Operating instructions
DISHWASHER
Contents
EN
Installation, 2-3-4
Positioning and levelling
English, 1
Connecting the water and electricity supplies
Advice regarding the first wash cycle
Technical data
Electrical connection
Description of the appliance, 5
Overall view
Control panel
Loading the racks, 6
Lower rack
DIF 04
DIF 16
Cutlery basket
Upper rack
Start-up and use, 7
Starting the dishwasher
Measuring out the detergent
Wash options
Wash cycles, 8
Table of wash cycles
Rinse aid and refined salt, 9
Measuring out the rinse aid
Measuring out the refined salt
Care and maintenance, 10
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the filters
Leaving the machine unused for extended
periods
Precautions and advice, 11
General safety
Disposal
Saving energy and respecting the environment
Troubleshooting, 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the water outlet hose
Anti-condensation strip*
EN
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order to
protect it from any condensation which may form.
Connect the outlet hose (without bending it) to a drain duct
with a minimum diameter of 4 cm. Alternatively, rest it over a
sink or tub; the free end of the hose should not remain
immersed in water.
Advice regarding the first wash cycle
After the appliance has been installed, immediately before
running the first wash cycle, completely fill the salt dispenser
with water and add only then approximately 1 kg of salt (see
chapter entitled Rinse aid and refined salt). The water may
overflow: this is normal and is not a cause for concern. Select
the water hardness value (see chapter entitled Rinse aid and
refined salt). - After the salt has been poured into the
machine, the LOW SALT indicator light* switches off.
The special plastic elbow*
makes it easier to find the
A
best layout: fix the elbow to
the wall securely in order to
prevent the outlet hose from
moving and spilling the dirty
water.
The part of the hose marked
with the letter A should be
between 40 and 100 cm
above the ground (see
If the salt container is not filled, the water softener and the
heating element may be damaged as a result.
figure).
We advise against the use of hose extensions.
Electrical connection
Before inserting the plug into the electrical socket, make sure
that:
Technical data
• The socket is earthed and complies with current
regulations.
width 59.5 cm
Dimensions
Capacity
height 82 cm
depth 57 cm
• The socket can withstand the maximum load of the
appliance, which is indicated on the data plate located on
the inside of the door (see chapter entitled Description of
the appliance).
12 standard place-settings
• The power supply voltage falls within the values indicated
on the data plate on the inside of the door.
• The socket is compatible with the plug of the appliance. If
this is not the case, ask an authorised technician to replace
the plug (see Assistance); do not use extension cables or
multiple sockets.
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
4.3 psi – 145 psi
Power supply
voltage
See appliance data plate
See appliance data plate
See appliance data plate
Total absorbed
power
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
Fuse
This dishwasher conforms to
the following European
Community Directives:
-73/23/EEC dated 19/02/73
(Low Voltage) and
subsequent modifications
-89/336/EEC dated 03/05/89
(Electromagnetic
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in order
to prevent all potential hazards. (See Assistance)
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
Compatibility)
and subsequent modifications
-97/17/EC (Labelling)
-2002/96/ CE (Waste
Electrical and Electronic
Equipment WEEE)
* Only available in selected models.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ElectricalConnection
As the colours of the wires in the mains lead may not
Electrical Connection
EN
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market “E” or
coloured Green or Green & Yellow.
Connect Brown wire to terminal marked “L” or coloured
Red.
If your appliance is supplied with a 13 amp. fused plug
it can be plugged into a 13 amp socket for immediate
use. Before using the appliance please read the
instruction below.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
Connect Blue wire to terminal marked “N” or coloured
Black.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
If a 13 amp plug (BS 1363) is used it must be fitted with
a 13 amp fuse. A15 amp plug must be protected by a 15
amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt about the electrical supply to
your machine, consult a qualified electrician before
use.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used, and
the fuse cover re-fitted. If the fuse cover is lost, the
plug must not be used until a replacement is obtained.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colours as indicated by the coloured marking
or the colour that is embossed in words on the base of
the plug. Replacements can be obtained directly from
your nearest Service Depot.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE
BROWN
“NEUTRAL” (“N”)
“LIVE” (“L”)
Removing the plug:
Ifyour appliance has a non-rewireable moulded plug
and you should wish to remove it to re-route the mains
cable through partitions, units etc., please esure that
either:
GREEN AND YELLOW “EARTH” (“E”)
- the plug is replaced by a fused 13 amp re-wireable
plug
- or:
bearing the BSI mark of approval
GREEN &
YELLOW
- the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with BS
5733) which is accessible without moving the
appliance.
