Operating instructions
DISHWASHER
Contents
EN
Installation, 2-3-4
Positioning and levelling
English, 1
Connecting the water and electricity supplies
Advice regarding the first wash cycle
Technical data
Ecodesign Regulation
Electrical connection
Description of the appliance, 5
Overall view
Control panel
Loading the racks, 6
Lower rack
Cutlery basket
Upper rack
DIF 1614
Start-up and use, 7
Starting the dishwasher
Measuring out the detergent
Wash options
Wash cycles, 8
Table of wash cycles
Rinse aid and refined salt, 9
Measuring out the rinse aid
Measuring out the refined salt
Care and maintenance, 10
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the water inlet filter
Cleaning the filters
Leaving the machine unused for extended periods
Precautions and advice, 11
General safety
Disposal
Saving energy and respecting the environment
Troubleshooting, 12
Guarantee, 13
After Sales Service, 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
Before inserting the plug into the electrical socket, make
sure that:
Anti-condensation strip*
EN
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order
to protect it from any condensation which may form.
•
•
The socket is earthed and complies with current
regulations.
The socket can withstand the maximum load of the
appliance, which is indicated on the data plate located
on the inside of the door (see chapter entitled
Description of the appliance).
Advice regarding the first wash cycle
After the appliance has been installed, immediately before
running the first wash cycle, completely fill the salt
dispenser with water and add only then approximately 1 kg
of salt (see chapter entitled Rinse aid and refined salt). The
water may overflow: this is normal and is not a cause for
concern. Select the water hardness value (see chapter
entitled Rinse aid and refined salt). - After the salt has been
poured into the machine, the LOW SALT indicator light*
switches off.
•
•
The power supply voltage falls within the values
indicated on the data plate on the inside of the door.
The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to
replace the plug (see Assistance); do not use extension
cables or multiple sockets.
Once the appliance has been installed, the power
supply cable and the electrical socket should be easily
accessible.
If the salt container is not filled, the water softener and
the heating element may be damaged as a result.
The cable should not be bent or compressed.
Technical data
If the power supply cable is damaged, it must be re-
placed by the manufacturer or its Technical Assistance
Service in order to prevent all potential hazards. (See After
Sales Service)
width 59.5 cm
height 82 cm
depth 57 cm
Dimensions
Capacity
14 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
Power supply
voltage
See appliance data plate
See appliance data plate
Total absorbed
power
Fuse
See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2005/32/EC (Comm. Reg.
1275/2008) (Ecodesign)
-97/17/EC (Labelling)
-2002/96/EC (WEEE)
ECODESIGN REGULATION
ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a normal
soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption even
further, only run the dishwasher when it is full.
Standby consumption: Left-on mode consumption: 3 W – Off mode consumption: 1,3 W
Consumption data table for the main cycles
Standard conditions*
User conditions**
Energy consumption
(kWh/cycle)
1,65
Water consumption
(l/cycle)
16
16
Duration
(min/cycle)
150
Energy consumption
(kWh/cycle)
1,45
Water consumption
(l/cycle)
15
15
Duration
(min/cycle)
135
INTENSIVE
NORMAL
1,35
120
1,20
110
* Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.
**Data is obtained by recording values when the appliance is operational and loaded with user crockery.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
As the colours of the wires in the mains lead may not
Electrical Connection
EN
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market “ E” or
coloured Green or Green & Yellow.
Connect Brown wire to terminal marked “ L” or coloured
Red.
If your appliance is supplied with a 13 amp. fused plug it
can be plugged into a 13 amp socket for immediate use.
Before using the appliance please read the instruction
below.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Connect Blue wire to terminal marked “ N” or coloured
Black.
