Instruction manual
TUMBLE DRYER
Contents
EN
Important information, 2-3
EN
Installation, 4
Where to install the tumble dryer
Ventilation
English, 1
Electrical connections
Preliminary information
Description of the tumble dryer, 5-6
Features
Control panel
How to carry out a drying cycle, 7
Starting and selecting a programme
Programmes and options, 8-9-10
Programme chart
Special programmes
Options
Opening the door
IDCE 845
IDCE 845 S
Laundry, 11-12
Sorting laundry
Care labels
Special garments
Drying times
Warnings and suggestions, 13
General safety
Information on recycling and disposal
Saving energy and respecting the environment
Care and maintenance, 14
Disconnecting the power supply
Cleaning the filter after each cycle
Checking the drum after each cycle
Emptying the water container after each cycle
Cleaning the condenser unit
! Keep this manual at hand for immediate reference
whenever necessary. Always store this manual close to the
tumble dryer and remember to pass it on to any new
owners when selling or transferring the appliance, so they
may familiarise with the warnings and suggestions herein
contained.
Cleaning the tumble dryer
Troubleshooting, 15
Assistance and Guarantee, 16-17-18
Spare parts
! Read these instructions carefully: the following pages
contain important information on installation and useful
suggestions for operating the appliance.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Condenser unit - remove any fluff build-up
from the condenser on a monthly basis.
EN
Step 1
Open the condenser cover
- grip the handle and pull
towards you.
Step 2
Remove the condenser by
turning the 3 catches, then pull
the condenser towards you. (It is
normal for some residual water
to be left in the tubes).
Step 3
Clean the condenser with running
water over the rear side to
remove any fluff deposits.
Step 4
Replace the condenser unit;
make sure that the unit is
securely in place, that all 3
catches are fixed and that the
position arrows on the front end
of the condenser are pointing
upwards.
Failure to clean the condenser unit may cause
premature faults to the dryer.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Where to install the tumble dryer
Electrical connections
EN
• Install the dryer far from gas
ranges, stoves, radiators or
hobs, as flames may damage it.
If the dryer is installed below a
worktop, ensure there are 10
mm between the upper panel of
the dryer and any objects
Before plugging the appliance into the socket, check the following:
• Make sure your hands are dry.
• The socket must have an earth connection.
• The socket must be able to withstand the machine’s
maximum power output as indicated on the data plate (see
Description of the tumble dryer).
• The power supply voltage must fall within the values indicated
on the data plate (see Description of the tumble dryer).
• The socket must be compatible with the dryer’s plug.
Should this not be the case, replace the plug or the socket.
! Do not use extension cords.
! The dryer must not be installed outdoors, even if the space is
sheltered. It can be very dangerous if exposed to rain or storms.
! Once installed, the dryer’s electrical wire and plug must
be within reach.
above it, and 15 mm between
the sides of the machine and
the walls or furniture units
adjacent to it. This ensures
adequate air circulation.
Ventilation
! The power cord must not be bent or squashed.
! The power cord is supplied fitted with a BS1363 plug
and with a 13 amp BS1362 fuse. If it is necessary to fit a
replacement fuse, it must be a 13 Amp ASTA approved
to BS1362 type. WARNING: The plug must not be used
without a fuse cover. If a replacement fuse holder/cover is
required, it must be of the same colour coding or wording as
shown on the base of the plug.
• The room must be adequately ventilated while the dryer is
running. Make sure that the dryer is installed in a room free
of humidity and with adequate air circulation. The flow of air
around the dryer is essential to allow water to condense
during drying; the dryer will not function properly if it is
placed in an enclosed space or inside a cabinet.
! Some condensation may form if the dryer is used in a
Replacements are available from authorised dealers.
small or cold room.
Moulded plug
! We do not recommend installing the dryer in a cupboard;
moreover, never install the machine behind a lockable, sliding
or hinged door located on the opposite side of the dryer
door.
Water drain
If your dryer is installed next to a drain the water can be
plumbed into this drain. This does away with the need to
empty the water container. If the dryer is stacked onto or
installed next to a washing machine it can share the same
drain. The height of the drain must be less than 3' (1 m)
from the bottom of the dryer.
Changing the plug
The wires in the power cord are coloured in accordance
with the following.
Remove existing hose from position shown in picture A
and fit a suitable length of hose and connect as shown
in picture B.
13A ASTA approved fuse
to BS 1362.
Green and Yellow (Earth)
wire to terminal marked
“E”, symbol x, or coloured
green and yellow.
GREEN &
YELLOW
13 ampere fuse
BROWN
BLUE
! Make sure that the hose is not squashed or kinked
Brown (live) wire to teminal
marked “L” or coloured
red.
when the dryer is in its final location.
