
the hardness of the water and the soil level and quantity of  
crockery to be washed. Even if they are biodegradable,  
detergents contain substances which may alter the balance  
of nature.  
• Do not lean or sit on the open door of the appliance: this  
may cause the appliance to overturn.  
• The door should not be left open as it may create a  
dangerous obstacle.  
• Keep detergent and rinse aid out of reach of children.  
• The packaging material should not be used as a toy.  
Disposal  
• Disposal of packaging materials: observe local legislation  
so that the packaging may be reused.  
• The European Directive 2002/96/EC relating to Waste  
Electrical and Electronic Equipment (WEEE) states that  
household appliances should not be disposed of using the  
normal solid urban waste cycle. Exhausted appliances  
should be collected separately in order to optimise the cost  
of re-using and recycling the materials inside the machine,  
while preventing potential damage to the atmosphere and  
to public health. The crossed-out dustbin is marked on all  
products to remind the owner of their obligations regarding  
separated waste collection.  
For further information relating to the correct disposal of  
household appliances, owners may contact the relevant  
public authority or the local appliance dealer.  
* Only available in selected models.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Whenever the appliance fails to work, check for a solution from the following list before calling for  
Assistance.  
EN  
Problem:  
Possible causes / Solutions:  
The dishwasher does not start or  
cannot be controlled  
Switch off the appliance by pressing the ON/OFF button, switch it back on after  
approximately one minute and reset the program.  
The appliance has not been plugged in properly.  
The dishwasher door has not been shut properly.  
The door wont close  
The lock was released. Strongly push the door until a clackingnoise is heard.  
No water drains out from the  
dishwasher.  
The dishwasher cycle has not yet finished.  
The water inlet hose is bent (see Installation).  
The drain duct is blocked.  
The filter is clogged up with food residues.  
The dishwasher makes excessive  
noise.  
The dishes are rattling against each other or against the sprayer arms.  
An excessive amount of foam has been produced: the detergent has not been  
measured out correctly or it is not suitable for use in dishwashers (see Start-up  
and use).  
The dishes and glasses are  
covered in a white film or  
limescale deposits.  
The level of the refined salt is low or the dosage setting is not suited to the  
hardness of the water (see Rinse aid and salt).  
The lid on the salt dispenser is not closed properly.  
The rinse aid has been used up or the dosage is too low.  
The dishes and glasses are  
The rinse aid dosage is too high.  
streaked or have a bluish tinge.  
The crockery has not been dried  
properly.  
A wash cycle without a drying program has been selected.  
The rinse aid has been used up or the dosage is too low (see Rinse aid and  
salt).  
The rinse aid dispenser setting is not suitable.  
The crockery is made from non-stick material or plastic.  
The dishes are not clean.  
The racks are overloaded (see Loading the racks).  
The crockery has not been arranged well.  
The sprayer arms cannot move freely.  
The wash cycle is too gentle (see Wash cycles).  
An excessive amount of foam has been produced: the detergent has not been  
measured out correctly or it is not suitable for use in dishwashers (see Start-up  
and use).  
The lid on the rinse aid compartment has not been shut correctly.  
The filter is dirty or blocked (see Care and maintenance).  
The refined salt level is low (see Rinse aid and salt).  
The dishwasher does not take any There is no water in the mains supply.  
water in - Tap shut-off alarm  
The water inlet hose is bent (see Installation).  
Turn on the tap and the appliance will start after a few minutes.  
The appliance lock has been activated because no action was taken when the  
(several short beeps* are emitted)  
(the 2 (Normal) and 3 (Soak) WASH  
CYCLES indicator lights flash).  
beeps* sounded.  
Switch off the appliance using the ON/OFF button, turn on the tap and switch  
the appliance back on after 20 seconds by pressing the same button. Re-  
program the appliance and restart the wash cycle.  
Water inlet hose alarm / Water inlet Switch off the appliance by pressing the ON/OFF button. Shut off the water tap  
filter blocked  
to eliminate the risk of flooding and remove the plug from the electrical socket.  
Make sure the water inlet filter has not become blocked by impurities (see Care  
and maintenancechapter).  
(the 1 (Intensive), the 2 (Normal) and  
the 3 (Soak) WASH CYCLES  
indicator lights flash).  
* Only available in selected models.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Guarantee  
Guarantee  
EN  
12 months Parts and Labour Guarantee  
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for  
twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of  
either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our operating and  
maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any  
person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper  
installation.  
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,  
batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-  
DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Indesit also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering  
your appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for  
our engineer’s time. To activate the extra parts warranty on your appliance, simply call our registration line on  
08448 24 24 24 (Republic of Ireland 01 230 0800)  
Extended Guarantees  
We offer a selection of protection plans that enable you to fully cover yourself against the expense of repair bills  
for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226 (Republic of  
Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you experience  
any technical difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08448  
224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an  
engineer to call.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
After Sales Service  
After Sales Service  
EN  
No one is better placed to care for your Indesit appliance during the course of its working life than us – the  
manufacturer.  
Essential Contact Information  
Indesit Service  
We are the largest service team in the UK and Ireland offering you access to 400 skilled telephone advisors and  
1000 fully qualified engineers on call to ensure you receive fast, reliable, local service.  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and  
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Indesit ownership. To activate your free 5 year parts guarantee you  
must register your appliance with us.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17  
Recycling and Disposal Information  
As part of Indesit’s continued commitment to helping the environment, Indesit reserves the right to use quality,  
recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the  
door, plug, and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure  
that the appliance can no longer be plugged into mains socket, and the door cannot be locked shut.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
195075388.02  
05/2011 - Xerox Fabriano  
EN  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Intel Computer Hardware BLKDH57JG User Manual
Interact TV Home Theater System MX Z User Manual
JVC Car Stereo System KW XC838 User Manual
JVC DVD VCR Combo LPT0838 001C User Manual
JVC Home Security System TK AM200U User Manual
Kenmore Microwave Oven 87000 User Manual
Kenmore Sewing Machine 385160201 User Manual
Kenwood Car Stereo System DNX7180 User Manual
King Canada Drill KC 110C User Manual
King Canada Planer 8333 User Manual