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse. A15 amp plug must be protected by a 15
amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved
fuse to BS 1362 should always be used, and the fuse
cover re-fitted. If the fuse cover is lost, the plug must not
be used until a replacement is obtained.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colours as indicated by the coloured marking or
the colour that is embossed in words on the base of the
plug. Replacements can be obtained directly from your
nearest Service Depot.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance
with the following code:
BLUE
BROWN
“ NEUTRAL” (“ N” )
“ LIVE” (“ L” )
Removing the plug:
GREEN AND YELLOW “ EARTH” (“ E” ) or
Ifyour appliance has a non-rewireable moulded plug and
you should wish to remove it to re-route the mains cable
through partitions, units etc., please esure that either:
- the plug is replaced by a fused 13 amp re-wireable
plug
- or:
bearing the BSI mark of approval
- the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with BS
5733) which
appliance.
is accessible without moving the
Disposing of the plug:
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally
inserted into a socket.
Instruction for connecting cable to an altenative
plug:
Important: the wires in the mains lead are coloured
in accordance with the following code:
Disposing of the appliance:
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the
plug body and dispose of it as described above.
Green & Yellow
Blue
- Earth
- Neutral
- Live
Brown
CAUTION:
- Once the appliance has been installed, the electrical plug
and socket should remain accessible.
- The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the
appliance
Overall view
EN
1.
2.
3.
4.
5.
6.
7.
8.
9.
Upper rack
Upper sprayer arm
Tip-up compartments
Rack height adjuster
Lower rack
Lower sprayer arm
Cutlery basket
Washing filter
Salt dispenser
10. Detergent and rinse aid dispensers
11. Data plate
12. Control Panel***
Control panel
Select wash
cycle button
Low Salt
indicator light*
ON/OFF
indicator light
Wash cycle indicator lights
Low Rinse Aid
indicator light*
ON/OFF/RESET
button
***Only in completely built-in models.
* Only available in selected models.
The number and type of wash cycles and options may vary depending on the dishwasher model.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the racks
Upper rack
Load this rack with delicate and lightweight crockery: glasses,
cups, saucers and shallow salad bowls.
Before loading the racks, remove all food residue from
crockery and empty liquids from glasses and cups.
After loading the appliance, make sure that the sprayer arms
can rotate freely.
EN
Lower rack and cutlery basket
The lower rack can hold pans, lids, plates, salad bowls, cutlery, etc.
Large plates and lids should ideally be placed at the sides of the rack.
Adjustable position tip-up compartments
The tip-up compartments
can be positioned at
different heights, to optimise
the arrangement of
crockery throughout the
rack. Wine glasses can be
placed safely in the tip-up
compartments, by inserting
the stem of each glass into
the corresponding slots.
Several dishwasher models are fitted with tip-up sections*, which
can be used in a vertical position when arranging plates or in a
horizontal position when arranging saucepans, salad bowls and
frying pans.
Adjusting the height of the upper rack
In order to make it easier to arrange the crockery, the upper rack
may be moved to a higher or lower level.
The height of the upper rack should ideally be adjusted
WHEN THE RACK IS EMPTY.
NEVER raise or lower the rack on one side only.
The type of cutlery basket may vary (modular or non-modular)
according to the dishwasher model. The non-modular basket
must only be positioned at the front of the lower rack.
Open the left and right guide rail stops
and pull out the rack; position it higher
or lower as required, slide it along the
guide rails until the front wheels are in
place and close the stops (see figure).
If the rack is fitted with Dual Space
handles*(see figure), pull out the upper
rack until it reaches its stop point, grip
the handles at the sides of the rack and
move it upwards or downwards, then
slowly let it fall back into place.
Both are fitted
with grilles
over the top,
for improved
cutlery ar-
rangement.
Items that should not be washed in the dishwasher
•
Wooden items, objects with wooden or horn handles or glued-
on parts.
•
•
•
•
Items made from aluminium, copper, brass, pewter or tin.
Items made from plastic material which is not heat-resistant.
Antique or hand-painted porcelain.
Antique silver. Silver that is not antique may, however, be
washed in the dishwasher using a delicate wash cycle,
provided that it does not come into contact with other metals.