Blue (Neutral) wire to
terminal marked ”N” or
coloured black.
CROSS-BAR
CORD GRIP
! If the plug being replaced is a non-rewirable type, then the
cut-off plug must be disposed of safely. DO NOT leave it where
it can be inserted into a socket and create a shock hazard.
! The power cord should be checked periodically and replaced
by a cord specially prepared for this dryer and fitted only by
authorized technicians (see Service). New or longer power
cords are supplied at an extra charge by authorized dealers.
! The manufacturer denies any responsibility should any
of these rules not be followed.
Picture B
Picture A
!If in doubt about any of the above consult a qualified electrician.
Preliminary information
Once the tumble dryer is installed, clean the inside of the drum before
operating it and remove any dirt accumulated during transportation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of
the tumble dryer
Opening the door
Features
EN
Data plate
Water container
Press
the door
Model &
Serial
Numbers
Filter
Air
intake
grille
Condenser unit
(cover open)
Condenser cover
handle (pull to open)
Control panel
Options buttons
and indicator
lights
Timed Drying
button
On/Off
button
Start/Pause button and
indicator light
Programme
selection knob
Delay start
button
Display
Clean filter
indicator light
Clean
condenser unit
indicator light
Emptywatercontainer
indicator light
Cycle
phases
Timed
drying
icon
Delay
start icon
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ON/OFF/Reset button
Pressing the button normally will cause the machine to switch on or off. If the button is pressed for 3 seconds while the dryer is in
function, the machine will switch off and the running cycle will reset.
EN
Programme selection knob
Allows for setting the programme: turn until the indicator points towards the desired programme (see Starting and selecting a
programme).
Options buttons
Allows for selecting the options available for the selected programme. The relative indicator lights turn on when the option has been
selected (see Programmes and options).
START/PAUSE button and indicator light
When the green light flashes slowly, press the button to start the programme. When the cycle is under way, the indicator light remains
on. Press the button again to put the programme in the pause mode; the indicator light turns orange and starts flashing again.
Press the button again to resume the programme from the point it was interrupted (see Starting and selecting a programme).
Display
In section A, the selected “Timed drying” value is displayed; if the “Delay start” function was set, the time remaining to the start of the
selected programme will appear.
The duration of the selected programme is also displayed in this section.
In section B, the phase of the running programme is displayed:
Sun icon
Fan icon
: Drying cycle
: Cold air cycle
In section C, the maintenance indicator lights are displayed (Empty water container indicator light
Clean condenser unit indicator light) , see Indicator lights.
, Clean filter indicator light
,
B
C
A
Indicator lights
The indicator lights provide important information. They indicate the following:
The “Empty water container” indicator light
signals that the water container must be emptied.
If the water container fills during the course of the programme, the LED lights up. The dryer automatically starts a cold air cycle and the
START/PAUSE LED flashes orange. Press the START/PAUSE button to resume the cycle from the point it was interrupted.
In order to avoid this procedure, always empty the water container after using the tumble dryer (see Maintenance).
Before each programme, the “Clean filter” indicator light
(see Maintenance).
signals the fundamental importance of cleaning the filter before each load
The “Clean condenser unit” indicator light
signals the fundamental importance of cleaning the condenser regularly (see Maintenance).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
How to carry out
a drying cycle
Starting and selecting a programme
EN
1. Plug the dryer into the power supply socket.
2. Select the programme according to the type of laundry (see Laundry).
3. Open the door, ensure that the filter is clean and securely placed and that the water container is empty and correctly slotted (see
Maintenance).
4. Load the machine, making sure that no piece of laundry gets between the door and the relative seal. Close the door.
5. Press the ON/OFF button to start the machine.
6. After consulting the programme chart and the indications for each type of fabric (see Linen), turn the Programme selection knob
towards the programme corresponding to the type of laundry to be dried (see Programmes and options).
Warning: If the position of the programme selection knob changes after pressing the START/PAUSE button, the selected
programme will NOT be modified. To modify the programme, press the START/PAUSE button to put the programme in pause
mode (the indicator light flashes orange), then select a new programme and the relative options. Press the START/PAUSE button
to start the new programme.
7. Select the ”Timed Drying” function by pressing the relative button until reaching the desired level or time (see Programmes and
options).
8. If necessary, set the time of the delayed start and any other options (see Programmes and options).
9. Press the ALARM
button to sound a buzzer signalling the end of the programme.
10. Press the START/PAUSE button to start the drying cycle. The display will visualise the approximate time remaining.
Laundry can be checked while the drying programme runs and any garments already dry can be removed, while drying continues
for the remaining items. After closing the door, press the START/PAUSE button to resume machine operation.