13 amp fuse
BROWN
CROSS-BAR
CORD GRIP
BLUE
Disposing of the plug:
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket.
Instruction for connecting cable to an altenative
plug:
Important: the wires in the mains lead are coloured
in accordance with the following code:
Disposing of the appliance:
Green & Yellow
Blue
- Earth
- Neutral
- Live
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible to
the plug body and dispose of it as described above
Brown
CAUTION:
- Once the appliance has been installed, the electrical plug
and socket should remain accessible.
- The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the
appliance
Overall view
1.
2.
3.
4.
5.
6.
7.
8.
9.
Upper rack
EN
Upper sprayer arm
Tip-up compartments
Rack height adjuster
Lower rack
Lower sprayer arm
Cutlery basket
Washing filter
Salt dispenser
3
2
1
4
10. Detergent and rinse aid dispensers
11. Data plate
12. Control Panel***
5
6
9
8
7
10
11
10
11
12
Control panel
Select wash
cycle button
Low Salt
indicator light*
ON/OFF
indicator light
Wash cycle indicator lights
ON/OFF/RESET
button
Low Rinse Aid
indicator light*
***Only in completely built-in models.
* Only available in selected models.
The number and type of wash cycles and options may vary depending on the dishwasher model.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the racks
Adjusting the height of the upper rack
In order to make it easier to arrange the crockery, the upper
rack may be moved to a higher or lower level.
Before loading the racks, remove all food residues from
the crockery and empty liquids from glasses and cups.
After loading the appliance, check that the sprayer arms
can rotate freely.
EN
The height of the upper rack should ideally be adjusted WHEN
THE RACK IS EMPTY.
Lower rack
The lower rack can hold pans, lids, plates, salad bowls,
cutlery, etc. as seen in the Loading examples.
Plates and large covers should be placed at the sides of the
rack, ensuring that they do not block the rotation of the upper
sprayer arm.
Some dishwasher models are fitted with tip-up sections,
which can be used in a vertical position when arranging
plates or in a horizontal position when arranging pans and
salad bowls.
Never lift or lower the rack on one side only.
Open the left and right guide rail stops
and pull out the rack; position it higher or
lower as required, slide it along the guide
rails until the front wheels are in place
and close the stops (see figure).
If the rack is fitted with Dual Space
handles* (see figure), pull out the upper
rack until it reaches its stop point, grip the
handles at the sides of the rack and move
it upwards or downwards, then slowly let it
fall back into place.
Loading examples for the upper rack
Cutlery basket
The type of cutlery basket may vary according to the
dishwasher model: it may be modular, non-modular or a sliding
version. The non-modular basket must only be positioned at the
front of the lower rack.
The modular basket may be separated into two parts, a solution
which is recommended when performing a half load wash (only
in models offering this option), is available in a sliding version
(positioned at any point on the lower rack by sliding it between
the fixed or tip-up inserts.
Loading examples for the lower rack
- Both versions are fitted with a collapsible sliding system which
means the cutlery can be arranged in the best possible way.
Knives and other utensils with sharp edges must be
placed in the cutlery basket with the points facing
downwards, or they must be positioned horizontally in the tip-
up compartments on the upper rack.
Items which should not be washed in the
dishwasher
• Wooden items, objects with wooden or horn handles or
glued-on parts.
• Items made from aluminium, copper, brass, pewter or tin.
• Items made from plastic material which is not heat-resistant.
• Antique or hand-painted porcelain.
Cutlery basket positioning examples
• Antique silver. Silver which is not antique may, however, be
washed in the dishwasher using a delicate wash cycle,
provided that it does not come into contact with other metals.
We recommend the use of crockery which is dishwasher
safe.
Upper rack
Load this rack with delicate and lightweight crockery:
glasses, tea and coffee cups, saucers, small salad bowls,
saucepans and small saucepans which are not too soiled,
using the Loading examples as a guide.
• Mugs and cups: place these on the tip-up compartments**.