Knives and other utensils with sharp edges must be placed
in the cutlery basket with the points facing downwards, or they
must be positioned horizontally in the tip-up compartments on
the upper rack.
We recommend the use of crockery which is dishwasher
safe.
*Only available in selected models. The number and position
may vary.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Start-up and use
Starting the dishwasher
Measuring out the detergent
EN
A good wash result also depends on the correct
amount of detergent being used; exceeding the
stated amount does not result in a more effective
wash and increases environmental pollution.
1. Turn the water tap on.
2. Open the door and press the ON/OFF button: you will
hear a short beep and the ON/OFF and wash cycle indicator
lights switch on for a few seconds.
3. Measure out the detergent (see below).
4. Load the racks (see chapter entitled Loading the racks).
5. Select the wash cycle in accordance with the type of
crockery and its soil level (see Table of wash cycles), by
pressing the SELECT WASH CYCLE button; the indicator
light corresponding to the selected wash cycle will switch
on.
Only use detergent which has been specifically
designed for dishwashers.
DO NOT USE washing up liquid.
Using excessive detergent may result in foam
residue remaining in the machine after the cycle
has ended.
7. Start the wash cycle by shutting the door: after a few
seconds have passed, a long beep signals the start of the
wash cycle.
The use of tablets is only recommended for
models which offer the MULTI-FUNCTIONAL
TABLETS option.
8. Two short beeps and one long one indicate the end of
the wash cycle and the indicator light corresponding to
the wash cycle flashes slowly. Open the door, switch off
the appliance by pressing the ON/OFF button, shut off the
water tap and unplug the appliance from the electricity
socket.
To achieve the best results from each washing
and drying cycle, powder detergent, rinse aid liquid
and salt should be used.
Compartment A: Washing detergent
Compartment B: Pre-wash detergent
9. Wait for a few minutes before removing the crockery, in
order to avoid burns. Unload the racks, beginning with the
lower level.
1. Open cover C by pressing
button D.
2. Pour in the detergent after
consulting the Table of wash
cycles:
- The machine will switch off automatically during
certain periods of inactivity, in order to minimise
electricity consumption.
• For powder detergent use
compartments A and B.
• For detergent in tablet form:
when the cycle requires 1 tablet,
place it in compartment A and close the cover; when it
requires 2, place the second tablet at the bottom of the
appliance.
Modifying a wash cycle in progress
If a mistake was made during the wash cycle selection process
it is possible to change the cycle, provided that it has only just
begun: open the door, taking care to avoid the escaping steam,
and press and hold the ON/OFF button; the machine will
switch off with a long beep. Switch the machine back on
using the ON/OFF button and select the new wash cycle using
the SELECT WASH CYCLE button; start the cycle by closing
the door.
3. Remove detergent residues from the edges of the
compartment and close the cover until it clicks.
Adding extra crockery
Without switching off the machine, open the door, taking
care to avoid the escaping steam, and place the crockery
inside the dishwasher. Close the door: the cycle starts from
the point at which it was interrupted.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a
power cut, the cycle stops. It starts again from the point at
which it was interrupted once the door has been shut or
the electricity supply is restored.
* Only available in selected models.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash cycles
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the
dishwasher, reduce the amount of detergent used accordingly.
EN
The number and type of wash cycles and options may vary depending on the dishwasher model.
Detergent
(A) = compartment A
(B) = compartment B
Wash
cycle
duration
(tolerance
±10%)
Wash
cycles
which Options
include
drying
Wash cycle selection
instructions
Wash cycle
Powder
Liquid
Tablets
Hrs. Min.
Environmentally-friendly wash
cycle with low energy
consumption levels, suitable for
pans and dishes.
29 g (A) 29 ml (A)
1 (A)
1 (A)
Yes
No
No
2:55’
1:50’
6 g (B)
6 ml (B)
1. Eco*
Normally soiled pans and dishes.