11. The final COLD DRYING phase (i.e. the fabrics are cooled) activates during the last few minutes of the drying programme;
always allow this phase to terminate.
12. A buzzer signals when the programme ends (provided the relative option was selected). The word “End” will appear on the
display. Open the door, remove the laundry then clean the filter and replace it. Empty the water container and put it back in its slot
(see Maintenance).
If the “Post anti-crease” option was selected and laundry is not removed immediately, the drum will rotate garments at intervals for
10 hours or until the door is opened.
13. Disconnect the dryer from the power supply.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmes and options
Programme chart
EN
Max.
Cycle
duration
Programme
load
(kg)
Compatible options
Daily
Alarm – Pre anti-crease – Post anti-crease – High heat – Timed drying –
Delay start
Alarm – Pre anti-crease – Post anti-crease – High heat – Timed drying –
Delay start
Alarm – Pre anti-crease – Post anti-crease – High heat – Timed drying –
Delay start
Alarm – Pre anti-crease – Post anti-crease – High heat – Timed drying –
Delay start
Alarm – Pre anti-crease – Post anti-crease – High heat – Timed drying –
Delay start
Alarm – Pre anti-crease – Post anti-crease – High heat – Timed drying –
Delay start
1
2
3
4
5
6
Ready to Wear
Max.
Max.
Max.
Max.
3
Cotton Cupboard dry
Cotton Hanger dry
Cotton Iron dry
Synthetics Cupboard dry
Synthetics Iron dry
3
Special
Eco Time
Wool
7
8
9
2
1
0,5
3
Alarm – Pre anti-crease – Post anti-crease – Delay start
Alarm
Alarm – Pre anti-crease – Post anti-crease – Delay start
Alarm – Pre anti-crease – Post anti-crease – Delay start
Alarm – Pre anti-crease – Post anti-crease – Delay start
Silk
10 Jeans
11 Outwear
Sport
2
12 Sport Intensive
13 Sport Light
14 Special Shoes
Partial
4
4
Alarm – Pre anti-crease – Post anti-crease – Delay start
Alarm – Pre anti-crease – Post anti-crease – Delay start
2 pairs Alarm
Easy iron
Refresh
2,5
-
Alarm
Alarm
Special/Sport/Partial Programmes
Eco Time Programme
This programme is ideal for safely drying small loads in a short time, thereby optimising energy consumption. Suitable for loads of
up to 2 kg, it lasts about 1:00 (hrs:mins). The programme may last longer depending on the size and density of the load and on the
spin speed used during the wash cycle
We recommend checking whether garments are labelled with the symbol and to turn them inside out before drying them.
Wool Programme
This programme is specific for items that withstand tumble drying and are labelled with the symbol. It is suitable for loads of up
to 1 kg (about 3 jerseys). We recommend turning the garments inside out before drying them. This programme lasts about 1:00
(hrs:mins), although it may last longer depending on the size and density of the load and on the spin speed used during the wash
cycle. Garments dried with this programme are usually ready to be worn, although the edges of heavier garments may be slightly
damp. Leave them to dry naturally, as an additional drying process may damage them.
Unlike other materials, the shrinking process in wool is irreversible, i.e. the garment does not resume its original dimension and
shape.
This programme is not suited for acrylic items.
Silk Programme
This programme is specifically intended for drying delicate silk garments. It can be used for loads of up to 0.5 kg.
This programme lasts about 1:50 (hrs:mins), although it may last longer depending on the size and density of the load and on the
spin speed used during the wash cycle. Garments dried with this programme are usually ready to be worn, although the edges of
heavier garments may be slightly damp. If this occurs, remove the load, open the garments and reactivate the programme for a
short while.
Only for garments bearing the tumble dry symbol on the care label.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Jeans Programme
This programme is suited to washing cotton denim jeans. Turn the front pockets inside out before drying the jeans. It is suitable for
loads of up to 3 kg (about 4 pairs).
EN
This programme lasts about 1:25 (hrs:mins), although it may last longer depending on the size and of the load and on the spin
speed used in the wash cycle. Garments dried using this programme are usually ready to be worn, though edges and seams may
be slightly damp. In this occurs, turn the jeans inside out and reactivate the programme for a short while.
Use this cycle for 100% cotton garments only; do not mix dark and light colours and avoid using this programme for garments
with embroidery and accessories (elastic strings around the waist area, brooches, etc.); turn pockets inside out.