• Long sharp knives and serving utensils: place these on the
tip-up compartments**.
* Only available in selected models.
** The number and position may vary.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Start-up and use
Starting the dishwasher
Measuring out the detergent
EN
A good wash result also depends on the correct amount
of detergent being used; exceeding the stated amount
does not result in a more effective wash and increases
environmental pollution.
1. Turn the water tap on.
2. Open the door and press the ON/OFF button: you will
hear a short beep and the ON/OFF and wash cycle
indicator lights switch on for a few seconds.
3. Measure out the detergent (see below).
4. Load the racks (see chapter entitled Loading the
racks).
Only use detergent which has been
specifically designed for dishwashers.
DO NOT USE washing up liquid.
5. Select the wash cycle in accordance with the type of
crockery and its soil level (see Table of wash cycles), by
pressing the SELECT WASH CYCLE button; the indicator
light corresponding to the selected wash cycle will
switch on.
7. Start the wash cycle by shutting the door: after a few
seconds have passed, a long beep signals the start of
the wash cycle.
8. Two short beeps and one long one indicate the end of
the wash cycle and the indicator light corresponding to
the wash cycle flashes slowly. Open the door, switch off
the appliance by pressing the ON/OFF button, shut off
the water tap and unplug the appliance from the
electricity socket.
9. Wait for a few minutes before removing the crockery,
in order to avoid burns. Unload the racks, beginning with
the lower level.
Using excessive detergent may result in foam
residue remaining in the machine after the cycle
has ended.
The use of tablets is only recommended for
models which offer the MULTI-FUNCTIONAL
TABLETS option.
To achieve the best results from each washing
and drying cycle, powder detergent, rinse aid
liquid and salt should be used.
Compartment A: Washing detergent
Compartment B: Pre-wash detergent
1. Open cover C by pressing
button D.
D
A
B
2. Pour in the detergent after
consulting the Table of wash
cycles:
The order in which the different wash programmes are
displayed will change according to the frequency with
which each cycle is used.
• For powder detergent use
compartments A and B.
• For detergent in tablet form:
when the cycle requires 1 tablet,
C
Modifying a wash cycle in progress
place it in compartment A and close the cover; when it
requires 2, place the second tablet at the bottom of the
appliance.
3. Remove detergent residues from the edges of the
compartment and close the cover until it clicks.
If a mistake was made during the wash cycle selection
process it is possible to change the cycle, provided that it
has only just begun: open the door, taking care to avoid the
escaping steam, and press and hold the ON/OFF button;
the machine will switch off with a long beep. Switch the
machine back on using the ON/OFF button and select the
new wash cycle using the SELECT WASH CYCLE button;
start the cycle by closing the door.
Adding extra crockery
Without switching off the machine, open the door, taking
care to avoid the escaping steam, and place the
crockery inside the dishwasher. Close the door: the
cycle starts from the point at which it was interrupted.
Accidental interruptions
If the door is opened during the wash cycle, or if there is
a power cut, the cycle stops. It starts again from the point
at which it was interrupted once the door has been shut
or the electricity supply is restored.
* Only available in selected models.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash cycles
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the
dishwasher, reduce the amount of detergent used accordingly.
EN
The number and type of wash cycles and options may vary depending on the dishwasher model.
Wash cycle
duration
(tolerance
10%)
Detergent
(A) = compartment A
(B) = compartment B
Wash cycle selection
instructions
Wash
cycle
Drying
Hrs. Min.
Powder
Liquid
Tablets
1 (A)
1 (bottom
of the
Extremely soiled dishes and
pans (not to be used for
delicate items).
30 g (A)
5 g (B)
30 ml (A)
5 ml (B)
Yes
Yes
1:54’
1:46’
appliance)
Intensive
Normal
Normally soiled pans and
dishes. Standard daily wash
cycle.
25 g (A)
5 g (B)
25 ml (A)
5 ml (B)
1 (A)
Preliminary wash cycle for
dishes while the load is
awaiting completion with the
dishes from the next meal.
No
No
No
No
0:08’
2:35’
Soak
Environmentally-friendly wash
cycle with low energy
consumption levels, suitable for
pans and dishes.
25 g (A)
5 g (B)
25 ml (A)
5 ml (B)
1 (A)
Yes
Eco*
Economic and fast wash to be
used for lightly soiled dishes.