Standard daily wash cycle.
29 g (A) 29 ml (A)
Yes
No
6 g (B)
6 ml (B)
2. Normal
3. Soak
Pre-wash for dishes while
awaiting completion of the load
with the dishes from the next
meal.
No
No
No
No
No
0:08’
2:25’
Heavily soiled dishes and pans
(not to be used for delicate
items).
35 g (A) 35 ml (A)
25 g (A) 25 ml (A)
1 (A)
Yes
4. Intensive
Economic and fast wash to be
used for lightly soiled dishes.
(Run cycle immediately after use)
(2 plates + 2 glasses + 4 pieces
of cutlery + 1 saucepan + 1 small
frying pan).
1 (A)
1 (A)
No
No
No
0:35’
1:30’
5. Rapide
6. Crystal
Economic and fast wash for
delicate items which are sensitive
to high temperatures. (Run cycle
immediately after use) (glasses,
upper rack + delicate plates,
lower rack).
35 g (A) 35 ml (A)
Yes
Notes:
Optimum performance levels when using the "Rapide wash" cycle can be achieved by observing the maximum amounts of
crockery specified.
* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses
less energy and is les harmful to the environment.
Note for Test Laboratories: for detailed information relating to comparative EN testing conditions, please send an email to
the following address: ASSISTENZA_EN_LVS@indesitcompany.com
To make it easier to measure out the detergent, it is worth remembering that:
1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. of powder = approximately 5 ml of
liquid
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Rinse aid and refined salt
Hardness level 2 (1st cycle indicator light ON, 2nd cycle indicator
light flashing)
Only use products which have been specifically
designed for dishwashers.
EN
Hardness level 3 (1st and 2nd cycle indicator lights ON, 3rd cycle
indicator light flashing etc) up to maximum 5 levels.
- Press the P button repeatedly until the desired hardness level
has been reached (1-2-3-4-5*see Water hardness table).
- To exit the function, wait approximately few seconds or press
another option*button, or switch off the machine using the ON/
OFF button.
Do not use table salt or industrial salt, or washing
up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
rinse aid; however, we recommend that you add salt, especially
if you live in an area where the water is hard or very hard.
Follow the instructions given on the packaging.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
If you do not add salt or rinse aid, the LOW
SALT* and LOW RINSE AID* indicator lights remain
lit.
Average salt container
Water Hardness Table
capacity duration**
Level
°dH
°fH
mmol/l
0 - 1
1,1 - 2
2,1 - 3
3,1 - 6
months
7 months
5 months
3 months
2 months
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water runs
off surfaces more readily and therefore does not leave streaks or
marks.
1
0 - 6
0 - 10
2
3
4
6 - 11 11 - 20
12 - 17 21 - 30
17 - 34 31 - 60
The rinse aid dispenser should be filled:
• When the LOW RINSE AID*indicator light on the control
panel is illuminated;
5*
34 - 50 61 - 90
For values between 0°f and 10°f, we do not recommend the
6,1 - 9
2/3 weeks
use of salt. * this setting may cause a slight increase in the
1. Open the dispenser by turning
the lid (G) in an anticlockwise
direction.
2. Pour in the rinse aid, making sure
it does not overflow from the
duration of the cycles. ** for 1 wash cycle per day.
(°dH = hardness measured in German degrees - °f = hardness
measured in French degrees - mmol/l = millimoles per litre)
Measuring out the refined salt
In order to achieve the best possible results using a wash cycle,
make sure that the dispenser is never empty. Refined salt removes
limescale from the water, thus avoiding the formation of deposits
on crockery.
F
dispenser. If this happens, clean
the spill immediately with a dry
cloth.
G
3. Screw the lid back on.
NEVER pour the rinse aid directly into the appliance tub.