Outwear Programme
This programme is specific for drying water-repellent fabrics and sports jackets (e.g. Gore-Tex, polyester, nylon). Drying the
garment after a wash cycle has a beneficial effect as it reactivates the garment’s water-repellent treatment.
It can be used for loads of up to 2 kg. The programme lasts about 2:00 (hrs:mins), although it may last longer depending on the
size and density of the load and on the spin speed used during the wash cycle.
Sport Intensive Programme
This programme is studied for safely drying garments such as tracksuits and shorts bearing the symbol. It is ideal for clothes
which do not need to be dried fully. Suitable for loads of up to 4 kg, it lasts about 1:20 (hrs:mins), although it may last longer
depending on the size and density of the load and of the spin speed used during the wash cycle. We suggest turning garments
inside out before drying them.
Sport Light Programme
This programme is studied for safely drying garments such as tracksuits and shorts bearing the symbol. It is ideal for those
garments that do not need to be dried fully or which have to be ironed. Suitable for loads of up to 4 kg, it lasts about 1:10
(hrs:mins), although it may last longer depending on the size and density of the load and of the spin speed used during the washing
cycle. We suggest turning garments inside out before drying them.
Special Shoes Programme
This programme is specific for drying sports shoes of sizes 37-46. The shoes must have been previously washed and spun at a
minimum spin speed of 400 revolutions.
A specific shoe rack is provided and must be used, otherwise the dryer will be damaged if shoes are dried in the drum. Remove the
filter from its holder on the front part of the dryer and position the shoe rack.
Place shoelaces inside the shoes then load with the tips of the shoes facing downwards and the soles frontwards.
Drying times vary according to the shape and type of the shoe. If the shoes are not completely dry at the end of the programme,
restart the programme.
Do not dry shoes that have gel or flashing lights inside them. Only dry shoes made of synthetic material or rope. Once the
programme ends, remove the shoe rack and replace the filter into its holder.
Easy Iron
A short 10-minute programme that relaxes the garment’s fibres in order to facilitate ironing and folding.
This programme is particularly recommended for cotton or mixed cotton fabrics.
For optimal results, do not overload the drum (the following values refer to the weight of dry garments):
Fabric: maximum load
Cotton and mixed cotton: 2.5 kg
Synthetic garments: 2 kg
Jeans: 2 kg
Empty the dryer as soon as the programme ends; hang, fold or iron garments then place them in the wardrobe. If this is not
possible, repeat the programme.
As this is not a drying programme, it is not to be used for garments that are still wet.
The effect produced by the programme varies according to the characteristics of the each fabric: fabrics such as acrylic fibres or
Tencel® do not give the same results as traditional fibres (e.g. cotton).
Refresh
A short programme suitable for refreshing fibres and garments through the emission of cool air. It lasts about 0:20 (hrs:mins).
As this is not a drying programme, it is not to be used for garments that are still wet.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
The options allow for customising the selected programme according to one’s own needs.
EN
Timed drying
After selecting a programme, press the “Timed drying” button to enter a drying time. Every time this button is pressed, the duration of
the selected drying cycle appears on the display. When pressed the first time, the highest allowed value for the selected cycle appears
on the display. When pressed each of the following times, the set time is reduced until OFF appears.
Three buzzer signals are emitted if the timed drying option is not available.
The selected time remains visualised after the start of the programme and cannot be modified after pressing the START/PAUSE
button.
Delay Start
The start of some programmes (see Programmes and options) may be delayed up to 24 hours. Press the button repeatedly to
enter the desired delay time. Before setting a delayed start, make sure that the water container is empty and that the filter is clean.
Pre Anti-Crease
When this option is selected in addition to the “Delay start” option, the drum rotates garments at intervals during the delay period
to avoid creases forming.
Post Anti-Crease
When this option is selected, the drum rotates garments at intervals after the cold drying cycle has ended, in order to avoid
creases forming on garments if they cannot be immediately removed at the end of the programme. During this phase, the indicator
light is turned on.
High Heat
When a drying time is selected, pressing this button sets a high heat drying and the indicator light above the button lights up. The
timed programmes are pre-set to low heat.
Alarm
A buzzer sounds at the end of the drying cycle to signal that the programme has ended and the garments are ready to be
removed.
Not all options are available on all programmes (see Programmes and options). If the button of an unavailable option is pressed,
the buzzer emits three signals. If an option is available, a single buzzer signal sounds and the option indicator light next to the
button lights up to confirm the selected option.
Opening the door
If the door is opened (or the START/PAUSE button is pressed) while a programme is running, the dryer stops and the following
may occur:
• The START/PAUSE button flashes orange.