(Run cycle immediately after
use) (2 plates + 2 glasses + 4
pieces of cutlery + 1 saucepan
+ 1 small frying pan).
Economic and fast wash for
delicate items which are
sensitive to high temperatures.
(Run cycle immediately after
use) (12 glasses + delicate
plates).
25 g (A)
30 g (A)
25 ml (A)
30 ml (A)
1 (A)
1 (A)
No
0:35’
1:33’
Quick
Yes
Crystal
Notes:
Optimum performance levels when using the "Quick wash" cycle can be achieved by observing the maximum amounts of crockery
specified.
* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less
energy and is les harmful to the environment.
Note for Test Laboratories: for detailed information relating to comparative EN testing conditions, please send an email to the
following address: [email protected]
To make it easier to measure out the detergent, it is worth remembering that:
1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. of powder = approximately 5 ml of liquid
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Rinse aid and refined salt
slowly on the control panel (the water softening system is
set to number 3).
Only use products which have been
specifically designed for dishwashers.
Do not use table salt or industrial salt, or
washing up liquid.
EN
- Press the P button repeatedly until the desired hardness
level has been reached (1-2-3-4-5* see Water hardness
table).
- To exit the function, wait approximately 30 seconds or switch off
the machine using the ON/OFF button.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to
add rinse aid; however, we recommend that you add salt,
especially if you live in an area where the water is hard
or very hard. Follow the instructions given on the
packaging.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
Water Hardness Table
°dH
0
°fH
mmol/l
level
If you do not add salt or rinse aid, the LOW SALT*
and LOW RINSE AID* indicator lights remain lit.
6
0
10
0
1
1
2
3
4
6
11 11
20 1.1
30 2.1
60 3.1
90 6.1
2
3
6
9
12 17 21
17 34 31
34 50 61
Measuring out the rinse aid
5*
Rinse aid makes it easier for the crockery to dry, as water
runs off surfaces more readily and therefore does not leave
streaks or marks.
The rinse aid dispenser should be filled:
• When the LOW RINSE AID* indicator light on the control
panel is illuminated;
For values between 0°f and 10°f, we do not
recommend the use of salt.
* this setting may cause a slight increase in the
duration of the cycle.
1. Open the dispenser by turning
the lid (G) in an anticlockwise
direction.
(°dH = hardness measured in German degrees - °f =
hardness measured in French degrees - mmol/l = millimoles
per litre)
2. Pour in the rinse aid, making
sure it does not overflow from the
dispenser. If this happens, clean
the spill immediately with a dry
Measuring out the refined salt
F
G
cloth.
In order to achieve the best possible results using a wash
cycle, make sure that the dispenser is never empty. Refined
salt removes limescale from the water, thus avoiding the
formation of deposits on crockery.
3. Screw the lid back on.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the amount of rinse aid
The salt dispenser is located in the lower part of the
dishwasher (see Description) and should be filled:
• When the green float* cannot be seen by simply looking at
the cap of the salt dispenser.
• When the LOW SALT* indicator light on the control panel is
illuminated;
If you are not completely satisfied with the drying results,
you may adjust the quantity of rinse aid used. Use a
screwdriver to turn the dosage adjuster (F) to one of the 6
pre-set positions (the default position is set to 4):
• If there are streaks on the crockery, set the adjustment
device to a lower number (1-3).
• If drops of water remain on the crockery or if there are
limescale marks present after the cycle has finished, set
the adjuster to a higher number (4-6).
1. Remove the lower rack and
unscrew the cap of the dispenser (in
an anti-clockwise direction).
2. For the first wash cycle only: fill
the dispenser up to the edges with
water.
3. Position the funnel* correctly (see
figure) and fill the salt dispenser up
Setting the water hardness
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of
appliance, supplies water without limescale which is then used
to wash the crockery.
to the edges (approximately 1 kg); it
is normal for a little water to leak out.
4. Remove the funnel, wipe away any salt residue from the
opening and screw the cap on tightly, so that detergent
does not leak into the dispenser during the wash cycle (this
could damage the water softening system beyond repair).
This dishwasher offers a setting which helps to reduce
pollution and optimises washing performance in accordance
with the water hardness level in your area. This information can
be obtained from the organisation which supplies your
household with water.