The salt dispenser is located in the lower part of the dishwasher
(see Description) and should be filled:
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
may adjust the quantity of rinse aid used. Use a screwdriver to
turn the dosage adjuster (F) to one of the 6 pre-set positions (the
default position is set to 4):
• When the green float*cannot be seen by simply looking at the
cap of the salt dispenser.
• When the LOW SALT* indicator light on the control panel is
illuminated;
• If there are streaks on the crockery, set the adjustment device
to a lower number (1-3).
1. Remove the lower rack and unscrew the
container cap (anticlockwise).
• If drops of water remain on the crockery or if there are limescale
marks present after the cycle has finished, set the adjuster to a
higher number (4-6).
2. The first time you do this: fill the water tank
right up to its edge.
3. Position the funnel* (see figure) and fill the
salt container right up to its edge (this should hold approximately
1 kg); it is not unusual for a little water to leak out.
4. Remove the funnel*and wipe any salt residue away from the
opening; rinse the cap under running water and then screw it on,
the head facing downwards so as to let the water flow out of the
four cracks which are arranged in a star shape on the lower part
of the cap. (Salt cap with green float*)
It is advisable to perform this procedure every time you add
salt to the container.
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash cycle (this could
damage the water softener beyond repair).
Setting the water hardness
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of appliance,
supplies water without limescale which is then used to wash the
crockery.
This dishwasher offers a setting which helps to reduce pollution
and optimises washing performance in accordance with the water
hardness level in your area. This information can be obtained
from the organisation which supplies your household with water.
- Open the door and switch on the machine by pressing the ON/
OFF button.
- Press the P button and hold for approximately 5 seconds; two
short beeps will sound and the indicator light corresponding to
the set degree of hardness will flash slowly on the control panel
(the water softening system is set to number 3).
When necessary, measure out the salt before a wash cycle
so that any saline solution which has leaked out of the salt
dispenser is removed.
E.g. Hardness level 1 (1st cycle indicator light flashing)
*Only available in selected models.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
Clean the water inlet filter at the tap outlet regularly.
- Turn off the water tap.
- Unscrew the end of the water inlet hose, remove the filter
and clean it carefully under running water.
- Replace the filter and screw the water hose back into
Shutting off the water and electricity
supplies
EN
•
Turn off the water tap after every wash cycle to avoid
leaks.
•
Always unplug the appliance when cleaning it and when
performing maintenance work.
position.
Cleaning the filters
Cleaning the dishwasher
The filter assembly consists of three filters which remove
food residues from the washing water and then recirculate
the water. They should be cleaned if you wish to achieve
the best results in every wash.
•
The external surfaces of the machine and the control
panel may be cleaned using a non-abrasive cloth which
has been dampened with water. Do not use solvents or
abrasive products.
Clean the filters regularly.
•
Any marks on the inside of the appliance may be
removed using a cloth dampened with water and a little
vinegar.
The dishwasher should not be used without filters, or if
the filter is loose.
• After several washes, check the filter assembly and if
necessary clean it thoroughly under running water, using
a non-metallic brush and following the instructions below:
1. Turn the cylindrical filter C in an anti-clockwise direction
and pull it out (fig. 1).
Preventing unpleasant odours
•
Always keep the door of the appliance ajar in order to
avoid moisture from forming and being trapped inside
the machine.
2. Remove the cup filter B by exerting a slight pressure on
the side flaps (fig. 2).
3. Slide out the stainless steel plate filter A (fig. 3).
4. Inspect the trap and remove any food residue. NEVER
REMOVE the wash cycle pump (black detail) (fig. 4).
•
Clean the seals around the door and detergent
dispensers regularly using a damp sponge. This will
avoid food becoming trapped in the seals, which is the
main cause behind the formation of unpleasant odours.
Cleaning the sprayer arms
Food residue may become encrusted onto the sprayer arms
and block the holes used to spray the water. It is therefore
recommended that the arms are checked from time to time
and cleaned with a small non-metallic brush.
The two sprayer arms may both be removed.