• When a delayed start is running, the delay countdown continues. It is necessary to press the START/PAUSE button to resume
the “Delay start” programme. The “Delay start” indicator light flashes and the display visualises the time remaining to the start of the
selected programme.
• It is necessary to press the START/PAUSE button to resume the programme. The progress indicator lights signal the running
phase and the START/PAUSE indicator light stops flashing and turns green.
• During the post anti-crease phase, the programme ends. Pressing the START/PAUSE button reactivates a new programme from
the beginning.
• By turning the Programme selection knob, a new programme is selected and the START/PAUSE indicator light flashes green.
This procedure can be used to select the Cold drying programme to cool garments if they are judged to be dry enough.
Press the START/PAUSE button to start the new programme.
Note: In the event of a power cut, turn the power switch off and remove the plug; when the electricity supply returns, press the
START/PAUSE button to resume the programme.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Laundry
Sorting laundry
Care labels
• Check the symbols on the care labels of the various
garments to verify whether the garments can be safely
tumble dried.
Always check the care labels, especially when placing
garments in the tumble dryer for the first time. Below are the
most commonly used symbols:
EN
• Sort laundry according to the type of fabric.
• Empty all pockets and check for loose buttons.
• Close zips and hooks and fasten belts and strings without
tightening them.
May be tumble dried.
Do not tumble dry.
• Wring out garments to remove the maximum amount of
water possible.
Tumble dry – high heat.
Tumble dry – low heat.
! Do not load the dryer when garments are dripping wet.
Maximum load sizes
Do not overload the drum.
Items not suitable for tumble drying:
The following values indicate the weight of dry garments:
Natural fibres: maximum 7.5 kg
Synthetic fibres: maximum 3 kg
• Items containing rubber parts or similar materials, or
plastic film covering (pillows, cushions or PVC sports
jackets), any type of inflammable object or objects
containing inflammable substances (used towels
containing hairspray).
! Do not overload the dryer as this may result is reduced
drying performance.
Typical weights
• Glass fibres (certain types of draperies).
Note: 1 kg = 1000 g
• Items which have been previously dry cleaned.
• Items marked with the ITLC symbol (“Special garments”)
, which may be washed using special household
products. Follow instructions carefully.
Garments
Cotton
Other
150 g
100 g
500 g
350 g
Blouse
Dress
• Large bulky items (duvets, sleeping bags, pillows,
cushions, large bedcovers, etc.) that expand when dried
and hamper air circulation inside the tumble dryer.
Cotton
Other
700 g
Jeans
1,000 g
10 nappies
300 g
200 g
Cotton
Other
Shirt
T-shirt
125 g
Household linen
Cotton
Other
1,500 g
1,000 g
Duvet cover
(double bed)
Large tablecloth
700 g
250 g
100 g
700 g
350 g
500 g
Small tablecloth
Tea cloth
Bath towel
Hand towel
Double bed
sheet
350 g
Single bed sheet
When mixing synthetic fibres with cotton garments, the
latter may still be damp at the end of the drying cycle. If this
happens, simply put them through a short drying cycle.
Note: when setting the duration of the drying cycle,
remember that the cold drying phase runs during the last 10
minutes, during which the dryer does not dry the garments.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Special garments
• Heat setting.
EN
Blankets and bedcovers: acrylic items (Acilian, Courtelle,
Orion, Dralon) must be dried with great care at low heat.
Avoid drying for long periods.
• Temperature of the room: the lower the temperature of
the room, the longer it will take for the dryer to dry
clothing.
Creased or pleated garments: read the drying instructions
supplied by the manufacturer.
• Bulk: certain bulky items require special care during the
drying process. We suggest removing these items and
replacing them in the dryer once they have been shaken
out: repeat this procedure several times during the course
of the drying cycle.
Starched garments: do not dry together with non-
starched items. Remove the maximum amount of starch
solution possible before placing these items in the dryer. Do
not over-dry: starch turns powdery leaving garments limp –
this defeats its purpose.
! Do not over-dry items.
All fabrics contain natural dampness which helps to keep
them soft and fluffy.
Drying times
The drying times provided refer to the automatic Cupboard
dry programmes.
Drying times are approximate and may vary depending on
the following:
The Timed drying settings are also indicated to enable you
to select the most suitable timed option.
The weight refers to dry items.
• Amount of water retained by items after the spin cycle:
towels and delicate items retain a lot of water.
• Fabrics: items of the same fabric, but with different texture
and thickness may have different drying times.
• Amount of laundry: single items and small loads may take
longer to dry.
• Drying: if items are to be ironed, they can be removed
from the dryer while still slightly damp. Items that require
complete drying can be left longer.