- Open the door and switch on the machine by pressing the
ON/OFF button.
- Press the P button and hold for approximately 5 seconds;
two short beeps will sound and the indicator light
corresponding to the set degree of hardness will flash
When necessary, measure out the salt before a wash
cycle so that any saline solution which has leaked out of the
salt dispenser is removed.
* Only available in selected models.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
Shutting off the water and electricity
supplies
Cleaning the filters
EN
The filter assembly consists of three filters which remove food
residues from the washing water and then recirculate the
water. They should be cleaned if you wish to achieve the best
results in every wash.
• Turn off the water tap after every wash cycle to avoid
leaks.
• Always unplug the appliance when cleaning it and
when performing maintenance work.
Clean the filters regularly.
The dishwasher should not be used without filters, or if the
filter is loose.
Cleaning the dishwasher
• The external surfaces of the machine and the control
panel may be cleaned using a non-abrasive cloth
which has been dampened with water. Do not use
solvents or abrasive products.
• After several washes, check the filter assembly and if
necessary clean it thoroughly under running water, using a
non-metallic brush and following the instructions below:
1. Turn the cylindrical filter C in an anti-clockwise direction
and pull it out (fig. 1).
2. Remove the cup filter B by exerting a slight pressure on the
side flaps (fig. 2).
3. Slide out the stainless steel plate filter A (fig. 3).
4. Inspect the trap and remove any food residue. NEVER
REMOVE the wash cycle pump (black detail) (fig. 4).
• Any marks on the inside of the appliance may be
removed using a cloth dampened with water and a
little vinegar.
Preventing unpleasant odours
• Always keep the door of the appliance ajar in order to
avoid moisture from forming and being trapped inside
the machine.
B
C
• Clean the seals around the door and detergent
dispensers regularly using a damp sponge. This will
avoid food becoming trapped in the seals, which is
the main cause behind the formation of unpleasant
odours.
C
1
2
Cleaning the sprayer arms
A
Food residue may become encrusted onto the sprayer
arms and block the holes used to spray the water. It is
therefore recommended that the arms are checked from
time to time and cleaned with a small non-metallic
brush.
4
3
The two sprayer arms may both be removed.
After cleaning the filters, replace the filter assembly and fix it in
position correctly; this is essential for maintaining the efficient
operation of the dishwasher.
To remove the upper sprayer
arm, rotate the locking ring in
an anti-clockwise direction.
The upper sprayer arm should
be replaced with the holes
facing upwards.
Leaving the machine unused for extended
periods
• Disconnect the appliance from the electricity supply and
shut off the water tap.
The lower sprayer arm can be
removed by pressing on the side
tabs and pulling it upwards.
• Leave the door of the appliance ajar.
• When you return, run a wash cycle when the dishwasher is
empty.
* Only available in selected models.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and advice
This appliance was designed and manufactured in
compliance with current international safety standards.
The following information has been provided for safety
reasons and should therefore be read carefully.
Saving energy and respecting the
environment
EN
Saving water and energy
• Only begin a wash cycle when the dishwasher is full.
While waiting for the dishwasher to be filled, prevent
unpleasant odours using the Soak cycle (see Wash
cycles).
General safety
• The appliance was designed for domestic use inside
the home and is not intended for commercial or
industrial use.
• Select a wash cycle which is suited to the type of
crockery and to the soil level of the crockery using the
Table of wash cycles:
• The appliance must be used by adults only, to wash
domestic crockery in accordance with the
instructions in this manual.
- For dishes with a normal soil level, use the Eco wash
cycle, which guarantees low energy and water
consumption levels.
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
machine exposed to rain and storms.
• Do not touch the appliance when barefoot.
• When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
• The water supply tap must be shut off and the plug
should be removed from the electrical socket before
cleaning the appliance or carrying out any
maintenance work.
- If the load is smaller than usual activate the Half load
option* (see Start-up and use).
• If your electricity supply contract gives details of
electricity saving time bands, run wash cycles during
the periods when a lower tariff is applied. The
Delayed start* button (see Start-up and use) helps you
organise the wash cycles accordingly.
Phosphate-free and chlorine-free detergents
containing enzymes
• If the appliance breaks down, do not under any
circumstances touch the internal parts in an attempt
to perform the repair work yourself.