To remove the upper sprayer
arm, rotate the locking ring in an
anti-clockwise direction.
The upper sprayer arm should be
replaced with the holes facing
upwards.
1
2
The lower sprayer arm can be
removed by pressing on the side
tabs and pulling it upwards.
3
4
After cleaning the filters, replace the filter assembly and fix
it in position correctly; this is essential for maintaining the
efficient operation of the dishwasher.
Leaving the machine unused for
extended periods
Cleaning the water inlet filter*
•
Disconnect the appliance from the electricity supply and
shut off the water tap.
If the water hoses are new or have not been used for an
extended period of time, let the water run to make sure it is
clear and free of impurities before performing the necessary
connections. If this precaution is not taken, the water inlet
could become blocked and damage the dishwasher.
•
Leave the door of the appliance ajar.
• When you return, run a wash cycle when the dishwasher
is empty.
*Only available in selected models.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and advice
Saving energy and respecting the
This appliance was designed and manufactured in
compliance with current international safety standards. The
following information has been provided for safety reasons
and should therefore be read carefully.
EN
environment
Saving water and energy
•
Only begin a wash cycle when the dishwasher is full.
While waiting for the dishwasher to be filled, prevent
unpleasant odours using the Soak cycle (see Wash
cycles).
General safety
•
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
•
Select a wash cycle which is suited to the type of
crockery and to the soil level of the crockery using the
Table of wash cycles:
- For dishes with a normal soil level, use the Eco wash
cycle, which guarantees low energy and water
consumption levels.
•
•
Children should be supervised to ensure that they do
not play with the appliance.
The appliance was designed for domestic use inside
the home and is not intended for commercial or industrial
use.
- If the load is smaller than usual activate the Half load
option* (see Start-up and use).
If your electricity supply contract gives details of
electricity saving time bands, run wash cycles during
the periods when a lower tariff is applied. The Delayed
start* button (see Start-up and use) helps you organise
the wash cycles accordingly.
•
•
•
The appliance must be used by adults only, to wash
domestic crockery in accordance with the instructions
in this manual.
The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
machine exposed to rain and storms.
Phosphate-free and chlorine-free detergents
containing enzymes
•
•
Do not touch the appliance when barefoot.
When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
The water supply tap must be shut off and the plug should
be removed from the electrical socket before cleaning
the appliance or carrying out any maintenance work.
If the appliance breaks down, do not under any
circumstances touch the internal parts in an attempt to
perform the repair work yourself.
•
We strongly recommend that you use detergents that do
not contain phosphates or chlorine, as these products
are harmful to the environment.
•
•
•
Enzymes provide a particularly effective action at
temperatures around 50°C, and as a result detergents
containing enzymes can be used in conjunction with
low-temperature wash cycles in order to achieve the
same results as a normal 65°C wash cycle.
•
To avoid wasting detergent, use the product in
appropriate quantities based on the manufacturer’s
recommendations, the hardness of the water and the
soil level and quantity of crockery to be washed. Even if
they are biodegradable, detergents contain substances
which may alter the balance of nature.
•
•
Never touch the heating element.
Do not lean or sit on the open door of the appliance: this
may cause the appliance to overturn.
•
The door should not be left open as it may create a
dangerous obstacle.
•
•
Keep detergent and rinse aid out of reach of children.
The packaging material should not be used as a toy.
Disposal
•
Disposal of packaging materials: observe local
legislation so that the packaging may be reused.
•
The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states that
household appliances should not be disposed of using
the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the materials
inside the machine, while preventing potential damage
to the atmosphere and to public health. The crossed-
out dustbin is marked on all products to remind the owner
of their obligations regarding separated waste collection.
For further information relating to the correct disposal of
household appliances, owners may contact the relevant
public authority or the local appliance dealer.
* Only available in selected models.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for
Assistance.
EN
Problem:
Possible causes / Solutions:
The dishwasher does not start or
cannot be controlled
• Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and reset the program.