Drying times
Cotton
Intensive drying
Drying times after 800-1000 rpm wash cycles
Half load
3 kg
Full load
7.5 kg
1 kg
2 kg
4 kg
5 kg
6 kg
7 kg
Automatic
(hrs:mins)
Timed
0:30-0:50
0:50-1:10
1:10-1:20
1:20-1:40
1:40-2:00
2:00-2:20
2:20-2:30
2:10-2:50
0:30 or 1:00 1:00 or 1:30 1:00 or 1:30 1:30 or 2:00 1:30 or 2:00 2:20 or 2:40 2:20 or 2:40 2:20 or 3:00
(hrs:mins)
Synthetics
Intensive drying
Drying times after wash cycles at lower speeds
Half load
2 kg
Full load
3 kg
1 kg
Automatic
(hrs:mins)
Timed
0:30 - 0:40
0:40 - 0:50
0:50 - 1:10
0:30 or 1:00
0:30 or 1:00
1:00 or 1:30
(hrs:mins)
Delicates
Normal drying
Drying times after wash cycles at lower speeds
Half load
1 kg
Full load
2 kg
Automatic
(hrs:mins)
Timed
0:40 - 1:20
1:20 - 2:20
0:30 or 1:00 or 1:30
1:00 or 1:30 or 2:00
(hrs:mins)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
and suggestions
• Complete each programme with the relative cold drying
phase.
! This appliance was designed and manufactured in
compliance with current international safety standards. The
following information is provided for safety reasons and
must be read carefully.
EN
• Do not switch the tumble dryer off if items that are still
warm are inside it.
• Clean the filter after each use (see Maintenance).
• Empty the water container and put it back in place after
each use (see Maintenance).
General safety
• Clean the condenser unit regularly (see Maintenance).
• Do not allow lint to build up around the tumble dryer.
• Avoid climbing on the top of the dryer as this may
damage the appliance.
• This tumble dryer must not be used by persons (including
children) with physical, sensory or mental impairments or
with little experience and knowledge of the appliance,
unless they are supervised or have been adequately
instructed on its use by the person responsible for their
safety.
• Always comply with electrical regulations and
requirements (see Installation).
• Always purchase original accessories and spare parts
(see Assistance).
• This tumble dryer is designed for domestic and non-
professional use.
! WARNING: Never stop the dryer before the end of the
drying cycle unless all items have been quickly removed and
hung in order to dispel heat.
• Do not touch the appliance while barefoot or with wet
hands or feet.
• Unplug the appliance by pulling on the plug, not the cord.
• Do not allow children near the appliance while it is in
function. After use, switch the appliance off and unplug it.
Keep the appliance door closed to prevent children using
it as a toy.
Information on recycling and
disposal
As part of our continual commitment towards environmental
protection, we reserve the right to use recycled quality
components to reduce costs for our customers and to
minimise materials wastage.
• Children must be supervised to ensure that they do not
play with the appliance.
• The appliance must be correctly installed and receive
adequate ventilation. The air intake on the front part of
the dryer and the air vents on the rear must never be
obstructed (see Installation).
• Disposing of the packaging materials: follow local
regulations to allow for recycling of packaging materials.
• In order to minimise the risk of injury to children, remove
the door and plug, then cut the power supply cord flush
with the appliance. Dispose of these parts separately to
prevent the appliance from being connected to a power
supply socket.
• Never use the dryer on carpeting with high pile as this
may prevent air from entering the dryer from the base.
• Check whether the dryer is empty before loading it.
•
The rear part of the dryer may become very hot:
do not touch it while the appliance is in function.
• Do not use the dryer unless the filter, water container and
condenser are properly positioned (see Maintenance).
• Do not use liquid fabric softener in the dryer; add it to the
final rinse of the wash cycle.
Disposal of old household appliances
European Directive 2002/96/EC concerning Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
using the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling materials
comprising the machine, while preventing potential damage
to public health and the environment. The crossed-out
wheeled bin symbol appears on all products to remind
owners of the obligations regarding separate waste
collection.
• Do not overload the dryer (see Laundry for the maximum
load sizes).
• Do not add items that are dripping wet.
• Tumble dry items only if they have been washed with
water and detergent, and have been rinsed and put
through a spin cycle. Drying items that have NOT been
washed with water may cause the risk of fire.
• Always read the instructions on the care label carefully
(see Laundry).
Owners should contact their local authorities or appliance
dealers for further information concerning the correct
disposal of household appliances.
• Do not tumble dry items that have been treated with
chemical products.
• Never tumble dry items that are contaminated with
inflammable substances (cooking oil, acetone, alcohol,
petrol, kerosene, stain removers, turpentine, waxes, wax
removers and hairspray), unless they have been washed
in hot water with an extra amount of detergent.