• We strongly recommend that you use detergents that
do not contain phosphates or chlorine, as these
products are harmful to the environment.
• Enzymes provide a particularly effective action at
temperatures around 50°C, and as a result detergents
containing enzymes can be used in conjunction with
low-temperature wash cycles in order to achieve the
same results as a normal 65°C wash cycle.
• Never touch the heating element.
• Do not lean or sit on the open door of the appliance:
this may cause the appliance to overturn.
• The door should not be left open as it may create a
dangerous obstacle.
• Keep detergent and rinse aid out of reach of children.
• The packaging material should not be used as a toy.
• To avoid wasting detergent, use the product in
appropriate quantities based on the manufacturer’s
recommendations, the hardness of the water and the
soil level and quantity of crockery to be washed. Even
if they are biodegradable, detergents contain
Disposal
• Disposal of packaging materials: observe local
legislation so that the packaging may be reused.
• The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
using the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the
materials inside the machine, while preventing
potential damage to the atmosphere and to public
health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations
regarding separated waste collection.
substances which may alter the balance of nature.
For further information relating to the correct disposal
of household appliances, owners may contact the
relevant public authority or the local appliance dealer.
* Only available in selected models.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
195063978.00
07/2007- Xerox Business Services
Whenever the appliance fails to work, check for a solution from the following list before calling for
Assistance.
EN
Malfunction:
Possible causes / Solutions:
• The plug has not been inserted into the electrical socket properly,
or there is no power in the house.
The dishwasher does not start.
• The dishwasher door has not been shut properly.
• A delayed start has been programmed (see Start-up and use).
• The dishwasher cycle has not yet finished.
No water drains out from the
dishwasher.
• The water outlet hose is bent (see Installation).
• The drain duct is blocked.
• The filter is clogged up with food residues.
• The dishes are rattling against each other or against the sprayer
arms.
The dishwasher makes
excessive noise.
• An excessive amount of foam has been produced: the detergent
has not been measured out correctly or it is not suitable for use in
dishwashers (see Start-up and use).
The dishes and glasses are
covered in a white film or
limescale deposits.
• The level of the refined salt is low or the dosage setting is not
suited to the hardness of the water (see Rinse aid and salt).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
• The crockery is made from non-stick material.
The dishes and glasses are
streaked or have a bluish
tinge.
• The rinse aid dosage is too high.
The crockery has not been dried
properly.
• The rinse aid has been used up or the dosage is too low (see Rinse
aid and salt).
• The rinse aid dispenser setting is not high enough.
• A wash cycle without a drying programme has been selected.
• The racks are overloaded (see Loading the racks).
• The crockery has not been arranged well.
The dishes are not clean.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (see Wash cycles).
• An excessive amount of foam has been produced: the detergent
has not been measured out correctly or it is not suitable for use in
dishwashers (see Start-up and use).
• The lid on the rinse aid compartment has not been shut correctly.
• The filter is dirty or blocked (see Care and maintenance).
• The refined salt level is low (see Rinse aid and salt).
• There is no water in the mains supply.
No water enters the
dishwasher/Shut off tap alarm.
(several short beeps are emitted)
• The water inlet hose is bent (see Installation).
• Turn on the tap and the appliance will start after a few minutes.
(the 2 (Normal) and 3 (Soak) WASH • The appliance lock has been activated because no action was
CYCLE indicator lights flash).
taken when the beeps* sounded. Switch off the machine, using the
ON/OFF button, turn on the tap and switch the machine back on
after 20 seconds by pressing the same button. Re-programme the
machine and restart the wash cycle.
Filters and trap blocked alarm.
• Switch off the appliance by pressing the ON/OFF button, remove
and clean the filters, inspect and clean the trap (see Care and
Maintenance), then switch the machine back on bby pressing the
same button again. Re-programme the machine and restart the
wash cycle.
(the 1 (Intensive) and 3 (Soak) WASH
CYCLE indicator lights flash).
Water loading solenoid valve
malfunction alarm
• Switch off the machine by pressing the ON/OFF button and switch it
back on after a minute. If the alarm continues, turn off the water tap
to reduce the risk of flooding, remove the plug from the electrical
socket and call Assistance.
(the 2 (Normal) WASH CYCLE
indicator lights flash).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|