• The appliance has not been plugged in properly.
• The dishwasher door has not been shut properly.
The door won’t close
• The lock was released. Strongly push the door until a “clacking” noise is heard.
No water drains out from the
dishwasher.
• The dishwasher cycle has not yet finished.
• The water inlet hose is bent (see Installation).
• The drain duct is blocked.
• The filter is clogged up with food residues.
The dishwasher makes excessive
noise.
• The dishes are rattling against each other or against the sprayer arms.
• An excessive amount of foam has been produced: the detergent has not been
measured out correctly or it is not suitable for use in dishwashers (see Start-up
and use).
The dishes and glasses are
covered in a white film or
limescale deposits.
• The level of the refined salt is low or the dosage setting is not suited to the
hardness of the water (see Rinse aid and salt).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
The dishes and glasses are
• The rinse aid dosage is too high.
streaked or have a bluish tinge.
The crockery has not been dried
properly.
• A wash cycle without a drying program has been selected.
• The rinse aid has been used up or the dosage is too low (see Rinse aid and
salt).
• The rinse aid dispenser setting is not suitable.
• The crockery is made from non-stick material or plastic.
The dishes are not clean.
• The racks are overloaded (see Loading the racks).
• The crockery has not been arranged well.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (see Wash cycles).
• An excessive amount of foam has been produced: the detergent has not been
measured out correctly or it is not suitable for use in dishwashers (see Start-up
and use).
• The lid on the rinse aid compartment has not been shut correctly.
• The filter is dirty or blocked (see Care and maintenance).
• The refined salt level is low (see Rinse aid and salt).
The dishwasher does not take any • There is no water in the mains supply.
water in - Tap shut-off alarm
• The water inlet hose is bent (see Installation).
• Turn on the tap and the appliance will start after a few minutes.
• The appliance lock has been activated because no action was taken when the
(several short beeps* are emitted)
(the 2 (Normal) and 3 (Soak) WASH
CYCLES indicator lights flash).
beeps* sounded.
Switch off the appliance using the ON/OFF button, turn on the tap and switch
the appliance back on after 20 seconds by pressing the same button. Re-
program the appliance and restart the wash cycle.
Water inlet hose alarm / Water inlet • Switch off the appliance by pressing the ON/OFF button. Shut off the water tap
filter blocked
to eliminate the risk of flooding and remove the plug from the electrical socket.
Make sure the water inlet filter has not become blocked by impurities (see “Care
and maintenance” chapter).
(the 1 ECO), the 2 (Normal) and the
3 (Soak) WASH CYCLES indicator
lights flash).
* Only available in selected models.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
Guarantee
EN
12 months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for
twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of
either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to
you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,
batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-
DOMESTIC PREMISES.
5 Year Parts Guarantee
Indesit also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering
your appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for
our engineer’s time. To activate the extra parts warranty on your appliance, simply call our registration line on
08448 24 24 24 (Republic of Ireland 01 230 0800)
Extended Guarantees
We offer a selection of protection plans that enable you to fully cover yourself against the expense of repair
bills for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226
(Republic of Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you experience
any technical difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08448
224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an
engineer to call.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
After Sales Service
After Sales Service
EN
No one is better placed to care for your Indesit appliance during the course of its working life than us – the
manufacturer.
Essential Contact Information
Indesit Service
We are the largest service team in the UK and Ireland offering you access to 400 skilled telephone advisors and
1000 fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Indesit ownership. To activate your free 5 year parts guarantee you
must register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling and Disposal Information
As part of Indesit’s continued commitment to helping the environment, Indesit reserves the right to use quality,
recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the
door, plug, and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure
that the appliance can no longer be plugged into mains socket, and the door cannot be locked shut.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
15
Download from Www.Somanuals.com. All Manuals Search And Download.
195096602.01
05/2012 pb - Xerox Fabriano
EN
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|