• Do not tumble dry rubber, rubber-backed articles and
garments, cushions with foam rubber padding, latex
foam, rubber, plastic, shower caps, water-resistant
fabrics, nappy pants or liners, polyethylene and paper.
• Remove all objects from pockets, particularly lighters
(risk of explosion).
Saving energy and respecting the
environment
• Wring out items before tumble drying them to remove
the maximum amount of water possible (if they are
previously washed in a washing machine, select a spin
cycle). This ensures that energy is saved during tumble
drying.
• Always use the tumble dryer at full load to save energy:
single items and small loads may take longer to dry.
• Clean the filter at the end of each cycle to reduce energy
consumption costs (see Maintenance).
• Do not tumble dry large, excessively bulky items.
• Do not tumble dry acrylic fibres at high temperatures.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
Disconnecting the power supply
Emptying the water container after
each cycle
EN
! Disconnect the dryer when not in use or during cleaning
Remove the water container and empty it into a sink or
other suitable drain outlet, then replace it correctly.
Always check the water container and empty it before
starting a new drying cycle.
and maintenance operations.
Cleaning the filter after each cycle
The filter is a fundamental component of the dryer: its
function is to collect lint and fluff that form during drying.
Clean the filter once drying is completed, by rinsing it under
running water or cleaning it with a vacuum cleaner. Should the
filter become clogged, the flow of air inside the dryer will be
seriously hampered: drying times becomes longer and more
energy is consumed. Moreover, the dryer may become
damaged.
Cleaning the condenser unit
• Remove the condenser unit regularly (monthly) and clean
off any fluff deposits from the plates by rinsing it with cold
water running on the rear end of the condenser.
Removing the condenser:
1. Disconnect the dryer from the power supply and open the
door.
The filter is located in front of
the dryer seal (see Picture).
2. Open the condenser cover (see Picture), unlock the three
catches by turning them 90° anti-clockwise, then pull on
the grip to remove the condenser.
Removing the filter:
1. Pull the filter’s plastic
3. Clean the surface of the seals and replace the unit with the
arrows pointing upwards, while making sure that the
catches are securely fixed.
handle upwards (see
Picture).
2. Clean the fluff off the filter
and replace it correctly.
Cleaning the tumble dryer
• The external metal and plastic parts and the rubber parts
can be cleaned with the aid of a damp cloth.
• Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, fluff or dust
deposits. Furthermore, remove any lint deposits from the
front part of the condenser and from the filter area, using a
vacuum cleaner every so often.
Ensure that the filter is
placed flush with the dryer
seal.
! Do not use the dryer unless the filter has been replaced in
its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items
(handkerchiefs) that could have been left inside the dryer.
! Do not use solvents or abrasives.
! The dryer uses ball bearing components that do not
require lubrication.
!Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and
mechanical parts work safely (see Assistance).
Cleaning the drum
! Avoid using abrasives, steel wool or stainless steel
cleaning agents to clean the drum.
A coloured film may appear on the stainless steel drum
surface: it may be caused by a combination of water and/or
cleaning agents such as wash-softeners. This coloured film
does not affect the dryer’s performance.
Water
container
Filter
Tap
Rear
Condenser
unit
Air intake
Front
Condenser unit
Condenser cover
Catches
Handle
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you feel that the dryer is not working properly, consult the following troubleshooting suggestions before contacting the Technical
Assistance Centre (see Assistance).
EN
Problem:
Possible causes / Solutions:
The dryer does not start.
• The plug has not been inserted far enough into the socket to make contact.
• There has been a power cut.
• The fuse has burned out. Try connecting another appliance to the same socket.
• If an extension cord is used, try connecting the dryer plug directly into the socket.
• The door has not been closed properly.
• The programme has not been set correctly (see How to carry out a drying cycle).
• The START/PAUSE button has not been pressed (see How to carry out a drying cycle).
The drying cycle does not start.
• A delayed start time has been set (see Programmes and options).
• The START/PAUSE button has been pressed; a short delay follows before the
dryer starts running. Wait for the drying cycle to start; do not press the START/
PAUSE button otherwise the dryer switches to the pause mode and the drying
cycle will not start.
Drying times are too long.
• The filter has not been cleaned (see Maintenance).
• The water container must be emptied? The “Empty water container” indicator light
flashes and the message appears “H2O” (see Maintenance).
• The condenser needs to be cleaned (see Maintenance).
• The heat setting is not suited to the type of fabric to be dried (see Programmes and
options).
• An incorrect drying time was selected for the type of load (see Laundry).
• The items are too wet (see Laundry).
• The air intake grille are clogged up (see “Installation” and “Care and Maintenance”).
• The dryer is overloaded (see Laundry).
• The water container was probably not emptied before starting the programme. Do
not wait for the signal for emptying the water container, but always check and
empty it before starting a new drying programme (see Description of the tumble
dryer).
The “Empty water container”
indicator light flashes, but the
dryer has been running for a short
time.
The “Empty water container”
indicator light is on but the water
container is not full.
• It is normal: the “Empty water container” indicator light flashes when the water
container is full. If the indicator light is on but is not flashing, it only signals that the
water container must be emptied (see Description of the tumble dryer).
The programme is finished but
the items are damper than
expected.
! For safety reasons, the dryer programmes last a maximum of 4 hours. If an
automatic programme has not detected the final dampness level required in this
interval, the dryer completes the programme and stops. Check the above points
and repeat the programme; if the items are still damp, contact the Technical
Assistance Centre (see Assistance).
The code “F” appears on the
display followed by one or two
numbers, the options indicator
lights and the pause indicator
light flash.
• If the display visualises F10 or F15, switch the appliance off and unplug it, then clean
the filter and the condenser (see Maintenance). Reinsert the plug, switch the
appliance on and start another programme. If the display still visualises F10 or F15,
contact the Technical Assistance Centre (see Assistance). If the display still
visualises other numbers, mark the code and contact the Technical Assistance
Centre (see Assistance).
“dOn” briefly appears on the
display every 6 seconds.
• The appliance is in “Demo” mode. Press the ON/OFF and START/PAUSE buttons
and keep them pressed for 3 seconds. The display visualises “dOn” for 3
seconds, then the dryer starts functioning normally.
The “Remaining time” indicator
changes during the drying cycle.
• The remaining time is constantly monitored during the drying cycle and is updated
to show the best forecast. It is normal for the displayed time to increase during the
cycle.
The dryer is noisy during the first
few minutes of operation.
• This is normal, especially if the dryer has not been used for a long time. If the noise
persists during the entire cycle, contact the Technical Assistance Centre.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Assistance
Before calling the Technical Assistance Centre:
Spare parts
EN
• Follow the troubleshooting guide to check whether
problems can be solved personally (see Troubleshooting).
• If not, switch the dryer off and contact the Technical
Assistance Centre closest to you.
This dryer is a complex machine. Attempting to repair it
personally or with the aid unqualified personnel may put
the safety of people at risk, damage the machine or
invalidate the spare parts guarantee.
Always contact a qualified technician when experiencing
problems with this machine. The spare parts were
designed exclusively for this machine and should not be
used for any other purpose.
Provide the following data when contacting the
Technical Assistance Centre:
• name, address and postal code
• telephone number
• type of malfunction
• date of purchase
• the appliance model (Mod.)
• the dryer’s serial number (S/N)
This information can be found on the data plate located
behind the door.
Comparative programmes
• recommended programmes for the EN61121 comparative test.
Programme (EN61121)
Programme to be selected
Load size
Cotton drying cycle
Cotton drying ironing
Easy care fabric
Cotton Cupboard dry
Cotton Iron dry
7.5 kg
7.5 kg
3 kg
Synthetic Cupboard dry
! Note: this is not a complete list of the programme options (see Starting and selecting a programme).
This appliance conforms to the following EEC directives:
- 2006/95/EC (Low Voltage Directive)
- 89/336/EEC, 92/31/EEC, 93/68/EEC (Electromagnetic Compatibility Directive).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
12 Months Parts and Labour Guarantee
EN
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve
months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
Replacement of any consumable item or accessory. These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR
NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Indesit also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering your
appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for our engineer's
time. To activate the extra parts warranty on your appliance, simply call our registration line on 08448 24 24 24
(Republic of Ireland 01 230 0800)
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills for
the life of your policy. To find the ideal plan for you please call our advice line on
08448 226 226 (Republic of Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any
technical difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08448 224 224
(Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an engineer to call.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
After Sales Service
EN
No one is better placed to care for your Indesit appliance during the course of its working life than us - the manufacturer.
Essential Contact Information
Indesit Service
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified
engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean
your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Indesit ownership. To activate your free 5 year parts guarantee you must
register your appliance with us.
UK: 08448 24 24
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling & Disposal Information
As part of Indesit's continued commitment to helping the environment, Indesit reserves the right to use quality, recycled
components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door, plug
and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the appliance can
no longer be plugged into a mains socket, and the door cannot be locked shut.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
19
Download from Www.Somanuals.com. All Manuals Search And Download.
195075237.00
01/2009
-
Xerox Fabriano
EN
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|